diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
index fc15ac519437..50b25c3da186 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
@@ -10,7 +10,7 @@ Required properties :
 Recommended properties :
 
  - clock-frequency : maximal I2C bus clock frequency in Hz.
- - efm32,location : Decides the location of the USART I/O pins.
+ - energymicro,location : Decides the location of the USART I/O pins.
    Allowed range : [0 .. 6]
 
 Example:
@@ -23,7 +23,7 @@ Example:
 		clocks = <&cmu clk_HFPERCLKI2C0>;
 		clock-frequency = <100000>;
 		status = "ok";
-		efm32,location = <3>;
+		energymicro,location = <3>;
 
 		eeprom@50 {
 			compatible = "microchip,24c02";
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index adf5e33e8312..e9c803ea306d 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -25,6 +25,7 @@ Supported adapters:
   * Intel Avoton (SOC)
   * Intel Wellsburg (PCH)
   * Intel Coleto Creek (PCH)
+  * Intel Wildcat Point (PCH)
   * Intel Wildcat Point-LP (PCH)
   * Intel BayTrail (SOC)
    Datasheets: Publicly available at the Intel website
diff --git a/Documentation/i2c/i2c-stub b/Documentation/i2c/i2c-stub
index fa4b669c166b..a16924fbd289 100644
--- a/Documentation/i2c/i2c-stub
+++ b/Documentation/i2c/i2c-stub
@@ -2,9 +2,9 @@ MODULE: i2c-stub
 
 DESCRIPTION:
 
-This module is a very simple fake I2C/SMBus driver.  It implements five
+This module is a very simple fake I2C/SMBus driver.  It implements six
 types of SMBus commands: write quick, (r/w) byte, (r/w) byte data, (r/w)
-word data, and (r/w) I2C block data.
+word data, (r/w) I2C block data, and (r/w) SMBus block data.
 
 You need to provide chip addresses as a module parameter when loading this
 driver, which will then only react to SMBus commands to these addresses.
@@ -19,6 +19,14 @@ A pointer register with auto-increment is implemented for all byte
 operations.  This allows for continuous byte reads like those supported by
 EEPROMs, among others.
 
+SMBus block command support is disabled by default, and must be enabled
+explicitly by setting the respective bits (0x03000000) in the functionality
+module parameter.
+
+SMBus block commands must be written to configure an SMBus command for
+SMBus block operations. Writes can be partial. Block read commands always
+return the number of bytes selected with the largest write so far.
+
 The typical use-case is like this:
 	1. load this module
 	2. use i2cset (from the i2c-tools project) to pre-load some data
@@ -39,15 +47,18 @@ unsigned long functionality:
 	value 0x1f0000 would only enable the quick, byte and byte data
 	commands.
 
+u8 bank_reg[10]
+u8 bank_mask[10]
+u8 bank_start[10]
+u8 bank_end[10]:
+	Optional bank settings. They tell which bits in which register
+	select the active bank, as well as the range of banked registers.
+
 CAVEATS:
 
 If your target driver polls some byte or word waiting for it to change, the
 stub could lock it up.  Use i2cset to unlock it.
 
-If the hardware for your driver has banked registers (e.g. Winbond sensors
-chips) this module will not work well - although it could be extended to
-support that pretty easily.
-
 If you spam it hard enough, printk can be lossy.  This module really wants
 something like relayfs.
 
diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig
index 7b7ea320a258..3e3b680dc007 100644
--- a/drivers/i2c/Kconfig
+++ b/drivers/i2c/Kconfig
@@ -2,7 +2,9 @@
 # I2C subsystem configuration
 #
 
-menuconfig I2C
+menu "I2C support"
+
+config I2C
 	tristate "I2C support"
 	select RT_MUTEXES
 	---help---
@@ -21,6 +23,18 @@ menuconfig I2C
 	  This I2C support can also be built as a module.  If so, the module
 	  will be called i2c-core.
 
+config I2C_ACPI
+	bool "I2C ACPI support"
+	select I2C
+	depends on ACPI
+	default y
+	help
+	  Say Y here if you want to enable ACPI I2C support. This includes support
+	  for automatic enumeration of I2C slave devices and support for ACPI I2C
+	  Operation Regions. Operation Regions allow firmware (BIOS) code to
+	  access I2C slave devices, such as smart batteries through an I2C host
+	  controller driver.
+
 if I2C
 
 config I2C_BOARDINFO
@@ -124,3 +138,5 @@ config I2C_DEBUG_BUS
 	  on.
 
 endif # I2C
+
+endmenu
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 1722f50f2473..a1f590cbb435 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -2,8 +2,11 @@
 # Makefile for the i2c core.
 #
 
+i2ccore-y := i2c-core.o
+i2ccore-$(CONFIG_I2C_ACPI)	+= i2c-acpi.o
+
 obj-$(CONFIG_I2C_BOARDINFO)	+= i2c-boardinfo.o
-obj-$(CONFIG_I2C)		+= i2c-core.o
+obj-$(CONFIG_I2C)		+= i2ccore.o
 obj-$(CONFIG_I2C_SMBUS)		+= i2c-smbus.o
 obj-$(CONFIG_I2C_CHARDEV)	+= i2c-dev.o
 obj-$(CONFIG_I2C_MUX)		+= i2c-mux.o
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 9f7d5859cf65..2ac87fa3058d 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -109,6 +109,7 @@ config I2C_I801
 	    Avoton (SOC)
 	    Wellsburg (PCH)
 	    Coleto Creek (PCH)
+	    Wildcat Point (PCH)
 	    Wildcat Point-LP (PCH)
 	    BayTrail (SOC)
 
@@ -465,9 +466,9 @@ config I2C_EG20T
 config I2C_EXYNOS5
 	tristate "Exynos5 high-speed I2C driver"
 	depends on ARCH_EXYNOS5 && OF
+	default y
 	help
-	  Say Y here to include support for high-speed I2C controller in the
-	  Exynos5 based Samsung SoCs.
+	  High-speed I2C controller on Exynos5 based Samsung SoCs.
 
 config I2C_GPIO
 	tristate "GPIO-based bitbanging I2C"
@@ -700,16 +701,6 @@ config I2C_S3C2410
 	  Say Y here to include support for I2C controller in the
 	  Samsung SoCs.
 
-config I2C_S6000
-	tristate "S6000 I2C support"
-	depends on XTENSA_VARIANT_S6000
-	help
-	  This driver supports the on chip I2C device on the
-	  S6000 xtensa processor family.
-
-	  To compile this driver as a module, choose M here. The module
-	  will be called i2c-s6000.
-
 config I2C_SH7760
 	tristate "Renesas SH7760 I2C Controller"
 	depends on CPU_SUBTYPE_SH7760
@@ -1018,37 +1009,6 @@ config I2C_CROS_EC_TUNNEL
 	  connected there. This will work whatever the interface used to
 	  talk to the EC (SPI, I2C or LPC).
 
-config SCx200_I2C
-	tristate "NatSemi SCx200 I2C using GPIO pins (DEPRECATED)"
-	depends on SCx200_GPIO
-	select I2C_ALGOBIT
-	help
-	  Enable the use of two GPIO pins of a SCx200 processor as an I2C bus.
-
-	  If you don't know what to do here, say N.
-
-	  This support is also available as a module.  If so, the module
-	  will be called scx200_i2c.
-
-	  This driver is deprecated and will be dropped soon. Use i2c-gpio
-	  (or scx200_acb) instead.
-
-config SCx200_I2C_SCL
-	int "GPIO pin used for SCL"
-	depends on SCx200_I2C
-	default "12"
-	help
-	  Enter the GPIO pin number used for the SCL signal.  This value can
-	  also be specified with a module parameter.
-
-config SCx200_I2C_SDA
-	int "GPIO pin used for SDA"
-	depends on SCx200_I2C
-	default "13"
-	help
-	  Enter the GPIO pin number used for the SSA signal.  This value can
-	  also be specified with a module parameter.
-
 config SCx200_ACB
 	tristate "Geode ACCESS.bus support"
 	depends on X86_32 && PCI
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index dd9a7f8e873f..49bf07e5ef4d 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -68,7 +68,6 @@ obj-$(CONFIG_I2C_QUP)		+= i2c-qup.o
 obj-$(CONFIG_I2C_RIIC)		+= i2c-riic.o
 obj-$(CONFIG_I2C_RK3X)		+= i2c-rk3x.o
 obj-$(CONFIG_I2C_S3C2410)	+= i2c-s3c2410.o
-obj-$(CONFIG_I2C_S6000)		+= i2c-s6000.o
 obj-$(CONFIG_I2C_SH7760)	+= i2c-sh7760.o
 obj-$(CONFIG_I2C_SH_MOBILE)	+= i2c-sh_mobile.o
 obj-$(CONFIG_I2C_SIMTEC)	+= i2c-simtec.o
@@ -101,6 +100,5 @@ obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
 obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
 obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
-obj-$(CONFIG_SCx200_I2C)	+= scx200_i2c.o
 
 ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index e95f9ba96790..79a68999a696 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -210,7 +210,7 @@ static void at91_twi_write_data_dma_callback(void *data)
 	struct at91_twi_dev *dev = (struct at91_twi_dev *)data;
 
 	dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg),
-			 dev->buf_len, DMA_MEM_TO_DEV);
+			 dev->buf_len, DMA_TO_DEVICE);
 
 	at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP);
 }
@@ -289,7 +289,7 @@ static void at91_twi_read_data_dma_callback(void *data)
 	struct at91_twi_dev *dev = (struct at91_twi_dev *)data;
 
 	dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg),
-			 dev->buf_len, DMA_DEV_TO_MEM);
+			 dev->buf_len, DMA_FROM_DEVICE);
 
 	/* The last two bytes have to be read without using dma */
 	dev->buf += dev->buf_len - 2;
@@ -768,7 +768,7 @@ static int at91_twi_probe(struct platform_device *pdev)
 	snprintf(dev->adapter.name, sizeof(dev->adapter.name), "AT91");
 	i2c_set_adapdata(&dev->adapter, dev);
 	dev->adapter.owner = THIS_MODULE;
-	dev->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
+	dev->adapter.class = I2C_CLASS_DEPRECATED;
 	dev->adapter.algo = &at91_twi_algorithm;
 	dev->adapter.dev.parent = dev->dev;
 	dev->adapter.nr = pdev->id;
diff --git a/drivers/i2c/busses/i2c-bcm2835.c b/drivers/i2c/busses/i2c-bcm2835.c
index 214ff9700efe..4b8ecd0b3661 100644
--- a/drivers/i2c/busses/i2c-bcm2835.c
+++ b/drivers/i2c/busses/i2c-bcm2835.c
@@ -277,7 +277,7 @@ static int bcm2835_i2c_probe(struct platform_device *pdev)
 	adap = &i2c_dev->adapter;
 	i2c_set_adapdata(adap, i2c_dev);
 	adap->owner = THIS_MODULE;
-	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
+	adap->class = I2C_CLASS_DEPRECATED;
 	strlcpy(adap->name, "bcm2835 I2C adapter", sizeof(adap->name));
 	adap->algo = &bcm2835_i2c_algo;
 	adap->dev.parent = &pdev->dev;
diff --git a/drivers/i2c/busses/i2c-bfin-twi.c b/drivers/i2c/busses/i2c-bfin-twi.c
index 3e271e7558d3..067c1615e968 100644
--- a/drivers/i2c/busses/i2c-bfin-twi.c
+++ b/drivers/i2c/busses/i2c-bfin-twi.c
@@ -648,7 +648,7 @@ static int i2c_bfin_twi_probe(struct platform_device *pdev)
 	strlcpy(p_adap->name, pdev->name, sizeof(p_adap->name));
 	p_adap->algo = &bfin_twi_algorithm;
 	p_adap->algo_data = iface;
-	p_adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED;
+	p_adap->class = I2C_CLASS_DEPRECATED;
 	p_adap->dev.parent = &pdev->dev;
 	p_adap->timeout = 5 * HZ;
 	p_adap->retries = 3;
diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index 389bc68c55ad..4d9614719128 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -712,7 +712,7 @@ static int davinci_i2c_probe(struct platform_device *pdev)
 	adap = &dev->adapter;
 	i2c_set_adapdata(adap, dev);
 	adap->owner = THIS_MODULE;
-	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
+	adap->class = I2C_CLASS_DEPRECATED;
 	strlcpy(adap->name, "DaVinci I2C adapter", sizeof(adap->name));
 	adap->algo = &i2c_davinci_algo;
 	adap->dev.parent = &pdev->dev;
diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c
index 3356f7ab9f79..d31d313ab4f7 100644
--- a/drivers/i2c/busses/i2c-designware-pcidrv.c
+++ b/drivers/i2c/busses/i2c-designware-pcidrv.c
@@ -188,6 +188,7 @@ static struct  dw_pci_controller  dw_pci_controllers[] = {
 		.scl_sda_cfg = &hsw_config,
 	},
 };
+
 static struct i2c_algorithm i2c_dw_algo = {
 	.master_xfer	= i2c_dw_xfer,
 	.functionality	= i2c_dw_func,
@@ -350,6 +351,14 @@ static const struct pci_device_id i2_designware_pci_ids[] = {
 	/* Haswell */
 	{ PCI_VDEVICE(INTEL, 0x9c61), haswell },
 	{ PCI_VDEVICE(INTEL, 0x9c62), haswell },
+	/* Braswell / Cherrytrail */
+	{ PCI_VDEVICE(INTEL, 0x22C1), baytrail,},
+	{ PCI_VDEVICE(INTEL, 0x22C2), baytrail },
+	{ PCI_VDEVICE(INTEL, 0x22C3), baytrail },
+	{ PCI_VDEVICE(INTEL, 0x22C4), baytrail },
+	{ PCI_VDEVICE(INTEL, 0x22C5), baytrail },
+	{ PCI_VDEVICE(INTEL, 0x22C6), baytrail },
+	{ PCI_VDEVICE(INTEL, 0x22C7), baytrail },
 	{ 0,}
 };
 MODULE_DEVICE_TABLE(pci, i2_designware_pci_ids);
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 402ec3970fed..bc8773333155 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -106,6 +106,7 @@ static const struct acpi_device_id dw_i2c_acpi_match[] = {
 	{ "INT3432", 0 },
 	{ "INT3433", 0 },
 	{ "80860F41", 0 },
+	{ "808622C1", 0 },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, dw_i2c_acpi_match);
@@ -202,7 +203,7 @@ static int dw_i2c_probe(struct platform_device *pdev)
 	adap = &dev->adapter;
 	i2c_set_adapdata(adap, dev);
 	adap->owner = THIS_MODULE;
-	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
+	adap->class = I2C_CLASS_DEPRECATED;
 	strlcpy(adap->name, "Synopsys DesignWare I2C adapter",
 			sizeof(adap->name));
 	adap->algo = &i2c_dw_algo;
diff --git a/drivers/i2c/busses/i2c-efm32.c b/drivers/i2c/busses/i2c-efm32.c
index f7eccd682de9..10b8323b08d4 100644
--- a/drivers/i2c/busses/i2c-efm32.c
+++ b/drivers/i2c/busses/i2c-efm32.c
@@ -370,7 +370,13 @@ static int efm32_i2c_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	ret = of_property_read_u32(np, "efm32,location", &location);
+
+	ret = of_property_read_u32(np, "energymicro,location", &location);
+
+	if (ret)
+		/* fall back to wrongly namespaced property */
+		ret = of_property_read_u32(np, "efm32,location", &location);
+
 	if (!ret) {
 		dev_dbg(&pdev->dev, "using location %u\n", location);
 	} else {
diff --git a/drivers/i2c/busses/i2c-exynos5.c b/drivers/i2c/busses/i2c-exynos5.c
index 63d229202854..28073f1d6d47 100644
--- a/drivers/i2c/busses/i2c-exynos5.c
+++ b/drivers/i2c/busses/i2c-exynos5.c
@@ -405,7 +405,6 @@ static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
 
 	int_status = readl(i2c->regs + HSI2C_INT_STATUS);
 	writel(int_status, i2c->regs + HSI2C_INT_STATUS);
-	fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS);
 
 	/* handle interrupt related to the transfer status */
 	if (int_status & HSI2C_INT_I2C) {
@@ -526,7 +525,7 @@ static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop)
 	if (i2c->msg->flags & I2C_M_RD) {
 		i2c_ctl |= HSI2C_RXCHON;
 
-		i2c_auto_conf = HSI2C_READ_WRITE;
+		i2c_auto_conf |= HSI2C_READ_WRITE;
 
 		trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ?
 			(i2c->variant->fifo_depth * 3 / 4) : i2c->msg->len;
@@ -549,7 +548,6 @@ static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop)
 	writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL);
 	writel(i2c_ctl, i2c->regs + HSI2C_CTL);
 
-
 	/*
 	 * Enable interrupts before starting the transfer so that we don't
 	 * miss any INT_I2C interrupts.
@@ -789,8 +787,16 @@ static int exynos5_i2c_resume_noirq(struct device *dev)
 }
 #endif
 
-static SIMPLE_DEV_PM_OPS(exynos5_i2c_dev_pm_ops, exynos5_i2c_suspend_noirq,
-			 exynos5_i2c_resume_noirq);
+static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = {
+#ifdef CONFIG_PM_SLEEP
+	.suspend_noirq = exynos5_i2c_suspend_noirq,
+	.resume_noirq = exynos5_i2c_resume_noirq,
+	.freeze_noirq = exynos5_i2c_suspend_noirq,
+	.thaw_noirq = exynos5_i2c_resume_noirq,
+	.poweroff_noirq = exynos5_i2c_suspend_noirq,
+	.restore_noirq = exynos5_i2c_resume_noirq,
+#endif
+};
 
 static struct platform_driver exynos5_i2c_driver = {
 	.probe		= exynos5_i2c_probe,
diff --git a/drivers/i2c/busses/i2c-gpio.c b/drivers/i2c/busses/i2c-gpio.c
index 71a45b210a24..933f1e453e41 100644
--- a/drivers/i2c/busses/i2c-gpio.c
+++ b/drivers/i2c/busses/i2c-gpio.c
@@ -238,12 +238,10 @@ static int i2c_gpio_probe(struct platform_device *pdev)
 static int i2c_gpio_remove(struct platform_device *pdev)
 {
 	struct i2c_gpio_private_data *priv;
-	struct i2c_gpio_platform_data *pdata;
 	struct i2c_adapter *adap;
 
 	priv = platform_get_drvdata(pdev);
 	adap = &priv->adap;
-	pdata = &priv->pdata;
 
 	i2c_del_adapter(adap);
 
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index 6777cd6f8776..2994690b26e9 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -22,57 +22,58 @@
 */
 
 /*
-  Supports the following Intel I/O Controller Hubs (ICH):
-
-                                  I/O                     Block   I2C
-                                  region  SMBus   Block   proc.   block
-  Chip name             PCI ID    size    PEC     buffer  call    read
-  ----------------------------------------------------------------------
-  82801AA  (ICH)        0x2413     16      no      no      no      no
-  82801AB  (ICH0)       0x2423     16      no      no      no      no
-  82801BA  (ICH2)       0x2443     16      no      no      no      no
-  82801CA  (ICH3)       0x2483     32     soft     no      no      no
-  82801DB  (ICH4)       0x24c3     32     hard     yes     no      no
-  82801E   (ICH5)       0x24d3     32     hard     yes     yes     yes
-  6300ESB               0x25a4     32     hard     yes     yes     yes
-  82801F   (ICH6)       0x266a     32     hard     yes     yes     yes
-  6310ESB/6320ESB       0x269b     32     hard     yes     yes     yes
-  82801G   (ICH7)       0x27da     32     hard     yes     yes     yes
-  82801H   (ICH8)       0x283e     32     hard     yes     yes     yes
-  82801I   (ICH9)       0x2930     32     hard     yes     yes     yes
-  EP80579 (Tolapai)     0x5032     32     hard     yes     yes     yes
-  ICH10                 0x3a30     32     hard     yes     yes     yes
-  ICH10                 0x3a60     32     hard     yes     yes     yes
-  5/3400 Series (PCH)   0x3b30     32     hard     yes     yes     yes
-  6 Series (PCH)        0x1c22     32     hard     yes     yes     yes
-  Patsburg (PCH)        0x1d22     32     hard     yes     yes     yes
-  Patsburg (PCH) IDF    0x1d70     32     hard     yes     yes     yes
-  Patsburg (PCH) IDF    0x1d71     32     hard     yes     yes     yes
-  Patsburg (PCH) IDF    0x1d72     32     hard     yes     yes     yes
-  DH89xxCC (PCH)        0x2330     32     hard     yes     yes     yes
-  Panther Point (PCH)   0x1e22     32     hard     yes     yes     yes
-  Lynx Point (PCH)      0x8c22     32     hard     yes     yes     yes
-  Lynx Point-LP (PCH)   0x9c22     32     hard     yes     yes     yes
-  Avoton (SOC)          0x1f3c     32     hard     yes     yes     yes
-  Wellsburg (PCH)       0x8d22     32     hard     yes     yes     yes
-  Wellsburg (PCH) MS    0x8d7d     32     hard     yes     yes     yes
-  Wellsburg (PCH) MS    0x8d7e     32     hard     yes     yes     yes
-  Wellsburg (PCH) MS    0x8d7f     32     hard     yes     yes     yes
-  Coleto Creek (PCH)    0x23b0     32     hard     yes     yes     yes
-  Wildcat Point-LP (PCH)   0x9ca2     32     hard     yes     yes     yes
-  BayTrail (SOC)        0x0f12     32     hard     yes     yes     yes
-
-  Features supported by this driver:
-  Software PEC                     no
-  Hardware PEC                     yes
-  Block buffer                     yes
-  Block process call transaction   no
-  I2C block read transaction       yes  (doesn't use the block buffer)
-  Slave mode                       no
-  Interrupt processing             yes
-
-  See the file Documentation/i2c/busses/i2c-i801 for details.
-*/
+ * Supports the following Intel I/O Controller Hubs (ICH):
+ *
+ *					I/O			Block	I2C
+ *					region	SMBus	Block	proc.	block
+ * Chip name			PCI ID	size	PEC	buffer	call	read
+ * ---------------------------------------------------------------------------
+ * 82801AA (ICH)		0x2413	16	no	no	no	no
+ * 82801AB (ICH0)		0x2423	16	no	no	no	no
+ * 82801BA (ICH2)		0x2443	16	no	no	no	no
+ * 82801CA (ICH3)		0x2483	32	soft	no	no	no
+ * 82801DB (ICH4)		0x24c3	32	hard	yes	no	no
+ * 82801E (ICH5)		0x24d3	32	hard	yes	yes	yes
+ * 6300ESB			0x25a4	32	hard	yes	yes	yes
+ * 82801F (ICH6)		0x266a	32	hard	yes	yes	yes
+ * 6310ESB/6320ESB		0x269b	32	hard	yes	yes	yes
+ * 82801G (ICH7)		0x27da	32	hard	yes	yes	yes
+ * 82801H (ICH8)		0x283e	32	hard	yes	yes	yes
+ * 82801I (ICH9)		0x2930	32	hard	yes	yes	yes
+ * EP80579 (Tolapai)		0x5032	32	hard	yes	yes	yes
+ * ICH10			0x3a30	32	hard	yes	yes	yes
+ * ICH10			0x3a60	32	hard	yes	yes	yes
+ * 5/3400 Series (PCH)		0x3b30	32	hard	yes	yes	yes
+ * 6 Series (PCH)		0x1c22	32	hard	yes	yes	yes
+ * Patsburg (PCH)		0x1d22	32	hard	yes	yes	yes
+ * Patsburg (PCH) IDF		0x1d70	32	hard	yes	yes	yes
+ * Patsburg (PCH) IDF		0x1d71	32	hard	yes	yes	yes
+ * Patsburg (PCH) IDF		0x1d72	32	hard	yes	yes	yes
+ * DH89xxCC (PCH)		0x2330	32	hard	yes	yes	yes
+ * Panther Point (PCH)		0x1e22	32	hard	yes	yes	yes
+ * Lynx Point (PCH)		0x8c22	32	hard	yes	yes	yes
+ * Lynx Point-LP (PCH)		0x9c22	32	hard	yes	yes	yes
+ * Avoton (SOC)			0x1f3c	32	hard	yes	yes	yes
+ * Wellsburg (PCH)		0x8d22	32	hard	yes	yes	yes
+ * Wellsburg (PCH) MS		0x8d7d	32	hard	yes	yes	yes
+ * Wellsburg (PCH) MS		0x8d7e	32	hard	yes	yes	yes
+ * Wellsburg (PCH) MS		0x8d7f	32	hard	yes	yes	yes
+ * Coleto Creek (PCH)		0x23b0	32	hard	yes	yes	yes
+ * Wildcat Point (PCH)		0x8ca2	32	hard	yes	yes	yes
+ * Wildcat Point-LP (PCH)	0x9ca2	32	hard	yes	yes	yes
+ * BayTrail (SOC)		0x0f12	32	hard	yes	yes	yes
+ *
+ * Features supported by this driver:
+ * Software PEC				no
+ * Hardware PEC				yes
+ * Block buffer				yes
+ * Block process call transaction	no
+ * I2C block read transaction		yes (doesn't use the block buffer)
+ * Slave mode				no
+ * Interrupt processing			yes
+ *
+ * See the file Documentation/i2c/busses/i2c-i801 for details.
+ */
 
 #include <linux/interrupt.h>
 #include <linux/module.h>
@@ -162,24 +163,25 @@
 				 STATUS_ERROR_FLAGS)
 
 /* Older devices have their ID defined in <linux/pci_ids.h> */
-#define PCI_DEVICE_ID_INTEL_BAYTRAIL_SMBUS	0x0f12
-#define PCI_DEVICE_ID_INTEL_COUGARPOINT_SMBUS	0x1c22
-#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS	0x1d22
+#define PCI_DEVICE_ID_INTEL_BAYTRAIL_SMBUS		0x0f12
+#define PCI_DEVICE_ID_INTEL_COUGARPOINT_SMBUS		0x1c22
+#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS		0x1d22
 /* Patsburg also has three 'Integrated Device Function' SMBus controllers */
-#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS_IDF0	0x1d70
-#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS_IDF1	0x1d71
-#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS_IDF2	0x1d72
-#define PCI_DEVICE_ID_INTEL_PANTHERPOINT_SMBUS	0x1e22
-#define PCI_DEVICE_ID_INTEL_AVOTON_SMBUS	0x1f3c
-#define PCI_DEVICE_ID_INTEL_DH89XXCC_SMBUS	0x2330
-#define PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS	0x23b0
-#define PCI_DEVICE_ID_INTEL_5_3400_SERIES_SMBUS	0x3b30
-#define PCI_DEVICE_ID_INTEL_LYNXPOINT_SMBUS	0x8c22
-#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS	0x8d22
-#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS0	0x8d7d
-#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS1	0x8d7e
-#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS2	0x8d7f
-#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_SMBUS	0x9c22
+#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS_IDF0		0x1d70
+#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS_IDF1		0x1d71
+#define PCI_DEVICE_ID_INTEL_PATSBURG_SMBUS_IDF2		0x1d72
+#define PCI_DEVICE_ID_INTEL_PANTHERPOINT_SMBUS		0x1e22
+#define PCI_DEVICE_ID_INTEL_AVOTON_SMBUS		0x1f3c
+#define PCI_DEVICE_ID_INTEL_DH89XXCC_SMBUS		0x2330
+#define PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS		0x23b0
+#define PCI_DEVICE_ID_INTEL_5_3400_SERIES_SMBUS		0x3b30
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_SMBUS		0x8c22
+#define PCI_DEVICE_ID_INTEL_WILDCATPOINT_SMBUS		0x8ca2
+#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS		0x8d22
+#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS0		0x8d7d
+#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS1		0x8d7e
+#define PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS2		0x8d7f
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_SMBUS		0x9c22
 #define PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_SMBUS	0x9ca2
 
 struct i801_mux_config {
@@ -823,6 +825,7 @@ static const struct pci_device_id i801_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS1) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS2) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WILDCATPOINT_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BAYTRAIL_SMBUS) },
 	{ 0, }
diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index aa8bc146718b..613069bc561a 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -735,10 +735,7 @@ static int i2c_imx_probe(struct platform_device *pdev)
 	clk_disable_unprepare(i2c_imx->clk);
 
 	dev_dbg(&i2c_imx->adapter.dev, "claimed irq %d\n", irq);
-	dev_dbg(&i2c_imx->adapter.dev, "device resources from 0x%x to 0x%x\n",
-		res->start, res->end);
-	dev_dbg(&i2c_imx->adapter.dev, "allocated %d bytes at 0x%x\n",
-		resource_size(res), res->start);
+	dev_dbg(&i2c_imx->adapter.dev, "device resources: %pR\n", res);
 	dev_dbg(&i2c_imx->adapter.dev, "adapter name: \"%s\"\n",
 		i2c_imx->adapter.name);
 	dev_info(&i2c_imx->adapter.dev, "IMX I2C adapter registered\n");
diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c
index 6a32aa095f83..0edf630b099a 100644
--- a/drivers/i2c/busses/i2c-mpc.c
+++ b/drivers/i2c/busses/i2c-mpc.c
@@ -341,8 +341,7 @@ static u32 mpc_i2c_get_sec_cfg_8xxx(void)
 			iounmap(reg);
 		}
 	}
-	if (node)
-		of_node_put(node);
+	of_node_put(node);
 
 	return val;
 }
diff --git a/drivers/i2c/busses/i2c-mv64xxx.c b/drivers/i2c/busses/i2c-mv64xxx.c
index 9f4b775e2e39..6dc5ded86f62 100644
--- a/drivers/i2c/busses/i2c-mv64xxx.c
+++ b/drivers/i2c/busses/i2c-mv64xxx.c
@@ -863,7 +863,7 @@ mv64xxx_i2c_probe(struct platform_device *pd)
 	drv_data->adapter.dev.parent = &pd->dev;
 	drv_data->adapter.algo = &mv64xxx_i2c_algo;
 	drv_data->adapter.owner = THIS_MODULE;
-	drv_data->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED;
+	drv_data->adapter.class = I2C_CLASS_DEPRECATED;
 	drv_data->adapter.nr = pd->id;
 	drv_data->adapter.dev.of_node = pd->dev.of_node;
 	platform_set_drvdata(pd, drv_data);
diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c
index 0e55d85fd4ed..9ad038d223c4 100644
--- a/drivers/i2c/busses/i2c-nomadik.c
+++ b/drivers/i2c/busses/i2c-nomadik.c
@@ -1032,10 +1032,10 @@ static int nmk_i2c_probe(struct amba_device *adev, const struct amba_id *id)
 	adap = &dev->adap;
 	adap->dev.of_node = np;
 	adap->dev.parent = &adev->dev;
-	adap->owner	= THIS_MODULE;
-	adap->class	= I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED;
-	adap->algo	= &nmk_i2c_algo;
-	adap->timeout	= msecs_to_jiffies(dev->timeout);
+	adap->owner = THIS_MODULE;
+	adap->class = I2C_CLASS_DEPRECATED;
+	adap->algo = &nmk_i2c_algo;
+	adap->timeout = msecs_to_jiffies(dev->timeout);
 	snprintf(adap->name, sizeof(adap->name),
 		 "Nomadik I2C at %pR", &adev->res);
 
diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c
index 0e10cc6182f0..2a4fe0b7cfb7 100644
--- a/drivers/i2c/busses/i2c-ocores.c
+++ b/drivers/i2c/busses/i2c-ocores.c
@@ -239,15 +239,15 @@ static u32 ocores_func(struct i2c_adapter *adap)
 }
 
 static const struct i2c_algorithm ocores_algorithm = {
-	.master_xfer	= ocores_xfer,
-	.functionality	= ocores_func,
+	.master_xfer = ocores_xfer,
+	.functionality = ocores_func,
 };
 
 static struct i2c_adapter ocores_adapter = {
-	.owner		= THIS_MODULE,
-	.name		= "i2c-ocores",
-	.class		= I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED,
-	.algo		= &ocores_algorithm,
+	.owner = THIS_MODULE,
+	.name = "i2c-ocores",
+	.class = I2C_CLASS_DEPRECATED,
+	.algo = &ocores_algorithm,
 };
 
 static const struct of_device_id ocores_i2c_match[] = {
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index b182793a4051..0dffb0e62c3b 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -1236,7 +1236,7 @@ omap_i2c_probe(struct platform_device *pdev)
 	adap = &dev->adapter;
 	i2c_set_adapdata(adap, dev);
 	adap->owner = THIS_MODULE;
-	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
+	adap->class = I2C_CLASS_DEPRECATED;
 	strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name));
 	adap->algo = &omap_i2c_algo;
 	adap->dev.parent = &pdev->dev;
diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c
index 2a5efb5b487c..3a4d64e1dfb1 100644
--- a/drivers/i2c/busses/i2c-qup.c
+++ b/drivers/i2c/busses/i2c-qup.c
@@ -633,13 +633,17 @@ static int qup_i2c_probe(struct platform_device *pdev)
 	 * associated with each byte written/received
 	 */
 	size = QUP_OUTPUT_BLOCK_SIZE(io_mode);
-	if (size >= ARRAY_SIZE(blk_sizes))
-		return -EIO;
+	if (size >= ARRAY_SIZE(blk_sizes)) {
+		ret = -EIO;
+		goto fail;
+	}
 	qup->out_blk_sz = blk_sizes[size] / 2;
 
 	size = QUP_INPUT_BLOCK_SIZE(io_mode);
-	if (size >= ARRAY_SIZE(blk_sizes))
-		return -EIO;
+	if (size >= ARRAY_SIZE(blk_sizes)) {
+		ret = -EIO;
+		goto fail;
+	}
 	qup->in_blk_sz = blk_sizes[size] / 2;
 
 	size = QUP_OUTPUT_FIFO_SIZE(io_mode);
diff --git a/drivers/i2c/busses/i2c-rcar.c b/drivers/i2c/busses/i2c-rcar.c
index 899405923678..f3c7139dfa25 100644
--- a/drivers/i2c/busses/i2c-rcar.c
+++ b/drivers/i2c/busses/i2c-rcar.c
@@ -541,13 +541,13 @@ static int rcar_i2c_probe(struct platform_device *pdev)
 	irq = platform_get_irq(pdev, 0);
 	init_waitqueue_head(&priv->wait);
 
-	adap			= &priv->adap;
-	adap->nr		= pdev->id;
-	adap->algo		= &rcar_i2c_algo;
-	adap->class		= I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED;
-	adap->retries		= 3;
-	adap->dev.parent	= dev;
-	adap->dev.of_node	= dev->of_node;
+	adap = &priv->adap;
+	adap->nr = pdev->id;
+	adap->algo = &rcar_i2c_algo;
+	adap->class = I2C_CLASS_DEPRECATED;
+	adap->retries = 3;
+	adap->dev.parent = dev;
+	adap->dev.of_node = dev->of_node;
 	i2c_set_adapdata(adap, priv);
 	strlcpy(adap->name, pdev->name, sizeof(adap->name));
 
diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c
index a9791509966a..69e11853e8bf 100644
--- a/drivers/i2c/busses/i2c-rk3x.c
+++ b/drivers/i2c/busses/i2c-rk3x.c
@@ -399,7 +399,7 @@ static irqreturn_t rk3x_i2c_irq(int irqno, void *dev_id)
 	}
 
 	/* is there anything left to handle? */
-	if (unlikely(ipd == 0))
+	if (unlikely((ipd & REG_INT_ALL) == 0))
 		goto out;
 
 	switch (i2c->state) {
diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c
index e828a1dba0e5..e086fb075f2b 100644
--- a/drivers/i2c/busses/i2c-s3c2410.c
+++ b/drivers/i2c/busses/i2c-s3c2410.c
@@ -1128,11 +1128,11 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev)
 		s3c24xx_i2c_parse_dt(pdev->dev.of_node, i2c);
 
 	strlcpy(i2c->adap.name, "s3c2410-i2c", sizeof(i2c->adap.name));
-	i2c->adap.owner   = THIS_MODULE;
-	i2c->adap.algo    = &s3c24xx_i2c_algorithm;
+	i2c->adap.owner = THIS_MODULE;
+	i2c->adap.algo = &s3c24xx_i2c_algorithm;
 	i2c->adap.retries = 2;
-	i2c->adap.class   = I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED;
-	i2c->tx_setup     = 50;
+	i2c->adap.class = I2C_CLASS_DEPRECATED;
+	i2c->tx_setup = 50;
 
 	init_waitqueue_head(&i2c->wait);
 
@@ -1267,7 +1267,7 @@ static int s3c24xx_i2c_suspend_noirq(struct device *dev)
 	return 0;
 }
 
-static int s3c24xx_i2c_resume(struct device *dev)
+static int s3c24xx_i2c_resume_noirq(struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct s3c24xx_i2c *i2c = platform_get_drvdata(pdev);
@@ -1285,7 +1285,11 @@ static int s3c24xx_i2c_resume(struct device *dev)
 static const struct dev_pm_ops s3c24xx_i2c_dev_pm_ops = {
 #ifdef CONFIG_PM_SLEEP
 	.suspend_noirq = s3c24xx_i2c_suspend_noirq,
-	.resume = s3c24xx_i2c_resume,
+	.resume_noirq = s3c24xx_i2c_resume_noirq,
+	.freeze_noirq = s3c24xx_i2c_suspend_noirq,
+	.thaw_noirq = s3c24xx_i2c_resume_noirq,
+	.poweroff_noirq = s3c24xx_i2c_suspend_noirq,
+	.restore_noirq = s3c24xx_i2c_resume_noirq,
 #endif
 };
 
diff --git a/drivers/i2c/busses/i2c-s6000.c b/drivers/i2c/busses/i2c-s6000.c
deleted file mode 100644
index dd186a037684..000000000000
--- a/drivers/i2c/busses/i2c-s6000.c
+++ /dev/null
@@ -1,404 +0,0 @@
-/*
- * drivers/i2c/busses/i2c-s6000.c
- *
- * Description: Driver for S6000 Family I2C Interface
- * Copyright (c) 2008 emlix GmbH
- * Author:	Oskar Schirmer <oskar@scara.com>
- *
- * Partially based on i2c-bfin-twi.c driver by <sonic.zhang@analog.com>
- * Copyright (c) 2005-2007 Analog Devices, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/i2c.h>
-#include <linux/i2c/s6000.h>
-#include <linux/timer.h>
-#include <linux/spinlock.h>
-#include <linux/completion.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include "i2c-s6000.h"
-
-#define DRV_NAME "i2c-s6000"
-
-#define POLL_TIMEOUT	(2 * HZ)
-
-struct s6i2c_if {
-	u8 __iomem		*reg; /* memory mapped registers */
-	int			irq;
-	spinlock_t		lock;
-	struct i2c_msg		*msgs; /* messages currently handled */
-	int			msgs_num; /* nb of msgs to do */
-	int			msgs_push; /* nb of msgs read/written */
-	int			msgs_done; /* nb of msgs finally handled */
-	unsigned		push; /* nb of bytes read/written in msg */
-	unsigned		done; /* nb of bytes finally handled */
-	int			timeout_count; /* timeout retries left */
-	struct timer_list	timeout_timer;
-	struct i2c_adapter	adap;
-	struct completion	complete;
-	struct clk		*clk;
-	struct resource		*res;
-};
-
-static inline u16 i2c_rd16(struct s6i2c_if *iface, unsigned n)
-{
-	return readw(iface->reg + (n));
-}
-
-static inline void i2c_wr16(struct s6i2c_if *iface, unsigned n, u16 v)
-{
-	writew(v, iface->reg + (n));
-}
-
-static inline u32 i2c_rd32(struct s6i2c_if *iface, unsigned n)
-{
-	return readl(iface->reg + (n));
-}
-
-static inline void i2c_wr32(struct s6i2c_if *iface, unsigned n, u32 v)
-{
-	writel(v, iface->reg + (n));
-}
-
-static struct s6i2c_if s6i2c_if;
-
-static void s6i2c_handle_interrupt(struct s6i2c_if *iface)
-{
-	if (i2c_rd16(iface, S6_I2C_INTRSTAT) & (1 << S6_I2C_INTR_TXABRT)) {
-		i2c_rd16(iface, S6_I2C_CLRTXABRT);
-		i2c_wr16(iface, S6_I2C_INTRMASK, 0);
-		complete(&iface->complete);
-		return;
-	}
-	if (iface->msgs_done >= iface->msgs_num) {
-		dev_err(&iface->adap.dev, "s6i2c: spurious I2C irq: %04x\n",
-			i2c_rd16(iface, S6_I2C_INTRSTAT));
-		i2c_wr16(iface, S6_I2C_INTRMASK, 0);
-		return;
-	}
-	while ((iface->msgs_push < iface->msgs_num)
-	    && (i2c_rd16(iface, S6_I2C_STATUS) & (1 << S6_I2C_STATUS_TFNF))) {
-		struct i2c_msg *m = &iface->msgs[iface->msgs_push];
-		if (!(m->flags & I2C_M_RD))
-			i2c_wr16(iface, S6_I2C_DATACMD, m->buf[iface->push]);
-		else
-			i2c_wr16(iface, S6_I2C_DATACMD,
-				 1 << S6_I2C_DATACMD_READ);
-		if (++iface->push >= m->len) {
-			iface->push = 0;
-			iface->msgs_push += 1;
-		}
-	}
-	do {
-		struct i2c_msg *m = &iface->msgs[iface->msgs_done];
-		if (!(m->flags & I2C_M_RD)) {
-			if (iface->msgs_done < iface->msgs_push)
-				iface->msgs_done += 1;
-			else
-				break;
-		} else if (i2c_rd16(iface, S6_I2C_STATUS)
-				& (1 << S6_I2C_STATUS_RFNE)) {
-			m->buf[iface->done] = i2c_rd16(iface, S6_I2C_DATACMD);
-			if (++iface->done >= m->len) {
-				iface->done = 0;
-				iface->msgs_done += 1;
-			}
-		} else{
-			break;
-		}
-	} while (iface->msgs_done < iface->msgs_num);
-	if (iface->msgs_done >= iface->msgs_num) {
-		i2c_wr16(iface, S6_I2C_INTRMASK, 1 << S6_I2C_INTR_TXABRT);
-		complete(&iface->complete);
-	} else if (iface->msgs_push >= iface->msgs_num) {
-		i2c_wr16(iface, S6_I2C_INTRMASK, (1 << S6_I2C_INTR_TXABRT) |
-						 (1 << S6_I2C_INTR_RXFULL));
-	} else {
-		i2c_wr16(iface, S6_I2C_INTRMASK, (1 << S6_I2C_INTR_TXABRT) |
-						 (1 << S6_I2C_INTR_TXEMPTY) |
-						 (1 << S6_I2C_INTR_RXFULL));
-	}
-}
-
-static irqreturn_t s6i2c_interrupt_entry(int irq, void *dev_id)
-{
-	struct s6i2c_if *iface = dev_id;
-	if (!(i2c_rd16(iface, S6_I2C_STATUS) & ((1 << S6_I2C_INTR_RXUNDER)
-					      | (1 << S6_I2C_INTR_RXOVER)
-					      | (1 << S6_I2C_INTR_RXFULL)
-					      | (1 << S6_I2C_INTR_TXOVER)
-					      | (1 << S6_I2C_INTR_TXEMPTY)
-					      | (1 << S6_I2C_INTR_RDREQ)
-					      | (1 << S6_I2C_INTR_TXABRT)
-					      | (1 << S6_I2C_INTR_RXDONE)
-					      | (1 << S6_I2C_INTR_ACTIVITY)
-					      | (1 << S6_I2C_INTR_STOPDET)
-					      | (1 << S6_I2C_INTR_STARTDET)
-					      | (1 << S6_I2C_INTR_GENCALL))))
-		return IRQ_NONE;
-
-	spin_lock(&iface->lock);
-	del_timer(&iface->timeout_timer);
-	s6i2c_handle_interrupt(iface);
-	spin_unlock(&iface->lock);
-	return IRQ_HANDLED;
-}
-
-static void s6i2c_timeout(unsigned long data)
-{
-	struct s6i2c_if *iface = (struct s6i2c_if *)data;
-	unsigned long flags;
-
-	spin_lock_irqsave(&iface->lock, flags);
-	s6i2c_handle_interrupt(iface);
-	if (--iface->timeout_count > 0) {
-		iface->timeout_timer.expires = jiffies + POLL_TIMEOUT;
-		add_timer(&iface->timeout_timer);
-	} else {
-		complete(&iface->complete);
-		i2c_wr16(iface, S6_I2C_INTRMASK, 0);
-	}
-	spin_unlock_irqrestore(&iface->lock, flags);
-}
-
-static int s6i2c_master_xfer(struct i2c_adapter *adap,
-				struct i2c_msg *msgs, int num)
-{
-	struct s6i2c_if *iface = adap->algo_data;
-	int i;
-	if (num == 0)
-		return 0;
-	if (i2c_rd16(iface, S6_I2C_STATUS) & (1 << S6_I2C_STATUS_ACTIVITY))
-		yield();
-	i2c_wr16(iface, S6_I2C_INTRMASK, 0);
-	i2c_rd16(iface, S6_I2C_CLRINTR);
-	for (i = 0; i < num; i++) {
-		if (msgs[i].flags & I2C_M_TEN) {
-			dev_err(&adap->dev,
-				"s6i2c: 10 bits addr not supported\n");
-			return -EINVAL;
-		}
-		if (msgs[i].len == 0) {
-			dev_err(&adap->dev,
-				"s6i2c: zero length message not supported\n");
-			return -EINVAL;
-		}
-		if (msgs[i].addr != msgs[0].addr) {
-			dev_err(&adap->dev,
-				"s6i2c: multiple xfer cannot change target\n");
-			return -EINVAL;
-		}
-	}
-
-	iface->msgs = msgs;
-	iface->msgs_num = num;
-	iface->msgs_push = 0;
-	iface->msgs_done = 0;
-	iface->push = 0;
-	iface->done = 0;
-	iface->timeout_count = 10;
-	i2c_wr16(iface, S6_I2C_TAR, msgs[0].addr);
-	i2c_wr16(iface, S6_I2C_ENABLE, 1);
-	i2c_wr16(iface, S6_I2C_INTRMASK, (1 << S6_I2C_INTR_TXEMPTY) |
-					 (1 << S6_I2C_INTR_TXABRT));
-
-	iface->timeout_timer.expires = jiffies + POLL_TIMEOUT;
-	add_timer(&iface->timeout_timer);
-	wait_for_completion(&iface->complete);
-	del_timer_sync(&iface->timeout_timer);
-	while (i2c_rd32(iface, S6_I2C_TXFLR) > 0)
-		schedule();
-	while (i2c_rd16(iface, S6_I2C_STATUS) & (1 << S6_I2C_STATUS_ACTIVITY))
-		schedule();
-
-	i2c_wr16(iface, S6_I2C_INTRMASK, 0);
-	i2c_wr16(iface, S6_I2C_ENABLE, 0);
-	return iface->msgs_done;
-}
-
-static u32 s6i2c_functionality(struct i2c_adapter *adap)
-{
-	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
-}
-
-static struct i2c_algorithm s6i2c_algorithm = {
-	.master_xfer   = s6i2c_master_xfer,
-	.functionality = s6i2c_functionality,
-};
-
-static u16 nanoseconds_on_clk(struct s6i2c_if *iface, u32 ns)
-{
-	u32 dividend = ((clk_get_rate(iface->clk) / 1000) * ns) / 1000000;
-	if (dividend > 0xffff)
-		return 0xffff;
-	return dividend;
-}
-
-static int s6i2c_probe(struct platform_device *dev)
-{
-	struct s6i2c_if *iface = &s6i2c_if;
-	struct i2c_adapter *p_adap;
-	const char *clock;
-	int bus_num, rc;
-	spin_lock_init(&iface->lock);
-	init_completion(&iface->complete);
-	iface->irq = platform_get_irq(dev, 0);
-	if (iface->irq < 0) {
-		rc = iface->irq;
-		goto err_out;
-	}
-	iface->res = platform_get_resource(dev, IORESOURCE_MEM, 0);
-	if (!iface->res) {
-		rc = -ENXIO;
-		goto err_out;
-	}
-	iface->res = request_mem_region(iface->res->start,
-					resource_size(iface->res),
-					dev->dev.bus_id);
-	if (!iface->res) {
-		rc = -EBUSY;
-		goto err_out;
-	}
-	iface->reg = ioremap_nocache(iface->res->start,
-				     resource_size(iface->res));
-	if (!iface->reg) {
-		rc = -ENOMEM;
-		goto err_reg;
-	}
-
-	clock = 0;
-	bus_num = -1;
-	if (dev_get_platdata(&dev->dev)) {
-		struct s6_i2c_platform_data *pdata =
-			dev_get_platdata(&dev->dev);
-		bus_num = pdata->bus_num;
-		clock = pdata->clock;
-	}
-	iface->clk = clk_get(&dev->dev, clock);
-	if (IS_ERR(iface->clk)) {
-		rc = PTR_ERR(iface->clk);
-		goto err_map;
-	}
-	rc = clk_enable(iface->clk);
-	if (rc < 0)
-		goto err_clk_put;
-	init_timer(&iface->timeout_timer);
-	iface->timeout_timer.function = s6i2c_timeout;
-	iface->timeout_timer.data = (unsigned long)iface;
-
-	p_adap = &iface->adap;
-	strlcpy(p_adap->name, dev->name, sizeof(p_adap->name));
-	p_adap->algo = &s6i2c_algorithm;
-	p_adap->algo_data = iface;
-	p_adap->nr = bus_num;
-	p_adap->class = 0;
-	p_adap->dev.parent = &dev->dev;
-	i2c_wr16(iface, S6_I2C_INTRMASK, 0);
-	rc = request_irq(iface->irq, s6i2c_interrupt_entry,
-			 IRQF_SHARED, dev->name, iface);
-	if (rc) {
-		dev_err(&p_adap->dev, "s6i2c: can't get IRQ %d\n", iface->irq);
-		goto err_clk_dis;
-	}
-
-	i2c_wr16(iface, S6_I2C_ENABLE, 0);
-	udelay(1);
-	i2c_wr32(iface, S6_I2C_SRESET, 1 << S6_I2C_SRESET_IC_SRST);
-	i2c_wr16(iface, S6_I2C_CLRTXABRT, 1);
-	i2c_wr16(iface, S6_I2C_CON,
-			(1 << S6_I2C_CON_MASTER) |
-			(S6_I2C_CON_SPEED_NORMAL << S6_I2C_CON_SPEED) |
-			(0 << S6_I2C_CON_10BITSLAVE) |
-			(0 << S6_I2C_CON_10BITMASTER) |
-			(1 << S6_I2C_CON_RESTARTENA) |
-			(1 << S6_I2C_CON_SLAVEDISABLE));
-	i2c_wr16(iface, S6_I2C_SSHCNT, nanoseconds_on_clk(iface, 4000));
-	i2c_wr16(iface, S6_I2C_SSLCNT, nanoseconds_on_clk(iface, 4700));
-	i2c_wr16(iface, S6_I2C_FSHCNT, nanoseconds_on_clk(iface, 600));
-	i2c_wr16(iface, S6_I2C_FSLCNT, nanoseconds_on_clk(iface, 1300));
-	i2c_wr16(iface, S6_I2C_RXTL, 0);
-	i2c_wr16(iface, S6_I2C_TXTL, 0);
-
-	platform_set_drvdata(dev, iface);
-	rc = i2c_add_numbered_adapter(p_adap);
-	if (rc)
-		goto err_irq_free;
-	return 0;
-
-err_irq_free:
-	free_irq(iface->irq, iface);
-err_clk_dis:
-	clk_disable(iface->clk);
-err_clk_put:
-	clk_put(iface->clk);
-err_map:
-	iounmap(iface->reg);
-err_reg:
-	release_mem_region(iface->res->start,
-			   resource_size(iface->res));
-err_out:
-	return rc;
-}
-
-static int s6i2c_remove(struct platform_device *pdev)
-{
-	struct s6i2c_if *iface = platform_get_drvdata(pdev);
-	i2c_wr16(iface, S6_I2C_ENABLE, 0);
-	i2c_del_adapter(&iface->adap);
-	free_irq(iface->irq, iface);
-	clk_disable(iface->clk);
-	clk_put(iface->clk);
-	iounmap(iface->reg);
-	release_mem_region(iface->res->start,
-			   resource_size(iface->res));
-	return 0;
-}
-
-static struct platform_driver s6i2c_driver = {
-	.probe		= s6i2c_probe,
-	.remove		= s6i2c_remove,
-	.driver		= {
-		.name	= DRV_NAME,
-		.owner	= THIS_MODULE,
-	},
-};
-
-static int __init s6i2c_init(void)
-{
-	pr_info("I2C: S6000 I2C driver\n");
-	return platform_driver_register(&s6i2c_driver);
-}
-
-static void __exit s6i2c_exit(void)
-{
-	platform_driver_unregister(&s6i2c_driver);
-}
-
-MODULE_DESCRIPTION("I2C-Bus adapter routines for S6000 I2C");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:" DRV_NAME);
-
-subsys_initcall(s6i2c_init);
-module_exit(s6i2c_exit);
diff --git a/drivers/i2c/busses/i2c-s6000.h b/drivers/i2c/busses/i2c-s6000.h
deleted file mode 100644
index 4936f9f2256f..000000000000
--- a/drivers/i2c/busses/i2c-s6000.h
+++ /dev/null
@@ -1,79 +0,0 @@
-/*
- * drivers/i2c/busses/i2c-s6000.h
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2008 Emlix GmbH <info@emlix.com>
- * Author:	Oskar Schirmer <oskar@scara.com>
- */
-
-#ifndef __DRIVERS_I2C_BUSSES_I2C_S6000_H
-#define __DRIVERS_I2C_BUSSES_I2C_S6000_H
-
-#define S6_I2C_CON		0x000
-#define S6_I2C_CON_MASTER		0
-#define S6_I2C_CON_SPEED		1
-#define S6_I2C_CON_SPEED_NORMAL			1
-#define S6_I2C_CON_SPEED_FAST			2
-#define S6_I2C_CON_SPEED_MASK			3
-#define S6_I2C_CON_10BITSLAVE		3
-#define S6_I2C_CON_10BITMASTER		4
-#define S6_I2C_CON_RESTARTENA		5
-#define S6_I2C_CON_SLAVEDISABLE		6
-#define S6_I2C_TAR		0x004
-#define S6_I2C_TAR_GCORSTART		10
-#define S6_I2C_TAR_SPECIAL		11
-#define S6_I2C_SAR		0x008
-#define S6_I2C_HSMADDR		0x00C
-#define S6_I2C_DATACMD		0x010
-#define S6_I2C_DATACMD_READ		8
-#define S6_I2C_SSHCNT		0x014
-#define S6_I2C_SSLCNT		0x018
-#define S6_I2C_FSHCNT		0x01C
-#define S6_I2C_FSLCNT		0x020
-#define S6_I2C_INTRSTAT		0x02C
-#define S6_I2C_INTRMASK		0x030
-#define S6_I2C_RAWINTR		0x034
-#define S6_I2C_INTR_RXUNDER		0
-#define S6_I2C_INTR_RXOVER		1
-#define S6_I2C_INTR_RXFULL		2
-#define S6_I2C_INTR_TXOVER		3
-#define S6_I2C_INTR_TXEMPTY		4
-#define S6_I2C_INTR_RDREQ		5
-#define S6_I2C_INTR_TXABRT		6
-#define S6_I2C_INTR_RXDONE		7
-#define S6_I2C_INTR_ACTIVITY		8
-#define S6_I2C_INTR_STOPDET		9
-#define S6_I2C_INTR_STARTDET		10
-#define S6_I2C_INTR_GENCALL		11
-#define S6_I2C_RXTL		0x038
-#define S6_I2C_TXTL		0x03C
-#define S6_I2C_CLRINTR		0x040
-#define S6_I2C_CLRRXUNDER	0x044
-#define S6_I2C_CLRRXOVER	0x048
-#define S6_I2C_CLRTXOVER	0x04C
-#define S6_I2C_CLRRDREQ		0x050
-#define S6_I2C_CLRTXABRT	0x054
-#define S6_I2C_CLRRXDONE	0x058
-#define S6_I2C_CLRACTIVITY	0x05C
-#define S6_I2C_CLRSTOPDET	0x060
-#define S6_I2C_CLRSTARTDET	0x064
-#define S6_I2C_CLRGENCALL	0x068
-#define S6_I2C_ENABLE		0x06C
-#define S6_I2C_STATUS		0x070
-#define S6_I2C_STATUS_ACTIVITY		0
-#define S6_I2C_STATUS_TFNF		1
-#define S6_I2C_STATUS_TFE		2
-#define S6_I2C_STATUS_RFNE		3
-#define S6_I2C_STATUS_RFF		4
-#define S6_I2C_TXFLR		0x074
-#define S6_I2C_RXFLR		0x078
-#define S6_I2C_SRESET		0x07C
-#define S6_I2C_SRESET_IC_SRST		0
-#define S6_I2C_SRESET_IC_MASTER_SRST	1
-#define S6_I2C_SRESET_IC_SLAVE_SRST	2
-#define S6_I2C_TXABRTSOURCE	0x080
-
-#endif
diff --git a/drivers/i2c/busses/i2c-sirf.c b/drivers/i2c/busses/i2c-sirf.c
index a3216defc1d3..b1336d5f0531 100644
--- a/drivers/i2c/busses/i2c-sirf.c
+++ b/drivers/i2c/busses/i2c-sirf.c
@@ -311,7 +311,7 @@ static int i2c_sirfsoc_probe(struct platform_device *pdev)
 		goto out;
 	}
 	adap = &siic->adapter;
-	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
+	adap->class = I2C_CLASS_DEPRECATED;
 
 	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	siic->base = devm_ioremap_resource(&pdev->dev, mem_res);
diff --git a/drivers/i2c/busses/i2c-st.c b/drivers/i2c/busses/i2c-st.c
index 95b947670386..2e4eccd6599a 100644
--- a/drivers/i2c/busses/i2c-st.c
+++ b/drivers/i2c/busses/i2c-st.c
@@ -206,25 +206,31 @@ static inline void st_i2c_clr_bits(void __iomem *reg, u32 mask)
 	writel_relaxed(readl_relaxed(reg) & ~mask, reg);
 }
 
-/* From I2C Specifications v0.5 */
+/*
+ * From I2C Specifications v0.5.
+ *
+ * All the values below have +10% margin added to be
+ * compatible with some out-of-spec devices,
+ * like HDMI link of the Toshiba 19AV600 TV.
+ */
 static struct st_i2c_timings i2c_timings[] = {
 	[I2C_MODE_STANDARD] = {
 		.rate			= 100000,
-		.rep_start_hold		= 4000,
-		.rep_start_setup	= 4700,
-		.start_hold		= 4000,
-		.data_setup_time	= 250,
-		.stop_setup_time	= 4000,
-		.bus_free_time		= 4700,
+		.rep_start_hold		= 4400,
+		.rep_start_setup	= 5170,
+		.start_hold		= 4400,
+		.data_setup_time	= 275,
+		.stop_setup_time	= 4400,
+		.bus_free_time		= 5170,
 	},
 	[I2C_MODE_FAST] = {
 		.rate			= 400000,
-		.rep_start_hold		= 600,
-		.rep_start_setup	= 600,
-		.start_hold		= 600,
-		.data_setup_time	= 100,
-		.stop_setup_time	= 600,
-		.bus_free_time		= 1300,
+		.rep_start_hold		= 660,
+		.rep_start_setup	= 660,
+		.start_hold		= 660,
+		.data_setup_time	= 110,
+		.stop_setup_time	= 660,
+		.bus_free_time		= 1430,
 	},
 };
 
@@ -815,7 +821,7 @@ static int st_i2c_probe(struct platform_device *pdev)
 
 	adap = &i2c_dev->adap;
 	i2c_set_adapdata(adap, i2c_dev);
-	snprintf(adap->name, sizeof(adap->name), "ST I2C(0x%x)", res->start);
+	snprintf(adap->name, sizeof(adap->name), "ST I2C(0x%pa)", &res->start);
 	adap->owner = THIS_MODULE;
 	adap->timeout = 2 * HZ;
 	adap->retries = 0;
diff --git a/drivers/i2c/busses/i2c-stu300.c b/drivers/i2c/busses/i2c-stu300.c
index fefb1c19ec1d..6a44f37798c8 100644
--- a/drivers/i2c/busses/i2c-stu300.c
+++ b/drivers/i2c/busses/i2c-stu300.c
@@ -909,7 +909,7 @@ static int stu300_probe(struct platform_device *pdev)
 	adap = &dev->adapter;
 	adap->owner = THIS_MODULE;
 	/* DDC class but actually often used for more generic I2C */
-	adap->class = I2C_CLASS_DDC | I2C_CLASS_DEPRECATED;
+	adap->class = I2C_CLASS_DEPRECATED;
 	strlcpy(adap->name, "ST Microelectronics DDC I2C adapter",
 		sizeof(adap->name));
 	adap->nr = bus_nr;
diff --git a/drivers/i2c/busses/i2c-taos-evm.c b/drivers/i2c/busses/i2c-taos-evm.c
index 057602683553..10855a0b7e7f 100644
--- a/drivers/i2c/busses/i2c-taos-evm.c
+++ b/drivers/i2c/busses/i2c-taos-evm.c
@@ -311,19 +311,8 @@ static struct serio_driver taos_drv = {
 	.interrupt	= taos_interrupt,
 };
 
-static int __init taos_init(void)
-{
-	return serio_register_driver(&taos_drv);
-}
-
-static void __exit taos_exit(void)
-{
-	serio_unregister_driver(&taos_drv);
-}
+module_serio_driver(taos_drv);
 
 MODULE_AUTHOR("Jean Delvare <jdelvare@suse.de>");
 MODULE_DESCRIPTION("TAOS evaluation module driver");
 MODULE_LICENSE("GPL");
-
-module_init(taos_init);
-module_exit(taos_exit);
diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
index f1bb2fc06791..87d0371cebb7 100644
--- a/drivers/i2c/busses/i2c-tegra.c
+++ b/drivers/i2c/busses/i2c-tegra.c
@@ -792,7 +792,7 @@ static int tegra_i2c_probe(struct platform_device *pdev)
 
 	i2c_set_adapdata(&i2c_dev->adapter, i2c_dev);
 	i2c_dev->adapter.owner = THIS_MODULE;
-	i2c_dev->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
+	i2c_dev->adapter.class = I2C_CLASS_DEPRECATED;
 	strlcpy(i2c_dev->adapter.name, "Tegra I2C adapter",
 		sizeof(i2c_dev->adapter.name));
 	i2c_dev->adapter.algo = &tegra_i2c_algo;
diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
index 7731f1795869..ade9223912d3 100644
--- a/drivers/i2c/busses/i2c-xiic.c
+++ b/drivers/i2c/busses/i2c-xiic.c
@@ -677,15 +677,15 @@ static u32 xiic_func(struct i2c_adapter *adap)
 }
 
 static const struct i2c_algorithm xiic_algorithm = {
-	.master_xfer	= xiic_xfer,
-	.functionality	= xiic_func,
+	.master_xfer = xiic_xfer,
+	.functionality = xiic_func,
 };
 
 static struct i2c_adapter xiic_adapter = {
-	.owner		= THIS_MODULE,
-	.name		= DRIVER_NAME,
-	.class		= I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED,
-	.algo		= &xiic_algorithm,
+	.owner = THIS_MODULE,
+	.name = DRIVER_NAME,
+	.class = I2C_CLASS_DEPRECATED,
+	.algo = &xiic_algorithm,
 };
 
 
diff --git a/drivers/i2c/busses/scx200_i2c.c b/drivers/i2c/busses/scx200_i2c.c
deleted file mode 100644
index 8eadf0f47ad7..000000000000
--- a/drivers/i2c/busses/scx200_i2c.c
+++ /dev/null
@@ -1,129 +0,0 @@
-/* linux/drivers/i2c/busses/scx200_i2c.c
-
-   Copyright (c) 2001,2002 Christer Weinigel <wingel@nano-system.com>
-
-   National Semiconductor SCx200 I2C bus on GPIO pins
-
-   Based on i2c-velleman.c Copyright (C) 1995-96, 2000 Simon G. Vogl
-
-   This program is free software; you can redistribute it and/or modify
-   it under the terms of the GNU General Public License as published by
-   the Free Software Foundation; either version 2 of the License, or
-   (at your option) any later version.
-   
-   This program is distributed in the hope that it will be useful,
-   but WITHOUT ANY WARRANTY; without even the implied warranty of
-   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-   GNU General Public License for more details.
-   
-   You should have received a copy of the GNU General Public License
-   along with this program; if not, write to the Free Software
-   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.		     
-*/
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/i2c.h>
-#include <linux/i2c-algo-bit.h>
-#include <linux/io.h>
-
-#include <linux/scx200_gpio.h>
-
-MODULE_AUTHOR("Christer Weinigel <wingel@nano-system.com>");
-MODULE_DESCRIPTION("NatSemi SCx200 I2C Driver");
-MODULE_LICENSE("GPL");
-
-static int scl = CONFIG_SCx200_I2C_SCL;
-static int sda = CONFIG_SCx200_I2C_SDA;
-
-module_param(scl, int, 0);
-MODULE_PARM_DESC(scl, "GPIO line for SCL");
-module_param(sda, int, 0);
-MODULE_PARM_DESC(sda, "GPIO line for SDA");
-
-static void scx200_i2c_setscl(void *data, int state)
-{
-	scx200_gpio_set(scl, state);
-}
-
-static void scx200_i2c_setsda(void *data, int state)
-{
-	scx200_gpio_set(sda, state);
-} 
-
-static int scx200_i2c_getscl(void *data)
-{
-	return scx200_gpio_get(scl);
-}
-
-static int scx200_i2c_getsda(void *data)
-{
-	return scx200_gpio_get(sda);
-}
-
-/* ------------------------------------------------------------------------
- * Encapsulate the above functions in the correct operations structure.
- * This is only done when more than one hardware adapter is supported.
- */
-
-static struct i2c_algo_bit_data scx200_i2c_data = {
-	.setsda		= scx200_i2c_setsda,
-	.setscl		= scx200_i2c_setscl,
-	.getsda		= scx200_i2c_getsda,
-	.getscl		= scx200_i2c_getscl,
-	.udelay		= 10,
-	.timeout	= HZ,
-};
-
-static struct i2c_adapter scx200_i2c_ops = {
-	.owner		   = THIS_MODULE,
-	.class             = I2C_CLASS_HWMON | I2C_CLASS_SPD,
-	.algo_data	   = &scx200_i2c_data,
-	.name	= "NatSemi SCx200 I2C",
-};
-
-static int scx200_i2c_init(void)
-{
-	pr_debug("NatSemi SCx200 I2C Driver\n");
-
-	if (!scx200_gpio_present()) {
-		pr_err("no SCx200 gpio pins available\n");
-		return -ENODEV;
-	}
-
-	pr_debug("SCL=GPIO%02u, SDA=GPIO%02u\n", scl, sda);
-
-	if (scl == -1 || sda == -1 || scl == sda) {
-		pr_err("scl and sda must be specified\n");
-		return -EINVAL;
-	}
-
-	/* Configure GPIOs as open collector outputs */
-	scx200_gpio_configure(scl, ~2, 5);
-	scx200_gpio_configure(sda, ~2, 5);
-
-	if (i2c_bit_add_bus(&scx200_i2c_ops) < 0) {
-		pr_err("adapter %s registration failed\n", scx200_i2c_ops.name);
-		return -ENODEV;
-	}
-	
-	return 0;
-}
-
-static void scx200_i2c_cleanup(void)
-{
-	i2c_del_adapter(&scx200_i2c_ops);
-}
-
-module_init(scx200_i2c_init);
-module_exit(scx200_i2c_cleanup);
-
-/*
-    Local variables:
-        compile-command: "make -k -C ../.. SUBDIRS=drivers/i2c modules"
-        c-basic-offset: 8
-    End:
-*/
diff --git a/drivers/i2c/i2c-acpi.c b/drivers/i2c/i2c-acpi.c
new file mode 100644
index 000000000000..e8b61967334b
--- /dev/null
+++ b/drivers/i2c/i2c-acpi.c
@@ -0,0 +1,362 @@
+/*
+ * I2C ACPI code
+ *
+ * Copyright (C) 2014 Intel Corp
+ *
+ * Author: Lan Tianyu <tianyu.lan@intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ * for more details.
+ */
+#define pr_fmt(fmt) "I2C/ACPI : " fmt
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/acpi.h>
+
+struct acpi_i2c_handler_data {
+	struct acpi_connection_info info;
+	struct i2c_adapter *adapter;
+};
+
+struct gsb_buffer {
+	u8	status;
+	u8	len;
+	union {
+		u16	wdata;
+		u8	bdata;
+		u8	data[0];
+	};
+} __packed;
+
+static int acpi_i2c_add_resource(struct acpi_resource *ares, void *data)
+{
+	struct i2c_board_info *info = data;
+
+	if (ares->type == ACPI_RESOURCE_TYPE_SERIAL_BUS) {
+		struct acpi_resource_i2c_serialbus *sb;
+
+		sb = &ares->data.i2c_serial_bus;
+		if (sb->type == ACPI_RESOURCE_SERIAL_TYPE_I2C) {
+			info->addr = sb->slave_address;
+			if (sb->access_mode == ACPI_I2C_10BIT_MODE)
+				info->flags |= I2C_CLIENT_TEN;
+		}
+	} else if (info->irq < 0) {
+		struct resource r;
+
+		if (acpi_dev_resource_interrupt(ares, 0, &r))
+			info->irq = r.start;
+	}
+
+	/* Tell the ACPI core to skip this resource */
+	return 1;
+}
+
+static acpi_status acpi_i2c_add_device(acpi_handle handle, u32 level,
+				       void *data, void **return_value)
+{
+	struct i2c_adapter *adapter = data;
+	struct list_head resource_list;
+	struct i2c_board_info info;
+	struct acpi_device *adev;
+	int ret;
+
+	if (acpi_bus_get_device(handle, &adev))
+		return AE_OK;
+	if (acpi_bus_get_status(adev) || !adev->status.present)
+		return AE_OK;
+
+	memset(&info, 0, sizeof(info));
+	info.acpi_node.companion = adev;
+	info.irq = -1;
+
+	INIT_LIST_HEAD(&resource_list);
+	ret = acpi_dev_get_resources(adev, &resource_list,
+				     acpi_i2c_add_resource, &info);
+	acpi_dev_free_resource_list(&resource_list);
+
+	if (ret < 0 || !info.addr)
+		return AE_OK;
+
+	adev->power.flags.ignore_parent = true;
+	strlcpy(info.type, dev_name(&adev->dev), sizeof(info.type));
+	if (!i2c_new_device(adapter, &info)) {
+		adev->power.flags.ignore_parent = false;
+		dev_err(&adapter->dev,
+			"failed to add I2C device %s from ACPI\n",
+			dev_name(&adev->dev));
+	}
+
+	return AE_OK;
+}
+
+/**
+ * acpi_i2c_register_devices - enumerate I2C slave devices behind adapter
+ * @adap: pointer to adapter
+ *
+ * Enumerate all I2C slave devices behind this adapter by walking the ACPI
+ * namespace. When a device is found it will be added to the Linux device
+ * model and bound to the corresponding ACPI handle.
+ */
+void acpi_i2c_register_devices(struct i2c_adapter *adap)
+{
+	acpi_handle handle;
+	acpi_status status;
+
+	if (!adap->dev.parent)
+		return;
+
+	handle = ACPI_HANDLE(adap->dev.parent);
+	if (!handle)
+		return;
+
+	status = acpi_walk_namespace(ACPI_TYPE_DEVICE, handle, 1,
+				     acpi_i2c_add_device, NULL,
+				     adap, NULL);
+	if (ACPI_FAILURE(status))
+		dev_warn(&adap->dev, "failed to enumerate I2C slaves\n");
+}
+
+static int acpi_gsb_i2c_read_bytes(struct i2c_client *client,
+		u8 cmd, u8 *data, u8 data_len)
+{
+
+	struct i2c_msg msgs[2];
+	int ret;
+	u8 *buffer;
+
+	buffer = kzalloc(data_len, GFP_KERNEL);
+	if (!buffer)
+		return AE_NO_MEMORY;
+
+	msgs[0].addr = client->addr;
+	msgs[0].flags = client->flags;
+	msgs[0].len = 1;
+	msgs[0].buf = &cmd;
+
+	msgs[1].addr = client->addr;
+	msgs[1].flags = client->flags | I2C_M_RD;
+	msgs[1].len = data_len;
+	msgs[1].buf = buffer;
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret < 0)
+		dev_err(&client->adapter->dev, "i2c read failed\n");
+	else
+		memcpy(data, buffer, data_len);
+
+	kfree(buffer);
+	return ret;
+}
+
+static int acpi_gsb_i2c_write_bytes(struct i2c_client *client,
+		u8 cmd, u8 *data, u8 data_len)
+{
+
+	struct i2c_msg msgs[1];
+	u8 *buffer;
+	int ret = AE_OK;
+
+	buffer = kzalloc(data_len + 1, GFP_KERNEL);
+	if (!buffer)
+		return AE_NO_MEMORY;
+
+	buffer[0] = cmd;
+	memcpy(buffer + 1, data, data_len);
+
+	msgs[0].addr = client->addr;
+	msgs[0].flags = client->flags;
+	msgs[0].len = data_len + 1;
+	msgs[0].buf = buffer;
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret < 0)
+		dev_err(&client->adapter->dev, "i2c write failed\n");
+
+	kfree(buffer);
+	return ret;
+}
+
+static acpi_status
+acpi_i2c_space_handler(u32 function, acpi_physical_address command,
+			u32 bits, u64 *value64,
+			void *handler_context, void *region_context)
+{
+	struct gsb_buffer *gsb = (struct gsb_buffer *)value64;
+	struct acpi_i2c_handler_data *data = handler_context;
+	struct acpi_connection_info *info = &data->info;
+	struct acpi_resource_i2c_serialbus *sb;
+	struct i2c_adapter *adapter = data->adapter;
+	struct i2c_client client;
+	struct acpi_resource *ares;
+	u32 accessor_type = function >> 16;
+	u8 action = function & ACPI_IO_MASK;
+	acpi_status ret = AE_OK;
+	int status;
+
+	ret = acpi_buffer_to_resource(info->connection, info->length, &ares);
+	if (ACPI_FAILURE(ret))
+		return ret;
+
+	if (!value64 || ares->type != ACPI_RESOURCE_TYPE_SERIAL_BUS) {
+		ret = AE_BAD_PARAMETER;
+		goto err;
+	}
+
+	sb = &ares->data.i2c_serial_bus;
+	if (sb->type != ACPI_RESOURCE_SERIAL_TYPE_I2C) {
+		ret = AE_BAD_PARAMETER;
+		goto err;
+	}
+
+	memset(&client, 0, sizeof(client));
+	client.adapter = adapter;
+	client.addr = sb->slave_address;
+	client.flags = 0;
+
+	if (sb->access_mode == ACPI_I2C_10BIT_MODE)
+		client.flags |= I2C_CLIENT_TEN;
+
+	switch (accessor_type) {
+	case ACPI_GSB_ACCESS_ATTRIB_SEND_RCV:
+		if (action == ACPI_READ) {
+			status = i2c_smbus_read_byte(&client);
+			if (status >= 0) {
+				gsb->bdata = status;
+				status = 0;
+			}
+		} else {
+			status = i2c_smbus_write_byte(&client, gsb->bdata);
+		}
+		break;
+
+	case ACPI_GSB_ACCESS_ATTRIB_BYTE:
+		if (action == ACPI_READ) {
+			status = i2c_smbus_read_byte_data(&client, command);
+			if (status >= 0) {
+				gsb->bdata = status;
+				status = 0;
+			}
+		} else {
+			status = i2c_smbus_write_byte_data(&client, command,
+					gsb->bdata);
+		}
+		break;
+
+	case ACPI_GSB_ACCESS_ATTRIB_WORD:
+		if (action == ACPI_READ) {
+			status = i2c_smbus_read_word_data(&client, command);
+			if (status >= 0) {
+				gsb->wdata = status;
+				status = 0;
+			}
+		} else {
+			status = i2c_smbus_write_word_data(&client, command,
+					gsb->wdata);
+		}
+		break;
+
+	case ACPI_GSB_ACCESS_ATTRIB_BLOCK:
+		if (action == ACPI_READ) {
+			status = i2c_smbus_read_block_data(&client, command,
+					gsb->data);
+			if (status >= 0) {
+				gsb->len = status;
+				status = 0;
+			}
+		} else {
+			status = i2c_smbus_write_block_data(&client, command,
+					gsb->len, gsb->data);
+		}
+		break;
+
+	case ACPI_GSB_ACCESS_ATTRIB_MULTIBYTE:
+		if (action == ACPI_READ) {
+			status = acpi_gsb_i2c_read_bytes(&client, command,
+					gsb->data, info->access_length);
+			if (status > 0)
+				status = 0;
+		} else {
+			status = acpi_gsb_i2c_write_bytes(&client, command,
+					gsb->data, info->access_length);
+		}
+		break;
+
+	default:
+		pr_info("protocol(0x%02x) is not supported.\n", accessor_type);
+		ret = AE_BAD_PARAMETER;
+		goto err;
+	}
+
+	gsb->status = status;
+
+ err:
+	ACPI_FREE(ares);
+	return ret;
+}
+
+
+int acpi_i2c_install_space_handler(struct i2c_adapter *adapter)
+{
+	acpi_handle handle = ACPI_HANDLE(adapter->dev.parent);
+	struct acpi_i2c_handler_data *data;
+	acpi_status status;
+
+	if (!handle)
+		return -ENODEV;
+
+	data = kzalloc(sizeof(struct acpi_i2c_handler_data),
+			    GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->adapter = adapter;
+	status = acpi_bus_attach_private_data(handle, (void *)data);
+	if (ACPI_FAILURE(status)) {
+		kfree(data);
+		return -ENOMEM;
+	}
+
+	status = acpi_install_address_space_handler(handle,
+				ACPI_ADR_SPACE_GSBUS,
+				&acpi_i2c_space_handler,
+				NULL,
+				data);
+	if (ACPI_FAILURE(status)) {
+		dev_err(&adapter->dev, "Error installing i2c space handler\n");
+		acpi_bus_detach_private_data(handle);
+		kfree(data);
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+void acpi_i2c_remove_space_handler(struct i2c_adapter *adapter)
+{
+	acpi_handle handle = ACPI_HANDLE(adapter->dev.parent);
+	struct acpi_i2c_handler_data *data;
+	acpi_status status;
+
+	if (!handle)
+		return;
+
+	acpi_remove_address_space_handler(handle,
+				ACPI_ADR_SPACE_GSBUS,
+				&acpi_i2c_space_handler);
+
+	status = acpi_bus_get_private_data(handle, (void **)&data);
+	if (ACPI_SUCCESS(status))
+		kfree(data);
+
+	acpi_bus_detach_private_data(handle);
+}
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index 66aa83b99383..632057a44615 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -1097,101 +1097,6 @@ EXPORT_SYMBOL(of_find_i2c_adapter_by_node);
 static void of_i2c_register_devices(struct i2c_adapter *adap) { }
 #endif /* CONFIG_OF */
 
-/* ACPI support code */
-
-#if IS_ENABLED(CONFIG_ACPI)
-static int acpi_i2c_add_resource(struct acpi_resource *ares, void *data)
-{
-	struct i2c_board_info *info = data;
-
-	if (ares->type == ACPI_RESOURCE_TYPE_SERIAL_BUS) {
-		struct acpi_resource_i2c_serialbus *sb;
-
-		sb = &ares->data.i2c_serial_bus;
-		if (sb->type == ACPI_RESOURCE_SERIAL_TYPE_I2C) {
-			info->addr = sb->slave_address;
-			if (sb->access_mode == ACPI_I2C_10BIT_MODE)
-				info->flags |= I2C_CLIENT_TEN;
-		}
-	} else if (info->irq < 0) {
-		struct resource r;
-
-		if (acpi_dev_resource_interrupt(ares, 0, &r))
-			info->irq = r.start;
-	}
-
-	/* Tell the ACPI core to skip this resource */
-	return 1;
-}
-
-static acpi_status acpi_i2c_add_device(acpi_handle handle, u32 level,
-				       void *data, void **return_value)
-{
-	struct i2c_adapter *adapter = data;
-	struct list_head resource_list;
-	struct i2c_board_info info;
-	struct acpi_device *adev;
-	int ret;
-
-	if (acpi_bus_get_device(handle, &adev))
-		return AE_OK;
-	if (acpi_bus_get_status(adev) || !adev->status.present)
-		return AE_OK;
-
-	memset(&info, 0, sizeof(info));
-	info.acpi_node.companion = adev;
-	info.irq = -1;
-
-	INIT_LIST_HEAD(&resource_list);
-	ret = acpi_dev_get_resources(adev, &resource_list,
-				     acpi_i2c_add_resource, &info);
-	acpi_dev_free_resource_list(&resource_list);
-
-	if (ret < 0 || !info.addr)
-		return AE_OK;
-
-	adev->power.flags.ignore_parent = true;
-	strlcpy(info.type, dev_name(&adev->dev), sizeof(info.type));
-	if (!i2c_new_device(adapter, &info)) {
-		adev->power.flags.ignore_parent = false;
-		dev_err(&adapter->dev,
-			"failed to add I2C device %s from ACPI\n",
-			dev_name(&adev->dev));
-	}
-
-	return AE_OK;
-}
-
-/**
- * acpi_i2c_register_devices - enumerate I2C slave devices behind adapter
- * @adap: pointer to adapter
- *
- * Enumerate all I2C slave devices behind this adapter by walking the ACPI
- * namespace. When a device is found it will be added to the Linux device
- * model and bound to the corresponding ACPI handle.
- */
-static void acpi_i2c_register_devices(struct i2c_adapter *adap)
-{
-	acpi_handle handle;
-	acpi_status status;
-
-	if (!adap->dev.parent)
-		return;
-
-	handle = ACPI_HANDLE(adap->dev.parent);
-	if (!handle)
-		return;
-
-	status = acpi_walk_namespace(ACPI_TYPE_DEVICE, handle, 1,
-				     acpi_i2c_add_device, NULL,
-				     adap, NULL);
-	if (ACPI_FAILURE(status))
-		dev_warn(&adap->dev, "failed to enumerate I2C slaves\n");
-}
-#else
-static inline void acpi_i2c_register_devices(struct i2c_adapter *adap) {}
-#endif /* CONFIG_ACPI */
-
 static int i2c_do_add_adapter(struct i2c_driver *driver,
 			      struct i2c_adapter *adap)
 {
@@ -1298,6 +1203,7 @@ exit_recovery:
 	/* create pre-declared device nodes */
 	of_i2c_register_devices(adap);
 	acpi_i2c_register_devices(adap);
+	acpi_i2c_install_space_handler(adap);
 
 	if (adap->nr < __i2c_first_dynamic_bus_num)
 		i2c_scan_static_board_info(adap);
@@ -1471,6 +1377,7 @@ void i2c_del_adapter(struct i2c_adapter *adap)
 		return;
 	}
 
+	acpi_i2c_remove_space_handler(adap);
 	/* Tell drivers about this removal */
 	mutex_lock(&core_lock);
 	bus_for_each_drv(&i2c_bus_type, NULL, adap,
@@ -2013,6 +1920,16 @@ static int i2c_detect(struct i2c_adapter *adapter, struct i2c_driver *driver)
 	if (!driver->detect || !address_list)
 		return 0;
 
+	/* Warn that the adapter lost class based instantiation */
+	if (adapter->class == I2C_CLASS_DEPRECATED) {
+		dev_dbg(&adapter->dev,
+			"This adapter dropped support for I2C classes and "
+			"won't auto-detect %s devices anymore. If you need it, check "
+			"'Documentation/i2c/instantiating-devices' for alternatives.\n",
+			driver->driver.name);
+		return 0;
+	}
+
 	/* Stop here if the classes do not match */
 	if (!(adapter->class & driver->class))
 		return 0;
diff --git a/drivers/i2c/i2c-stub.c b/drivers/i2c/i2c-stub.c
index 77e4849d2f2a..d241aa295d96 100644
--- a/drivers/i2c/i2c-stub.c
+++ b/drivers/i2c/i2c-stub.c
@@ -2,7 +2,7 @@
     i2c-stub.c - I2C/SMBus chip emulator
 
     Copyright (c) 2004 Mark M. Hoffman <mhoffman@lightlink.com>
-    Copyright (C) 2007, 2012 Jean Delvare <jdelvare@suse.de>
+    Copyright (C) 2007-2014 Jean Delvare <jdelvare@suse.de>
 
     This program is free software; you can redistribute it and/or modify
     it under the terms of the GNU General Public License as published by
@@ -27,28 +27,109 @@
 #include <linux/slab.h>
 #include <linux/errno.h>
 #include <linux/i2c.h>
+#include <linux/list.h>
 
 #define MAX_CHIPS 10
-#define STUB_FUNC (I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | \
-		   I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | \
-		   I2C_FUNC_SMBUS_I2C_BLOCK)
+
+/*
+ * Support for I2C_FUNC_SMBUS_BLOCK_DATA is disabled by default and must
+ * be enabled explicitly by setting the I2C_FUNC_SMBUS_BLOCK_DATA bits
+ * in the 'functionality' module parameter.
+ */
+#define STUB_FUNC_DEFAULT \
+		(I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | \
+		 I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | \
+		 I2C_FUNC_SMBUS_I2C_BLOCK)
+
+#define STUB_FUNC_ALL \
+		(STUB_FUNC_DEFAULT | I2C_FUNC_SMBUS_BLOCK_DATA)
 
 static unsigned short chip_addr[MAX_CHIPS];
 module_param_array(chip_addr, ushort, NULL, S_IRUGO);
 MODULE_PARM_DESC(chip_addr,
 		 "Chip addresses (up to 10, between 0x03 and 0x77)");
 
-static unsigned long functionality = STUB_FUNC;
+static unsigned long functionality = STUB_FUNC_DEFAULT;
 module_param(functionality, ulong, S_IRUGO | S_IWUSR);
 MODULE_PARM_DESC(functionality, "Override functionality bitfield");
 
+/* Some chips have banked register ranges */
+
+static u8 bank_reg[MAX_CHIPS];
+module_param_array(bank_reg, byte, NULL, S_IRUGO);
+MODULE_PARM_DESC(bank_reg, "Bank register");
+
+static u8 bank_mask[MAX_CHIPS];
+module_param_array(bank_mask, byte, NULL, S_IRUGO);
+MODULE_PARM_DESC(bank_mask, "Bank value mask");
+
+static u8 bank_start[MAX_CHIPS];
+module_param_array(bank_start, byte, NULL, S_IRUGO);
+MODULE_PARM_DESC(bank_start, "First banked register");
+
+static u8 bank_end[MAX_CHIPS];
+module_param_array(bank_end, byte, NULL, S_IRUGO);
+MODULE_PARM_DESC(bank_end, "Last banked register");
+
+struct smbus_block_data {
+	struct list_head node;
+	u8 command;
+	u8 len;
+	u8 block[I2C_SMBUS_BLOCK_MAX];
+};
+
 struct stub_chip {
 	u8 pointer;
 	u16 words[256];		/* Byte operations use the LSB as per SMBus
 				   specification */
+	struct list_head smbus_blocks;
+
+	/* For chips with banks, extra registers are allocated dynamically */
+	u8 bank_reg;
+	u8 bank_shift;
+	u8 bank_mask;
+	u8 bank_sel;		/* Currently selected bank */
+	u8 bank_start;
+	u8 bank_end;
+	u16 bank_size;
+	u16 *bank_words;	/* Room for bank_mask * bank_size registers */
 };
 
 static struct stub_chip *stub_chips;
+static int stub_chips_nr;
+
+static struct smbus_block_data *stub_find_block(struct device *dev,
+						struct stub_chip *chip,
+						u8 command, bool create)
+{
+	struct smbus_block_data *b, *rb = NULL;
+
+	list_for_each_entry(b, &chip->smbus_blocks, node) {
+		if (b->command == command) {
+			rb = b;
+			break;
+		}
+	}
+	if (rb == NULL && create) {
+		rb = devm_kzalloc(dev, sizeof(*rb), GFP_KERNEL);
+		if (rb == NULL)
+			return rb;
+		rb->command = command;
+		list_add(&rb->node, &chip->smbus_blocks);
+	}
+	return rb;
+}
+
+static u16 *stub_get_wordp(struct stub_chip *chip, u8 offset)
+{
+	if (chip->bank_sel &&
+	    offset >= chip->bank_start && offset <= chip->bank_end)
+		return chip->bank_words +
+		       (chip->bank_sel - 1) * chip->bank_size +
+		       offset - chip->bank_start;
+	else
+		return chip->words + offset;
+}
 
 /* Return negative errno on error. */
 static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
@@ -57,9 +138,11 @@ static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
 	s32 ret;
 	int i, len;
 	struct stub_chip *chip = NULL;
+	struct smbus_block_data *b;
+	u16 *wordp;
 
 	/* Search for the right chip */
-	for (i = 0; i < MAX_CHIPS && chip_addr[i]; i++) {
+	for (i = 0; i < stub_chips_nr; i++) {
 		if (addr == chip_addr[i]) {
 			chip = stub_chips + i;
 			break;
@@ -82,7 +165,8 @@ static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
 				"smbus byte - addr 0x%02x, wrote 0x%02x.\n",
 				addr, command);
 		} else {
-			data->byte = chip->words[chip->pointer++] & 0xff;
+			wordp = stub_get_wordp(chip, chip->pointer++);
+			data->byte = *wordp & 0xff;
 			dev_dbg(&adap->dev,
 				"smbus byte - addr 0x%02x, read  0x%02x.\n",
 				addr, data->byte);
@@ -92,14 +176,25 @@ static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
 		break;
 
 	case I2C_SMBUS_BYTE_DATA:
+		wordp = stub_get_wordp(chip, command);
 		if (read_write == I2C_SMBUS_WRITE) {
-			chip->words[command] &= 0xff00;
-			chip->words[command] |= data->byte;
+			*wordp &= 0xff00;
+			*wordp |= data->byte;
 			dev_dbg(&adap->dev,
 				"smbus byte data - addr 0x%02x, wrote 0x%02x at 0x%02x.\n",
 				addr, data->byte, command);
+
+			/* Set the bank as needed */
+			if (chip->bank_words && command == chip->bank_reg) {
+				chip->bank_sel =
+					(data->byte >> chip->bank_shift)
+					& chip->bank_mask;
+				dev_dbg(&adap->dev,
+					"switching to bank %u.\n",
+					chip->bank_sel);
+			}
 		} else {
-			data->byte = chip->words[command] & 0xff;
+			data->byte = *wordp & 0xff;
 			dev_dbg(&adap->dev,
 				"smbus byte data - addr 0x%02x, read  0x%02x at 0x%02x.\n",
 				addr, data->byte, command);
@@ -110,13 +205,14 @@ static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
 		break;
 
 	case I2C_SMBUS_WORD_DATA:
+		wordp = stub_get_wordp(chip, command);
 		if (read_write == I2C_SMBUS_WRITE) {
-			chip->words[command] = data->word;
+			*wordp = data->word;
 			dev_dbg(&adap->dev,
 				"smbus word data - addr 0x%02x, wrote 0x%04x at 0x%02x.\n",
 				addr, data->word, command);
 		} else {
-			data->word = chip->words[command];
+			data->word = *wordp;
 			dev_dbg(&adap->dev,
 				"smbus word data - addr 0x%02x, read  0x%04x at 0x%02x.\n",
 				addr, data->word, command);
@@ -126,6 +222,12 @@ static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
 		break;
 
 	case I2C_SMBUS_I2C_BLOCK_DATA:
+		/*
+		 * We ignore banks here, because banked chips don't use I2C
+		 * block transfers
+		 */
+		if (data->block[0] > 256 - command)	/* Avoid overrun */
+			data->block[0] = 256 - command;
 		len = data->block[0];
 		if (read_write == I2C_SMBUS_WRITE) {
 			for (i = 0; i < len; i++) {
@@ -148,6 +250,55 @@ static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
 		ret = 0;
 		break;
 
+	case I2C_SMBUS_BLOCK_DATA:
+		/*
+		 * We ignore banks here, because chips typically don't use both
+		 * banks and SMBus block transfers
+		 */
+		b = stub_find_block(&adap->dev, chip, command, false);
+		if (read_write == I2C_SMBUS_WRITE) {
+			len = data->block[0];
+			if (len == 0 || len > I2C_SMBUS_BLOCK_MAX) {
+				ret = -EINVAL;
+				break;
+			}
+			if (b == NULL) {
+				b = stub_find_block(&adap->dev, chip, command,
+						    true);
+				if (b == NULL) {
+					ret = -ENOMEM;
+					break;
+				}
+			}
+			/* Largest write sets read block length */
+			if (len > b->len)
+				b->len = len;
+			for (i = 0; i < len; i++)
+				b->block[i] = data->block[i + 1];
+			/* update for byte and word commands */
+			chip->words[command] = (b->block[0] << 8) | b->len;
+			dev_dbg(&adap->dev,
+				"smbus block data - addr 0x%02x, wrote %d bytes at 0x%02x.\n",
+				addr, len, command);
+		} else {
+			if (b == NULL) {
+				dev_dbg(&adap->dev,
+					"SMBus block read command without prior block write not supported\n");
+				ret = -EOPNOTSUPP;
+				break;
+			}
+			len = b->len;
+			data->block[0] = len;
+			for (i = 0; i < len; i++)
+				data->block[i + 1] = b->block[i];
+			dev_dbg(&adap->dev,
+				"smbus block data - addr 0x%02x, read  %d bytes at 0x%02x.\n",
+				addr, len, command);
+		}
+
+		ret = 0;
+		break;
+
 	default:
 		dev_dbg(&adap->dev, "Unsupported I2C/SMBus command\n");
 		ret = -EOPNOTSUPP;
@@ -159,7 +310,7 @@ static s32 stub_xfer(struct i2c_adapter *adap, u16 addr, unsigned short flags,
 
 static u32 stub_func(struct i2c_adapter *adapter)
 {
-	return STUB_FUNC & functionality;
+	return STUB_FUNC_ALL & functionality;
 }
 
 static const struct i2c_algorithm smbus_algorithm = {
@@ -174,6 +325,43 @@ static struct i2c_adapter stub_adapter = {
 	.name		= "SMBus stub driver",
 };
 
+static int __init i2c_stub_allocate_banks(int i)
+{
+	struct stub_chip *chip = stub_chips + i;
+
+	chip->bank_reg = bank_reg[i];
+	chip->bank_start = bank_start[i];
+	chip->bank_end = bank_end[i];
+	chip->bank_size = bank_end[i] - bank_start[i] + 1;
+
+	/* We assume that all bits in the mask are contiguous */
+	chip->bank_mask = bank_mask[i];
+	while (!(chip->bank_mask & 1)) {
+		chip->bank_shift++;
+		chip->bank_mask >>= 1;
+	}
+
+	chip->bank_words = kzalloc(chip->bank_mask * chip->bank_size *
+				   sizeof(u16), GFP_KERNEL);
+	if (!chip->bank_words)
+		return -ENOMEM;
+
+	pr_debug("i2c-stub: Allocated %u banks of %u words each (registers 0x%02x to 0x%02x)\n",
+		 chip->bank_mask, chip->bank_size, chip->bank_start,
+		 chip->bank_end);
+
+	return 0;
+}
+
+static void i2c_stub_free(void)
+{
+	int i;
+
+	for (i = 0; i < stub_chips_nr; i++)
+		kfree(stub_chips[i].bank_words);
+	kfree(stub_chips);
+}
+
 static int __init i2c_stub_init(void)
 {
 	int i, ret;
@@ -194,22 +382,39 @@ static int __init i2c_stub_init(void)
 	}
 
 	/* Allocate memory for all chips at once */
-	stub_chips = kzalloc(i * sizeof(struct stub_chip), GFP_KERNEL);
+	stub_chips_nr = i;
+	stub_chips = kcalloc(stub_chips_nr, sizeof(struct stub_chip),
+			     GFP_KERNEL);
 	if (!stub_chips) {
 		pr_err("i2c-stub: Out of memory\n");
 		return -ENOMEM;
 	}
+	for (i = 0; i < stub_chips_nr; i++) {
+		INIT_LIST_HEAD(&stub_chips[i].smbus_blocks);
+
+		/* Allocate extra memory for banked register ranges */
+		if (bank_mask[i]) {
+			ret = i2c_stub_allocate_banks(i);
+			if (ret)
+				goto fail_free;
+		}
+	}
 
 	ret = i2c_add_adapter(&stub_adapter);
 	if (ret)
-		kfree(stub_chips);
+		goto fail_free;
+
+	return 0;
+
+ fail_free:
+	i2c_stub_free();
 	return ret;
 }
 
 static void __exit i2c_stub_exit(void)
 {
 	i2c_del_adapter(&stub_adapter);
-	kfree(stub_chips);
+	i2c_stub_free();
 }
 
 MODULE_AUTHOR("Mark M. Hoffman <mhoffman@lightlink.com>");
diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c
index 9bd4212782ab..ec11b404b433 100644
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -41,6 +41,7 @@
 #include <linux/i2c-mux.h>
 #include <linux/i2c/pca954x.h>
 #include <linux/module.h>
+#include <linux/pm.h>
 #include <linux/slab.h>
 
 #define PCA954X_MAX_NCHANS 8
@@ -273,9 +274,23 @@ static int pca954x_remove(struct i2c_client *client)
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+static int pca954x_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct pca954x *data = i2c_get_clientdata(client);
+
+	data->last_chan = 0;
+	return i2c_smbus_write_byte(client, 0);
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(pca954x_pm, NULL, pca954x_resume);
+
 static struct i2c_driver pca954x_driver = {
 	.driver		= {
 		.name	= "pca954x",
+		.pm	= &pca954x_pm,
 		.owner	= THIS_MODULE,
 	},
 	.probe		= pca954x_probe,
diff --git a/include/linux/acpi.h b/include/linux/acpi.h
index 5320153c311b..807cbc46d73e 100644
--- a/include/linux/acpi.h
+++ b/include/linux/acpi.h
@@ -364,6 +364,17 @@ extern bool osc_sb_apei_support_acked;
 #define OSC_PCI_EXPRESS_CAPABILITY_CONTROL	0x00000010
 #define OSC_PCI_CONTROL_MASKS			0x0000001f
 
+#define ACPI_GSB_ACCESS_ATTRIB_QUICK		0x00000002
+#define ACPI_GSB_ACCESS_ATTRIB_SEND_RCV         0x00000004
+#define ACPI_GSB_ACCESS_ATTRIB_BYTE		0x00000006
+#define ACPI_GSB_ACCESS_ATTRIB_WORD		0x00000008
+#define ACPI_GSB_ACCESS_ATTRIB_BLOCK		0x0000000A
+#define ACPI_GSB_ACCESS_ATTRIB_MULTIBYTE	0x0000000B
+#define ACPI_GSB_ACCESS_ATTRIB_WORD_CALL	0x0000000C
+#define ACPI_GSB_ACCESS_ATTRIB_BLOCK_CALL	0x0000000D
+#define ACPI_GSB_ACCESS_ATTRIB_RAW_BYTES	0x0000000E
+#define ACPI_GSB_ACCESS_ATTRIB_RAW_PROCESS	0x0000000F
+
 extern acpi_status acpi_pci_osc_control_set(acpi_handle handle,
 					     u32 *mask, u32 req);
 
diff --git a/include/linux/i2c.h b/include/linux/i2c.h
index b556e0ab946f..ea507665896c 100644
--- a/include/linux/i2c.h
+++ b/include/linux/i2c.h
@@ -577,4 +577,16 @@ static inline struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node
 }
 #endif /* CONFIG_OF */
 
+#ifdef CONFIG_I2C_ACPI
+int acpi_i2c_install_space_handler(struct i2c_adapter *adapter);
+void acpi_i2c_remove_space_handler(struct i2c_adapter *adapter);
+void acpi_i2c_register_devices(struct i2c_adapter *adap);
+#else
+static inline void acpi_i2c_register_devices(struct i2c_adapter *adap) { }
+static inline void acpi_i2c_remove_space_handler(struct i2c_adapter *adapter)
+{ }
+static inline int acpi_i2c_install_space_handler(struct i2c_adapter *adapter)
+{ return 0; }
+#endif
+
 #endif /* _LINUX_I2C_H */
diff --git a/include/linux/i2c/s6000.h b/include/linux/i2c/s6000.h
deleted file mode 100644
index d9b34bfdae76..000000000000
--- a/include/linux/i2c/s6000.h
+++ /dev/null
@@ -1,10 +0,0 @@
-#ifndef __LINUX_I2C_S6000_H
-#define __LINUX_I2C_S6000_H
-
-struct s6_i2c_platform_data {
-	const char *clock; /* the clock to use */
-	int bus_num; /* the bus number to register */
-};
-
-#endif
-