mirrors/linux-stable
1
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git synced 2024-10-12 03:26:26 +00:00
Code Issues Releases Wiki Activity

Amlogic DT changes for 64-bit platforms for v4.10

Browse source 
Support for new drivers:
 - USB
 - i2c
 - SPI
 - mailbox/MHU
 - PWM
 - ethernet MAC, PHY
 - secure monitor
 - IR
 - watchdog
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJYK5ljAAoJEFk3GJrT+8Zlm0wP/jAQ3dexIVIhuk6xwnYDnVSD
 dTRXQwvZcARzogbiMxK1sIqamDe/jZveAJg6Wd9KvlqmW76XP2Npyk3/d4SZXzFx
 S4Dj0g91XlUMhZP/50DRfMqQ9ylvcCtPSd6ITp7sUX4VMbVoZYpxTFUlg1askC4V
 0Rts7tqAYmWCHBfcRrUXG9M8p1NxaeljxqBRKD5gU2E5zh/A8TU+eUnJqDuyN8hR
 4OF19ceOsh/IVVKjwbQsTqHdGMvYCN9Fw26GA7mb40foOum4o5ET8IydNd37aAD5
 D8i67djmd2SYlCqOYG8B9V8PU4bIPOvAPvkY6/FB3QKKYcIzJvBmDaqyHUNQzP5K
 gqxqTcAZr/ERI7Wh122+MhjvL2cV0WUjHY5LVqkK0B2bluLJqC8aqUg2d9TftVAc
 +nmsfAZhKz5l77rL4dHIfo9EPNDI5tzTGyxgyU8DsogTmHiEVGHnUF2ekORwls3q
 wbBVDr2RIB4ucEF3eFmJYjNBIKLNebLtirYRjDbtIQofvR6ZxjRcra8YopNnkVaU
 0hlghavZhTXF0UQvm3D2ySfaaZg94LpKiG3XLvj4+4hNsdTH5/KsxNbNm2MYRssZ
 fFYV0P2Aymp0nO/sDpomVZDGZiqF7WS4Txj51/892ogC4E1ZrtMnW56RCQ52p5Ns
 OnMHREDpNUg/zTFW5ka2
 =32ah
 -----END PGP SIGNATURE-----

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt64

Amlogic DT changes for 64-bit platforms for v4.10

Support for new drivers:
- USB
- i2c
- SPI
- mailbox/MHU
- PWM
- ethernet MAC, PHY
- secure monitor
- IR
- watchdog

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (27 commits)
  ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes
  ARM64: dts: meson-gxl-s905x: Enable internal ethernet PHY
  ARM64: dts: meson-gxl-p23x: Enable ethernet
  ARM64: dts: meson-gxl: Add ethernet nodes with internal PHY
  ARM64: dts: amlogic: Reorder copyrights for meson-gx
  ARM64: dts: meson-gxl-p23x: Enable IR receiver
  ARM64: dts: meson-gxl-p23x: Add SD/SDIO/MMC and PWM nodes
  ARM64: dts: meson-gxl-p23x: Add uart pinctrl
  ARM64: dts: meson-gxl: Add MMC/SD/SDIO nodes
  ARM64: dts: meson-gxl: Add i2c nodes
  ARM64: dts: meson-gxl: Add clock nodes
  ARM64: dts: meson-gxl: Add pinctrl nodes
  ARM64: dts: meson-gxbb: Move common nodes to meson-gx
  ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes
  ARM64: dts: meson-gxbb: Add SRAM node
  ARM64: dts: meson-gxbb: Add MMC nodes to Nexbox A95x
  ARM64: dts: meson-gxbb: Add P20x Wifi SDIO support
  ARM64: dts: meson-gxbb: Add Wifi 32K clock for p20x boards
  ARM64: dts: meson-gxbb: add MMC support
  ARM64: dts: meson-gxbb-odroidc2: Enable USB Nodes
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>
This commit is contained in:
Olof Johansson 2016-11-18 16:50:59 -08:00
commit adc8f25f63
16 changed files with 2148 additions and 562 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

11
Documentation/devicetree/bindings/arm/amlogic.txt
View file

@ -17,6 +17,14 @@ Boards with the Amlogic Meson GXBaby SoC shall have the following properties:
Required root node property:
compatible: "amlogic,meson-gxbb";
Boards with the Amlogic Meson GXL S905X SoC shall have the following properties:
Required root node property:
compatible: "amlogic,s905x", "amlogic,meson-gxl";
Boards with the Amlogic Meson GXL S905D SoC shall have the following properties:
Required root node property:
compatible: "amlogic,s905d", "amlogic,meson-gxl";
Board compatible values:
- "geniatech,atv1200" (Meson6)
- "minix,neo-x8" (Meson8)
@ -28,3 +36,6 @@ Board compatible values:
- "hardkernel,odroid-c2" (Meson gxbb)
- "amlogic,p200" (Meson gxbb)
- "amlogic,p201" (Meson gxbb)
- "amlogic,p212" (Meson gxl s905x)
- "amlogic,p230" (Meson gxl s905d)
- "amlogic,p231" (Meson gxl s905d)

1
Documentation/devicetree/bindings/vendor-prefixes.txt
View file

@ -186,6 +186,7 @@ neonode Neonode Inc.
netgear NETGEAR
netlogic Broadcom Corporation (formerly NetLogic Microsystems)
netxeon Shenzhen Netxeon Technology CO., LTD
nexbox Nexbox
newhaven Newhaven Display International
nintendo Nintendo
nokia Nokia

4
arch/arm64/boot/dts/amlogic/Makefile
View file

@ -1,9 +1,13 @@
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-p200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-p201.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)

360
arch/arm64/boot/dts/amlogic/meson-gx.dtsi Normal file
View file

@ -0,0 +1,360 @@
/*
* Copyright (c) 2016 Andreas Färber
*
* Copyright (c) 2016 BayLibre, SAS.
* Author: Neil Armstrong <narmstrong@baylibre.com>
*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
interrupt-parent = <&gic>;
#address-cells = <2>;
#size-cells = <2>;
cpus {
#address-cells = <0x2>;
#size-cells = <0x0>;
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&l2>;
};
cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x1>;
enable-method = "psci";
next-level-cache = <&l2>;
};
cpu2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x2>;
enable-method = "psci";
next-level-cache = <&l2>;
};
cpu3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x3>;
enable-method = "psci";
next-level-cache = <&l2>;
};
l2: l2-cache0 {
compatible = "cache";
};
};
arm-pmu {
compatible = "arm,cortex-a53-pmu";
interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
};
psci {
compatible = "arm,psci-0.2";
method = "smc";
};
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
};
xtal: xtal-clk {
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "xtal";
#clock-cells = <0>;
};
firmware {
sm: secure-monitor {
compatible = "amlogic,meson-gx-sm", "amlogic,meson-gxbb-sm";
};
};
efuse: efuse {
compatible = "amlogic,meson-gx-efuse", "amlogic,meson-gxbb-efuse";
#address-cells = <1>;
#size-cells = <1>;
sn: sn@14 {
reg = <0x14 0x10>;
};
eth_mac: eth_mac@34 {
reg = <0x34 0x10>;
};
bid: bid@46 {
reg = <0x46 0x30>;
};
};
soc {
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
ranges;
cbus: cbus@c1100000 {
compatible = "simple-bus";
reg = <0x0 0xc1100000 0x0 0x100000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
reset: reset-controller@4404 {
compatible = "amlogic,meson-gx-reset", "amlogic,meson-gxbb-reset";
reg = <0x0 0x04404 0x0 0x20>;
#reset-cells = <1>;
};
uart_A: serial@84c0 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x84c0 0x0 0x14>;
interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
uart_B: serial@84dc {
compatible = "amlogic,meson-uart";
reg = <0x0 0x84dc 0x0 0x14>;
interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
i2c_A: i2c@8500 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x08500 0x0 0x20>;
interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
pwm_ab: pwm@8550 {
compatible = "amlogic,meson-gx-pwm", "amlogic,meson-gxbb-pwm";
reg = <0x0 0x08550 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
pwm_cd: pwm@8650 {
compatible = "amlogic,meson-gx-pwm", "amlogic,meson-gxbb-pwm";
reg = <0x0 0x08650 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
pwm_ef: pwm@86c0 {
compatible = "amlogic,meson-gx-pwm", "amlogic,meson-gxbb-pwm";
reg = <0x0 0x086c0 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
uart_C: serial@8700 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x8700 0x0 0x14>;
interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
i2c_B: i2c@87c0 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087c0 0x0 0x20>;
interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c_C: i2c@87e0 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087e0 0x0 0x20>;
interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
watchdog@98d0 {
compatible = "amlogic,meson-gx-wdt", "amlogic,meson-gxbb-wdt";
reg = <0x0 0x098d0 0x0 0x10>;
clocks = <&xtal>;
};
};
gic: interrupt-controller@c4301000 {
compatible = "arm,gic-400";
reg = <0x0 0xc4301000 0 0x1000>,
<0x0 0xc4302000 0 0x2000>,
<0x0 0xc4304000 0 0x2000>,
<0x0 0xc4306000 0 0x2000>;
interrupt-controller;
interrupts = <GIC_PPI 9
(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
#interrupt-cells = <3>;
#address-cells = <0>;
};
aobus: aobus@c8100000 {
compatible = "simple-bus";
reg = <0x0 0xc8100000 0x0 0x100000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
uart_AO: serial@4c0 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x004c0 0x0 0x14>;
interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
ir: ir@580 {
compatible = "amlogic,meson-gxbb-ir";
reg = <0x0 0x00580 0x0 0x40>;
interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
};
periphs: periphs@c8834000 {
compatible = "simple-bus";
reg = <0x0 0xc8834000 0x0 0x2000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
rng {
compatible = "amlogic,meson-rng";
reg = <0x0 0x0 0x0 0x4>;
};
};
hiubus: hiubus@c883c000 {
compatible = "simple-bus";
reg = <0x0 0xc883c000 0x0 0x2000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
mailbox: mailbox@404 {
compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
reg = <0 0x404 0 0x4c>;
interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
<0 209 IRQ_TYPE_EDGE_RISING>,
<0 210 IRQ_TYPE_EDGE_RISING>;
#mbox-cells = <1>;
};
};
ethmac: ethernet@c9410000 {
compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
reg = <0x0 0xc9410000 0x0 0x10000
0x0 0xc8834540 0x0 0x4>;
interrupts = <0 8 1>;
interrupt-names = "macirq";
phy-mode = "rgmii";
status = "disabled";
};
apb: apb@d0000000 {
compatible = "simple-bus";
reg = <0x0 0xd0000000 0x0 0x200000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
sd_emmc_a: mmc@70000 {
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
reg = <0x0 0x70000 0x0 0x2000>;
interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
sd_emmc_b: mmc@72000 {
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
reg = <0x0 0x72000 0x0 0x2000>;
interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
sd_emmc_c: mmc@74000 {
compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
reg = <0x0 0x74000 0x0 0x2000>;
interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
};
};
};

231
arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts Normal file
View file

@ -0,0 +1,231 @@
/*
* Copyright (c) 2016 Andreas Färber
* Copyright (c) 2016 BayLibre, Inc.
* Author: Neil Armstrong <narmstrong@kernel.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "meson-gxbb.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "nexbox,a95x", "amlogic,meson-gxbb";
model = "NEXBOX A95X";
aliases {
serial0 = &uart_AO;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
};
leds {
compatible = "gpio-leds";
blue {
label = "a95x:system-status";
gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
button@0 {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
};
};
vddio_card: gpio-regulator {
compatible = "regulator-gpio";
regulator-name = "VDDIO_CARD";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
states = <1800000 0
3300000 1>;
};
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
};
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&ethmac {
status = "okay";
pinctrl-0 = <&eth_rmii_pins>;
pinctrl-names = "default";
phy-mode = "rmii";
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
/* Wireless SDIO Module */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
non-removable;
disable-wp;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-names = "default";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
cd-inverted;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_card>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
pinctrl-names = "default";
bus-width = <8>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vddio_boot>;
};
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};

119
arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
View file

@ -64,6 +64,18 @@ memory@0 {
reg = <0x0 0x0 0x0 0x80000000>;
};
usb_otg_pwr: regulator-usb-pwrs {
compatible = "regulator-fixed";
regulator-name = "USB_OTG_PWR";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
leds {
compatible = "gpio-leds";
blue {
@ -73,6 +85,56 @@ blue {
default-state = "off";
};
};
tflash_vdd: regulator-tflash_vdd {
/*
* signal name from schematics: TFLASH_VDD_EN
*/
compatible = "regulator-fixed";
regulator-name = "TFLASH_VDD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio_ao GPIOAO_12 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
tf_io: gpio-regulator-tf_io {
compatible = "regulator-gpio";
regulator-name = "TF_IO";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
/*
* signal name from schematics: TF_3V3N_1V8_EN
*/
gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
states = <3300000 0
1800000 1>;
};
vcc1v8: regulator-vcc1v8 {
compatible = "regulator-fixed";
regulator-name = "VCC1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vcc3v3: regulator-vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
};
&uart_AO {
@ -83,7 +145,7 @@ &uart_AO {
&ethmac {
status = "okay";
pinctrl-0 = <&eth_pins>;
pinctrl-0 = <&eth_rgmii_pins>;
pinctrl-names = "default";
};
@ -98,3 +160,58 @@ &i2c_A {
pinctrl-0 = <&i2c_a_pins>;
pinctrl-names = "default";
};
&usb0_phy {
status = "okay";
phy-supply = <&usb_otg_pwr>;
};
&usb1_phy {
status = "okay";
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};
/* SD */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-names = "default";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
cd-inverted;
vmmc-supply = <&tflash_vdd>;
vqmmc-supply = <&tf_io>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
pinctrl-names = "default";
bus-width = <8>;
cap-sd-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
cap-mmc-highspeed;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc3v3>;
vqmmc-supply = <&vcc1v8>;
};

129
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
View file

@ -70,6 +70,61 @@ usb_pwr: regulator-usb-pwrs {
gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vddio_card: gpio-regulator {
compatible = "regulator-gpio";
regulator-name = "VDDIO_CARD";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
states = <1800000 0
3300000 1>;
};
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
};
/* This UART is brought out to the DB9 connector */
@ -81,7 +136,7 @@ &uart_AO {
&ethmac {
status = "okay";
pinctrl-0 = <&eth_pins>;
pinctrl-0 = <&eth_rgmii_pins>;
pinctrl-names = "default";
};
@ -107,3 +162,75 @@ &usb0 {
&usb1 {
status = "okay";
};
/* Wireless SDIO Module */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
non-removable;
disable-wp;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
brcmf: bcrmf@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-names = "default";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
cd-inverted;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_card>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
pinctrl-names = "default";
bus-width = <8>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vddio_boot>;
};
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};

106
arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
View file

@ -65,6 +65,39 @@ usb_vbus: regulator-usb0-vbus {
enable-active-high;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vcc_1v8: regulator-vcc_1v8 {
compatible = "regulator-fixed";
regulator-name = "VCC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>,
<&gpio GPIOX_20 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
};
&uart_AO {
@ -82,7 +115,7 @@ &ir {
&ethmac {
status = "okay";
pinctrl-0 = <&eth_pins>;
pinctrl-0 = <&eth_rgmii_pins>;
pinctrl-names = "default";
};
@ -102,3 +135,74 @@ &usb0 {
&usb1 {
status = "okay";
};
/* Wireless SDIO Module */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins &sdio_irq_pins>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
non-removable;
disable-wp;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vcc_1v8>;
brcmf: bcrmf@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-names = "default";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
cd-inverted;
vmmc-supply = <&vcc_3v3>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
pinctrl-names = "default";
bus-width = <8>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vmmcq-sumpply = <&vcc_1v8>;
};
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};

956
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
View file

@ -40,9 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include "meson-gx.dtsi"
#include <dt-bindings/gpio/meson-gxbb-gpio.h>
#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
#include <dt-bindings/clock/gxbb-clkc.h>
@ -51,106 +49,30 @@
/ {
compatible = "amlogic,meson-gxbb";
interrupt-parent = <&gic>;
#address-cells = <2>;
#size-cells = <2>;
cpus {
#address-cells = <0x2>;
#size-cells = <0x0>;
scpi {
compatible = "amlogic,meson-gxbb-scpi";
mboxes = <&mailbox 1 &mailbox 2>;
shmem = <&cpu_scp_lpri &cpu_scp_hpri>;
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x0>;
enable-method = "psci";
clocks {
compatible = "arm,scpi-clocks";
scpi_dvfs: scpi_clocks@0 {
compatible = "arm,scpi-dvfs-clocks";
#clock-cells = <1>;
clock-indices = <0>;
clock-output-names = "vcpu";
};
};
cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x1>;
enable-method = "psci";
scpi_sensors: sensors {
compatible = "arm,scpi-sensors";
#thermal-sensor-cells = <1>;
};
cpu2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x2>;
enable-method = "psci";
};
cpu3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x0 0x3>;
enable-method = "psci";
};
};
arm-pmu {
compatible = "arm,cortex-a53-pmu";
interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
};
psci {
compatible = "arm,psci-0.2";
method = "smc";
};
firmware {
sm: secure-monitor {
compatible = "amlogic,meson-gxbb-sm";
};
};
efuse: efuse {
compatible = "amlogic,meson-gxbb-efuse";
#address-cells = <1>;
#size-cells = <1>;
sn: sn@14 {
reg = <0x14 0x10>;
};
eth_mac: eth_mac@34 {
reg = <0x34 0x10>;
};
bid: bid@46 {
reg = <0x46 0x30>;
};
};
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10
(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
};
xtal: xtal-clk {
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "xtal";
#clock-cells = <0>;
};
soc {
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
ranges;
usb0_phy: phy@c0000000 {
compatible = "amlogic,meson-gxbb-usb2-phy";
#phy-cells = <0>;
@ -170,462 +92,23 @@ usb1_phy: phy@c0000020 {
status = "disabled";
};
cbus: cbus@c1100000 {
compatible = "simple-bus";
reg = <0x0 0xc1100000 0x0 0x100000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
sram: sram@c8000000 {
compatible = "amlogic,meson-gxbb-sram", "mmio-sram";
reg = <0x0 0xc8000000 0x0 0x14000>;
reset: reset-controller@4404 {
compatible = "amlogic,meson-gxbb-reset";
reg = <0x0 0x04404 0x0 0x20>;
#reset-cells = <1>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x0 0xc8000000 0x14000>;
cpu_scp_lpri: scp-shmem@0 {
compatible = "amlogic,meson-gxbb-scp-shmem";
reg = <0x13000 0x400>;
};
uart_A: serial@84c0 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x84c0 0x0 0x14>;
interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
cpu_scp_hpri: scp-shmem@200 {
compatible = "amlogic,meson-gxbb-scp-shmem";
reg = <0x13400 0x400>;
};
uart_B: serial@84dc {
compatible = "amlogic,meson-uart";
reg = <0x0 0x84dc 0x0 0x14>;
interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
pwm_ab: pwm@8550 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x08550 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
pwm_cd: pwm@8650 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x08650 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
pwm_ef: pwm@86c0 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x086c0 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
uart_C: serial@8700 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x8700 0x0 0x14>;
interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
watchdog@98d0 {
compatible = "amlogic,meson-gxbb-wdt";
reg = <0x0 0x098d0 0x0 0x10>;
clocks = <&xtal>;
};
spifc: spi@8c80 {
compatible = "amlogic,meson-gxbb-spifc";
reg = <0x0 0x08c80 0x0 0x80>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&clkc CLKID_SPI>;
status = "disabled";
};
i2c_A: i2c@8500 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x08500 0x0 0x20>;
interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c_B: i2c@87c0 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087c0 0x0 0x20>;
interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c_C: i2c@87e0 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087e0 0x0 0x20>;
interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gic: interrupt-controller@c4301000 {
compatible = "arm,gic-400";
reg = <0x0 0xc4301000 0 0x1000>,
<0x0 0xc4302000 0 0x2000>,
<0x0 0xc4304000 0 0x2000>,
<0x0 0xc4306000 0 0x2000>;
interrupt-controller;
interrupts = <GIC_PPI 9
(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
#interrupt-cells = <3>;
#address-cells = <0>;
};
aobus: aobus@c8100000 {
compatible = "simple-bus";
reg = <0x0 0xc8100000 0x0 0x100000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
pinctrl_aobus: pinctrl@14 {
compatible = "amlogic,meson-gxbb-aobus-pinctrl";
#address-cells = <2>;
#size-cells = <2>;
ranges;
gpio_ao: bank@14 {
reg = <0x0 0x00014 0x0 0x8>,
<0x0 0x0002c 0x0 0x4>,
<0x0 0x00024 0x0 0x8>;
reg-names = "mux", "pull", "gpio";
gpio-controller;
#gpio-cells = <2>;
};
uart_ao_a_pins: uart_ao_a {
mux {
groups = "uart_tx_ao_a", "uart_rx_ao_a";
function = "uart_ao";
};
};
remote_input_ao_pins: remote_input_ao {
mux {
groups = "remote_input_ao";
function = "remote_input_ao";
};
};
i2c_ao_pins: i2c_ao {
mux {
groups = "i2c_sck_ao",
"i2c_sda_ao";
function = "i2c_ao";
};
};
pwm_ao_a_3_pins: pwm_ao_a_3 {
mux {
groups = "pwm_ao_a_3";
function = "pwm_ao_a_3";
};
};
pwm_ao_a_6_pins: pwm_ao_a_6 {
mux {
groups = "pwm_ao_a_6";
function = "pwm_ao_a_6";
};
};
pwm_ao_a_12_pins: pwm_ao_a_12 {
mux {
groups = "pwm_ao_a_12";
function = "pwm_ao_a_12";
};
};
pwm_ao_b_pins: pwm_ao_b {
mux {
groups = "pwm_ao_b";
function = "pwm_ao_b";
};
};
};
clkc_AO: clock-controller@040 {
compatible = "amlogic,gxbb-aoclkc";
reg = <0x0 0x00040 0x0 0x4>;
#clock-cells = <1>;
#reset-cells = <1>;
};
uart_AO: serial@4c0 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x004c0 0x0 0x14>;
interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
ir: ir@580 {
compatible = "amlogic,meson-gxbb-ir";
reg = <0x0 0x00580 0x0 0x40>;
interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
pwm_ab_AO: pwm@550 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x0550 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
i2c_AO: i2c@500 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x500 0x0 0x20>;
interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_AO_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
periphs: periphs@c8834000 {
compatible = "simple-bus";
reg = <0x0 0xc8834000 0x0 0x2000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
rng {
compatible = "amlogic,meson-rng";
reg = <0x0 0x0 0x0 0x4>;
};
pinctrl_periphs: pinctrl@4b0 {
compatible = "amlogic,meson-gxbb-periphs-pinctrl";
#address-cells = <2>;
#size-cells = <2>;
ranges;
gpio: bank@4b0 {
reg = <0x0 0x004b0 0x0 0x28>,
<0x0 0x004e8 0x0 0x14>,
<0x0 0x00120 0x0 0x14>,
<0x0 0x00430 0x0 0x40>;
reg-names = "mux", "pull", "pull-enable", "gpio";
gpio-controller;
#gpio-cells = <2>;
};
emmc_pins: emmc {
mux {
groups = "emmc_nand_d07",
"emmc_cmd",
"emmc_clk";
function = "emmc";
};
};
nor_pins: nor {
mux {
groups = "nor_d",
"nor_q",
"nor_c",
"nor_cs";
function = "nor";
};
};
sdcard_pins: sdcard {
mux {
groups = "sdcard_d0",
"sdcard_d1",
"sdcard_d2",
"sdcard_d3",
"sdcard_cmd",
"sdcard_clk";
function = "sdcard";
};
};
sdio_pins: sdio {
mux {
groups = "sdio_d0",
"sdio_d1",
"sdio_d2",
"sdio_d3",
"sdio_cmd",
"sdio_clk";
function = "sdio";
};
};
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
function = "sdio";
};
};
uart_a_pins: uart_a {
mux {
groups = "uart_tx_a",
"uart_rx_a";
function = "uart_a";
};
};
uart_b_pins: uart_b {
mux {
groups = "uart_tx_b",
"uart_rx_b";
function = "uart_b";
};
};
uart_c_pins: uart_c {
mux {
groups = "uart_tx_c",
"uart_rx_c";
function = "uart_c";
};
};
i2c_a_pins: i2c_a {
mux {
groups = "i2c_sck_a",
"i2c_sda_a";
function = "i2c_a";
};
};
i2c_b_pins: i2c_b {
mux {
groups = "i2c_sck_b",
"i2c_sda_b";
function = "i2c_b";
};
};
i2c_c_pins: i2c_c {
mux {
groups = "i2c_sck_c",
"i2c_sda_c";
function = "i2c_c";
};
};
eth_pins: eth_c {
mux {
groups = "eth_mdio",
"eth_mdc",
"eth_clk_rx_clk",
"eth_rx_dv",
"eth_rxd0",
"eth_rxd1",
"eth_rxd2",
"eth_rxd3",
"eth_rgmii_tx_clk",
"eth_tx_en",
"eth_txd0",
"eth_txd1",
"eth_txd2",
"eth_txd3";
function = "eth";
};
};
pwm_a_x_pins: pwm_a_x {
mux {
groups = "pwm_a_x";
function = "pwm_a_x";
};
};
pwm_a_y_pins: pwm_a_y {
mux {
groups = "pwm_a_y";
function = "pwm_a_y";
};
};
pwm_b_pins: pwm_b {
mux {
groups = "pwm_b";
function = "pwm_b";
};
};
pwm_d_pins: pwm_d {
mux {
groups = "pwm_d";
function = "pwm_d";
};
};
pwm_e_pins: pwm_e {
mux {
groups = "pwm_e";
function = "pwm_e";
};
};
pwm_f_x_pins: pwm_f_x {
mux {
groups = "pwm_f_x";
function = "pwm_f_x";
};
};
pwm_f_y_pins: pwm_f_y {
mux {
groups = "pwm_f_y";
function = "pwm_f_y";
};
};
};
};
hiubus: hiubus@c883c000 {
compatible = "simple-bus";
reg = <0x0 0xc883c000 0x0 0x2000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
clkc: clock-controller@0 {
compatible = "amlogic,gxbb-clkc";
#clock-cells = <1>;
reg = <0x0 0x0 0x0 0x3db>;
};
mailbox: mailbox@404 {
compatible = "amlogic,meson-gxbb-mhu";
reg = <0 0x404 0 0x4c>;
interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
<0 209 IRQ_TYPE_EDGE_RISING>,
<0 210 IRQ_TYPE_EDGE_RISING>;
#mbox-cells = <1>;
};
};
apb: apb@d0000000 {
compatible = "simple-bus";
reg = <0x0 0xd0000000 0x0 0x200000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
};
usb0: usb@c9000000 {
@ -651,19 +134,374 @@ usb1: usb@c9100000 {
dr_mode = "host";
status = "disabled";
};
};
};
ethmac: ethernet@c9410000 {
compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
reg = <0x0 0xc9410000 0x0 0x10000
0x0 0xc8834540 0x0 0x4>;
interrupts = <0 8 1>;
interrupt-names = "macirq";
clocks = <&clkc CLKID_ETH>,
<&clkc CLKID_FCLK_DIV2>,
<&clkc CLKID_MPLL2>;
clock-names = "stmmaceth", "clkin0", "clkin1";
phy-mode = "rgmii";
status = "disabled";
&cpu0 {
clocks = <&scpi_dvfs 0>;
};
&cpu1 {
clocks = <&scpi_dvfs 0>;
};
&cpu2 {
clocks = <&scpi_dvfs 0>;
};
&cpu3 {
clocks = <&scpi_dvfs 0>;
};
&cbus {
spifc: spi@8c80 {
compatible = "amlogic,meson-gxbb-spifc";
reg = <0x0 0x08c80 0x0 0x80>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&clkc CLKID_SPI>;
status = "disabled";
};
};
&ethmac {
clocks = <&clkc CLKID_ETH>,
<&clkc CLKID_FCLK_DIV2>,
<&clkc CLKID_MPLL2>;
clock-names = "stmmaceth", "clkin0", "clkin1";
};
&aobus {
pinctrl_aobus: pinctrl@14 {
compatible = "amlogic,meson-gxbb-aobus-pinctrl";
#address-cells = <2>;
#size-cells = <2>;
ranges;
gpio_ao: bank@14 {
reg = <0x0 0x00014 0x0 0x8>,
<0x0 0x0002c 0x0 0x4>,
<0x0 0x00024 0x0 0x8>;
reg-names = "mux", "pull", "gpio";
gpio-controller;
#gpio-cells = <2>;
};
uart_ao_a_pins: uart_ao_a {
mux {
groups = "uart_tx_ao_a", "uart_rx_ao_a";
function = "uart_ao";
};
};
remote_input_ao_pins: remote_input_ao {
mux {
groups = "remote_input_ao";
function = "remote_input_ao";
};
};
i2c_ao_pins: i2c_ao {
mux {
groups = "i2c_sck_ao",
"i2c_sda_ao";
function = "i2c_ao";
};
};
pwm_ao_a_3_pins: pwm_ao_a_3 {
mux {
groups = "pwm_ao_a_3";
function = "pwm_ao_a_3";
};
};
pwm_ao_a_6_pins: pwm_ao_a_6 {
mux {
groups = "pwm_ao_a_6";
function = "pwm_ao_a_6";
};
};
pwm_ao_a_12_pins: pwm_ao_a_12 {
mux {
groups = "pwm_ao_a_12";
function = "pwm_ao_a_12";
};
};
pwm_ao_b_pins: pwm_ao_b {
mux {
groups = "pwm_ao_b";
function = "pwm_ao_b";
};
};
};
clkc_AO: clock-controller@040 {
compatible = "amlogic,gxbb-aoclkc";
reg = <0x0 0x00040 0x0 0x4>;
#clock-cells = <1>;
#reset-cells = <1>;
};
pwm_ab_AO: pwm@550 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x0550 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
i2c_AO: i2c@500 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x500 0x0 0x20>;
interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_AO_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
&periphs {
pinctrl_periphs: pinctrl@4b0 {
compatible = "amlogic,meson-gxbb-periphs-pinctrl";
#address-cells = <2>;
#size-cells = <2>;
ranges;
gpio: bank@4b0 {
reg = <0x0 0x004b0 0x0 0x28>,
<0x0 0x004e8 0x0 0x14>,
<0x0 0x00120 0x0 0x14>,
<0x0 0x00430 0x0 0x40>;
reg-names = "mux", "pull", "pull-enable", "gpio";
gpio-controller;
#gpio-cells = <2>;
};
emmc_pins: emmc {
mux {
groups = "emmc_nand_d07",
"emmc_cmd",
"emmc_clk",
"emmc_ds";
function = "emmc";
};
};
nor_pins: nor {
mux {
groups = "nor_d",
"nor_q",
"nor_c",
"nor_cs";
function = "nor";
};
};
sdcard_pins: sdcard {
mux {
groups = "sdcard_d0",
"sdcard_d1",
"sdcard_d2",
"sdcard_d3",
"sdcard_cmd",
"sdcard_clk";
function = "sdcard";
};
};
sdio_pins: sdio {
mux {
groups = "sdio_d0",
"sdio_d1",
"sdio_d2",
"sdio_d3",
"sdio_cmd",
"sdio_clk";
function = "sdio";
};
};
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
function = "sdio";
};
};
uart_a_pins: uart_a {
mux {
groups = "uart_tx_a",
"uart_rx_a";
function = "uart_a";
};
};
uart_b_pins: uart_b {
mux {
groups = "uart_tx_b",
"uart_rx_b";
function = "uart_b";
};
};
uart_c_pins: uart_c {
mux {
groups = "uart_tx_c",
"uart_rx_c";
function = "uart_c";
};
};
i2c_a_pins: i2c_a {
mux {
groups = "i2c_sck_a",
"i2c_sda_a";
function = "i2c_a";
};
};
i2c_b_pins: i2c_b {
mux {
groups = "i2c_sck_b",
"i2c_sda_b";
function = "i2c_b";
};
};
i2c_c_pins: i2c_c {
mux {
groups = "i2c_sck_c",
"i2c_sda_c";
function = "i2c_c";
};
};
eth_rgmii_pins: eth-rgmii {
mux {
groups = "eth_mdio",
"eth_mdc",
"eth_clk_rx_clk",
"eth_rx_dv",
"eth_rxd0",
"eth_rxd1",
"eth_rxd2",
"eth_rxd3",
"eth_rgmii_tx_clk",
"eth_tx_en",
"eth_txd0",
"eth_txd1",
"eth_txd2",
"eth_txd3";
function = "eth";
};
};
eth_rmii_pins: eth-rmii {
mux {
groups = "eth_mdio",
"eth_mdc",
"eth_clk_rx_clk",
"eth_rx_dv",
"eth_rxd0",
"eth_rxd1",
"eth_tx_en",
"eth_txd0",
"eth_txd1";
function = "eth";
};
};
pwm_a_x_pins: pwm_a_x {
mux {
groups = "pwm_a_x";
function = "pwm_a_x";
};
};
pwm_a_y_pins: pwm_a_y {
mux {
groups = "pwm_a_y";
function = "pwm_a_y";
};
};
pwm_b_pins: pwm_b {
mux {
groups = "pwm_b";
function = "pwm_b";
};
};
pwm_d_pins: pwm_d {
mux {
groups = "pwm_d";
function = "pwm_d";
};
};
pwm_e_pins: pwm_e {
mux {
groups = "pwm_e";
function = "pwm_e";
};
};
pwm_f_x_pins: pwm_f_x {
mux {
groups = "pwm_f_x";
function = "pwm_f_x";
};
};
pwm_f_y_pins: pwm_f_y {
mux {
groups = "pwm_f_y";
function = "pwm_f_y";
};
};
};
};
&hiubus {
clkc: clock-controller@0 {
compatible = "amlogic,gxbb-clkc";
#clock-cells = <1>;
reg = <0x0 0x0 0x0 0x3db>;
};
};
&i2c_A {
clocks = <&clkc CLKID_I2C>;
};
&i2c_B {
clocks = <&clkc CLKID_I2C>;
};
&i2c_C {
clocks = <&clkc CLKID_I2C>;
};
&sd_emmc_a {
clocks = <&clkc CLKID_SD_EMMC_A>,
<&xtal>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_b {
clocks = <&clkc CLKID_SD_EMMC_B>,
<&xtal>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_c {
clocks = <&clkc CLKID_SD_EMMC_C>,
<&xtal>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};

76
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts Normal file
View file

@ -0,0 +1,76 @@
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "meson-gxl-s905d-p23x.dtsi"
/ {
compatible = "amlogic,p230", "amlogic,s905d", "amlogic,meson-gxl";
model = "Amlogic Meson GXL (S905D) P230 Development Board";
};
/* P230 has exclusive choice between internal or external PHY */
&ethmac {
pinctrl-0 = <&eth_pins>;
pinctrl-names = "default";
/* Select external PHY by default */
phy-handle = <&external_phy>;
/* External PHY reset is shared with internal PHY Led signals */
snps,reset-gpio = <&gpio GPIOZ_14 0>;
snps,reset-delays-us = <0 10000 1000000>;
snps,reset-active-low;
/* External PHY is in RGMII */
phy-mode = "rgmii";
};
&external_mdio {
external_phy: ethernet-phy@0 {
compatible = "ethernet-phy-id001c.c916", "ethernet-phy-ieee802.3-c22";
reg = <0>;
max-speed = <1000>;
};
};

57
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p231.dts Normal file
View file

@ -0,0 +1,57 @@
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "meson-gxl-s905d-p23x.dtsi"
/ {
compatible = "amlogic,p231", "amlogic,s905d", "amlogic,meson-gxl";
model = "Amlogic Meson GXL (S905D) P231 Development Board";
};
/* P231 has only internal PHY port */
&ethmac {
phy-mode = "rmii";
phy-handle = <&internal_phy>;
};

188
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi Normal file
View file

@ -0,0 +1,188 @@
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "meson-gxl-s905d.dtsi"
/ {
aliases {
serial0 = &uart_AO;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
};
/* This UART is brought out to the DB9 connector */
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
/* Wireless SDIO Module */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
non-removable;
disable-wp;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
brcmf: bcrmf@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-names = "default";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
cd-inverted;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
pinctrl-names = "default";
bus-width = <8>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vddio_boot>;
};
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
&ethmac {
status = "okay";
};

48
arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi Normal file
View file

@ -0,0 +1,48 @@
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "meson-gxl.dtsi"
/ {
compatible = "amlogic,s905d", "amlogic,meson-gxl";
};

69
arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts Normal file
View file

@ -0,0 +1,69 @@
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "meson-gxl-s905x.dtsi"
/ {
compatible = "amlogic,p212", "amlogic,s905x", "amlogic,meson-gxl";
model = "Amlogic Meson GXL (S905X) P212 Development Board";
aliases {
serial0 = &uart_AO;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
};
/* This UART is brought out to the DB9 connector */
&uart_AO {
status = "okay";
};

54
arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi Normal file
View file

@ -0,0 +1,54 @@
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "meson-gxl.dtsi"
/ {
compatible = "amlogic,s905x", "amlogic,meson-gxl";
};
/* S905X Only has access to its internal PHY */
&ethmac {
phy-mode = "rmii";
phy-handle = <&internal_phy>;
};

301
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi Normal file
View file

@ -0,0 +1,301 @@
/*
* Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "meson-gx.dtsi"
#include <dt-bindings/clock/gxbb-clkc.h>
#include <dt-bindings/gpio/meson-gxbb-gpio.h>
/ {
compatible = "amlogic,meson-gxl";
};
&ethmac {
reg = <0x0 0xc9410000 0x0 0x10000
0x0 0xc8834540 0x0 0x4>;
clocks = <&clkc CLKID_ETH>,
<&clkc CLKID_FCLK_DIV2>,
<&clkc CLKID_MPLL2>;
clock-names = "stmmaceth", "clkin0", "clkin1";
mdio0: mdio {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
};
};
&aobus {
pinctrl_aobus: pinctrl@14 {
compatible = "amlogic,meson-gxl-aobus-pinctrl";
#address-cells = <2>;
#size-cells = <2>;
ranges;
gpio_ao: bank@14 {
reg = <0x0 0x00014 0x0 0x8>,
<0x0 0x0002c 0x0 0x4>,
<0x0 0x00024 0x0 0x8>;
reg-names = "mux", "pull", "gpio";
gpio-controller;
#gpio-cells = <2>;
};
uart_ao_a_pins: uart_ao_a {
mux {
groups = "uart_tx_ao_a", "uart_rx_ao_a";
function = "uart_ao";
};
};
remote_input_ao_pins: remote_input_ao {
mux {
groups = "remote_input_ao";
function = "remote_input_ao";
};
};
};
};
&periphs {
pinctrl_periphs: pinctrl@4b0 {
compatible = "amlogic,meson-gxl-periphs-pinctrl";
#address-cells = <2>;
#size-cells = <2>;
ranges;
gpio: bank@4b0 {
reg = <0x0 0x004b0 0x0 0x28>,
<0x0 0x004e8 0x0 0x14>,
<0x0 0x00120 0x0 0x14>,
<0x0 0x00430 0x0 0x40>;
reg-names = "mux", "pull", "pull-enable", "gpio";
gpio-controller;
#gpio-cells = <2>;
};
emmc_pins: emmc {
mux {
groups = "emmc_nand_d07",
"emmc_cmd",
"emmc_clk",
"emmc_ds";
function = "emmc";
};
};
sdcard_pins: sdcard {
mux {
groups = "sdcard_d0",
"sdcard_d1",
"sdcard_d2",
"sdcard_d3",
"sdcard_cmd",
"sdcard_clk";
function = "sdcard";
};
};
sdio_pins: sdio {
mux {
groups = "sdio_d0",
"sdio_d1",
"sdio_d2",
"sdio_d3",
"sdio_cmd",
"sdio_clk";
function = "sdio";
};
};
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
function = "sdio";
};
};
uart_a_pins: uart_a {
mux {
groups = "uart_tx_a",
"uart_rx_a";
function = "uart_a";
};
};
uart_b_pins: uart_b {
mux {
groups = "uart_tx_b",
"uart_rx_b";
function = "uart_b";
};
};
uart_c_pins: uart_c {
mux {
groups = "uart_tx_c",
"uart_rx_c";
function = "uart_c";
};
};
i2c_a_pins: i2c_a {
mux {
groups = "i2c_sck_a",
"i2c_sda_a";
function = "i2c_a";
};
};
i2c_b_pins: i2c_b {
mux {
groups = "i2c_sck_b",
"i2c_sda_b";
function = "i2c_b";
};
};
i2c_c_pins: i2c_c {
mux {
groups = "i2c_sck_c",
"i2c_sda_c";
function = "i2c_c";
};
};
eth_pins: eth_c {
mux {
groups = "eth_mdio",
"eth_mdc",
"eth_clk_rx_clk",
"eth_rx_dv",
"eth_rxd0",
"eth_rxd1",
"eth_rxd2",
"eth_rxd3",
"eth_rgmii_tx_clk",
"eth_tx_en",
"eth_txd0",
"eth_txd1",
"eth_txd2",
"eth_txd3";
function = "eth";
};
};
pwm_e_pins: pwm_e {
mux {
groups = "pwm_e";
function = "pwm_e";
};
};
};
eth-phy-mux {
compatible = "mdio-mux-mmioreg", "mdio-mux";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x0 0x55c 0x0 0x4>;
mux-mask = <0xffffffff>;
mdio-parent-bus = <&mdio0>;
internal_mdio: mdio@e40908ff {
reg = <0xe40908ff>;
#address-cells = <1>;
#size-cells = <0>;
internal_phy: ethernet-phy@8 {
compatible = "ethernet-phy-id0181.4400", "ethernet-phy-ieee802.3-c22";
reg = <8>;
max-speed = <100>;
};
};
external_mdio: mdio@2009087f {
reg = <0x2009087f>;
#address-cells = <1>;
#size-cells = <0>;
};
};
};
&hiubus {
clkc: clock-controller@0 {
compatible = "amlogic,gxl-clkc", "amlogic,gxbb-clkc";
#clock-cells = <1>;
reg = <0x0 0x0 0x0 0x3db>;
};
};
&i2c_A {
clocks = <&clkc CLKID_I2C>;
};
&i2c_B {
clocks = <&clkc CLKID_I2C>;
};
&i2c_C {
clocks = <&clkc CLKID_I2C>;
};
&sd_emmc_a {
clocks = <&clkc CLKID_SD_EMMC_A>,
<&xtal>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_b {
clocks = <&clkc CLKID_SD_EMMC_B>,
<&xtal>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_c {
clocks = <&clkc CLKID_SD_EMMC_C>,
<&xtal>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};