linux-stable/drivers/regulator/bd9571mwv-regulator.c

368 lines
9.2 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
/*
* ROHM BD9571MWV-M and BD9574MWF-M regulator driver
*
* Copyright (C) 2017 Marek Vasut <marek.vasut+renesas@gmail.com>
*
* Based on the TPS65086 driver
*
* NOTE: VD09 is missing
*/
#include <linux/mfd/rohm-generic.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
#include <linux/mfd/bd9571mwv.h>
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
struct bd9571mwv_reg {
struct regmap *regmap;
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
/* DDR Backup Power */
u8 bkup_mode_cnt_keepon; /* from "rohm,ddr-backup-power" */
u8 bkup_mode_cnt_saved;
bool bkup_mode_enabled;
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
/* Power switch type */
bool rstbmode_level;
bool rstbmode_pulse;
};
enum bd9571mwv_regulators { VD09, VD18, VD25, VD33, DVFS };
#define BD9571MWV_REG(_name, _of, _id, _ops, _vr, _vm, _nv, _min, _step, _lmin)\
{ \
.name = _name, \
.of_match = of_match_ptr(_of), \
.regulators_node = "regulators", \
.id = _id, \
.ops = &_ops, \
.n_voltages = _nv, \
.type = REGULATOR_VOLTAGE, \
.owner = THIS_MODULE, \
.vsel_reg = _vr, \
.vsel_mask = _vm, \
.min_uV = _min, \
.uV_step = _step, \
.linear_min_sel = _lmin, \
}
static int bd9571mwv_avs_get_moni_state(struct regulator_dev *rdev)
{
unsigned int val;
int ret;
ret = regmap_read(rdev->regmap, BD9571MWV_AVS_SET_MONI, &val);
if (ret != 0)
return ret;
return val & BD9571MWV_AVS_SET_MONI_MASK;
}
static int bd9571mwv_avs_set_voltage_sel_regmap(struct regulator_dev *rdev,
unsigned int sel)
{
int ret;
ret = bd9571mwv_avs_get_moni_state(rdev);
if (ret < 0)
return ret;
return regmap_write_bits(rdev->regmap, BD9571MWV_AVS_VD09_VID(ret),
rdev->desc->vsel_mask, sel);
}
static int bd9571mwv_avs_get_voltage_sel_regmap(struct regulator_dev *rdev)
{
unsigned int val;
int ret;
ret = bd9571mwv_avs_get_moni_state(rdev);
if (ret < 0)
return ret;
ret = regmap_read(rdev->regmap, BD9571MWV_AVS_VD09_VID(ret), &val);
if (ret != 0)
return ret;
val &= rdev->desc->vsel_mask;
val >>= ffs(rdev->desc->vsel_mask) - 1;
return val;
}
static int bd9571mwv_reg_set_voltage_sel_regmap(struct regulator_dev *rdev,
unsigned int sel)
{
return regmap_write_bits(rdev->regmap, BD9571MWV_DVFS_SETVID,
rdev->desc->vsel_mask, sel);
}
/* Operations permitted on AVS voltage regulator */
static const struct regulator_ops avs_ops = {
.set_voltage_sel = bd9571mwv_avs_set_voltage_sel_regmap,
.map_voltage = regulator_map_voltage_linear,
.get_voltage_sel = bd9571mwv_avs_get_voltage_sel_regmap,
.list_voltage = regulator_list_voltage_linear,
};
/* Operations permitted on voltage regulators */
static const struct regulator_ops reg_ops = {
.set_voltage_sel = bd9571mwv_reg_set_voltage_sel_regmap,
.map_voltage = regulator_map_voltage_linear,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.list_voltage = regulator_list_voltage_linear,
};
/* Operations permitted on voltage monitors */
static const struct regulator_ops vid_ops = {
.map_voltage = regulator_map_voltage_linear,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.list_voltage = regulator_list_voltage_linear,
};
static const struct regulator_desc regulators[] = {
BD9571MWV_REG("VD09", "vd09", VD09, avs_ops, 0, 0x7f,
0x6f, 600000, 10000, 0x3c),
BD9571MWV_REG("VD18", "vd18", VD18, vid_ops, BD9571MWV_VD18_VID, 0xf,
16, 1625000, 25000, 0),
BD9571MWV_REG("VD25", "vd25", VD25, vid_ops, BD9571MWV_VD25_VID, 0xf,
16, 2150000, 50000, 0),
BD9571MWV_REG("VD33", "vd33", VD33, vid_ops, BD9571MWV_VD33_VID, 0xf,
11, 2800000, 100000, 0),
BD9571MWV_REG("DVFS", "dvfs", DVFS, reg_ops,
BD9571MWV_DVFS_MONIVDAC, 0x7f,
0x6f, 600000, 10000, 0x3c),
};
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
#ifdef CONFIG_PM_SLEEP
static int bd9571mwv_bkup_mode_read(struct bd9571mwv_reg *bdreg,
unsigned int *mode)
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
{
int ret;
ret = regmap_read(bdreg->regmap, BD9571MWV_BKUP_MODE_CNT, mode);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
if (ret) {
dev_err(regmap_get_device(bdreg->regmap),
"failed to read backup mode (%d)\n", ret);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
return ret;
}
return 0;
}
static int bd9571mwv_bkup_mode_write(struct bd9571mwv_reg *bdreg,
unsigned int mode)
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
{
int ret;
ret = regmap_write(bdreg->regmap, BD9571MWV_BKUP_MODE_CNT, mode);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
if (ret) {
dev_err(regmap_get_device(bdreg->regmap),
"failed to configure backup mode 0x%x (%d)\n",
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
mode, ret);
return ret;
}
return 0;
}
static ssize_t backup_mode_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct bd9571mwv_reg *bdreg = dev_get_drvdata(dev);
return sysfs_emit(buf, "%s\n", bdreg->bkup_mode_enabled ? "on" : "off");
}
static ssize_t backup_mode_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct bd9571mwv_reg *bdreg = dev_get_drvdata(dev);
unsigned int mode;
int ret;
if (!count)
return 0;
ret = kstrtobool(buf, &bdreg->bkup_mode_enabled);
if (ret)
return ret;
if (!bdreg->rstbmode_level)
return count;
/*
* Configure DDR Backup Mode, to change the role of the accessory power
* switch from a power switch to a wake-up switch, or vice versa
*/
ret = bd9571mwv_bkup_mode_read(bdreg, &mode);
if (ret)
return ret;
mode &= ~BD9571MWV_BKUP_MODE_CNT_KEEPON_MASK;
if (bdreg->bkup_mode_enabled)
mode |= bdreg->bkup_mode_cnt_keepon;
ret = bd9571mwv_bkup_mode_write(bdreg, mode);
if (ret)
return ret;
return count;
}
static DEVICE_ATTR_RW(backup_mode);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
static int bd9571mwv_suspend(struct device *dev)
{
struct bd9571mwv_reg *bdreg = dev_get_drvdata(dev);
unsigned int mode;
int ret;
if (!bdreg->bkup_mode_enabled)
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
return 0;
/* Save DDR Backup Mode */
ret = bd9571mwv_bkup_mode_read(bdreg, &mode);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
if (ret)
return ret;
bdreg->bkup_mode_cnt_saved = mode;
if (!bdreg->rstbmode_pulse)
return 0;
/* Enable DDR Backup Mode */
mode &= ~BD9571MWV_BKUP_MODE_CNT_KEEPON_MASK;
mode |= bdreg->bkup_mode_cnt_keepon;
if (mode != bdreg->bkup_mode_cnt_saved)
return bd9571mwv_bkup_mode_write(bdreg, mode);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
return 0;
}
static int bd9571mwv_resume(struct device *dev)
{
struct bd9571mwv_reg *bdreg = dev_get_drvdata(dev);
if (!bdreg->bkup_mode_enabled)
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
return 0;
/* Restore DDR Backup Mode */
return bd9571mwv_bkup_mode_write(bdreg, bdreg->bkup_mode_cnt_saved);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
}
static const struct dev_pm_ops bd9571mwv_pm = {
SET_SYSTEM_SLEEP_PM_OPS(bd9571mwv_suspend, bd9571mwv_resume)
};
static int bd9571mwv_regulator_remove(struct platform_device *pdev)
{
device_remove_file(&pdev->dev, &dev_attr_backup_mode);
return 0;
}
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
#define DEV_PM_OPS &bd9571mwv_pm
#else
#define DEV_PM_OPS NULL
#define bd9571mwv_regulator_remove NULL
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
#endif /* CONFIG_PM_SLEEP */
static int bd9571mwv_regulator_probe(struct platform_device *pdev)
{
struct regulator_config config = { };
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
struct bd9571mwv_reg *bdreg;
struct regulator_dev *rdev;
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
unsigned int val;
int i;
enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
bdreg = devm_kzalloc(&pdev->dev, sizeof(*bdreg), GFP_KERNEL);
if (!bdreg)
return -ENOMEM;
bdreg->regmap = dev_get_regmap(pdev->dev.parent, NULL);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
platform_set_drvdata(pdev, bdreg);
config.dev = &pdev->dev;
config.dev->of_node = pdev->dev.parent->of_node;
config.driver_data = bdreg;
config.regmap = bdreg->regmap;
for (i = 0; i < ARRAY_SIZE(regulators); i++) {
/* BD9574MWF supports DVFS only */
if (chip == ROHM_CHIP_TYPE_BD9574 && regulators[i].id != DVFS)
continue;
rdev = devm_regulator_register(&pdev->dev, &regulators[i],
&config);
if (IS_ERR(rdev)) {
dev_err(&pdev->dev, "failed to register %s regulator\n",
regulators[i].name);
return PTR_ERR(rdev);
}
}
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
val = 0;
of_property_read_u32(config.dev->of_node, "rohm,ddr-backup-power", &val);
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
if (val & ~BD9571MWV_BKUP_MODE_CNT_KEEPON_MASK) {
dev_err(&pdev->dev, "invalid %s mode %u\n",
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
"rohm,ddr-backup-power", val);
return -EINVAL;
}
bdreg->bkup_mode_cnt_keepon = val;
bdreg->rstbmode_level = of_property_read_bool(config.dev->of_node,
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
"rohm,rstbmode-level");
bdreg->rstbmode_pulse = of_property_read_bool(config.dev->of_node,
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
"rohm,rstbmode-pulse");
if (bdreg->rstbmode_level && bdreg->rstbmode_pulse) {
dev_err(&pdev->dev, "only one rohm,rstbmode-* may be specified");
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
return -EINVAL;
}
#ifdef CONFIG_PM_SLEEP
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
if (bdreg->bkup_mode_cnt_keepon) {
int ret;
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
/*
* Backup mode is enabled by default in pulse mode, but needs
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
* explicit user setup in level mode.
*/
bdreg->bkup_mode_enabled = bdreg->rstbmode_pulse;
ret = device_create_file(&pdev->dev, &dev_attr_backup_mode);
if (ret)
return ret;
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
}
#endif /* CONFIG_PM_SLEEP */
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
return 0;
}
static const struct platform_device_id bd9571mwv_regulator_id_table[] = {
{ "bd9571mwv-regulator", ROHM_CHIP_TYPE_BD9571 },
{ "bd9574mwf-regulator", ROHM_CHIP_TYPE_BD9574 },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(platform, bd9571mwv_regulator_id_table);
static struct platform_driver bd9571mwv_regulator_driver = {
.driver = {
.name = "bd9571mwv-regulator",
regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14 Probing of regulators can be a slow operation and can contribute to slower boot times. This is especially true if a regulator is turned on at probe time (with regulator-boot-on or regulator-always-on) and the regulator requires delays (off-on-time, ramp time, etc). While the overall kernel is not ready to switch to async probe by default, as per the discussion on the mailing lists [1] it is believed that the regulator subsystem is in good shape and we can move regulator drivers over wholesale. There is no way to just magically opt in all regulators (regulators are just normal drivers like platform_driver), so we set PROBE_PREFER_ASYNCHRONOUS for all regulators found in 'drivers/regulator' individually. Given the number of drivers touched and the impossibility to test this ahead of time, it wouldn't be shocking at all if this caused a regression for someone. If there is a regression caused by this patch, it's likely to be one of the cases talked about in [1]. As a "quick fix", drivers involved in the regression could be fixed by changing them to PROBE_FORCE_SYNCHRONOUS. That being said, the correct fix would be to directly fix the problem that caused the issue with async probe. The approach here follows a similar approach that was used for the mmc subsystem several years ago [2]. In fact, I ran nearly the same python script to auto-generate the changes. The only thing I changed was to search for "i2c_driver", "spmi_driver", and "spi_driver" in addition to "platform_driver". [1] https://lore.kernel.org/r/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk [2] https://lore.kernel.org/r/20200903232441.2694866-1-dianders@chromium.org/ Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20230316125351.1.I2a4677392a38db5758dee0788b2cea5872562a82@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2023-03-16 19:54:38 +00:00
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
regulator: bd9571mwv: Add support for backup mode The BD9571MWV PMIC supports backup mode, which keeps one or more DDR rails powered while the main SoC is powered down. Which DDR rails are to be kept powered is board-specific, and controlled using the optional "rohm,ddr-backup-power" DT property. In the absence of this property, backup mode is not available. Backup mode can be enabled or disabled by the user using the standard "wakeup" virtual file in sysfs, e.g. to enable: echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup When the PMIC is configured for backup mode, the role of the accessory power switch changes from a power switch to a wake-up switch. Two types of switches (or signals) can be used: A. With a momentary power switch (or pulse signal), the PMIC is configured for backup mode in the PMIC driver's suspend callback, during system suspend. Backup mode is enabled by default, as there is no further impact during normal system operation. B. With a toggle power switch (or level signal), the following steps must be followed exactly: 1. Configure PMIC for backup mode, 2. Switch accessory power switch off, to prepare for system suspend, which is a manual step not controlled by software, 3. Suspend system. This mode is not yet supported by the driver. As the switch type is board-specific, and cannot be determined automatically, it is obtained from the presence of one of the "rohm,rstbmode-*" properties in DT. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-18 13:18:04 +00:00
.pm = DEV_PM_OPS,
},
.probe = bd9571mwv_regulator_probe,
.remove = bd9571mwv_regulator_remove,
.id_table = bd9571mwv_regulator_id_table,
};
module_platform_driver(bd9571mwv_regulator_driver);
MODULE_AUTHOR("Marek Vasut <marek.vasut+renesas@gmail.com>");
MODULE_DESCRIPTION("BD9571MWV Regulator driver");
MODULE_LICENSE("GPL v2");