serverworks: PIO mode setup fixes

* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
  timings being programmed and possibly the data corruption (it seems that
  the minimum possible values were used but I lack the datasheets to be sure)

* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
  when doing PIO autotuning (pio == 255)

* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
  return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
  takes care of PIO tuning if no suitable DMA mode is found)

* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
  config_chipset_for_pio() contained numerous bugs when selecting PIO mode
  (luckily it was only used for devices limited to PIO by capabilities/BIOS):

  - it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
    before using them

  - it tried to found out maximum PIO mode basing on minimum IORDY cycle time
    (moreover wrong cycle times were used for PIO0/1/5)

  - it was overriding PIO blacklist and conservative PIO "downgrade" done
    by ide_get_best_pio_mode()

  - if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
    (XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
     was the same as if using XFER_PIO_5 => wrong PIO timings were set)

  - it was overriding drive->current_speed

* bump driver version

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This commit is contained in:
Bartlomiej Zolnierkiewicz 2007-05-16 00:51:42 +02:00
parent 4fce3164b8
commit 9445de76c1

View file

@ -1,9 +1,10 @@
/*
* linux/drivers/ide/pci/serverworks.c Version 0.8 25 Ebr 2003
* linux/drivers/ide/pci/serverworks.c Version 0.9 Mar 4 2007
*
* Copyright (C) 1998-2000 Michel Aubry
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
* Portions copyright (c) 2001 Sun Microsystems
*
*
@ -136,19 +137,14 @@ static int svwks_tune_chipset (ide_drive_t *drive, u8 xferspeed)
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
u8 speed;
u8 pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
u8 speed = ide_rate_filter(drive, xferspeed);
u8 pio = ide_get_best_pio_mode(drive, 255, 4, NULL);
u8 unit = (drive->select.b.unit & 0x01);
u8 csb5 = svwks_csb_check(dev);
u8 ultra_enable = 0, ultra_timing = 0;
u8 dma_timing = 0, pio_timing = 0;
u16 csb5_pio = 0;
if (xferspeed == 255) /* PIO auto-tuning */
speed = XFER_PIO_0 + pio;
else
speed = ide_rate_filter(drive, xferspeed);
/* If we are about to put a disk into UDMA mode we screwed up.
Our code assumes we never _ever_ do this on an OSB4 */
@ -231,6 +227,9 @@ static int svwks_tune_chipset (ide_drive_t *drive, u8 xferspeed)
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
/*
* TODO: always setup PIO mode so this won't be needed
*/
pio_timing |= pio_modes[pio];
csb5_pio |= (pio << (4*drive->dn));
dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
@ -242,6 +241,9 @@ static int svwks_tune_chipset (ide_drive_t *drive, u8 xferspeed)
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
/*
* TODO: always setup PIO mode so this won't be needed
*/
pio_timing |= pio_modes[pio];
csb5_pio |= (pio << (4*drive->dn));
dma_timing |= dma_modes[2];
@ -262,58 +264,18 @@ static int svwks_tune_chipset (ide_drive_t *drive, u8 xferspeed)
return (ide_config_drive_speed(drive, speed));
}
static void config_chipset_for_pio (ide_drive_t *drive)
{
u16 eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
u16 xfer_pio = drive->id->eide_pio_modes;
u8 timing, speed, pio;
pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
if (xfer_pio > 4)
xfer_pio = 0;
if (drive->id->eide_pio_iordy > 0)
for (xfer_pio = 5;
xfer_pio>0 &&
drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
xfer_pio--);
else
xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
(drive->id->eide_pio_modes & 2) ? 0x04 :
(drive->id->eide_pio_modes & 1) ? 0x03 :
(drive->id->tPIO & 2) ? 0x02 :
(drive->id->tPIO & 1) ? 0x01 : xfer_pio;
timing = (xfer_pio >= pio) ? xfer_pio : pio;
switch(timing) {
case 4: speed = XFER_PIO_4;break;
case 3: speed = XFER_PIO_3;break;
case 2: speed = XFER_PIO_2;break;
case 1: speed = XFER_PIO_1;break;
default:
speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
break;
}
(void) svwks_tune_chipset(drive, speed);
drive->current_speed = speed;
}
static void svwks_tune_drive (ide_drive_t *drive, u8 pio)
{
if(pio == 255)
(void) svwks_tune_chipset(drive, 255);
else
(void) svwks_tune_chipset(drive, (XFER_PIO_0 + pio));
pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
(void)svwks_tune_chipset(drive, XFER_PIO_0 + pio);
}
static int config_chipset_for_dma (ide_drive_t *drive)
{
u8 speed = ide_max_dma_mode(drive);
if (!(speed))
speed = XFER_PIO_0 + ide_get_best_pio_mode(drive, 255, 5, NULL);
if (!speed)
return 0;
(void) svwks_tune_chipset(drive, speed);
return ide_dma_enable(drive);
@ -327,7 +289,7 @@ static int svwks_config_drive_xfer_rate (ide_drive_t *drive)
return 0;
if (ide_use_fast_pio(drive))
config_chipset_for_pio(drive);
svwks_tune_drive(drive, 255);
return -1;
}