[ Upstream commit 5f76955ab1 ]
The commit 26623eea0d attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.
Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.
Fixes: 26623eea0d ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4920d42ce upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26623eea0d ]
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stmfts_input_open, so we should fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220317131604.53538-1-zhengyongjun3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ACPI/x86 devices with a Cherry Trail SoC should have a GpioInt + a regular
GPIO ACPI resource in their ACPI tables.
Some CHT devices have a bug, where the also is bogus interrupt resource
(likely copied from a previous Bay Trail based generation of the device).
The i2c-core-acpi code will assign the bogus, non-working, interrupt
resource to client->irq. Add a workaround to fix this up.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2043960
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220228111613.363336-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc4' into for-linus
Merge with mainline to get the Intel ASoC generic helpers header and
other changes.
This driver works just fine with the BT404 version of the touchscreen
as well. Tested on the Samsung GT-I8160 (Codina) mobile phone.
Add all the new variants from the binding document so people can
easily test them, we believe most of them work more or less.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220214234033.1052681-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Quite a few fixes here, including an unusually large set in the core
spurred on by various testing efforts as well as the usual small driver
fixes. There are quite a few fixes for out of bounds writes in both the
core and the various Qualcomm drivers, plus a couple of fixes for
locking in the DPCM code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmH5Vi4ACgkQJNaLcl1U
h9Ah6gf/SdlpKMKgAYiXAfmhb/88UgWkXWwHYgK+uHQXy3VpiG3zOso2uHQTbZ0X
+QMZ1LwPbcSsz6Ny/w/kQ4MKeklHou0X6GiQ6PRoDukBPQ6yidivwnVXt35qNBwT
iYmMuLpWsq0CrbUp9cPX+zurX+jUv/CKuwG1JnHxS2+lQ7UjetUOfKzO80X4zUA5
tm12soU9PSUcSyBICg5Jn+Tt9ZPccJ4cDPLfdRVkKjwb+6o4CnuM56Jq9UeHY6KT
SGr8/Jt0I61p8UHPUpqJsj2ItHhy80bNraSaNptQljlIYCPidgFlPKyXxgunm8e5
Z2PUG2mOIR4pk0cj1SxOXwhH9+d3dQ==
=UdmQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.17-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.17
Quite a few fixes here, including an unusually large set in the core
spurred on by various testing efforts as well as the usual small driver
fixes. There are quite a few fixes for out of bounds writes in both the
core and the various Qualcomm drivers, plus a couple of fixes for
locking in the DPCM code.
Since the commit in the Fixes tag below, 'wm->input_dev' is a managed
resource that doesn't need to be explicitly unregistered or freed (see
devm_input_allocate_device() documentation)
So, remove some unless line of code to slightly simplify it.
Fixes: c72f61e740 ("Input: wm97xx: split out touchscreen registering")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87dce7e80ea9b191843fa22415ca3aef5f3cc2e6.1643529968.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Zinitix BT532 is another touch controller that seem to implement the
same interface as an already supported BT541. Add it to the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-5-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The supply names of the Zinitix touchscreen were a bit confused, the new
bindings rectifies this.
To deal with old and new devicetrees, first check if we have "vddo" and in
case that exists assume the old supply names. Else go and look for the new
ones.
We cannot just get the regulators since we would get an OK and a dummy
regulator: we need to check explicitly for the old supply name.
Use struct device *dev as a local variable instead of the I2C client since
the device is what we are actually obtaining the resources from.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Slightly changed the legacy regulator detection]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Variable penup is assigned a value but penup is never read later, it
is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211205000525.153999-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The open delay time has to be applied only on the first sample of the
X/Y coordinates because on the following samples the ADC channel is not
changed. Removing this time from the samples after the first one,
"ti,coordinate-readouts" greater than 1, decreases the total acquisition
time, allowing to increase the number of acquired coordinates in the time
unit.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-4-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.
Fixes: 8c896308fe ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e69 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some Silead touchscreens have support for an active (battery powered)
pen, add support for this.
So far pen-support has only been seen on X86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new properties are deliberately not added
to the existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately, at the time of writing this commit message, we have been
unable to get permission from Silead, or from device OEMs, to distribute
the necessary Silead firmware files in linux-firmware.
On a whole bunch of devices the UEFI BIOS code contains a touchscreen
driver, which contains an embedded copy of the firmware. The fw-loader
code has a "platform" fallback mechanism, which together with info on the
firmware from drivers/platform/x86/touchscreen_dmi.c will use the firmware
from the UEFI driver when the firmware is missing from /lib/firmware. This
makes the touchscreen work OOTB without users needing to manually download
the firmware.
The firmware bundled with the original Windows/Android is usually newer
then the firmware in the UEFI driver and it is better calibrated. This
better calibration can lead to significant differences in the reported
min/max coordinates.
Add support for a new (optional) "silead,efi-fw-min-max" property which
provides a set of alternative min/max values to use for the x/y axis when
the EFI embedded firmware is used.
The new property is only used on (x86) devices which do not use devicetree,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added to the
existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2 small fixes for pen support
1. Set the id.vendor field for the pen input_dev
2. Fix a typo in a comment
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
goodix_get_gpio_config() errors are fatal (abort probe()) so log them
at KERN_ERR level rather then as debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.
Return instead of jumping to avoid a double free.
Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67ef ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF/AjYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hkIAJ6sFDbvb4M4LMwf
Slh2NVL9o5sLMBDzVwnVlyMSKDbMn1WBKreGssaLgZjGDc74lxsdSmw5l9MZm0JN
xlq95Q6XFiuu+0qDHPWwfDz3JFO4TqW2ZLLPWk9NnkNbRXqccSrlVRi1RpgE1t3/
NUtS8CQLu6A2BYMc6mkk3aV6IwSNKOkWbM5eBHSvU4j8B6lLbNQop0AfO/wyY1xB
U6LiVE1RpN/b7Yv+75ITtNzuHzVIBx6305FvSnOlKbMKKvIClt96Vd2OeuoEkK+6
wGU8JraB1+fc0GckAhynNrjWQWdvi0MAhFWWEJxjS20OGcV1rXDduNfkVNauO1Zn
+dNyJ3s=
=g9fz
-----END PGP SIGNATURE-----
Merge tag 'v5.15' into next
Sync up with the mainline to get the latest APIs and DT bindings.
Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a new product ID for the xpad joystick driver
- fixes to resistive-adc-touch and snvs_pwrkey drivers
- a change to touchscreen helpers to make clang happier
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: touchscreen - avoid bitwise vs logical OR warning
Input: xpad - add support for another USB ID of Nacon GC-100
Input: resistive-adc-touch - fix division by zero error on z1 == 0
Input: snvs_pwrkey - add clk handling
The ili251x firmware can be updated, this is used when switching between
different modes of operation of the touch surface, e.g. glove operation.
This patch implements the firmware update mechanism triggered by a write
into an sysfs attribute.
The firmware itself is distributed as an intel hex file with non-standard
types. The first two lines are of type 0xad, which indicates the start of
DataFlash payload, that is always at address 0xf000 on the ili251x, so it
can be dropped, and 0xac which indicates the position of firmware info in
the Application payload, that is always at address 0x2020 on the ili251x
and we do not care. The rest of the firmware is data of type 0x00, and we
care about that. To convert the firmware hex file into something usable
by the kernel, remove the first two lines and then use ihex2fw:
$ tail -n +3 input.hex > temp.hex
$ ./tools/firmware/ihex2fw temp.hex firmware/ilitek/ili251x.bin
To trigger the firmware update, place firmware file ilitek/ili251x.bin
into /lib/firmware/, write into firmware_update sysfs attribute and wait
about 30-40 seconds. The firmware update is slow. Afterward, verify the
firmware_version and mode sysfs attributes to check whether the firmware
got updated and the controller switched back to application (AP) mode by
reading out 'mode' attribute in sysfs.
Note that the content of firmware_version, e.g. 0600.0005.abcd.aa04 can
be matched to the content of the firmware hex file. The first four bytes,
0x06 0x00 0x00 0x05 can be found at ^:102030 00 05000006, the next four
bytes 0xab 0xcd 0xaa 0x04 at ^:10F000 00 nnnnnnnn ABCDAA04.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-3-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x firmware protocol permits readout of firmware version,
protocol version, mcu version and current mode (application, boot
loader, forced update). These information are useful when updating
the firmware on the il251x, e.g. to avoid updating the same firmware
into the device multiple times. The locking is now necessary to avoid
races between interrupt handler and the sysfs readouts.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-2-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x firmware protocol permits readout of panel resolution,
implement this, but make it possible to override this value using
DT bindings. This way, older DTs which contain touchscreen-size-x
and touchscreen-size-y properties will behave just like before and
new DTs may avoid specifying these for ILI251x.
Note that the command format is different on other controllers, so
this functionality is isolated to ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For proper pressure calculation we need at least x and z1 to be non
zero. Even worse, in case z1 we may run in to division by zero
error.
Fixes: 60b7db914d ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007095727.29579-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Up to now tsc200x_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211012153945.2651412-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device may take up to 100ms to become responsive during probe, so
prefer asynchronous probing to avoid delaying the rest of the system.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20211007111217.1935858-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125212.95-3-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125212.95-2-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
