[ Upstream commit 30a92c9e3d ]
Open vSwitch is originally intended to switch at layer 2, only dealing with
Ethernet frames. With the introduction of l3 tunnels support, it crossed
into the realm of needing to care a bit about some routing details when
making forwarding decisions. If an oversized packet would need to be
fragmented during this forwarding decision, there is a chance for pmtu
to get involved and generate a routing exception. This is gated by the
skbuff->pkt_type field.
When a flow is already loaded into the openvswitch module this field is
set up and transitioned properly as a packet moves from one port to
another. In the case that a packet execute is invoked after a flow is
newly installed this field is not properly initialized. This causes the
pmtud mechanism to omit sending the required exception messages across
the tunnel boundary and a second attempt needs to be made to make sure
that the routing exception is properly setup. To fix this, we set the
outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get
to the openvswitch module via a port device or packet command.
Even for bridge ports as users, the pkt_type needs to be reset when
doing the transmit as the packet is truly outgoing and routing needs
to get involved post packet transformations, in the case of
VXLAN/GENEVE/udp-tunnel packets. In general, the pkt_type on output
gets ignored, since we go straight to the driver, but in the case of
tunnel ports they go through IP routing layer.
This issue is periodically encountered in complex setups, such as large
openshift deployments, where multiple sets of tunnel traversal occurs.
A way to recreate this is with the ovn-heater project that can setup
a networking environment which mimics such large deployments. We need
larger environments for this because we need to ensure that flow
misses occur. In these environment, without this patch, we can see:
./ovn_cluster.sh start
podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200
podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142)
--- 21.0.0.3 ping statistics ---
...
Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not
sent into the server.
With this patch, setting the pkt_type, we see the following:
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222)
ping: local error: message too long, mtu=1222
--- 21.0.0.3 ping statistics ---
...
In this case, the first ping request receives the FRAG_NEEDED message and
a local routing exception is created.
Tested-by: Jaime Caamano <jcaamano@redhat.com>
Reported-at: https://issues.redhat.com/browse/FDP-164
Fixes: 58264848a5 ("openvswitch: Add vxlan tunneling support.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240516200941.16152-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c988176b6 ]
OVS_PACKET_CMD_EXECUTE has 3 main attributes:
- OVS_PACKET_ATTR_KEY - Packet metadata in a netlink format.
- OVS_PACKET_ATTR_PACKET - Binary packet content.
- OVS_PACKET_ATTR_ACTIONS - Actions to execute on the packet.
OVS_PACKET_ATTR_KEY is parsed first to populate sw_flow_key structure
with the metadata like conntrack state, input port, recirculation id,
etc. Then the packet itself gets parsed to populate the rest of the
keys from the packet headers.
Whenever the packet parsing code starts parsing the ICMPv6 header, it
first zeroes out fields in the key corresponding to Neighbor Discovery
information even if it is not an ND packet.
It is an 'ipv6.nd' field. However, the 'ipv6' is a union that shares
the space between 'nd' and 'ct_orig' that holds the original tuple
conntrack metadata parsed from the OVS_PACKET_ATTR_KEY.
ND packets should not normally have conntrack state, so it's fine to
share the space, but normal ICMPv6 Echo packets or maybe other types of
ICMPv6 can have the state attached and it should not be overwritten.
The issue results in all but the last 4 bytes of the destination
address being wiped from the original conntrack tuple leading to
incorrect packet matching and potentially executing wrong actions
in case this packet recirculates within the datapath or goes back
to userspace.
ND fields should not be accessed in non-ND packets, so not clearing
them should be fine. Executing memset() only for actual ND packets to
avoid the issue.
Initializing the whole thing before parsing is needed because ND packet
may not contain all the options.
The issue only affects the OVS_PACKET_CMD_EXECUTE path and doesn't
affect packets entering OVS datapath from network interfaces, because
in this case CT metadata is populated from skb after the packet is
already parsed.
Fixes: 9dd7f8907c ("openvswitch: Add original direction conntrack tuple to sw_flow_key.")
Reported-by: Antonin Bas <antonin.bas@broadcom.com>
Closes: https://github.com/openvswitch/ovs-issues/issues/327
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240509094228.1035477-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ea7b72d4f ]
Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal
of ovs_ct_limit_exit, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 11efd5cb04 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4539f91f2a ]
On startup, ovs-vswitchd probes different datapath features including
support for timeout policies. While probing, it tries to execute
certain operations with OVS_PACKET_ATTR_PROBE or OVS_FLOW_ATTR_PROBE
attributes set. These attributes tell the openvswitch module to not
log any errors when they occur as it is expected that some of the
probes will fail.
For some reason, setting the timeout policy ignores the PROBE attribute
and logs a failure anyway. This is causing the following kernel log
on each re-start of ovs-vswitchd:
kernel: Failed to associated timeout policy `ovs_test_tp'
Fix that by using the same logging macro that all other messages are
using. The message will still be printed at info level when needed
and will be rate limited, but with a net rate limiter instead of
generic printk one.
The nf_ct_set_timeout() itself will still print some info messages,
but at least this change makes logging in openvswitch module more
consistent.
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240403203803.2137962-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e2f90d31f ]
The ovs module allows for some actions to recursively contain an action
list for complex scenarios, such as sampling, checking lengths, etc.
When these actions are copied into the internal flow table, they are
evaluated to validate that such actions make sense, and these calls
happen recursively.
The ovs-vswitchd userspace won't emit more than 16 recursion levels
deep. However, the module has no such limit and will happily accept
limits larger than 16 levels nested. Prevent this by tracking the
number of recursions happening and manually limiting it to 16 levels
nested.
The initial implementation of the sample action would track this depth
and prevent more than 3 levels of recursion, but this was removed to
support the clone use case, rather than limited at the current userspace
limit.
Fixes: 798c166173 ("openvswitch: Optimize sample action for the clone use cases")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240207132416.1488485-2-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2fa28f5c6f upstream.
old_meter needs to be free after it is detached regardless of whether
the new meter is successfully attached.
Fixes: c7c4c44c9a ("net: openvswitch: expand the meters supported number")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68bb10101e ]
The commit mentioned below causes the ovs_flow_tbl_lookup() function
to be called with the masked key. However, it's supposed to be called
with the unmasked key. This due to the fact that the datapath supports
installing wider flows, and OVS relies on this behavior. For example
if ipv4(src=1.1.1.1/192.0.0.0, dst=1.1.1.2/192.0.0.0) exists, a wider
flow (smaller mask) of ipv4(src=192.1.1.1/128.0.0.0,dst=192.1.1.2/
128.0.0.0) is allowed to be added.
However, if we try to add a wildcard rule, the installation fails:
$ ovs-appctl dpctl/add-flow system@myDP "in_port(1),eth_type(0x0800), \
ipv4(src=1.1.1.1/192.0.0.0,dst=1.1.1.2/192.0.0.0,frag=no)" 2
$ ovs-appctl dpctl/add-flow system@myDP "in_port(1),eth_type(0x0800), \
ipv4(src=192.1.1.1/0.0.0.0,dst=49.1.1.2/0.0.0.0,frag=no)" 2
ovs-vswitchd: updating flow table (File exists)
The reason is that the key used to determine if the flow is already
present in the system uses the original key ANDed with the mask.
This results in the IP address not being part of the (miniflow) key,
i.e., being substituted with an all-zero value. When doing the actual
lookup, this results in the key wrongfully matching the first flow,
and therefore the flow does not get installed.
This change reverses the commit below, but rather than having the key
on the stack, it's allocated.
Fixes: 190aa3e778 ("openvswitch: Fix Frame-size larger than 1024 bytes warning.")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52d1aa8b82 ]
nf_conn:mark can be read from and written to in parallel. Use
READ_ONCE()/WRITE_ONCE() for reads and writes to prevent unwanted
compiler optimizations.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd954cc191 ]
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com
Fixes: 44da5ae5fb ("openvswitch: Drop user features if old user space attempted to create datapath")
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21ab2afa2 ]
Currently queue_userspace_packet will call kfree_skb for all frames,
whether or not an error occurred. This can result in a single dropped
frame being reported as multiple drops in dropwatch. This functions
caller may also call kfree_skb in case of an error. This patch will
consume the skbs instead and allow caller's to use kfree_skb.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109957
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1100248a5c ]
Frames sent to userspace can be reported as dropped in
ovs_dp_process_packet, however, if they are dropped in the netlink code
then netlink_attachskb will report the same frame as dropped.
This patch checks for error codes which indicate that the frame has
already been freed.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109946
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 12378a5a75 upstream.
When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.
As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.
This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.
The offending commit is partially reverted to restore the expected
behavior.
The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.
Cc: stable@vger.kernel.org
Fixes: fa642f0883 ("openvswitch: Derive IP protocol number for IPv6 later frags")
Link: https://docs.openvswitch.org/en/latest/topics/design/#fragments
Signed-off-by: Rosemarie O'Riorden <roriorden@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2061ecfdf2 upstream.
If packet headers changed, the cached nfct is no longer relevant
for the packet and attempt to re-use it leads to the incorrect packet
classification.
This issue is causing broken connectivity in OpenStack deployments
with OVS/OVN due to hairpin traffic being unexpectedly dropped.
The setup has datapath flows with several conntrack actions and tuple
changes between them:
actions:ct(commit,zone=8,mark=0/0x1,nat(src)),
set(eth(src=00:00:00:00:00:01,dst=00:00:00:00:00:06)),
set(ipv4(src=172.18.2.10,dst=192.168.100.6,ttl=62)),
ct(zone=8),recirc(0x4)
After the first ct() action the packet headers are almost fully
re-written. The next ct() tries to re-use the existing nfct entry
and marks the packet as invalid, so it gets dropped later in the
pipeline.
Clearing the cached conntrack entry whenever packet tuple is changed
to avoid the issue.
The flow key should not be cleared though, because we should still
be able to match on the ct_state if the recirculation happens after
the tuple change but before the next ct() action.
Cc: stable@vger.kernel.org
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
Reported-by: Frode Nordahl <frode.nordahl@canonical.com>
Link: https://mail.openvswitch.org/pipermail/ovs-discuss/2022-May/051829.html
Link: https://bugs.launchpad.net/ubuntu/+source/ovn/+bug/1967856
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/r/20220606221140.488984-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[Backport to 5.10: minor rebase in ovs_ct_clear function.
This version also applicable to and tested on 5.4 and 4.19.]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefa91b233 upstream.
Given a sufficiently large number of actions, while copying and
reserving memory for a new action of a new flow, if next_offset is
greater than MAX_ACTIONS_BUFSIZE, the function reserve_sfa_size() does
not return -EMSGSIZE as expected, but it allocates MAX_ACTIONS_BUFSIZE
bytes increasing actions_len by req_size. This can then lead to an OOB
write access, especially when further actions need to be copied.
Fix it by rearranging the flow action size check.
KASAN splat below:
==================================================================
BUG: KASAN: slab-out-of-bounds in reserve_sfa_size+0x1ba/0x380 [openvswitch]
Write of size 65360 at addr ffff888147e4001c by task handler15/836
CPU: 1 PID: 836 Comm: handler15 Not tainted 5.18.0-rc1+ #27
...
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x5a
print_report.cold+0x5e/0x5db
? __lock_text_start+0x8/0x8
? reserve_sfa_size+0x1ba/0x380 [openvswitch]
kasan_report+0xb5/0x130
? reserve_sfa_size+0x1ba/0x380 [openvswitch]
kasan_check_range+0xf5/0x1d0
memcpy+0x39/0x60
reserve_sfa_size+0x1ba/0x380 [openvswitch]
__add_action+0x24/0x120 [openvswitch]
ovs_nla_add_action+0xe/0x20 [openvswitch]
ovs_ct_copy_action+0x29d/0x1130 [openvswitch]
? __kernel_text_address+0xe/0x30
? unwind_get_return_address+0x56/0xa0
? create_prof_cpu_mask+0x20/0x20
? ovs_ct_verify+0xf0/0xf0 [openvswitch]
? prep_compound_page+0x198/0x2a0
? __kasan_check_byte+0x10/0x40
? kasan_unpoison+0x40/0x70
? ksize+0x44/0x60
? reserve_sfa_size+0x75/0x380 [openvswitch]
__ovs_nla_copy_actions+0xc26/0x2070 [openvswitch]
? __zone_watermark_ok+0x420/0x420
? validate_set.constprop.0+0xc90/0xc90 [openvswitch]
? __alloc_pages+0x1a9/0x3e0
? __alloc_pages_slowpath.constprop.0+0x1da0/0x1da0
? unwind_next_frame+0x991/0x1e40
? __mod_node_page_state+0x99/0x120
? __mod_lruvec_page_state+0x2e3/0x470
? __kasan_kmalloc_large+0x90/0xe0
ovs_nla_copy_actions+0x1b4/0x2c0 [openvswitch]
ovs_flow_cmd_new+0x3cd/0xb10 [openvswitch]
...
Cc: stable@vger.kernel.org
Fixes: f28cd2af22 ("openvswitch: fix flow actions reallocation")
Signed-off-by: Paolo Valerio <pvalerio@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f30fb9166 ]
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 34ae932a40 ("openvswitch: Make tunnel set action attach a metadata dst")
Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f2a3050b4 ]
'OVS_CLONE_ATTR_EXEC' is an internal attribute that is used for
performance optimization inside the kernel. It's added by the kernel
while parsing user-provided actions and should not be sent during the
flow dump as it's not part of the uAPI.
The issue doesn't cause any significant problems to the ovs-vswitchd
process, because reported actions are not really used in the
application lifecycle and only supposed to be shown to a human via
ovs-dpctl flow dump. However, the action list is still incorrect
and causes the following error if the user wants to look at the
datapath flows:
# ovs-dpctl add-dp system@ovs-system
# ovs-dpctl add-flow "<flow match>" "clone(ct(commit),0)"
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(bad length 4, expected -1 for: action0(01 00 00 00),
ct(commit),0)
With the fix:
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(ct(commit),0)
Additionally fixed an incorrect attribute name in the comment.
Fixes: b233504033 ("openvswitch: kernel datapath clone action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20220404104150.2865736-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f19c44452b upstream.
IPv6 nd target mask was not getting populated in flow dump.
In the function __ovs_nla_put_key the icmp code mask field was checked
instead of icmp code key field to classify the flow as neighbour discovery.
ufid:bdfbe3e5-60c2-43b0-a5ff-dfcac1c37328, recirc_id(0),dp_hash(0/0),
skb_priority(0/0),in_port(ovs-nm1),skb_mark(0/0),ct_state(0/0),
ct_zone(0/0),ct_mark(0/0),ct_label(0/0),
eth(src=00:00:00:00:00:00/00:00:00:00:00:00,
dst=00:00:00:00:00:00/00:00:00:00:00:00),
eth_type(0x86dd),
ipv6(src=::/::,dst=::/::,label=0/0,proto=58,tclass=0/0,hlimit=0/0,frag=no),
icmpv6(type=135,code=0),
nd(target=2001::2/::,
sll=00:00:00:00:00:00/00:00:00:00:00:00,
tll=00:00:00:00:00:00/00:00:00:00:00:00),
packets:10, bytes:860, used:0.504s, dp:ovs, actions:ovs-nm2
Fixes: e64457191a (openvswitch: Restructure datapath.c and flow.c)
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Link: https://lore.kernel.org/r/20220328054148.3057-1-martinvarghesenokia@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60b44ca6bd ]
During NAT, a tuple collision may occur. When this happens, openvswitch
will make a second pass through NAT which will perform additional packet
modification. This will update the skb data, but not the flow key that
OVS uses. This means that future flow lookups, and packet matches will
have incorrect data. This has been supported since
5d50aa83e2 ("openvswitch: support asymmetric conntrack").
That commit failed to properly update the sw_flow_key attributes, since
it only called the ovs_ct_nat_update_key once, rather than each time
ovs_ct_nat_execute was called. As these two operations are linked, the
ovs_ct_nat_execute() function should always make sure that the
sw_flow_key is updated after a successful call through NAT infrastructure.
Fixes: 5d50aa83e2 ("openvswitch: support asymmetric conntrack")
Cc: Dumitru Ceara <dceara@redhat.com>
Cc: Numan Siddique <nusiddiq@redhat.com>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220318124319.3056455-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01634047bf ]
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4df1b0c24 ]
We have observed meters working unexpected if traffic is 3+Gbit/s
with multiple connections.
now_ms is not pretected by meter->lock, we may get a negative
long_delta_ms when another cpu updated meter->used, then:
delta_ms = (u32)long_delta_ms;
which will be a large value.
band->bucket += delta_ms * band->rate;
then we get a wrong band->bucket.
OpenVswitch userspace datapath has fixed the same issue[1] some
time ago, and we port the implementation to kernel datapath.
[1] https://patchwork.ozlabs.org/project/openvswitch/patch/20191025114436.9746-1-i.maximets@ovn.org/
Fixes: 96fbc13d7e ("openvswitch: Add meter infrastructure")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Suggested-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d51419d49 ]
'struct ovs_zone_limit' has more members than initialized in
ovs_ct_limit_get_default_limit(). The rest of the memory is a random
kernel stack content that ends up being sent to userspace.
Fix that by using designated initializer that will clear all
non-specified fields.
Fixes: 11efd5cb04 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09d6217254 ]
Currently, the exception actions are not processed correctly as the wrong
dataset is passed. This change fixes this, including the misleading
comment.
In addition, a check was added to make sure we work on an IPv4 packet,
and not just assume if it's not IPv6 it's IPv4.
This was all tested using OVS with patch,
https://patchwork.ozlabs.org/project/openvswitch/list/?series=21639,
applied and sending packets with a TTL of 1 (and 0), both with IPv4
and IPv6.
Fixes: 69929d4c49 ("net: openvswitch: fix TTL decrement action netlink message format")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/160733569860.3007.12938188180387116741.stgit@wsfd-netdev64.ntdv.lab.eng.bos.redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Changing 'return start' to 'return action_start' can fix this bug.
Fixes: 69929d4c49 ("net: openvswitch: fix TTL decrement action netlink message format")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20201204114314.1596-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
when openvswitch is configured to mangle the LSE, the current value is
read from the packet dereferencing 4 bytes at mpls_hdr(): ensure that
the label is contained in the skb "linear" area.
Found by code inspection.
Fixes: d27cf5c59a ("net: core: add MPLS update core helper and use in OvS")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/aa099f245d93218b84b5c056b67b6058ccf81a66.1606987185.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the openvswitch module is not accepting the correctly formated
netlink message for the TTL decrement action. For both setting and getting
the dec_ttl action, the actions should be nested in the
OVS_DEC_TTL_ATTR_ACTION attribute as mentioned in the openvswitch.h uapi.
When the original patch was sent, it was tested with a private OVS userspace
implementation. This implementation was unfortunately not upstreamed and
reviewed, hence an erroneous version of this patch was sent out.
Leaving the patch as-is would cause problems as the kernel module could
interpret additional attributes as actions and vice-versa, due to the
actions not being encapsulated/nested within the actual attribute, but
being concatinated after it.
Fixes: 744676e777 ("openvswitch: add TTL decrement action")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/160622121495.27296.888010441924340582.stgit@wsfd-netdev64.ntdv.lab.eng.bos.redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The flow_lookup() function uses per CPU variables, which must be called
with BH disabled. However, this is fine in the general NAPI use case
where the local BH is disabled. But, it's also called from the netlink
context. The below patch makes sure that even in the netlink path, the
BH is disabled.
In addition, u64_stats_update_begin() requires a lock to ensure one writer
which is not ensured here. Making it per-CPU and disabling NAPI (softirq)
ensures that there is always only one writer.
Fixes: eac87c413b ("net: openvswitch: reorder masks array based on usage")
Reported-by: Juri Lelli <jlelli@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/160295903253.7789.826736662555102345.stgit@ebuild
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With multiple DNAT rules it's possible that after destination
translation the resulting tuples collide.
For example, two openvswitch flows:
nw_dst=10.0.0.10,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
nw_dst=10.0.0.20,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
Assuming two TCP clients initiating the following connections:
10.0.0.10:5000->10.0.0.10:10
10.0.0.10:5000->10.0.0.20:10
Both tuples would translate to 10.0.0.10:5000->20.0.0.1:20 causing
nf_conntrack_confirm() to fail because of tuple collision.
Netfilter handles this case by allocating a null binding for SNAT at
egress by default. Perform the same operation in openvswitch for DNAT
if no explicit SNAT is requested by the user and allocate a null binding
for SNAT for packets in the "original" direction.
Reported-at: https://bugzilla.redhat.com/1877128
Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: 05752523e5 ("openvswitch: Interface with NAT.")
Signed-off-by: Dumitru Ceara <dceara@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only usage of these is to assign their address to the small_ops field
in the genl_family struct, which is a const pointer, and applying
ARRAY_SIZE() on them. Make them const to allow the compiler to put them
in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement TCA_VLAN_ACT_POP_ETH and TCA_VLAN_ACT_PUSH_ETH, to
respectively pop and push a base Ethernet header at the beginning of a
frame.
POP_ETH is just a matter of pulling ETH_HLEN bytes. VLAN tags, if any,
must be stripped before calling POP_ETH.
PUSH_ETH is restricted to skbs with no mac_header, and only the MAC
addresses can be configured. The Ethertype is automatically set from
skb->protocol. These restrictions ensure that all skb's fields remain
consistent, so that this action can't confuse other part of the
networking stack (like GSO).
Since openvswitch already had these actions, consolidate the code in
skbuff.c (like for vlan and mpls push/pop).
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function ovs_ct_limit_exit, there is already a helper vaibale
which could be reused to improve the readability, so i fix it in this
patch.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If nf_conncount_init fails currently the dispatched work is not canceled,
causing problems when the timer fires. This change fixes this by not
scheduling the work until all initialization is successful.
Fixes: a65878d6f0 ("net: openvswitch: fixes potential deadlock in dp cleanup code")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
keep_flows was introduced by [1], which used as flag to delete flows or not.
When rehashing or expanding the table instance, we will not flush the flows.
Now don't use it anymore, remove it.
[1] - acd051f176
Cc: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decrease table->count and ufid_count unconditionally,
because we only don't use count or ufid_count to count
when flushing the flows. To simplify the codes, we
remove the "count" argument of table_instance_flow_free.
To avoid a bug when deleting flows in the future, add
WARN_ON in flush flows function.
Cc: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not change the logic, just improve the coding style.
Cc: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using ipv6_stub->ipv6_fragment to avoid the netfilter dependency
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid some issues, for example RCU usage warning and double free,
we should flush the flows under ovs_lock. This patch refactors
table_instance_destroy and introduces table_instance_flow_flush
which can be invoked by __dp_destroy or ovs_flow_tbl_flush.
Fixes: 50b0e61b32 ("net: openvswitch: fix possible memleak on destroy flow-table")
Reported-by: Johan Knöös <jknoos@google.com>
Reported-at: https://mail.openvswitch.org/pipermail/ovs-discuss/2020-August/050489.html
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ovs_flow_tbl_destroy always is called from RCU callback
or error path. It is no need to check if rcu_read_lock
or lockdep_ovsl_is_held was held.
ovs_dp_cmd_fill_info always is called with ovs_mutex,
So use the rcu_dereference_ovsl instead of rcu_dereference
in ovs_flow_tbl_masks_cache_size.
Fixes: 9bf24f594c ("net: openvswitch: make masks cache size configurable")
Cc: Eelco Chaudron <echaudro@redhat.com>
Reported-by: syzbot+c0eb9e7cdde04e4eb4be@syzkaller.appspotmail.com
Reported-by: syzbot+f612c02823acb02ff9bc@syzkaller.appspotmail.com
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the masks cache size configurable, or with
a size of 0, disable it.
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a counter that counts the number of masks cache hits, and
export it through the megaflow netlink statistics.
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Conole