clk: Fixup spacing in comments

- Remove spaces in front of TABs,
- Correct indentation for some CLK_* flag descriptions.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This commit is contained in:
Geert Uytterhoeven 2014-04-22 15:11:41 +02:00 committed by Mike Turquette
parent e07b2b59c9
commit 725b418b43

View file

@ -40,14 +40,14 @@ struct dentry;
* through the clk_* api.
*
* @prepare: Prepare the clock for enabling. This must not return until
* the clock is fully prepared, and it's safe to call clk_enable.
* This callback is intended to allow clock implementations to
* do any initialisation that may sleep. Called with
* prepare_lock held.
* the clock is fully prepared, and it's safe to call clk_enable.
* This callback is intended to allow clock implementations to
* do any initialisation that may sleep. Called with
* prepare_lock held.
*
* @unprepare: Release the clock from its prepared state. This will typically
* undo any work done in the @prepare callback. Called with
* prepare_lock held.
* undo any work done in the @prepare callback. Called with
* prepare_lock held.
*
* @is_prepared: Queries the hardware to determine if the clock is prepared.
* This function is allowed to sleep. Optional, if this op is not
@ -58,16 +58,16 @@ struct dentry;
* Called with prepare mutex held. This function may sleep.
*
* @enable: Enable the clock atomically. This must not return until the
* clock is generating a valid clock signal, usable by consumer
* devices. Called with enable_lock held. This function must not
* sleep.
* clock is generating a valid clock signal, usable by consumer
* devices. Called with enable_lock held. This function must not
* sleep.
*
* @disable: Disable the clock atomically. Called with enable_lock held.
* This function must not sleep.
* This function must not sleep.
*
* @is_enabled: Queries the hardware to determine if the clock is enabled.
* This function must not sleep. Optional, if this op is not
* set then the enable count will be used.
* This function must not sleep. Optional, if this op is not
* set then the enable count will be used.
*
* @disable_unused: Disable the clock atomically. Only called from
* clk_disable_unused for gate clocks with special needs.
@ -75,34 +75,34 @@ struct dentry;
* sleep.
*
* @recalc_rate Recalculate the rate of this clock, by querying hardware. The
* parent rate is an input parameter. It is up to the caller to
* ensure that the prepare_mutex is held across this call.
* Returns the calculated rate. Optional, but recommended - if
* this op is not set then clock rate will be initialized to 0.
* parent rate is an input parameter. It is up to the caller to
* ensure that the prepare_mutex is held across this call.
* Returns the calculated rate. Optional, but recommended - if
* this op is not set then clock rate will be initialized to 0.
*
* @round_rate: Given a target rate as input, returns the closest rate actually
* supported by the clock.
* supported by the clock.
*
* @determine_rate: Given a target rate as input, returns the closest rate
* actually supported by the clock, and optionally the parent clock
* that should be used to provide the clock rate.
*
* @get_parent: Queries the hardware to determine the parent of a clock. The
* return value is a u8 which specifies the index corresponding to
* the parent clock. This index can be applied to either the
* .parent_names or .parents arrays. In short, this function
* translates the parent value read from hardware into an array
* index. Currently only called when the clock is initialized by
* __clk_init. This callback is mandatory for clocks with
* multiple parents. It is optional (and unnecessary) for clocks
* with 0 or 1 parents.
* return value is a u8 which specifies the index corresponding to
* the parent clock. This index can be applied to either the
* .parent_names or .parents arrays. In short, this function
* translates the parent value read from hardware into an array
* index. Currently only called when the clock is initialized by
* __clk_init. This callback is mandatory for clocks with
* multiple parents. It is optional (and unnecessary) for clocks
* with 0 or 1 parents.
*
* @set_parent: Change the input source of this clock; for clocks with multiple
* possible parents specify a new parent by passing in the index
* as a u8 corresponding to the parent in either the .parent_names
* or .parents arrays. This function in affect translates an
* array index into the value programmed into the hardware.
* Returns 0 on success, -EERROR otherwise.
* possible parents specify a new parent by passing in the index
* as a u8 corresponding to the parent in either the .parent_names
* or .parents arrays. This function in affect translates an
* array index into the value programmed into the hardware.
* Returns 0 on success, -EERROR otherwise.
*
* @set_rate: Change the rate of this clock. The requested rate is specified
* by the second argument, which should typically be the return
@ -254,12 +254,12 @@ void of_fixed_clk_setup(struct device_node *np);
*
* Flags:
* CLK_GATE_SET_TO_DISABLE - by default this clock sets the bit at bit_idx to
* enable the clock. Setting this flag does the opposite: setting the bit
* disable the clock and clearing it enables the clock
* enable the clock. Setting this flag does the opposite: setting the bit
* disable the clock and clearing it enables the clock
* CLK_GATE_HIWORD_MASK - The gate settings are only in lower 16-bit
* of this register, and mask of gate bits are in higher 16-bit of this
* register. While setting the gate bits, higher 16-bit should also be
* updated to indicate changing gate bits.
* of this register, and mask of gate bits are in higher 16-bit of this
* register. While setting the gate bits, higher 16-bit should also be
* updated to indicate changing gate bits.
*/
struct clk_gate {
struct clk_hw hw;
@ -298,20 +298,20 @@ struct clk_div_table {
*
* Flags:
* CLK_DIVIDER_ONE_BASED - by default the divisor is the value read from the
* register plus one. If CLK_DIVIDER_ONE_BASED is set then the divider is
* the raw value read from the register, with the value of zero considered
* register plus one. If CLK_DIVIDER_ONE_BASED is set then the divider is
* the raw value read from the register, with the value of zero considered
* invalid, unless CLK_DIVIDER_ALLOW_ZERO is set.
* CLK_DIVIDER_POWER_OF_TWO - clock divisor is 2 raised to the value read from
* the hardware register
* the hardware register
* CLK_DIVIDER_ALLOW_ZERO - Allow zero divisors. For dividers which have
* CLK_DIVIDER_ONE_BASED set, it is possible to end up with a zero divisor.
* Some hardware implementations gracefully handle this case and allow a
* zero divisor by not modifying their input clock
* (divide by one / bypass).
* CLK_DIVIDER_HIWORD_MASK - The divider settings are only in lower 16-bit
* of this register, and mask of divider bits are in higher 16-bit of this
* register. While setting the divider bits, higher 16-bit should also be
* updated to indicate changing divider bits.
* of this register, and mask of divider bits are in higher 16-bit of this
* register. While setting the divider bits, higher 16-bit should also be
* updated to indicate changing divider bits.
* CLK_DIVIDER_ROUND_CLOSEST - Makes the best calculated divider to be rounded
* to the closest integer instead of the up one.
*/
@ -359,9 +359,9 @@ struct clk *clk_register_divider_table(struct device *dev, const char *name,
* CLK_MUX_INDEX_ONE - register index starts at 1, not 0
* CLK_MUX_INDEX_BIT - register index is a single bit (power of two)
* CLK_MUX_HIWORD_MASK - The mux settings are only in lower 16-bit of this
* register, and mask of mux bits are in higher 16-bit of this register.
* While setting the mux bits, higher 16-bit should also be updated to
* indicate changing mux bits.
* register, and mask of mux bits are in higher 16-bit of this register.
* While setting the mux bits, higher 16-bit should also be updated to
* indicate changing mux bits.
*/
struct clk_mux {
struct clk_hw hw;