usb: Add driver to allow any GPIO to be used for 7211 USB signals
The Broadcom 7211 has new functionality that allows some USB low
speed side band signals, that go from the XHCI host controller to
pins on the chip, to be remapped to use any GPIO pin instead of the
limited set selectable by hardware. This can be done without changing
the standard driver for the host controller. There is currently
support for three USB signals, PWRON, VBUS_PRESENT and PWRFLT. This
driver will allow the remapping of any of these three signals based
on settings in the Device Tree node for the driver. The driver was
written so that it could handle additional signals added in the
future by just adding the correct properties to the DT node.
Below is an example of a DT node that would remap all three
signals:
usb_pinmap: usb-pinmap@22000d0 {
compatible = "brcm,usb-pinmap";
reg = <0x22000d0 0x4>;
in-gpios = <&gpio 18 0>, <&gpio 19 0>;
brcm,in-functions = "VBUS", "PWRFLT";
brcm,in-masks = <0x8000 0x40000 0x10000 0x80000>;
out-gpios = <&gpio 20 0>;
brcm,out-functions = "PWRON";
brcm,out-masks = <0x20000 0x800000 0x400000 0x200000>;
interrupts = <0x0 0xb2 0x4>;
};
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20201012200007.8862-3-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-12 20:00:07 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0
|
|
|
|
/* Copyright (c) 2020, Broadcom */
|
|
|
|
|
|
|
|
#include <linux/init.h>
|
|
|
|
#include <linux/types.h>
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/platform_device.h>
|
|
|
|
#include <linux/interrupt.h>
|
|
|
|
#include <linux/io.h>
|
|
|
|
#include <linux/device.h>
|
|
|
|
#include <linux/of.h>
|
|
|
|
#include <linux/kernel.h>
|
|
|
|
#include <linux/kdebug.h>
|
|
|
|
#include <linux/gpio/consumer.h>
|
|
|
|
|
|
|
|
struct out_pin {
|
|
|
|
u32 enable_mask;
|
|
|
|
u32 value_mask;
|
|
|
|
u32 changed_mask;
|
|
|
|
u32 clr_changed_mask;
|
|
|
|
struct gpio_desc *gpiod;
|
|
|
|
const char *name;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct in_pin {
|
|
|
|
u32 enable_mask;
|
|
|
|
u32 value_mask;
|
|
|
|
struct gpio_desc *gpiod;
|
|
|
|
const char *name;
|
|
|
|
struct brcmstb_usb_pinmap_data *pdata;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct brcmstb_usb_pinmap_data {
|
|
|
|
void __iomem *regs;
|
|
|
|
int in_count;
|
|
|
|
struct in_pin *in_pins;
|
|
|
|
int out_count;
|
|
|
|
struct out_pin *out_pins;
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
|
|
static void pinmap_set(void __iomem *reg, u32 mask)
|
|
|
|
{
|
|
|
|
u32 val;
|
|
|
|
|
|
|
|
val = readl(reg);
|
|
|
|
val |= mask;
|
|
|
|
writel(val, reg);
|
|
|
|
}
|
|
|
|
|
|
|
|
static void pinmap_unset(void __iomem *reg, u32 mask)
|
|
|
|
{
|
|
|
|
u32 val;
|
|
|
|
|
|
|
|
val = readl(reg);
|
|
|
|
val &= ~mask;
|
|
|
|
writel(val, reg);
|
|
|
|
}
|
|
|
|
|
|
|
|
static void sync_in_pin(struct in_pin *pin)
|
|
|
|
{
|
|
|
|
u32 val;
|
|
|
|
|
|
|
|
val = gpiod_get_value(pin->gpiod);
|
|
|
|
if (val)
|
|
|
|
pinmap_set(pin->pdata->regs, pin->value_mask);
|
|
|
|
else
|
|
|
|
pinmap_unset(pin->pdata->regs, pin->value_mask);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Interrupt from override register, propagate from override bit
|
|
|
|
* to GPIO.
|
|
|
|
*/
|
|
|
|
static irqreturn_t brcmstb_usb_pinmap_ovr_isr(int irq, void *dev_id)
|
|
|
|
{
|
|
|
|
struct brcmstb_usb_pinmap_data *pdata = dev_id;
|
|
|
|
struct out_pin *pout;
|
|
|
|
u32 val;
|
|
|
|
u32 bit;
|
|
|
|
int x;
|
|
|
|
|
|
|
|
pr_debug("%s: reg: 0x%x\n", __func__, readl(pdata->regs));
|
|
|
|
pout = pdata->out_pins;
|
|
|
|
for (x = 0; x < pdata->out_count; x++) {
|
|
|
|
val = readl(pdata->regs);
|
|
|
|
if (val & pout->changed_mask) {
|
|
|
|
pinmap_set(pdata->regs, pout->clr_changed_mask);
|
|
|
|
pinmap_unset(pdata->regs, pout->clr_changed_mask);
|
|
|
|
bit = val & pout->value_mask;
|
|
|
|
gpiod_set_value(pout->gpiod, bit ? 1 : 0);
|
|
|
|
pr_debug("%s: %s bit changed state to %d\n",
|
|
|
|
__func__, pout->name, bit ? 1 : 0);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Interrupt from GPIO, propagate from GPIO to override bit.
|
|
|
|
*/
|
|
|
|
static irqreturn_t brcmstb_usb_pinmap_gpio_isr(int irq, void *dev_id)
|
|
|
|
{
|
|
|
|
struct in_pin *pin = dev_id;
|
|
|
|
|
|
|
|
pr_debug("%s: %s pin changed state\n", __func__, pin->name);
|
|
|
|
sync_in_pin(pin);
|
|
|
|
return IRQ_HANDLED;
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
static void get_pin_counts(struct device_node *dn, int *in_count,
|
|
|
|
int *out_count)
|
|
|
|
{
|
|
|
|
int in;
|
|
|
|
int out;
|
|
|
|
|
|
|
|
*in_count = 0;
|
|
|
|
*out_count = 0;
|
|
|
|
in = of_property_count_strings(dn, "brcm,in-functions");
|
|
|
|
if (in < 0)
|
|
|
|
return;
|
|
|
|
out = of_property_count_strings(dn, "brcm,out-functions");
|
|
|
|
if (out < 0)
|
|
|
|
return;
|
|
|
|
*in_count = in;
|
|
|
|
*out_count = out;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int parse_pins(struct device *dev, struct device_node *dn,
|
|
|
|
struct brcmstb_usb_pinmap_data *pdata)
|
|
|
|
{
|
|
|
|
struct out_pin *pout;
|
|
|
|
struct in_pin *pin;
|
|
|
|
int index;
|
|
|
|
int res;
|
|
|
|
int x;
|
|
|
|
|
|
|
|
pin = pdata->in_pins;
|
|
|
|
for (x = 0, index = 0; x < pdata->in_count; x++) {
|
|
|
|
pin->gpiod = devm_gpiod_get_index(dev, "in", x, GPIOD_IN);
|
|
|
|
if (IS_ERR(pin->gpiod)) {
|
|
|
|
dev_err(dev, "Error getting gpio %s\n", pin->name);
|
|
|
|
return PTR_ERR(pin->gpiod);
|
|
|
|
|
|
|
|
}
|
|
|
|
res = of_property_read_string_index(dn, "brcm,in-functions", x,
|
|
|
|
&pin->name);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting brcm,in-functions for %s\n",
|
|
|
|
pin->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
res = of_property_read_u32_index(dn, "brcm,in-masks", index++,
|
|
|
|
&pin->enable_mask);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting 1st brcm,in-masks for %s\n",
|
|
|
|
pin->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
res = of_property_read_u32_index(dn, "brcm,in-masks", index++,
|
|
|
|
&pin->value_mask);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting 2nd brcm,in-masks for %s\n",
|
|
|
|
pin->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
pin->pdata = pdata;
|
|
|
|
pin++;
|
|
|
|
}
|
|
|
|
pout = pdata->out_pins;
|
|
|
|
for (x = 0, index = 0; x < pdata->out_count; x++) {
|
|
|
|
pout->gpiod = devm_gpiod_get_index(dev, "out", x,
|
|
|
|
GPIOD_OUT_HIGH);
|
|
|
|
if (IS_ERR(pout->gpiod)) {
|
|
|
|
dev_err(dev, "Error getting gpio %s\n", pin->name);
|
|
|
|
return PTR_ERR(pout->gpiod);
|
|
|
|
}
|
|
|
|
res = of_property_read_string_index(dn, "brcm,out-functions", x,
|
|
|
|
&pout->name);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting brcm,out-functions for %s\n",
|
|
|
|
pout->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
res = of_property_read_u32_index(dn, "brcm,out-masks", index++,
|
|
|
|
&pout->enable_mask);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting 1st brcm,out-masks for %s\n",
|
|
|
|
pout->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
res = of_property_read_u32_index(dn, "brcm,out-masks", index++,
|
|
|
|
&pout->value_mask);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting 2nd brcm,out-masks for %s\n",
|
|
|
|
pout->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
res = of_property_read_u32_index(dn, "brcm,out-masks", index++,
|
|
|
|
&pout->changed_mask);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting 3rd brcm,out-masks for %s\n",
|
|
|
|
pout->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
res = of_property_read_u32_index(dn, "brcm,out-masks", index++,
|
|
|
|
&pout->clr_changed_mask);
|
|
|
|
if (res < 0) {
|
|
|
|
dev_err(dev, "Error getting 4th out-masks for %s\n",
|
|
|
|
pout->name);
|
|
|
|
return res;
|
|
|
|
}
|
|
|
|
pout++;
|
|
|
|
}
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
2020-10-30 09:28:17 +00:00
|
|
|
static void sync_all_pins(struct brcmstb_usb_pinmap_data *pdata)
|
usb: Add driver to allow any GPIO to be used for 7211 USB signals
The Broadcom 7211 has new functionality that allows some USB low
speed side band signals, that go from the XHCI host controller to
pins on the chip, to be remapped to use any GPIO pin instead of the
limited set selectable by hardware. This can be done without changing
the standard driver for the host controller. There is currently
support for three USB signals, PWRON, VBUS_PRESENT and PWRFLT. This
driver will allow the remapping of any of these three signals based
on settings in the Device Tree node for the driver. The driver was
written so that it could handle additional signals added in the
future by just adding the correct properties to the DT node.
Below is an example of a DT node that would remap all three
signals:
usb_pinmap: usb-pinmap@22000d0 {
compatible = "brcm,usb-pinmap";
reg = <0x22000d0 0x4>;
in-gpios = <&gpio 18 0>, <&gpio 19 0>;
brcm,in-functions = "VBUS", "PWRFLT";
brcm,in-masks = <0x8000 0x40000 0x10000 0x80000>;
out-gpios = <&gpio 20 0>;
brcm,out-functions = "PWRON";
brcm,out-masks = <0x20000 0x800000 0x400000 0x200000>;
interrupts = <0x0 0xb2 0x4>;
};
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20201012200007.8862-3-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-12 20:00:07 +00:00
|
|
|
{
|
|
|
|
struct out_pin *pout;
|
|
|
|
struct in_pin *pin;
|
|
|
|
int val;
|
|
|
|
int x;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Enable the override, clear any changed condition and
|
|
|
|
* propagate the state to the GPIO for all out pins.
|
|
|
|
*/
|
|
|
|
pout = pdata->out_pins;
|
|
|
|
for (x = 0; x < pdata->out_count; x++) {
|
|
|
|
pinmap_set(pdata->regs, pout->enable_mask);
|
|
|
|
pinmap_set(pdata->regs, pout->clr_changed_mask);
|
|
|
|
pinmap_unset(pdata->regs, pout->clr_changed_mask);
|
|
|
|
val = readl(pdata->regs) & pout->value_mask;
|
|
|
|
gpiod_set_value(pout->gpiod, val ? 1 : 0);
|
|
|
|
pout++;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* sync and enable all in pins. */
|
|
|
|
pin = pdata->in_pins;
|
|
|
|
for (x = 0; x < pdata->in_count; x++) {
|
|
|
|
sync_in_pin(pin);
|
|
|
|
pinmap_set(pdata->regs, pin->enable_mask);
|
|
|
|
pin++;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
static int __init brcmstb_usb_pinmap_probe(struct platform_device *pdev)
|
|
|
|
{
|
|
|
|
struct device_node *dn = pdev->dev.of_node;
|
|
|
|
struct brcmstb_usb_pinmap_data *pdata;
|
|
|
|
struct in_pin *pin;
|
|
|
|
struct resource *r;
|
|
|
|
int out_count;
|
|
|
|
int in_count;
|
|
|
|
int err;
|
|
|
|
int irq;
|
|
|
|
int x;
|
|
|
|
|
|
|
|
get_pin_counts(dn, &in_count, &out_count);
|
|
|
|
if ((in_count + out_count) == 0)
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
2021-06-05 08:09:14 +00:00
|
|
|
if (!r)
|
|
|
|
return -EINVAL;
|
usb: Add driver to allow any GPIO to be used for 7211 USB signals
The Broadcom 7211 has new functionality that allows some USB low
speed side band signals, that go from the XHCI host controller to
pins on the chip, to be remapped to use any GPIO pin instead of the
limited set selectable by hardware. This can be done without changing
the standard driver for the host controller. There is currently
support for three USB signals, PWRON, VBUS_PRESENT and PWRFLT. This
driver will allow the remapping of any of these three signals based
on settings in the Device Tree node for the driver. The driver was
written so that it could handle additional signals added in the
future by just adding the correct properties to the DT node.
Below is an example of a DT node that would remap all three
signals:
usb_pinmap: usb-pinmap@22000d0 {
compatible = "brcm,usb-pinmap";
reg = <0x22000d0 0x4>;
in-gpios = <&gpio 18 0>, <&gpio 19 0>;
brcm,in-functions = "VBUS", "PWRFLT";
brcm,in-masks = <0x8000 0x40000 0x10000 0x80000>;
out-gpios = <&gpio 20 0>;
brcm,out-functions = "PWRON";
brcm,out-masks = <0x20000 0x800000 0x400000 0x200000>;
interrupts = <0x0 0xb2 0x4>;
};
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20201012200007.8862-3-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-12 20:00:07 +00:00
|
|
|
|
|
|
|
pdata = devm_kzalloc(&pdev->dev,
|
|
|
|
sizeof(*pdata) +
|
|
|
|
(sizeof(struct in_pin) * in_count) +
|
|
|
|
(sizeof(struct out_pin) * out_count), GFP_KERNEL);
|
|
|
|
if (!pdata)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
pdata->in_count = in_count;
|
|
|
|
pdata->out_count = out_count;
|
|
|
|
pdata->in_pins = (struct in_pin *)(pdata + 1);
|
|
|
|
pdata->out_pins = (struct out_pin *)(pdata->in_pins + in_count);
|
|
|
|
|
|
|
|
pdata->regs = devm_ioremap(&pdev->dev, r->start, resource_size(r));
|
2020-11-02 07:56:55 +00:00
|
|
|
if (!pdata->regs)
|
|
|
|
return -ENOMEM;
|
usb: Add driver to allow any GPIO to be used for 7211 USB signals
The Broadcom 7211 has new functionality that allows some USB low
speed side band signals, that go from the XHCI host controller to
pins on the chip, to be remapped to use any GPIO pin instead of the
limited set selectable by hardware. This can be done without changing
the standard driver for the host controller. There is currently
support for three USB signals, PWRON, VBUS_PRESENT and PWRFLT. This
driver will allow the remapping of any of these three signals based
on settings in the Device Tree node for the driver. The driver was
written so that it could handle additional signals added in the
future by just adding the correct properties to the DT node.
Below is an example of a DT node that would remap all three
signals:
usb_pinmap: usb-pinmap@22000d0 {
compatible = "brcm,usb-pinmap";
reg = <0x22000d0 0x4>;
in-gpios = <&gpio 18 0>, <&gpio 19 0>;
brcm,in-functions = "VBUS", "PWRFLT";
brcm,in-masks = <0x8000 0x40000 0x10000 0x80000>;
out-gpios = <&gpio 20 0>;
brcm,out-functions = "PWRON";
brcm,out-masks = <0x20000 0x800000 0x400000 0x200000>;
interrupts = <0x0 0xb2 0x4>;
};
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20201012200007.8862-3-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-12 20:00:07 +00:00
|
|
|
platform_set_drvdata(pdev, pdata);
|
|
|
|
|
|
|
|
err = parse_pins(&pdev->dev, dn, pdata);
|
|
|
|
if (err)
|
|
|
|
return err;
|
|
|
|
|
|
|
|
sync_all_pins(pdata);
|
|
|
|
|
|
|
|
if (out_count) {
|
|
|
|
|
|
|
|
/* Enable interrupt for out pins */
|
|
|
|
irq = platform_get_irq(pdev, 0);
|
2021-08-09 20:45:15 +00:00
|
|
|
if (irq < 0)
|
|
|
|
return irq;
|
usb: Add driver to allow any GPIO to be used for 7211 USB signals
The Broadcom 7211 has new functionality that allows some USB low
speed side band signals, that go from the XHCI host controller to
pins on the chip, to be remapped to use any GPIO pin instead of the
limited set selectable by hardware. This can be done without changing
the standard driver for the host controller. There is currently
support for three USB signals, PWRON, VBUS_PRESENT and PWRFLT. This
driver will allow the remapping of any of these three signals based
on settings in the Device Tree node for the driver. The driver was
written so that it could handle additional signals added in the
future by just adding the correct properties to the DT node.
Below is an example of a DT node that would remap all three
signals:
usb_pinmap: usb-pinmap@22000d0 {
compatible = "brcm,usb-pinmap";
reg = <0x22000d0 0x4>;
in-gpios = <&gpio 18 0>, <&gpio 19 0>;
brcm,in-functions = "VBUS", "PWRFLT";
brcm,in-masks = <0x8000 0x40000 0x10000 0x80000>;
out-gpios = <&gpio 20 0>;
brcm,out-functions = "PWRON";
brcm,out-masks = <0x20000 0x800000 0x400000 0x200000>;
interrupts = <0x0 0xb2 0x4>;
};
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20201012200007.8862-3-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-12 20:00:07 +00:00
|
|
|
err = devm_request_irq(&pdev->dev, irq,
|
|
|
|
brcmstb_usb_pinmap_ovr_isr,
|
|
|
|
IRQF_TRIGGER_RISING,
|
|
|
|
pdev->name, pdata);
|
|
|
|
if (err < 0) {
|
|
|
|
dev_err(&pdev->dev, "Error requesting IRQ\n");
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
for (x = 0, pin = pdata->in_pins; x < pdata->in_count; x++, pin++) {
|
|
|
|
irq = gpiod_to_irq(pin->gpiod);
|
|
|
|
if (irq < 0) {
|
|
|
|
dev_err(&pdev->dev, "Error getting IRQ for %s pin\n",
|
|
|
|
pin->name);
|
|
|
|
return irq;
|
|
|
|
}
|
|
|
|
err = devm_request_irq(&pdev->dev, irq,
|
|
|
|
brcmstb_usb_pinmap_gpio_isr,
|
|
|
|
IRQF_SHARED | IRQF_TRIGGER_RISING |
|
|
|
|
IRQF_TRIGGER_FALLING,
|
|
|
|
pdev->name, pin);
|
|
|
|
if (err < 0) {
|
|
|
|
dev_err(&pdev->dev, "Error requesting IRQ for %s pin\n",
|
|
|
|
pin->name);
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
dev_dbg(&pdev->dev, "Driver probe succeeded\n");
|
|
|
|
dev_dbg(&pdev->dev, "In pin count: %d, out pin count: %d\n",
|
|
|
|
pdata->in_count, pdata->out_count);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
static const struct of_device_id brcmstb_usb_pinmap_of_match[] = {
|
|
|
|
{ .compatible = "brcm,usb-pinmap" },
|
|
|
|
{ },
|
|
|
|
};
|
|
|
|
|
|
|
|
static struct platform_driver brcmstb_usb_pinmap_driver = {
|
|
|
|
.driver = {
|
|
|
|
.name = "brcm-usb-pinmap",
|
|
|
|
.of_match_table = brcmstb_usb_pinmap_of_match,
|
|
|
|
},
|
|
|
|
};
|
|
|
|
|
|
|
|
static int __init brcmstb_usb_pinmap_init(void)
|
|
|
|
{
|
|
|
|
return platform_driver_probe(&brcmstb_usb_pinmap_driver,
|
|
|
|
brcmstb_usb_pinmap_probe);
|
|
|
|
}
|
|
|
|
|
|
|
|
module_init(brcmstb_usb_pinmap_init);
|
|
|
|
MODULE_AUTHOR("Al Cooper <alcooperx@gmail.com>");
|
|
|
|
MODULE_DESCRIPTION("Broadcom USB Pinmap Driver");
|
|
|
|
MODULE_LICENSE("GPL");
|