networking: e100.rst: Get rid of Sphinx warnings

Documentation/networking/e100.rst:57: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:68: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:75: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:84: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:93: WARNING: Inline emphasis start-string without end-string.

While here, fix some highlights.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit is contained in:
Mauro Carvalho Chehab 2018-06-26 06:49:09 -03:00 committed by Jeff Kirsher
parent c411104115
commit b203cc7a4f

View file

@ -47,41 +47,45 @@ Driver Configuration Parameters
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
Rx Descriptors:
Number of receive descriptors. A receive descriptor is a data
structure that describes a receive buffer and its attributes to the network
controller. The data in the descriptor is used by the controller to write
data from the controller to host memory. In the 3.x.x driver the valid range
for this parameter is 64-256. The default value is 256. This parameter can be
changed using the command::
ethtool -G eth? rx n
ethtool -G eth? rx n
Where n is the number of desired Rx descriptors.
Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
Tx Descriptors:
Number of transmit descriptors. A transmit descriptor is a data
structure that describes a transmit buffer and its attributes to the network
controller. The data in the descriptor is used by the controller to read
data from the host memory to the controller. In the 3.x.x driver the valid
range for this parameter is 64-256. The default value is 128. This parameter
can be changed using the command::
ethtool -G eth? tx n
ethtool -G eth? tx n
Where n is the number of desired Tx descriptors.
Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
Speed/Duplex:
The driver auto-negotiates the link speed and duplex settings by
default. The ethtool utility can be used as follows to force speed/duplex.::
ethtool -s eth? autoneg off speed {10|100} duplex {full|half}
ethtool -s eth? autoneg off speed {10|100} duplex {full|half}
NOTE: setting the speed/duplex to incorrect values will cause the link to
fail.
Event Log Message Level: The driver uses the message level flag to log events
Event Log Message Level:
The driver uses the message level flag to log events
to syslog. The message level can be set at driver load time. It can also be
set using the command::
ethtool -s eth? msglvl n
ethtool -s eth? msglvl n
Additional Configurations
@ -92,7 +96,7 @@ Configuring the Driver on Different Distributions
Configuring a network driver to load properly when the system is started
is distribution dependent. Typically, the configuration process involves
adding an alias line to /etc/modprobe.d/*.conf as well as editing other
adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other
system startup scripts and/or configuration files. Many popular Linux
distributions ship with tools to make these changes for you. To learn
the proper way to configure a network device for your system, refer to
@ -160,7 +164,10 @@ This results in unbalanced receive traffic.
If you have multiple interfaces in a server, either turn on ARP
filtering by
(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
(1) entering::
echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
(this only works if your kernel's version is higher than 2.4.5), or
(2) installing the interfaces in separate broadcast domains (either