mirrors/linux-stable
1
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git synced 2024-10-09 18:19:06 +00:00
Code Issues Releases Wiki Activity

Renesas ARM64 Based SoC DT Updates for v4.17

Browse source 
* R-Car Gen3 boards and SoCs
   - Make phy-mode of EtherAVB a board-specific property.
 
     The SoC DTs file now uses "rgmii" and boards override this with
     "rgmii-txid" as appropriate. Previously "rgmii-txid" was used
     in SoC DTs but this did not describe that more sophiticated
     functionality is a board rather than SoC property.
 
 * Condor board with R-Car V3H (r8a77980) SoC
   - Initial upstream support
 
 * Condor board with R-Car V3H (r8a77980) SoC
   - Initial upstream support
 
 * R-Car D3 (r8a77995)
   - Add I2C nodes and then describing the PCA9654 I/O expander connected to
     the I2C0 bus.
 
 * Eagle board with R-Car V3M (r8a77970) SoC
   - Enable PFC support for configuring SCIF0 pins
     This uses PFC support added to the V3M DT
 
   - Describe EtherAVB PHY IRQ
     This uses support for GPIO added to the V3M DT
 
   - Enable I2C0 support
 
     Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
     PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
     we're only describing the former chip now)."
 
 * R-Car V3M (r8a77970) SoCs
   - Add PFC support
   - Describe GPIO devices
   - Describe I2C devices
   - Srt subnodes of root node alphabetically to eas future maintence overhead
 
 * Draak board with R-Car D3 (r8a77995) SoC
   - Enable SDHI2
 
     Wolfram Sang says "The single SDHI controller is connected to eMMC."
 
   - Enable DU
 
     Kieran Bingham says "Enable the DU, providing only the VGA output for
     now."
 
 * R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
   - Move nodes which have no reg property out of bus
     By deffinition the bus only has hardware with an address on the bus
 
   - Remove non-existing STBE region from EtherAVB
     Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs
 
 * R-Car D3 (r8a77995) SoC
   - Add FCPV, VSP and DU support
 
     Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
     One VSPBS can be used as a dual-input image blender, while two VSPD
     instances can be utilised as part of a display (DU) pipeline.
 
     Add support for these, along with their required FCPV nodes."
 
 * Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
   - Add GPIO extender
     This is a basis for follow-up work to configure the GPIOs of the extender
 
 * Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
   - Initial upstream support
 
 * R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
   - Add OPPs table for cpu devices
     This, along with recently upstreamed Z and Z2 clock support allows
     use of CPUFreq with both A57 and A53 CPUs.
 
   - Add thermal cooling management
     Allows the use of CPUFreq as a cooling device on A57 CPUs
 
   - Correct register size of thermal node
 
     Niklas Söderlund says "To be able to read fused calibration values from
     hardware the size of the register resource of TSC1 needs to be
     incremented to cover one more register which holds the information if
     the calibration values have been fused or not.
 
     Instead of increasing TSC1 size to the value from the datasheet update
     all TSC's size to the smallest granularity of the address decoder
     circuitry"
 
   - Fix register mappings on VSPs
 
     Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
     register space is mapped correctly to support this."
 
 * R-Car H3 (r8a7795) SoC
   - Move SCIF node into alphabetical order to ease future maintenance overhead
 
   - Add IPMMU-PV1 device node
 
     This resolves an oversight when IPMMU nodes were added to the H3 DT.
     All IPMMU devices should now be described in DT.
 
   - Add missing SYS-DMAC2 dmas
 
     Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
     can make use of DMA are wired to either SYS-DMAC0 only, or to both
     SYS-DMAC1 and SYS-DMAC2.
 
     Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
     SCIF[0125], and I2C[0-2].  These were initially left out because early
     firmware versions prohibited using SYS-DMAC2.  This restriction has
     been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
     2016)."
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAlqrw1cACgkQ189kaWo3
 T75rUw/+LR1H1BeU8TpNeSsq6rb2jD4lJhGfj8UQP5mo2ycRzYfMiZSJgNqsiAd+
 C1XgKsEPRCCXhEt52H2cKUocYfGbYrDiUXmy3lHEPHwYENj2+QSjObkZvcLtH3rX
 6H6quvBMRbKigBKM2A+6CEG1z/zcGCA25KbLvEqJylADKugldkXn/ao/1yoSmbnX
 bqWDZmJ2tPfqFrmp8EVKfW75INLkJUTgzMWAdmUmABdWkLXWEBaGfCIcabwPxeNJ
 RJ9jG9P4CVuVhqR85Pii9XbInhYbbVmqkQRwP5jspSULBIxc1LKFLWJeWNfYjE2R
 9FkW2EHEKzwK24bg+/rCtjFoM/Uk7E9OwS75IGqQ+QXVTzLmjQAI5vEifVZyaBzU
 ei9eh52Q53yG4GEuknEtZe5chVUdoKGxU2KP5D5/OzCcXjrSymHT5eK+t2Anr/vn
 ATon2o9RXw9hzy9AeglYl1wA07Vh+VaeEUYp2klYIjm6gSB8e333YghgrI2KdTK3
 pTAgwmjDZRZzq4/mC7nr6LI6i0RS9Drf7uzSpYKGSKwnuTAgH3IdkYhRzRA+aY1u
 cRXTfWfMJvaE15C7JfhqbduC3DGBVfl5E8kgbPJK8d29DA6m5tB4L5zZ2J2N7q8X
 J3jKJSZUYZqDyGzTCd2pJfDzofcsrRyWTvDv1YfobQzeibRJqG8=
 =wu1f
 -----END PGP SIGNATURE-----

Merge tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM64 Based SoC DT Updates for v4.17" from Simon Horman:

* R-Car Gen3 boards and SoCs
  - Make phy-mode of EtherAVB a board-specific property.

    The SoC DTs file now uses "rgmii" and boards override this with
    "rgmii-txid" as appropriate. Previously "rgmii-txid" was used
    in SoC DTs but this did not describe that more sophiticated
    functionality is a board rather than SoC property.

* Condor board with R-Car V3H (r8a77980) SoC
  - Initial upstream support

* Condor board with R-Car V3H (r8a77980) SoC
  - Initial upstream support

* R-Car D3 (r8a77995)
  - Add I2C nodes and then describing the PCA9654 I/O expander connected to
    the I2C0 bus.

* Eagle board with R-Car V3M (r8a77970) SoC
  - Enable PFC support for configuring SCIF0 pins
    This uses PFC support added to the V3M DT

  - Describe EtherAVB PHY IRQ
    This uses support for GPIO added to the V3M DT

  - Enable I2C0 support

    Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
    PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
    we're only describing the former chip now)."

* R-Car V3M (r8a77970) SoCs
  - Add PFC support
  - Describe GPIO devices
  - Describe I2C devices
  - Srt subnodes of root node alphabetically to eas future maintence overhead

* Draak board with R-Car D3 (r8a77995) SoC
  - Enable SDHI2

    Wolfram Sang says "The single SDHI controller is connected to eMMC."

  - Enable DU

    Kieran Bingham says "Enable the DU, providing only the VGA output for
    now."

* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
  - Move nodes which have no reg property out of bus
    By deffinition the bus only has hardware with an address on the bus

  - Remove non-existing STBE region from EtherAVB
    Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs

* R-Car D3 (r8a77995) SoC
  - Add FCPV, VSP and DU support

    Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
    One VSPBS can be used as a dual-input image blender, while two VSPD
    instances can be utilised as part of a display (DU) pipeline.

    Add support for these, along with their required FCPV nodes."

* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
  - Add GPIO extender
    This is a basis for follow-up work to configure the GPIOs of the extender

* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
  - Initial upstream support

* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
  - Add OPPs table for cpu devices
    This, along with recently upstreamed Z and Z2 clock support allows
    use of CPUFreq with both A57 and A53 CPUs.

  - Add thermal cooling management
    Allows the use of CPUFreq as a cooling device on A57 CPUs

  - Correct register size of thermal node

    Niklas Söderlund says "To be able to read fused calibration values from
    hardware the size of the register resource of TSC1 needs to be
    incremented to cover one more register which holds the information if
    the calibration values have been fused or not.

    Instead of increasing TSC1 size to the value from the datasheet update
    all TSC's size to the smallest granularity of the address decoder
    circuitry"

  - Fix register mappings on VSPs

    Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
    register space is mapped correctly to support this."

* R-Car H3 (r8a7795) SoC
  - Move SCIF node into alphabetical order to ease future maintenance overhead

  - Add IPMMU-PV1 device node

    This resolves an oversight when IPMMU nodes were added to the H3 DT.
    All IPMMU devices should now be described in DT.

  - Add missing SYS-DMAC2 dmas

    Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
    can make use of DMA are wired to either SYS-DMAC0 only, or to both
    SYS-DMAC1 and SYS-DMAC2.

    Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
    SCIF[0125], and I2C[0-2].  These were initially left out because early
    firmware versions prohibited using SYS-DMAC2.  This restriction has
    been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
    2016)."

* tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
  arm64: dts: renesas: v3msk: add SCIF0 pins
  arm64: dts: renesas: r8a7795: Add missing SYS-DMAC2 dmas
  arm64: dts: renesas: r8a7795: Add IPMMU-PV1 device node
  arm64: dts: renesas: r8a77970: sort subnodes of root node alphabetically
  arm64: dts: renesas: eagle: add I2C0 support
  arm64: dts: renesas: r8a77970: add I2C support
  arm64: dts: renesas: r8a77965-salvator-xs: Add SoC name to file header
  arm64: dts: renesas: r8a77965: Add EtherAVB device node
  arm64: dts: renesas: r8a77970: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii"
  arm64: dts: renesas: v3msk: Override EtherAVB phy-mode
  arm64: dts: renesas: eagle: Override EtherAVB phy-mode
  arm64: dts: renesas: draak: Override EtherAVB phy-mode
  arm64: dts: renesas: ulcb: Override EtherAVB phy-mode
  arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode
  arm64: dts: renesas: r8a77965: Add INTC-EX device node
  arm64: dts: renesas: r8a77965: Add IIC-DVFS device node
  arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-N
  ...
This commit is contained in:
Arnd Bergmann 2018-03-27 13:28:10 +02:00
commit f02e0468c4
17 changed files with 2216 additions and 76 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

12
arch/arm64/Kconfig.platforms
View file

@ -190,12 +190,24 @@ config ARCH_R8A7796
help
This enables support for the Renesas R-Car M3-W SoC.
config ARCH_R8A77965
bool "Renesas R-Car M3-N SoC Platform"
depends on ARCH_RENESAS
help
This enables support for the Renesas R-Car M3-N SoC.
config ARCH_R8A77970
bool "Renesas R-Car V3M SoC Platform"
depends on ARCH_RENESAS
help
This enables support for the Renesas R-Car V3M SoC.
config ARCH_R8A77980
bool "Renesas R-Car V3H SoC Platform"
depends on ARCH_RENESAS
help
This enables support for the Renesas R-Car V3H SoC.
config ARCH_R8A77995
bool "Renesas R-Car D3 SoC Platform"
depends on ARCH_RENESAS

2
arch/arm64/boot/dts/renesas/Makefile
View file

@ -7,5 +7,7 @@ dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-h3ulcb-kf.dtb
dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-m3ulcb-kf.dtb
dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-xs.dtb
dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-salvator-x.dtb r8a77965-salvator-xs.dtb
dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle.dtb r8a77970-v3msk.dtb
dtb-$(CONFIG_ARCH_R8A77980) += r8a77980-condor.dtb
dtb-$(CONFIG_ARCH_R8A77995) += r8a77995-draak.dtb

3
arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi
View file

@ -23,6 +23,7 @@ xhci1: usb@ee040000 {
/delete-node/ mmu@febe0000;
/delete-node/ mmu@fe980000;
/delete-node/ mmu@fd950000;
/delete-node/ mmu@fd960000;
/delete-node/ mmu@fd970000;
@ -80,7 +81,7 @@ fcpvi2: fcp@fe9cf000 {
vspd3: vsp@fea38000 {
compatible = "renesas,vsp2";
reg = <0 0xfea38000 0 0x4000>;
reg = <0 0xfea38000 0 0x8000>;
interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 620>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;

194
arch/arm64/boot/dts/renesas/r8a7795.dtsi
View file

@ -41,6 +41,9 @@ a57_0: cpu@0 {
power-domains = <&sysc R8A7795_PD_CA57_CPU0>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
};
a57_1: cpu@1 {
@ -50,6 +53,9 @@ a57_1: cpu@1 {
power-domains = <&sysc R8A7795_PD_CA57_CPU1>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
};
a57_2: cpu@2 {
@ -59,6 +65,9 @@ a57_2: cpu@2 {
power-domains = <&sysc R8A7795_PD_CA57_CPU2>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
};
a57_3: cpu@3 {
@ -68,6 +77,9 @@ a57_3: cpu@3 {
power-domains = <&sysc R8A7795_PD_CA57_CPU3>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
};
a53_0: cpu@100 {
@ -77,6 +89,8 @@ a53_0: cpu@100 {
power-domains = <&sysc R8A7795_PD_CA53_CPU0>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
a53_1: cpu@101 {
@ -86,6 +100,8 @@ a53_1: cpu@101 {
power-domains = <&sysc R8A7795_PD_CA53_CPU1>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
a53_2: cpu@102 {
@ -95,6 +111,8 @@ a53_2: cpu@102 {
power-domains = <&sysc R8A7795_PD_CA53_CPU2>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
a53_3: cpu@103 {
@ -104,6 +122,8 @@ a53_3: cpu@103 {
power-domains = <&sysc R8A7795_PD_CA53_CPU3>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7795_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
L2_CA57: cache-controller-0 {
@ -165,11 +185,59 @@ can_clk: can {
clock-frequency = <0>;
};
/* External SCIF clock - to be overridden by boards that provide it */
scif_clk: scif {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
cluster0_opp: opp_table0 {
compatible = "operating-points-v2";
opp-shared;
opp-500000000 {
opp-hz = /bits/ 64 <500000000>;
opp-microvolt = <830000>;
clock-latency-ns = <300000>;
};
opp-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
opp-microvolt = <830000>;
clock-latency-ns = <300000>;
};
opp-1500000000 {
opp-hz = /bits/ 64 <1500000000>;
opp-microvolt = <830000>;
clock-latency-ns = <300000>;
opp-suspend;
};
opp-1600000000 {
opp-hz = /bits/ 64 <1600000000>;
opp-microvolt = <900000>;
clock-latency-ns = <300000>;
turbo-mode;
};
opp-1700000000 {
opp-hz = /bits/ 64 <1700000000>;
opp-microvolt = <960000>;
clock-latency-ns = <300000>;
turbo-mode;
};
};
cluster1_opp: opp_table1 {
compatible = "operating-points-v2";
opp-shared;
opp-800000000 {
opp-hz = /bits/ 64 <800000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1200000000 {
opp-hz = /bits/ 64 <1200000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
};
/* External PCIe clock - can be overridden by the board */
@ -208,6 +276,13 @@ psci {
method = "smc";
};
/* External SCIF clock - to be overridden by boards that provide it */
scif_clk: scif {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
soc: soc {
compatible = "simple-bus";
interrupt-parent = <&gic>;
@ -470,6 +545,15 @@ ipmmu_pv0: mmu@fd800000 {
status = "disabled";
};
ipmmu_pv1: mmu@fd950000 {
compatible = "renesas,ipmmu-r8a7795";
reg = <0 0xfd950000 0 0x1000>;
renesas,ipmmu-main = <&ipmmu_mm 7>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#iommu-cells = <1>;
status = "disabled";
};
ipmmu_pv2: mmu@fd960000 {
compatible = "renesas,ipmmu-r8a7795";
reg = <0 0xfd960000 0 0x1000>;
@ -798,7 +882,7 @@ avb: ethernet@e6800000 {
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 812>;
phy-mode = "rgmii-txid";
phy-mode = "rgmii";
iommus = <&ipmmu_ds0 16>;
#address-cells = <1>;
#size-cells = <0>;
@ -992,8 +1076,9 @@ hscif0: serial@e6540000 {
<&cpg CPG_CORE R8A7795_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x31>, <&dmac1 0x30>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x31>, <&dmac1 0x30>,
<&dmac2 0x31>, <&dmac2 0x30>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 520>;
status = "disabled";
@ -1009,8 +1094,9 @@ hscif1: serial@e6550000 {
<&cpg CPG_CORE R8A7795_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x33>, <&dmac1 0x32>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x33>, <&dmac1 0x32>,
<&dmac2 0x33>, <&dmac2 0x32>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 519>;
status = "disabled";
@ -1026,8 +1112,9 @@ hscif2: serial@e6560000 {
<&cpg CPG_CORE R8A7795_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x35>, <&dmac1 0x34>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x35>, <&dmac1 0x34>,
<&dmac2 0x35>, <&dmac2 0x34>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 518>;
status = "disabled";
@ -1138,8 +1225,9 @@ scif0: serial@e6e60000 {
<&cpg CPG_CORE R8A7795_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x51>, <&dmac1 0x50>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x51>, <&dmac1 0x50>,
<&dmac2 0x51>, <&dmac2 0x50>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 207>;
status = "disabled";
@ -1154,8 +1242,9 @@ scif1: serial@e6e68000 {
<&cpg CPG_CORE R8A7795_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x53>, <&dmac1 0x52>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x53>, <&dmac1 0x52>,
<&dmac2 0x53>, <&dmac2 0x52>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 206>;
status = "disabled";
@ -1170,8 +1259,9 @@ scif2: serial@e6e88000 {
<&cpg CPG_CORE R8A7795_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x13>, <&dmac1 0x12>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x13>, <&dmac1 0x12>,
<&dmac2 0x13>, <&dmac2 0x12>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 310>;
status = "disabled";
@ -1218,8 +1308,9 @@ scif5: serial@e6f30000 {
<&cpg CPG_CORE R8A7795_CLK_S3D1>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x5b>, <&dmac1 0x5a>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
<&dmac2 0x5b>, <&dmac2 0x5a>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 202>;
status = "disabled";
@ -1251,8 +1342,9 @@ i2c0: i2c@e6500000 {
clocks = <&cpg CPG_MOD 931>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 931>;
dmas = <&dmac1 0x91>, <&dmac1 0x90>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x91>, <&dmac1 0x90>,
<&dmac2 0x91>, <&dmac2 0x90>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@ -1267,8 +1359,9 @@ i2c1: i2c@e6508000 {
clocks = <&cpg CPG_MOD 930>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 930>;
dmas = <&dmac1 0x93>, <&dmac1 0x92>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x93>, <&dmac1 0x92>,
<&dmac2 0x93>, <&dmac2 0x92>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@ -1283,8 +1376,9 @@ i2c2: i2c@e6510000 {
clocks = <&cpg CPG_MOD 929>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 929>;
dmas = <&dmac1 0x95>, <&dmac1 0x94>;
dma-names = "tx", "rx";
dmas = <&dmac1 0x95>, <&dmac1 0x94>,
<&dmac2 0x95>, <&dmac2 0x94>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@ -2143,7 +2237,7 @@ fcpvi1: fcp@fe9bf000 {
vspd0: vsp@fea20000 {
compatible = "renesas,vsp2";
reg = <0 0xfea20000 0 0x4000>;
reg = <0 0xfea20000 0 0x8000>;
interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 623>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@ -2163,7 +2257,7 @@ fcpvd0: fcp@fea27000 {
vspd1: vsp@fea28000 {
compatible = "renesas,vsp2";
reg = <0 0xfea28000 0 0x4000>;
reg = <0 0xfea28000 0 0x8000>;
interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 622>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@ -2183,7 +2277,7 @@ fcpvd1: fcp@fea2f000 {
vspd2: vsp@fea30000 {
compatible = "renesas,vsp2";
reg = <0 0xfea30000 0 0x4000>;
reg = <0 0xfea30000 0 0x8000>;
interrupts = <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 621>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
@ -2320,9 +2414,9 @@ du_out_lvds0: endpoint {
tsc: thermal@e6198000 {
compatible = "renesas,r8a7795-thermal";
reg = <0 0xe6198000 0 0x68>,
<0 0xe61a0000 0 0x5c>,
<0 0xe61a8000 0 0x5c>;
reg = <0 0xe6198000 0 0x100>,
<0 0xe61a0000 0 0x100>,
<0 0xe61a8000 0 0x100>;
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
@ -2357,12 +2451,24 @@ sensor_thermal1: sensor-thermal1 {
thermal-sensors = <&tsc 0>;
trips {
sensor1_passive: sensor1-passive {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
sensor1_crit: sensor1-crit {
temperature = <120000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&sensor1_passive>;
cooling-device = <&a57_0 4 4>;
};
};
};
sensor_thermal2: sensor-thermal2 {
@ -2371,12 +2477,24 @@ sensor_thermal2: sensor-thermal2 {
thermal-sensors = <&tsc 1>;
trips {
sensor2_passive: sensor2-passive {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
sensor2_crit: sensor2-crit {
temperature = <120000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&sensor2_passive>;
cooling-device = <&a57_0 4 4>;
};
};
};
sensor_thermal3: sensor-thermal3 {
@ -2385,12 +2503,24 @@ sensor_thermal3: sensor-thermal3 {
thermal-sensors = <&tsc 2>;
trips {
sensor3_passive: sensor3-passive {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
sensor3_crit: sensor3-crit {
temperature = <120000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&sensor3_passive>;
cooling-device = <&a57_0 4 4>;
};
};
};
};

130
arch/arm64/boot/dts/renesas/r8a7796.dtsi
View file

@ -71,6 +71,9 @@ a57_0: cpu@0 {
power-domains = <&sysc R8A7796_PD_CA57_CPU0>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7796_CLK_Z>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
};
a57_1: cpu@1 {
@ -80,6 +83,9 @@ a57_1: cpu@1 {
power-domains = <&sysc R8A7796_PD_CA57_CPU1>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7796_CLK_Z>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
};
a53_0: cpu@100 {
@ -89,6 +95,8 @@ a53_0: cpu@100 {
power-domains = <&sysc R8A7796_PD_CA53_CPU0>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7796_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
a53_1: cpu@101 {
@ -98,6 +106,8 @@ a53_1: cpu@101 {
power-domains = <&sysc R8A7796_PD_CA53_CPU1>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7796_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
a53_2: cpu@102 {
@ -107,6 +117,8 @@ a53_2: cpu@102 {
power-domains = <&sysc R8A7796_PD_CA53_CPU2>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7796_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
a53_3: cpu@103 {
@ -116,6 +128,8 @@ a53_3: cpu@103 {
power-domains = <&sysc R8A7796_PD_CA53_CPU3>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
clocks =<&cpg CPG_CORE R8A7796_CLK_Z2>;
operating-points-v2 = <&cluster1_opp>;
};
L2_CA57: cache-controller-0 {
@ -147,6 +161,72 @@ extalr_clk: extalr {
clock-frequency = <0>;
};
cluster0_opp: opp_table0 {
compatible = "operating-points-v2";
opp-shared;
opp-500000000 {
opp-hz = /bits/ 64 <500000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1500000000 {
opp-hz = /bits/ 64 <1500000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1600000000 {
opp-hz = /bits/ 64 <1600000000>;
opp-microvolt = <900000>;
clock-latency-ns = <300000>;
turbo-mode;
};
opp-1700000000 {
opp-hz = /bits/ 64 <1700000000>;
opp-microvolt = <900000>;
clock-latency-ns = <300000>;
turbo-mode;
};
opp-1800000000 {
opp-hz = /bits/ 64 <1800000000>;
opp-microvolt = <960000>;
clock-latency-ns = <300000>;
turbo-mode;
};
};
cluster1_opp: opp_table1 {
compatible = "operating-points-v2";
opp-shared;
opp-800000000 {
opp-hz = /bits/ 64 <800000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1200000000 {
opp-hz = /bits/ 64 <1200000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
};
opp-1300000000 {
opp-hz = /bits/ 64 <1300000000>;
opp-microvolt = <820000>;
clock-latency-ns = <300000>;
turbo-mode;
};
};
/* External PCIe clock - can be overridden by the board */
pcie_bus_clk: pcie_bus {
compatible = "fixed-clock";
@ -894,7 +974,7 @@ avb: ethernet@e6800000 {
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
resets = <&cpg 812>;
phy-mode = "rgmii-txid";
phy-mode = "rgmii";
iommus = <&ipmmu_ds0 16>;
#address-cells = <1>;
#size-cells = <0>;
@ -1561,9 +1641,9 @@ sdhi3: sd@ee160000 {
tsc: thermal@e6198000 {
compatible = "renesas,r8a7796-thermal";
reg = <0 0xe6198000 0 0x68>,
<0 0xe61a0000 0 0x5c>,
<0 0xe61a8000 0 0x5c>;
reg = <0 0xe6198000 0 0x100>,
<0 0xe61a0000 0 0x100>,
<0 0xe61a8000 0 0x100>;
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
@ -1839,7 +1919,7 @@ fcpvi0: fcp@fe9af000 {
vspd0: vsp@fea20000 {
compatible = "renesas,vsp2";
reg = <0 0xfea20000 0 0x4000>;
reg = <0 0xfea20000 0 0x8000>;
interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 623>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
@ -1859,7 +1939,7 @@ fcpvd0: fcp@fea27000 {
vspd1: vsp@fea28000 {
compatible = "renesas,vsp2";
reg = <0 0xfea28000 0 0x4000>;
reg = <0 0xfea28000 0 0x8000>;
interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 622>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
@ -1879,7 +1959,7 @@ fcpvd1: fcp@fea2f000 {
vspd2: vsp@fea30000 {
compatible = "renesas,vsp2";
reg = <0 0xfea30000 0 0x4000>;
reg = <0 0xfea30000 0 0x8000>;
interrupts = <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 621>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
@ -1998,12 +2078,24 @@ sensor_thermal1: sensor-thermal1 {
thermal-sensors = <&tsc 0>;
trips {
sensor1_passive: sensor1-passive {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
sensor1_crit: sensor1-crit {
temperature = <120000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&sensor1_passive>;
cooling-device = <&a57_0 5 5>;
};
};
};
sensor_thermal2: sensor-thermal2 {
@ -2012,12 +2104,24 @@ sensor_thermal2: sensor-thermal2 {
thermal-sensors = <&tsc 1>;
trips {
sensor2_passive: sensor2-passive {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
sensor2_crit: sensor2-crit {
temperature = <120000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&sensor2_passive>;
cooling-device = <&a57_0 5 5>;
};
};
};
sensor_thermal3: sensor-thermal3 {
@ -2026,12 +2130,24 @@ sensor_thermal3: sensor-thermal3 {
thermal-sensors = <&tsc 2>;
trips {
sensor3_passive: sensor3-passive {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
sensor3_crit: sensor3-crit {
temperature = <120000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&sensor3_passive>;
cooling-device = <&a57_0 5 5>;
};
};
};
};

21
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts Normal file
View file

@ -0,0 +1,21 @@
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the Salvator-X board with R-Car M3-N
*
* Copyright (C) 2018 Jacopo Mondi <jacopo+renesas@jmondi.org>
*/
/dts-v1/;
#include "r8a77965.dtsi"
#include "salvator-x.dtsi"
/ {
model = "Renesas Salvator-X board based on r8a77965";
compatible = "renesas,salvator-x", "renesas,r8a77965";
memory@48000000 {
device_type = "memory";
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x78000000>;
};
};

21
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts Normal file
View file

@ -0,0 +1,21 @@
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the Salvator-X 2nd version board with R-Car M3-N
*
* Copyright (C) 2017 Renesas Electronics Corp.
*/
/dts-v1/;
#include "r8a77965.dtsi"
#include "salvator-xs.dtsi"
/ {
model = "Renesas Salvator-X 2nd version board based on r8a77965";
compatible = "renesas,salvator-xs", "renesas,r8a77965";
memory@48000000 {
device_type = "memory";
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x78000000>;
};
};

878
arch/arm64/boot/dts/renesas/r8a77965.dtsi Normal file
View file

@ -0,0 +1,878 @@
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the r8a77965 SoC
*
* Copyright (C) 2018 Jacopo Mondi <jacopo+renesas@jmondi.org>
*
* Based on r8a7796.dtsi
* Copyright (C) 2016 Renesas Electronics Corp.
*/
#include <dt-bindings/clock/renesas-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#define CPG_AUDIO_CLK_I 10
/ {
compatible = "renesas,r8a77965";
#address-cells = <2>;
#size-cells = <2>;
aliases {
i2c7 = &i2c_dvfs;
};
psci {
compatible = "arm,psci-1.0", "arm,psci-0.2";
method = "smc";
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
a57_0: cpu@0 {
compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x0>;
device_type = "cpu";
power-domains = <&sysc 0>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
a57_1: cpu@1 {
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x1>;
device_type = "cpu";
power-domains = <&sysc 1>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
L2_CA57: cache-controller-0 {
compatible = "cache";
power-domains = <&sysc 12>;
cache-unified;
cache-level = <2>;
};
};
extal_clk: extal {
compatible = "fixed-clock";
#clock-cells = <0>;
/* This value must be overridden by the board */
clock-frequency = <0>;
};
extalr_clk: extalr {
compatible = "fixed-clock";
#clock-cells = <0>;
/* This value must be overridden by the board */
clock-frequency = <0>;
};
/*
* The external audio clocks are configured as 0 Hz fixed frequency
* clocks by default.
* Boards that provide audio clocks should override them.
*/
audio_clk_a: audio_clk_a {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
audio_clk_b: audio_clk_b {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
audio_clk_c: audio_clk_c {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
/* External CAN clock - to be overridden by boards that provide it */
can_clk: can {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
/* External SCIF clock - to be overridden by boards that provide it */
scif_clk: scif {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
/* External PCIe clock - can be overridden by the board */
pcie_bus_clk: pcie_bus {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
/* External USB clocks - can be overridden by the board */
usb3s0_clk: usb3s0 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
usb_extal_clk: usb_extal {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
timer {
compatible = "arm,armv8-timer";
interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
};
pmu_a57 {
compatible = "arm,cortex-a57-pmu";
interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
<&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&a57_0>,
<&a57_1>;
};
soc {
compatible = "simple-bus";
interrupt-parent = <&gic>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
gic: interrupt-controller@f1010000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
#address-cells = <0>;
interrupt-controller;
reg = <0x0 0xf1010000 0 0x1000>,
<0x0 0xf1020000 0 0x20000>,
<0x0 0xf1040000 0 0x20000>,
<0x0 0xf1060000 0 0x20000>;
interrupts = <GIC_PPI 9
(GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&cpg CPG_MOD 408>;
clock-names = "clk";
power-domains = <&sysc 32>;
resets = <&cpg 408>;
};
pfc: pin-controller@e6060000 {
compatible = "renesas,pfc-r8a77965";
reg = <0 0xe6060000 0 0x50c>;
};
cpg: clock-controller@e6150000 {
compatible = "renesas,r8a77965-cpg-mssr";
reg = <0 0xe6150000 0 0x1000>;
clocks = <&extal_clk>, <&extalr_clk>;
clock-names = "extal", "extalr";
#clock-cells = <2>;
#power-domain-cells = <0>;
#reset-cells = <1>;
};
rst: reset-controller@e6160000 {
compatible = "renesas,r8a77965-rst";
reg = <0 0xe6160000 0 0x0200>;
};
prr: chipid@fff00044 {
compatible = "renesas,prr";
reg = <0 0xfff00044 0 4>;
};
sysc: system-controller@e6180000 {
compatible = "renesas,r8a77965-sysc";
reg = <0 0xe6180000 0 0x0400>;
#power-domain-cells = <1>;
};
gpio0: gpio@e6050000 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6050000 0 0x50>;
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 0 16>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 912>;
power-domains = <&sysc 32>;
resets = <&cpg 912>;
};
gpio1: gpio@e6051000 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6051000 0 0x50>;
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 32 29>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 911>;
power-domains = <&sysc 32>;
resets = <&cpg 911>;
};
gpio2: gpio@e6052000 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6052000 0 0x50>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 64 15>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 910>;
power-domains = <&sysc 32>;
resets = <&cpg 910>;
};
gpio3: gpio@e6053000 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6053000 0 0x50>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 96 16>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 909>;
power-domains = <&sysc 32>;
resets = <&cpg 909>;
};
gpio4: gpio@e6054000 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6054000 0 0x50>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 128 18>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 908>;
power-domains = <&sysc 32>;
resets = <&cpg 908>;
};
gpio5: gpio@e6055000 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6055000 0 0x50>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 160 26>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 907>;
power-domains = <&sysc 32>;
resets = <&cpg 907>;
};
gpio6: gpio@e6055400 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6055400 0 0x50>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 192 32>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 906>;
power-domains = <&sysc 32>;
resets = <&cpg 906>;
};
gpio7: gpio@e6055800 {
compatible = "renesas,gpio-r8a77965",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6055800 0 0x50>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 224 4>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 905>;
power-domains = <&sysc 32>;
resets = <&cpg 905>;
};
intc_ex: interrupt-controller@e61c0000 {
compatible = "renesas,intc-ex-r8a77965", "renesas,irqc";
#interrupt-cells = <2>;
interrupt-controller;
reg = <0 0xe61c0000 0 0x200>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 407>;
power-domains = <&sysc 32>;
resets = <&cpg 407>;
};
dmac0: dma-controller@e6700000 {
compatible = "renesas,dmac-r8a77965",
"renesas,rcar-dmac";
reg = <0 0xe6700000 0 0x10000>;
interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "error",
"ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 219>;
clock-names = "fck";
power-domains = <&sysc 32>;
resets = <&cpg 219>;
#dma-cells = <1>;
dma-channels = <16>;
};
dmac1: dma-controller@e7300000 {
compatible = "renesas,dmac-r8a77965",
"renesas,rcar-dmac";
reg = <0 0xe7300000 0 0x10000>;
interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "error",
"ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 218>;
clock-names = "fck";
power-domains = <&sysc 32>;
resets = <&cpg 218>;
#dma-cells = <1>;
dma-channels = <16>;
};
dmac2: dma-controller@e7310000 {
compatible = "renesas,dmac-r8a77965",
"renesas,rcar-dmac";
reg = <0 0xe7310000 0 0x10000>;
interrupts = <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "error",
"ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 217>;
clock-names = "fck";
power-domains = <&sysc 32>;
resets = <&cpg 217>;
#dma-cells = <1>;
dma-channels = <16>;
};
scif0: serial@e6e60000 {
compatible = "renesas,scif-r8a77965",
"renesas,rcar-gen3-scif", "renesas,scif";
reg = <0 0xe6e60000 0 64>;
interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 207>,
<&cpg CPG_CORE 20>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x51>, <&dmac1 0x50>,
<&dmac2 0x51>, <&dmac2 0x50>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 207>;
status = "disabled";
};
scif1: serial@e6e68000 {
compatible = "renesas,scif-r8a77965",
"renesas,rcar-gen3-scif", "renesas,scif";
reg = <0 0xe6e68000 0 64>;
interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 206>,
<&cpg CPG_CORE 20>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x53>, <&dmac1 0x52>,
<&dmac2 0x53>, <&dmac2 0x52>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 206>;
status = "disabled";
};
scif2: serial@e6e88000 {
compatible = "renesas,scif-r8a77965",
"renesas,rcar-gen3-scif", "renesas,scif";
reg = <0 0xe6e88000 0 64>;
interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 310>,
<&cpg CPG_CORE 20>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
power-domains = <&sysc 32>;
resets = <&cpg 310>;
status = "disabled";
};
scif3: serial@e6c50000 {
compatible = "renesas,scif-r8a77965",
"renesas,rcar-gen3-scif", "renesas,scif";
reg = <0 0xe6c50000 0 64>;
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 204>,
<&cpg CPG_CORE 20>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x57>, <&dmac0 0x56>;
dma-names = "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 204>;
status = "disabled";
};
scif4: serial@e6c40000 {
compatible = "renesas,scif-r8a77965",
"renesas,rcar-gen3-scif", "renesas,scif";
reg = <0 0xe6c40000 0 64>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 203>,
<&cpg CPG_CORE 20>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x59>, <&dmac0 0x58>;
dma-names = "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 203>;
status = "disabled";
};
scif5: serial@e6f30000 {
compatible = "renesas,scif-r8a77965",
"renesas,rcar-gen3-scif", "renesas,scif";
reg = <0 0xe6f30000 0 64>;
interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 202>,
<&cpg CPG_CORE 20>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
<&dmac2 0x5b>, <&dmac2 0x5a>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 202>;
status = "disabled";
};
avb: ethernet@e6800000 {
compatible = "renesas,etheravb-r8a77965",
"renesas,etheravb-rcar-gen3";
reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15",
"ch16", "ch17", "ch18", "ch19",
"ch20", "ch21", "ch22", "ch23",
"ch24";
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc 32>;
resets = <&cpg 812>;
phy-mode = "rgmii";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
csi20: csi2@fea80000 {
reg = <0 0xfea80000 0 0x10000>;
/* placeholder */
ports {
#address-cells = <1>;
#size-cells = <0>;
};
};
csi40: csi2@feaa0000 {
reg = <0 0xfeaa0000 0 0x10000>;
/* placeholder */
ports {
#address-cells = <1>;
#size-cells = <0>;
};
};
vin0: video@e6ef0000 {
reg = <0 0xe6ef0000 0 0x1000>;
/* placeholder */
};
vin1: video@e6ef1000 {
reg = <0 0xe6ef1000 0 0x1000>;
/* placeholder */
};
vin2: video@e6ef2000 {
reg = <0 0xe6ef2000 0 0x1000>;
/* placeholder */
};
vin3: video@e6ef3000 {
reg = <0 0xe6ef3000 0 0x1000>;
/* placeholder */
};
vin4: video@e6ef4000 {
reg = <0 0xe6ef4000 0 0x1000>;
/* placeholder */
};
vin5: video@e6ef5000 {
reg = <0 0xe6ef5000 0 0x1000>;
/* placeholder */
};
vin6: video@e6ef6000 {
reg = <0 0xe6ef6000 0 0x1000>;
/* placeholder */
};
vin7: video@e6ef7000 {
reg = <0 0xe6ef7000 0 0x1000>;
/* placeholder */
};
ohci0: usb@ee080000 {
reg = <0 0xee080000 0 0x100>;
/* placeholder */
};
ehci0: usb@ee080100 {
reg = <0 0xee080100 0 0x100>;
/* placeholder */
};
usb2_phy0: usb-phy@ee080200 {
reg = <0 0xee080200 0 0x700>;
/* placeholder */
};
usb2_phy1: usb-phy@ee0a0200 {
reg = <0 0xee0a0200 0 0x700>;
/* placeholder */
};
ohci1: usb@ee0a0000 {
reg = <0 0xee0a0000 0 0x100>;
/* placeholder */
};
ehci1: usb@ee0a0100 {
reg = <0 0xee0a0100 0 0x100>;
/* placeholder */
};
i2c0: i2c@e6500000 {
reg = <0 0xe6500000 0 0x40>;
/* placeholder */
};
i2c1: i2c@e6508000 {
reg = <0 0xe6508000 0 0x40>;
/* placeholder */
};
i2c2: i2c@e6510000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe6510000 0 0x40>;
/* placeholder */
};
i2c3: i2c@e66d0000 {
reg = <0 0xe66d0000 0 0x40>;
/* placeholder */
};
i2c4: i2c@e66d8000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0 0xe66d8000 0 0x40>;
/* placeholder */
};
i2c5: i2c@e66e0000 {
reg = <0 0xe66e0000 0 0x40>;
/* placeholder */
};
i2c6: i2c@e66e8000 {
reg = <0 0xe66e8000 0 0x40>;
/* placeholder */
};
i2c_dvfs: i2c@e60b0000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "renesas,iic-r8a77965",
"renesas,rcar-gen3-iic",
"renesas,rmobile-iic";
reg = <0 0xe60b0000 0 0x425>;
interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 926>;
power-domains = <&sysc 32>;
resets = <&cpg 926>;
dmas = <&dmac0 0x11>, <&dmac0 0x10>;
dma-names = "tx", "rx";
status = "disabled";
};
pwm0: pwm@e6e30000 {
reg = <0 0xe6e30000 0 8>;
/* placeholder */
};
pwm1: pwm@e6e31000 {
reg = <0 0xe6e31000 0 8>;
#pwm-cells = <2>;
/* placeholder */
};
pwm2: pwm@e6e32000 {
reg = <0 0xe6e32000 0 8>;
/* placeholder */
};
pwm3: pwm@e6e33000 {
reg = <0 0xe6e33000 0 8>;
/* placeholder */
};
pwm4: pwm@e6e34000 {
reg = <0 0xe6e34000 0 8>;
/* placeholder */
};
pwm5: pwm@e6e35000 {
reg = <0 0xe6e35000 0 8>;
/* placeholder */
};
pwm6: pwm@e6e36000 {
reg = <0 0xe6e36000 0 8>;
/* placeholder */
};
du: display@feb00000 {
reg = <0 0xfeb00000 0 0x80000>,
<0 0xfeb90000 0 0x14>;
/* placeholder */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
du_out_rgb: endpoint {
};
};
port@1 {
reg = <1>;
du_out_hdmi0: endpoint {
};
};
port@2 {
reg = <2>;
du_out_lvds0: endpoint {
};
};
};
};
hsusb: usb@e6590000 {
reg = <0 0xe6590000 0 0x100>;
/* placeholder */
};
pciec0: pcie@fe000000 {
reg = <0 0xfe000000 0 0x80000>;
/* placeholder */
};
pciec1: pcie@ee800000 {
reg = <0 0xee800000 0 0x80000>;
/* placeholder */
};
rcar_sound: sound@ec500000 {
reg = <0 0xec500000 0 0x1000>, /* SCU */
<0 0xec5a0000 0 0x100>, /* ADG */
<0 0xec540000 0 0x1000>, /* SSIU */
<0 0xec541000 0 0x280>, /* SSI */
<0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/
/* placeholder */
rcar_sound,dvc {
dvc0: dvc-0 {
};
dvc1: dvc-1 {
};
};
rcar_sound,src {
src0: src-0 {
};
src1: src-1 {
};
};
rcar_sound,ssi {
ssi0: ssi-0 {
};
ssi1: ssi-1 {
};
};
};
sdhi0: sd@ee100000 {
reg = <0 0xee100000 0 0x2000>;
/* placeholder */
};
sdhi1: sd@ee120000 {
reg = <0 0xee120000 0 0x2000>;
/* placeholder */
};
sdhi2: sd@ee140000 {
reg = <0 0xee140000 0 0x2000>;
/* placeholder */
};
sdhi3: sd@ee160000 {
reg = <0 0xee160000 0 0x2000>;
/* placeholder */
};
usb3_phy0: usb-phy@e65ee000 {
reg = <0 0xe65ee000 0 0x90>;
#phy-cells = <0>;
/* placeholder */
};
usb3_peri0: usb@ee020000 {
reg = <0 0xee020000 0 0x400>;
/* placeholder */
};
xhci0: usb@ee000000 {
reg = <0 0xee000000 0 0xc00>;
/* placeholder */
};
wdt0: watchdog@e6020000 {
reg = <0 0xe6020000 0 0x0c>;
/* placeholder */
};
};
};

33
arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
View file

@ -36,11 +36,14 @@ memory@48000000 {
&avb {
renesas,no-ether-link;
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
status = "okay";
phy0: ethernet-phy@0 {
rxc-skew-ps = <1500>;
reg = <0>;
interrupt-parent = <&gpio1>;
interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
};
};
@ -52,11 +55,41 @@ &extalr_clk {
clock-frequency = <32768>;
};
&i2c0 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
status = "okay";
clock-frequency = <400000>;
io_expander: gpio@20 {
compatible = "onnn,pca9654";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
};
};
&pfc {
i2c0_pins: i2c0 {
groups = "i2c0";
function = "i2c0";
};
scif0_pins: scif0 {
groups = "scif0_data";
function = "scif0";
};
};
&rwdt {
timeout-sec = <60>;
status = "okay";
};
&scif0 {
pinctrl-0 = <&scif0_pins>;
pinctrl-names = "default";
status = "okay";
};

11
arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
View file

@ -34,6 +34,7 @@ memory@48000000 {
&avb {
renesas,no-ether-link;
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
status = "okay";
phy0: ethernet-phy@0 {
@ -50,6 +51,16 @@ &extalr_clk {
clock-frequency = <32768>;
};
&pfc {
scif0_pins: scif0 {
groups = "scif0_data";
function = "scif0";
};
};
&scif0 {
pinctrl-0 = <&scif0_pins>;
pinctrl-names = "default";
status = "okay";
};

218
arch/arm64/boot/dts/renesas/r8a77970.dtsi
View file

@ -19,9 +19,12 @@ / {
#address-cells = <2>;
#size-cells = <2>;
psci {
compatible = "arm,psci-1.0", "arm,psci-0.2";
method = "smc";
aliases {
i2c0 = &i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
i2c3 = &i2c3;
i2c4 = &i2c4;
};
cpus {
@ -60,6 +63,11 @@ extalr_clk: extalr {
clock-frequency = <0>;
};
psci {
compatible = "arm,psci-1.0", "arm,psci-0.2";
method = "smc";
};
/* External SCIF clock - to be overridden by boards that provide it */
scif_clk: scif {
compatible = "fixed-clock";
@ -92,18 +100,6 @@ gic: interrupt-controller@f1010000 {
resets = <&cpg 408>;
};
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>;
};
rwdt: watchdog@e6020000 {
compatible = "renesas,r8a77970-wdt",
"renesas,rcar-gen3-wdt";
@ -178,6 +174,101 @@ ipmmu_mm: mmu@e67b0000 {
#iommu-cells = <1>;
};
pfc: pin-controller@e6060000 {
compatible = "renesas,pfc-r8a77970";
reg = <0 0xe6060000 0 0x504>;
};
gpio0: gpio@e6050000 {
compatible = "renesas,gpio-r8a77970",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6050000 0 0x50>;
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 0 22>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 912>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 912>;
};
gpio1: gpio@e6051000 {
compatible = "renesas,gpio-r8a77970",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6051000 0 0x50>;
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 32 28>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 911>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 911>;
};
gpio2: gpio@e6052000 {
compatible = "renesas,gpio-r8a77970",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6052000 0 0x50>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 64 17>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 910>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 910>;
};
gpio3: gpio@e6053000 {
compatible = "renesas,gpio-r8a77970",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6053000 0 0x50>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 96 17>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 909>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 909>;
};
gpio4: gpio@e6054000 {
compatible = "renesas,gpio-r8a77970",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6054000 0 0x50>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 128 6>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 908>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 908>;
};
gpio5: gpio@e6055000 {
compatible = "renesas,gpio-r8a77970",
"renesas,rcar-gen3-gpio";
reg = <0 0xe6055000 0 0x50>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
#gpio-cells = <2>;
gpio-controller;
gpio-ranges = <&pfc 0 160 15>;
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 907>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 907>;
};
intc_ex: interrupt-controller@e61c0000 {
compatible = "renesas,intc-ex-r8a77970", "renesas,irqc";
#interrupt-cells = <2>;
@ -255,6 +346,91 @@ GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH
<&ipmmu_ds1 22>, <&ipmmu_ds1 23>;
};
i2c0: i2c@e6500000 {
compatible = "renesas,i2c-r8a77970",
"renesas,rcar-gen3-i2c";
reg = <0 0xe6500000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 931>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 931>;
dmas = <&dmac1 0x91>, <&dmac1 0x90>,
<&dmac2 0x91>, <&dmac2 0x90>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c1: i2c@e6508000 {
compatible = "renesas,i2c-r8a77970",
"renesas,rcar-gen3-i2c";
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 930>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 930>;
dmas = <&dmac1 0x93>, <&dmac1 0x92>,
<&dmac2 0x93>, <&dmac2 0x92>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c2: i2c@e6510000 {
compatible = "renesas,i2c-r8a77970",
"renesas,rcar-gen3-i2c";
reg = <0 0xe6510000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 929>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 929>;
dmas = <&dmac1 0x95>, <&dmac1 0x94>,
<&dmac2 0x95>, <&dmac2 0x94>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c3: i2c@e66d0000 {
compatible = "renesas,i2c-r8a77970",
"renesas,rcar-gen3-i2c";
reg = <0 0xe66d0000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 928>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 928>;
dmas = <&dmac1 0x97>, <&dmac1 0x96>,
<&dmac2 0x97>, <&dmac2 0x96>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c4: i2c@e66d8000 {
compatible = "renesas,i2c-r8a77970",
"renesas,rcar-gen3-i2c";
reg = <0 0xe66d8000 0 0x40>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 927>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 927>;
dmas = <&dmac1 0x99>, <&dmac1 0x98>,
<&dmac2 0x99>, <&dmac2 0x98>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
hscif0: serial@e6540000 {
compatible = "renesas,hscif-r8a77970",
"renesas,rcar-gen3-hscif",
@ -400,7 +576,7 @@ scif4: serial@e6c40000 {
avb: ethernet@e6800000 {
compatible = "renesas,etheravb-r8a77970",
"renesas,etheravb-rcar-gen3";
reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
reg = <0 0xe6800000 0 0x800>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
@ -436,10 +612,18 @@ avb: ethernet@e6800000 {
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
resets = <&cpg 812>;
phy-mode = "rgmii-id";
phy-mode = "rgmii";
iommus = <&ipmmu_rt 3>;
#address-cells = <1>;
#size-cells = <0>;
};
};
timer {
compatible = "arm,armv8-timer";
interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
};
};

58
arch/arm64/boot/dts/renesas/r8a77980-condor.dts Normal file
View file

@ -0,0 +1,58 @@
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the Condor board
*
* Copyright (C) 2018 Renesas Electronics Corp.
* Copyright (C) 2018 Cogent Embedded, Inc.
*/
/dts-v1/;
#include "r8a77980.dtsi"
/ {
model = "Renesas Condor board based on r8a77980";
compatible = "renesas,condor", "renesas,r8a77980";
aliases {
serial0 = &scif0;
ethernet0 = &avb;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@48000000 {
device_type = "memory";
/* first 128MB is reserved for secure area. */
reg = <0 0x48000000 0 0x78000000>;
};
};
&avb {
phy-mode = "rgmii-id";
phy-handle = <&phy0>;
renesas,no-ether-link;
status = "okay";
phy0: ethernet-phy@0 {
rxc-skew-ps = <1500>;
reg = <0>;
};
};
&extal_clk {
clock-frequency = <16666666>;
};
&extalr_clk {
clock-frequency = <32768>;
};
&scif0 {
status = "okay";
};
&scif_clk {
clock-frequency = <14745600>;
};

385
arch/arm64/boot/dts/renesas/r8a77980.dtsi Normal file
View file

@ -0,0 +1,385 @@
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the r8a77980 SoC
*
* Copyright (C) 2018 Renesas Electronics Corp.
* Copyright (C) 2018 Cogent Embedded, Inc.
*/
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/renesas-cpg-mssr.h>
/ {
compatible = "renesas,r8a77980";
#address-cells = <2>;
#size-cells = <2>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
a53_0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0>;
clocks = <&cpg CPG_CORE 0>;
power-domains = <&sysc 5>;
next-level-cache = <&L2_CA53>;
enable-method = "psci";
};
L2_CA53: cache-controller {
compatible = "cache";
power-domains = <&sysc 21>;
cache-unified;
cache-level = <2>;
};
};
extal_clk: extal {
compatible = "fixed-clock";
#clock-cells = <0>;
/* This value must be overridden by the board */
clock-frequency = <0>;
};
extalr_clk: extalr {
compatible = "fixed-clock";
#clock-cells = <0>;
/* This value must be overridden by the board */
clock-frequency = <0>;
};
psci {
compatible = "arm,psci-1.0", "arm,psci-0.2";
method = "smc";
};
/* External SCIF clock - to be overridden by boards that provide it */
scif_clk: scif {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
soc {
compatible = "simple-bus";
interrupt-parent = <&gic>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
cpg: clock-controller@e6150000 {
compatible = "renesas,r8a77980-cpg-mssr";
reg = <0 0xe6150000 0 0x1000>;
clocks = <&extal_clk>, <&extalr_clk>;
clock-names = "extal", "extalr";
#clock-cells = <2>;
#power-domain-cells = <0>;
#reset-cells = <1>;
};
rst: reset-controller@e6160000 {
compatible = "renesas,r8a77980-rst";
reg = <0 0xe6160000 0 0x200>;
};
sysc: system-controller@e6180000 {
compatible = "renesas,r8a77980-sysc";
reg = <0 0xe6180000 0 0x440>;
#power-domain-cells = <1>;
};
hscif0: serial@e6540000 {
compatible = "renesas,hscif-r8a77980",
"renesas,rcar-gen3-hscif",
"renesas,hscif";
reg = <0 0xe6540000 0 0x60>;
interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 520>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x31>, <&dmac1 0x30>,
<&dmac2 0x31>, <&dmac2 0x30>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 520>;
status = "disabled";
};
hscif1: serial@e6550000 {
compatible = "renesas,hscif-r8a77980",
"renesas,rcar-gen3-hscif",
"renesas,hscif";
reg = <0 0xe6550000 0 0x60>;
interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 519>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x33>, <&dmac1 0x32>,
<&dmac2 0x33>, <&dmac2 0x32>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 519>;
status = "disabled";
};
hscif2: serial@e6560000 {
compatible = "renesas,hscif-r8a77980",
"renesas,rcar-gen3-hscif",
"renesas,hscif";
reg = <0 0xe6560000 0 0x60>;
interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 518>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x35>, <&dmac1 0x34>,
<&dmac2 0x35>, <&dmac2 0x34>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 518>;
status = "disabled";
};
hscif3: serial@e66a0000 {
compatible = "renesas,hscif-r8a77980",
"renesas,rcar-gen3-hscif",
"renesas,hscif";
reg = <0 0xe66a0000 0 0x60>;
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 517>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x37>, <&dmac1 0x36>,
<&dmac2 0x37>, <&dmac2 0x36>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 517>;
status = "disabled";
};
avb: ethernet@e6800000 {
compatible = "renesas,etheravb-r8a77980",
"renesas,etheravb-rcar-gen3";
reg = <0 0xe6800000 0 0x800>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15",
"ch16", "ch17", "ch18", "ch19",
"ch20", "ch21", "ch22", "ch23",
"ch24";
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc 32>;
resets = <&cpg 812>;
phy-mode = "rgmii";
#address-cells = <1>;
#size-cells = <0>;
};
scif0: serial@e6e60000 {
compatible = "renesas,scif-r8a77980",
"renesas,rcar-gen3-scif",
"renesas,scif";
reg = <0 0xe6e60000 0 0x40>;
interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 207>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x51>, <&dmac1 0x50>,
<&dmac2 0x51>, <&dmac2 0x50>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 207>;
status = "disabled";
};
scif1: serial@e6e68000 {
compatible = "renesas,scif-r8a77980",
"renesas,rcar-gen3-scif",
"renesas,scif";
reg = <0 0xe6e68000 0 0x40>;
interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 206>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x53>, <&dmac1 0x52>,
<&dmac2 0x53>, <&dmac2 0x52>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 206>;
status = "disabled";
};
scif3: serial@e6c50000 {
compatible = "renesas,scif-r8a77980",
"renesas,rcar-gen3-scif",
"renesas,scif";
reg = <0 0xe6c50000 0 0x40>;
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 204>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x57>, <&dmac1 0x56>,
<&dmac2 0x57>, <&dmac2 0x56>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 204>;
status = "disabled";
};
scif4: serial@e6c40000 {
compatible = "renesas,scif-r8a77980",
"renesas,rcar-gen3-scif",
"renesas,scif";
reg = <0 0xe6c40000 0 0x40>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 203>,
<&cpg CPG_CORE 19>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x59>, <&dmac1 0x58>,
<&dmac2 0x59>, <&dmac2 0x58>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc 32>;
resets = <&cpg 203>;
status = "disabled";
};
dmac1: dma-controller@e7300000 {
compatible = "renesas,dmac-r8a77980",
"renesas,rcar-dmac";
reg = <0 0xe7300000 0 0x10000>;
interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "error",
"ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 218>;
clock-names = "fck";
power-domains = <&sysc 32>;
resets = <&cpg 218>;
#dma-cells = <1>;
dma-channels = <16>;
};
dmac2: dma-controller@e7310000 {
compatible = "renesas,dmac-r8a77980",
"renesas,rcar-dmac";
reg = <0 0xe7310000 0 0x10000>;
interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "error",
"ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 217>;
clock-names = "fck";
power-domains = <&sysc 32>;
resets = <&cpg 217>;
#dma-cells = <1>;
dma-channels = <16>;
};
gic: interrupt-controller@f1010000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
#address-cells = <0>;
interrupt-controller;
reg = <0x0 0xf1010000 0 0x1000>,
<0x0 0xf1020000 0 0x20000>,
<0x0 0xf1040000 0 0x20000>,
<0x0 0xf1060000 0 0x20000>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&cpg CPG_MOD 408>;
clock-names = "clk";
power-domains = <&sysc 32>;
resets = <&cpg 408>;
};
prr: chipid@fff00044 {
compatible = "renesas,prr";
reg = <0 0xfff00044 0 4>;
};
};
timer {
compatible = "arm,armv8-timer";
interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) |
IRQ_TYPE_LEVEL_LOW)>;
};
};

124
arch/arm64/boot/dts/renesas/r8a77995-draak.dts
View file

@ -27,11 +27,61 @@ chosen {
stdout-path = "serial0:115200n8";
};
vga {
compatible = "vga-connector";
port {
vga_in: endpoint {
remote-endpoint = <&adv7123_out>;
};
};
};
vga-encoder {
compatible = "adi,adv7123";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7123_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7123_out: endpoint {
remote-endpoint = <&vga_in>;
};
};
};
};
memory@48000000 {
device_type = "memory";
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x18000000>;
};
reg_1p8v: regulator0 {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
reg_3p3v: regulator1 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
};
&extal_clk {
@ -46,6 +96,21 @@ mux {
};
};
du_pins: du {
groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
function = "du";
};
i2c0_pins: i2c0 {
groups = "i2c0";
function = "i2c0";
};
i2c1_pins: i2c1 {
groups = "i2c1";
function = "i2c1";
};
pwm0_pins: pwm0 {
groups = "pwm0_c";
function = "pwm0";
@ -61,12 +126,56 @@ scif2_pins: scif2 {
function = "scif2";
};
sdhi2_pins: sd2 {
groups = "mmc_data8", "mmc_ctrl";
function = "mmc";
power-source = <1800>;
};
sdhi2_pins_uhs: sd2_uhs {
groups = "mmc_data8", "mmc_ctrl";
function = "mmc";
power-source = <1800>;
};
usb0_pins: usb0 {
groups = "usb0";
function = "usb0";
};
};
&i2c0 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
status = "okay";
eeprom@50 {
compatible = "rohm,br24t01", "atmel,24c01";
reg = <0x50>;
pagesize = <8>;
};
};
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
pinctrl-names = "default";
status = "okay";
};
&du {
pinctrl-0 = <&du_pins>;
pinctrl-names = "default";
status = "okay";
ports {
port@0 {
endpoint {
remote-endpoint = <&adv7123_in>;
};
};
};
};
&ehci0 {
status = "okay";
};
@ -80,6 +189,7 @@ &avb {
pinctrl-names = "default";
renesas,no-ether-link;
phy-handle = <&phy0>;
phy-mode = "rgmii-txid";
status = "okay";
phy0: ethernet-phy@0 {
@ -97,6 +207,20 @@ &scif2 {
status = "okay";
};
&sdhi2 {
/* used for on-board eMMC */
pinctrl-0 = <&sdhi2_pins>;
pinctrl-1 = <&sdhi2_pins_uhs>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <&reg_3p3v>;
vqmmc-supply = <&reg_1p8v>;
bus-width = <8>;
mmc-hs200-1_8v;
non-removable;
status = "okay";
};
&usb2_phy0 {
pinctrl-0 = <&usb0_pins>;
pinctrl-names = "default";

193
arch/arm64/boot/dts/renesas/r8a77995.dtsi
View file

@ -58,6 +58,11 @@ can_clk: can {
clock-frequency = <0>;
};
pmu_a53 {
compatible = "arm,cortex-a53-pmu";
interrupts-extended = <&gic GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
};
scif_clk: scif {
compatible = "fixed-clock";
#clock-cells = <0>;
@ -88,18 +93,6 @@ gic: interrupt-controller@f1010000 {
resets = <&cpg 408>;
};
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13
(GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14
(GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11
(GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10
(GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
};
rwdt: watchdog@e6020000 {
compatible = "renesas,r8a77995-wdt",
"renesas,rcar-gen3-wdt";
@ -110,11 +103,6 @@ rwdt: watchdog@e6020000 {
status = "disabled";
};
pmu_a53 {
compatible = "arm,cortex-a53-pmu";
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
};
ipmmu_vi0: mmu@febd0000 {
compatible = "renesas,ipmmu-r8a77995";
reg = <0 0xfebd0000 0 0x1000>;
@ -488,7 +476,7 @@ channel1 {
avb: ethernet@e6800000 {
compatible = "renesas,etheravb-r8a77995",
"renesas,etheravb-rcar-gen3";
reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
reg = <0 0xe6800000 0 0x800>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
@ -524,7 +512,7 @@ avb: ethernet@e6800000 {
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 812>;
phy-mode = "rgmii-txid";
phy-mode = "rgmii";
iommus = <&ipmmu_ds0 16>;
#address-cells = <1>;
#size-cells = <0>;
@ -548,6 +536,73 @@ scif2: serial@e6e88000 {
status = "disabled";
};
i2c0: i2c@e6500000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "renesas,i2c-r8a77995",
"renesas,rcar-gen3-i2c";
reg = <0 0xe6500000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 931>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 931>;
dmas = <&dmac1 0x91>, <&dmac1 0x90>,
<&dmac2 0x91>, <&dmac2 0x90>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
i2c1: i2c@e6508000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "renesas,i2c-r8a77995",
"renesas,rcar-gen3-i2c";
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 930>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 930>;
dmas = <&dmac1 0x93>, <&dmac1 0x92>,
<&dmac2 0x93>, <&dmac2 0x92>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
i2c2: i2c@e6510000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "renesas,i2c-r8a77995",
"renesas,rcar-gen3-i2c";
reg = <0 0xe6510000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 929>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 929>;
dmas = <&dmac1 0x95>, <&dmac1 0x94>,
<&dmac2 0x95>, <&dmac2 0x94>;
dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
i2c3: i2c@e66d0000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "renesas,i2c-r8a77995",
"renesas,rcar-gen3-i2c";
reg = <0 0xe66d0000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 928>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 928>;
dmas = <&dmac0 0x97>, <&dmac0 0x96>;
dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
pwm0: pwm@e6e30000 {
compatible = "renesas,pwm-r8a77995", "renesas,pwm-rcar";
reg = <0 0xe6e30000 0 0x8>;
@ -636,5 +691,105 @@ usb2_phy0: usb-phy@ee080200 {
#phy-cells = <0>;
status = "disabled";
};
vspbs: vsp@fe960000 {
compatible = "renesas,vsp2";
reg = <0 0xfe960000 0 0x8000>;
interrupts = <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 627>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 627>;
renesas,fcp = <&fcpvb0>;
};
fcpvb0: fcp@fe96f000 {
compatible = "renesas,fcpv";
reg = <0 0xfe96f000 0 0x200>;
clocks = <&cpg CPG_MOD 607>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 607>;
iommus = <&ipmmu_vp0 5>;
};
vspd0: vsp@fea20000 {
compatible = "renesas,vsp2";
reg = <0 0xfea20000 0 0x8000>;
interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 623>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 623>;
renesas,fcp = <&fcpvd0>;
};
fcpvd0: fcp@fea27000 {
compatible = "renesas,fcpv";
reg = <0 0xfea27000 0 0x200>;
clocks = <&cpg CPG_MOD 603>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 603>;
iommus = <&ipmmu_vi0 8>;
};
vspd1: vsp@fea28000 {
compatible = "renesas,vsp2";
reg = <0 0xfea28000 0 0x8000>;
interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 622>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 622>;
renesas,fcp = <&fcpvd1>;
};
fcpvd1: fcp@fea2f000 {
compatible = "renesas,fcpv";
reg = <0 0xfea2f000 0 0x200>;
clocks = <&cpg CPG_MOD 602>;
power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
resets = <&cpg 602>;
iommus = <&ipmmu_vi0 9>;
};
du: display@feb00000 {
compatible = "renesas,du-r8a77995";
reg = <0 0xfeb00000 0 0x80000>;
interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 724>,
<&cpg CPG_MOD 723>;
clock-names = "du.0", "du.1";
vsps = <&vspd0 0 &vspd1 0>;
status = "disabled";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
du_out_rgb: endpoint {
};
};
port@1 {
reg = <1>;
du_out_lvds0: endpoint {
};
};
port@2 {
reg = <2>;
du_out_lvds1: endpoint {
};
};
};
};
};
timer {
compatible = "arm,armv8-timer";
interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
};
};

8
arch/arm64/boot/dts/renesas/salvator-common.dtsi
View file

@ -256,6 +256,7 @@ &avb {
pinctrl-0 = <&avb_pins>;
pinctrl-names = "default";
phy-handle = <&phy0>;
phy-mode = "rgmii-txid";
status = "okay";
phy0: ethernet-phy@0 {
@ -338,6 +339,13 @@ cs2000: clk_multiplier@4f {
&i2c4 {
status = "okay";
pca9654: gpio@20 {
compatible = "onnn,pca9654";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
};
csa_vdd: adc@7c {
compatible = "maxim,max9611";
reg = <0x7c>;

1
arch/arm64/boot/dts/renesas/ulcb.dtsi
View file

@ -146,6 +146,7 @@ &avb {
pinctrl-0 = <&avb_pins>;
pinctrl-names = "default";
phy-handle = <&phy0>;
phy-mode = "rgmii-txid";
status = "okay";
phy0: ethernet-phy@0 {