linux-stable/drivers/mfd/ti_am335x_tscadc.c

359 lines
9.2 KiB
C
Raw Normal View History

/*
* TI Touch Screen / ADC MFD driver
*
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/regmap.h>
#include <linux/mfd/core.h>
#include <linux/pm_runtime.h>
#include <linux/of.h>
#include <linux/of_device.h>
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
#include <linux/sched.h>
#include <linux/mfd/ti_am335x_tscadc.h>
static const struct regmap_config tscadc_regmap_config = {
.name = "ti_tscadc",
.reg_bits = 32,
.reg_stride = 4,
.val_bits = 32,
};
void am335x_tsc_se_set_cache(struct ti_tscadc_dev *tscadc, u32 val)
{
unsigned long flags;
spin_lock_irqsave(&tscadc->reg_lock, flags);
tscadc->reg_se_cache |= val;
if (tscadc->adc_waiting)
wake_up(&tscadc->reg_se_wait);
else if (!tscadc->adc_in_use)
regmap_write(tscadc->regmap, REG_SE, tscadc->reg_se_cache);
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
spin_unlock_irqrestore(&tscadc->reg_lock, flags);
}
EXPORT_SYMBOL_GPL(am335x_tsc_se_set_cache);
static void am335x_tscadc_need_adc(struct ti_tscadc_dev *tscadc)
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
{
DEFINE_WAIT(wait);
u32 reg;
regmap_read(tscadc->regmap, REG_ADCFSM, &reg);
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
if (reg & SEQ_STATUS) {
tscadc->adc_waiting = true;
prepare_to_wait(&tscadc->reg_se_wait, &wait,
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
TASK_UNINTERRUPTIBLE);
spin_unlock_irq(&tscadc->reg_lock);
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
schedule();
spin_lock_irq(&tscadc->reg_lock);
finish_wait(&tscadc->reg_se_wait, &wait);
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
/*
* Sequencer should either be idle or
* busy applying the charge step.
*/
regmap_read(tscadc->regmap, REG_ADCFSM, &reg);
WARN_ON((reg & SEQ_STATUS) && !(reg & CHARGE_STEP));
tscadc->adc_waiting = false;
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
}
tscadc->adc_in_use = true;
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
}
void am335x_tsc_se_set_once(struct ti_tscadc_dev *tscadc, u32 val)
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
{
spin_lock_irq(&tscadc->reg_lock);
am335x_tscadc_need_adc(tscadc);
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
regmap_write(tscadc->regmap, REG_SE, val);
spin_unlock_irq(&tscadc->reg_lock);
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
}
EXPORT_SYMBOL_GPL(am335x_tsc_se_set_once);
void am335x_tsc_se_adc_done(struct ti_tscadc_dev *tscadc)
{
unsigned long flags;
spin_lock_irqsave(&tscadc->reg_lock, flags);
tscadc->adc_in_use = false;
regmap_write(tscadc->regmap, REG_SE, tscadc->reg_se_cache);
spin_unlock_irqrestore(&tscadc->reg_lock, flags);
}
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
EXPORT_SYMBOL_GPL(am335x_tsc_se_adc_done);
void am335x_tsc_se_clr(struct ti_tscadc_dev *tscadc, u32 val)
{
unsigned long flags;
spin_lock_irqsave(&tscadc->reg_lock, flags);
tscadc->reg_se_cache &= ~val;
regmap_write(tscadc->regmap, REG_SE, tscadc->reg_se_cache);
spin_unlock_irqrestore(&tscadc->reg_lock, flags);
}
EXPORT_SYMBOL_GPL(am335x_tsc_se_clr);
static void tscadc_idle_config(struct ti_tscadc_dev *tscadc)
{
unsigned int idleconfig;
idleconfig = STEPCONFIG_YNN | STEPCONFIG_INM_ADCREFM |
STEPCONFIG_INP_ADCREFM | STEPCONFIG_YPN;
regmap_write(tscadc->regmap, REG_IDLECONFIG, idleconfig);
}
static int ti_tscadc_probe(struct platform_device *pdev)
{
struct ti_tscadc_dev *tscadc;
struct resource *res;
struct clk *clk;
struct device_node *node = pdev->dev.of_node;
struct mfd_cell *cell;
struct property *prop;
const __be32 *cur;
u32 val;
int err, ctrl;
int clock_rate;
int tsc_wires = 0, adc_channels = 0, total_channels;
int readouts = 0;
if (!pdev->dev.of_node) {
dev_err(&pdev->dev, "Could not find valid DT data.\n");
return -EINVAL;
}
node = of_get_child_by_name(pdev->dev.of_node, "tsc");
of_property_read_u32(node, "ti,wires", &tsc_wires);
of_property_read_u32(node, "ti,coordiante-readouts", &readouts);
node = of_get_child_by_name(pdev->dev.of_node, "adc");
of_property_for_each_u32(node, "ti,adc-channels", prop, cur, val) {
adc_channels++;
if (val > 7) {
dev_err(&pdev->dev, " PIN numbers are 0..7 (not %d)\n",
val);
return -EINVAL;
}
}
total_channels = tsc_wires + adc_channels;
if (total_channels > 8) {
dev_err(&pdev->dev, "Number of i/p channels more than 8\n");
return -EINVAL;
}
if (total_channels == 0) {
dev_err(&pdev->dev, "Need atleast one channel.\n");
return -EINVAL;
}
if (readouts * 2 + 2 + adc_channels > 16) {
dev_err(&pdev->dev, "Too many step configurations requested\n");
return -EINVAL;
}
/* Allocate memory for device */
tscadc = devm_kzalloc(&pdev->dev, sizeof(*tscadc), GFP_KERNEL);
if (!tscadc) {
dev_err(&pdev->dev, "failed to allocate memory.\n");
return -ENOMEM;
}
tscadc->dev = &pdev->dev;
err = platform_get_irq(pdev, 0);
if (err < 0) {
dev_err(&pdev->dev, "no irq ID is specified.\n");
goto ret;
} else
tscadc->irq = err;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
tscadc->tscadc_phys_base = res->start;
tscadc->tscadc_base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(tscadc->tscadc_base))
return PTR_ERR(tscadc->tscadc_base);
tscadc->regmap = devm_regmap_init_mmio(&pdev->dev,
tscadc->tscadc_base, &tscadc_regmap_config);
if (IS_ERR(tscadc->regmap)) {
dev_err(&pdev->dev, "regmap init failed\n");
err = PTR_ERR(tscadc->regmap);
goto ret;
}
spin_lock_init(&tscadc->reg_lock);
mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization The ADC driver always programs all possible ADC values and discards them except for the value IIO asked for. On the am335x-evm the driver programs four values and it takes 500us to gather them. Reducing the number of conversations down to the (required) one also reduces the busy loop down to 125us. This leads to another error, namely the FIFOCOUNT register is sometimes (like one out of 10 attempts) not updated in time leading to EBUSY. The next read has the FIFOCOUNT register updated. Checking for the ADCSTAT register for being idle isn't a good choice either. The problem is that if TSC is used at the same time, the HW completes the conversation for ADC *and* before the driver noticed it, the HW begins to perform a TSC conversation and so the driver never seen the HW idle. The next time we would have two values in the FIFO but since the driver reads everything we always see the current one. So instead of polling for the IDLE bit in ADCStatus register, we should check the FIFOCOUNT register. It should be one instead of zero because we request one value. This change in turn leads to another error. Sometimes if TSC & ADC are used together the TSC starts generating interrupts even if nobody actually touched the touchscreen. The interrupts seem valid because TSC's FIFO is filled with values for each channel of the TSC. This condition stops after a few ADC reads but will occur again. Not good. On top of this (even without the changes I just mentioned) there is a ADC & TSC lockup condition which was reported to me by Jeff Lance including the following test case: A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw" and a mug on touch screen. With this setup, the hardware will lockup after something between 20 minutes and it could take up to a couple of hours. During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is idle and busy at the same time which is an invalid condition. For all this reasons I decided to rework this TSC/ADC part and add a handshake / synchronization here: First the ADC signals that it needs the HW and writes a 0 mask into the SE register. The HW (if active) will complete the current conversation and become idle. The TSC driver will gather the values from the FIFO (woken up by an interrupt) and won't "enable" another conversation. Instead it will wake up the ADC driver which is already waiting. The ADC driver will start "its" conversation and once it is done, it will enable the TSC steps so the TSC will work again. After this rework I haven't observed the lockup so far. Plus the busy loop has been reduced from 500us to 125us. The continues-read mode remains unchanged. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-12-19 15:28:31 +00:00
init_waitqueue_head(&tscadc->reg_se_wait);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
/*
* The TSC_ADC_Subsystem has 2 clock domains
* OCP_CLK and ADC_CLK.
* The ADC clock is expected to run at target of 3MHz,
* and expected to capture 12-bit data at a rate of 200 KSPS.
* The TSC_ADC_SS controller design assumes the OCP clock is
* at least 6x faster than the ADC clock.
*/
clk = clk_get(&pdev->dev, "adc_tsc_fck");
if (IS_ERR(clk)) {
dev_err(&pdev->dev, "failed to get TSC fck\n");
err = PTR_ERR(clk);
goto err_disable_clk;
}
clock_rate = clk_get_rate(clk);
clk_put(clk);
tscadc->clk_div = clock_rate / ADC_CLK;
/* TSCADC_CLKDIV needs to be configured to the value minus 1 */
tscadc->clk_div--;
regmap_write(tscadc->regmap, REG_CLKDIV, tscadc->clk_div);
/* Set the control register bits */
ctrl = CNTRLREG_STEPCONFIGWRT | CNTRLREG_STEPID;
regmap_write(tscadc->regmap, REG_CTRL, ctrl);
/* Set register bits for Idle Config Mode */
if (tsc_wires > 0) {
tscadc->tsc_wires = tsc_wires;
if (tsc_wires == 5)
ctrl |= CNTRLREG_5WIRE | CNTRLREG_TSCENB;
else
ctrl |= CNTRLREG_4WIRE | CNTRLREG_TSCENB;
tscadc_idle_config(tscadc);
}
/* Enable the TSC module enable bit */
ctrl |= CNTRLREG_TSCSSENB;
regmap_write(tscadc->regmap, REG_CTRL, ctrl);
tscadc->used_cells = 0;
tscadc->tsc_cell = -1;
tscadc->adc_cell = -1;
/* TSC Cell */
if (tsc_wires > 0) {
tscadc->tsc_cell = tscadc->used_cells;
cell = &tscadc->cells[tscadc->used_cells++];
cell->name = "TI-am335x-tsc";
cell->of_compatible = "ti,am3359-tsc";
cell->platform_data = &tscadc;
cell->pdata_size = sizeof(tscadc);
}
/* ADC Cell */
if (adc_channels > 0) {
tscadc->adc_cell = tscadc->used_cells;
cell = &tscadc->cells[tscadc->used_cells++];
cell->name = "TI-am335x-adc";
cell->of_compatible = "ti,am3359-adc";
cell->platform_data = &tscadc;
cell->pdata_size = sizeof(tscadc);
}
err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
tscadc->used_cells, NULL, 0, NULL);
if (err < 0)
goto err_disable_clk;
device_init_wakeup(&pdev->dev, true);
platform_set_drvdata(pdev, tscadc);
return 0;
err_disable_clk:
pm_runtime_put_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
ret:
return err;
}
static int ti_tscadc_remove(struct platform_device *pdev)
{
struct ti_tscadc_dev *tscadc = platform_get_drvdata(pdev);
regmap_write(tscadc->regmap, REG_SE, 0x00);
pm_runtime_put_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
mfd_remove_devices(tscadc->dev);
return 0;
}
static int __maybe_unused tscadc_suspend(struct device *dev)
{
struct ti_tscadc_dev *tscadc = dev_get_drvdata(dev);
regmap_write(tscadc->regmap, REG_SE, 0x00);
pm_runtime_put_sync(dev);
return 0;
}
static int __maybe_unused tscadc_resume(struct device *dev)
{
struct ti_tscadc_dev *tscadc = dev_get_drvdata(dev);
u32 ctrl;
pm_runtime_get_sync(dev);
/* context restore */
ctrl = CNTRLREG_STEPCONFIGWRT | CNTRLREG_STEPID;
regmap_write(tscadc->regmap, REG_CTRL, ctrl);
if (tscadc->tsc_cell != -1) {
if (tscadc->tsc_wires == 5)
ctrl |= CNTRLREG_5WIRE | CNTRLREG_TSCENB;
else
ctrl |= CNTRLREG_4WIRE | CNTRLREG_TSCENB;
tscadc_idle_config(tscadc);
}
ctrl |= CNTRLREG_TSCSSENB;
regmap_write(tscadc->regmap, REG_CTRL, ctrl);
regmap_write(tscadc->regmap, REG_CLKDIV, tscadc->clk_div);
return 0;
}
static SIMPLE_DEV_PM_OPS(tscadc_pm_ops, tscadc_suspend, tscadc_resume);
static const struct of_device_id ti_tscadc_dt_ids[] = {
{ .compatible = "ti,am3359-tscadc", },
{ }
};
MODULE_DEVICE_TABLE(of, ti_tscadc_dt_ids);
static struct platform_driver ti_tscadc_driver = {
.driver = {
.name = "ti_am3359-tscadc",
.pm = &tscadc_pm_ops,
.of_match_table = ti_tscadc_dt_ids,
},
.probe = ti_tscadc_probe,
.remove = ti_tscadc_remove,
};
module_platform_driver(ti_tscadc_driver);
MODULE_DESCRIPTION("TI touchscreen / ADC MFD controller driver");
MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
MODULE_LICENSE("GPL");