ARM: dts: bcm2837: Add Raspberry Pi 3 B+

The Raspberry Pi 3 B+ has the following major differences compared
to the model 3 B:
* Microchip LAN7515 (Gigabit Ethernet with integrated USB 2.0 HUB)
* Cypress CYW43455 (802.11n/ac and BT 4.2)

We need to add the USB LAN chip so the bootloader can add the MAC address.
This is necessary because there ain't an EEPROM or a valid OTP.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This commit is contained in:
Stefan Wahren 2018-04-21 13:28:37 +02:00 committed by Eric Anholt
parent 9db90175e0
commit 71c0cd2283
3 changed files with 136 additions and 0 deletions

View file

@ -75,6 +75,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2835-rpi-a-plus.dtb \
bcm2836-rpi-2-b.dtb \
bcm2837-rpi-3-b.dtb \
bcm2837-rpi-3-b-plus.dtb \
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
dtb-$(CONFIG_ARCH_BCM_5301X) += \

View file

@ -0,0 +1,108 @@
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2837.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-lan7515.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
model = "Raspberry Pi 3 Model B+";
chosen {
/* 8250 auxiliary UART instead of pl011 */
stdout-path = "serial1:115200n8";
};
memory {
reg = <0 0x40000000>;
};
leds {
act {
gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
};
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>;
};
};
&firmware {
expgpio: gpio {
compatible = "raspberrypi,firmware-gpio";
gpio-controller;
#gpio-cells = <2>;
gpio-line-names = "BT_ON",
"WL_ON",
"STATUS_LED",
"LAN_RUN",
"",
"CAM_GPIO0",
"CAM_GPIO1",
"";
status = "okay";
};
};
&hdmi {
hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
status = "okay";
};
/* SDHCI is used to control the SDIO for wireless */
&sdhci {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&emmc_gpio34>;
status = "okay";
bus-width = <4>;
non-removable;
mmc-pwrseq = <&wifi_pwrseq>;
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* SDHOST is used to drive the SD card */
&sdhost {
pinctrl-names = "default";
pinctrl-0 = <&sdhost_gpio48>;
status = "okay";
bus-width = <4>;
};
/* uart0 communicates with the BT module */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
bluetooth {
compatible = "brcm,bcm43438-bt";
max-speed = <2000000>;
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
};
};
/* uart1 is mapped to the pin header */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_gpio14>;
status = "okay";
};

View file

@ -0,0 +1,27 @@
// SPDX-License-Identifier: GPL-2.0
/ {
aliases {
ethernet0 = &ethernet;
};
};
&usb {
usb-port@1 {
compatible = "usb424,2514";
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
usb-port@1 {
compatible = "usb424,2514";
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
ethernet: ethernet@1 {
compatible = "usb424,7800";
reg = <1>;
};
};
};
};