commit 24e0e61db3 upstream.
In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."
In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."
Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.
DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.
sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.
This change is based on a patch originally submitted by Runa Guo-oc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3d26c5702 upstream.
HFSC assumes that inner classes have an fsc curve, but it is currently
possible for classes without an fsc curve to become parents. This leads
to bugs including a use-after-free.
Don't allow non-root classes without HFSC_FSC to become parents.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Budimir Markovic <markovicbudimir@gmail.com>
Signed-off-by: Budimir Markovic <markovicbudimir@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20230824084905.422-1-markovicbudimir@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ v4.14: Delete NL_SET_ERR_MSG because extack is not added to hfsc_change_class ]
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fda67e8c3 upstream.
With the configuration PAGE_SIZE 64k and filesystem blocksize 64k,
a problem occurred when more than 13 million files were directly created
under a directory:
EXT4-fs error (device xx): ext4_dx_csum_set:492: inode #xxxx: comm xxxxx: dir seems corrupt? Run e2fsck -D.
EXT4-fs error (device xx): ext4_dx_csum_verify:463: inode #xxxx: comm xxxxx: dir seems corrupt? Run e2fsck -D.
EXT4-fs error (device xx): dx_probe:856: inode #xxxx: block 8188: comm xxxxx: Directory index failed checksum
When enough files are created, the fake_dirent->reclen will be 0xffff.
it doesn't equal to the blocksize 65536, i.e. 0x10000.
But it is not the same condition when blocksize equals to 4k.
when enough files are created, the fake_dirent->reclen will be 0x1000.
it equals to the blocksize 4k, i.e. 0x1000.
The problem seems to be related to the limitation of the 16-bit field
when the blocksize is set to 64k.
To address this, helpers like ext4_rec_len_{from,to}_disk has already
been introduced to complete the conversion between the encoded and the
plain form of rec_len.
So fix this one by using the helper, and all the other in this file too.
Cc: stable@kernel.org
Fixes: dbe8944404 ("ext4: Calculate and verify checksums for htree nodes")
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Suggested-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Shida Zhang <zhangshida@kylinos.cn>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20230803060938.1929759-1-zhangshida@kylinos.cn
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Shida Zhang <zhangshida@kylinos.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c31515857 upstream.
The elf-fdpic loader hard sets the process personality to either
PER_LINUX_FDPIC for true elf-fdpic binaries or to PER_LINUX for normal ELF
binaries (in this case they would be constant displacement compiled with
-pie for example). The problem with that is that it will lose any other
bits that may be in the ELF header personality (such as the "bug
emulation" bits).
On the ARM architecture the ADDR_LIMIT_32BIT flag is used to signify a
normal 32bit binary - as opposed to a legacy 26bit address binary. This
matters since start_thread() will set the ARM CPSR register as required
based on this flag. If the elf-fdpic loader loses this bit the process
will be mis-configured and crash out pretty quickly.
Modify elf-fdpic loader personality setting so that it preserves the upper
three bytes by using the SET_PERSONALITY macro to set it. This macro in
the generic case sets PER_LINUX and preserves the upper bytes.
Architectures can override this for their specific use case, and ARM does
exactly this.
The problem shows up quite easily running under qemu using the ARM
architecture, but not necessarily on all types of real ARM hardware. If
the underlying ARM processor does not support the legacy 26-bit addressing
mode then everything will work as expected.
Link: https://lkml.kernel.org/r/20230907011808.2985083-1-gerg@kernel.org
Fixes: 1bde925d23 ("fs/binfmt_elf_fdpic.c: provide NOMMU loader for regular ELF binaries")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Ungerer <gerg@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 753a4d531b upstream.
On certain SATA controllers, softreset fails after wakeup from S2RAM with
the message "softreset failed (1st FIS failed)", sometimes resulting in
drives not being detected again. With the increased timeout, this issue
is avoided. Instead, "softreset failed (device not ready)" is now
logged 1-2 times; this later failure seems to cause fewer problems
however, and the drives are detected reliably once they've spun up and
the probe is retried.
The issue was observed with the primary SATA controller of the QNAP
TS-453B, which is an "Intel Corporation Celeron/Pentium Silver Processor
SATA Controller [8086:31e3] (rev 06)" integrated in the Celeron J4125 CPU,
and the following drives:
- Seagate IronWolf ST12000VN0008
- Seagate IronWolf ST8000NE0004
The SATA controller seems to be more relevant to this issue than the
drives, as the same drives are always detected reliably on the secondary
SATA controller on the same board (an ASMedia 106x) without any "softreset
failed" errors even without the increased timeout.
Fixes: e7d3ef13d5 ("libata: change drive ready wait after hard reset to 5s")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84d76529c6 upstream.
Whenever an ATA adapter driver is removed (e.g. rmmod),
ata_port_detach() is called repeatedly for all the adapter ports to
remove (unload) the devices attached to the port and delete the port
device itself. Removing of devices is done using libata EH with the
ATA_PFLAG_UNLOADING port flag set. This causes libata EH to execute
ata_eh_unload() which disables all devices attached to the port.
ata_port_detach() finishes by calling scsi_remove_host() to remove the
scsi host associated with the port. This function will trigger the
removal of all scsi devices attached to the host and in the case of
disks, calls to sd_shutdown() which will flush the device write cache
and stop the device. However, given that the devices were already
disabled by ata_eh_unload(), the synchronize write cache command and
start stop unit commands fail. E.g. running "rmmod ahci" with first
removing sd_mod results in error messages like:
ata13.00: disable device
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 0:0:0:0: [sda] Stopping disk
sd 0:0:0:0: [sda] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
Fix this by removing all scsi devices of the ata devices connected to
the port before scheduling libata EH to disable the ATA devices.
Fixes: 720ba12620 ("[PATCH] libata-hp: update unload-unplug")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b8e0af4a7 upstream.
The function ata_port_request_pm() checks the port flag
ATA_PFLAG_PM_PENDING and calls ata_port_wait_eh() if this flag is set to
ensure that power management operations for a port are not scheduled
simultaneously. However, this flag check is done without holding the
port lock.
Fix this by taking the port lock on entry to the function and checking
the flag under this lock. The lock is released and re-taken if
ata_port_wait_eh() needs to be called. The two WARN_ON() macros checking
that the ATA_PFLAG_PM_PENDING flag was cleared are removed as the first
call is racy and the second one done without holding the port lock.
Fixes: 5ef4108291 ("ata: add ata port system PM callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58bfe2ccec upstream.
A user reported some issues with smaller file systems that get very
full. While investigating this issue I noticed that df wasn't showing
100% full, despite having 0 chunk space and having < 1MiB of available
metadata space.
This turns out to be an overflow issue, we're doing:
total_available_metadata_space - SZ_4M < global_block_rsv_size
to determine if there's not enough space to make metadata allocations,
which overflows if total_available_metadata_space is < 4M. Fix this by
checking to see if our available space is greater than the 4M threshold.
This makes df properly report 100% usage on the file system.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3914784553 upstream.
We have to unregister tco_pdev also if i2c_add_adapter() fails.
Fixes: 9424693035 ("i2c: i801: Create iTCO device on newer Intel PCHs")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ef6009235 upstream.
For REPORT SUPPORTED OPERATION CODES command, the service action field is
defined as bits 0-4 in the second byte in the CDB. Bits 5-7 in the second
byte are reserved.
Only look at the service action field in the second byte when determining
if the MAINTENANCE IN opcode is a REPORT SUPPORTED OPERATION CODES command.
This matches how we only look at the service action field in the second
byte when determining if the SERVICE ACTION IN(16) opcode is a READ
CAPACITY(16) command (reserved bits 5-7 in the second byte are ignored).
Fixes: 7b20309428 ("libata: Add support for SCT Write Same")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ee29facd8 upstream.
In nilfs_gccache_submit_read_data(), brelse(bh) is called to drop the
reference count of bh when the call to nilfs_dat_translate() fails. If
the reference count hits 0 and its owner page gets unlocked, bh may be
freed. However, bh->b_page is dereferenced to put the page after that,
which may result in a use-after-free bug. This patch moves the release
operation after unlocking and putting the page.
NOTE: The function in question is only called in GC, and in combination
with current userland tools, address translation using DAT does not occur
in that function, so the code path that causes this issue will not be
executed. However, it is possible to run that code path by intentionally
modifying the userland GC library or by calling the GC ioctl directly.
[konishi.ryusuke@gmail.com: NOTE added to the commit log]
Link: https://lkml.kernel.org/r/1543201709-53191-1-git-send-email-bianpan2016@163.com
Link: https://lkml.kernel.org/r/20230921141731.10073-1-konishi.ryusuke@gmail.com
Fixes: a3d93f709e ("nilfs2: block cache for garbage collection")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reported-by: Ferry Meng <mengferry@linux.alibaba.com>
Closes: https://lkml.kernel.org/r/20230818092022.111054-1-mengferry@linux.alibaba.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cce7fc8b29 upstream.
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef9b7bf52c upstream.
Daniel reported that the commit 1ae3e78c08 ("watchdog: iTCO_wdt: No
need to stop the timer in probe") makes QEMU implementation of the iTCO
watchdog not to trigger reboot anymore when NO_REBOOT flag is initially
cleared using this option (in QEMU command line):
-global ICH9-LPC.noreboot=false
The problem with the commit is that it left the unconditional setting of
NO_REBOOT that is not cleared anymore when the kernel keeps pinging the
watchdog (as opposed to the previous code that called iTCO_wdt_stop()
that cleared it).
Fix this so that we only set NO_REBOOT if the watchdog was not initially
running.
Fixes: 1ae3e78c08 ("watchdog: iTCO_wdt: No need to stop the timer in probe")
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221028062750.45451-1-mika.westerberg@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1ae3e78c08 upstream.
The watchdog core can handle pinging of the watchdog before userspace
opens the device. For this reason instead of stopping the timer, just
mark it as running and let the watchdog core take care of it.
Cc: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210921102900.61586-1-mika.westerberg@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 737dd811a3 ]
When a CRC error occurs, the HBA asserts an interrupt to indicate an
interface fatal error (PxIS.IFS). The ISR clears PxIE and PxIS, then
does error recovery. If the adapter receives another SDB FIS
with an error (PxIS.TFES) from the device before the start of the EH
recovery process, the interrupt signaling the new SDB cannot be
serviced as PxIE was cleared already. This in turn results in the HBA
inability to issue any command during the error recovery process after
setting PxCMD.ST to 1 because PxIS.TFES is still set.
According to AHCI 1.3.1 specifications section 6.2.2, fatal errors
notified by setting PxIS.HBFS, PxIS.HBDS, PxIS.IFS or PxIS.TFES will
cause the HBA to enter the ERR:Fatal state. In this state, the HBA
shall not issue any new commands.
To avoid this situation, introduce the function
ahci_port_clear_pending_irq() to clear pending interrupts before
executing a COMRESET. This follows the AHCI 1.3.1 - section 6.2.2.2
specification.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Fixes: e0bfd14997 ("[PATCH] ahci: stop engine during hard reset")
Cc: stable@vger.kernel.org
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93c7711494 ]
Drop pointless VPRINTK() calls for entering and existing interrupt
routines and convert the remaining calls to dev_dbg().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Stable-dep-of: 737dd811a3 ("ata: libahci: clear pending interrupt status")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f75f71b2c4 ]
Fix linker error if FB=m about missing fb_io_read and fb_io_write. The
linker's error message suggests that this config setting has already
been broken for other symbols.
All errors (new ones prefixed by >>):
sh4-linux-ld: drivers/video/fbdev/sh7760fb.o: in function `sh7760fb_probe':
sh7760fb.c:(.text+0x374): undefined reference to `framebuffer_alloc'
sh4-linux-ld: sh7760fb.c:(.text+0x394): undefined reference to `fb_videomode_to_var'
sh4-linux-ld: sh7760fb.c:(.text+0x39c): undefined reference to `fb_alloc_cmap'
sh4-linux-ld: sh7760fb.c:(.text+0x3a4): undefined reference to `register_framebuffer'
sh4-linux-ld: sh7760fb.c:(.text+0x3ac): undefined reference to `fb_dealloc_cmap'
sh4-linux-ld: sh7760fb.c:(.text+0x434): undefined reference to `framebuffer_release'
sh4-linux-ld: drivers/video/fbdev/sh7760fb.o: in function `sh7760fb_remove':
sh7760fb.c:(.text+0x800): undefined reference to `unregister_framebuffer'
sh4-linux-ld: sh7760fb.c:(.text+0x804): undefined reference to `fb_dealloc_cmap'
sh4-linux-ld: sh7760fb.c:(.text+0x814): undefined reference to `framebuffer_release'
>> sh4-linux-ld: drivers/video/fbdev/sh7760fb.o:(.rodata+0xc): undefined reference to `fb_io_read'
>> sh4-linux-ld: drivers/video/fbdev/sh7760fb.o:(.rodata+0x10): undefined reference to `fb_io_write'
sh4-linux-ld: drivers/video/fbdev/sh7760fb.o:(.rodata+0x2c): undefined reference to `cfb_fillrect'
sh4-linux-ld: drivers/video/fbdev/sh7760fb.o:(.rodata+0x30): undefined reference to `cfb_copyarea'
sh4-linux-ld: drivers/video/fbdev/sh7760fb.o:(.rodata+0x34): undefined reference to `cfb_imageblit'
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309130632.LS04CPWu-lkp@intel.com/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230918090400.13264-1-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80cc944eca ]
ata_scsi_port_error_handler() starts off by clearing ATA_PFLAG_EH_PENDING,
before calling ap->ops->error_handler() (without holding the ap->lock).
If an error IRQ is received while ap->ops->error_handler() is running,
the irq handler will set ATA_PFLAG_EH_PENDING.
Once ap->ops->error_handler() returns, ata_scsi_port_error_handler()
checks if ATA_PFLAG_EH_PENDING is set, and if it is, another iteration
of ATA EH is performed.
The problem is that ATA_PFLAG_EH_PENDING is not only cleared by
ata_scsi_port_error_handler(), it is also cleared by ata_eh_reset().
ata_eh_reset() is called by ap->ops->error_handler(). This additional
clearing done by ata_eh_reset() breaks the whole retry logic in
ata_scsi_port_error_handler(). Thus, if an error IRQ is received while
ap->ops->error_handler() is running, the port will currently remain
frozen and will never get re-enabled.
The additional clearing in ata_eh_reset() was introduced in commit
1e641060c4 ("libata: clear eh_info on reset completion").
Looking at the original error report:
https://marc.info/?l=linux-ide&m=124765325828495&w=2
We can see the following happening:
[ 1.074659] ata3: XXX port freeze
[ 1.074700] ata3: XXX hardresetting link, stopping engine
[ 1.074746] ata3: XXX flipping SControl
[ 1.411471] ata3: XXX irq_stat=400040 CONN|PHY
[ 1.411475] ata3: XXX port freeze
[ 1.420049] ata3: XXX starting engine
[ 1.420096] ata3: XXX rc=0, class=1
[ 1.420142] ata3: XXX clearing IRQs for thawing
[ 1.420188] ata3: XXX port thawed
[ 1.420234] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
We are not supposed to be able to receive an error IRQ while the port is
frozen (PxIE is set to 0, i.e. all IRQs for the port are disabled).
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) states:
"Each bit location can be thought of as reporting a '1' if the virtual
"interrupt line" for that port is indicating it wishes to generate an
interrupt. That is, if a port has one or more interrupt status bit set,
and the enables for those status bits are set, then this bit shall be set."
Additionally, AHCI state P:ComInit clearly shows that the state machine
will only jump to P:ComInitSetIS (which sets IS.IPS(x) to '1'), if PxIE.PCE
is set to '1'. In our case, PxIE is set to 0, so IS.IPS(x) won't get set.
So IS.IPS(x) only gets set if PxIS and PxIE is set.
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) also states:
"The bits in this register are read/write clear. It is set by the level of
the virtual interrupt line being a set, and cleared by a write of '1' from
the software."
So if IS.IPS(x) is set, you need to explicitly clear it by writing a 1 to
IS.IPS(x) for that port.
Since PxIE is cleared, the only way to get an interrupt while the port is
frozen, is if IS.IPS(x) is set, and the only way IS.IPS(x) can be set when
the port is frozen, is if it was set before the port was frozen.
However, since commit 737dd811a3 ("ata: libahci: clear pending interrupt
status"), we clear both PxIS and IS.IPS(x) after freezing the port, but
before the COMRESET, so the problem that commit 1e641060c4 ("libata:
clear eh_info on reset completion") fixed can no longer happen.
Thus, revert commit 1e641060c4 ("libata: clear eh_info on reset
completion"), so that the retry logic in ata_scsi_port_error_handler()
works once again. (The retry logic is still needed, since we can still
get an error IRQ _after_ the port has been thawed, but before
ata_scsi_port_error_handler() takes the ap->lock in order to check
if ATA_PFLAG_EH_PENDING is set.)
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6bd2c9248 ]
When user resize all trace ring buffer through file 'buffer_size_kb',
then in ring_buffer_resize(), kernel allocates buffer pages for each
cpu in a loop.
If the kernel preemption model is PREEMPT_NONE and there are many cpus
and there are many buffer pages to be allocated, it may not give up cpu
for a long time and finally cause a softlockup.
To avoid it, call cond_resched() after each cpu buffer allocation.
Link: https://lore.kernel.org/linux-trace-kernel/20230906081930.3939106-1-zhengyejian1@huawei.com
Cc: <mhiramat@kernel.org>
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4e4ada586 ]
Function instance_set() expects to enable event 'sched_switch', so we
should set 1 to its 'enable' file.
Testcase passed after this patch:
# ./ftracetest test.d/instances/instance-event.tc
=== Ftrace unit tests ===
[1] Test creation and deletion of trace instances while setting an event
[PASS]
# of passed: 1
# of failed: 0
# of unresolved: 0
# of untested: 0
# of unsupported: 0
# of xfailed: 0
# of undefined(test bug): 0
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb3255ee8f ]
Fix this makecheck warning:
drivers/parisc/sba_iommu.c:98:19: warning: symbol 'sba_list'
was not declared. Should it be static?
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f54d02c8f2 ]
Add function prototype for gunzip() to the boot library code and make
exit() and zalloc() static.
arch/xtensa/boot/lib/zmem.c:8:6: warning: no previous prototype for 'exit' [-Wmissing-prototypes]
8 | void exit (void)
arch/xtensa/boot/lib/zmem.c:13:7: warning: no previous prototype for 'zalloc' [-Wmissing-prototypes]
13 | void *zalloc(unsigned size)
arch/xtensa/boot/lib/zmem.c:35:6: warning: no previous prototype for 'gunzip' [-Wmissing-prototypes]
35 | void gunzip (void *dst, int dstlen, unsigned char *src, int *lenp)
Fixes: 4bedea9454 ("xtensa: Architecture support for Tensilica Xtensa Part 2")
Fixes: e7d163f766 ("xtensa: Removed local copy of zlib and fixed O= support")
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54d3d7d363 ]
Drop the -I<include-dir> options to prevent build warnings since there
is not boot/include directory:
cc1: warning: arch/xtensa/boot/include: No such file or directory [-Wmissing-include-dirs]
Fixes: 437374e9a9 ("restore arch/{ppc/xtensa}/boot cflags")
Fixes: 4bedea9454 ("xtensa: Architecture support for Tensilica Xtensa Part 2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-15-rdunlap@infradead.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a47b44fbb1 ]
tegra-bpmp clocks driver makes implicit conversion of signed error
code to unsigned value in recalc_rate operation. The behavior for
recalc_rate, according to it's specification, should be that "If the
driver cannot figure out a rate for this clock, it must return 0."
Fixes: ca6f2796ee ("clk: tegra: Add BPMP clock driver")
Signed-off-by: Timo Alho <talho@nvidia.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20230912112951.2330497-1-cyndis@kapsi.fi
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c0195fa9a ]
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac0 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b547b5e52a ]
If an error occurs after a successful irq_domain_add_linear() call, it
should be undone by a corresponding irq_domain_remove(), as already done
in the remove function.
Fixes: c6ce2b6bff ("gpio: add TB10x GPIO driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4920327601 ]
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Suggested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230918123011.1884401-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ff3ba4db5 ]
Valid domain value is in range 1 to HV_PERF_DOMAIN_MAX. Current code has
check for domain value greater than or equal to HV_PERF_DOMAIN_MAX. But
the check for domain value 0 is missing.
Fix this issue by adding check for domain value 0.
Before:
# ./perf stat -v -e hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ sleep 1
Using CPUID 00800200
Control descriptor is not initialized
Error:
The sys_perf_event_open() syscall returned with 5 (Input/output error) for
event (hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/).
/bin/dmesg | grep -i perf may provide additional information.
Result from dmesg:
[ 37.819387] hv-24x7: hcall failed: [0 0x60040000 0x100 0] => ret
0xfffffffffffffffc (-4) detail=0x2000000 failing ix=0
After:
# ./perf stat -v -e hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ sleep 1
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ event is not supported by the kernel.
failed to read counter hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/
Fixes: ebd4a5a3eb ("powerpc/perf/hv-24x7: Minor improvements")
Reported-by: Krishan Gopal Sarawast <krishang@linux.vnet.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Disha Goel <disgoel@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230825055601.360083-1-kjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0113d9c9d1 ]
Currently, we assume the skb is associated with a device before calling
__ip_options_compile, which is not always the case if it is re-routed by
ipvs.
When skb->dev is NULL, dev_net(skb->dev) will become null-dereference.
This patch adds a check for the edge case and switch to use the net_device
from the rtable when skb->dev is NULL.
Fixes: ed0de45a10 ("ipv4: recompile ip options in ipv4_link_failure")
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Kyle Zeng <zengyhkyle@gmail.com>
Cc: Stephen Suryaputra <ssuryaextr@gmail.com>
Cc: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd7d7ee3ba ]
With IPv6, connect() can occasionally return EINVAL if a route is
unavailable. If this happens during I/O to a data server, we want to
report it using LAYOUTERROR as an inability to connect.
Fixes: dd52128afd ("NFSv4.1/pnfs Ensure flexfiles reports all connection related errors")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 265b4da82d upstream.
The rsvp classifier has served us well for about a quarter of a century but has
has not been getting much maintenance attention due to lack of known users.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Kyle Zeng <zengyhkyle@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76e42ae831 upstream.
When fw_change() is called on an existing filter, the whole
tcf_result struct is always copied into the new instance of the filter.
This causes a problem when updating a filter bound to a class,
as tcf_unbind_filter() is always called on the old instance in the
success path, decreasing filter_cnt of the still referenced class
and allowing it to be deleted, leading to a use-after-free.
Fix this by no longer copying the tcf_result struct from the old filter.
Fixes: e35a8ee599 ("net: sched: fw use RCU")
Reported-by: valis <sec@valis.email>
Reported-by: Bing-Jhong Billy Jheng <billy@starlabs.sg>
Signed-off-by: valis <sec@valis.email>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: M A Ramdhan <ramdhan@starlabs.sg>
Link: https://lore.kernel.org/r/20230729123202.72406-3-jhs@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Fixed small conflict as 'fnew->ifindex' assignment is not protected by
CONFIG_NET_CLS_IND on upstream since a51486266c ]
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d53244186 upstream.
When the oob buffer length is not in multiple of words, the oob write
function does out-of-bounds read on the oob source buffer at the last
iteration. Fix that by always checking length limit on the oob buffer
read and fill with 0xff when reaching the end of the buffer to the oob
registers.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-5-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ec2839a90 upstream.
v7.2 controller has different ECC level field size and shift in the acc
control register than its predecessor and successor controller. It needs
to be set specifically.
Fixes: decba6d478 ("mtd: brcmnand: Add v7.2 controller support")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-2-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cc0a598b9 upstream.
If system is busy during the command status polling function, the driver
may not get the chance to poll the status register till the end of time
out and return the premature status. Do a final check after time out
happens to ensure reading the correct status.
Fixes: 9d2ee0a60b ("mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-3-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdd2630a73 upstream.
nfsd sends the transposed directory change info in the RENAME reply. The
source directory is in save_fh and the target is in current_fh.
Reported-by: Zhi Li <yieli@redhat.com>
Reported-by: Benjamin Coddington <bcodding@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2218844
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d1f903f75 upstream.
Changing the mode of symlinks is meaningless as the vfs doesn't take the
mode of a symlink into account during path lookup permission checking.
However, the vfs doesn't block mode changes on symlinks. This however,
has lead to an untenable mess roughly classifiable into the following
two categories:
(1) Filesystems that don't implement a i_op->setattr() for symlinks.
Such filesystems may or may not know that without i_op->setattr()
defined, notify_change() falls back to simple_setattr() causing the
inode's mode in the inode cache to be changed.
That's a generic issue as this will affect all non-size changing
inode attributes including ownership changes.
Example: afs
(2) Filesystems that fail with EOPNOTSUPP but change the mode of the
symlink nonetheless.
Some filesystems will happily update the mode of a symlink but still
return EOPNOTSUPP. This is the biggest source of confusion for
userspace.
The EOPNOTSUPP in this case comes from POSIX ACLs. Specifically it
comes from filesystems that call posix_acl_chmod(), e.g., btrfs via
if (!err && attr->ia_valid & ATTR_MODE)
err = posix_acl_chmod(idmap, dentry, inode->i_mode);
Filesystems including btrfs don't implement i_op->set_acl() so
posix_acl_chmod() will report EOPNOTSUPP.
When posix_acl_chmod() is called, most filesystems will have
finished updating the inode.
Perversely, this has the consequences that this behavior may depend
on two kconfig options and mount options:
* CONFIG_POSIX_ACL={y,n}
* CONFIG_${FSTYPE}_POSIX_ACL={y,n}
* Opt_acl, Opt_noacl
Example: btrfs, ext4, xfs
The only way to change the mode on a symlink currently involves abusing
an O_PATH file descriptor in the following manner:
fd = openat(-1, "/path/to/link", O_CLOEXEC | O_PATH | O_NOFOLLOW);
char path[PATH_MAX];
snprintf(path, sizeof(path), "/proc/self/fd/%d", fd);
chmod(path, 0000);
But for most major filesystems with POSIX ACL support such as btrfs,
ext4, ceph, tmpfs, xfs and others this will fail with EOPNOTSUPP with
the mode still updated due to the aforementioned posix_acl_chmod()
nonsense.
So, given that for all major filesystems this would fail with EOPNOTSUPP
and that both glibc (cf. [1]) and musl (cf. [2]) outright block mode
changes on symlinks we should just try and block mode changes on
symlinks directly in the vfs and have a clean break with this nonsense.
If this causes any regressions, we do the next best thing and fix up all
filesystems that do return EOPNOTSUPP with the mode updated to not call
posix_acl_chmod() on symlinks.
But as usual, let's try the clean cut solution first. It's a simple
patch that can be easily reverted. Not marking this for backport as I'll
do that manually if we're reasonably sure that this works and there are
no strong objections.
We could block this in chmod_common() but it's more appropriate to do it
notify_change() as it will also mean that we catch filesystems that
change symlink permissions explicitly or accidently.
Similar proposals were floated in the past as in [3] and [4] and again
recently in [5]. There's also a couple of bugs about this inconsistency
as in [6] and [7].
Link: https://sourceware.org/git/?p=glibc.git;a=blob;f=sysdeps/unix/sysv/linux/fchmodat.c;h=99527a3727e44cb8661ee1f743068f108ec93979;hb=HEAD [1]
Link: https://git.musl-libc.org/cgit/musl/tree/src/stat/fchmodat.c [2]
Link: https://lore.kernel.org/all/20200911065733.GA31579@infradead.org [3]
Link: https://sourceware.org/legacy-ml/libc-alpha/2020-02/msg00518.html [4]
Link: https://lore.kernel.org/lkml/87lefmbppo.fsf@oldenburg.str.redhat.com [5]
Link: https://sourceware.org/legacy-ml/libc-alpha/2020-02/msg00467.html [6]
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=14578#c17 [7]
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # please backport to all LTSes but not before v6.6-rc2 is tagged
Suggested-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Message-Id: <20230712-vfs-chmod-symlinks-v2-1-08cfb92b61dd@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df203da47f ]
There is a compile error when this commit is added:
md: raid1: fix potential OOB in raid1_remove_disk()
drivers/md/raid1.c: In function 'raid1_remove_disk':
drivers/md/raid1.c:1844:9: error: ISO C90 forbids mixed declarations
and code [-Werror=declaration-after-statement]
1844 | struct raid1_info *p = conf->mirrors + number;
| ^~~~~~
That's because the new code was inserted before the struct.
The change is move the struct command above this commit.
Fixes: 8b0472b50b ("md: raid1: fix potential OOB in raid1_remove_disk()")
Signed-off-by: Nigel Croxon <ncroxon@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/46d929d0-2aab-4cf2-b2bf-338963e8ba5a@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d0fe8c52b ]
When I register a kset in the following way:
static struct kset my_kset;
kobject_set_name(&my_kset.kobj, "my_kset");
ret = kset_register(&my_kset);
A null pointer dereference exception is occurred:
[ 4453.568337] Unable to handle kernel NULL pointer dereference at \
virtual address 0000000000000028
... ...
[ 4453.810361] Call trace:
[ 4453.813062] kobject_get_ownership+0xc/0x34
[ 4453.817493] kobject_add_internal+0x98/0x274
[ 4453.822005] kset_register+0x5c/0xb4
[ 4453.825820] my_kobj_init+0x44/0x1000 [my_kset]
... ...
Because I didn't initialize my_kset.kobj.ktype.
According to the description in Documentation/core-api/kobject.rst:
- A ktype is the type of object that embeds a kobject. Every structure
that embeds a kobject needs a corresponding ktype.
So add sanity check to make sure kset->kobj.ktype is not NULL.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20230805084114.1298-2-thunder.leizhen@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 801f287c93 ]
The function lio_target_nacl_info_show() uses sprintf() in a loop to print
details for every iSCSI connection in a session without checking for the
buffer length. With enough iSCSI connections it's possible to overflow the
buffer provided by configfs and corrupt the memory.
This patch replaces sprintf() with sysfs_emit_at() that checks for buffer
boundries.
Signed-off-by: Konstantin Shelekhin <k.shelekhin@yadro.com>
Link: https://lore.kernel.org/r/20230722152657.168859-2-k.shelekhin@yadro.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce9daa2efc ]
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20230628081511.186850-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e1796fd49 ]
It was completely unnecessary to use BUG in buffer_prepare().
Just replace it with an error return. This also fixes a smatch warning:
drivers/media/pci/cx23885/cx23885-video.c:422 buffer_prepare() error: uninitialized symbol 'ret'.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Niklas Cassel