ARM: dts: add support for Laird WB50N cpu module and DVK
This adds support for Lairds CPU module, featuring Atheros wifi, CSR Bluetooth and, Atmel SAMA5D3 CPU. https://www.lairdtech.com/products/wb50nbt-wi-fi-bluetooth-module Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This commit is contained in:
Ben Whitten
Alexandre Belloni
parent
0445655586
commit
e8274426b4
|
|
@ -52,6 +52,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
|
|||
at91-sama5d2_xplained.dtb \
|
||||
at91-sama5d3_xplained.dtb \
|
||||
at91-tse850-3.dtb \
|
||||
at91-wb50n.dtb \
|
||||
sama5d31ek.dtb \
|
||||
sama5d33ek.dtb \
|
||||
sama5d34ek.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,112 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* at91-wb50n.dts - Device Tree file for wb50n evaluation board
|
||||
*
|
||||
* Copyright (C) 2018 Laird
|
||||
*
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include "at91-wb50n.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
|
||||
compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
|
||||
|
||||
gpio_keys {
|
||||
compatible = "gpio-keys";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
btn0@10 {
|
||||
reg = <10>;
|
||||
label = "BTNESC";
|
||||
linux,code = <1>; /* ESC button */
|
||||
gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
|
||||
gpio-key,wakeup = <1>;
|
||||
};
|
||||
|
||||
irqbtn@31 {
|
||||
reg = <31>;
|
||||
label = "IRQBTN";
|
||||
linux,code = <99>; /* SysReq button */
|
||||
gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
|
||||
gpio-key,wakeup = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led0 {
|
||||
label = "wb50n:blue:led0";
|
||||
gpios = <&pioA 12 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led1 {
|
||||
label = "wb50n:green:led1";
|
||||
gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led2 {
|
||||
label = "wb50n:red:led2";
|
||||
gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mmc0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&macb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dbgu {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* On BB40 this port is labeled UART1 */
|
||||
&usart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* On BB40 this port is labeled UART0 */
|
||||
&usart1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi1 {
|
||||
status = "okay";
|
||||
|
||||
spidev@0 {
|
||||
compatible = "spidev";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <8000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
|
|
@ -0,0 +1,198 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* at91-wb50n.dtsi - Device Tree include file for wb50n cpu module
|
||||
*
|
||||
* Copyright (C) 2018 Laird
|
||||
*
|
||||
*/
|
||||
|
||||
#include "sama5d31.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
|
||||
compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
|
||||
|
||||
chosen {
|
||||
bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rw";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0x20000000 0x4000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
board {
|
||||
pinctrl_mmc0_cd: mmc0_cd {
|
||||
atmel,pins = <AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */
|
||||
};
|
||||
|
||||
pinctrl_usba_vbus: usba_vbus {
|
||||
atmel,pins = <AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&slow_xtal {
|
||||
clock-frequency = <32768>;
|
||||
};
|
||||
|
||||
&main_xtal {
|
||||
clock-frequency = <12000000>;
|
||||
};
|
||||
|
||||
&slow_osc {
|
||||
atmel,osc-bypass;
|
||||
};
|
||||
|
||||
&usart1_clk {
|
||||
atmel,clk-output-range = <0 132000000>;
|
||||
};
|
||||
|
||||
&mmc0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
|
||||
cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>;
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
bus-width = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
|
||||
status = "okay";
|
||||
atheros@0 {
|
||||
compatible = "atheros,ath6kl";
|
||||
atheros,board-id = "SD32";
|
||||
reg = <0>;
|
||||
bus-width = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
&macb1 {
|
||||
phy-mode = "rmii";
|
||||
};
|
||||
|
||||
&dbgu {
|
||||
dmas = <0>, <0>; /* Do not use DMA for dbgu */
|
||||
};
|
||||
|
||||
/* On BB40 this port is labeled UART1 */
|
||||
&usart0 {
|
||||
atmel,use-dma-rx;
|
||||
atmel,use-dma-tx;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>;
|
||||
};
|
||||
|
||||
/* On BB40 this port is labeled UART0 */
|
||||
&usart1 {
|
||||
atmel,use-dma-rx;
|
||||
atmel,use-dma-tx;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
|
||||
dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>;
|
||||
dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>;
|
||||
dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>;
|
||||
rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
/* USART3 is direct-connect to the Bluetooth UART on the radio SIP */
|
||||
&usart3 {
|
||||
atmel,use-dma-rx;
|
||||
atmel,use-dma-tx;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi1 {
|
||||
cs-gpios = <&pioC 25 0>, <0>, <0>, <0>;
|
||||
};
|
||||
|
||||
&ebi {
|
||||
pinctrl-0 = <&pinctrl_ebi_nand_addr>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&nand_controller {
|
||||
status = "okay";
|
||||
|
||||
nand: nand@3 {
|
||||
reg = <0x3 0x0 0x2>;
|
||||
atmel,rb = <0>;
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-mode = "hw";
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-on-flash-bbt;
|
||||
label = "atmel_nand";
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
at91bootstrap@0 {
|
||||
label = "at91bs";
|
||||
reg = <0x0 0x20000>;
|
||||
};
|
||||
|
||||
uboot@20000 {
|
||||
label = "u-boot";
|
||||
reg = <0x20000 0x80000>;
|
||||
};
|
||||
|
||||
ubootenv@a0000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0xa0000 0x20000>;
|
||||
};
|
||||
|
||||
ubootenv@c0000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0xc0000 0x20000>;
|
||||
};
|
||||
|
||||
kernel-a@e0000 {
|
||||
label = "kernel-a";
|
||||
reg = <0xe0000 0x500000>;
|
||||
};
|
||||
|
||||
kernel-b@5e0000 {
|
||||
label = "kernel-b";
|
||||
reg = <0x5e0000 0x500000>;
|
||||
};
|
||||
|
||||
rootfs-a@ae0000 {
|
||||
label = "rootfs-a";
|
||||
reg = <0xae0000 0x3000000>;
|
||||
};
|
||||
|
||||
rootfs-b@3ae0000 {
|
||||
label = "rootfs-b";
|
||||
reg = <0x3ae0000 0x3000000>;
|
||||
};
|
||||
|
||||
user@6ae0000 {
|
||||
label = "user";
|
||||
reg = <0x6ae0000 0x14e0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usba_vbus>;
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
num-ports = <3>;
|
||||
atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>;
|
||||
atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
Loading…
Reference in New Issue