From 78894adedd87ebe2af60148c773780022a151fbc Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 2 Nov 2020 00:22:40 +0100 Subject: [PATCH] ARM: dts: ux500: Add a device tree for Janice This adds a basic device tree for the Samsung GT-I9070 mobile phone also known as Janice. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/Makefile | 1 + .../arm/boot/dts/ste-ux500-samsung-janice.dts | 894 ++++++++++++++++++ 2 files changed, 895 insertions(+) create mode 100644 arch/arm/boot/dts/ste-ux500-samsung-janice.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..e86bb4a9d521 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1278,6 +1278,7 @@ dtb-$(CONFIG_ARCH_U8500) += \ ste-hrefv60plus-tvk.dtb \ ste-href520-tvk.dtb \ ste-ux500-samsung-golden.dtb \ + ste-ux500-samsung-janice.dtb \ ste-ux500-samsung-skomer.dtb dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ld4-ref.dtb \ diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts new file mode 100644 index 000000000000..31ee34e79fe1 --- /dev/null +++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts @@ -0,0 +1,894 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice. + */ + +/dts-v1/; +#include "ste-db8500.dtsi" +#include "ste-ab8500.dtsi" +#include "ste-dbx5x0-pinctrl.dtsi" +#include +#include +#include + +/ { + model = "Samsung Galaxy S Advance (GT-I9070)"; + compatible = "samsung,janice", "st-ericsson,u8500"; + + chosen { + stdout-path = &serial2; + }; + + /* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */ + ldo_3v3_reg: regulator-gpio-ldo-3v3 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VMEM_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>; + startup-delay-us = <5000>; // FIXME + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_ldo_en_default_mode>; + }; + + /* + * External Ricoh "TSP" regulator for the touchscreen. + * One GPIO line controls two voltages of 3.3V and 1.8V + * this line is known as "TSP_LDO_ON1" in the schematics. + */ + ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "LDO_TSP_A3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* GPIO94 controls this regulator */ + gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_ldo_en_default_mode>; + }; + ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_TSP_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO94 controls this regulator */ + gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_ldo_en_default_mode>; + }; + + /* + * External Ricoh "TSP" regulator for the touchkeys. + * Two GPIO lines controls two voltages of 3.3V and 1.8V + * TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8 + * EN_LED_LDO controls VREG_KLED_3V3 (key LED) + */ + ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_KLED_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* GPIO68 controls this regulator */ + gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_led_ldo_default_mode>; + }; + ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_TOUCHKEY_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO89 controls this regulator */ + gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_ldo_on2_default_mode>; + }; + + + /* + * External Ricoh RP152L010B-TR LCD LDO regulator for the display. + * LCD_PWR_EN controls a 3.0V and 1.8V output. + */ + lcd_3v0_reg: regulator-gpio-lcd-3v0 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_LCD_3V0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + /* GPIO219 controls this regulator */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pwr_en_default_mode>; + }; + lcd_1v8_reg: regulator-gpio-lcd-1v8 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_LCD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO219 controls this regulator */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pwr_en_default_mode>; + }; + + /* + * This regulator is a GPIO line that drives the Broadcom WLAN + * line BT_VREG_EN high and enables the internal regulators + * inside the chip. + * + * The voltage specified here is only used to determine the OCR mask, + * the for the SDIO connector, the chip is actually connected + * directly to VBAT. + */ + wl_bt_reg: regulator-gpio-wlan { + compatible = "regulator-fixed"; + regulator-name = "BT_VREG_EN"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + startup-delay-us = <100000>; + /* GPIO222 (BT_VREG_EN) */ + gpio = <&gpio6 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_ldo_en_default>; + }; + + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default_mode>; + + button-home { + linux,code = ; + label = "HOME"; + /* GPIO91 */ + gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; + }; + button-volup { + linux,code = ; + label = "VOL+"; + /* GPIO67 */ + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + }; + button-voldown { + linux,code = ; + label = "VOL-"; + /* GPIO92 */ + gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; + }; + }; + + /* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */ + i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_0_default>; + #address-cells = <1>; + #size-cells = <0>; + + /* Yamaha YAS530 magnetometer */ + magnetometer@2e { + compatible = "yamaha,yas530"; + reg = <0x2e>; + /* VDD 3V */ + vdd-supply = <&ab8500_ldo_aux1_reg>; + /* IOVDD 1.8V */ + iovdd-supply = <&ab8500_ldo_aux2_reg>; + /* GPIO204 COMPASS_RST_N */ + reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&yas529_default>; + }; + /* TODO: this should also be used by the NCP6914 Camera power management unit */ + }; + + /* + * These pins do have an spi controller, however the controller on + * these pins is not the fully featured PL022 SSP/SPI block but the + * ST Micro diet "PL023" version. One of the lacking features in + * this derivative is 3wire support, so it cannot be used to drive + * this panel interface. We have to use GPIO bit-banging instead. + */ + spi-gpio-0 { + compatible = "spi-gpio"; + /* Clock on GPIO220 */ + sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>; + /* MISO/MOSI on GPIO224 (no separate MISO pin) */ + mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; + /* Chip select on GPIO223 */ + cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>; + num-chipselects = <1>; + + pinctrl-names = "default"; + pinctrl-0 = <&spi_gpio_0_default>; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6e63m0"; + reg = <0>; + vdd3-supply = <&lcd_3v0_reg>; + vci-supply = <&lcd_1v8_reg>; + /* Reset on GPIO139 */ + reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&panel_default_mode>; + spi-3wire; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + }; + + /* + * Current sense amplifier on the light sensor to convert current to + * voltage. We do not know if this is the actual configuration. The + * sense resistor value was found by calibrating in a room ambient + * light with a second mobile phone light sensor as reference. If you + * pry a Janice phone apart and inspect it you may figure this out. + */ + gp2a_shunt: current-sense-shunt { + compatible = "current-sense-shunt"; + io-channels = <&gpadc 0x07>; + shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */ + #io-channel-cells = <0>; + io-channel-ranges; + }; + + /* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */ + i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_1_default>; + #address-cells = <1>; + #size-cells = <0>; + + touchkey@20 { + compatible = "coreriver,tc360-touchkey"; + reg = <0x20>; + vdd-supply = <&ldo_kled_3v3_reg>; + vcc-supply = <&ldo_touchkey_1v8_reg>; + vddio-supply = <&ldo_touchkey_1v8_reg>; + + /* Interrupt on GPIO 198 */ + interrupt-parent = <&gpio6>; + interrupts = <6 IRQ_TYPE_EDGE_RISING>; + + pinctrl-names = "default"; + pinctrl-0 = <&touchkey_default_mode>; + linux,keycodes = ; + }; + }; + + /* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */ + i2c-gpio-2 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_2_default>; + #address-cells = <1>; + #size-cells = <0>; + /* TODO: add the Immersion ISA1200 I2C device here */ + }; + + /* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */ + i2c-gpio-3 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_3_default>; + #address-cells = <1>; + #size-cells = <0>; + + nfc@30 { + compatible = "nxp,pn547", "nxp,nxp-nci-i2c"; + reg = <0x30>; + /* NFC IRQ on GPIO32 */ + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + /* GPIO 31 */ + firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + /* GPIO88 */ + enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pn547_janice_default>; + }; + }; + + soc { + /* External Micro SD slot */ + sdi0_per1@80126000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <50000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + st,sig-dir-cmd; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-pin-fbclk; + full-pwr-cycle; + /* MMC is powered by AUX3 1.2V .. 2.91V */ + vmmc-supply = <&ab8500_ldo_aux3_reg>; + /* 2.9 V level translator is using AUX3 at 2.9 V as well */ + vqmmc-supply = <&ab8500_ldo_aux3_reg>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc0_a_2_default>; + pinctrl-1 = <&mc0_a_2_sleep>; + cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217 + status = "okay"; + }; + + /* WLAN SDIO channel */ + sdi1_per2@80118000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <50000000>; + bus-width = <4>; + non-removable; + cap-sd-highspeed; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc1_a_2_default>; + pinctrl-1 = <&mc1_a_2_sleep>; + /* + * GPIO-controlled voltage enablement: this drives + * the BT_VREG_EN line high when we use this device. + * Represented as regulator to fill OCR mask and to + * be usable in parallel with the Bluetooth chip. + */ + vmmc-supply = <&wl_bt_reg>; + + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + wifi@1 { + /* Actually BRCM4330 */ + compatible = "brcm,bcm4329-fmac"; + reg = <1>; + /* GPIO216 WL_HOST_WAKE */ + interrupt-parent = <&gpio6>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "host-wake"; + /* GPIO215 WLAN_RST_N */ + /* FIXME: kernel does not use this assert/deassert */ + reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_default_mode>; + }; + }; + + /* eMMC */ + sdi2_per3@80005000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <50000000>; + bus-width = <8>; + non-removable; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&ldo_3v3_reg>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc2_a_1_default>; + pinctrl-1 = <&mc2_a_1_sleep>; + status = "okay"; + }; + + /* GBF (Bluetooth) UART */ + uart@80120000 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&u0_a_1_default>; + pinctrl-1 = <&u0_a_1_sleep>; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + /* + * We actually have shutdown-gpios, BT_VREG_EN on GPIO222, + * but since this GPIO is shared with the WLAN chip, we need + * to reference the regulator instead. The regulator + * framework will reference count the GPIO usage and + * make sure we can use the same GPIO for several supplies. + */ + // shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; + vbat-supply = <&wl_bt_reg>; + /* BT_WAKE on GPIO199 */ + device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; + /* BT_HOST_WAKE on GPIO97 */ + /* FIXME: convert to interrupt */ + host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; + /* BT_RST_N on GPIO209 */ + reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&bluetooth_default_mode>; + }; + }; + + /* GPS UART */ + uart@80121000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + /* CTS/RTS is not used, CTS is repurposed as GPIO */ + pinctrl-0 = <&u1rxtx_a_1_default>; + pinctrl-1 = <&u1rxtx_a_1_sleep>; + /* FIXME: add a device for the GPS here */ + }; + + /* Debugging console UART connected to TSU6111RSVR (FSA880) */ + uart@80007000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&u2rxtx_c_1_default>; + pinctrl-1 = <&u2rxtx_c_1_sleep>; + }; + + prcmu@80157000 { + ab8500 { + ab8500_usb { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&usb_a_1_default>; + pinctrl-1 = <&usb_a_1_sleep>; + }; + + ab8500-regulators { + ab8500_ldo_aux1 { + /* Used for VDD for sensors */ + regulator-name = "V-SENSORS-VDD"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ab8500_ldo_aux2 { + /* Used for VIO for sensors */ + regulator-name = "V-SENSORS-VIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ab8500_ldo_aux3 { + /* Used for voltage for external MMC/SD card */ + regulator-name = "V-MMC-SD"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2910000>; + }; + }; + }; + }; + + /* I2C0 */ + i2c@80004000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c0_a_1_default>; + pinctrl-1 = <&i2c0_a_1_sleep>; + + proximity@44 { + /* Janice has the GP2AP002A00F with light sensor */ + compatible = "sharp,gp2ap002a00f"; + clock-frequency = <400000>; + reg = <0x44>; + + interrupt-parent = <&gpio4>; + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vio-supply = <&ab8500_ldo_aux2_reg>; + /* ADC channel AUX2 to read ALSOUT ambient light sensor out */ + io-channels = <&gp2a_shunt>; + io-channel-names = "alsout"; + pinctrl-names = "default"; + pinctrl-0 = <&gp2ap002_janice_default>; + /* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */ + sharp,proximity-far-hysteresis = /bits/ 8 <0x40>; + sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>; + }; + }; + + /* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */ + i2c@80122000 { + status = "okay"; + pinctrl-names = "default","sleep"; + pinctrl-0 = <&i2c1_b_2_default>; + pinctrl-1 = <&i2c1_b_2_sleep>; + + /* Texas Instruments TSU6111 micro USB switch */ + usb-switch@25 { + compatible = "ti,tsu6111"; + reg = <0x25>; + /* Interrupt JACK_INT_N on GPIO95 */ + interrupt-parent = <&gpio2>; + interrupts = <31 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&tsu6111_janice_default>; + }; + }; + + /* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */ + i2c@80128000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_b_2_default>; + pinctrl-1 = <&i2c2_b_2_sleep>; + + gyroscope@68 { + compatible = "invensense,mpu3050"; + reg = <0x68>; + /* GPIO226 interrupt */ + interrupt-parent = <&gpio7>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + /* FIXME: no idea about this */ + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "1"; + vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V + vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V + pinctrl-names = "default"; + pinctrl-0 = <&mpu3050_janice_default>; + + /* + * The MPU-3050 acts as a hub for the + * accelerometer. + */ + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + /* Bosch BMA222 accelerometer */ + accelerometer@08 { + compatible = "bosch,bma222"; + reg = <0x08>; + /* FIXME: no idea about this */ + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "1"; + vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V + vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V + }; + }; + }; + }; + + /* I2C3 */ + i2c@80110000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c3_c_2_default>; + pinctrl-1 = <&i2c3_c_2_sleep>; + + /* Atmel mXT224E touchscreen */ + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + /* GPIO218 (TSP_INT_1V8) */ + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + /* VDDA is "analog supply", 2.57-3.47 V */ + vdda-supply = <&ldo_tsp_3v3_reg>; + /* VDD is "digital supply" 1.71-3.47V */ + vdd-supply = <&ldo_tsp_1v8_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_default>; + }; + }; + + mcde@a0350000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dpi_default_mode>; + + port { + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; +}; + +&pinctrl { + /* + * This extends the MC0_A_2 default config to include + * the card detect GPIO217 line. + */ + sdi0 { + mc0_a_2_default { + default_cfg4 { + pins = "GPIO217_AH12"; /* card detect */ + ste,config = <&gpio_in_pd>; + }; + }; + }; + mcde { + dpi_default_mode: dpi_default { + default_mux1 { + /* Mux in all the data lines */ + function = "lcd"; + groups = + /* Data lines D0-D7 GPIO70..GPIO77 */ + "lcd_d0_d7_a_1", + /* Data lines D8-D11 GPIO78..GPIO81 */ + "lcd_d8_d11_a_1", + /* Data lines D12-D15 GPIO82..GPIO85 */ + "lcd_d12_d15_a_1", + /* Data lines D16-D23 GPIO161..GPIO168 */ + "lcd_d16_d23_b_1"; + }; + default_mux2 { + function = "lcda"; + /* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */ + groups = "lcdaclk_b_1", "lcda_b_1"; + }; + /* Input, no pull-up is the default state for pins used for an alt function */ + default_cfg1 { + pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23"; + ste,config = <&in_nopull>; + }; + }; + }; + /* GPIO for panel reset control */ + panel { + panel_default_mode: panel_default { + janice_cfg1 { + /* Reset line */ + pins = "GPIO139_C9"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the eMMC */ + emmc-ldo { + emmc_ldo_en_default_mode: emmc_ldo_default { + /* LDO enable on GPIO6 */ + janice_cfg1 { + pins = "GPIO6_AF6"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the touchscreen */ + tsp-ldo { + tsp_ldo_en_default_mode: tsp_ldo_default { + /* LDO enable on GPIO94 */ + janice_cfg1 { + pins = "GPIO94_D7"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the key LED */ + key-led { + en_led_ldo_default_mode: en_led_ldo_default { + /* EN_LED_LDO on GPIO68 */ + janice_cfg1 { + pins = "GPIO68_E1"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the touchkeys */ + touchkey-ldo { + tsp_ldo_on2_default_mode: tsp_ldo_on2_default { + /* TSP_LDO_ON2 on GPIO89 */ + janice_cfg1 { + pins = "GPIO89_E6"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + touchkey { + touchkey_default_mode: touchkey_default { + janice_cfg1 { + /* Interrupt */ + pins = "GPIO198_AG25"; + ste,config = <&gpio_in_nopull>; + }; + janice_cfg2 { + /* Reset, actually completely unused (not routed) */ + pins = "GPIO205_AG23"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + /* GPIO that enabled the LDO regulator for the LCD display */ + lcd-ldo { + lcd_pwr_en_default_mode: lcd_pwr_en_default { + /* LCD_PWR_EN on GPIO219 */ + janice_cfg1 { + pins = "GPIO219_AG10"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the WLAN internal LDO regulators */ + wlan-ldo { + wlan_ldo_en_default: wlan_ldo_default { + /* GPIO222 BT_VREG_ON */ + janice_cfg1 { + pins = "GPIO222_AJ9"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + /* GPIO keys */ + gpio-keys { + gpio_keys_default_mode: gpio_keys_default { + skomer_cfg1 { + pins = "GPIO67_G2", /* VOL UP */ + "GPIO91_B6", /* HOME */ + "GPIO92_D6"; /* VOL DOWN */ + ste,config = <&gpio_in_pu>; + }; + }; + }; + /* Interrupt line for the Atmel MXT228 touchscreen */ + tsp { + tsp_default: tsp_default { + janice_cfg1 { + pins = "GPIO218_AH11"; /* TSP_INT_1V8 */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* Reset line for the Yamaha YAS529 magnetometer */ + yas529 { + yas529_default: yas529_janice { + janice_cfg1 { + pins = "GPIO204_AF23"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* Interrupt line for light/proximity sensor GP2AP002 */ + gp2ap002 { + gp2ap002_janice_default: gp2ap002_janice { + janice_cfg1 { + pins = "GPIO146_D13"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* Interrupt line for Invensense MPU3050 gyroscope */ + mpu3050 { + mpu3050_janice_default: mpu3050_janice { + janice_cfg1 { + /* GPIO226 used for IRQ */ + pins = "GPIO226_AF8"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for magnetometer and NCP6914 */ + i2c-gpio-0 { + i2c_gpio_0_default: i2c_gpio_0 { + janice_cfg1 { + pins = "GPIO143_D12", "GPIO144_B13"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for the Cypress touchkeys */ + i2c-gpio-1 { + i2c_gpio_1_default: i2c_gpio_1 { + janice_cfg1 { + pins = "GPIO196_AG26", "GPIO197_AH24"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for the Immersion ISA1200 */ + i2c-gpio-2 { + i2c_gpio_2_default: i2c_gpio_2 { + janice_cfg1 { + pins = "GPIO201_AF24", "GPIO202_AF25"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for the NFC */ + i2c-gpio-3 { + i2c_gpio_3_default: i2c_gpio_3 { + janice_cfg1 { + pins = "GPIO151_D17", "GPIO152_D16"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based SPI bus for the display */ + spi-gpio-0 { + spi_gpio_0_default: spi_gpio_0 { + janice_cfg1 { + pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9"; + ste,config = <&gpio_out_hi>; + }; + /* This pin is unused but belongs with this SPI block */ + janice_cfg2 { + pins = "GPIO225_AG8"; + ste,config = <&in_pd>; + }; + }; + }; + wlan { + wlan_default_mode: wlan_default { + /* GPIO215 used for RESET_N */ + janice_cfg1 { + pins = "GPIO215_AH13"; + ste,config = <&gpio_out_lo>; + }; + /* GPIO216 for WL_HOST_WAKE */ + janice_cfg2 { + pins = "GPIO216_AG12"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + bluetooth { + bluetooth_default_mode: bluetooth_default { + janice_cfg1 { + pins = "GPIO199_AH23"; + ste,config = <&gpio_out_lo>; + }; + janice_cfg2 { + pins = "GPIO97_D9"; + ste,config = <&gpio_in_nopull>; + }; + janice_cfg3 { + pins = "GPIO209_AG15"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* Interrupt line for TI TSU6111 Micro USB switch */ + tsu6111 { + tsu6111_janice_default: tsu6111_janice { + janice_cfg1 { + /* GPIO95 used for IRQ */ + pins = "GPIO95_E8"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + nfc { + pn547_janice_default: pn547_janice { + /* Interrupt line */ + janice_cfg1 { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_nopull>; + }; + /* Enable and firmware GPIOs */ + janice_cfg2 { + pins = "GPIO31_V3", "GPIO88_C4"; + ste,config = <&gpio_out_lo>; + }; + }; + }; +};