linux-stable/drivers/scsi/ses.c

924 lines
21 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
/*
* SCSI Enclosure Services
*
* Copyright (C) 2008 James Bottomley <James.Bottomley@HansenPartnership.com>
*/
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 08:04:11 +00:00
#include <linux/slab.h>
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/enclosure.h>
#include <asm/unaligned.h>
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_dbg.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_driver.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport_sas.h>
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct ses_device {
unsigned char *page1;
unsigned char *page1_types;
unsigned char *page2;
unsigned char *page10;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
short page1_len;
short page1_num_types;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
short page2_len;
short page10_len;
};
struct ses_component {
u64 addr;
};
static bool ses_page2_supported(struct enclosure_device *edev)
{
struct ses_device *ses_dev = edev->scratch;
return (ses_dev->page2 != NULL);
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
static int ses_probe(struct device *dev)
{
struct scsi_device *sdev = to_scsi_device(dev);
int err = -ENODEV;
if (sdev->type != TYPE_ENCLOSURE)
goto out;
err = 0;
sdev_printk(KERN_NOTICE, sdev, "Attached Enclosure device\n");
out:
return err;
}
#define SES_TIMEOUT (30 * HZ)
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
#define SES_RETRIES 3
static void init_device_slot_control(unsigned char *dest_desc,
struct enclosure_component *ecomp,
unsigned char *status)
{
memcpy(dest_desc, status, 4);
dest_desc[0] = 0;
/* only clear byte 1 for ENCLOSURE_COMPONENT_DEVICE */
if (ecomp->type == ENCLOSURE_COMPONENT_DEVICE)
dest_desc[1] = 0;
dest_desc[2] &= 0xde;
dest_desc[3] &= 0x3c;
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
static int ses_recv_diag(struct scsi_device *sdev, int page_code,
void *buf, int bufflen)
{
int ret;
unsigned char cmd[] = {
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
RECEIVE_DIAGNOSTIC,
1, /* Set PCV bit */
page_code,
bufflen >> 8,
bufflen & 0xff,
0
};
unsigned char recv_page_code;
unsigned int retries = SES_RETRIES;
struct scsi_sense_hdr sshdr;
const struct scsi_exec_args exec_args = {
.sshdr = &sshdr,
};
do {
ret = scsi_execute_cmd(sdev, cmd, REQ_OP_DRV_IN, buf, bufflen,
SES_TIMEOUT, 1, &exec_args);
} while (ret > 0 && --retries && scsi_sense_valid(&sshdr) &&
(sshdr.sense_key == NOT_READY ||
(sshdr.sense_key == UNIT_ATTENTION && sshdr.asc == 0x29)));
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (unlikely(ret))
return ret;
recv_page_code = ((unsigned char *)buf)[0];
if (likely(recv_page_code == page_code))
return ret;
/* successful diagnostic but wrong page code. This happens to some
* USB devices, just print a message and pretend there was an error */
sdev_printk(KERN_ERR, sdev,
"Wrong diagnostic page; asked for %d got %u\n",
page_code, recv_page_code);
return -EINVAL;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
static int ses_send_diag(struct scsi_device *sdev, int page_code,
void *buf, int bufflen)
{
int result;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
unsigned char cmd[] = {
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
SEND_DIAGNOSTIC,
0x10, /* Set PF bit */
0,
bufflen >> 8,
bufflen & 0xff,
0
};
struct scsi_sense_hdr sshdr;
unsigned int retries = SES_RETRIES;
const struct scsi_exec_args exec_args = {
.sshdr = &sshdr,
};
do {
result = scsi_execute_cmd(sdev, cmd, REQ_OP_DRV_OUT, buf,
bufflen, SES_TIMEOUT, 1, &exec_args);
} while (result > 0 && --retries && scsi_sense_valid(&sshdr) &&
(sshdr.sense_key == NOT_READY ||
(sshdr.sense_key == UNIT_ATTENTION && sshdr.asc == 0x29)));
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (result)
sdev_printk(KERN_ERR, sdev, "SEND DIAGNOSTIC result: %8x\n",
result);
return result;
}
static int ses_set_page2_descriptor(struct enclosure_device *edev,
struct enclosure_component *ecomp,
unsigned char *desc)
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
{
int i, j, count = 0, descriptor = ecomp->number;
struct scsi_device *sdev = to_scsi_device(edev->edev.parent);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct ses_device *ses_dev = edev->scratch;
unsigned char *type_ptr = ses_dev->page1_types;
unsigned char *desc_ptr = ses_dev->page2 + 8;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
/* Clear everything */
memset(desc_ptr, 0, ses_dev->page2_len - 8);
for (i = 0; i < ses_dev->page1_num_types; i++, type_ptr += 4) {
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
for (j = 0; j < type_ptr[1]; j++) {
desc_ptr += 4;
if (type_ptr[0] != ENCLOSURE_COMPONENT_DEVICE &&
type_ptr[0] != ENCLOSURE_COMPONENT_ARRAY_DEVICE)
continue;
if (count++ == descriptor) {
memcpy(desc_ptr, desc, 4);
/* set select */
desc_ptr[0] |= 0x80;
/* clear reserved, just in case */
desc_ptr[0] &= 0xf0;
}
}
}
return ses_send_diag(sdev, 2, ses_dev->page2, ses_dev->page2_len);
}
static unsigned char *ses_get_page2_descriptor(struct enclosure_device *edev,
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct enclosure_component *ecomp)
{
int i, j, count = 0, descriptor = ecomp->number;
struct scsi_device *sdev = to_scsi_device(edev->edev.parent);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct ses_device *ses_dev = edev->scratch;
unsigned char *type_ptr = ses_dev->page1_types;
unsigned char *desc_ptr = ses_dev->page2 + 8;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (ses_recv_diag(sdev, 2, ses_dev->page2, ses_dev->page2_len) < 0)
return NULL;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
for (i = 0; i < ses_dev->page1_num_types; i++, type_ptr += 4) {
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
for (j = 0; j < type_ptr[1]; j++) {
desc_ptr += 4;
if (type_ptr[0] != ENCLOSURE_COMPONENT_DEVICE &&
type_ptr[0] != ENCLOSURE_COMPONENT_ARRAY_DEVICE)
continue;
if (count++ == descriptor)
return desc_ptr;
}
}
return NULL;
}
/* For device slot and array device slot elements, byte 3 bit 6
* is "fault sensed" while byte 3 bit 5 is "fault reqstd". As this
* code stands these bits are shifted 4 positions right so in
* sysfs they will appear as bits 2 and 1 respectively. Strange. */
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
static void ses_get_fault(struct enclosure_device *edev,
struct enclosure_component *ecomp)
{
unsigned char *desc;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (!ses_page2_supported(edev)) {
ecomp->fault = 0;
return;
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
desc = ses_get_page2_descriptor(edev, ecomp);
if (desc)
ecomp->fault = (desc[3] & 0x60) >> 4;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
static int ses_set_fault(struct enclosure_device *edev,
struct enclosure_component *ecomp,
enum enclosure_component_setting val)
{
unsigned char desc[4];
unsigned char *desc_ptr;
if (!ses_page2_supported(edev))
return -EINVAL;
desc_ptr = ses_get_page2_descriptor(edev, ecomp);
if (!desc_ptr)
return -EIO;
init_device_slot_control(desc, ecomp, desc_ptr);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
switch (val) {
case ENCLOSURE_SETTING_DISABLED:
desc[3] &= 0xdf;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
break;
case ENCLOSURE_SETTING_ENABLED:
desc[3] |= 0x20;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
break;
default:
/* SES doesn't do the SGPIO blink settings */
return -EINVAL;
}
return ses_set_page2_descriptor(edev, ecomp, desc);
}
static void ses_get_status(struct enclosure_device *edev,
struct enclosure_component *ecomp)
{
unsigned char *desc;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (!ses_page2_supported(edev)) {
ecomp->status = 0;
return;
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
desc = ses_get_page2_descriptor(edev, ecomp);
if (desc)
ecomp->status = (desc[0] & 0x0f);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
static void ses_get_locate(struct enclosure_device *edev,
struct enclosure_component *ecomp)
{
unsigned char *desc;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (!ses_page2_supported(edev)) {
ecomp->locate = 0;
return;
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
desc = ses_get_page2_descriptor(edev, ecomp);
if (desc)
ecomp->locate = (desc[2] & 0x02) ? 1 : 0;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
static int ses_set_locate(struct enclosure_device *edev,
struct enclosure_component *ecomp,
enum enclosure_component_setting val)
{
unsigned char desc[4];
unsigned char *desc_ptr;
if (!ses_page2_supported(edev))
return -EINVAL;
desc_ptr = ses_get_page2_descriptor(edev, ecomp);
if (!desc_ptr)
return -EIO;
init_device_slot_control(desc, ecomp, desc_ptr);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
switch (val) {
case ENCLOSURE_SETTING_DISABLED:
desc[2] &= 0xfd;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
break;
case ENCLOSURE_SETTING_ENABLED:
desc[2] |= 0x02;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
break;
default:
/* SES doesn't do the SGPIO blink settings */
return -EINVAL;
}
return ses_set_page2_descriptor(edev, ecomp, desc);
}
static int ses_set_active(struct enclosure_device *edev,
struct enclosure_component *ecomp,
enum enclosure_component_setting val)
{
unsigned char desc[4];
unsigned char *desc_ptr;
if (!ses_page2_supported(edev))
return -EINVAL;
desc_ptr = ses_get_page2_descriptor(edev, ecomp);
if (!desc_ptr)
return -EIO;
init_device_slot_control(desc, ecomp, desc_ptr);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
switch (val) {
case ENCLOSURE_SETTING_DISABLED:
desc[2] &= 0x7f;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
ecomp->active = 0;
break;
case ENCLOSURE_SETTING_ENABLED:
desc[2] |= 0x80;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
ecomp->active = 1;
break;
default:
/* SES doesn't do the SGPIO blink settings */
return -EINVAL;
}
return ses_set_page2_descriptor(edev, ecomp, desc);
}
static int ses_show_id(struct enclosure_device *edev, char *buf)
{
struct ses_device *ses_dev = edev->scratch;
unsigned long long id = get_unaligned_be64(ses_dev->page1+8+4);
return sprintf(buf, "%#llx\n", id);
}
static void ses_get_power_status(struct enclosure_device *edev,
struct enclosure_component *ecomp)
{
unsigned char *desc;
if (!ses_page2_supported(edev)) {
ecomp->power_status = 0;
return;
}
desc = ses_get_page2_descriptor(edev, ecomp);
if (desc)
ecomp->power_status = (desc[3] & 0x10) ? 0 : 1;
}
static int ses_set_power_status(struct enclosure_device *edev,
struct enclosure_component *ecomp,
int val)
{
unsigned char desc[4];
unsigned char *desc_ptr;
if (!ses_page2_supported(edev))
return -EINVAL;
desc_ptr = ses_get_page2_descriptor(edev, ecomp);
if (!desc_ptr)
return -EIO;
init_device_slot_control(desc, ecomp, desc_ptr);
switch (val) {
/* power = 1 is device_off = 0 and vice versa */
case 0:
desc[3] |= 0x10;
break;
case 1:
desc[3] &= 0xef;
break;
default:
return -EINVAL;
}
ecomp->power_status = val;
return ses_set_page2_descriptor(edev, ecomp, desc);
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
static struct enclosure_component_callbacks ses_enclosure_callbacks = {
.get_fault = ses_get_fault,
.set_fault = ses_set_fault,
.get_status = ses_get_status,
.get_locate = ses_get_locate,
.set_locate = ses_set_locate,
.get_power_status = ses_get_power_status,
.set_power_status = ses_set_power_status,
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
.set_active = ses_set_active,
.show_id = ses_show_id,
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
};
struct ses_host_edev {
struct Scsi_Host *shost;
struct enclosure_device *edev;
};
#if 0
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
int ses_match_host(struct enclosure_device *edev, void *data)
{
struct ses_host_edev *sed = data;
struct scsi_device *sdev;
if (!scsi_is_sdev_device(edev->edev.parent))
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
return 0;
sdev = to_scsi_device(edev->edev.parent);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (sdev->host != sed->shost)
return 0;
sed->edev = edev;
return 1;
}
#endif /* 0 */
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
static int ses_process_descriptor(struct enclosure_component *ecomp,
unsigned char *desc, int max_desc_len)
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
{
int eip = desc[0] & 0x10;
int invalid = desc[0] & 0x80;
enum scsi_protocol proto = desc[0] & 0x0f;
u64 addr = 0;
int slot = -1;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct ses_component *scomp = ecomp->scratch;
unsigned char *d;
if (invalid)
return 0;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
switch (proto) {
case SCSI_PROTOCOL_FCP:
if (eip) {
if (max_desc_len <= 7)
return 1;
d = desc + 4;
slot = d[3];
}
break;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
case SCSI_PROTOCOL_SAS:
if (eip) {
if (max_desc_len <= 27)
return 1;
d = desc + 4;
slot = d[3];
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
d = desc + 8;
} else {
if (max_desc_len <= 23)
return 1;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
d = desc + 4;
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
/* only take the phy0 addr */
addr = (u64)d[12] << 56 |
(u64)d[13] << 48 |
(u64)d[14] << 40 |
(u64)d[15] << 32 |
(u64)d[16] << 24 |
(u64)d[17] << 16 |
(u64)d[18] << 8 |
(u64)d[19];
break;
default:
/* FIXME: Need to add more protocols than just SAS */
break;
}
ecomp->slot = slot;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
scomp->addr = addr;
return 0;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
struct efd {
u64 addr;
struct device *dev;
};
static int ses_enclosure_find_by_addr(struct enclosure_device *edev,
void *data)
{
struct efd *efd = data;
int i;
struct ses_component *scomp;
for (i = 0; i < edev->components; i++) {
scomp = edev->component[i].scratch;
if (scomp->addr != efd->addr)
continue;
if (enclosure_add_device(edev, i, efd->dev) == 0)
kobject_uevent(&efd->dev->kobj, KOBJ_CHANGE);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
return 1;
}
return 0;
}
#define INIT_ALLOC_SIZE 32
static void ses_enclosure_data_process(struct enclosure_device *edev,
struct scsi_device *sdev,
int create)
{
u32 result;
unsigned char *buf = NULL, *type_ptr, *desc_ptr, *addl_desc_ptr = NULL;
int i, j, page7_len, len, components;
struct ses_device *ses_dev = edev->scratch;
int types = ses_dev->page1_num_types;
unsigned char *hdr_buf = kzalloc(INIT_ALLOC_SIZE, GFP_KERNEL);
if (!hdr_buf)
goto simple_populate;
/* re-read page 10 */
if (ses_dev->page10)
ses_recv_diag(sdev, 10, ses_dev->page10, ses_dev->page10_len);
/* Page 7 for the descriptors is optional */
result = ses_recv_diag(sdev, 7, hdr_buf, INIT_ALLOC_SIZE);
if (result)
goto simple_populate;
page7_len = len = (hdr_buf[2] << 8) + hdr_buf[3] + 4;
/* add 1 for trailing '\0' we'll use */
buf = kzalloc(len + 1, GFP_KERNEL);
if (!buf)
goto simple_populate;
result = ses_recv_diag(sdev, 7, buf, len);
if (result) {
simple_populate:
kfree(buf);
buf = NULL;
desc_ptr = NULL;
len = 0;
page7_len = 0;
} else {
desc_ptr = buf + 8;
len = (desc_ptr[2] << 8) + desc_ptr[3];
/* skip past overall descriptor */
desc_ptr += len + 4;
}
if (ses_dev->page10 && ses_dev->page10_len > 9)
addl_desc_ptr = ses_dev->page10 + 8;
type_ptr = ses_dev->page1_types;
components = 0;
for (i = 0; i < types; i++, type_ptr += 4) {
for (j = 0; j < type_ptr[1]; j++) {
char *name = NULL;
struct enclosure_component *ecomp;
int max_desc_len;
if (desc_ptr) {
if (desc_ptr + 3 >= buf + page7_len) {
desc_ptr = NULL;
} else {
len = (desc_ptr[2] << 8) + desc_ptr[3];
desc_ptr += 4;
if (desc_ptr + len > buf + page7_len)
desc_ptr = NULL;
else {
/* Add trailing zero - pushes into
* reserved space */
desc_ptr[len] = '\0';
name = desc_ptr;
}
}
}
if (type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE ||
type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE) {
if (create)
ecomp = enclosure_component_alloc(
edev,
components++,
type_ptr[0],
name);
scsi: ses: Handle enclosure with just a primary component gracefully This reverts commit 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components") and introduces proper handling of case where there are no detected secondary components, but primary component (enumerated in num_enclosures) does exist. That fix was originally proposed by Ding Hui <dinghui@sangfor.com.cn>. Completely ignoring devices that have one primary enclosure and no secondary one results in ses_intf_add() bailing completely scsi 2:0:0:254: enclosure has no enumerated components scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such even on valid configurations with 1 primary and 0 secondary enclosures as below: # sg_ses /dev/sg0 3PARdata SES 3321 Supported diagnostic pages: Supported Diagnostic Pages [sdp] [0x0] Configuration (SES) [cf] [0x1] Short Enclosure Status (SES) [ses] [0x8] # sg_ses -p cf /dev/sg0 3PARdata SES 3321 Configuration diagnostic page: number of secondary subenclosures: 0 generation code: 0x0 enclosure descriptor list Subenclosure identifier: 0 [primary] relative ES process id: 0, number of ES processes: 1 number of type descriptor headers: 1 enclosure logical identifier (hex): 20000002ac02068d enclosure vendor: 3PARdata product: VV rev: 3321 type descriptor header and text list Element type: Unspecified, subenclosure id: 0 number of possible elements: 1 The changelog for the original fix follows ===== We can get a crash when disconnecting the iSCSI session, the call trace like this: [ffff00002a00fb70] kfree at ffff00000830e224 [ffff00002a00fba0] ses_intf_remove at ffff000001f200e4 [ffff00002a00fbd0] device_del at ffff0000086b6a98 [ffff00002a00fc50] device_unregister at ffff0000086b6d58 [ffff00002a00fc70] __scsi_remove_device at ffff00000870608c [ffff00002a00fca0] scsi_remove_device at ffff000008706134 [ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4 [ffff00002a00fd10] scsi_remove_target at ffff0000087064c0 [ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4 [ffff00002a00fdb0] process_one_work at ffff00000810f35c [ffff00002a00fe00] worker_thread at ffff00000810f648 [ffff00002a00fe70] kthread at ffff000008116e98 In ses_intf_add, components count could be 0, and kcalloc 0 size scomp, but not saved in edev->component[i].scratch In this situation, edev->component[0].scratch is an invalid pointer, when kfree it in ses_intf_remove_enclosure, a crash like above would happen The call trace also could be other random cases when kfree cannot catch the invalid pointer We should not use edev->component[] array when the components count is 0 We also need check index when use edev->component[] array in ses_enclosure_data_process ===== Reported-by: Michal Kolar <mich.k@seznam.cz> Originally-by: Ding Hui <dinghui@sangfor.com.cn> Cc: stable@vger.kernel.org Fixes: 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components") Signed-off-by: Jiri Kosina <jkosina@suse.cz> Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm Tested-by: Michal Kolar <mich.k@seznam.cz> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-04-04 19:23:42 +00:00
else if (components < edev->components)
ecomp = &edev->component[components++];
scsi: ses: Handle enclosure with just a primary component gracefully This reverts commit 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components") and introduces proper handling of case where there are no detected secondary components, but primary component (enumerated in num_enclosures) does exist. That fix was originally proposed by Ding Hui <dinghui@sangfor.com.cn>. Completely ignoring devices that have one primary enclosure and no secondary one results in ses_intf_add() bailing completely scsi 2:0:0:254: enclosure has no enumerated components scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such even on valid configurations with 1 primary and 0 secondary enclosures as below: # sg_ses /dev/sg0 3PARdata SES 3321 Supported diagnostic pages: Supported Diagnostic Pages [sdp] [0x0] Configuration (SES) [cf] [0x1] Short Enclosure Status (SES) [ses] [0x8] # sg_ses -p cf /dev/sg0 3PARdata SES 3321 Configuration diagnostic page: number of secondary subenclosures: 0 generation code: 0x0 enclosure descriptor list Subenclosure identifier: 0 [primary] relative ES process id: 0, number of ES processes: 1 number of type descriptor headers: 1 enclosure logical identifier (hex): 20000002ac02068d enclosure vendor: 3PARdata product: VV rev: 3321 type descriptor header and text list Element type: Unspecified, subenclosure id: 0 number of possible elements: 1 The changelog for the original fix follows ===== We can get a crash when disconnecting the iSCSI session, the call trace like this: [ffff00002a00fb70] kfree at ffff00000830e224 [ffff00002a00fba0] ses_intf_remove at ffff000001f200e4 [ffff00002a00fbd0] device_del at ffff0000086b6a98 [ffff00002a00fc50] device_unregister at ffff0000086b6d58 [ffff00002a00fc70] __scsi_remove_device at ffff00000870608c [ffff00002a00fca0] scsi_remove_device at ffff000008706134 [ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4 [ffff00002a00fd10] scsi_remove_target at ffff0000087064c0 [ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4 [ffff00002a00fdb0] process_one_work at ffff00000810f35c [ffff00002a00fe00] worker_thread at ffff00000810f648 [ffff00002a00fe70] kthread at ffff000008116e98 In ses_intf_add, components count could be 0, and kcalloc 0 size scomp, but not saved in edev->component[i].scratch In this situation, edev->component[0].scratch is an invalid pointer, when kfree it in ses_intf_remove_enclosure, a crash like above would happen The call trace also could be other random cases when kfree cannot catch the invalid pointer We should not use edev->component[] array when the components count is 0 We also need check index when use edev->component[] array in ses_enclosure_data_process ===== Reported-by: Michal Kolar <mich.k@seznam.cz> Originally-by: Ding Hui <dinghui@sangfor.com.cn> Cc: stable@vger.kernel.org Fixes: 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components") Signed-off-by: Jiri Kosina <jkosina@suse.cz> Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm Tested-by: Michal Kolar <mich.k@seznam.cz> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-04-04 19:23:42 +00:00
else
ecomp = ERR_PTR(-EINVAL);
if (!IS_ERR(ecomp)) {
if (addl_desc_ptr) {
max_desc_len = ses_dev->page10_len -
(addl_desc_ptr - ses_dev->page10);
if (ses_process_descriptor(ecomp,
addl_desc_ptr,
max_desc_len))
addl_desc_ptr = NULL;
}
if (create)
enclosure_component_register(
ecomp);
}
}
if (desc_ptr)
desc_ptr += len;
if (addl_desc_ptr &&
/* only find additional descriptions for specific devices */
(type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE ||
type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE ||
type_ptr[0] == ENCLOSURE_COMPONENT_SAS_EXPANDER ||
/* these elements are optional */
type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_TARGET_PORT ||
type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_INITIATOR_PORT ||
type_ptr[0] == ENCLOSURE_COMPONENT_CONTROLLER_ELECTRONICS)) {
addl_desc_ptr += addl_desc_ptr[1] + 2;
if (addl_desc_ptr + 1 >= ses_dev->page10 + ses_dev->page10_len)
addl_desc_ptr = NULL;
}
}
}
kfree(buf);
kfree(hdr_buf);
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
static void ses_match_to_enclosure(struct enclosure_device *edev,
struct scsi_device *sdev,
int refresh)
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
{
struct scsi_device *edev_sdev = to_scsi_device(edev->edev.parent);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct efd efd = {
.addr = 0,
};
if (refresh)
ses_enclosure_data_process(edev, edev_sdev, 0);
if (scsi_is_sas_rphy(sdev->sdev_target->dev.parent))
efd.addr = sas_get_address(sdev);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (efd.addr) {
efd.dev = &sdev->sdev_gendev;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
enclosure_for_each_device(ses_enclosure_find_by_addr, &efd);
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
driver core: class: remove struct class_interface * from callbacks The add_dev and remove_dev callbacks in struct class_interface currently pass in a pointer back to the class_interface structure that is calling them, but none of the callback implementations actually use this pointer as it is pointless (the structure is known, the driver passed it in in the first place if it is really needed again.) So clean this up and just remove the pointer from the callbacks and fix up all callback functions. Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com> Cc: Jon Mason <jdmason@kudzu.us> Cc: Dave Jiang <dave.jiang@intel.com> Cc: Allen Hubbe <allenbh@gmail.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Doug Gilbert <dgilbert@interlog.com> Cc: John Stultz <jstultz@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Wang Weiyang <wangweiyang2@huawei.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: Jakob Koschel <jakobkoschel@gmail.com> Cc: Cai Xinchen <caixinchen1@huawei.com> Acked-by: Rafael J. Wysocki <rafael@kernel.org> Acked-by: Logan Gunthorpe <logang@deltatee.com> Link: https://lore.kernel.org/r/2023040250-pushover-platter-509c@gregkh Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-02 17:58:49 +00:00
static int ses_intf_add(struct device *cdev)
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
{
struct scsi_device *sdev = to_scsi_device(cdev->parent);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct scsi_device *tmp_sdev;
unsigned char *buf = NULL, *hdr_buf, *type_ptr, page;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct ses_device *ses_dev;
u32 result;
int i, types, len, components = 0;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
int err = -ENOMEM;
int num_enclosures;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
struct enclosure_device *edev;
struct ses_component *scomp = NULL;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (!scsi_device_enclosure(sdev)) {
/* not an enclosure, but might be in one */
struct enclosure_device *prev = NULL;
while ((edev = enclosure_find(&sdev->host->shost_gendev, prev)) != NULL) {
ses_match_to_enclosure(edev, sdev, 1);
prev = edev;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
return -ENODEV;
}
/* TYPE_ENCLOSURE prints a message in probe */
if (sdev->type != TYPE_ENCLOSURE)
sdev_printk(KERN_NOTICE, sdev, "Embedded Enclosure Device\n");
ses_dev = kzalloc(sizeof(*ses_dev), GFP_KERNEL);
hdr_buf = kzalloc(INIT_ALLOC_SIZE, GFP_KERNEL);
if (!hdr_buf || !ses_dev)
goto err_init_free;
page = 1;
result = ses_recv_diag(sdev, page, hdr_buf, INIT_ALLOC_SIZE);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (result)
goto recv_failed;
len = (hdr_buf[2] << 8) + hdr_buf[3] + 4;
buf = kzalloc(len, GFP_KERNEL);
if (!buf)
goto err_free;
result = ses_recv_diag(sdev, page, buf, len);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (result)
goto recv_failed;
types = 0;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
/* we always have one main enclosure and the rest are referred
* to as secondary subenclosures */
num_enclosures = buf[1] + 1;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
/* begin at the enclosure descriptor */
type_ptr = buf + 8;
/* skip all the enclosure descriptors */
for (i = 0; i < num_enclosures && type_ptr < buf + len; i++) {
types += type_ptr[2];
type_ptr += type_ptr[3] + 4;
}
ses_dev->page1_types = type_ptr;
ses_dev->page1_num_types = types;
for (i = 0; i < types && type_ptr < buf + len; i++, type_ptr += 4) {
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE ||
type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE)
components += type_ptr[1];
}
ses_dev->page1 = buf;
ses_dev->page1_len = len;
buf = NULL;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
page = 2;
result = ses_recv_diag(sdev, page, hdr_buf, INIT_ALLOC_SIZE);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (result)
goto page2_not_supported;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
len = (hdr_buf[2] << 8) + hdr_buf[3] + 4;
buf = kzalloc(len, GFP_KERNEL);
if (!buf)
goto err_free;
/* make sure getting page 2 actually works */
result = ses_recv_diag(sdev, 2, buf, len);
if (result)
goto recv_failed;
ses_dev->page2 = buf;
ses_dev->page2_len = len;
buf = NULL;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
/* The additional information page --- allows us
* to match up the devices */
page = 10;
result = ses_recv_diag(sdev, page, hdr_buf, INIT_ALLOC_SIZE);
if (!result) {
len = (hdr_buf[2] << 8) + hdr_buf[3] + 4;
buf = kzalloc(len, GFP_KERNEL);
if (!buf)
goto err_free;
result = ses_recv_diag(sdev, page, buf, len);
if (result)
goto recv_failed;
ses_dev->page10 = buf;
ses_dev->page10_len = len;
buf = NULL;
}
page2_not_supported:
scsi: ses: Handle enclosure with just a primary component gracefully This reverts commit 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components") and introduces proper handling of case where there are no detected secondary components, but primary component (enumerated in num_enclosures) does exist. That fix was originally proposed by Ding Hui <dinghui@sangfor.com.cn>. Completely ignoring devices that have one primary enclosure and no secondary one results in ses_intf_add() bailing completely scsi 2:0:0:254: enclosure has no enumerated components scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such even on valid configurations with 1 primary and 0 secondary enclosures as below: # sg_ses /dev/sg0 3PARdata SES 3321 Supported diagnostic pages: Supported Diagnostic Pages [sdp] [0x0] Configuration (SES) [cf] [0x1] Short Enclosure Status (SES) [ses] [0x8] # sg_ses -p cf /dev/sg0 3PARdata SES 3321 Configuration diagnostic page: number of secondary subenclosures: 0 generation code: 0x0 enclosure descriptor list Subenclosure identifier: 0 [primary] relative ES process id: 0, number of ES processes: 1 number of type descriptor headers: 1 enclosure logical identifier (hex): 20000002ac02068d enclosure vendor: 3PARdata product: VV rev: 3321 type descriptor header and text list Element type: Unspecified, subenclosure id: 0 number of possible elements: 1 The changelog for the original fix follows ===== We can get a crash when disconnecting the iSCSI session, the call trace like this: [ffff00002a00fb70] kfree at ffff00000830e224 [ffff00002a00fba0] ses_intf_remove at ffff000001f200e4 [ffff00002a00fbd0] device_del at ffff0000086b6a98 [ffff00002a00fc50] device_unregister at ffff0000086b6d58 [ffff00002a00fc70] __scsi_remove_device at ffff00000870608c [ffff00002a00fca0] scsi_remove_device at ffff000008706134 [ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4 [ffff00002a00fd10] scsi_remove_target at ffff0000087064c0 [ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4 [ffff00002a00fdb0] process_one_work at ffff00000810f35c [ffff00002a00fe00] worker_thread at ffff00000810f648 [ffff00002a00fe70] kthread at ffff000008116e98 In ses_intf_add, components count could be 0, and kcalloc 0 size scomp, but not saved in edev->component[i].scratch In this situation, edev->component[0].scratch is an invalid pointer, when kfree it in ses_intf_remove_enclosure, a crash like above would happen The call trace also could be other random cases when kfree cannot catch the invalid pointer We should not use edev->component[] array when the components count is 0 We also need check index when use edev->component[] array in ses_enclosure_data_process ===== Reported-by: Michal Kolar <mich.k@seznam.cz> Originally-by: Ding Hui <dinghui@sangfor.com.cn> Cc: stable@vger.kernel.org Fixes: 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components") Signed-off-by: Jiri Kosina <jkosina@suse.cz> Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm Tested-by: Michal Kolar <mich.k@seznam.cz> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-04-04 19:23:42 +00:00
if (components > 0) {
scomp = kcalloc(components, sizeof(struct ses_component), GFP_KERNEL);
if (!scomp)
goto err_free;
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
edev = enclosure_register(cdev->parent, dev_name(&sdev->sdev_gendev),
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
components, &ses_enclosure_callbacks);
if (IS_ERR(edev)) {
err = PTR_ERR(edev);
goto err_free;
}
kfree(hdr_buf);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
edev->scratch = ses_dev;
for (i = 0; i < components; i++)
edev->component[i].scratch = scomp + i;
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
ses_enclosure_data_process(edev, sdev, 1);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
/* see if there are any devices matching before
* we found the enclosure */
shost_for_each_device(tmp_sdev, sdev->host) {
if (tmp_sdev->lun != 0 || scsi_device_enclosure(tmp_sdev))
continue;
ses_match_to_enclosure(edev, tmp_sdev, 0);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
return 0;
recv_failed:
sdev_printk(KERN_ERR, sdev, "Failed to get diagnostic page 0x%x\n",
page);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
err = -ENODEV;
err_free:
kfree(buf);
kfree(scomp);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
kfree(ses_dev->page10);
kfree(ses_dev->page2);
kfree(ses_dev->page1);
err_init_free:
kfree(ses_dev);
kfree(hdr_buf);
sdev_printk(KERN_ERR, sdev, "Failed to bind enclosure %d\n", err);
return err;
}
static int ses_remove(struct device *dev)
{
return 0;
}
static void ses_intf_remove_component(struct scsi_device *sdev)
{
struct enclosure_device *edev, *prev = NULL;
while ((edev = enclosure_find(&sdev->host->shost_gendev, prev)) != NULL) {
prev = edev;
if (!enclosure_remove_device(edev, &sdev->sdev_gendev))
break;
}
if (edev)
put_device(&edev->edev);
}
static void ses_intf_remove_enclosure(struct scsi_device *sdev)
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
{
struct enclosure_device *edev;
struct ses_device *ses_dev;
/* exact match to this enclosure */
edev = enclosure_find(&sdev->sdev_gendev, NULL);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
if (!edev)
return;
ses_dev = edev->scratch;
edev->scratch = NULL;
kfree(ses_dev->page10);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
kfree(ses_dev->page1);
kfree(ses_dev->page2);
kfree(ses_dev);
if (edev->components)
kfree(edev->component[0].scratch);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
put_device(&edev->edev);
enclosure_unregister(edev);
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
}
driver core: class: remove struct class_interface * from callbacks The add_dev and remove_dev callbacks in struct class_interface currently pass in a pointer back to the class_interface structure that is calling them, but none of the callback implementations actually use this pointer as it is pointless (the structure is known, the driver passed it in in the first place if it is really needed again.) So clean this up and just remove the pointer from the callbacks and fix up all callback functions. Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com> Cc: Jon Mason <jdmason@kudzu.us> Cc: Dave Jiang <dave.jiang@intel.com> Cc: Allen Hubbe <allenbh@gmail.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Alexandre Bounine <alex.bou9@gmail.com> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Doug Gilbert <dgilbert@interlog.com> Cc: John Stultz <jstultz@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Wang Weiyang <wangweiyang2@huawei.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: Jakob Koschel <jakobkoschel@gmail.com> Cc: Cai Xinchen <caixinchen1@huawei.com> Acked-by: Rafael J. Wysocki <rafael@kernel.org> Acked-by: Logan Gunthorpe <logang@deltatee.com> Link: https://lore.kernel.org/r/2023040250-pushover-platter-509c@gregkh Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-02 17:58:49 +00:00
static void ses_intf_remove(struct device *cdev)
{
struct scsi_device *sdev = to_scsi_device(cdev->parent);
if (!scsi_device_enclosure(sdev))
ses_intf_remove_component(sdev);
else
ses_intf_remove_enclosure(sdev);
}
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
static struct class_interface ses_interface = {
.add_dev = ses_intf_add,
.remove_dev = ses_intf_remove,
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
};
static struct scsi_driver ses_template = {
.gendrv = {
.name = "ses",
.owner = THIS_MODULE,
[SCSI] ses: add new Enclosure ULD This adds support to SCSI for enclosure services devices. It also makes use of the enclosure services added in an earlier patch to display the enclosure topology in sysfs. At the moment, the enclosures are SAS specific, but if anyone actually has a non-SAS enclosure that follows the SES-2 standard, we can add that as well. On my Vitesse based system, the enclosures show up like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/ total 0 -r--r--r-- 1 root root 4096 2008-02-03 15:44 components lrwxrwxrwx 1 root root 0 2008-02-03 15:44 device -> ../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:1/0:0:1:0 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 000 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 001 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 002 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 003 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 004 drwxr-xr-x 2 root root 0 2008-02-03 15:44 SLOT 005 lrwxrwxrwx 1 root root 0 2008-02-03 15:44 subsystem -> ../../enclosure --w------- 1 root root 4096 2008-02-03 15:44 uevent And the individual occupied slots like this: sparkweed:~# ls -l /sys/class/enclosure/0\:0\:1\:0/SLOT\ 001/ total 0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 active lrwxrwxrwx 1 root root 0 2008-02-03 15:45 device -> ../../../../devices/pci0000:01/0000:01:02.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:0/0:0:0:0 -rw-r--r-- 1 root root 4096 2008-02-03 15:45 fault -rw-r--r-- 1 root root 4096 2008-02-03 15:45 locate -rw-r--r-- 1 root root 4096 2008-02-03 15:45 status lrwxrwxrwx 1 root root 0 2008-02-03 15:45 subsystem -> ../../../enclosure_component -r--r--r-- 1 root root 4096 2008-02-03 15:45 type --w------- 1 root root 4096 2008-02-03 15:45 uevent You can flash the various blinky lights by echoing to the fault and locate files. >From the device's point of view, you can see it has an enclosure like this: sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/ block:sda generic queue_depth state bsg:0:0:0:0 iocounterbits queue_type subsystem bus iodone_cnt rescan timeout delete ioerr_cnt rev type device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent driver modalias scsi_disk:0:0:0:0 vendor enclosure_component:SLOT 001 model scsi_generic:sg0 evt_media_change power scsi_level Note the enclosure_component:SLOT 001 which shows where in the enclosure this device fits. The astute will notice that I'm using SCSI VPD Inquiries to identify the devices. This, unfortunately, won't work for SATA devices unless we do some really nasty hacking about on the SAT because the only think that knows the SAS addresses for SATA devices is libsas, not libata where the SAT resides. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-03 21:48:56 +00:00
.probe = ses_probe,
.remove = ses_remove,
},
};
static int __init ses_init(void)
{
int err;
err = scsi_register_interface(&ses_interface);
if (err)
return err;
err = scsi_register_driver(&ses_template.gendrv);
if (err)
goto out_unreg;
return 0;
out_unreg:
scsi_unregister_interface(&ses_interface);
return err;
}
static void __exit ses_exit(void)
{
scsi_unregister_driver(&ses_template.gendrv);
scsi_unregister_interface(&ses_interface);
}
module_init(ses_init);
module_exit(ses_exit);
MODULE_ALIAS_SCSI_DEVICE(TYPE_ENCLOSURE);
MODULE_AUTHOR("James Bottomley");
MODULE_DESCRIPTION("SCSI Enclosure Services (ses) driver");
MODULE_LICENSE("GPL v2");