diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index a29f8012fb08..a0cc0edafc78 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -305,6 +305,14 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(INTEL, 0x9c85), board_ahci }, /* Wildcat Point-LP RAID */ { PCI_VDEVICE(INTEL, 0x9c87), board_ahci }, /* Wildcat Point-LP RAID */ { PCI_VDEVICE(INTEL, 0x9c8f), board_ahci }, /* Wildcat Point-LP RAID */ + { PCI_VDEVICE(INTEL, 0x8c82), board_ahci }, /* 9 Series AHCI */ + { PCI_VDEVICE(INTEL, 0x8c83), board_ahci }, /* 9 Series AHCI */ + { PCI_VDEVICE(INTEL, 0x8c84), board_ahci }, /* 9 Series RAID */ + { PCI_VDEVICE(INTEL, 0x8c85), board_ahci }, /* 9 Series RAID */ + { PCI_VDEVICE(INTEL, 0x8c86), board_ahci }, /* 9 Series RAID */ + { PCI_VDEVICE(INTEL, 0x8c87), board_ahci }, /* 9 Series RAID */ + { PCI_VDEVICE(INTEL, 0x8c8e), board_ahci }, /* 9 Series RAID */ + { PCI_VDEVICE(INTEL, 0x8c8f), board_ahci }, /* 9 Series RAID */ /* JMicron 360/1/3/5/6, match class to avoid IDE function */ { PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, @@ -442,6 +450,8 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x917a), .driver_data = board_ahci_yes_fbs }, /* 88se9172 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9172), + .driver_data = board_ahci_yes_fbs }, /* 88se9182 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9182), .driver_data = board_ahci_yes_fbs }, /* 88se9172 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9192), .driver_data = board_ahci_yes_fbs }, /* 88se9172 on some Gigabyte */ @@ -1329,6 +1339,18 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) else if (pdev->vendor == 0x1c44 && pdev->device == 0x8000) ahci_pci_bar = AHCI_PCI_BAR_ENMOTUS; + /* + * The JMicron chip 361/363 contains one SATA controller and one + * PATA controller,for powering on these both controllers, we must + * follow the sequence one by one, otherwise one of them can not be + * powered on successfully, so here we disable the async suspend + * method for these chips. + */ + if (pdev->vendor == PCI_VENDOR_ID_JMICRON && + (pdev->device == PCI_DEVICE_ID_JMICRON_JMB363 || + pdev->device == PCI_DEVICE_ID_JMICRON_JMB361)) + device_disable_async_suspend(&pdev->dev); + /* acquire resources */ rc = pcim_enable_device(pdev); if (rc) diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c index f1fef74e503c..032904402c95 100644 --- a/drivers/ata/ahci_tegra.c +++ b/drivers/ata/ahci_tegra.c @@ -18,14 +18,17 @@ */ #include -#include #include #include #include #include #include #include +#include + +#include #include + #include "ahci.h" #define SATA_CONFIGURATION_0 0x180 @@ -180,9 +183,12 @@ static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv) /* Pad calibration */ - /* FIXME Always use calibration 0. Change this to read the calibration - * fuse once the fuse driver has landed. */ - val = 0; + ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); + if (ret) { + dev_err(&tegra->pdev->dev, + "failed to read calibration fuse: %d\n", ret); + return ret; + } calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; diff --git a/drivers/ata/ahci_xgene.c b/drivers/ata/ahci_xgene.c index c6962300b93c..f03aab187f4d 100644 --- a/drivers/ata/ahci_xgene.c +++ b/drivers/ata/ahci_xgene.c @@ -78,6 +78,9 @@ #define CFG_MEM_RAM_SHUTDOWN 0x00000070 #define BLOCK_MEM_RDY 0x00000074 +/* Max retry for link down */ +#define MAX_LINK_DOWN_RETRY 3 + struct xgene_ahci_context { struct ahci_host_priv *hpriv; struct device *dev; @@ -145,6 +148,14 @@ static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc) return rc; } +static bool xgene_ahci_is_memram_inited(struct xgene_ahci_context *ctx) +{ + void __iomem *diagcsr = ctx->csr_diag; + + return (readl(diagcsr + CFG_MEM_RAM_SHUTDOWN) == 0 && + readl(diagcsr + BLOCK_MEM_RDY) == 0xFFFFFFFF); +} + /** * xgene_ahci_read_id - Read ID data from the specified device * @dev: device @@ -229,8 +240,11 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel) * and Gen1 (1.5Gbps). Otherwise during long IO stress test, the PHY will * report disparity error and etc. In addition, during COMRESET, there can * be error reported in the register PORT_SCR_ERR. For SERR_DISPARITY and - * SERR_10B_8B_ERR, the PHY receiver line must be reseted. The following - * algorithm is followed to proper configure the hardware PHY during COMRESET: + * SERR_10B_8B_ERR, the PHY receiver line must be reseted. Also during long + * reboot cycle regression, sometimes the PHY reports link down even if the + * device is present because of speed negotiation failure. so need to retry + * the COMRESET to get the link up. The following algorithm is followed to + * proper configure the hardware PHY during COMRESET: * * Alg Part 1: * 1. Start the PHY at Gen3 speed (default setting) @@ -246,9 +260,15 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel) * Alg Part 2: * 1. On link up, if there are any SERR_DISPARITY and SERR_10B_8B_ERR error * reported in the register PORT_SCR_ERR, then reset the PHY receiver line - * 2. Go to Alg Part 3 + * 2. Go to Alg Part 4 * * Alg Part 3: + * 1. Check the PORT_SCR_STAT to see whether device presence detected but PHY + * communication establishment failed and maximum link down attempts are + * less than Max attempts 3 then goto Alg Part 1. + * 2. Go to Alg Part 4. + * + * Alg Part 4: * 1. Clear any pending from register PORT_SCR_ERR. * * NOTE: For the initial version, we will NOT support Gen1/Gen2. In addition @@ -267,19 +287,27 @@ static int xgene_ahci_do_hardreset(struct ata_link *link, u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG; void __iomem *port_mmio = ahci_port_base(ap); struct ata_taskfile tf; + int link_down_retry = 0; int rc; - u32 val; + u32 val, sstatus; - /* clear D2H reception area to properly wait for D2H FIS */ - ata_tf_init(link->device, &tf); - tf.command = ATA_BUSY; - ata_tf_to_fis(&tf, 0, 0, d2h_fis); - rc = sata_link_hardreset(link, timing, deadline, online, + do { + /* clear D2H reception area to properly wait for D2H FIS */ + ata_tf_init(link->device, &tf); + tf.command = ATA_BUSY; + ata_tf_to_fis(&tf, 0, 0, d2h_fis); + rc = sata_link_hardreset(link, timing, deadline, online, ahci_check_ready); + if (*online) { + val = readl(port_mmio + PORT_SCR_ERR); + if (val & (SERR_DISPARITY | SERR_10B_8B_ERR)) + dev_warn(ctx->dev, "link has error\n"); + break; + } - val = readl(port_mmio + PORT_SCR_ERR); - if (val & (SERR_DISPARITY | SERR_10B_8B_ERR)) - dev_warn(ctx->dev, "link has error\n"); + sata_scr_read(link, SCR_STATUS, &sstatus); + } while (link_down_retry++ < MAX_LINK_DOWN_RETRY && + (sstatus & 0xff) == 0x1); /* clear all errors if any pending */ val = readl(port_mmio + PORT_SCR_ERR); @@ -467,6 +495,11 @@ static int xgene_ahci_probe(struct platform_device *pdev) return -ENODEV; } + if (xgene_ahci_is_memram_inited(ctx)) { + dev_info(dev, "skip clock and PHY initialization\n"); + goto skip_clk_phy; + } + /* Due to errata, HW requires full toggle transition */ rc = ahci_platform_enable_clks(hpriv); if (rc) @@ -479,7 +512,7 @@ static int xgene_ahci_probe(struct platform_device *pdev) /* Configure the host controller */ xgene_ahci_hw_init(hpriv); - +skip_clk_phy: hpriv->flags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_NO_NCQ; rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info); diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index 893e30e9a9ef..ffbe625e6fd2 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -340,6 +340,14 @@ static const struct pci_device_id piix_pci_tbl[] = { { 0x8086, 0x0F21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_byt }, /* SATA Controller IDE (Coleto Creek) */ { 0x8086, 0x23a6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata }, + /* SATA Controller IDE (9 Series) */ + { 0x8086, 0x8c88, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_snb }, + /* SATA Controller IDE (9 Series) */ + { 0x8086, 0x8c89, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_snb }, + /* SATA Controller IDE (9 Series) */ + { 0x8086, 0x8c80, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, + /* SATA Controller IDE (9 Series) */ + { 0x8086, 0x8c81, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb }, { } /* terminate list */ }; diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c index 4d1a5d2c4287..47e418b8c8ba 100644 --- a/drivers/ata/pata_jmicron.c +++ b/drivers/ata/pata_jmicron.c @@ -143,6 +143,18 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i }; const struct ata_port_info *ppi[] = { &info, NULL }; + /* + * The JMicron chip 361/363 contains one SATA controller and one + * PATA controller,for powering on these both controllers, we must + * follow the sequence one by one, otherwise one of them can not be + * powered on successfully, so here we disable the async suspend + * method for these chips. + */ + if (pdev->vendor == PCI_VENDOR_ID_JMICRON && + (pdev->device == PCI_DEVICE_ID_JMICRON_JMB363 || + pdev->device == PCI_DEVICE_ID_JMICRON_JMB361)) + device_disable_async_suspend(&pdev->dev); + return ata_pci_bmdma_init_one(pdev, ppi, &jmicron_sht, NULL, 0); }