commit ab8d66d132 upstream.
Two bitmasks in 'struct sdw_slave_prop' - 'source_ports' and
'sink_ports' - define which ports to program in
sdw_program_slave_port_params(). The masks are used to get the
appropriate data port properties ('struct sdw_get_slave_dpn_prop') from
an array.
Bitmasks can be non-continuous or can start from index different than 0,
thus when looking for matching port property for given port, we must
iterate over mask bits, not from 0 up to number of ports.
This fixes allocation and programming slave ports, when a source or sink
masks start from further index.
Fixes: f8101c74aa ("soundwire: Add Master and Slave port programming")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20240729140157.326450-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ee1b439b1 ]
For some reason, we add an offset to the PDI, presumably to skip the
PDI0 and PDI1 which are reserved for BPT.
This code is however completely wrong and leads to an out-of-bounds
access. We were just lucky so far since we used only a couple of PDIs
and remained within the PDI array bounds.
A Fixes: tag is not provided since there are no known platforms where
the out-of-bounds would be accessed, and the initial code had problems
as well.
A follow-up patch completely removes this useless offset.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326090122.1051806-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e199bf52ff upstream.
If bus is marked as multi_link, but number of masters in the stream is
not higher than bus->hw_sync_min_links (bus->multi_link && m_rt_count >=
bus->hw_sync_min_links), bank switching should not happen. The first
part of do_bank_switch() code properly takes these conditions into
account, but second part (sdw_ml_sync_bank_switch()) relies purely on
bus->multi_link property. This is not balanced and leads to NULL
pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Call trace:
wait_for_completion_timeout+0x124/0x1f0
do_bank_switch+0x370/0x6f8
sdw_prepare_stream+0x2d0/0x438
qcom_snd_sdw_prepare+0xa0/0x118
sm8450_snd_prepare+0x128/0x148
snd_soc_link_prepare+0x5c/0xe8
__soc_pcm_prepare+0x28/0x1ec
dpcm_be_dai_prepare+0x1e0/0x2c0
dpcm_fe_dai_prepare+0x108/0x28c
snd_pcm_do_prepare+0x44/0x68
snd_pcm_action_single+0x54/0xc0
snd_pcm_action_nonatomic+0xe4/0xec
snd_pcm_prepare+0xc4/0x114
snd_pcm_common_ioctl+0x1154/0x1cc0
snd_pcm_ioctl+0x54/0x74
Fixes: ce6e74d008 ("soundwire: Add support for multi link bank switch")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231124180136.390621-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c40d6b3249 ]
The soundwire subsystem uses two completion structures that allow
drivers to wait for soundwire device to become enumerated on the bus and
initialised by their drivers, respectively.
The code implementing the signalling is currently broken as it does not
signal all current and future waiters and also uses the wrong
reinitialisation function, which can potentially lead to memory
corruption if there are still waiters on the queue.
Not signalling future waiters specifically breaks sound card probe
deferrals as codec drivers can not tell that the soundwire device is
already attached when being reprobed. Some codec runtime PM
implementations suffer from similar problems as waiting for enumeration
during resume can also timeout despite the device already having been
enumerated.
Fixes: fb9469e54f ("soundwire: bus: fix race condition with enumeration_complete signaling")
Fixes: a90def0681 ("soundwire: bus: fix race condition with initialization_complete signaling")
Cc: stable@vger.kernel.org # 5.7
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230705123018.30903-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e557bca49b ]
In typical use cases, the peripheral becomes pm_runtime active as a
result of the ALSA/ASoC framework starting up a DAI. The parent/child
hierarchy guarantees that the manager device will be fully resumed
beforehand.
There is however a corner case where the manager device may become
pm_runtime active, but without ALSA/ASoC requesting any functionality
from the peripherals. In this case, the hardware peripheral device
will report as ATTACHED and its initialization routine will be
executed. If this initialization routine initiates any sort of
deferred processing, there is a possibility that the manager could
suspend without the peripheral suspend sequence being invoked: from
the pm_runtime framework perspective, the peripheral is *already*
suspended.
To avoid such disconnects between hardware state and pm_runtime state,
this patch adds an asynchronous pm_request_resume() upon successful
attach/initialization which will result in the proper resume/suspend
sequence to be followed on the peripheral side.
BugLink: https://github.com/thesofproject/linux/issues/3459
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220420023241.14335-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: c40d6b3249 ("soundwire: fix enumeration completion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0603a47bd3 ]
If wait_for_completion_timeout() times-out in _cdns_xfer_msg() it
is possible that something could have been written to the RX FIFO.
In this case, we should drain the RX FIFO so that anything in it
doesn't carry over and mess up the next transfer.
Obviously, if we got to this state something went wrong, and we
don't really know the state of everything. The cleanup in this
situation cannot be bullet-proof but we should attempt to avoid
breaking future transaction, if only to reduce the amount of
error noise when debugging the failure from a kernel log.
Note that this patch only implements the draining for blocking
(non-deferred) transfers. The deferred API doesn't have any proper
handling of error conditions and would need some re-design before
implementing cleanup. That is a task for a separate patch...
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221202161812.4186897-4-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 827c32d0df ]
The response_buf was declared much larger (128 entries) than the number
of responses that could ever be written into it. The Cadence IP is
configurable up to a maximum of 32 entries, and the datasheet says
that RX_FIFO_AVAIL can be 2 larger than this. So allow up to 34
responses.
Also add checking in cdns_read_response() to prevent overflowing
reponse_buf if RX_FIFO_AVAIL contains an unexpectedly large number.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221202161812.4186897-3-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8444560b4 upstream.
The HDAudio ASoC support relies on the set_tdm_slots() helper to store
the HDaudio stream tag in the tx_mask. This only works because of the
pre-existing order in soc-pcm.c, where the hw_params() is handled for
codec_dais *before* cpu_dais. When the order is reversed, the
stream_tag is used as a mask in the codec fixup functions:
/* fixup params based on TDM slot masks */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
codec_dai->tx_mask)
soc_pcm_codec_params_fixup(&codec_params,
codec_dai->tx_mask);
As a result of this confusion, the codec_params_fixup() ends-up
generating bad channel masks, depending on what stream_tag was
allocated.
We could add a flag to state that the tx_mask is really not a mask,
but it would be quite ugly to persist in overloading concepts.
Instead, this patch suggests a more generic get/set 'stream' API based
on the existing model for SoundWire. We can expand the concept to
store 'stream' opaque information that is specific to different DAI
types. In the case of HDAudio DAIs, we only need to store a stream tag
as an unsigned char pointer. The TDM rx_ and tx_masks should really
only be used to store masks.
Rename get_sdw_stream/set_sdw_stream callbacks and helpers as
get_stream/set_stream. No functionality change beyond the rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6867cda90 ]
The call to intel_register_dai() may fail because of memory allocation
issues or problems reported by the ASoC core. In all cases, when a
error is thrown the component is not registered, it's invalid to
unregister it.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220919175721.354679-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba05b39d26 ]
The buf passed in struct sdw_msg must only be written for a READ,
in that case the RDATA part of the response is the data value of the
register.
For a write command there is no RDATA, and buf should be assumed to
be const and unmodifable. The original caller should not expect its data
buffer to be corrupted by an sdw_nwrite().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220916103505.1562210-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df64077829 ]
The bus sdw_drv_remove() and sdw_drv_shutdown() helpers are used
conditionally, if the driver provides these routines.
These helpers already test if the driver provides a .remove or
.shutdown callback, so there's no harm in invoking the
sdw_drv_remove() and sdw_drv_shutdown() unconditionally.
In addition, the current code is imbalanced with
dev_pm_domain_attach() called from sdw_drv_probe(), but
dev_pm_domain_detach() called from sdw_drv_remove() only if the driver
provides a .remove callback.
Fixes: 9251345dca ("soundwire: Add SoundWire bus type")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610015105.25987-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75eac387a2 ]
link_id can be zero and if we have multiple controller instances
in a system like Qualcomm debugfs will end-up with duplicate namespace
resulting in incorrect debugfs entries.
Using bus-id and link-id combination should give a unique debugfs directory
entry and should fix below warning too.
"debugfs: Directory 'master-0' with parent 'soundwire' already present!"
Fixes: bf03473d5b ("soundwire: add debugfs support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210907105332.1257-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea6942dad4 ]
The power down sequence sets the link_up flag as false outside of the
mutex_lock. This is potentially unsafe.
In additional the flow in that sequence can be improved by first
testing if the link was powered, setting the link_up flag as false and
proceeding with the power down. In case the CPA bits cannot be
cleared, we only flag an error since we cannot deal with interrupts
any longer.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3e88e336 ]
In sdw_prep_deprep_slave_ports(), after the wait_for_completion()
the DP prepare status register is read. If this indicates that the
port is now prepared, the code should continue with the port setup.
It is irrelevant whether the wait_for_completion() timed out if the
port is now ready.
The previous implementation would always fail if the
wait_for_completion() timed out, even if the port was reporting
successful prepare.
This patch also fixes a minor bug where the return from sdw_read()
was not checked for error - any error code with LSBits clear could
be misinterpreted as a successful port prepare.
Fixes: 79df15b7d3 ("soundwire: Add helpers for ports operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210618144745.30629-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f17f96a8 ]
When stream config is failed, master runtime will release all
slave runtime in the slave_rt_list, but slave runtime is not
added to the list at this time. This patch frees slave runtime
in the config error path to fix the memory leak.
Fixes: 89e590535f ("soundwire: Add support for SoundWire stream management")
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Keyon Jie <yang.jie@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210331004610.12242-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f03690f4f6 ]
found flag is used to indicate SoundWire devices that are
both enumerated on the bus and available in the device list.
However this flag is not reset correctly after one iteration,
This could miss some of the devices that are enumerated on the
bus but not in device list. So reset this correctly to fix this issue!
Fixes: d52d7a1be0 ("soundwire: Add Slave status handling helpers")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210309104816.20350-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58ef935626 ]
We sometimes see COMMAND_IGNORED responses during the clock stop
sequence. It turns out we already have information if devices are
present on a link, so we should only prepare those when they
are attached.
In addition, even when COMMAND_IGNORED are received, we should still
proceed with the clock stop. The device will not be prepared but
that's not a problem.
The only case where the clock stop will fail is if the Cadence IP
reports an error (including a timeout), or if the devices throw a
COMMAND_FAILED response.
BugLink: https://github.com/thesofproject/linux/issues/2621
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210323013707.21455-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973794e856 ]
Intel stress-tests routinely report IO timeouts and invalid power
management transitions. Upon further analysis, we seem to be using the
wrong devices in pm_runtime calls.
Before reading and writing registers, we first need to make sure the
Slave is fully resumed. The existing code attempts to do such that,
however because of a confusion dating from 2017 and copy/paste, we
end-up resuming the parent only instead of resuming the codec device.
This can lead to accesses to the Slave registers while the bus is
still being configured and the Slave not enumerated, and as a result
IO errors occur.
This is a classic problem, similar confusions happened for HDaudio
between bus and codec device, leading to power management issues.
Fix by using the relevant device for all uses of pm_runtime functions.
Fixes: 60ee9be255 ('soundwire: bus: add PM/no-PM versions of read/write functions')
Fixes: aa79293517 ('soundwire: bus: fix io error when processing alert event')
Fixes: 9d715fa005 ('soundwire: Add IO transfer')
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210122070634.12825-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 299e9780b9 ]
When a Slave device is resumed, it may resume the bus and restart the
enumeration. During that process, we absolutely don't want to call
regular read/write routines which will wait for the resume to
complete, otherwise a deadlock occurs.
This patch fixes the same problem as the previous one, but is split to
make the life of linux-stable maintainers less painful.
Fixes: 29d158f906 ('soundwire: bus: initialize bus clock base and scale registers')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210122070634.12825-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b04c975e65 ]
When a Slave device is resumed, it may resume the bus and restart the
enumeration. During that process, we absolutely don't want to call
regular read/write routines which will wait for the resume to
complete, otherwise a deadlock occurs.
Fixes: 60ee9be255 ('soundwire: bus: add PM/no-PM versions of read/write functions')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210122070634.12825-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db9d9f944f ]
The existing code reports a NAK only when ACK=0
This is not aligned with the SoundWire 1.x specifications.
Table 32 in the SoundWire 1.2 specification shows that a Device shall
not set NAK=1 if ACK=1. But Table 33 shows the Combined Response
may very well be NAK=1/ACK=1, e.g. if another Device than the one
addressed reports a parity error.
NAK=1 signals a 'Command_Aborted', regardless of the ACK bit value.
Move the tests for NAK so that the NAK=1/ACK=1 combination is properly
detected according to the specification.
Fixes: 956baa1992 ('soundwire: cdns: Add sdw_master_ops and IO transfer support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e04e60fce4 ]
The 'master' device acts as a glue layer used during bus
initialization only, and it needs to be 'transparent' for pm_runtime
management. Its behavior should be that it becomes active when one of
its children becomes active, and suspends when all of its children are
suspended.
In our tests on Intel platforms, we routinely see these sort of
warnings on the initial boot:
[ 21.447345] rt715 sdw:3:25d:715:0: runtime PM trying to activate
child device sdw:3:25d:715:0 but parent (sdw-master-3) is not active
This is root-caused to a missing setup to make the device 'active' on
probe. Since we don't want the device to remain active forever after
the probe, the autosuspend configuration is also enabled at the end of
the probe - the device will actually autosuspend only in the case
where there are no devices physically attached. In practice, the
master device will suspend when all its children are no longer active.
Fixes: bd84256e86 ('soundwire: master: enable pm runtime')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201124130742.10986-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47edc0104c ]
Commit 5bd773242f ("soundwire: qcom: avoid dependency on
CONFIG_SLIMBUS") removed hard dependency on Slimbus for qcom driver but
it results in build failure when: CONFIG_SOUNDWIRE_QCOM=y
CONFIG_SLIMBUS=m
drivers/soundwire/qcom.o: In function `qcom_swrm_probe':
qcom.c:(.text+0xf44): undefined reference to `slimbus_bus'
Fix this by using IS_REACHABLE() in driver which is recommended to be
used with imply.
Fixes: 5bd773242f ("soundwire: qcom: avoid dependency on CONFIG_SLIMBUS")
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20201125055155.GD8403@vkoul-mobl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This round of update includes:
- Generic bandwidth allocation algorithm from Intel folks
- PM support for Intel chipsets
- Updates to Intel drivers which makes sdw usable on latest laptops
- Support for MMIO SDW controllers found in QC chipsets
- Update to subsystem to use helpers in bitfield.h to manage register
bits
-----BEGIN PGP SIGNATURE-----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=ALTw
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire updates for 5.10-rc1
This round of update includes:
- Generic bandwidth allocation algorithm from Intel folks
- PM support for Intel chipsets
- Updates to Intel drivers which makes sdw usable on latest laptops
- Support for MMIO SDW controllers found in QC chipsets
- Update to subsystem to use helpers in bitfield.h to manage register
bits
* tag 'soundwire-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (66 commits)
soundwire: sysfs: add slave status and device number before probe
soundwire: bus: add enumerated Slave device to device list
soundwire: remove an unnecessary NULL check
soundwire: cadence: add data port test fail interrupt
soundwire: intel: enable test modes
soundwire: enable Data Port test modes
soundwire: intel: use {u32|u16}p_replace_bits
soundwire: cadence: use u32p_replace_bits
soundwire: qcom: get max rows and cols info from compatible
soundwire: qcom: add support to block packing mode
soundwire: qcom: clear BIT FIELDs before value set.
soundwire: Add generic bandwidth allocation algorithm
soundwire: cadence: add parity error injection through debugfs
soundwire: bus: export broadcast read/write capability for tests
ASoC: codecs: realtek-soundwire: ignore initial PARITY errors
soundwire: bus: use quirk to filter out invalid parity errors
soundwire: slave: add first_interrupt_done status
soundwire: bus: filter-out unwanted interrupt reports
ASoC/soundwire: bus: use property to set interrupt masks
soundwire: qcom: fix SLIBMUS/SLIMBUS typo
...
The MIPI DisCo device properties that are read by the driver from
platform firmware, or hard-coded in the driver, should only be
provided as sysfs entries when a driver probes successfully.
However the device status and device number is updated even when there
is no driver present, and hence can be updated when a Slave device is
detected on the bus without being described in platform firmware and
without any driver registered/probed.
As suggested by GregKH, the attribute group for Slave status and
device number is is added by default upon device registration.
Credits to Vinod Koul for the status_show() function, shared in a
separate patch and used as is here. The status table was modified to
remove an unnecessary enum and status_show() is handled in a different
group attribute than what was suggested by Vinod.
Tested-by: Srinivas Kandgatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Co-developed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200924194430.121058-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently Slave devices are only added on startup, either from Device
Tree or ACPI entries. However Slave devices that are physically
present on the bus, but not described in platform firmware, will never
be added to the device list. The user/integrator can only know the
list of devices by looking a dynamic debug logs.
This patch suggests adding a Slave device even if there is no matching
DT or ACPI entry, so that we can see this in sysfs entry.
Initial code from Srinivas. Comments, fixes for ACPI probe and edits
of commit message by Pierre.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200924194430.121058-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The "bus" pointer isn't NULL so the address to a non-zero offset in
middle of "bus" cannot be NULL. Delete the NULL check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200923083235.GB1454948@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Master ports can report errors in test data modes, enable the
interrupt and just log a message. This capability is useful for Master
sink ports only (Master source ports generate data).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200920193207.31241-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds debugfs support to override the Master and Slave data
modes. The settings only take effect prior to a new stream being
prepared/enabled, or on resume.
The test mode can be set to verify data integrity and detect bus
clashes, but can only be used to test capture paths. In this case the
input generated by a Slave source port is replaced by a fixed or
cyclical patterns.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200920193207.31241-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Test modes are required for all SoundWire IP, and help debug
integration issues. In theory each port can be configured with a
different mode but to simplify this patch only offers separate
configurations for the Master and Slave ports - this covers 99% of the
intended cases during platform integration.
The test mode value is set via platform-specific ways.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200920193207.31241-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
FIELD_PREP() does not replace the bits so it is not apt in case where we
modify a register.
Use u32_replace_bits() or u16_replace_bits() instead.
Fixes: 3b4979cabd ("soundwire: intel: use FIELD_{GET|PREP}")
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200917120146.1780323-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
FIELD_PREP() does not replace the bits so it is not apt in case where we
modify a register.
Use u32p_replace_bits() instead.
Fixes: 3cf25d63b1 ("soundwire: cadence: use FIELD_{GET|PREP}")
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200917120146.1780323-2-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
currently the max rows and cols values are hardcoded. In reality
these values depend on the IP version. So get these based on
device tree compatible strings.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200917120138.11313-4-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to usage (bitfields.h) of REG_FIELDS,
Modify is:
reg &= ~REG_FIELD_C;
reg |= FIELD_PREP(REG_FIELD_C, c);
Patch ("soundwire: qcom : use FIELD_{GET|PREP}") seems to have
accidentally removed clearing bit field while modifying the register.
Fix this by using u32p_replace_bits() to clear and set the values.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200917120138.11313-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This algorithm computes bus parameters like clock frequency, frame
shape and port transport parameters based on active stream(s) running
on the bus.
Developers can also implement their own .compute_params() callback for
specific resource management algorithm, and set if before calling
sdw_add_bus_master()
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah. All hard-coded
values were removed from the initial contribution to use BIOS
information instead.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200908131520.5712-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Cadence IP can inject errors, let's make use of this capability to
test Slave parity error checks.
See e.g. example log where both the master and slave detect the parity
error injected on a dummy read command.
cd /sys/kernel/debug/soundwire/master-1/intel-sdw/
echo 1 > cdns-parity-error-injection
[ 44.756249] intel-master sdw-master-1: Parity error
[ 44.756313] intel-master sdw-master-1: Msg NACK received
[ 44.756366] intel-master sdw-master-1: Msg NACKed for Slave 15
[ 44.756375] intel-master sdw-master-1: trf on Slave 15 failed:-5
[ 44.756382] intel-master sdw-master-1: parity error injection, read: -5
[ 44.756649] rt1308 sdw:1:25d:1308:0: Parity error detected
The code makes sure the Master device is resumed, hence the clock
restarted, before sending a parity error.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Provide prototype and export symbol to enable tests. The bus lock is
handled externally to avoid conflicts e.g. between kernel-generated
traffic and test traffic.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If a Slave device reports with a quirk that its initial parity check
may be incorrect, filter it but keep the parity checks active in
steady state.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some Slaves report incorrect information in their interrupt status
registers after a master/bus reset, track the initial interrupt
handling so that quirks can be introduced to filter out incorrect
information while keeping interrupts enabled in steady state.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Unlike the traditional usage, in the SoundWire specification the
interrupt masks only gate the propagation of an interrupt condition to
the PING frame status. They do not gate the changes of the INT_STAT
registers, which will happen regardless of the mask settings. See
Figure 116 of the SoundWire 1.2 specification for an in-depth
description of the interrupt model.
When the bus driver reads the SCP_INT1_STAT register, it will retrieve
all the interrupt status, including for the mask fields that were not
explicitly set. For example, even if the PARITY mask is not set, the
PARITY error status will be reported if an implementation-defined
interrupt for jack detection is enabled and occurs.
Filtering undesired interrupt reports and handling has to be
implemented in software. This patch enables this filtering for the
INT1_IMPL_DEF, PARITY and BUS_CLASH interrupt sources.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a slave-level property and program the SCP_INT1_MASK as desired by
the codec driver. Since there is no DisCo property this has to be an
implementation-specific firmware property or hard-coded in the driver.
The only functionality change is that implementation-defined
interrupts are no longer set for amplifiers - those interrupts are
typically for jack detection or acoustic event detection/hotwording.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200908134521.6781-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix slimbus case being broken thanks to a typo.
Fixes: 5bd773242f ("soundwire: qcom: avoid dependency on CONFIG_SLIMBUS")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200908140818.28373-1-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In system suspend stress cases, the SOF CI reports timeouts. The root
cause is that an alert is generated while the system suspends. The
interrupt handling generates transactions on the bus that will never
be handled because the interrupts are disabled in parallel.
As a result, the transaction never completes and times out on resume.
This error doesn't seem too problematic since it happens in a work
queue, and the system recovers without issues.
Nevertheless, this race condition should not happen. When doing a
system suspend, or when disabling interrupts, we should make sure the
current transaction can complete, and prevent new work from being
queued.
BugLink: https://github.com/thesofproject/linux/issues/2344
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200817222340.18042-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a compatible string for HW version v1.5.1 on sm8250 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200905173905.16541-5-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
