linux-stable/drivers/thermal/step_wise.c

231 lines
6.7 KiB
C
Raw Normal View History

/*
* step_wise.c - A step-by-step Thermal throttling governor
*
* Copyright (C) 2012 Intel Corp
* Copyright (C) 2012 Durgadoss R <durgadoss.r@intel.com>
*
* ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
*
* ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
*/
#include <linux/thermal.h>
#include <trace/events/thermal.h>
#include "thermal_core.h"
/*
* If the temperature is higher than a trip point,
* a. if the trend is THERMAL_TREND_RAISING, use higher cooling
* state for this trip point
thermal/drivers/step_wise: Fix temperature regulation misbehavior There is a particular situation when the cooling device is cpufreq and the heat dissipation is not efficient enough where the temperature increases little by little until reaching the critical threshold and leading to a SoC reset. The behavior is reproducible on a hikey6220 with bad heat dissipation (eg. stacked with other boards). Running a simple C program doing while(1); for each CPU of the SoC makes the temperature to reach the passive regulation trip point and ends up to the maximum allowed temperature followed by a reset. This issue has been also reported by running the libhugetlbfs test suite. What is observed is a ping pong between two cpu frequencies, 1.2GHz and 900MHz while the temperature continues to grow. It appears the step wise governor calls get_target_state() the first time with the throttle set to true and the trend to 'raising'. The code selects logically the next state, so the cpu frequency decreases from 1.2GHz to 900MHz, so far so good. The temperature decreases immediately but still stays greater than the trip point, then get_target_state() is called again, this time with the throttle set to true *and* the trend to 'dropping'. From there the algorithm assumes we have to step down the state and the cpu frequency jumps back to 1.2GHz. But the temperature is still higher than the trip point, so get_target_state() is called with throttle=1 and trend='raising' again, we jump to 900MHz, then get_target_state() is called with throttle=1 and trend='dropping', we jump to 1.2GHz, etc ... but the temperature does not stabilizes and continues to increase. [ 237.922654] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 237.922678] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 237.922690] thermal cooling_device0: cur_state=0 [ 237.922701] thermal cooling_device0: old_target=0, target=1 [ 238.026656] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 238.026680] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1 [ 238.026694] thermal cooling_device0: cur_state=1 [ 238.026707] thermal cooling_device0: old_target=1, target=0 [ 238.134647] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 238.134667] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 238.134679] thermal cooling_device0: cur_state=0 [ 238.134690] thermal cooling_device0: old_target=0, target=1 In this situation the temperature continues to increase while the trend is oscillating between 'dropping' and 'raising'. We need to keep the current state untouched if the throttle is set, so the temperature can decrease or a higher state could be selected, thus preventing this oscillation. Keeping the next_target untouched when 'throttle' is true at 'dropping' time fixes the issue. The following traces show the governor does not change the next state if trend==2 (dropping) and throttle==1. [ 2306.127987] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2306.128009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 2306.128021] thermal cooling_device0: cur_state=0 [ 2306.128031] thermal cooling_device0: old_target=0, target=1 [ 2306.231991] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2306.232016] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1 [ 2306.232030] thermal cooling_device0: cur_state=1 [ 2306.232042] thermal cooling_device0: old_target=1, target=1 [ 2306.335982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2306.336006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=1 [ 2306.336021] thermal cooling_device0: cur_state=1 [ 2306.336034] thermal cooling_device0: old_target=1, target=1 [ 2306.439984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2306.440008] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0 [ 2306.440022] thermal cooling_device0: cur_state=1 [ 2306.440034] thermal cooling_device0: old_target=1, target=0 [ ... ] After a while, if the temperature continues to increase, the next state becomes 2 which is 720MHz on the hikey. That results in the temperature stabilizing around the trip point. [ 2455.831982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2455.832006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=0 [ 2455.832019] thermal cooling_device0: cur_state=1 [ 2455.832032] thermal cooling_device0: old_target=1, target=1 [ 2455.935985] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2455.936013] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0 [ 2455.936027] thermal cooling_device0: cur_state=1 [ 2455.936040] thermal cooling_device0: old_target=1, target=1 [ 2456.043984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2456.044009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0 [ 2456.044023] thermal cooling_device0: cur_state=1 [ 2456.044036] thermal cooling_device0: old_target=1, target=1 [ 2456.148001] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2456.148028] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 2456.148042] thermal cooling_device0: cur_state=1 [ 2456.148055] thermal cooling_device0: old_target=1, target=2 [ 2456.252009] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2456.252041] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0 [ 2456.252058] thermal cooling_device0: cur_state=2 [ 2456.252075] thermal cooling_device0: old_target=2, target=1 IOW, this change is needed to keep the state for a cooling device if the temperature trend is oscillating while the temperature increases slightly. Without this change, the situation above leads to a catastrophic crash by a hardware reset on hikey. This issue has been reported to happen on an OMAP dra7xx also. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2017-10-19 17:05:58 +00:00
* b. if the trend is THERMAL_TREND_DROPPING, do nothing
* c. if the trend is THERMAL_TREND_RAISE_FULL, use upper limit
* for this trip point
* d. if the trend is THERMAL_TREND_DROP_FULL, use lower limit
* for this trip point
* If the temperature is lower than a trip point,
* a. if the trend is THERMAL_TREND_RAISING, do nothing
* b. if the trend is THERMAL_TREND_DROPPING, use lower cooling
* state for this trip point, if the cooling state already
* equals lower limit, deactivate the thermal instance
* c. if the trend is THERMAL_TREND_RAISE_FULL, do nothing
* d. if the trend is THERMAL_TREND_DROP_FULL, use lower limit,
* if the cooling state already equals lower limit,
* deactivate the thermal instance
*/
static unsigned long get_target_state(struct thermal_instance *instance,
enum thermal_trend trend, bool throttle)
{
struct thermal_cooling_device *cdev = instance->cdev;
unsigned long cur_state;
unsigned long next_target;
/*
* We keep this instance the way it is by default.
* Otherwise, we use the current state of the
* cdev in use to determine the next_target.
*/
cdev->ops->get_cur_state(cdev, &cur_state);
next_target = instance->target;
thermal: debug: add debug statement for core and step_wise To ease debugging thermal problem, add these dynamic debug statements so that user do not need rebuild kernel to see these info. Based on a patch from Zhang Rui for debugging on bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=98671 A sample output after we turn on dynamic debug with the following cmd: # echo 'module thermal_sys +fp' > /sys/kernel/debug/dynamic_debug/control is like: [ 355.147627] update_temperature: thermal thermal_zone0: last_temperature=52000, current_temperature=55000 [ 355.147636] thermal_zone_trip_update: thermal thermal_zone0: Trip1[type=1,temp=79000]:trend=2,throttle=0 [ 355.147644] get_target_state: thermal cooling_device8: cur_state=0 [ 355.147647] thermal_zone_trip_update: thermal cooling_device8: old_target=-1, target=-1 [ 355.147652] get_target_state: thermal cooling_device7: cur_state=0 [ 355.147655] thermal_zone_trip_update: thermal cooling_device7: old_target=-1, target=-1 [ 355.147660] get_target_state: thermal cooling_device6: cur_state=0 [ 355.147663] thermal_zone_trip_update: thermal cooling_device6: old_target=-1, target=-1 [ 355.147668] get_target_state: thermal cooling_device5: cur_state=0 [ 355.147671] thermal_zone_trip_update: thermal cooling_device5: old_target=-1, target=-1 [ 355.147678] thermal_zone_trip_update: thermal thermal_zone0: Trip2[type=0,temp=90000]:trend=1,throttle=0 [ 355.147776] get_target_state: thermal cooling_device0: cur_state=0 [ 355.147783] thermal_zone_trip_update: thermal cooling_device0: old_target=-1, target=-1 [ 355.147792] thermal_zone_trip_update: thermal thermal_zone0: Trip3[type=0,temp=80000]:trend=1,throttle=0 [ 355.147845] get_target_state: thermal cooling_device1: cur_state=0 [ 355.147849] thermal_zone_trip_update: thermal cooling_device1: old_target=-1, target=-1 [ 355.147856] thermal_zone_trip_update: thermal thermal_zone0: Trip4[type=0,temp=70000]:trend=1,throttle=0 [ 355.147904] get_target_state: thermal cooling_device2: cur_state=0 [ 355.147908] thermal_zone_trip_update: thermal cooling_device2: old_target=-1, target=-1 [ 355.147915] thermal_zone_trip_update: thermal thermal_zone0: Trip5[type=0,temp=60000]:trend=1,throttle=0 [ 355.147963] get_target_state: thermal cooling_device3: cur_state=0 [ 355.147967] thermal_zone_trip_update: thermal cooling_device3: old_target=-1, target=-1 [ 355.147973] thermal_zone_trip_update: thermal thermal_zone0: Trip6[type=0,temp=55000]:trend=1,throttle=1 [ 355.148022] get_target_state: thermal cooling_device4: cur_state=0 [ 355.148025] thermal_zone_trip_update: thermal cooling_device4: old_target=-1, target=1 [ 355.148036] thermal_cdev_update: thermal cooling_device4: zone0->target=1 [ 355.169279] thermal_cdev_update: thermal cooling_device4: set to state 1 Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Eduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2013-12-02 05:54:26 +00:00
dev_dbg(&cdev->device, "cur_state=%ld\n", cur_state);
if (!instance->initialized) {
if (throttle) {
next_target = (cur_state + 1) >= instance->upper ?
instance->upper :
((cur_state + 1) < instance->lower ?
instance->lower : (cur_state + 1));
} else {
next_target = THERMAL_NO_TARGET;
}
return next_target;
}
switch (trend) {
case THERMAL_TREND_RAISING:
if (throttle) {
next_target = cur_state < instance->upper ?
(cur_state + 1) : instance->upper;
if (next_target < instance->lower)
next_target = instance->lower;
}
break;
case THERMAL_TREND_RAISE_FULL:
if (throttle)
next_target = instance->upper;
break;
case THERMAL_TREND_DROPPING:
if (cur_state <= instance->lower) {
if (!throttle)
next_target = THERMAL_NO_TARGET;
} else {
thermal/drivers/step_wise: Fix temperature regulation misbehavior There is a particular situation when the cooling device is cpufreq and the heat dissipation is not efficient enough where the temperature increases little by little until reaching the critical threshold and leading to a SoC reset. The behavior is reproducible on a hikey6220 with bad heat dissipation (eg. stacked with other boards). Running a simple C program doing while(1); for each CPU of the SoC makes the temperature to reach the passive regulation trip point and ends up to the maximum allowed temperature followed by a reset. This issue has been also reported by running the libhugetlbfs test suite. What is observed is a ping pong between two cpu frequencies, 1.2GHz and 900MHz while the temperature continues to grow. It appears the step wise governor calls get_target_state() the first time with the throttle set to true and the trend to 'raising'. The code selects logically the next state, so the cpu frequency decreases from 1.2GHz to 900MHz, so far so good. The temperature decreases immediately but still stays greater than the trip point, then get_target_state() is called again, this time with the throttle set to true *and* the trend to 'dropping'. From there the algorithm assumes we have to step down the state and the cpu frequency jumps back to 1.2GHz. But the temperature is still higher than the trip point, so get_target_state() is called with throttle=1 and trend='raising' again, we jump to 900MHz, then get_target_state() is called with throttle=1 and trend='dropping', we jump to 1.2GHz, etc ... but the temperature does not stabilizes and continues to increase. [ 237.922654] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 237.922678] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 237.922690] thermal cooling_device0: cur_state=0 [ 237.922701] thermal cooling_device0: old_target=0, target=1 [ 238.026656] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 238.026680] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1 [ 238.026694] thermal cooling_device0: cur_state=1 [ 238.026707] thermal cooling_device0: old_target=1, target=0 [ 238.134647] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 238.134667] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 238.134679] thermal cooling_device0: cur_state=0 [ 238.134690] thermal cooling_device0: old_target=0, target=1 In this situation the temperature continues to increase while the trend is oscillating between 'dropping' and 'raising'. We need to keep the current state untouched if the throttle is set, so the temperature can decrease or a higher state could be selected, thus preventing this oscillation. Keeping the next_target untouched when 'throttle' is true at 'dropping' time fixes the issue. The following traces show the governor does not change the next state if trend==2 (dropping) and throttle==1. [ 2306.127987] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2306.128009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 2306.128021] thermal cooling_device0: cur_state=0 [ 2306.128031] thermal cooling_device0: old_target=0, target=1 [ 2306.231991] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2306.232016] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1 [ 2306.232030] thermal cooling_device0: cur_state=1 [ 2306.232042] thermal cooling_device0: old_target=1, target=1 [ 2306.335982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2306.336006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=1 [ 2306.336021] thermal cooling_device0: cur_state=1 [ 2306.336034] thermal cooling_device0: old_target=1, target=1 [ 2306.439984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2306.440008] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0 [ 2306.440022] thermal cooling_device0: cur_state=1 [ 2306.440034] thermal cooling_device0: old_target=1, target=0 [ ... ] After a while, if the temperature continues to increase, the next state becomes 2 which is 720MHz on the hikey. That results in the temperature stabilizing around the trip point. [ 2455.831982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2455.832006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=0 [ 2455.832019] thermal cooling_device0: cur_state=1 [ 2455.832032] thermal cooling_device0: old_target=1, target=1 [ 2455.935985] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2455.936013] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0 [ 2455.936027] thermal cooling_device0: cur_state=1 [ 2455.936040] thermal cooling_device0: old_target=1, target=1 [ 2456.043984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1 [ 2456.044009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0 [ 2456.044023] thermal cooling_device0: cur_state=1 [ 2456.044036] thermal cooling_device0: old_target=1, target=1 [ 2456.148001] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1 [ 2456.148028] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1 [ 2456.148042] thermal cooling_device0: cur_state=1 [ 2456.148055] thermal cooling_device0: old_target=1, target=2 [ 2456.252009] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1 [ 2456.252041] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0 [ 2456.252058] thermal cooling_device0: cur_state=2 [ 2456.252075] thermal cooling_device0: old_target=2, target=1 IOW, this change is needed to keep the state for a cooling device if the temperature trend is oscillating while the temperature increases slightly. Without this change, the situation above leads to a catastrophic crash by a hardware reset on hikey. This issue has been reported to happen on an OMAP dra7xx also. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2017-10-19 17:05:58 +00:00
if (!throttle) {
next_target = cur_state - 1;
if (next_target > instance->upper)
next_target = instance->upper;
}
}
break;
case THERMAL_TREND_DROP_FULL:
if (cur_state == instance->lower) {
if (!throttle)
next_target = THERMAL_NO_TARGET;
} else
next_target = instance->lower;
break;
default:
break;
}
return next_target;
}
static void update_passive_instance(struct thermal_zone_device *tz,
enum thermal_trip_type type, int value)
{
/*
* If value is +1, activate a passive instance.
* If value is -1, deactivate a passive instance.
*/
if (type == THERMAL_TRIP_PASSIVE || type == THERMAL_TRIPS_NONE)
tz->passive += value;
}
static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip)
{
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 06:12:54 +00:00
int trip_temp;
enum thermal_trip_type trip_type;
enum thermal_trend trend;
struct thermal_instance *instance;
bool throttle = false;
int old_target;
if (trip == THERMAL_TRIPS_NONE) {
trip_temp = tz->forced_passive;
trip_type = THERMAL_TRIPS_NONE;
} else {
tz->ops->get_trip_temp(tz, trip, &trip_temp);
tz->ops->get_trip_type(tz, trip, &trip_type);
}
trend = get_tz_trend(tz, trip);
if (tz->temperature >= trip_temp) {
throttle = true;
trace_thermal_zone_trip(tz, trip, trip_type);
}
thermal: consistently use int for temperatures The thermal code uses int, long and unsigned long for temperatures in different places. Using an unsigned type limits the thermal framework to positive temperatures without need. Also several drivers currently will report temperatures near UINT_MAX for temperatures below 0°C. This will probably immediately shut the machine down due to overtemperature if started below 0°C. 'long' is 64bit on several architectures. This is not needed since INT_MAX °mC is above the melting point of all known materials. Consistently use a plain 'int' for temperatures throughout the thermal code and the drivers. This only changes the places in the drivers where the temperature is passed around as pointer, when drivers internally use another type this is not changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Peter Feuerer <peter@piie.net> Cc: Punit Agrawal <punit.agrawal@arm.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Jean Delvare <jdelvare@suse.de> Cc: Peter Feuerer <peter@piie.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: linux-acpi@vger.kernel.org Cc: platform-driver-x86@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: Guenter Roeck <linux@roeck-us.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Darren Hart <dvhart@infradead.org> Cc: lm-sensors@lm-sensors.org Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2015-07-24 06:12:54 +00:00
dev_dbg(&tz->device, "Trip%d[type=%d,temp=%d]:trend=%d,throttle=%d\n",
thermal: debug: add debug statement for core and step_wise To ease debugging thermal problem, add these dynamic debug statements so that user do not need rebuild kernel to see these info. Based on a patch from Zhang Rui for debugging on bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=98671 A sample output after we turn on dynamic debug with the following cmd: # echo 'module thermal_sys +fp' > /sys/kernel/debug/dynamic_debug/control is like: [ 355.147627] update_temperature: thermal thermal_zone0: last_temperature=52000, current_temperature=55000 [ 355.147636] thermal_zone_trip_update: thermal thermal_zone0: Trip1[type=1,temp=79000]:trend=2,throttle=0 [ 355.147644] get_target_state: thermal cooling_device8: cur_state=0 [ 355.147647] thermal_zone_trip_update: thermal cooling_device8: old_target=-1, target=-1 [ 355.147652] get_target_state: thermal cooling_device7: cur_state=0 [ 355.147655] thermal_zone_trip_update: thermal cooling_device7: old_target=-1, target=-1 [ 355.147660] get_target_state: thermal cooling_device6: cur_state=0 [ 355.147663] thermal_zone_trip_update: thermal cooling_device6: old_target=-1, target=-1 [ 355.147668] get_target_state: thermal cooling_device5: cur_state=0 [ 355.147671] thermal_zone_trip_update: thermal cooling_device5: old_target=-1, target=-1 [ 355.147678] thermal_zone_trip_update: thermal thermal_zone0: Trip2[type=0,temp=90000]:trend=1,throttle=0 [ 355.147776] get_target_state: thermal cooling_device0: cur_state=0 [ 355.147783] thermal_zone_trip_update: thermal cooling_device0: old_target=-1, target=-1 [ 355.147792] thermal_zone_trip_update: thermal thermal_zone0: Trip3[type=0,temp=80000]:trend=1,throttle=0 [ 355.147845] get_target_state: thermal cooling_device1: cur_state=0 [ 355.147849] thermal_zone_trip_update: thermal cooling_device1: old_target=-1, target=-1 [ 355.147856] thermal_zone_trip_update: thermal thermal_zone0: Trip4[type=0,temp=70000]:trend=1,throttle=0 [ 355.147904] get_target_state: thermal cooling_device2: cur_state=0 [ 355.147908] thermal_zone_trip_update: thermal cooling_device2: old_target=-1, target=-1 [ 355.147915] thermal_zone_trip_update: thermal thermal_zone0: Trip5[type=0,temp=60000]:trend=1,throttle=0 [ 355.147963] get_target_state: thermal cooling_device3: cur_state=0 [ 355.147967] thermal_zone_trip_update: thermal cooling_device3: old_target=-1, target=-1 [ 355.147973] thermal_zone_trip_update: thermal thermal_zone0: Trip6[type=0,temp=55000]:trend=1,throttle=1 [ 355.148022] get_target_state: thermal cooling_device4: cur_state=0 [ 355.148025] thermal_zone_trip_update: thermal cooling_device4: old_target=-1, target=1 [ 355.148036] thermal_cdev_update: thermal cooling_device4: zone0->target=1 [ 355.169279] thermal_cdev_update: thermal cooling_device4: set to state 1 Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Eduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2013-12-02 05:54:26 +00:00
trip, trip_type, trip_temp, trend, throttle);
mutex_lock(&tz->lock);
list_for_each_entry(instance, &tz->thermal_instances, tz_node) {
if (instance->trip != trip)
continue;
old_target = instance->target;
instance->target = get_target_state(instance, trend, throttle);
thermal: debug: add debug statement for core and step_wise To ease debugging thermal problem, add these dynamic debug statements so that user do not need rebuild kernel to see these info. Based on a patch from Zhang Rui for debugging on bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=98671 A sample output after we turn on dynamic debug with the following cmd: # echo 'module thermal_sys +fp' > /sys/kernel/debug/dynamic_debug/control is like: [ 355.147627] update_temperature: thermal thermal_zone0: last_temperature=52000, current_temperature=55000 [ 355.147636] thermal_zone_trip_update: thermal thermal_zone0: Trip1[type=1,temp=79000]:trend=2,throttle=0 [ 355.147644] get_target_state: thermal cooling_device8: cur_state=0 [ 355.147647] thermal_zone_trip_update: thermal cooling_device8: old_target=-1, target=-1 [ 355.147652] get_target_state: thermal cooling_device7: cur_state=0 [ 355.147655] thermal_zone_trip_update: thermal cooling_device7: old_target=-1, target=-1 [ 355.147660] get_target_state: thermal cooling_device6: cur_state=0 [ 355.147663] thermal_zone_trip_update: thermal cooling_device6: old_target=-1, target=-1 [ 355.147668] get_target_state: thermal cooling_device5: cur_state=0 [ 355.147671] thermal_zone_trip_update: thermal cooling_device5: old_target=-1, target=-1 [ 355.147678] thermal_zone_trip_update: thermal thermal_zone0: Trip2[type=0,temp=90000]:trend=1,throttle=0 [ 355.147776] get_target_state: thermal cooling_device0: cur_state=0 [ 355.147783] thermal_zone_trip_update: thermal cooling_device0: old_target=-1, target=-1 [ 355.147792] thermal_zone_trip_update: thermal thermal_zone0: Trip3[type=0,temp=80000]:trend=1,throttle=0 [ 355.147845] get_target_state: thermal cooling_device1: cur_state=0 [ 355.147849] thermal_zone_trip_update: thermal cooling_device1: old_target=-1, target=-1 [ 355.147856] thermal_zone_trip_update: thermal thermal_zone0: Trip4[type=0,temp=70000]:trend=1,throttle=0 [ 355.147904] get_target_state: thermal cooling_device2: cur_state=0 [ 355.147908] thermal_zone_trip_update: thermal cooling_device2: old_target=-1, target=-1 [ 355.147915] thermal_zone_trip_update: thermal thermal_zone0: Trip5[type=0,temp=60000]:trend=1,throttle=0 [ 355.147963] get_target_state: thermal cooling_device3: cur_state=0 [ 355.147967] thermal_zone_trip_update: thermal cooling_device3: old_target=-1, target=-1 [ 355.147973] thermal_zone_trip_update: thermal thermal_zone0: Trip6[type=0,temp=55000]:trend=1,throttle=1 [ 355.148022] get_target_state: thermal cooling_device4: cur_state=0 [ 355.148025] thermal_zone_trip_update: thermal cooling_device4: old_target=-1, target=1 [ 355.148036] thermal_cdev_update: thermal cooling_device4: zone0->target=1 [ 355.169279] thermal_cdev_update: thermal cooling_device4: set to state 1 Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Eduardo Valentin <eduardo.valentin@ti.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2013-12-02 05:54:26 +00:00
dev_dbg(&instance->cdev->device, "old_target=%d, target=%d\n",
old_target, (int)instance->target);
if (instance->initialized && old_target == instance->target)
continue;
/* Activate a passive thermal instance */
if (old_target == THERMAL_NO_TARGET &&
instance->target != THERMAL_NO_TARGET)
update_passive_instance(tz, trip_type, 1);
/* Deactivate a passive thermal instance */
else if (old_target != THERMAL_NO_TARGET &&
instance->target == THERMAL_NO_TARGET)
update_passive_instance(tz, trip_type, -1);
instance->initialized = true;
thermal: fix race condition when updating cooling device When multiple thermal zones are bound to the same cooling device, multiple kernel threads may want to update the cooling device state by calling thermal_cdev_update(). Having cdev not protected by a mutex can lead to a race condition. Consider the following situation with two kernel threads k1 and k2: Thread k1 Thread k2 || || call thermal_cdev_update() || ... || set_cur_state(cdev, target); call power_actor_set_power() || ... || instance->target = state; || cdev->updated = false; || || cdev->updated = true; || // completes execution call thermal_cdev_update() || // cdev->updated == true || return; || \/ time k2 has already looped through the thermal instances looking for the deepest cooling device state and is preempted right before setting cdev->updated to true. Now, k1 runs, modifies the thermal instance state and sets cdev->updated to false. Then, k1 is preempted and k2 continues the execution by setting cdev->updated to true, therefore preventing k1 from performing the update. Notice that this is not an issue if k2 looks at the instance->target modified by k1 "after" it is assigned by k1. In fact, in this case the update will happen anyway and k1 can safely return immediately from thermal_cdev_update(). This may lead to a situation where a thermal governor never updates the cooling device. For example, this is the case for the step_wise governor: when calling the function thermal_zone_trip_update(), the governor may always get a new state equal to the old one (which, however, wasn't notified to the cooling device) and will therefore skip the update. CC: Zhang Rui <rui.zhang@intel.com> CC: Eduardo Valentin <edubezval@gmail.com> CC: Peter Feuerer <peter@piie.net> Reported-by: Toby Huang <toby.huang@arm.com> Signed-off-by: Michele Di Giorgio <michele.digiorgio@arm.com> Reviewed-by: Javi Merino <javi.merino@arm.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2016-06-02 14:25:31 +00:00
mutex_lock(&instance->cdev->lock);
instance->cdev->updated = false; /* cdev needs update */
thermal: fix race condition when updating cooling device When multiple thermal zones are bound to the same cooling device, multiple kernel threads may want to update the cooling device state by calling thermal_cdev_update(). Having cdev not protected by a mutex can lead to a race condition. Consider the following situation with two kernel threads k1 and k2: Thread k1 Thread k2 || || call thermal_cdev_update() || ... || set_cur_state(cdev, target); call power_actor_set_power() || ... || instance->target = state; || cdev->updated = false; || || cdev->updated = true; || // completes execution call thermal_cdev_update() || // cdev->updated == true || return; || \/ time k2 has already looped through the thermal instances looking for the deepest cooling device state and is preempted right before setting cdev->updated to true. Now, k1 runs, modifies the thermal instance state and sets cdev->updated to false. Then, k1 is preempted and k2 continues the execution by setting cdev->updated to true, therefore preventing k1 from performing the update. Notice that this is not an issue if k2 looks at the instance->target modified by k1 "after" it is assigned by k1. In fact, in this case the update will happen anyway and k1 can safely return immediately from thermal_cdev_update(). This may lead to a situation where a thermal governor never updates the cooling device. For example, this is the case for the step_wise governor: when calling the function thermal_zone_trip_update(), the governor may always get a new state equal to the old one (which, however, wasn't notified to the cooling device) and will therefore skip the update. CC: Zhang Rui <rui.zhang@intel.com> CC: Eduardo Valentin <edubezval@gmail.com> CC: Peter Feuerer <peter@piie.net> Reported-by: Toby Huang <toby.huang@arm.com> Signed-off-by: Michele Di Giorgio <michele.digiorgio@arm.com> Reviewed-by: Javi Merino <javi.merino@arm.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2016-06-02 14:25:31 +00:00
mutex_unlock(&instance->cdev->lock);
}
mutex_unlock(&tz->lock);
}
/**
* step_wise_throttle - throttles devices associated with the given zone
* @tz - thermal_zone_device
* @trip - trip point index
*
* Throttling Logic: This uses the trend of the thermal zone to throttle.
* If the thermal zone is 'heating up' this throttles all the cooling
* devices associated with the zone and its particular trip point, by one
* step. If the zone is 'cooling down' it brings back the performance of
* the devices by one step.
*/
static int step_wise_throttle(struct thermal_zone_device *tz, int trip)
{
struct thermal_instance *instance;
thermal_zone_trip_update(tz, trip);
if (tz->forced_passive)
thermal_zone_trip_update(tz, THERMAL_TRIPS_NONE);
mutex_lock(&tz->lock);
list_for_each_entry(instance, &tz->thermal_instances, tz_node)
thermal_cdev_update(instance->cdev);
mutex_unlock(&tz->lock);
return 0;
}
static struct thermal_governor thermal_gov_step_wise = {
.name = "step_wise",
.throttle = step_wise_throttle,
};
int thermal_gov_step_wise_register(void)
{
return thermal_register_governor(&thermal_gov_step_wise);
}
void thermal_gov_step_wise_unregister(void)
{
thermal_unregister_governor(&thermal_gov_step_wise);
}