linux-stable/include/linux/usb.h

2016 lines
76 KiB
C
Raw Normal View History

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 14:07:57 +00:00
/* SPDX-License-Identifier: GPL-2.0 */
#ifndef __LINUX_USB_H
#define __LINUX_USB_H
#include <linux/mod_devicetable.h>
#include <linux/usb/ch9.h>
#define USB_MAJOR 180
[PATCH] USB: real nodes instead of usbfs This patch introduces a /sys/class/usb_device/ class where every connected usb-device will show up: tree /sys/class/usb_device/ /sys/class/usb_device/ |-- usb1.1 | |-- dev | `-- device -> ../../../devices/pci0000:00/0000:00:1d.0/usb1 |-- usb2.1 | |-- dev | `-- device -> ../../../devices/pci0000:00/0000:00:1d.1/usb2 ... The presence of the "dev" file lets udev create real device nodes. kay@pim:~/src/linux-2.6> tree /dev/bus/usb/ /dev/bus/usb/ |-- 1 | `-- 1 |-- 2 | `-- 1 ... udev rule: SUBSYSTEM="usb_device", PROGRAM="/sbin/usb_device %k", NAME="%c" (echo $1 | /bin/sed 's/usb\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/') This makes libusb pick up the real nodes instead of the mounted usbfs: export USB_DEVFS_PATH=/dev/bus/usb Background: All this makes it possible to manage usb devices with udev instead of the devfs solution. We are currently working on a pam_console/resmgr replacement driven by udev and a pam-helper. It applies ACL's to device nodes, which is required for modern desktop functionalty like "Fast User Switching" or multiple local login support. New patch with its own major. I've succesfully disabled usbfs and use real nodes only on my box. With: "export USB_DEVFS_PATH=/dev/bus/usb" libusb picks up the udev managed nodes instead of reading usbfs files. This makes udev to provide symlinks for libusb to pick up: SUBSYSTEM="usb_device", PROGRAM="/sbin/usbdevice %k", SYMLINK="%c" /sbin/usbdevice: #!/bin/sh echo $1 | /bin/sed 's/usbdev\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/' Signed-off-by: Kay Sievers <kay.sievers@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-07-30 23:05:53 +00:00
#define USB_DEVICE_MAJOR 189
#ifdef __KERNEL__
#include <linux/errno.h> /* for -ENODEV */
#include <linux/delay.h> /* for mdelay() */
#include <linux/interrupt.h> /* for in_interrupt() */
#include <linux/list.h> /* for struct list_head */
#include <linux/kref.h> /* for struct kref */
#include <linux/device.h> /* for struct device */
#include <linux/fs.h> /* for struct file_operations */
#include <linux/completion.h> /* for struct completion */
#include <linux/sched.h> /* for current && schedule_timeout */
#include <linux/mutex.h> /* for struct mutex */
#include <linux/pm_runtime.h> /* for runtime PM */
struct usb_device;
struct usb_driver;
struct wusb_dev;
/*-------------------------------------------------------------------------*/
/*
* Host-side wrappers for standard USB descriptors ... these are parsed
* from the data provided by devices. Parsing turns them from a flat
* sequence of descriptors into a hierarchy:
*
* - devices have one (usually) or more configs;
* - configs have one (often) or more interfaces;
* - interfaces have one (usually) or more settings;
* - each interface setting has zero or (usually) more endpoints.
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 02:58:14 +00:00
* - a SuperSpeed endpoint has a companion descriptor
*
* And there might be other descriptors mixed in with those.
*
* Devices may also have class-specific or vendor-specific descriptors.
*/
struct ep_device;
/**
* struct usb_host_endpoint - host-side endpoint descriptor and queue
* @desc: descriptor for this endpoint, wMaxPacketSize in native byteorder
* @ss_ep_comp: SuperSpeed companion descriptor for this endpoint
* @ssp_isoc_ep_comp: SuperSpeedPlus isoc companion descriptor for this endpoint
* @urb_list: urbs queued to this endpoint; maintained by usbcore
* @hcpriv: for use by HCD; typically holds hardware dma queue head (QH)
* with one or more transfer descriptors (TDs) per urb
* @ep_dev: ep_device for sysfs info
* @extra: descriptors following this endpoint in the configuration
* @extralen: how many bytes of "extra" are valid
* @enabled: URBs may be submitted to this endpoint
* @streams: number of USB-3 streams allocated on the endpoint
*
* USB requests are always queued to a given endpoint, identified by a
* descriptor within an active interface in a given USB configuration.
*/
struct usb_host_endpoint {
struct usb_endpoint_descriptor desc;
struct usb_ss_ep_comp_descriptor ss_ep_comp;
struct usb_ssp_isoc_ep_comp_descriptor ssp_isoc_ep_comp;
struct list_head urb_list;
void *hcpriv;
struct ep_device *ep_dev; /* For sysfs info */
unsigned char *extra; /* Extra descriptors */
int extralen;
int enabled;
int streams;
};
/* host-side wrapper for one interface setting's parsed descriptors */
struct usb_host_interface {
struct usb_interface_descriptor desc;
int extralen;
unsigned char *extra; /* Extra descriptors */
/* array of desc.bNumEndpoints endpoints associated with this
* interface setting. these will be in no particular order.
*/
struct usb_host_endpoint *endpoint;
char *string; /* iInterface string, if present */
};
enum usb_interface_condition {
USB_INTERFACE_UNBOUND = 0,
USB_INTERFACE_BINDING,
USB_INTERFACE_BOUND,
USB_INTERFACE_UNBINDING,
};
int __must_check
usb_find_common_endpoints(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **bulk_in,
struct usb_endpoint_descriptor **bulk_out,
struct usb_endpoint_descriptor **int_in,
struct usb_endpoint_descriptor **int_out);
int __must_check
usb_find_common_endpoints_reverse(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **bulk_in,
struct usb_endpoint_descriptor **bulk_out,
struct usb_endpoint_descriptor **int_in,
struct usb_endpoint_descriptor **int_out);
static inline int __must_check
usb_find_bulk_in_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **bulk_in)
{
return usb_find_common_endpoints(alt, bulk_in, NULL, NULL, NULL);
}
static inline int __must_check
usb_find_bulk_out_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **bulk_out)
{
return usb_find_common_endpoints(alt, NULL, bulk_out, NULL, NULL);
}
static inline int __must_check
usb_find_int_in_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **int_in)
{
return usb_find_common_endpoints(alt, NULL, NULL, int_in, NULL);
}
static inline int __must_check
usb_find_int_out_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **int_out)
{
return usb_find_common_endpoints(alt, NULL, NULL, NULL, int_out);
}
static inline int __must_check
usb_find_last_bulk_in_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **bulk_in)
{
return usb_find_common_endpoints_reverse(alt, bulk_in, NULL, NULL, NULL);
}
static inline int __must_check
usb_find_last_bulk_out_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **bulk_out)
{
return usb_find_common_endpoints_reverse(alt, NULL, bulk_out, NULL, NULL);
}
static inline int __must_check
usb_find_last_int_in_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **int_in)
{
return usb_find_common_endpoints_reverse(alt, NULL, NULL, int_in, NULL);
}
static inline int __must_check
usb_find_last_int_out_endpoint(struct usb_host_interface *alt,
struct usb_endpoint_descriptor **int_out)
{
return usb_find_common_endpoints_reverse(alt, NULL, NULL, NULL, int_out);
}
/**
* struct usb_interface - what usb device drivers talk to
* @altsetting: array of interface structures, one for each alternate
* setting that may be selected. Each one includes a set of
* endpoint configurations. They will be in no particular order.
* @cur_altsetting: the current altsetting.
* @num_altsetting: number of altsettings defined.
* @intf_assoc: interface association descriptor
* @minor: the minor number assigned to this interface, if this
* interface is bound to a driver that uses the USB major number.
* If this interface does not use the USB major, this field should
* be unused. The driver should set this value in the probe()
* function of the driver, after it has been assigned a minor
* number from the USB core by calling usb_register_dev().
* @condition: binding state of the interface: not bound, binding
* (in probe()), bound to a driver, or unbinding (in disconnect())
* @sysfs_files_created: sysfs attributes exist
* @ep_devs_created: endpoint child pseudo-devices exist
* @unregistering: flag set when the interface is being unregistered
* @needs_remote_wakeup: flag set when the driver requires remote-wakeup
* capability during autosuspend.
* @needs_altsetting0: flag set when a set-interface request for altsetting 0
* has been deferred.
* @needs_binding: flag set when the driver should be re-probed or unbound
* following a reset or suspend operation it doesn't support.
* @authorized: This allows to (de)authorize individual interfaces instead
* a whole device in contrast to the device authorization.
* @dev: driver model's view of this device
* @usb_dev: if an interface is bound to the USB major, this will point
* to the sysfs representation for that device.
* @pm_usage_cnt: PM usage counter for this interface
* @reset_ws: Used for scheduling resets from atomic context.
* @resetting_device: USB core reset the device, so use alt setting 0 as
* current; needs bandwidth alloc after reset.
*
* USB device drivers attach to interfaces on a physical device. Each
* interface encapsulates a single high level function, such as feeding
* an audio stream to a speaker or reporting a change in a volume control.
* Many USB devices only have one interface. The protocol used to talk to
* an interface's endpoints can be defined in a usb "class" specification,
* or by a product's vendor. The (default) control endpoint is part of
* every interface, but is never listed among the interface's descriptors.
*
* The driver that is bound to the interface can use standard driver model
* calls such as dev_get_drvdata() on the dev member of this structure.
*
* Each interface may have alternate settings. The initial configuration
* of a device sets altsetting 0, but the device driver can change
* that setting using usb_set_interface(). Alternate settings are often
* used to control the use of periodic endpoints, such as by having
* different endpoints use different amounts of reserved USB bandwidth.
* All standards-conformant USB devices that use isochronous endpoints
* will use them in non-default settings.
*
* The USB specification says that alternate setting numbers must run from
* 0 to one less than the total number of alternate settings. But some
* devices manage to mess this up, and the structures aren't necessarily
* stored in numerical order anyhow. Use usb_altnum_to_altsetting() to
* look up an alternate setting in the altsetting array based on its number.
*/
struct usb_interface {
/* array of alternate settings for this interface,
* stored in no particular order */
struct usb_host_interface *altsetting;
struct usb_host_interface *cur_altsetting; /* the currently
* active alternate setting */
unsigned num_altsetting; /* number of alternate settings */
/* If there is an interface association descriptor then it will list
* the associated interfaces */
struct usb_interface_assoc_descriptor *intf_assoc;
int minor; /* minor number this interface is
* bound to */
enum usb_interface_condition condition; /* state of binding */
unsigned sysfs_files_created:1; /* the sysfs attributes exist */
unsigned ep_devs_created:1; /* endpoint "devices" exist */
unsigned unregistering:1; /* unregistration is in progress */
unsigned needs_remote_wakeup:1; /* driver requires remote wakeup */
unsigned needs_altsetting0:1; /* switch to altsetting 0 is pending */
unsigned needs_binding:1; /* needs delayed unbind/rebind */
USB: Fix duplicate sysfs problem after device reset. Borislav Petkov reports issues with duplicate sysfs endpoint files after a resume from a hibernate. It turns out that the code to support alternate settings under xHCI has issues when a device with a non-default alternate setting is reset during the hibernate: [ 427.681810] Restarting tasks ... [ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000 [ 427.682019] usb usb3: usb resume [ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub [ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 427.682205] usb 1-2: usb wakeup-resume [ 427.682226] usb 1-2: finish reset-resume [ 427.682886] done. [ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed [ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT [ 427.746682] hub 3-0:1.0: hub_reset_resume [ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2 [ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed [ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT [ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS [ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1 [ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1 [ 427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed. [ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0 [ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1 [ 427.916609] ep_81: create, parent hub [ 427.916632] ------------[ cut here ]------------ [ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96() [ 427.916649] Hardware name: System Product Name [ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81' [ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat +8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core [ 427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869a-dirty #13 [ 427.916699] Call Trace: The problem is caused by a mismatch between the USB core's view of the device state and the USB device and xHCI host's view of the device state. After the device reset and re-configuration, the device and the xHCI host think they are using alternate setting 0 of all interfaces. However, the USB core keeps track of the old state, which may include non-zero alternate settings. It uses intf->cur_altsetting to keep the endpoint sysfs files for the old state across the reset. The bandwidth allocation functions need to know what the xHCI host thinks the current alternate settings are, so original patch set intf->cur_altsetting to the alternate setting 0. This caused duplicate endpoint files to be created. The solution is to not set intf->cur_altsetting before calling usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use alternate setting 0 as the currently installed alternate setting. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Borislav Petkov <petkovbb@googlemail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-01-06 18:16:51 +00:00
unsigned resetting_device:1; /* true: bandwidth alloc after reset */
unsigned authorized:1; /* used for interface authorization */
struct device dev; /* interface specific device info */
struct device *usb_dev;
atomic_t pm_usage_cnt; /* usage counter for autosuspend */
struct work_struct reset_ws; /* for resets in atomic context */
};
#define to_usb_interface(d) container_of(d, struct usb_interface, dev)
static inline void *usb_get_intfdata(struct usb_interface *intf)
{
return dev_get_drvdata(&intf->dev);
}
static inline void usb_set_intfdata(struct usb_interface *intf, void *data)
{
dev_set_drvdata(&intf->dev, data);
}
struct usb_interface *usb_get_intf(struct usb_interface *intf);
void usb_put_intf(struct usb_interface *intf);
/* Hard limit */
#define USB_MAXENDPOINTS 30
/* this maximum is arbitrary */
#define USB_MAXINTERFACES 32
#define USB_MAXIADS (USB_MAXINTERFACES/2)
/*
* USB Resume Timer: Every Host controller driver should drive the resume
* signalling on the bus for the amount of time defined by this macro.
*
* That way we will have a 'stable' behavior among all HCDs supported by Linux.
*
* Note that the USB Specification states we should drive resume for *at least*
* 20 ms, but it doesn't give an upper bound. This creates two possible
* situations which we want to avoid:
*
* (a) sometimes an msleep(20) might expire slightly before 20 ms, which causes
* us to fail USB Electrical Tests, thus failing Certification
*
* (b) Some (many) devices actually need more than 20 ms of resume signalling,
* and while we can argue that's against the USB Specification, we don't have
* control over which devices a certification laboratory will be using for
* certification. If CertLab uses a device which was tested against Windows and
* that happens to have relaxed resume signalling rules, we might fall into
* situations where we fail interoperability and electrical tests.
*
* In order to avoid both conditions, we're using a 40 ms resume timeout, which
* should cope with both LPJ calibration errors and devices not following every
* detail of the USB Specification.
*/
#define USB_RESUME_TIMEOUT 40 /* ms */
/**
* struct usb_interface_cache - long-term representation of a device interface
* @num_altsetting: number of altsettings defined.
* @ref: reference counter.
* @altsetting: variable-length array of interface structures, one for
* each alternate setting that may be selected. Each one includes a
* set of endpoint configurations. They will be in no particular order.
*
* These structures persist for the lifetime of a usb_device, unlike
* struct usb_interface (which persists only as long as its configuration
* is installed). The altsetting arrays can be accessed through these
* structures at any time, permitting comparison of configurations and
* providing support for the /sys/kernel/debug/usb/devices pseudo-file.
*/
struct usb_interface_cache {
unsigned num_altsetting; /* number of alternate settings */
struct kref ref; /* reference counter */
/* variable-length array of alternate settings for this interface,
* stored in no particular order */
struct usb_host_interface altsetting[0];
};
#define ref_to_usb_interface_cache(r) \
container_of(r, struct usb_interface_cache, ref)
#define altsetting_to_usb_interface_cache(a) \
container_of(a, struct usb_interface_cache, altsetting[0])
/**
* struct usb_host_config - representation of a device's configuration
* @desc: the device's configuration descriptor.
* @string: pointer to the cached version of the iConfiguration string, if
* present for this configuration.
* @intf_assoc: list of any interface association descriptors in this config
* @interface: array of pointers to usb_interface structures, one for each
* interface in the configuration. The number of interfaces is stored
* in desc.bNumInterfaces. These pointers are valid only while the
* the configuration is active.
* @intf_cache: array of pointers to usb_interface_cache structures, one
* for each interface in the configuration. These structures exist
* for the entire life of the device.
* @extra: pointer to buffer containing all extra descriptors associated
* with this configuration (those preceding the first interface
* descriptor).
* @extralen: length of the extra descriptors buffer.
*
* USB devices may have multiple configurations, but only one can be active
* at any time. Each encapsulates a different operational environment;
* for example, a dual-speed device would have separate configurations for
* full-speed and high-speed operation. The number of configurations
* available is stored in the device descriptor as bNumConfigurations.
*
* A configuration can contain multiple interfaces. Each corresponds to
* a different function of the USB device, and all are available whenever
* the configuration is active. The USB standard says that interfaces
* are supposed to be numbered from 0 to desc.bNumInterfaces-1, but a lot
* of devices get this wrong. In addition, the interface array is not
* guaranteed to be sorted in numerical order. Use usb_ifnum_to_if() to
* look up an interface entry based on its number.
*
* Device drivers should not attempt to activate configurations. The choice
* of which configuration to install is a policy decision based on such
* considerations as available power, functionality provided, and the user's
* desires (expressed through userspace tools). However, drivers can call
* usb_reset_configuration() to reinitialize the current configuration and
* all its interfaces.
*/
struct usb_host_config {
struct usb_config_descriptor desc;
char *string; /* iConfiguration string, if present */
/* List of any Interface Association Descriptors in this
* configuration. */
struct usb_interface_assoc_descriptor *intf_assoc[USB_MAXIADS];
/* the interfaces associated with this configuration,
* stored in no particular order */
struct usb_interface *interface[USB_MAXINTERFACES];
/* Interface information available even when this is not the
* active configuration */
struct usb_interface_cache *intf_cache[USB_MAXINTERFACES];
unsigned char *extra; /* Extra descriptors */
int extralen;
};
/* USB2.0 and USB3.0 device BOS descriptor set */
struct usb_host_bos {
struct usb_bos_descriptor *desc;
/* wireless cap descriptor is handled by wusb */
struct usb_ext_cap_descriptor *ext_cap;
struct usb_ss_cap_descriptor *ss_cap;
struct usb_ssp_cap_descriptor *ssp_cap;
struct usb_ss_container_id_descriptor *ss_id;
struct usb_ptm_cap_descriptor *ptm_cap;
};
int __usb_get_extra_descriptor(char *buffer, unsigned size,
unsigned char type, void **ptr);
#define usb_get_extra_descriptor(ifpoint, type, ptr) \
__usb_get_extra_descriptor((ifpoint)->extra, \
(ifpoint)->extralen, \
type, (void **)ptr)
/* ----------------------------------------------------------------------- */
/* USB device number allocation bitmap */
struct usb_devmap {
unsigned long devicemap[128 / (8*sizeof(unsigned long))];
};
/*
* Allocated per bus (tree of devices) we have:
*/
struct usb_bus {
struct device *controller; /* host/master side hardware */
usb: separate out sysdev pointer from usb_bus For xhci-hcd platform device, all the DMA parameters are not configured properly, notably dma ops for dwc3 devices. The idea here is that you pass in the parent of_node along with the child device pointer, so it would behave exactly like the parent already does. The difference is that it also handles all the other attributes besides the mask. sysdev will represent the physical device, as seen from firmware or bus.Splitting the usb_bus->controller field into the Linux-internal device (used for the sysfs hierarchy, for printks and for power management) and a new pointer (used for DMA, DT enumeration and phy lookup) probably covers all that we really need. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Tested-by: Baolin Wang <baolin.wang@linaro.org> Tested-by: Brian Norris <briannorris@chromium.org> Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Sinjan Kumar <sinjank@codeaurora.org> Cc: David Fisher <david.fisher1@synopsys.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: "Thang Q. Nguyen" <tqnguyen@apm.com> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Ming Lei <tom.leiming@gmail.com> Cc: Jon Masters <jcm@redhat.com> Cc: Dann Frazier <dann.frazier@canonical.com> Cc: Peter Chen <peter.chen@nxp.com> Cc: Leo Li <pku.leo@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-13 02:18:41 +00:00
struct device *sysdev; /* as seen from firmware or bus */
int busnum; /* Bus number (in order of reg) */
const char *bus_name; /* stable id (PCI slot_name etc) */
u8 uses_dma; /* Does the host controller use DMA? */
u8 uses_pio_for_control; /*
* Does the host controller use PIO
* for control transfers?
*/
u8 otg_port; /* 0, or number of OTG/HNP port */
unsigned is_b_host:1; /* true during some HNP roleswitches */
unsigned b_hnp_enable:1; /* OTG: did A-Host enable HNP? */
usbdevfs: Add a USBDEVFS_GET_CAPABILITIES ioctl There are a few (new) usbdevfs capabilities which an application cannot discover in any other way then checking the kernel version. There are 3 problems with this: 1) It is just not very pretty. 2) Given the tendency of enterprise distros to backport stuff it is not reliable. 3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK (which is its intended use) on devices attached to an XHCI controller. So the availability of these features can be host controller dependent, making depending on them based on the kernel version not a good idea. This patch besides adding the new ioctl also adds flags for the following existing capabilities: USBDEVFS_CAP_ZERO_PACKET, available since 2.6.31 USBDEVFS_CAP_BULK_CONTINUATION, available since 2.6.32, except for XHCI USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3 Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION cap for XHCI controllers, bulk transfers with this flag set will still be accepted when submitted to XHCI controllers. Returning -EINVAL for them would break existing apps, and in most cases the troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers will never get hit, so this would break working use cases. The disadvantage of not returning -EINVAL is that cases were it is causing real trouble may go undetected / the cause of the trouble may be unclear, but this is the best we can do. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-07-04 07:18:02 +00:00
unsigned no_stop_on_short:1; /*
* Quirk: some controllers don't stop
* the ep queue on a short transfer
* with the URB_SHORT_NOT_OK flag set.
*/
unsigned no_sg_constraint:1; /* no sg constraint */
unsigned sg_tablesize; /* 0 or largest number of sg list entries */
int devnum_next; /* Next open device number in
* round-robin allocation */
usb: core: hub: hub_port_init lock controller instead of bus The XHCI controller presents two USB buses to the system - one for USB2 and one for USB3. The hub init code (hub_port_init) is reentrant but only locks one bus per thread, leading to a race condition failure when two threads attempt to simultaneously initialise a USB2 and USB3 device: [ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command [ 13.183701] usb 3-3: device descriptor read/all, error -110 On a test system this failure occurred on 6% of all boots. The call traces at the point of failure are: Call Trace: [<ffffffff81b9bab7>] schedule+0x37/0x90 [<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0 [<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30 [<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150 [<ffffffff817db10c>] usb_control_msg+0xbc/0xf0 [<ffffffff817d07de>] hub_port_init+0x51e/0xb70 [<ffffffff817d4697>] hub_event+0x817/0x1570 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620 [<ffffffff810f4684>] worker_thread+0x64/0x4b0 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390 [<ffffffff810fa7f5>] kthread+0x105/0x120 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 Call Trace: [<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40 [<ffffffff817fd87e>] xhci_address_device+0xe/0x10 [<ffffffff817d047f>] hub_port_init+0x1bf/0xb70 [<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff817d4697>] hub_event+0x817/0x1570 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620 [<ffffffff810f4684>] worker_thread+0x64/0x4b0 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390 [<ffffffff810fa7f5>] kthread+0x105/0x120 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 Which results from the two call chains: hub_port_init usb_get_device_descriptor usb_get_descriptor usb_control_msg usb_internal_control_msg usb_start_wait_urb usb_submit_urb / wait_for_completion_timeout / usb_kill_urb hub_port_init hub_set_address xhci_address_device xhci_setup_device Mathias Nyman explains the current behaviour violates the XHCI spec: hub_port_reset() will end up moving the corresponding xhci device slot to default state. As hub_port_reset() is called several times in hub_port_init() it sounds reasonable that we could end up with two threads having their xhci device slots in default state at the same time, which according to xhci 4.5.3 specs still is a big no no: "Note: Software shall not transition more than one Device Slot to the Default State at a time" So both threads fail at their next task after this. One fails to read the descriptor, and the other fails addressing the device. Fix this in hub_port_init by locking the USB controller (instead of an individual bus) to prevent simultaneous initialisation of both buses. Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel") Link: https://lkml.org/lkml/2016/2/8/312 Link: https://lkml.org/lkml/2016/2/4/748 Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-25 12:48:38 +00:00
struct mutex devnum_next_mutex; /* devnum_next mutex */
struct usb_devmap devmap; /* device address allocation map */
struct usb_device *root_hub; /* Root hub */
2010-02-12 11:21:11 +00:00
struct usb_bus *hs_companion; /* Companion EHCI bus, if any */
int bandwidth_allocated; /* on this bus: how much of the time
* reserved for periodic (intr/iso)
* requests is used, on average?
* Units: microseconds/frame.
* Limits: Full/low speed reserve 90%,
* while high speed reserves 80%.
*/
int bandwidth_int_reqs; /* number of Interrupt requests */
int bandwidth_isoc_reqs; /* number of Isoc. requests */
unsigned resuming_ports; /* bit array: resuming root-hub ports */
#if defined(CONFIG_USB_MON) || defined(CONFIG_USB_MON_MODULE)
struct mon_bus *mon_bus; /* non-null when associated */
int monitored; /* non-zero when monitored */
#endif
};
struct usb_dev_state;
/* ----------------------------------------------------------------------- */
struct usb_tt;
enum usb_device_removable {
USB_DEVICE_REMOVABLE_UNKNOWN = 0,
USB_DEVICE_REMOVABLE,
USB_DEVICE_FIXED,
};
2012-09-05 05:44:34 +00:00
enum usb_port_connect_type {
USB_PORT_CONNECT_TYPE_UNKNOWN = 0,
USB_PORT_CONNECT_TYPE_HOT_PLUG,
USB_PORT_CONNECT_TYPE_HARD_WIRED,
USB_PORT_NOT_USED,
};
/*
* USB port quirks.
*/
/* For the given port, prefer the old (faster) enumeration scheme. */
#define USB_PORT_QUIRK_OLD_SCHEME BIT(0)
/* Decrease TRSTRCY to 10ms during device enumeration. */
#define USB_PORT_QUIRK_FAST_ENUM BIT(1)
/*
* USB 2.0 Link Power Management (LPM) parameters.
*/
struct usb2_lpm_parameters {
/* Best effort service latency indicate how long the host will drive
* resume on an exit from L1.
*/
unsigned int besl;
/* Timeout value in microseconds for the L1 inactivity (LPM) timer.
* When the timer counts to zero, the parent hub will initiate a LPM
* transition to L1.
*/
int timeout;
};
USB: Calculate USB 3.0 exit latencies for LPM. There are several different exit latencies associated with coming out of the U1 or U2 lower power link state. Device Exit Latency (DEL) is the maximum time it takes for the USB device to bring its upstream link into U0. That can be found in the SuperSpeed Extended Capabilities BOS descriptor for the device. The time it takes for a particular link in the tree to exit to U0 is the maximum of either the parent hub's U1/U2 DEL, or the child's U1/U2 DEL. Hubs introduce a further delay that effects how long it takes a child device to transition to U0. When a USB 3.0 hub receives a header packet, it takes some time to decode that header and figure out which downstream port the packet was destined for. If the port is not in U0, this hub header decode latency will cause an additional delay for bringing the child device to U0. This Hub Header Decode Latency is found in the USB 3.0 hub descriptor. We can use DEL and the header decode latency, along with additional latencies imposed by each additional hub tier, to figure out the exit latencies for both host-initiated and device-initiated exit to U0. The Max Exit Latency (MEL) is the worst-case time it will take for a host-initiated exit to U0, based on whether U1 or U2 link states are enabled. The ping or packet must traverse the path to the device, and each hub along the way incurs the hub header decode latency in order to figure out which device the transfer was bound for. We say worst-case, because some hubs may not be in the lowest link state that is enabled. See the examples in section C.2.2.1. Note that "HSD" is a "host specific delay" that the power appendix architect has not been able to tell me how to calculate. There's no way to get HSD from the xHCI registers either, so I'm simply ignoring it. The Path Exit Latency (PEL) is the worst-case time it will take for a device-initiate exit to U0 to place all the links from the device to the host into U0. The System Exit Latency (SEL) is another device-initiated exit latency. SEL is useful for USB 3.0 devices that need to send data to the host at specific intervals. The device may send an NRDY to indicate it isn't ready to send data, then put its link into a lower power state. If it needs to have that data transmitted at a specific time, it can use SEL to back calculate when it will need to bring the link back into U0 to meet its deadlines. SEL is the worst-case time from the device-initiated exit to U0, to when the device will receive a packet from the host controller. It includes PEL, the time it takes for an ERDY to get to the host, a host-specific delay for the host to process that ERDY, and the time it takes for the packet to traverse the path to the device. See Figure C-2 in the USB 3.0 bus specification. Note: I have not been able to get good answers about what the host-specific delay to process the ERDY should be. The Intel HW developers say it will be specific to the platform the xHCI host is integrated into, and they say it's negligible. Ignore this too. Separate from these four exit latencies are the U1/U2 timeout values we program into the parent hubs. These timeouts tell the hub to attempt to place the device into a lower power link state after the link has been idle for that amount of time. Create two arrays (one for U1 and one for U2) to store mel, pel, sel, and the timeout values. Store the exit latency values in nanosecond units, since that's the smallest units used (DEL is in us, but the Hub Header Decode Latency is in ns). If a USB 3.0 device doesn't have a SuperSpeed Extended Capabilities BOS descriptor, it's highly unlikely it will be able to handle LPM requests properly. So it's best to disable LPM for devices that don't have this descriptor, and any children beneath it, if it's a USB 3.0 hub. Warn users when that happens, since it means they have a non-compliant USB 3.0 device or hub. This patch assumes a simplified design where links deep in the tree will not have U1 or U2 enabled unless all their parent links have the corresponding LPM state enabled. Eventually, we might want to allow a different policy, and we can revisit this patch when that happens. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu>
2012-02-20 20:02:19 +00:00
/*
* USB 3.0 Link Power Management (LPM) parameters.
*
* PEL and SEL are USB 3.0 Link PM latencies for device-initiated LPM exit.
* MEL is the USB 3.0 Link PM latency for host-initiated LPM exit.
* All three are stored in nanoseconds.
*/
struct usb3_lpm_parameters {
/*
* Maximum exit latency (MEL) for the host to send a packet to the
* device (either a Ping for isoc endpoints, or a data packet for
* interrupt endpoints), the hubs to decode the packet, and for all hubs
* in the path to transition the links to U0.
*/
unsigned int mel;
/*
* Maximum exit latency for a device-initiated LPM transition to bring
* all links into U0. Abbreviated as "PEL" in section 9.4.12 of the USB
* 3.0 spec, with no explanation of what "P" stands for. "Path"?
*/
unsigned int pel;
/*
* The System Exit Latency (SEL) includes PEL, and three other
* latencies. After a device initiates a U0 transition, it will take
* some time from when the device sends the ERDY to when it will finally
* receive the data packet. Basically, SEL should be the worse-case
* latency from when a device starts initiating a U0 transition to when
* it will get data.
*/
unsigned int sel;
USB: Add support to enable/disable USB3 link states. There are various functions within the USB core that will need to disable USB 3.0 link power states. For example, when a USB device driver is being bound to an interface, we need to disable USB 3.0 LPM until we know if the driver will allow hub-initiated LPM transitions. Another example is when the USB core is switching alternate interface settings. The USB 3.0 timeout values are dependent on what endpoints are enabled, so we want to ensure that LPM is disabled until the new alt setting is fully installed. Multiple functions need to disable LPM, and those functions can even be nested. For example, usb_bind_interface() could disable LPM, and then call into the driver probe function, which may attempt to switch to a different alt setting. Therefore, we need to keep a count of the number of functions that require LPM to be disabled at any point in time. Introduce two new USB core API calls, usb_disable_lpm() and usb_enable_lpm(). These functions increment and decrement a new variable in the usb_device, lpm_disable_count. If usb_disable_lpm() fails, it will call usb_enable_lpm() in order to balance the lpm_disable_count. These two new functions must be called with the bandwidth_mutex locked. If the bandwidth_mutex is not already held by the caller, it should instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take the bandwidth_mutex before calling usb_disable_lpm() and usb_enable_lpm(), respectively. Introduce a new variable (timeout) in the usb3_lpm_params structure to keep track of the currently enabled U1/U2 timeout values. When usb_disable_lpm() is called, and the USB device has the U1 or U2 timeouts set to a non-zero value (meaning either device-initiated or hub-initiated LPM is enabled), attempt to disable LPM, regardless of the state of the lpm_disable_count. We want to ensure that all callers can be guaranteed that LPM is disabled if usb_disable_lpm() returns zero. Otherwise the following scenario could occur: 1. Driver A is being bound to interface 1. usb_probe_interface() disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so even though usb_disable_lpm() fails, the probe of the driver continues, and the bandwidth mutex is dropped. 2. Meanwhile, Driver B is being bound to interface 2. usb_probe_interface() grabs the bandwidth mutex and calls usb_disable_lpm(). That call should attempt to disable LPM, even though the lpm_disable_count is set to 1 by Driver A. For usb_enable_lpm(), we attempt to enable LPM only when the lpm_disable_count is zero. If some step in enabling LPM fails, it will only have a minimal impact on power consumption, and all USB device drivers should still work properly. Therefore don't bother to return any error codes. Don't enable device-initiated LPM if the device is unconfigured. The USB device will only accept the U1/U2_ENABLE control transfers in the configured state. Do enable hub-initiated LPM in that case, since devices are allowed to accept the LGO_Ux link commands in any state. Don't enable or disable LPM if the device is marked as not being LPM capable. This can happen if: - the USB device doesn't have a SS BOS descriptor, - the device's parent hub has a zeroed bHeaderDecodeLatency value, or - the xHCI host doesn't support LPM. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Andiry Xu <andiry.xu@amd.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-04-25 00:21:50 +00:00
/*
* The idle timeout value that is currently programmed into the parent
* hub for this device. When the timer counts to zero, the parent hub
* will initiate an LPM transition to either U1 or U2.
*/
int timeout;
USB: Calculate USB 3.0 exit latencies for LPM. There are several different exit latencies associated with coming out of the U1 or U2 lower power link state. Device Exit Latency (DEL) is the maximum time it takes for the USB device to bring its upstream link into U0. That can be found in the SuperSpeed Extended Capabilities BOS descriptor for the device. The time it takes for a particular link in the tree to exit to U0 is the maximum of either the parent hub's U1/U2 DEL, or the child's U1/U2 DEL. Hubs introduce a further delay that effects how long it takes a child device to transition to U0. When a USB 3.0 hub receives a header packet, it takes some time to decode that header and figure out which downstream port the packet was destined for. If the port is not in U0, this hub header decode latency will cause an additional delay for bringing the child device to U0. This Hub Header Decode Latency is found in the USB 3.0 hub descriptor. We can use DEL and the header decode latency, along with additional latencies imposed by each additional hub tier, to figure out the exit latencies for both host-initiated and device-initiated exit to U0. The Max Exit Latency (MEL) is the worst-case time it will take for a host-initiated exit to U0, based on whether U1 or U2 link states are enabled. The ping or packet must traverse the path to the device, and each hub along the way incurs the hub header decode latency in order to figure out which device the transfer was bound for. We say worst-case, because some hubs may not be in the lowest link state that is enabled. See the examples in section C.2.2.1. Note that "HSD" is a "host specific delay" that the power appendix architect has not been able to tell me how to calculate. There's no way to get HSD from the xHCI registers either, so I'm simply ignoring it. The Path Exit Latency (PEL) is the worst-case time it will take for a device-initiate exit to U0 to place all the links from the device to the host into U0. The System Exit Latency (SEL) is another device-initiated exit latency. SEL is useful for USB 3.0 devices that need to send data to the host at specific intervals. The device may send an NRDY to indicate it isn't ready to send data, then put its link into a lower power state. If it needs to have that data transmitted at a specific time, it can use SEL to back calculate when it will need to bring the link back into U0 to meet its deadlines. SEL is the worst-case time from the device-initiated exit to U0, to when the device will receive a packet from the host controller. It includes PEL, the time it takes for an ERDY to get to the host, a host-specific delay for the host to process that ERDY, and the time it takes for the packet to traverse the path to the device. See Figure C-2 in the USB 3.0 bus specification. Note: I have not been able to get good answers about what the host-specific delay to process the ERDY should be. The Intel HW developers say it will be specific to the platform the xHCI host is integrated into, and they say it's negligible. Ignore this too. Separate from these four exit latencies are the U1/U2 timeout values we program into the parent hubs. These timeouts tell the hub to attempt to place the device into a lower power link state after the link has been idle for that amount of time. Create two arrays (one for U1 and one for U2) to store mel, pel, sel, and the timeout values. Store the exit latency values in nanosecond units, since that's the smallest units used (DEL is in us, but the Hub Header Decode Latency is in ns). If a USB 3.0 device doesn't have a SuperSpeed Extended Capabilities BOS descriptor, it's highly unlikely it will be able to handle LPM requests properly. So it's best to disable LPM for devices that don't have this descriptor, and any children beneath it, if it's a USB 3.0 hub. Warn users when that happens, since it means they have a non-compliant USB 3.0 device or hub. This patch assumes a simplified design where links deep in the tree will not have U1 or U2 enabled unless all their parent links have the corresponding LPM state enabled. Eventually, we might want to allow a different policy, and we can revisit this patch when that happens. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu>
2012-02-20 20:02:19 +00:00
};
/**
* struct usb_device - kernel's representation of a USB device
* @devnum: device number; address on a USB bus
* @devpath: device ID string for use in messages (e.g., /port/...)
* @route: tree topology hex string for use with xHCI
* @state: device state: configured, not attached, etc.
* @speed: device speed: high/full/low (or error)
* @rx_lanes: number of rx lanes in use, USB 3.2 adds dual-lane support
* @tx_lanes: number of tx lanes in use, USB 3.2 adds dual-lane support
* @tt: Transaction Translator info; used with low/full speed dev, highspeed hub
* @ttport: device port on that tt hub
* @toggle: one bit for each endpoint, with ([0] = IN, [1] = OUT) endpoints
* @parent: our hub, unless we're the root
* @bus: bus we're part of
* @ep0: endpoint 0 data (default control pipe)
* @dev: generic device interface
* @descriptor: USB device descriptor
* @bos: USB device BOS descriptor set
* @config: all of the device's configs
* @actconfig: the active configuration
* @ep_in: array of IN endpoints
* @ep_out: array of OUT endpoints
* @rawdescriptors: raw descriptors for each config
* @bus_mA: Current available from the bus
* @portnum: parent port number (origin 1)
* @level: number of USB hub ancestors
* @can_submit: URBs may be submitted
* @persist_enabled: USB_PERSIST enabled for this device
* @have_langid: whether string_langid is valid
* @authorized: policy has said we can use it;
* (user space) policy determines if we authorize this device to be
* used or not. By default, wired USB devices are authorized.
* WUSB devices are not, until we authorize them from user space.
* FIXME -- complete doc
* @authenticated: Crypto authentication passed
* @wusb: device is Wireless USB
* @lpm_capable: device supports LPM
* @usb2_hw_lpm_capable: device can perform USB2 hardware LPM
* @usb2_hw_lpm_besl_capable: device can perform USB2 hardware BESL LPM
usb: Don't enable USB 2.0 Link PM by default. How it's supposed to work: -------------------------- USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices support. USB 3.0 devices certified by the USB-IF are required to support it if they are plugged into a USB 2.0 only port, or a USB 2.0 cable is used. USB 2.0 Link PM requires both a USB device and a host controller that supports USB 2.0 hardware-enabled LPM. USB 2.0 Link PM is designed to be enabled once by software, and the host hardware handles transitions to the L1 state automatically. The premise of USB 2.0 Link PM is to be able to put the device into a lower power link state when the bus is idle or the device NAKs USB IN transfers for a specified amount of time. ...but hardware is broken: -------------------------- It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by setting the LPM bit in their USB 2.0 BOS descriptor), but they don't actually implement it correctly. This manifests as the USB device refusing to respond to transfers when it is plugged into a USB 2.0 only port under the Haswell-ULT/Lynx Point LP xHCI host. These devices pass the xHCI driver's simple test to enable USB 2.0 Link PM, wait for the port to enter L1, and then bring it back into L0. They only start to break when L1 entry is interleaved with transfers. Some devices then fail to respond to the next control transfer (usually a Set Configuration). This results in devices never enumerating. Other mass storage devices (such as a later model Western Digital My Passport USB 3.0 hard drive) respond fine to going into L1 between control transfers. They ACK the entry, come out of L1 when the host needs to send a control transfer, and respond properly to those control transfers. However, when the first READ10 SCSI command is sent, the device NAKs the data phase while it's reading from the spinning disk. Eventually, the host requests to put the link into L1, and the device ACKs that request. Then it never responds to the data phase of the READ10 command. This results in not being able to read from the drive. Some mass storage devices (like the Corsair Survivor USB 3.0 flash drive) are well behaved. They ACK the entry into L1 during control transfers, and when SCSI commands start coming in, they NAK the requests to go into L1, because they need to be at full power. Not all USB 3.0 devices advertise USB 2.0 link PM support. My Point Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM. I suspect that means the device isn't certified. What do we do about it? ----------------------- There's really no good way for the kernel to test these devices. Therefore, the kernel needs to disable USB 2.0 Link PM by default, and distros will have to enable it by writing 1 to the sysfs file /sys/bus/usb/devices/../power/usb2_hardware_lpm. Rip out the xHCI Link PM test, since it's not sufficient to detect these buggy devices, and don't automatically enable LPM after the device is addressed. This patch should be backported to kernels as old as 3.11, that contain the commit a558ccdcc71c7770c5e80c926a31cfe8a3892a09 "usb: xhci: add USB2 Link power management BESL support". Without this fix, some USB 3.0 devices will not enumerate or work properly under USB 2.0 ports on Haswell-ULT systems. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org
2013-09-30 14:26:28 +00:00
* @usb2_hw_lpm_enabled: USB2 hardware LPM is enabled
* @usb2_hw_lpm_allowed: Userspace allows USB 2.0 LPM to be enabled
* @usb3_lpm_u1_enabled: USB3 hardware U1 LPM enabled
* @usb3_lpm_u2_enabled: USB3 hardware U2 LPM enabled
* @string_langid: language ID for strings
* @product: iProduct string, if present (static)
* @manufacturer: iManufacturer string, if present (static)
* @serial: iSerialNumber string, if present (static)
* @filelist: usbfs files that are open to this device
* @maxchild: number of ports if hub
* @quirks: quirks of the whole device
* @urbnum: number of URBs submitted for the whole device
* @active_duration: total time device is not suspended
* @connect_time: time device was first connected
* @do_remote_wakeup: remote wakeup should be enabled
* @reset_resume: needs reset instead of resume
* @port_is_suspended: the upstream port is suspended (L2 or U3)
* @wusb_dev: if this is a Wireless USB device, link to the WUSB
* specific data for the device.
* @slot_id: Slot ID assigned by xHCI
* @removable: Device can be physically removed from this port
* @l1_params: best effor service latency for USB2 L1 LPM state, and L1 timeout.
USB: Add support to enable/disable USB3 link states. There are various functions within the USB core that will need to disable USB 3.0 link power states. For example, when a USB device driver is being bound to an interface, we need to disable USB 3.0 LPM until we know if the driver will allow hub-initiated LPM transitions. Another example is when the USB core is switching alternate interface settings. The USB 3.0 timeout values are dependent on what endpoints are enabled, so we want to ensure that LPM is disabled until the new alt setting is fully installed. Multiple functions need to disable LPM, and those functions can even be nested. For example, usb_bind_interface() could disable LPM, and then call into the driver probe function, which may attempt to switch to a different alt setting. Therefore, we need to keep a count of the number of functions that require LPM to be disabled at any point in time. Introduce two new USB core API calls, usb_disable_lpm() and usb_enable_lpm(). These functions increment and decrement a new variable in the usb_device, lpm_disable_count. If usb_disable_lpm() fails, it will call usb_enable_lpm() in order to balance the lpm_disable_count. These two new functions must be called with the bandwidth_mutex locked. If the bandwidth_mutex is not already held by the caller, it should instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take the bandwidth_mutex before calling usb_disable_lpm() and usb_enable_lpm(), respectively. Introduce a new variable (timeout) in the usb3_lpm_params structure to keep track of the currently enabled U1/U2 timeout values. When usb_disable_lpm() is called, and the USB device has the U1 or U2 timeouts set to a non-zero value (meaning either device-initiated or hub-initiated LPM is enabled), attempt to disable LPM, regardless of the state of the lpm_disable_count. We want to ensure that all callers can be guaranteed that LPM is disabled if usb_disable_lpm() returns zero. Otherwise the following scenario could occur: 1. Driver A is being bound to interface 1. usb_probe_interface() disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so even though usb_disable_lpm() fails, the probe of the driver continues, and the bandwidth mutex is dropped. 2. Meanwhile, Driver B is being bound to interface 2. usb_probe_interface() grabs the bandwidth mutex and calls usb_disable_lpm(). That call should attempt to disable LPM, even though the lpm_disable_count is set to 1 by Driver A. For usb_enable_lpm(), we attempt to enable LPM only when the lpm_disable_count is zero. If some step in enabling LPM fails, it will only have a minimal impact on power consumption, and all USB device drivers should still work properly. Therefore don't bother to return any error codes. Don't enable device-initiated LPM if the device is unconfigured. The USB device will only accept the U1/U2_ENABLE control transfers in the configured state. Do enable hub-initiated LPM in that case, since devices are allowed to accept the LGO_Ux link commands in any state. Don't enable or disable LPM if the device is marked as not being LPM capable. This can happen if: - the USB device doesn't have a SS BOS descriptor, - the device's parent hub has a zeroed bHeaderDecodeLatency value, or - the xHCI host doesn't support LPM. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Andiry Xu <andiry.xu@amd.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-04-25 00:21:50 +00:00
* @u1_params: exit latencies for USB3 U1 LPM state, and hub-initiated timeout.
* @u2_params: exit latencies for USB3 U2 LPM state, and hub-initiated timeout.
* @lpm_disable_count: Ref count used by usb_disable_lpm() and usb_enable_lpm()
* to keep track of the number of functions that require USB 3.0 Link Power
* Management to be disabled for this usb_device. This count should only
* be manipulated by those functions, with the bandwidth_mutex is held.
* @hub_delay: cached value consisting of:
* parent->hub_delay + wHubDelay + tTPTransmissionDelay (40ns)
*
* Will be used as wValue for SetIsochDelay requests.
*
* Notes:
* Usbcore drivers should not set usbdev->state directly. Instead use
* usb_set_device_state().
*/
struct usb_device {
int devnum;
char devpath[16];
u32 route;
enum usb_device_state state;
enum usb_device_speed speed;
unsigned int rx_lanes;
unsigned int tx_lanes;
struct usb_tt *tt;
int ttport;
unsigned int toggle[2];
struct usb_device *parent;
struct usb_bus *bus;
struct usb_host_endpoint ep0;
struct device dev;
struct usb_device_descriptor descriptor;
struct usb_host_bos *bos;
struct usb_host_config *config;
struct usb_host_config *actconfig;
struct usb_host_endpoint *ep_in[16];
struct usb_host_endpoint *ep_out[16];
char **rawdescriptors;
unsigned short bus_mA;
u8 portnum;
u8 level;
[PATCH] USB: Consider power budget when choosing configuration This patch (as609) changes the way we keep track of power budgeting for USB hubs and devices, and it updates the choose_configuration routine to take this information into account. (This is something we should have been doing all along.) A new field in struct usb_device holds the amount of bus current available from the upstream port, and the usb_hub structure keeps track of the current available for each downstream port. Two new rules for configuration selection are added: Don't select a self-powered configuration when only bus power is available. Don't select a configuration requiring more bus power than is available. However the first rule is #if-ed out, because I found that the internal hub in my HP USB keyboard claims that its only configuration is self-powered. The rule would prevent the configuration from being chosen, leaving the hub & keyboard unconfigured. Since similar descriptor errors may turn out to be fairly common, it seemed wise not to include a rule that would break automatic configuration unnecessarily for such devices. The second rule may also trigger unnecessarily, although this should be less common. More likely it will annoy people by sometimes failing to accept configurations that should never have been chosen in the first place. The patch also changes usbcore's reaction when no configuration is suitable. Instead of raising an error and rejecting the device, now the core will simply leave the device unconfigured. People can always work around such problems by installing configurations manually through sysfs. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-23 17:03:12 +00:00
unsigned can_submit:1;
unsigned persist_enabled:1;
unsigned have_langid:1;
unsigned authorized:1;
unsigned authenticated:1;
unsigned wusb:1;
unsigned lpm_capable:1;
unsigned usb2_hw_lpm_capable:1;
unsigned usb2_hw_lpm_besl_capable:1;
unsigned usb2_hw_lpm_enabled:1;
usb: Don't enable USB 2.0 Link PM by default. How it's supposed to work: -------------------------- USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices support. USB 3.0 devices certified by the USB-IF are required to support it if they are plugged into a USB 2.0 only port, or a USB 2.0 cable is used. USB 2.0 Link PM requires both a USB device and a host controller that supports USB 2.0 hardware-enabled LPM. USB 2.0 Link PM is designed to be enabled once by software, and the host hardware handles transitions to the L1 state automatically. The premise of USB 2.0 Link PM is to be able to put the device into a lower power link state when the bus is idle or the device NAKs USB IN transfers for a specified amount of time. ...but hardware is broken: -------------------------- It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by setting the LPM bit in their USB 2.0 BOS descriptor), but they don't actually implement it correctly. This manifests as the USB device refusing to respond to transfers when it is plugged into a USB 2.0 only port under the Haswell-ULT/Lynx Point LP xHCI host. These devices pass the xHCI driver's simple test to enable USB 2.0 Link PM, wait for the port to enter L1, and then bring it back into L0. They only start to break when L1 entry is interleaved with transfers. Some devices then fail to respond to the next control transfer (usually a Set Configuration). This results in devices never enumerating. Other mass storage devices (such as a later model Western Digital My Passport USB 3.0 hard drive) respond fine to going into L1 between control transfers. They ACK the entry, come out of L1 when the host needs to send a control transfer, and respond properly to those control transfers. However, when the first READ10 SCSI command is sent, the device NAKs the data phase while it's reading from the spinning disk. Eventually, the host requests to put the link into L1, and the device ACKs that request. Then it never responds to the data phase of the READ10 command. This results in not being able to read from the drive. Some mass storage devices (like the Corsair Survivor USB 3.0 flash drive) are well behaved. They ACK the entry into L1 during control transfers, and when SCSI commands start coming in, they NAK the requests to go into L1, because they need to be at full power. Not all USB 3.0 devices advertise USB 2.0 link PM support. My Point Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM. I suspect that means the device isn't certified. What do we do about it? ----------------------- There's really no good way for the kernel to test these devices. Therefore, the kernel needs to disable USB 2.0 Link PM by default, and distros will have to enable it by writing 1 to the sysfs file /sys/bus/usb/devices/../power/usb2_hardware_lpm. Rip out the xHCI Link PM test, since it's not sufficient to detect these buggy devices, and don't automatically enable LPM after the device is addressed. This patch should be backported to kernels as old as 3.11, that contain the commit a558ccdcc71c7770c5e80c926a31cfe8a3892a09 "usb: xhci: add USB2 Link power management BESL support". Without this fix, some USB 3.0 devices will not enumerate or work properly under USB 2.0 ports on Haswell-ULT systems. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org
2013-09-30 14:26:28 +00:00
unsigned usb2_hw_lpm_allowed:1;
unsigned usb3_lpm_u1_enabled:1;
unsigned usb3_lpm_u2_enabled:1;
int string_langid;
/* static strings from the device */
char *product;
char *manufacturer;
char *serial;
struct list_head filelist;
int maxchild;
u32 quirks;
atomic_t urbnum;
unsigned long active_duration;
#ifdef CONFIG_PM
unsigned long connect_time;
unsigned do_remote_wakeup:1;
unsigned reset_resume:1;
unsigned port_is_suspended:1;
#endif
struct wusb_dev *wusb_dev;
int slot_id;
enum usb_device_removable removable;
struct usb2_lpm_parameters l1_params;
USB: Calculate USB 3.0 exit latencies for LPM. There are several different exit latencies associated with coming out of the U1 or U2 lower power link state. Device Exit Latency (DEL) is the maximum time it takes for the USB device to bring its upstream link into U0. That can be found in the SuperSpeed Extended Capabilities BOS descriptor for the device. The time it takes for a particular link in the tree to exit to U0 is the maximum of either the parent hub's U1/U2 DEL, or the child's U1/U2 DEL. Hubs introduce a further delay that effects how long it takes a child device to transition to U0. When a USB 3.0 hub receives a header packet, it takes some time to decode that header and figure out which downstream port the packet was destined for. If the port is not in U0, this hub header decode latency will cause an additional delay for bringing the child device to U0. This Hub Header Decode Latency is found in the USB 3.0 hub descriptor. We can use DEL and the header decode latency, along with additional latencies imposed by each additional hub tier, to figure out the exit latencies for both host-initiated and device-initiated exit to U0. The Max Exit Latency (MEL) is the worst-case time it will take for a host-initiated exit to U0, based on whether U1 or U2 link states are enabled. The ping or packet must traverse the path to the device, and each hub along the way incurs the hub header decode latency in order to figure out which device the transfer was bound for. We say worst-case, because some hubs may not be in the lowest link state that is enabled. See the examples in section C.2.2.1. Note that "HSD" is a "host specific delay" that the power appendix architect has not been able to tell me how to calculate. There's no way to get HSD from the xHCI registers either, so I'm simply ignoring it. The Path Exit Latency (PEL) is the worst-case time it will take for a device-initiate exit to U0 to place all the links from the device to the host into U0. The System Exit Latency (SEL) is another device-initiated exit latency. SEL is useful for USB 3.0 devices that need to send data to the host at specific intervals. The device may send an NRDY to indicate it isn't ready to send data, then put its link into a lower power state. If it needs to have that data transmitted at a specific time, it can use SEL to back calculate when it will need to bring the link back into U0 to meet its deadlines. SEL is the worst-case time from the device-initiated exit to U0, to when the device will receive a packet from the host controller. It includes PEL, the time it takes for an ERDY to get to the host, a host-specific delay for the host to process that ERDY, and the time it takes for the packet to traverse the path to the device. See Figure C-2 in the USB 3.0 bus specification. Note: I have not been able to get good answers about what the host-specific delay to process the ERDY should be. The Intel HW developers say it will be specific to the platform the xHCI host is integrated into, and they say it's negligible. Ignore this too. Separate from these four exit latencies are the U1/U2 timeout values we program into the parent hubs. These timeouts tell the hub to attempt to place the device into a lower power link state after the link has been idle for that amount of time. Create two arrays (one for U1 and one for U2) to store mel, pel, sel, and the timeout values. Store the exit latency values in nanosecond units, since that's the smallest units used (DEL is in us, but the Hub Header Decode Latency is in ns). If a USB 3.0 device doesn't have a SuperSpeed Extended Capabilities BOS descriptor, it's highly unlikely it will be able to handle LPM requests properly. So it's best to disable LPM for devices that don't have this descriptor, and any children beneath it, if it's a USB 3.0 hub. Warn users when that happens, since it means they have a non-compliant USB 3.0 device or hub. This patch assumes a simplified design where links deep in the tree will not have U1 or U2 enabled unless all their parent links have the corresponding LPM state enabled. Eventually, we might want to allow a different policy, and we can revisit this patch when that happens. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu>
2012-02-20 20:02:19 +00:00
struct usb3_lpm_parameters u1_params;
struct usb3_lpm_parameters u2_params;
USB: Add support to enable/disable USB3 link states. There are various functions within the USB core that will need to disable USB 3.0 link power states. For example, when a USB device driver is being bound to an interface, we need to disable USB 3.0 LPM until we know if the driver will allow hub-initiated LPM transitions. Another example is when the USB core is switching alternate interface settings. The USB 3.0 timeout values are dependent on what endpoints are enabled, so we want to ensure that LPM is disabled until the new alt setting is fully installed. Multiple functions need to disable LPM, and those functions can even be nested. For example, usb_bind_interface() could disable LPM, and then call into the driver probe function, which may attempt to switch to a different alt setting. Therefore, we need to keep a count of the number of functions that require LPM to be disabled at any point in time. Introduce two new USB core API calls, usb_disable_lpm() and usb_enable_lpm(). These functions increment and decrement a new variable in the usb_device, lpm_disable_count. If usb_disable_lpm() fails, it will call usb_enable_lpm() in order to balance the lpm_disable_count. These two new functions must be called with the bandwidth_mutex locked. If the bandwidth_mutex is not already held by the caller, it should instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take the bandwidth_mutex before calling usb_disable_lpm() and usb_enable_lpm(), respectively. Introduce a new variable (timeout) in the usb3_lpm_params structure to keep track of the currently enabled U1/U2 timeout values. When usb_disable_lpm() is called, and the USB device has the U1 or U2 timeouts set to a non-zero value (meaning either device-initiated or hub-initiated LPM is enabled), attempt to disable LPM, regardless of the state of the lpm_disable_count. We want to ensure that all callers can be guaranteed that LPM is disabled if usb_disable_lpm() returns zero. Otherwise the following scenario could occur: 1. Driver A is being bound to interface 1. usb_probe_interface() disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so even though usb_disable_lpm() fails, the probe of the driver continues, and the bandwidth mutex is dropped. 2. Meanwhile, Driver B is being bound to interface 2. usb_probe_interface() grabs the bandwidth mutex and calls usb_disable_lpm(). That call should attempt to disable LPM, even though the lpm_disable_count is set to 1 by Driver A. For usb_enable_lpm(), we attempt to enable LPM only when the lpm_disable_count is zero. If some step in enabling LPM fails, it will only have a minimal impact on power consumption, and all USB device drivers should still work properly. Therefore don't bother to return any error codes. Don't enable device-initiated LPM if the device is unconfigured. The USB device will only accept the U1/U2_ENABLE control transfers in the configured state. Do enable hub-initiated LPM in that case, since devices are allowed to accept the LGO_Ux link commands in any state. Don't enable or disable LPM if the device is marked as not being LPM capable. This can happen if: - the USB device doesn't have a SS BOS descriptor, - the device's parent hub has a zeroed bHeaderDecodeLatency value, or - the xHCI host doesn't support LPM. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Andiry Xu <andiry.xu@amd.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-04-25 00:21:50 +00:00
unsigned lpm_disable_count;
u16 hub_delay;
};
#define to_usb_device(d) container_of(d, struct usb_device, dev)
static inline struct usb_device *interface_to_usbdev(struct usb_interface *intf)
{
return to_usb_device(intf->dev.parent);
}
extern struct usb_device *usb_get_dev(struct usb_device *dev);
extern void usb_put_dev(struct usb_device *dev);
extern struct usb_device *usb_hub_find_child(struct usb_device *hdev,
int port1);
/**
* usb_hub_for_each_child - iterate over all child devices on the hub
* @hdev: USB device belonging to the usb hub
* @port1: portnum associated with child device
* @child: child device pointer
*/
#define usb_hub_for_each_child(hdev, port1, child) \
for (port1 = 1, child = usb_hub_find_child(hdev, port1); \
port1 <= hdev->maxchild; \
child = usb_hub_find_child(hdev, ++port1)) \
if (!child) continue; else
/* USB device locking */
#define usb_lock_device(udev) device_lock(&(udev)->dev)
#define usb_unlock_device(udev) device_unlock(&(udev)->dev)
#define usb_lock_device_interruptible(udev) device_lock_interruptible(&(udev)->dev)
#define usb_trylock_device(udev) device_trylock(&(udev)->dev)
extern int usb_lock_device_for_reset(struct usb_device *udev,
const struct usb_interface *iface);
/* USB port reset for device reinitialization */
extern int usb_reset_device(struct usb_device *dev);
extern void usb_queue_reset_device(struct usb_interface *dev);
#ifdef CONFIG_ACPI
extern int usb_acpi_set_power_state(struct usb_device *hdev, int index,
bool enable);
extern bool usb_acpi_power_manageable(struct usb_device *hdev, int index);
#else
static inline int usb_acpi_set_power_state(struct usb_device *hdev, int index,
bool enable) { return 0; }
static inline bool usb_acpi_power_manageable(struct usb_device *hdev, int index)
{ return true; }
#endif
/* USB autosuspend and autoresume */
#ifdef CONFIG_PM
extern void usb_enable_autosuspend(struct usb_device *udev);
extern void usb_disable_autosuspend(struct usb_device *udev);
extern int usb_autopm_get_interface(struct usb_interface *intf);
extern void usb_autopm_put_interface(struct usb_interface *intf);
extern int usb_autopm_get_interface_async(struct usb_interface *intf);
extern void usb_autopm_put_interface_async(struct usb_interface *intf);
extern void usb_autopm_get_interface_no_resume(struct usb_interface *intf);
extern void usb_autopm_put_interface_no_suspend(struct usb_interface *intf);
static inline void usb_mark_last_busy(struct usb_device *udev)
{
pm_runtime_mark_last_busy(&udev->dev);
}
#else
static inline int usb_enable_autosuspend(struct usb_device *udev)
{ return 0; }
static inline int usb_disable_autosuspend(struct usb_device *udev)
{ return 0; }
static inline int usb_autopm_get_interface(struct usb_interface *intf)
{ return 0; }
static inline int usb_autopm_get_interface_async(struct usb_interface *intf)
{ return 0; }
static inline void usb_autopm_put_interface(struct usb_interface *intf)
{ }
static inline void usb_autopm_put_interface_async(struct usb_interface *intf)
{ }
static inline void usb_autopm_get_interface_no_resume(
struct usb_interface *intf)
{ }
static inline void usb_autopm_put_interface_no_suspend(
struct usb_interface *intf)
{ }
static inline void usb_mark_last_busy(struct usb_device *udev)
{ }
#endif
USB: Fix core compile with CONFIG_USB_SUSPEND=n When CONFIG_PM=n, make sure that the usb_[unlocked_][en/dis]able_lpm declarations are visible in include/linux/usb.h, and exported from drivers/usb/core/hub.c. Before this patch, if CONFIG_USB_SUSPEND was turned off, it would cause build errors: drivers/usb/core/hub.c: In function 'usb_disable_lpm': drivers/usb/core/hub.c:3394:2: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/hub.c: At top level: drivers/usb/core/hub.c:3424:6: warning: conflicting types for 'usb_enable_lpm' [enabled by default] drivers/usb/core/hub.c:3394:2: note: previous implicit declaration of 'usb_enable_lpm' was here drivers/usb/core/driver.c: In function 'usb_probe_interface': drivers/usb/core/driver.c:339:2: error: implicit declaration of function 'usb_unlocked_disable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/driver.c:364:3: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/message.c: In function 'usb_set_interface': drivers/usb/core/message.c:1314:2: error: implicit declaration of function 'usb_disable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/message.c:1323:3: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/message.c:1368:2: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration] Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: Chen Peter-B29397 <B29397@freescale.com>
2012-05-21 15:29:01 +00:00
extern int usb_disable_lpm(struct usb_device *udev);
extern void usb_enable_lpm(struct usb_device *udev);
/* Same as above, but these functions lock/unlock the bandwidth_mutex. */
extern int usb_unlocked_disable_lpm(struct usb_device *udev);
extern void usb_unlocked_enable_lpm(struct usb_device *udev);
USB: Enable Latency Tolerance Messaging (LTM). USB 3.0 devices may optionally support a new feature called Latency Tolerance Messaging. If both the xHCI host controller and the device support LTM, it should be turned on in order to give the system hardware a better clue about the latency tolerance values of its PCI devices. Once a Set Feature request to enable LTM is received, the USB 3.0 device will begin to send LTM updates as its buffers fill or empty, and it can tolerate more or less latency. The USB 3.0 spec, section C.4.2 says that LTM should be disabled just before the device is placed into suspend. Then the device will send an updated LTM notification, so that the system doesn't think it should remain in an active state in order to satisfy the latency requirements of the suspended device. The Set and Clear Feature LTM enable command can only be sent to a configured device. The device will respond with an error if that command is sent while it is in the Default or Addressed state. Make sure to check udev->actconfig in usb_enable_ltm() and usb_disable_ltm(), and don't send those commands when the device is unconfigured. LTM should be enabled once a new configuration is installed in usb_set_configuration(). If we end up sending duplicate Set Feature LTM Enable commands on a switch from one installed configuration to another configuration, that should be harmless. Make sure that LTM is disabled before the device is unconfigured in usb_disable_device(). If no drivers are bound to the device, it doesn't make sense to allow the device to control the latency tolerance of the xHCI host controller. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-06-25 19:08:08 +00:00
extern int usb_disable_ltm(struct usb_device *udev);
extern void usb_enable_ltm(struct usb_device *udev);
static inline bool usb_device_supports_ltm(struct usb_device *udev)
{
if (udev->speed < USB_SPEED_SUPER || !udev->bos || !udev->bos->ss_cap)
return false;
return udev->bos->ss_cap->bmAttributes & USB_LTM_SUPPORT;
}
static inline bool usb_device_no_sg_constraint(struct usb_device *udev)
{
return udev && udev->bus && udev->bus->no_sg_constraint;
}
/*-------------------------------------------------------------------------*/
/* for drivers using iso endpoints */
extern int usb_get_current_frame_number(struct usb_device *usb_dev);
/* Sets up a group of bulk endpoints to support multiple stream IDs. */
extern int usb_alloc_streams(struct usb_interface *interface,
struct usb_host_endpoint **eps, unsigned int num_eps,
unsigned int num_streams, gfp_t mem_flags);
/* Reverts a group of bulk endpoints back to not using stream IDs. */
extern int usb_free_streams(struct usb_interface *interface,
struct usb_host_endpoint **eps, unsigned int num_eps,
gfp_t mem_flags);
/* used these for multi-interface device registration */
extern int usb_driver_claim_interface(struct usb_driver *driver,
struct usb_interface *iface, void *priv);
/**
* usb_interface_claimed - returns true iff an interface is claimed
* @iface: the interface being checked
*
* Return: %true (nonzero) iff the interface is claimed, else %false
* (zero).
*
* Note:
* Callers must own the driver model's usb bus readlock. So driver
* probe() entries don't need extra locking, but other call contexts
* may need to explicitly claim that lock.
*
*/
static inline int usb_interface_claimed(struct usb_interface *iface)
{
return (iface->dev.driver != NULL);
}
extern void usb_driver_release_interface(struct usb_driver *driver,
struct usb_interface *iface);
const struct usb_device_id *usb_match_id(struct usb_interface *interface,
const struct usb_device_id *id);
extern int usb_match_one_id(struct usb_interface *interface,
const struct usb_device_id *id);
extern int usb_for_each_dev(void *data, int (*fn)(struct usb_device *, void *));
extern struct usb_interface *usb_find_interface(struct usb_driver *drv,
int minor);
extern struct usb_interface *usb_ifnum_to_if(const struct usb_device *dev,
unsigned ifnum);
extern struct usb_host_interface *usb_altnum_to_altsetting(
const struct usb_interface *intf, unsigned int altnum);
extern struct usb_host_interface *usb_find_alt_setting(
struct usb_host_config *config,
unsigned int iface_num,
unsigned int alt_num);
/* port claiming functions */
int usb_hub_claim_port(struct usb_device *hdev, unsigned port1,
struct usb_dev_state *owner);
int usb_hub_release_port(struct usb_device *hdev, unsigned port1,
struct usb_dev_state *owner);
/**
* usb_make_path - returns stable device path in the usb tree
* @dev: the device whose path is being constructed
* @buf: where to put the string
* @size: how big is "buf"?
*
* Return: Length of the string (> 0) or negative if size was too small.
*
* Note:
* This identifier is intended to be "stable", reflecting physical paths in
* hardware such as physical bus addresses for host controllers or ports on
* USB hubs. That makes it stay the same until systems are physically
* reconfigured, by re-cabling a tree of USB devices or by moving USB host
* controllers. Adding and removing devices, including virtual root hubs
* in host controller driver modules, does not change these path identifiers;
* neither does rebooting or re-enumerating. These are more useful identifiers
* than changeable ("unstable") ones like bus numbers or device addresses.
*
* With a partial exception for devices connected to USB 2.0 root hubs, these
* identifiers are also predictable. So long as the device tree isn't changed,
* plugging any USB device into a given hub port always gives it the same path.
* Because of the use of "companion" controllers, devices connected to ports on
* USB 2.0 root hubs (EHCI host controllers) will get one path ID if they are
* high speed, and a different one if they are full or low speed.
*/
static inline int usb_make_path(struct usb_device *dev, char *buf, size_t size)
{
int actual;
actual = snprintf(buf, size, "usb-%s-%s", dev->bus->bus_name,
dev->devpath);
return (actual >= (int)size) ? -1 : actual;
}
/*-------------------------------------------------------------------------*/
#define USB_DEVICE_ID_MATCH_DEVICE \
(USB_DEVICE_ID_MATCH_VENDOR | USB_DEVICE_ID_MATCH_PRODUCT)
#define USB_DEVICE_ID_MATCH_DEV_RANGE \
(USB_DEVICE_ID_MATCH_DEV_LO | USB_DEVICE_ID_MATCH_DEV_HI)
#define USB_DEVICE_ID_MATCH_DEVICE_AND_VERSION \
(USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_DEV_RANGE)
#define USB_DEVICE_ID_MATCH_DEV_INFO \
(USB_DEVICE_ID_MATCH_DEV_CLASS | \
USB_DEVICE_ID_MATCH_DEV_SUBCLASS | \
USB_DEVICE_ID_MATCH_DEV_PROTOCOL)
#define USB_DEVICE_ID_MATCH_INT_INFO \
(USB_DEVICE_ID_MATCH_INT_CLASS | \
USB_DEVICE_ID_MATCH_INT_SUBCLASS | \
USB_DEVICE_ID_MATCH_INT_PROTOCOL)
/**
* USB_DEVICE - macro used to describe a specific usb device
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
*
* This macro is used to create a struct usb_device_id that matches a
* specific device.
*/
#define USB_DEVICE(vend, prod) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE, \
.idVendor = (vend), \
.idProduct = (prod)
/**
* USB_DEVICE_VER - describe a specific usb device with a version range
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @lo: the bcdDevice_lo value
* @hi: the bcdDevice_hi value
*
* This macro is used to create a struct usb_device_id that matches a
* specific device, with a version range.
*/
#define USB_DEVICE_VER(vend, prod, lo, hi) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE_AND_VERSION, \
.idVendor = (vend), \
.idProduct = (prod), \
.bcdDevice_lo = (lo), \
.bcdDevice_hi = (hi)
/**
* USB_DEVICE_INTERFACE_CLASS - describe a usb device with a specific interface class
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @cl: bInterfaceClass value
*
* This macro is used to create a struct usb_device_id that matches a
* specific interface class of devices.
*/
#define USB_DEVICE_INTERFACE_CLASS(vend, prod, cl) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE | \
USB_DEVICE_ID_MATCH_INT_CLASS, \
.idVendor = (vend), \
.idProduct = (prod), \
.bInterfaceClass = (cl)
/**
* USB_DEVICE_INTERFACE_PROTOCOL - describe a usb device with a specific interface protocol
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @pr: bInterfaceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific interface protocol of devices.
*/
#define USB_DEVICE_INTERFACE_PROTOCOL(vend, prod, pr) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE | \
USB_DEVICE_ID_MATCH_INT_PROTOCOL, \
.idVendor = (vend), \
.idProduct = (prod), \
.bInterfaceProtocol = (pr)
/**
* USB_DEVICE_INTERFACE_NUMBER - describe a usb device with a specific interface number
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @num: bInterfaceNumber value
*
* This macro is used to create a struct usb_device_id that matches a
* specific interface number of devices.
*/
#define USB_DEVICE_INTERFACE_NUMBER(vend, prod, num) \
.match_flags = USB_DEVICE_ID_MATCH_DEVICE | \
USB_DEVICE_ID_MATCH_INT_NUMBER, \
.idVendor = (vend), \
.idProduct = (prod), \
.bInterfaceNumber = (num)
/**
* USB_DEVICE_INFO - macro used to describe a class of usb devices
* @cl: bDeviceClass value
* @sc: bDeviceSubClass value
* @pr: bDeviceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific class of devices.
*/
#define USB_DEVICE_INFO(cl, sc, pr) \
.match_flags = USB_DEVICE_ID_MATCH_DEV_INFO, \
.bDeviceClass = (cl), \
.bDeviceSubClass = (sc), \
.bDeviceProtocol = (pr)
/**
* USB_INTERFACE_INFO - macro used to describe a class of usb interfaces
* @cl: bInterfaceClass value
* @sc: bInterfaceSubClass value
* @pr: bInterfaceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific class of interfaces.
*/
#define USB_INTERFACE_INFO(cl, sc, pr) \
.match_flags = USB_DEVICE_ID_MATCH_INT_INFO, \
.bInterfaceClass = (cl), \
.bInterfaceSubClass = (sc), \
.bInterfaceProtocol = (pr)
/**
* USB_DEVICE_AND_INTERFACE_INFO - describe a specific usb device with a class of usb interfaces
* @vend: the 16 bit USB Vendor ID
* @prod: the 16 bit USB Product ID
* @cl: bInterfaceClass value
* @sc: bInterfaceSubClass value
* @pr: bInterfaceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific device with a specific class of interfaces.
*
* This is especially useful when explicitly matching devices that have
* vendor specific bDeviceClass values, but standards-compliant interfaces.
*/
#define USB_DEVICE_AND_INTERFACE_INFO(vend, prod, cl, sc, pr) \
.match_flags = USB_DEVICE_ID_MATCH_INT_INFO \
| USB_DEVICE_ID_MATCH_DEVICE, \
.idVendor = (vend), \
.idProduct = (prod), \
.bInterfaceClass = (cl), \
.bInterfaceSubClass = (sc), \
.bInterfaceProtocol = (pr)
/**
* USB_VENDOR_AND_INTERFACE_INFO - describe a specific usb vendor with a class of usb interfaces
* @vend: the 16 bit USB Vendor ID
* @cl: bInterfaceClass value
* @sc: bInterfaceSubClass value
* @pr: bInterfaceProtocol value
*
* This macro is used to create a struct usb_device_id that matches a
* specific vendor with a specific class of interfaces.
*
* This is especially useful when explicitly matching devices that have
* vendor specific bDeviceClass values, but standards-compliant interfaces.
*/
#define USB_VENDOR_AND_INTERFACE_INFO(vend, cl, sc, pr) \
.match_flags = USB_DEVICE_ID_MATCH_INT_INFO \
| USB_DEVICE_ID_MATCH_VENDOR, \
.idVendor = (vend), \
.bInterfaceClass = (cl), \
.bInterfaceSubClass = (sc), \
.bInterfaceProtocol = (pr)
/* ----------------------------------------------------------------------- */
/* Stuff for dynamic usb ids */
struct usb_dynids {
spinlock_t lock;
struct list_head list;
};
struct usb_dynid {
struct list_head node;
struct usb_device_id id;
};
extern ssize_t usb_store_new_id(struct usb_dynids *dynids,
const struct usb_device_id *id_table,
struct device_driver *driver,
const char *buf, size_t count);
extern ssize_t usb_show_dynids(struct usb_dynids *dynids, char *buf);
/**
* struct usbdrv_wrap - wrapper for driver-model structure
* @driver: The driver-model core driver structure.
* @for_devices: Non-zero for device drivers, 0 for interface drivers.
*/
struct usbdrv_wrap {
struct device_driver driver;
int for_devices;
};
/**
* struct usb_driver - identifies USB interface driver to usbcore
* @name: The driver name should be unique among USB drivers,
* and should normally be the same as the module name.
* @probe: Called to see if the driver is willing to manage a particular
* interface on a device. If it is, probe returns zero and uses
* usb_set_intfdata() to associate driver-specific data with the
* interface. It may also use usb_set_interface() to specify the
* appropriate altsetting. If unwilling to manage the interface,
* return -ENODEV, if genuine IO errors occurred, an appropriate
* negative errno value.
* @disconnect: Called when the interface is no longer accessible, usually
* because its device has been (or is being) disconnected or the
* driver module is being unloaded.
* @unlocked_ioctl: Used for drivers that want to talk to userspace through
* the "usbfs" filesystem. This lets devices provide ways to
* expose information to user space regardless of where they
* do (or don't) show up otherwise in the filesystem.
* @suspend: Called when the device is going to be suspended by the
* system either from system sleep or runtime suspend context. The
* return value will be ignored in system sleep context, so do NOT
* try to continue using the device if suspend fails in this case.
* Instead, let the resume or reset-resume routine recover from
* the failure.
* @resume: Called when the device is being resumed by the system.
USB: add reset_resume method This patch (as918) introduces a new USB driver method: reset_resume. It is called when a device needs to be reset as part of a resume procedure (whether because of a device quirk or because of the USB-Persist facility), thereby taking over a role formerly assigned to the post_reset method. As a consequence, post_reset no longer needs an argument indicating whether it is being called as part of a reset-resume. This separation of functions makes the code clearer. In addition, the pre_reset and post_reset method return types are changed; they now must return an error code. The return value is unused at present, but at some later time we may unbind drivers and re-probe if they encounter an error during reset handling. The existing pre_reset and post_reset methods in the usbhid, usb-storage, and hub drivers are updated to match the new requirements. For usbhid the post_reset routine is also used for reset_resume (duplicate method pointers); for the other drivers a new reset_resume routine is added. The change to hub.c looks bigger than it really is, because mark_children_for_reset_resume() gets moved down next to the new hub_reset_resume() routine. A minor change to usb-storage makes the usb_stor_report_bus_reset() routine acquire the host lock instead of requiring the caller to hold it already. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-30 19:38:16 +00:00
* @reset_resume: Called when the suspended device has been reset instead
* of being resumed.
* @pre_reset: Called by usb_reset_device() when the device is about to be
* reset. This routine must not return until the driver has no active
* URBs for the device, and no more URBs may be submitted until the
* post_reset method is called.
* @post_reset: Called by usb_reset_device() after the device
* has been reset
* @id_table: USB drivers use ID table to support hotplugging.
* Export this with MODULE_DEVICE_TABLE(usb,...). This must be set
* or your driver's probe function will never get called.
* @dynids: used internally to hold the list of dynamically added device
* ids for this driver.
* @drvwrap: Driver-model core structure wrapper.
* @no_dynamic_id: if set to 1, the USB core will not allow dynamic ids to be
* added to this driver by preventing the sysfs file from being created.
* @supports_autosuspend: if set to 0, the USB core will not allow autosuspend
* for interfaces bound to this driver.
* @soft_unbind: if set to 1, the USB core will not kill URBs and disable
* endpoints before calling the driver's disconnect method.
USB: leave LPM alone if possible when binding/unbinding interface drivers When a USB driver is bound to an interface (either through probing or by claiming it) or is unbound from an interface, the USB core always disables Link Power Management during the transition and then re-enables it afterward. The reason is because the driver might want to prevent hub-initiated link power transitions, in which case the HCD would have to recalculate the various LPM parameters. This recalculation takes place when LPM is re-enabled and the new parameters are sent to the device and its parent hub. However, if the driver does not want to prevent hub-initiated link power transitions then none of this work is necessary. The parameters don't need to be recalculated, and LPM doesn't need to be disabled and re-enabled. It turns out that disabling and enabling LPM can be time-consuming, enough so that it interferes with user programs that want to claim and release interfaces rapidly via usbfs. Since the usbfs kernel driver doesn't set the disable_hub_initiated_lpm flag, we can speed things up and get the user programs to work by leaving LPM alone whenever the flag isn't set. And while we're improving the way disable_hub_initiated_lpm gets used, let's also fix its kerneldoc. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Matthew Giassa <matthew@giassa.net> CC: Mathias Nyman <mathias.nyman@intel.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-29 19:25:17 +00:00
* @disable_hub_initiated_lpm: if set to 1, the USB core will not allow hubs
USB: Allow drivers to disable hub-initiated LPM. USB 3.0 Link Power Management (LPM) is designed to allow individual links in the bus to go into lower power states. There are two ways a link can enter a lower power state: 1. Device-initiated LPM. When a USB device decides it can go into a lower power link state, it sends a message to the parent hub, telling it to go into either U1 or U2. Device-initiated LPM is good for devices that send data to the host, like communications devices. 2. Hub-initiated LPM. After the link has been idle for a specific amount of time, the parent hub will request that the child go into a lower power state. The child can refuse that request. For example, a USB modem may want to refuse the LPM request if it is in the middle of receiving a text message. Hub-initiated LPM is good for devices where only the host initiates the data transfer, like USB printers or USB mass storage devices. Links will be automatically placed into higher power states by the USB hubs and roothubs whenever the host starts a USB transmission. Introduce a new usb_driver flag, disable_hub_initiated_lpm, that allows drivers to disable hub-initiated LPM. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Oliver Neukum <oliver@neukum.name> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Cc: linux-bluetooth@vger.kernel.org Cc: gigaset307x-common@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-usb@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: ath9k-devel@lists.ath9k.org Cc: libertas-dev@lists.infradead.org Cc: users@rt2x00.serialmonkey.com
2012-04-23 17:08:51 +00:00
* to initiate lower power link state transitions when an idle timeout
* occurs. Device-initiated USB 3.0 link PM will still be allowed.
*
* USB interface drivers must provide a name, probe() and disconnect()
* methods, and an id_table. Other driver fields are optional.
*
* The id_table is used in hotplugging. It holds a set of descriptors,
* and specialized data may be associated with each entry. That table
* is used by both user and kernel mode hotplugging support.
*
* The probe() and disconnect() methods are called in a context where
* they can sleep, but they should avoid abusing the privilege. Most
* work to connect to a device should be done when the device is opened,
* and undone at the last close. The disconnect code needs to address
* concurrency issues with respect to open() and close() methods, as
* well as forcing all pending I/O requests to complete (by unlinking
* them as necessary, and blocking until the unlinks complete).
*/
struct usb_driver {
const char *name;
int (*probe) (struct usb_interface *intf,
const struct usb_device_id *id);
void (*disconnect) (struct usb_interface *intf);
int (*unlocked_ioctl) (struct usb_interface *intf, unsigned int code,
void *buf);
int (*suspend) (struct usb_interface *intf, pm_message_t message);
int (*resume) (struct usb_interface *intf);
USB: add reset_resume method This patch (as918) introduces a new USB driver method: reset_resume. It is called when a device needs to be reset as part of a resume procedure (whether because of a device quirk or because of the USB-Persist facility), thereby taking over a role formerly assigned to the post_reset method. As a consequence, post_reset no longer needs an argument indicating whether it is being called as part of a reset-resume. This separation of functions makes the code clearer. In addition, the pre_reset and post_reset method return types are changed; they now must return an error code. The return value is unused at present, but at some later time we may unbind drivers and re-probe if they encounter an error during reset handling. The existing pre_reset and post_reset methods in the usbhid, usb-storage, and hub drivers are updated to match the new requirements. For usbhid the post_reset routine is also used for reset_resume (duplicate method pointers); for the other drivers a new reset_resume routine is added. The change to hub.c looks bigger than it really is, because mark_children_for_reset_resume() gets moved down next to the new hub_reset_resume() routine. A minor change to usb-storage makes the usb_stor_report_bus_reset() routine acquire the host lock instead of requiring the caller to hold it already. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-30 19:38:16 +00:00
int (*reset_resume)(struct usb_interface *intf);
USB: add reset_resume method This patch (as918) introduces a new USB driver method: reset_resume. It is called when a device needs to be reset as part of a resume procedure (whether because of a device quirk or because of the USB-Persist facility), thereby taking over a role formerly assigned to the post_reset method. As a consequence, post_reset no longer needs an argument indicating whether it is being called as part of a reset-resume. This separation of functions makes the code clearer. In addition, the pre_reset and post_reset method return types are changed; they now must return an error code. The return value is unused at present, but at some later time we may unbind drivers and re-probe if they encounter an error during reset handling. The existing pre_reset and post_reset methods in the usbhid, usb-storage, and hub drivers are updated to match the new requirements. For usbhid the post_reset routine is also used for reset_resume (duplicate method pointers); for the other drivers a new reset_resume routine is added. The change to hub.c looks bigger than it really is, because mark_children_for_reset_resume() gets moved down next to the new hub_reset_resume() routine. A minor change to usb-storage makes the usb_stor_report_bus_reset() routine acquire the host lock instead of requiring the caller to hold it already. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-30 19:38:16 +00:00
int (*pre_reset)(struct usb_interface *intf);
int (*post_reset)(struct usb_interface *intf);
const struct usb_device_id *id_table;
struct usb_dynids dynids;
struct usbdrv_wrap drvwrap;
unsigned int no_dynamic_id:1;
unsigned int supports_autosuspend:1;
USB: Allow drivers to disable hub-initiated LPM. USB 3.0 Link Power Management (LPM) is designed to allow individual links in the bus to go into lower power states. There are two ways a link can enter a lower power state: 1. Device-initiated LPM. When a USB device decides it can go into a lower power link state, it sends a message to the parent hub, telling it to go into either U1 or U2. Device-initiated LPM is good for devices that send data to the host, like communications devices. 2. Hub-initiated LPM. After the link has been idle for a specific amount of time, the parent hub will request that the child go into a lower power state. The child can refuse that request. For example, a USB modem may want to refuse the LPM request if it is in the middle of receiving a text message. Hub-initiated LPM is good for devices where only the host initiates the data transfer, like USB printers or USB mass storage devices. Links will be automatically placed into higher power states by the USB hubs and roothubs whenever the host starts a USB transmission. Introduce a new usb_driver flag, disable_hub_initiated_lpm, that allows drivers to disable hub-initiated LPM. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Oliver Neukum <oliver@neukum.name> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Cc: linux-bluetooth@vger.kernel.org Cc: gigaset307x-common@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-usb@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: ath9k-devel@lists.ath9k.org Cc: libertas-dev@lists.infradead.org Cc: users@rt2x00.serialmonkey.com
2012-04-23 17:08:51 +00:00
unsigned int disable_hub_initiated_lpm:1;
unsigned int soft_unbind:1;
};
#define to_usb_driver(d) container_of(d, struct usb_driver, drvwrap.driver)
/**
* struct usb_device_driver - identifies USB device driver to usbcore
* @name: The driver name should be unique among USB drivers,
* and should normally be the same as the module name.
* @probe: Called to see if the driver is willing to manage a particular
* device. If it is, probe returns zero and uses dev_set_drvdata()
* to associate driver-specific data with the device. If unwilling
* to manage the device, return a negative errno value.
* @disconnect: Called when the device is no longer accessible, usually
* because it has been (or is being) disconnected or the driver's
* module is being unloaded.
* @suspend: Called when the device is going to be suspended by the system.
* @resume: Called when the device is being resumed by the system.
* @drvwrap: Driver-model core structure wrapper.
* @supports_autosuspend: if set to 0, the USB core will not allow autosuspend
* for devices bound to this driver.
*
* USB drivers must provide all the fields listed above except drvwrap.
*/
struct usb_device_driver {
const char *name;
int (*probe) (struct usb_device *udev);
void (*disconnect) (struct usb_device *udev);
int (*suspend) (struct usb_device *udev, pm_message_t message);
int (*resume) (struct usb_device *udev, pm_message_t message);
struct usbdrv_wrap drvwrap;
unsigned int supports_autosuspend:1;
};
#define to_usb_device_driver(d) container_of(d, struct usb_device_driver, \
drvwrap.driver)
extern struct bus_type usb_bus_type;
/**
* struct usb_class_driver - identifies a USB driver that wants to use the USB major number
* @name: the usb class device name for this driver. Will show up in sysfs.
* @devnode: Callback to provide a naming hint for a possible
* device node to create.
* @fops: pointer to the struct file_operations of this driver.
* @minor_base: the start of the minor range for this driver.
*
* This structure is used for the usb_register_dev() and
* usb_deregister_dev() functions, to consolidate a number of the
* parameters used for them.
*/
struct usb_class_driver {
char *name;
char *(*devnode)(struct device *dev, umode_t *mode);
const struct file_operations *fops;
int minor_base;
};
/*
* use these in module_init()/module_exit()
* and don't forget MODULE_DEVICE_TABLE(usb, ...)
*/
extern int usb_register_driver(struct usb_driver *, struct module *,
const char *);
/* use a define to avoid include chaining to get THIS_MODULE & friends */
#define usb_register(driver) \
usb_register_driver(driver, THIS_MODULE, KBUILD_MODNAME)
extern void usb_deregister(struct usb_driver *);
/**
* module_usb_driver() - Helper macro for registering a USB driver
* @__usb_driver: usb_driver struct
*
* Helper macro for USB drivers which do not do anything special in module
* init/exit. This eliminates a lot of boilerplate. Each module may only
* use this macro once, and calling it replaces module_init() and module_exit()
*/
#define module_usb_driver(__usb_driver) \
module_driver(__usb_driver, usb_register, \
usb_deregister)
extern int usb_register_device_driver(struct usb_device_driver *,
struct module *);
extern void usb_deregister_device_driver(struct usb_device_driver *);
extern int usb_register_dev(struct usb_interface *intf,
struct usb_class_driver *class_driver);
extern void usb_deregister_dev(struct usb_interface *intf,
struct usb_class_driver *class_driver);
extern int usb_disabled(void);
/* ----------------------------------------------------------------------- */
/*
* URB support, for asynchronous request completions
*/
/*
* urb->transfer_flags:
*
* Note: URB_DIR_IN/OUT is automatically set in usb_submit_urb().
*/
#define URB_SHORT_NOT_OK 0x0001 /* report short reads as errors */
#define URB_ISO_ASAP 0x0002 /* iso-only; use the first unexpired
* slot in the schedule */
#define URB_NO_TRANSFER_DMA_MAP 0x0004 /* urb->transfer_dma valid on submit */
#define URB_ZERO_PACKET 0x0040 /* Finish bulk OUT with short packet */
#define URB_NO_INTERRUPT 0x0080 /* HINT: no non-error interrupt
* needed */
#define URB_FREE_BUFFER 0x0100 /* Free transfer buffer with the URB */
2010-04-02 17:27:28 +00:00
/* The following flags are used internally by usbcore and HCDs */
#define URB_DIR_IN 0x0200 /* Transfer from device to host */
#define URB_DIR_OUT 0
#define URB_DIR_MASK URB_DIR_IN
2010-04-02 17:27:28 +00:00
#define URB_DMA_MAP_SINGLE 0x00010000 /* Non-scatter-gather mapping */
#define URB_DMA_MAP_PAGE 0x00020000 /* HCD-unsupported S-G */
#define URB_DMA_MAP_SG 0x00040000 /* HCD-supported S-G */
#define URB_MAP_LOCAL 0x00080000 /* HCD-local-memory mapping */
#define URB_SETUP_MAP_SINGLE 0x00100000 /* Setup packet DMA mapped */
#define URB_SETUP_MAP_LOCAL 0x00200000 /* HCD-local setup packet */
#define URB_DMA_SG_COMBINED 0x00400000 /* S-G entries were combined */
#define URB_ALIGNED_TEMP_BUFFER 0x00800000 /* Temp buffer was alloc'd */
2010-04-02 17:27:28 +00:00
struct usb_iso_packet_descriptor {
unsigned int offset;
unsigned int length; /* expected length */
unsigned int actual_length;
int status;
};
struct urb;
struct usb_anchor {
struct list_head urb_list;
wait_queue_head_t wait;
spinlock_t lock;
usb-anchor: Delay usb_wait_anchor_empty_timeout wake up till completion is done usb_wait_anchor_empty_timeout() should wait till the completion handler has run. Both the zd1211rw driver and the uas driver (in its task mgmt) depend on the completion handler having completed when usb_wait_anchor_empty_timeout() returns, as they read state set by the completion handler after an usb_wait_anchor_empty_timeout() call. But __usb_hcd_giveback_urb() calls usb_unanchor_urb before calling the completion handler. This is necessary as the completion handler may re-submit and re-anchor the urb. But this introduces a race where the state these drivers want to read has not been set yet by the completion handler (this race is easily triggered with the uas task mgmt code). I've considered adding an anchor_count to struct urb, which would be incremented on anchor and decremented on unanchor, and then only actually do the anchor / unanchor on 0 -> 1 and 1 -> 0 transtions, combined with moving the unanchor call in hcd_giveback_urb to after calling the completion handler. But this will only work if urb's are only re-anchored to the same anchor as they were anchored to before the completion handler ran. And at least one driver re-anchors to another anchor from the completion handler (rtlwifi). So I have come up with this patch instead, which adds the ability to suspend wakeups of usb_wait_anchor_empty_timeout() waiters to the usb_anchor functionality, and uses this in __usb_hcd_giveback_urb() to delay wake-ups until the completion handler has run. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-09 15:01:41 +00:00
atomic_t suspend_wakeups;
unsigned int poisoned:1;
};
static inline void init_usb_anchor(struct usb_anchor *anchor)
{
memset(anchor, 0, sizeof(*anchor));
INIT_LIST_HEAD(&anchor->urb_list);
init_waitqueue_head(&anchor->wait);
spin_lock_init(&anchor->lock);
}
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 13:55:46 +00:00
typedef void (*usb_complete_t)(struct urb *);
/**
* struct urb - USB Request Block
* @urb_list: For use by current owner of the URB.
* @anchor_list: membership in the list of an anchor
* @anchor: to anchor URBs to a common mooring
* @ep: Points to the endpoint's data structure. Will eventually
* replace @pipe.
* @pipe: Holds endpoint number, direction, type, and more.
* Create these values with the eight macros available;
* usb_{snd,rcv}TYPEpipe(dev,endpoint), where the TYPE is "ctrl"
* (control), "bulk", "int" (interrupt), or "iso" (isochronous).
* For example usb_sndbulkpipe() or usb_rcvintpipe(). Endpoint
* numbers range from zero to fifteen. Note that "in" endpoint two
* is a different endpoint (and pipe) from "out" endpoint two.
* The current configuration controls the existence, type, and
* maximum packet size of any given endpoint.
* @stream_id: the endpoint's stream ID for bulk streams
* @dev: Identifies the USB device to perform the request.
* @status: This is read in non-iso completion functions to get the
* status of the particular request. ISO requests only use it
* to tell whether the URB was unlinked; detailed status for
* each frame is in the fields of the iso_frame-desc.
* @transfer_flags: A variety of flags may be used to affect how URB
* submission, unlinking, or operation are handled. Different
* kinds of URB can use different flags.
2009-06-11 14:53:20 +00:00
* @transfer_buffer: This identifies the buffer to (or from) which the I/O
* request will be performed unless URB_NO_TRANSFER_DMA_MAP is set
* (however, do not leave garbage in transfer_buffer even then).
* This buffer must be suitable for DMA; allocate it with
* kmalloc() or equivalent. For transfers to "in" endpoints, contents
* of this buffer will be modified. This buffer is used for the data
* stage of control transfers.
* @transfer_dma: When transfer_flags includes URB_NO_TRANSFER_DMA_MAP,
* the device driver is saying that it provided this DMA address,
* which the host controller driver should use in preference to the
* transfer_buffer.
* @sg: scatter gather buffer list, the buffer size of each element in
* the list (except the last) must be divisible by the endpoint's
* max packet size if no_sg_constraint isn't set in 'struct usb_bus'
* @num_mapped_sgs: (internal) number of mapped sg entries
* @num_sgs: number of entries in the sg list
* @transfer_buffer_length: How big is transfer_buffer. The transfer may
* be broken up into chunks according to the current maximum packet
* size for the endpoint, which is a function of the configuration
* and is encoded in the pipe. When the length is zero, neither
* transfer_buffer nor transfer_dma is used.
* @actual_length: This is read in non-iso completion functions, and
* it tells how many bytes (out of transfer_buffer_length) were
* transferred. It will normally be the same as requested, unless
* either an error was reported or a short read was performed.
* The URB_SHORT_NOT_OK transfer flag may be used to make such
* short reads be reported as errors.
* @setup_packet: Only used for control transfers, this points to eight bytes
* of setup data. Control transfers always start by sending this data
* to the device. Then transfer_buffer is read or written, if needed.
* @setup_dma: DMA pointer for the setup packet. The caller must not use
* this field; setup_packet must point to a valid buffer.
* @start_frame: Returns the initial frame for isochronous transfers.
* @number_of_packets: Lists the number of ISO transfer buffers.
* @interval: Specifies the polling interval for interrupt or isochronous
* transfers. The units are frames (milliseconds) for full and low
* speed devices, and microframes (1/8 millisecond) for highspeed
* and SuperSpeed devices.
* @error_count: Returns the number of ISO transfers that reported errors.
* @context: For use in completion functions. This normally points to
* request-specific driver context.
* @complete: Completion handler. This URB is passed as the parameter to the
* completion function. The completion function may then do what
* it likes with the URB, including resubmitting or freeing it.
* @iso_frame_desc: Used to provide arrays of ISO transfer buffers and to
* collect the transfer status for each buffer.
*
* This structure identifies USB transfer requests. URBs must be allocated by
* calling usb_alloc_urb() and freed with a call to usb_free_urb().
* Initialization may be done using various usb_fill_*_urb() functions. URBs
* are submitted using usb_submit_urb(), and pending requests may be canceled
* using usb_unlink_urb() or usb_kill_urb().
*
* Data Transfer Buffers:
*
* Normally drivers provide I/O buffers allocated with kmalloc() or otherwise
* taken from the general page pool. That is provided by transfer_buffer
* (control requests also use setup_packet), and host controller drivers
* perform a dma mapping (and unmapping) for each buffer transferred. Those
* mapping operations can be expensive on some platforms (perhaps using a dma
* bounce buffer or talking to an IOMMU),
* although they're cheap on commodity x86 and ppc hardware.
*
* Alternatively, drivers may pass the URB_NO_TRANSFER_DMA_MAP transfer flag,
* which tells the host controller driver that no such mapping is needed for
* the transfer_buffer since
* the device driver is DMA-aware. For example, a device driver might
* allocate a DMA buffer with usb_alloc_coherent() or call usb_buffer_map().
* When this transfer flag is provided, host controller drivers will
* attempt to use the dma address found in the transfer_dma
* field rather than determining a dma address themselves.
2009-06-11 14:53:20 +00:00
*
* Note that transfer_buffer must still be set if the controller
* does not support DMA (as indicated by bus.uses_dma) and when talking
* to root hub. If you have to trasfer between highmem zone and the device
* on such controller, create a bounce buffer or bail out with an error.
* If transfer_buffer cannot be set (is in highmem) and the controller is DMA
* capable, assign NULL to it, so that usbmon knows not to use the value.
* The setup_packet must always be set, so it cannot be located in highmem.
*
* Initialization:
*
* All URBs submitted must initialize the dev, pipe, transfer_flags (may be
* zero), and complete fields. All URBs must also initialize
* transfer_buffer and transfer_buffer_length. They may provide the
* URB_SHORT_NOT_OK transfer flag, indicating that short reads are
* to be treated as errors; that flag is invalid for write requests.
*
* Bulk URBs may
* use the URB_ZERO_PACKET transfer flag, indicating that bulk OUT transfers
* should always terminate with a short packet, even if it means adding an
* extra zero length packet.
*
* Control URBs must provide a valid pointer in the setup_packet field.
* Unlike the transfer_buffer, the setup_packet may not be mapped for DMA
* beforehand.
*
* Interrupt URBs must provide an interval, saying how often (in milliseconds
* or, for highspeed devices, 125 microsecond units)
* to poll for transfers. After the URB has been submitted, the interval
* field reflects how the transfer was actually scheduled.
* The polling interval may be more frequent than requested.
* For example, some controllers have a maximum interval of 32 milliseconds,
* while others support intervals of up to 1024 milliseconds.
* Isochronous URBs also have transfer intervals. (Note that for isochronous
* endpoints, as well as high speed interrupt endpoints, the encoding of
* the transfer interval in the endpoint descriptor is logarithmic.
* Device drivers must convert that value to linear units themselves.)
*
* If an isochronous endpoint queue isn't already running, the host
* controller will schedule a new URB to start as soon as bandwidth
* utilization allows. If the queue is running then a new URB will be
* scheduled to start in the first transfer slot following the end of the
* preceding URB, if that slot has not already expired. If the slot has
* expired (which can happen when IRQ delivery is delayed for a long time),
* the scheduling behavior depends on the URB_ISO_ASAP flag. If the flag
* is clear then the URB will be scheduled to start in the expired slot,
* implying that some of its packets will not be transferred; if the flag
* is set then the URB will be scheduled in the first unexpired slot,
* breaking the queue's synchronization. Upon URB completion, the
* start_frame field will be set to the (micro)frame number in which the
* transfer was scheduled. Ranges for frame counter values are HC-specific
* and can go from as low as 256 to as high as 65536 frames.
*
* Isochronous URBs have a different data transfer model, in part because
* the quality of service is only "best effort". Callers provide specially
* allocated URBs, with number_of_packets worth of iso_frame_desc structures
* at the end. Each such packet is an individual ISO transfer. Isochronous
* URBs are normally queued, submitted by drivers to arrange that
* transfers are at least double buffered, and then explicitly resubmitted
* in completion handlers, so
* that data (such as audio or video) streams at as constant a rate as the
* host controller scheduler can support.
*
* Completion Callbacks:
*
* The completion callback is made in_interrupt(), and one of the first
* things that a completion handler should do is check the status field.
* The status field is provided for all URBs. It is used to report
* unlinked URBs, and status for all non-ISO transfers. It should not
* be examined before the URB is returned to the completion handler.
*
* The context field is normally used to link URBs back to the relevant
* driver or request state.
*
* When the completion callback is invoked for non-isochronous URBs, the
* actual_length field tells how many bytes were transferred. This field
* is updated even when the URB terminated with an error or was unlinked.
*
* ISO transfer status is reported in the status and actual_length fields
* of the iso_frame_desc array, and the number of errors is reported in
* error_count. Completion callbacks for ISO transfers will normally
* (re)submit URBs to ensure a constant transfer rate.
*
* Note that even fields marked "public" should not be touched by the driver
* when the urb is owned by the hcd, that is, since the call to
* usb_submit_urb() till the entry into the completion routine.
*/
struct urb {
/* private: usb core and host controller only fields in the urb */
struct kref kref; /* reference count of the URB */
void *hcpriv; /* private data for host controller */
atomic_t use_count; /* concurrent submissions counter */
atomic_t reject; /* submissions will fail */
int unlinked; /* unlink error code */
/* public: documented fields in the urb that can be used by drivers */
struct list_head urb_list; /* list head for use by the urb's
* current owner */
struct list_head anchor_list; /* the URB may be anchored */
struct usb_anchor *anchor;
struct usb_device *dev; /* (in) pointer to associated device */
struct usb_host_endpoint *ep; /* (internal) pointer to endpoint */
unsigned int pipe; /* (in) pipe information */
unsigned int stream_id; /* (in) stream ID */
int status; /* (return) non-ISO status */
unsigned int transfer_flags; /* (in) URB_SHORT_NOT_OK | ...*/
void *transfer_buffer; /* (in) associated data buffer */
dma_addr_t transfer_dma; /* (in) dma addr for transfer_buffer */
struct scatterlist *sg; /* (in) scatter gather buffer list */
usb: fix number of mapped SG DMA entries Add a new field num_mapped_sgs to struct urb so that we have a place to store the number of mapped entries and can also retain the original value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma() would overwrite this with the number of mapped entries, which would break dma_unmap_sg() because it requires the original number of entries. This fixes warnings like the following when using USB storage devices: ------------[ cut here ]------------ WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695() ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1] Modules linked in: ohci_hcd ehci_hcd Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319 Call Trace: <IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98 [<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43 [<ffffffff811fa5ae>] check_unmap+0x4e4/0x695 [<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf [<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50 [<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117 [<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188 [<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22 [<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0 [<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd] [<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd] [<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd] ... ---[ end trace f29ac88a5a48c580 ]--- Mapped at: [<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139 [<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478 [<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa [<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de [<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161 Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-12-03 22:41:31 +00:00
int num_mapped_sgs; /* (internal) mapped sg entries */
USB: Push scatter gather lists down to host controller drivers. This is the original patch I created before David Vrabel posted a better patch (http://marc.info/?l=linux-usb&m=123377477209109&w=2) that does basically the same thing. This patch will get replaced with his (modified) patch later. Allow USB device drivers that use usb_sg_init() and usb_sg_wait() to push bulk endpoint scatter gather lists down to the host controller drivers. This allows host controller drivers to more efficiently enqueue these transfers, and allows the xHCI host controller to better take advantage of USB 3.0 "bursts" for bulk endpoints. This patch currently only enables scatter gather lists for bulk endpoints. Other endpoint types that use the usb_sg_* functions will not have their scatter gather lists pushed down to the host controller. For periodic endpoints, we want each scatterlist entry to be a separate transfer. Eventually, HCDs could parse these scatter-gather lists for periodic endpoints also. For now, we use the old code and call usb_submit_urb() for each scatterlist entry. The caller of usb_sg_init() can request that all bytes in the scatter gather list be transferred by passing in a length of zero. Handle that request for a bulk endpoint under xHCI by walking the scatter gather list and calculating the length. We could let the HCD handle a zero length in this case, but I'm not sure if the core layers in between will get confused by this. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 02:59:01 +00:00
int num_sgs; /* (in) number of entries in the sg list */
u32 transfer_buffer_length; /* (in) data buffer length */
u32 actual_length; /* (return) actual transfer length */
unsigned char *setup_packet; /* (in) setup packet (control only) */
dma_addr_t setup_dma; /* (in) dma addr for setup_packet */
int start_frame; /* (modify) start frame (ISO) */
int number_of_packets; /* (in) number of ISO packets */
int interval; /* (modify) transfer interval
* (INT/ISO) */
int error_count; /* (return) number of ISO errors */
void *context; /* (in) context for completion */
usb_complete_t complete; /* (in) completion routine */
struct usb_iso_packet_descriptor iso_frame_desc[0];
/* (in) ISO ONLY */
};
/* ----------------------------------------------------------------------- */
/**
* usb_fill_control_urb - initializes a control urb
* @urb: pointer to the urb to initialize.
* @dev: pointer to the struct usb_device for this urb.
* @pipe: the endpoint pipe
* @setup_packet: pointer to the setup_packet buffer
* @transfer_buffer: pointer to the transfer buffer
* @buffer_length: length of the transfer buffer
* @complete_fn: pointer to the usb_complete_t function
* @context: what to set the urb context to.
*
* Initializes a control urb with the proper information needed to submit
* it to a device.
*/
static inline void usb_fill_control_urb(struct urb *urb,
struct usb_device *dev,
unsigned int pipe,
unsigned char *setup_packet,
void *transfer_buffer,
int buffer_length,
usb_complete_t complete_fn,
void *context)
{
urb->dev = dev;
urb->pipe = pipe;
urb->setup_packet = setup_packet;
urb->transfer_buffer = transfer_buffer;
urb->transfer_buffer_length = buffer_length;
urb->complete = complete_fn;
urb->context = context;
}
/**
* usb_fill_bulk_urb - macro to help initialize a bulk urb
* @urb: pointer to the urb to initialize.
* @dev: pointer to the struct usb_device for this urb.
* @pipe: the endpoint pipe
* @transfer_buffer: pointer to the transfer buffer
* @buffer_length: length of the transfer buffer
* @complete_fn: pointer to the usb_complete_t function
* @context: what to set the urb context to.
*
* Initializes a bulk urb with the proper information needed to submit it
* to a device.
*/
static inline void usb_fill_bulk_urb(struct urb *urb,
struct usb_device *dev,
unsigned int pipe,
void *transfer_buffer,
int buffer_length,
usb_complete_t complete_fn,
void *context)
{
urb->dev = dev;
urb->pipe = pipe;
urb->transfer_buffer = transfer_buffer;
urb->transfer_buffer_length = buffer_length;
urb->complete = complete_fn;
urb->context = context;
}
/**
* usb_fill_int_urb - macro to help initialize a interrupt urb
* @urb: pointer to the urb to initialize.
* @dev: pointer to the struct usb_device for this urb.
* @pipe: the endpoint pipe
* @transfer_buffer: pointer to the transfer buffer
* @buffer_length: length of the transfer buffer
* @complete_fn: pointer to the usb_complete_t function
* @context: what to set the urb context to.
* @interval: what to set the urb interval to, encoded like
* the endpoint descriptor's bInterval value.
*
* Initializes a interrupt urb with the proper information needed to submit
* it to a device.
*
* Note that High Speed and SuperSpeed(+) interrupt endpoints use a logarithmic
* encoding of the endpoint interval, and express polling intervals in
* microframes (eight per millisecond) rather than in frames (one per
* millisecond).
*
* Wireless USB also uses the logarithmic encoding, but specifies it in units of
* 128us instead of 125us. For Wireless USB devices, the interval is passed
* through to the host controller, rather than being translated into microframe
* units.
*/
static inline void usb_fill_int_urb(struct urb *urb,
struct usb_device *dev,
unsigned int pipe,
void *transfer_buffer,
int buffer_length,
usb_complete_t complete_fn,
void *context,
int interval)
{
urb->dev = dev;
urb->pipe = pipe;
urb->transfer_buffer = transfer_buffer;
urb->transfer_buffer_length = buffer_length;
urb->complete = complete_fn;
urb->context = context;
if (dev->speed == USB_SPEED_HIGH || dev->speed >= USB_SPEED_SUPER) {
/* make sure interval is within allowed range */
interval = clamp(interval, 1, 16);
urb->interval = 1 << (interval - 1);
} else {
urb->interval = interval;
}
urb->start_frame = -1;
}
extern void usb_init_urb(struct urb *urb);
extern struct urb *usb_alloc_urb(int iso_packets, gfp_t mem_flags);
extern void usb_free_urb(struct urb *urb);
#define usb_put_urb usb_free_urb
extern struct urb *usb_get_urb(struct urb *urb);
extern int usb_submit_urb(struct urb *urb, gfp_t mem_flags);
extern int usb_unlink_urb(struct urb *urb);
extern void usb_kill_urb(struct urb *urb);
extern void usb_poison_urb(struct urb *urb);
extern void usb_unpoison_urb(struct urb *urb);
extern void usb_block_urb(struct urb *urb);
extern void usb_kill_anchored_urbs(struct usb_anchor *anchor);
extern void usb_poison_anchored_urbs(struct usb_anchor *anchor);
extern void usb_unpoison_anchored_urbs(struct usb_anchor *anchor);
extern void usb_unlink_anchored_urbs(struct usb_anchor *anchor);
usb-anchor: Delay usb_wait_anchor_empty_timeout wake up till completion is done usb_wait_anchor_empty_timeout() should wait till the completion handler has run. Both the zd1211rw driver and the uas driver (in its task mgmt) depend on the completion handler having completed when usb_wait_anchor_empty_timeout() returns, as they read state set by the completion handler after an usb_wait_anchor_empty_timeout() call. But __usb_hcd_giveback_urb() calls usb_unanchor_urb before calling the completion handler. This is necessary as the completion handler may re-submit and re-anchor the urb. But this introduces a race where the state these drivers want to read has not been set yet by the completion handler (this race is easily triggered with the uas task mgmt code). I've considered adding an anchor_count to struct urb, which would be incremented on anchor and decremented on unanchor, and then only actually do the anchor / unanchor on 0 -> 1 and 1 -> 0 transtions, combined with moving the unanchor call in hcd_giveback_urb to after calling the completion handler. But this will only work if urb's are only re-anchored to the same anchor as they were anchored to before the completion handler ran. And at least one driver re-anchors to another anchor from the completion handler (rtlwifi). So I have come up with this patch instead, which adds the ability to suspend wakeups of usb_wait_anchor_empty_timeout() waiters to the usb_anchor functionality, and uses this in __usb_hcd_giveback_urb() to delay wake-ups until the completion handler has run. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-09 15:01:41 +00:00
extern void usb_anchor_suspend_wakeups(struct usb_anchor *anchor);
extern void usb_anchor_resume_wakeups(struct usb_anchor *anchor);
extern void usb_anchor_urb(struct urb *urb, struct usb_anchor *anchor);
extern void usb_unanchor_urb(struct urb *urb);
extern int usb_wait_anchor_empty_timeout(struct usb_anchor *anchor,
unsigned int timeout);
extern struct urb *usb_get_from_anchor(struct usb_anchor *anchor);
extern void usb_scuttle_anchored_urbs(struct usb_anchor *anchor);
extern int usb_anchor_empty(struct usb_anchor *anchor);
#define usb_unblock_urb usb_unpoison_urb
/**
* usb_urb_dir_in - check if an URB describes an IN transfer
* @urb: URB to be checked
*
* Return: 1 if @urb describes an IN transfer (device-to-host),
* otherwise 0.
*/
static inline int usb_urb_dir_in(struct urb *urb)
{
return (urb->transfer_flags & URB_DIR_MASK) == URB_DIR_IN;
}
/**
* usb_urb_dir_out - check if an URB describes an OUT transfer
* @urb: URB to be checked
*
* Return: 1 if @urb describes an OUT transfer (host-to-device),
* otherwise 0.
*/
static inline int usb_urb_dir_out(struct urb *urb)
{
return (urb->transfer_flags & URB_DIR_MASK) == URB_DIR_OUT;
}
int usb_urb_ep_type_check(const struct urb *urb);
void *usb_alloc_coherent(struct usb_device *dev, size_t size,
gfp_t mem_flags, dma_addr_t *dma);
void usb_free_coherent(struct usb_device *dev, size_t size,
void *addr, dma_addr_t dma);
#if 0
struct urb *usb_buffer_map(struct urb *urb);
void usb_buffer_dmasync(struct urb *urb);
void usb_buffer_unmap(struct urb *urb);
#endif
struct scatterlist;
int usb_buffer_map_sg(const struct usb_device *dev, int is_in,
struct scatterlist *sg, int nents);
#if 0
void usb_buffer_dmasync_sg(const struct usb_device *dev, int is_in,
struct scatterlist *sg, int n_hw_ents);
#endif
void usb_buffer_unmap_sg(const struct usb_device *dev, int is_in,
struct scatterlist *sg, int n_hw_ents);
/*-------------------------------------------------------------------*
* SYNCHRONOUS CALL SUPPORT *
*-------------------------------------------------------------------*/
extern int usb_control_msg(struct usb_device *dev, unsigned int pipe,
__u8 request, __u8 requesttype, __u16 value, __u16 index,
void *data, __u16 size, int timeout);
extern int usb_interrupt_msg(struct usb_device *usb_dev, unsigned int pipe,
void *data, int len, int *actual_length, int timeout);
extern int usb_bulk_msg(struct usb_device *usb_dev, unsigned int pipe,
void *data, int len, int *actual_length,
int timeout);
/* wrappers around usb_control_msg() for the most common standard requests */
extern int usb_get_descriptor(struct usb_device *dev, unsigned char desctype,
unsigned char descindex, void *buf, int size);
extern int usb_get_status(struct usb_device *dev,
int recip, int type, int target, void *data);
static inline int usb_get_std_status(struct usb_device *dev,
int recip, int target, void *data)
{
return usb_get_status(dev, recip, USB_STATUS_TYPE_STANDARD, target,
data);
}
static inline int usb_get_ptm_status(struct usb_device *dev, void *data)
{
return usb_get_status(dev, USB_RECIP_DEVICE, USB_STATUS_TYPE_PTM,
0, data);
}
extern int usb_string(struct usb_device *dev, int index,
char *buf, size_t size);
/* wrappers that also update important state inside usbcore */
extern int usb_clear_halt(struct usb_device *dev, int pipe);
extern int usb_reset_configuration(struct usb_device *dev);
extern int usb_set_interface(struct usb_device *dev, int ifnum, int alternate);
extern void usb_reset_endpoint(struct usb_device *dev, unsigned int epaddr);
/* this request isn't really synchronous, but it belongs with the others */
extern int usb_driver_set_configuration(struct usb_device *udev, int config);
/* choose and set configuration for device */
extern int usb_choose_configuration(struct usb_device *udev);
extern int usb_set_configuration(struct usb_device *dev, int configuration);
/*
* timeouts, in milliseconds, used for sending/receiving control messages
* they typically complete within a few frames (msec) after they're issued
* USB identifies 5 second timeouts, maybe more in a few cases, and a few
* slow devices (like some MGE Ellipse UPSes) actually push that limit.
*/
#define USB_CTRL_GET_TIMEOUT 5000
#define USB_CTRL_SET_TIMEOUT 5000
/**
* struct usb_sg_request - support for scatter/gather I/O
* @status: zero indicates success, else negative errno
* @bytes: counts bytes transferred.
*
* These requests are initialized using usb_sg_init(), and then are used
* as request handles passed to usb_sg_wait() or usb_sg_cancel(). Most
* members of the request object aren't for driver access.
*
* The status and bytecount values are valid only after usb_sg_wait()
* returns. If the status is zero, then the bytecount matches the total
* from the request.
*
* After an error completion, drivers may need to clear a halt condition
* on the endpoint.
*/
struct usb_sg_request {
int status;
size_t bytes;
/* private:
* members below are private to usbcore,
* and are not provided for driver access!
*/
spinlock_t lock;
struct usb_device *dev;
int pipe;
int entries;
struct urb **urbs;
int count;
struct completion complete;
};
int usb_sg_init(
struct usb_sg_request *io,
struct usb_device *dev,
unsigned pipe,
unsigned period,
struct scatterlist *sg,
int nents,
size_t length,
gfp_t mem_flags
);
void usb_sg_cancel(struct usb_sg_request *io);
void usb_sg_wait(struct usb_sg_request *io);
/* ----------------------------------------------------------------------- */
/*
* For various legacy reasons, Linux has a small cookie that's paired with
* a struct usb_device to identify an endpoint queue. Queue characteristics
* are defined by the endpoint's descriptor. This cookie is called a "pipe",
* an unsigned int encoded as:
*
* - direction: bit 7 (0 = Host-to-Device [Out],
* 1 = Device-to-Host [In] ...
* like endpoint bEndpointAddress)
* - device address: bits 8-14 ... bit positions known to uhci-hcd
* - endpoint: bits 15-18 ... bit positions known to uhci-hcd
* - pipe type: bits 30-31 (00 = isochronous, 01 = interrupt,
* 10 = control, 11 = bulk)
*
* Given the device address and endpoint descriptor, pipes are redundant.
*/
/* NOTE: these are not the standard USB_ENDPOINT_XFER_* values!! */
/* (yet ... they're the values used by usbfs) */
#define PIPE_ISOCHRONOUS 0
#define PIPE_INTERRUPT 1
#define PIPE_CONTROL 2
#define PIPE_BULK 3
#define usb_pipein(pipe) ((pipe) & USB_DIR_IN)
#define usb_pipeout(pipe) (!usb_pipein(pipe))
#define usb_pipedevice(pipe) (((pipe) >> 8) & 0x7f)
#define usb_pipeendpoint(pipe) (((pipe) >> 15) & 0xf)
#define usb_pipetype(pipe) (((pipe) >> 30) & 3)
#define usb_pipeisoc(pipe) (usb_pipetype((pipe)) == PIPE_ISOCHRONOUS)
#define usb_pipeint(pipe) (usb_pipetype((pipe)) == PIPE_INTERRUPT)
#define usb_pipecontrol(pipe) (usb_pipetype((pipe)) == PIPE_CONTROL)
#define usb_pipebulk(pipe) (usb_pipetype((pipe)) == PIPE_BULK)
static inline unsigned int __create_pipe(struct usb_device *dev,
unsigned int endpoint)
{
return (dev->devnum << 8) | (endpoint << 15);
}
/* Create various pipes... */
#define usb_sndctrlpipe(dev, endpoint) \
((PIPE_CONTROL << 30) | __create_pipe(dev, endpoint))
#define usb_rcvctrlpipe(dev, endpoint) \
((PIPE_CONTROL << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
#define usb_sndisocpipe(dev, endpoint) \
((PIPE_ISOCHRONOUS << 30) | __create_pipe(dev, endpoint))
#define usb_rcvisocpipe(dev, endpoint) \
((PIPE_ISOCHRONOUS << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
#define usb_sndbulkpipe(dev, endpoint) \
((PIPE_BULK << 30) | __create_pipe(dev, endpoint))
#define usb_rcvbulkpipe(dev, endpoint) \
((PIPE_BULK << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
#define usb_sndintpipe(dev, endpoint) \
((PIPE_INTERRUPT << 30) | __create_pipe(dev, endpoint))
#define usb_rcvintpipe(dev, endpoint) \
((PIPE_INTERRUPT << 30) | __create_pipe(dev, endpoint) | USB_DIR_IN)
static inline struct usb_host_endpoint *
usb_pipe_endpoint(struct usb_device *dev, unsigned int pipe)
{
struct usb_host_endpoint **eps;
eps = usb_pipein(pipe) ? dev->ep_in : dev->ep_out;
return eps[usb_pipeendpoint(pipe)];
}
/*-------------------------------------------------------------------------*/
static inline __u16
usb_maxpacket(struct usb_device *udev, int pipe, int is_out)
{
struct usb_host_endpoint *ep;
unsigned epnum = usb_pipeendpoint(pipe);
if (is_out) {
WARN_ON(usb_pipein(pipe));
ep = udev->ep_out[epnum];
} else {
WARN_ON(usb_pipeout(pipe));
ep = udev->ep_in[epnum];
}
if (!ep)
return 0;
/* NOTE: only 0x07ff bits are for packet size... */
USB: use usb_endpoint_maxp() instead of le16_to_cpu() Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size instead of le16_to_cpu(desc->wMaxPacketSize). This patch fix it up Cc: Armin Fuerst <fuerst@in.tum.de> Cc: Pavel Machek <pavel@ucw.cz> Cc: Johannes Erdfelt <johannes@erdfelt.com> Cc: Vojtech Pavlik <vojtech@suse.cz> Cc: Oliver Neukum <oliver@neukum.name> Cc: David Kubicek <dave@awk.cz> Cc: Johan Hovold <jhovold@gmail.com> Cc: Brad Hards <bhards@bigpond.net.au> Acked-by: Felipe Balbi <balbi@ti.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de> Cc: David Brownell <david-b@pacbell.net> Cc: David Lopo <dlopo@chipidea.mips.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Xie Xiaobo <X.Xie@freescale.com> Cc: Li Yang <leoli@freescale.com> Cc: Jiang Bo <tanya.jiang@freescale.com> Cc: Yuan-hsin Chen <yhchen@faraday-tech.com> Cc: Darius Augulis <augulis.darius@gmail.com> Cc: Xiaochen Shen <xiaochen.shen@intel.com> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Ben Dooks <ben@simtec.co.uk> Cc: Thomas Abraham <thomas.ab@samsung.com> Cc: Herbert Pötzl <herbert@13thfloor.at> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Roman Weissgaerber <weissg@vienna.at> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: Florian Floe Echtler <echtler@fs.tum.de> Cc: Christian Lucht <lucht@codemercs.com> Cc: Juergen Stuber <starblue@sourceforge.net> Cc: Georges Toth <g.toth@e-biz.lu> Cc: Bill Ryder <bryder@sgi.com> Cc: Kuba Ober <kuba@mareimbrium.org> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-23 10:12:03 +00:00
return usb_endpoint_maxp(&ep->desc);
}
/* ----------------------------------------------------------------------- */
/* translate USB error codes to codes user space understands */
static inline int usb_translate_errors(int error_code)
{
switch (error_code) {
case 0:
case -ENOMEM:
case -ENODEV:
case -EOPNOTSUPP:
return error_code;
default:
return -EIO;
}
}
/* Events from the usb core */
#define USB_DEVICE_ADD 0x0001
#define USB_DEVICE_REMOVE 0x0002
#define USB_BUS_ADD 0x0003
#define USB_BUS_REMOVE 0x0004
extern void usb_register_notify(struct notifier_block *nb);
extern void usb_unregister_notify(struct notifier_block *nb);
/* debugfs stuff */
extern struct dentry *usb_debug_root;
/* LED triggers */
enum usb_led_event {
USB_LED_EVENT_HOST = 0,
USB_LED_EVENT_GADGET = 1,
};
#ifdef CONFIG_USB_LED_TRIG
extern void usb_led_activity(enum usb_led_event ev);
#else
static inline void usb_led_activity(enum usb_led_event ev) {}
#endif
#endif /* __KERNEL__ */
#endif