diff --git a/MAINTAINERS b/MAINTAINERS index 48a65c3a4189..e38ba7e45744 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2195,6 +2195,7 @@ F: drivers/clk/uniphier/ F: drivers/gpio/gpio-uniphier.c F: drivers/i2c/busses/i2c-uniphier* F: drivers/irqchip/irq-uniphier-aidet.c +F: drivers/mmc/host/uniphier-sd.c F: drivers/pinctrl/uniphier/ F: drivers/reset/reset-uniphier.c F: drivers/tty/serial/8250/8250_uniphier.c diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 4e6b3d35d0c6..d09feb6c4584 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -631,6 +631,16 @@ config MMC_SDHI_INTERNAL_DMAC using on-chip bus mastering. This supports the controllers found in arm64 based SoCs. +config MMC_UNIPHIER + tristate "UniPhier SD/eMMC Host Controller support" + depends on ARCH_UNIPHIER || COMPILE_TEST + depends on OF + select MMC_TMIO_CORE + help + This provides support for the SD/eMMC controller found in + UniPhier SoCs. The eMMC variant of this controller is used + only for 32-bit SoCs. + config MMC_CB710 tristate "ENE CB710 MMC/SD Interface support" depends on PCI diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index ce8398e6f2c0..a835d1a0546d 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -42,6 +42,7 @@ obj-$(CONFIG_MMC_TMIO_CORE) += tmio_mmc_core.o obj-$(CONFIG_MMC_SDHI) += renesas_sdhi_core.o obj-$(CONFIG_MMC_SDHI_SYS_DMAC) += renesas_sdhi_sys_dmac.o obj-$(CONFIG_MMC_SDHI_INTERNAL_DMAC) += renesas_sdhi_internal_dmac.o +obj-$(CONFIG_MMC_UNIPHIER) += uniphier-sd.o obj-$(CONFIG_MMC_CB710) += cb710-mmc.o obj-$(CONFIG_MMC_VIA_SDMMC) += via-sdmmc.o octeon-mmc-objs := cavium.o cavium-octeon.o diff --git a/drivers/mmc/host/uniphier-sd.c b/drivers/mmc/host/uniphier-sd.c new file mode 100644 index 000000000000..10e7b30c792a --- /dev/null +++ b/drivers/mmc/host/uniphier-sd.c @@ -0,0 +1,693 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2017-2018 Socionext Inc. +// Author: Masahiro Yamada + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "tmio_mmc.h" + +#define UNIPHIER_SD_CLK_CTL_DIV1024 BIT(16) +#define UNIPHIER_SD_CLK_CTL_DIV1 BIT(10) +#define UNIPHIER_SD_CLKCTL_OFFEN BIT(9) // auto SDCLK stop +#define UNIPHIER_SD_CC_EXT_MODE 0x1b0 +#define UNIPHIER_SD_CC_EXT_MODE_DMA BIT(1) +#define UNIPHIER_SD_HOST_MODE 0x1c8 +#define UNIPHIER_SD_VOLT 0x1e4 +#define UNIPHIER_SD_VOLT_MASK GENMASK(1, 0) +#define UNIPHIER_SD_VOLT_OFF 0 +#define UNIPHIER_SD_VOLT_330 1 // 3.3V signal +#define UNIPHIER_SD_VOLT_180 2 // 1.8V signal +#define UNIPHIER_SD_DMA_MODE 0x410 +#define UNIPHIER_SD_DMA_MODE_DIR_MASK GENMASK(17, 16) +#define UNIPHIER_SD_DMA_MODE_DIR_TO_DEV 0 +#define UNIPHIER_SD_DMA_MODE_DIR_FROM_DEV 1 +#define UNIPHIER_SD_DMA_MODE_WIDTH_MASK GENMASK(5, 4) +#define UNIPHIER_SD_DMA_MODE_WIDTH_8 0 +#define UNIPHIER_SD_DMA_MODE_WIDTH_16 1 +#define UNIPHIER_SD_DMA_MODE_WIDTH_32 2 +#define UNIPHIER_SD_DMA_MODE_WIDTH_64 3 +#define UNIPHIER_SD_DMA_MODE_ADDR_INC BIT(0) // 1: inc, 0: fixed +#define UNIPHIER_SD_DMA_CTL 0x414 +#define UNIPHIER_SD_DMA_CTL_START BIT(0) // start DMA (auto cleared) +#define UNIPHIER_SD_DMA_RST 0x418 +#define UNIPHIER_SD_DMA_RST_CH1 BIT(9) +#define UNIPHIER_SD_DMA_RST_CH0 BIT(8) +#define UNIPHIER_SD_DMA_ADDR_L 0x440 +#define UNIPHIER_SD_DMA_ADDR_H 0x444 + +/* + * IP is extended to support various features: built-in DMA engine, + * 1/1024 divisor, etc. + */ +#define UNIPHIER_SD_CAP_EXTENDED_IP BIT(0) +/* RX channel of the built-in DMA controller is broken (Pro5) */ +#define UNIPHIER_SD_CAP_BROKEN_DMA_RX BIT(1) + +struct uniphier_sd_priv { + struct tmio_mmc_data tmio_data; + struct pinctrl *pinctrl; + struct pinctrl_state *pinstate_default; + struct pinctrl_state *pinstate_uhs; + struct clk *clk; + struct reset_control *rst; + struct reset_control *rst_br; + struct reset_control *rst_hw; + struct dma_chan *chan; + enum dma_data_direction dma_dir; + unsigned long clk_rate; + unsigned long caps; +}; + +static void *uniphier_sd_priv(struct tmio_mmc_host *host) +{ + return container_of(host->pdata, struct uniphier_sd_priv, tmio_data); +} + +static void uniphier_sd_dma_endisable(struct tmio_mmc_host *host, int enable) +{ + sd_ctrl_write16(host, CTL_DMA_ENABLE, DMA_ENABLE_DMASDRW); +} + +/* external DMA engine */ +static void uniphier_sd_external_dma_issue(unsigned long arg) +{ + struct tmio_mmc_host *host = (void *)arg; + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + + uniphier_sd_dma_endisable(host, 1); + dma_async_issue_pending(priv->chan); +} + +static void uniphier_sd_external_dma_callback(void *param, + const struct dmaengine_result *result) +{ + struct tmio_mmc_host *host = param; + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + unsigned long flags; + + dma_unmap_sg(mmc_dev(host->mmc), host->sg_ptr, host->sg_len, + priv->dma_dir); + + spin_lock_irqsave(&host->lock, flags); + + if (result->result == DMA_TRANS_NOERROR) { + /* + * When the external DMA engine is enabled, strangely enough, + * the DATAEND flag can be asserted even if the DMA engine has + * not been kicked yet. Enable the TMIO_STAT_DATAEND irq only + * after we make sure the DMA engine finishes the transfer, + * hence, in this callback. + */ + tmio_mmc_enable_mmc_irqs(host, TMIO_STAT_DATAEND); + } else { + host->data->error = -ETIMEDOUT; + tmio_mmc_do_data_irq(host); + } + + spin_unlock_irqrestore(&host->lock, flags); +} + +static void uniphier_sd_external_dma_start(struct tmio_mmc_host *host, + struct mmc_data *data) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + enum dma_transfer_direction dma_tx_dir; + struct dma_async_tx_descriptor *desc; + dma_cookie_t cookie; + int sg_len; + + if (!priv->chan) + goto force_pio; + + if (data->flags & MMC_DATA_READ) { + priv->dma_dir = DMA_FROM_DEVICE; + dma_tx_dir = DMA_DEV_TO_MEM; + } else { + priv->dma_dir = DMA_TO_DEVICE; + dma_tx_dir = DMA_MEM_TO_DEV; + } + + sg_len = dma_map_sg(mmc_dev(host->mmc), host->sg_ptr, host->sg_len, + priv->dma_dir); + if (sg_len == 0) + goto force_pio; + + desc = dmaengine_prep_slave_sg(priv->chan, host->sg_ptr, sg_len, + dma_tx_dir, DMA_CTRL_ACK); + if (!desc) + goto unmap_sg; + + desc->callback_result = uniphier_sd_external_dma_callback; + desc->callback_param = host; + + cookie = dmaengine_submit(desc); + if (cookie < 0) + goto unmap_sg; + + return; + +unmap_sg: + dma_unmap_sg(mmc_dev(host->mmc), host->sg_ptr, host->sg_len, + priv->dma_dir); +force_pio: + host->force_pio = true; + uniphier_sd_dma_endisable(host, 0); +} + +static void uniphier_sd_external_dma_enable(struct tmio_mmc_host *host, + bool enable) +{ +} + +static void uniphier_sd_external_dma_request(struct tmio_mmc_host *host, + struct tmio_mmc_data *pdata) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + struct dma_chan *chan; + + chan = dma_request_chan(mmc_dev(host->mmc), "rx-tx"); + if (IS_ERR(chan)) { + dev_warn(mmc_dev(host->mmc), + "failed to request DMA channel. falling back to PIO\n"); + return; /* just use PIO even for -EPROBE_DEFER */ + } + + /* this driver uses a single channel for both RX an TX */ + priv->chan = chan; + host->chan_rx = chan; + host->chan_tx = chan; + + tasklet_init(&host->dma_issue, uniphier_sd_external_dma_issue, + (unsigned long)host); +} + +static void uniphier_sd_external_dma_release(struct tmio_mmc_host *host) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + + if (priv->chan) + dma_release_channel(priv->chan); +} + +static void uniphier_sd_external_dma_abort(struct tmio_mmc_host *host) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + + uniphier_sd_dma_endisable(host, 0); + + if (priv->chan) + dmaengine_terminate_sync(priv->chan); +} + +static void uniphier_sd_external_dma_dataend(struct tmio_mmc_host *host) +{ + uniphier_sd_dma_endisable(host, 0); + + tmio_mmc_do_data_irq(host); +} + +static const struct tmio_mmc_dma_ops uniphier_sd_external_dma_ops = { + .start = uniphier_sd_external_dma_start, + .enable = uniphier_sd_external_dma_enable, + .request = uniphier_sd_external_dma_request, + .release = uniphier_sd_external_dma_release, + .abort = uniphier_sd_external_dma_abort, + .dataend = uniphier_sd_external_dma_dataend, +}; + +static void uniphier_sd_internal_dma_issue(unsigned long arg) +{ + struct tmio_mmc_host *host = (void *)arg; + unsigned long flags; + + spin_lock_irqsave(&host->lock, flags); + tmio_mmc_enable_mmc_irqs(host, TMIO_STAT_DATAEND); + spin_unlock_irqrestore(&host->lock, flags); + + uniphier_sd_dma_endisable(host, 1); + writel(UNIPHIER_SD_DMA_CTL_START, host->ctl + UNIPHIER_SD_DMA_CTL); +} + +static void uniphier_sd_internal_dma_start(struct tmio_mmc_host *host, + struct mmc_data *data) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + struct scatterlist *sg = host->sg_ptr; + dma_addr_t dma_addr; + unsigned int dma_mode_dir; + u32 dma_mode; + int sg_len; + + if (WARN_ON(host->sg_len != 1)) + goto force_pio; + + if (!IS_ALIGNED(sg->offset, 8)) + goto force_pio; + + if (data->flags & MMC_DATA_READ) { + priv->dma_dir = DMA_FROM_DEVICE; + dma_mode_dir = UNIPHIER_SD_DMA_MODE_DIR_FROM_DEV; + } else { + priv->dma_dir = DMA_TO_DEVICE; + dma_mode_dir = UNIPHIER_SD_DMA_MODE_DIR_TO_DEV; + } + + sg_len = dma_map_sg(mmc_dev(host->mmc), sg, 1, priv->dma_dir); + if (sg_len == 0) + goto force_pio; + + dma_mode = FIELD_PREP(UNIPHIER_SD_DMA_MODE_DIR_MASK, dma_mode_dir); + dma_mode |= FIELD_PREP(UNIPHIER_SD_DMA_MODE_WIDTH_MASK, + UNIPHIER_SD_DMA_MODE_WIDTH_64); + dma_mode |= UNIPHIER_SD_DMA_MODE_ADDR_INC; + + writel(dma_mode, host->ctl + UNIPHIER_SD_DMA_MODE); + + dma_addr = sg_dma_address(data->sg); + writel(lower_32_bits(dma_addr), host->ctl + UNIPHIER_SD_DMA_ADDR_L); + writel(upper_32_bits(dma_addr), host->ctl + UNIPHIER_SD_DMA_ADDR_H); + + return; +force_pio: + host->force_pio = true; + uniphier_sd_dma_endisable(host, 0); +} + +static void uniphier_sd_internal_dma_enable(struct tmio_mmc_host *host, + bool enable) +{ +} + +static void uniphier_sd_internal_dma_request(struct tmio_mmc_host *host, + struct tmio_mmc_data *pdata) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + + /* + * Due to a hardware bug, Pro5 cannot use DMA for RX. + * We can still use DMA for TX, but PIO for RX. + */ + if (!(priv->caps & UNIPHIER_SD_CAP_BROKEN_DMA_RX)) + host->chan_rx = (void *)0xdeadbeaf; + + host->chan_tx = (void *)0xdeadbeaf; + + tasklet_init(&host->dma_issue, uniphier_sd_internal_dma_issue, + (unsigned long)host); +} + +static void uniphier_sd_internal_dma_release(struct tmio_mmc_host *host) +{ + /* Each value is set to zero to assume "disabling" each DMA */ + host->chan_rx = NULL; + host->chan_tx = NULL; +} + +static void uniphier_sd_internal_dma_abort(struct tmio_mmc_host *host) +{ + u32 tmp; + + uniphier_sd_dma_endisable(host, 0); + + tmp = readl(host->ctl + UNIPHIER_SD_DMA_RST); + tmp &= ~(UNIPHIER_SD_DMA_RST_CH1 | UNIPHIER_SD_DMA_RST_CH0); + writel(tmp, host->ctl + UNIPHIER_SD_DMA_RST); + + tmp |= UNIPHIER_SD_DMA_RST_CH1 | UNIPHIER_SD_DMA_RST_CH0; + writel(tmp, host->ctl + UNIPHIER_SD_DMA_RST); +} + +static void uniphier_sd_internal_dma_dataend(struct tmio_mmc_host *host) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + + uniphier_sd_dma_endisable(host, 0); + dma_unmap_sg(mmc_dev(host->mmc), host->sg_ptr, 1, priv->dma_dir); + + tmio_mmc_do_data_irq(host); +} + +static const struct tmio_mmc_dma_ops uniphier_sd_internal_dma_ops = { + .start = uniphier_sd_internal_dma_start, + .enable = uniphier_sd_internal_dma_enable, + .request = uniphier_sd_internal_dma_request, + .release = uniphier_sd_internal_dma_release, + .abort = uniphier_sd_internal_dma_abort, + .dataend = uniphier_sd_internal_dma_dataend, +}; + +static int uniphier_sd_clk_enable(struct tmio_mmc_host *host) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + struct mmc_host *mmc = host->mmc; + int ret; + + ret = clk_prepare_enable(priv->clk); + if (ret) + return ret; + + ret = clk_set_rate(priv->clk, ULONG_MAX); + if (ret) + goto disable_clk; + + priv->clk_rate = clk_get_rate(priv->clk); + + /* If max-frequency property is set, use it. */ + if (!mmc->f_max) + mmc->f_max = priv->clk_rate; + + /* + * 1/512 is the finest divisor in the original IP. Newer versions + * also supports 1/1024 divisor. (UniPhier-specific extension) + */ + if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) + mmc->f_min = priv->clk_rate / 1024; + else + mmc->f_min = priv->clk_rate / 512; + + ret = reset_control_deassert(priv->rst); + if (ret) + goto disable_clk; + + ret = reset_control_deassert(priv->rst_br); + if (ret) + goto assert_rst; + + return 0; + +assert_rst: + reset_control_assert(priv->rst); +disable_clk: + clk_disable_unprepare(priv->clk); + + return ret; +} + +static void uniphier_sd_clk_disable(struct tmio_mmc_host *host) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + + reset_control_assert(priv->rst_br); + reset_control_assert(priv->rst); + clk_disable_unprepare(priv->clk); +} + +static void uniphier_sd_hw_reset(struct tmio_mmc_host *host) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + + reset_control_assert(priv->rst_hw); + /* For eMMC, minimum is 1us but give it 9us for good measure */ + udelay(9); + reset_control_deassert(priv->rst_hw); + /* For eMMC, minimum is 200us but give it 300us for good measure */ + usleep_range(300, 1000); +} + +static void uniphier_sd_set_clock(struct tmio_mmc_host *host, + unsigned int clock) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + unsigned long divisor; + u32 tmp; + + tmp = readl(host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); + + /* stop the clock before changing its rate to avoid a glitch signal */ + tmp &= ~CLK_CTL_SCLKEN; + writel(tmp, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); + + if (clock == 0) + return; + + tmp &= ~UNIPHIER_SD_CLK_CTL_DIV1024; + tmp &= ~UNIPHIER_SD_CLK_CTL_DIV1; + tmp &= ~CLK_CTL_DIV_MASK; + + divisor = priv->clk_rate / clock; + + /* + * In the original IP, bit[7:0] represents the divisor. + * bit7 set: 1/512, ... bit0 set:1/4, all bits clear: 1/2 + * + * The IP does not define a way to achieve 1/1. For UniPhier variants, + * bit10 is used for 1/1. Newer versions of UniPhier variants use + * bit16 for 1/1024. + */ + if (divisor <= 1) + tmp |= UNIPHIER_SD_CLK_CTL_DIV1; + else if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP && divisor > 512) + tmp |= UNIPHIER_SD_CLK_CTL_DIV1024; + else + tmp |= roundup_pow_of_two(divisor) >> 2; + + writel(tmp, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); + + tmp |= CLK_CTL_SCLKEN; + writel(tmp, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); +} + +static void uniphier_sd_host_init(struct tmio_mmc_host *host) +{ + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + u32 val; + + /* + * Connected to 32bit AXI. + * This register holds settings for SoC-specific internal bus + * connection. What is worse, the register spec was changed, + * breaking the backward compatibility. Write an appropriate + * value depending on a flag associated with a compatible string. + */ + if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) + val = 0x00000101; + else + val = 0x00000000; + + writel(val, host->ctl + UNIPHIER_SD_HOST_MODE); + + val = 0; + /* + * If supported, the controller can automatically + * enable/disable the clock line to the card. + */ + if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) + val |= UNIPHIER_SD_CLKCTL_OFFEN; + + writel(val, host->ctl + (CTL_SD_CARD_CLK_CTL << 1)); +} + +static int uniphier_sd_start_signal_voltage_switch(struct mmc_host *mmc, + struct mmc_ios *ios) +{ + struct tmio_mmc_host *host = mmc_priv(mmc); + struct uniphier_sd_priv *priv = uniphier_sd_priv(host); + struct pinctrl_state *pinstate; + u32 val, tmp; + + switch (ios->signal_voltage) { + case MMC_SIGNAL_VOLTAGE_330: + val = UNIPHIER_SD_VOLT_330; + pinstate = priv->pinstate_default; + break; + case MMC_SIGNAL_VOLTAGE_180: + val = UNIPHIER_SD_VOLT_180; + pinstate = priv->pinstate_uhs; + break; + default: + return -ENOTSUPP; + } + + tmp = readl(host->ctl + UNIPHIER_SD_VOLT); + tmp &= ~UNIPHIER_SD_VOLT_MASK; + tmp |= FIELD_PREP(UNIPHIER_SD_VOLT_MASK, val); + writel(tmp, host->ctl + UNIPHIER_SD_VOLT); + + pinctrl_select_state(priv->pinctrl, pinstate); + + return 0; +} + +static int uniphier_sd_uhs_init(struct tmio_mmc_host *host, + struct uniphier_sd_priv *priv) +{ + priv->pinctrl = devm_pinctrl_get(mmc_dev(host->mmc)); + if (IS_ERR(priv->pinctrl)) + return PTR_ERR(priv->pinctrl); + + priv->pinstate_default = pinctrl_lookup_state(priv->pinctrl, + PINCTRL_STATE_DEFAULT); + if (IS_ERR(priv->pinstate_default)) + return PTR_ERR(priv->pinstate_default); + + priv->pinstate_uhs = pinctrl_lookup_state(priv->pinctrl, "uhs"); + if (IS_ERR(priv->pinstate_uhs)) + return PTR_ERR(priv->pinstate_uhs); + + host->ops.start_signal_voltage_switch = + uniphier_sd_start_signal_voltage_switch; + + return 0; +} + +static int uniphier_sd_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct uniphier_sd_priv *priv; + struct tmio_mmc_data *tmio_data; + struct tmio_mmc_host *host; + int irq, ret; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "failed to get IRQ number"); + return irq; + } + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->caps = (unsigned long)of_device_get_match_data(dev); + + priv->clk = devm_clk_get(dev, NULL); + if (IS_ERR(priv->clk)) { + dev_err(dev, "failed to get clock\n"); + return PTR_ERR(priv->clk); + } + + priv->rst = devm_reset_control_get_shared(dev, "host"); + if (IS_ERR(priv->rst)) { + dev_err(dev, "failed to get host reset\n"); + return PTR_ERR(priv->rst); + } + + /* old version has one more reset */ + if (!(priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP)) { + priv->rst_br = devm_reset_control_get_shared(dev, "bridge"); + if (IS_ERR(priv->rst_br)) { + dev_err(dev, "failed to get bridge reset\n"); + return PTR_ERR(priv->rst_br); + } + } + + tmio_data = &priv->tmio_data; + tmio_data->flags |= TMIO_MMC_32BIT_DATA_PORT; + + host = tmio_mmc_host_alloc(pdev, tmio_data); + if (IS_ERR(host)) + return PTR_ERR(host); + + if (host->mmc->caps & MMC_CAP_HW_RESET) { + priv->rst_hw = devm_reset_control_get_exclusive(dev, "hw"); + if (IS_ERR(priv->rst_hw)) { + dev_err(dev, "failed to get hw reset\n"); + ret = PTR_ERR(priv->rst_hw); + goto free_host; + } + host->hw_reset = uniphier_sd_hw_reset; + } + + if (host->mmc->caps & MMC_CAP_UHS) { + ret = uniphier_sd_uhs_init(host, priv); + if (ret) { + dev_warn(dev, + "failed to setup UHS (error %d). Disabling UHS.", + ret); + host->mmc->caps &= ~MMC_CAP_UHS; + } + } + + ret = devm_request_irq(dev, irq, tmio_mmc_irq, IRQF_SHARED, + dev_name(dev), host); + if (ret) + goto free_host; + + if (priv->caps & UNIPHIER_SD_CAP_EXTENDED_IP) + host->dma_ops = &uniphier_sd_internal_dma_ops; + else + host->dma_ops = &uniphier_sd_external_dma_ops; + + host->bus_shift = 1; + host->clk_enable = uniphier_sd_clk_enable; + host->clk_disable = uniphier_sd_clk_disable; + host->set_clock = uniphier_sd_set_clock; + + ret = uniphier_sd_clk_enable(host); + if (ret) + goto free_host; + + uniphier_sd_host_init(host); + + tmio_data->ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34; + if (host->mmc->caps & MMC_CAP_UHS) + tmio_data->ocr_mask |= MMC_VDD_165_195; + + tmio_data->max_segs = 1; + tmio_data->max_blk_count = U16_MAX; + + ret = tmio_mmc_host_probe(host); + if (ret) + goto free_host; + + return 0; + +free_host: + tmio_mmc_host_free(host); + + return ret; +} + +static int uniphier_sd_remove(struct platform_device *pdev) +{ + struct tmio_mmc_host *host = platform_get_drvdata(pdev); + + tmio_mmc_host_remove(host); + uniphier_sd_clk_disable(host); + + return 0; +} + +static const struct of_device_id uniphier_sd_match[] = { + { + .compatible = "socionext,uniphier-sd-v2.91", + }, + { + .compatible = "socionext,uniphier-sd-v3.1", + .data = (void *)(UNIPHIER_SD_CAP_EXTENDED_IP | + UNIPHIER_SD_CAP_BROKEN_DMA_RX), + }, + { + .compatible = "socionext,uniphier-sd-v3.1.1", + .data = (void *)UNIPHIER_SD_CAP_EXTENDED_IP, + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, uniphier_sd_match); + +static struct platform_driver uniphier_sd_driver = { + .probe = uniphier_sd_probe, + .remove = uniphier_sd_remove, + .driver = { + .name = "uniphier-sd", + .of_match_table = uniphier_sd_match, + }, +}; +module_platform_driver(uniphier_sd_driver); + +MODULE_AUTHOR("Masahiro Yamada "); +MODULE_DESCRIPTION("UniPhier SD/eMMC host controller driver"); +MODULE_LICENSE("GPL v2");