ARM: at91: Add support for board aks-cdu

Add support for our "aks-cdu" board based up on Telit's module GE863 Pro3.
It has more uarts, leds, another nand partitioning.

Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[nicolas.ferre@atmel.com: correction of the dts file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit is contained in:
Jiri Prchal 2012-07-09 10:05:18 +02:00 committed by Nicolas Ferre
parent 2e8e4711fe
commit 3c68bb4821
2 changed files with 114 additions and 0 deletions

View File

@ -0,0 +1,113 @@
/*
* aks-cdu.dts - Device Tree file for AK signal CDU
*
* Copyright (C) 2012 AK signal Brno a.s.
* 2012 Jiri Prchal <jiri.prchal@aksignal.cz>
*
* Licensed under GPLv2 or later.
*/
/dts-v1/;
/include/ "ge863-pro3.dtsi"
/ {
chosen {
bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs";
};
ahb {
apb {
usart0: serial@fffb0000 {
status = "okay";
};
usart1: serial@fffb4000 {
status = "okay";
linux,rs485-enabled-at-boot-time;
rs485-rts-delay = <0 0>;
};
usart2: serial@fffb8000 {
status = "okay";
linux,rs485-enabled-at-boot-time;
rs485-rts-delay = <0 0>;
};
usart3: serial@fffd0000 {
status = "okay";
linux,rs485-enabled-at-boot-time;
rs485-rts-delay = <0 0>;
};
macb0: ethernet@fffc4000 {
phy-mode = "rmii";
status = "okay";
};
usb1: gadget@fffa4000 {
atmel,vbus-gpio = <&pioC 15 0>;
status = "okay";
};
};
usb0: ohci@00500000 {
num-ports = <2>;
status = "okay";
};
nand0: nand@40000000 {
nand-bus-width = <8>;
nand-ecc-mode = "soft";
nand-on-flash-bbt;
status = "okay";
bootstrap@0 {
label = "bootstrap";
reg = <0x0 0x40000>;
};
uboot@40000 {
label = "uboot";
reg = <0x40000 0x80000>;
};
ubootenv@c0000 {
label = "ubootenv";
reg = <0xc0000 0x40000>;
};
kernel@100000 {
label = "kernel";
reg = <0x100000 0x400000>;
};
rootfs@500000 {
label = "rootfs";
reg = <0x500000 0x7b00000>;
};
};
};
leds {
compatible = "gpio-leds";
red {
gpios = <&pioC 10 0>;
linux,default-trigger = "none";
};
green {
gpios = <&pioA 5 1>;
linux,default-trigger = "none";
default-state = "on";
};
yellow {
gpios = <&pioB 20 1>;
linux,default-trigger = "none";
};
blue {
gpios = <&pioB 21 1>;
linux,default-trigger = "none";
};
};
};

View File

@ -15,6 +15,7 @@ endif
# Keep dtb files sorted alphabetically for each SoC
# sam9260
dtb-$(CONFIG_MACH_AT91SAM_DT) += aks-cdu.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += evk-pro3.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb