commit 341fd15e2e upstream.
Commit bf7571c00d ("extcon: usbc-tusb320: Add USB TYPE-C support")
added an optional Type-C interface to the driver but missed to check
if it is in use when calling the IRQ handler. This causes an oops on
devices currently using the old extcon interface. Check if a Type-C
port is registered before calling the Type-C IRQ handler.
Fixes: bf7571c00d ("extcon: usbc-tusb320: Add USB TYPE-C support")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221107153317.657803-1-y.oudjana@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 581c848b61 ]
Currently this driver triggers extcon and typec state update in its
probe function, to read out current state reported by the chip and
report the correct state to upper layers. This synchronization is
performed correctly, but only in case the chip indicates a pending
interrupt in reg09 register.
This fails to cover the situation where all interrupts reported by
the chip were already handled by Linux before reboot, then the system
rebooted, and then Linux starts again. In this case, the TUSB320 no
longer reports any interrupts in reg09, and the state update does not
perform any update as it depends on that interrupt indication.
Fix this by turning tusb320_irq_handler() into a thin wrapper around
tusb320_state_update_handler(), where the later now contains the bulk
of the code of tusb320_irq_handler(), but adds new function parameter
"force_update". The "force_update" parameter can be used by the probe
function to assure that the state synchronization is always performed,
independent of the interrupt indicated in reg09. The interrupt handler
tusb320_irq_handler() callback uses force_update=false to avoid state
updates on potential spurious interrupts and retain current behavior.
Fixes: 06bc4ca115 ("extcon: Add driver for TI TUSB320")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221120141509.81012-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf7571c00d ]
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem,
which can expose details collected by the TUSB320 in a far more
precise way than extcon. Since there are existing users in the
kernel and in DT which depend on the extcon interface, keep it
for now.
Add TYPE-C interface and expose the supported supply current,
direction and connector polarity via the TYPE-C interface.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Stable-dep-of: 581c848b61 ("extcon: usbc-tusb320: Update state on probe even if no IRQ pending")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9483811a12 ]
Move extcon code into separate functions in preparation for addition of
USB TYPE-C support. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Stable-dep-of: 581c848b61 ("extcon: usbc-tusb320: Update state on probe even if no IRQ pending")
Signed-off-by: Sasha Levin <sashal@kernel.org>
There's no need to set the flag explicitly to false, since that
is the default value from zero initialization.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There's no need to set the flag explicitly to false, since that
is the default value from zero initialization.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
there is an unexpected word "the" in the comments that need to be dropped
file: ./drivers/extcon/extcon.c
line: 250
/* Find the the index of extcon cable in edev->supported_cable */
changed to
/* Find the index of extcon cable in edev->supported_cable */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is an extreneous space before a dev_dbg message, remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
A remove callback that just returns 0 is equivalent to no callback at all
as can be seen in i2c_device_remove(). So simplify accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently, someone can invoke the sysfs such as state_show()
intermittently before dev_set_drvdata() is done.
And it can be a cause of kernel Oops because of edev is Null at that time.
So modified the driver registration to after setting drviver data.
- Oops's backtrace.
Backtrace:
[<c067865c>] (state_show) from [<c05222e8>] (dev_attr_show)
[<c05222c0>] (dev_attr_show) from [<c02c66e0>] (sysfs_kf_seq_show)
[<c02c6648>] (sysfs_kf_seq_show) from [<c02c496c>] (kernfs_seq_show)
[<c02c4938>] (kernfs_seq_show) from [<c025e2a0>] (seq_read)
[<c025e11c>] (seq_read) from [<c02c50a0>] (kernfs_fop_read)
[<c02c5064>] (kernfs_fop_read) from [<c0231cac>] (__vfs_read)
[<c0231c5c>] (__vfs_read) from [<c0231ee0>] (vfs_read)
[<c0231e34>] (vfs_read) from [<c0232464>] (ksys_read)
[<c02323f0>] (ksys_read) from [<c02324fc>] (sys_read)
[<c02324e4>] (sys_read) from [<c00091d0>] (__sys_trace_return)
Signed-off-by: bumwoo lee <bw365.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
While SM5502 and SM5504 are purely micro USB switching
circuits, SM5703 is a multi-function device which has multiple
modules in it. Change the i2c_device_id of it to avoid conflict
with MFD driver.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some usb controller drivers may not support extcon but use
usb role class as it's the preferred approach, so to support
usb dual role switch with usb role class, add usb role class
consumer support.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add device managed action to sync pending queue work, otherwise
the queued work may run after the work is destroyed.
Fixes: 4ed754de2d ("extcon: Add support for ptn5150 extcon driver")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
SM5703 is another MFD from Silicon Mitus which has a very similar MUIC
unit to the one in SM5502. The only difference I've noticed is slightly different
configuration only enables the interrupts which are exactly the same as on SM5502.
If we make use of different interrupts in the future, this can be improved by having
a separate struct for SM5703, but the main functionality (detecting cable or OTG adapter)
is working properly.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If disable vbus/id irq, it will lead to wakeup system fail
in unisoc platform. In unisoc platform, Irq enable and irq
wakeup are the same interrupt line. So remove disable vbus/id
irq operation is a way to solve the issue.
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add the description of @id in extcon_sync() kernel-doc comment
and @edev, @id, @prop in extcon_set_property_sync() kernel-doc
comment to remove warnings found by running scripts/kernel-doc,
which is caused by using 'make W=1'.
drivers/extcon/extcon.c:409: warning: Function parameter or
member 'id' not described in 'extcon_sync'
drivers/extcon/extcon.c:750: warning: Function parameter or
member 'edev' not described in 'extcon_set_property_sync'
drivers/extcon/extcon.c:750: warning: Function parameter or
member 'id' not described in 'extcon_set_property_sync'
drivers/extcon/extcon.c:750: warning: Function parameter or
member 'prop' not described in 'extcon_set_property_sync'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On some boards the 5V vboost-regulator for powering devices connected to
the micro USB connector is not controlled through a GPIO. This happens
for example when the 5V vboost-regulator is integrated into the charger IC
and controlled over I2C.
Add support for controlling the 5V vboost-regulator through the regulator
framework for such boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On some X86 Android tablets the DSTD lack the INT3496 ACPI device,
while also not handling micro USB port ID pin events inside the DSDT
(instead the forked factory image kernel has things hardcoded).
The new drivers/platform/x86/x86-android-tablets.c module manually
instantiates an intel-int3496 device for these tablets.
Add support to the extcon-intel-int3496 driver to bind to devices
without an ACPI companion and export a normal platform_device
modalias for automatic module loading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some DSDTs are buggy and do a read from the ID pin during the ACPI
initialization, causing the pin to be marked as owned by:
"ACPI:OpRegion" and causing gpiod_get() to fail with -EBUSY.
Pass the GPIOD_FLAGS_BIT_NONEXCLUSIVE flag to the gpiod_get() call
to work around this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On all devices which I have with an INT3496 ACPI device,
there is only an ID pin defined.
Change the log-messages about not being able to get GPIOs for
"VBUS EN" and "USB MUX" to use dev_dbg().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Make cht_wc_extcon_get_id() report RID_A for ACA adapters, instead of
reporting ID_FLOAT.
According to the spec. we should read the USB-ID pin ADC value
to determine the resistance of the used pull-down resister and
then return RID_A / RID_B / RID_C based on this. But all "Accessory
Charger Adapter"s (ACAs) which users can actually buy always use
a combination of a charging port with one or more USB-A ports, so
they should always use a resistor indicating RID_A. But the spec
is hard to read / badly-worded so some of them actually indicate
they are a RID_B ACA even though they clearly are a RID_A ACA.
To workaround this simply always return INTEL_USB_RID_A, which
matches all the ACAs which users can actually buy.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25890 used on the Yogabook YB1-X90 / -X91 models relies on
the extcon-driver's BC-1.2 charger detection, and the bq25890 driver
expect this info to be available through a parent power_supply
class-device which models the detected charger (idem to how the Type-C
TCPM code registers a power_supply classdev for the connected charger).
Add support for registering the power_supply class-device expected
by this setup.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This is a preparation patch for adding support for registering
a power_supply class device.
Setting usbsrc to "CHT_WC_USBSRC_TYPE_SDP << CHT_WC_USBSRC_TYPE_SHIFT"
will make the following switch-case return EXTCON_CHG_USB_SDP
just as before, so there is no functional change.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
So far the extcon-intel-cht-wc code has only been tested on devices with
a Type-C connector with USB-PD, USB3 (superspeed) and DP-altmode support
through a FUSB302 Type-C controller.
Some devices with the intel-cht-wc PMIC however come with an USB-micro-B
connector, or an USB-2 only Type-C connector without USB-PD.
Which device-model we are running on can be identified with the new
cht_wc_model intel_soc_pmic field. On models without a Type-C controller
the extcon code must control the Vbus 5V boost converter and the USB role
switch depending on the detected cable-type.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The CHT_WC_VBUS_GPIO_CTLO GPIO actually driving an external 5V Vboost
converter for Vbus depends on the board on which the Cherry Trail -
Whiskey Cove PMIC is actually used.
Since the information about the exact PMIC setup is necessary in other
places too, struct intel_soc_pmic now has a new cht_wc_model field
indicating the board model.
Only poke the CHT_WC_VBUS_GPIO_CTLO GPIO if this new field is set to
INTEL_CHT_WC_GPD_WIN_POCKET, which indicates the Type-C (with PD and
DP-altmode) setup used on the GPD pocket and GPD win; and on which
this GPIO actually controls an external 5V Vboost converter.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Finding the cable index and checking for changed status is also done
in extcon_set_state(). So calling extcon_set_state_sync() will do these
checks twice. Remove them and use these checks from extcon_set_state().
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Do not use "/**" to begin a non-kernel-doc comment.
Fixes this build warning:
drivers/extcon/extcon-usb-gpio.c:23:
warning: expecting prototype for drivers/extcon/extcon-usb-gpio.c().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
TUSB320L is a newer chip with additional features, and it has additional steps
in its mode changing sequence:
- Disable CC state machine,
- Write to mode register,
- Wait for 5 ms,
- Re-enable CC state machine.
It also has an additional register that a revision number can be read from.
Add support for the mode changing sequence, and read the revision number during
probe and print it as info.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reset the chip and set its mode to default (maintain mode set by PORT pin)
during probe to make sure it comes up in the default state.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
use low level P-Unit semaphore lock for axp288 register
accesses directly and for more than one access a time,
to reduce the number of times this semaphore is locked
and released which is an expensive operation.
i2c-bus to the XPower is shared between the kernel and the
SoCs P-Unit. The P-Unit has a semaphore wich the kernel must
lock for axp288 register accesses. When the P-Unit semaphore
is locked CPU and GPU power states cannot change or the system
will freeze.
The P-Unit semaphore lock is already managed inside the regmap
access logic, but for each access the semaphore is locked and
released. So use directly iosf_mbi_(un)block_punit_i2c_access(),
we are safe in doing so because nested calls to the same
semaphore are turned to nops.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This driver includes the legacy <linux/gpio.h> header but
does not use it. Drop this include.
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The USB GPIO extcon driver does not use any of the legacy
includes <linux/gpio.h> or <linux/of_gpio.h> but
exploits the fact that this brings in <linux/mod_device_table.h>.
Fix this up by using the right includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
SM5504 is another MUIC from Silicon Mitus that is fairly similar
to SM5502. They seem to use the same register set, but:
- SM5504 has some additional bits in SM5502_REG_CONTROL
- SM5504 has a quite different set of interrupts
- SM5504 reports USB OTG as dev_type1 = BIT(0) instead of BIT(7)
Overall it's minor and we can support this by defining a separate
struct sm5502_type for SM5504.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Prepare for supporting SM5504 in the extcon-sm5502 driver by replacing
enum sm5504_types with a struct sm5504_type that stores the chip-specific
definitions. This struct can then be defined separately for SM5504
without having to add if (type == TYPE_SM5504) everywhere in the code.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
sm5022_muic_i2c_probe() does not use the i2c_device_id,
so implement i2c_driver->probe_new() instead of probe().
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Use devm_regmap_add_irq_chip() to avoid having to remove the
irqchip explicitly in sm5502_muic_i2c_remove().
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The platform device driver name is "max8997-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: b76668ba8a ("Extcon: add MAX8997 extcon driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When sm5502_init_dev_type() iterates over sm5502_reg_data to
initialize the registers it is limited by ARRAY_SIZE(sm5502_reg_data).
There is no need to add another empty element to sm5502_reg_data.
Having the additional empty element in sm5502_reg_data will just
result in writing 0xff to register 0x00, which does not really
make sense.
Fixes: 914b881f94 ("extcon: sm5502: Add support new SM5502 extcon device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon driver for Basin Cove PMIC shadows the switch status used for dwc3
DRD to detect a change in the switch position. This change initializes the
status at probe time.
Cc: stable@vger.kernel.org
Fixes: 492929c547 ("extcon: mrfld: Introduce extcon driver for Basin Cove PMIC")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If reading MAX8997_MUIC_REG_STATUS1 fails at probe the driver exits
without freeing the requested IRQs.
Free the IRQs prior returning if reading the status fails.
Fixes: 3e34c81989 ("extcon: max8997: Avoid forcing UART path on drive probe")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/27ee4a48ee775c3f8c9d90459c18b6f2b15edc76.1623146580.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The extcon IRQ schedules a work item. IRQ is requested using devm while
WQ is cancelld at remove(). This mixing of devm and manual unwinding has
potential case where the WQ has been emptied (.remove() was ran) but
devm unwinding of IRQ was not yet done. It may be possible the IRQ is
triggered at this point scheduling new work item to the already flushed
queue.
According to the input documentation the input device allocated by
devm_input_allocate_device() does not need to be explicitly unregistered.
Use the new devm_work_autocancel() and remove the remove() to simplify the
code.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/cbe8205eed8276f6e6db5003cfe51b8b0d4ac966.1623146580.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The extcon IRQ schedules a work item. IRQ is requested using devm while
WQ is cancelld at remove(). This mixing of devm and manual unwinding has
potential case where the WQ has been emptied (.remove() was ran) but
devm unwinding of IRQ was not yet done. It is possible the IRQ is triggered
at this point scheduling new work item to the already flushed queue.
Use new devm_work_autocancel() to remove the remove() and to kill the bug.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/ee8545f59ae3a93f0a70f640ecbd7e31cfadbcb9.1623146580.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
- New Drivers
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
- New Device Support
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
- Removed Device Support
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
- New Functionality
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
- New/converted Device Tree bindings; rohm,bd71815-pmic, rohm,bd9576-pmic,
netronix,ntxec, actions,atc260x,
ricoh,rn5t618, qcom-pm8xxx
- Fix-ups
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618, max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci,
atc260x-i2c, intel_quark_i2c_gpio
- Bug Fixes
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers
-----BEGIN PGP SIGNATURE-----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=IJSL
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
Here is the "big" set of driver core changes for 5.13-rc1.
Nothing major, just lots of little core changes and cleanups, notable
things are:
- finally set fw_devlink=on by default. All reported issues
with this have been shaken out over the past 9 months or so,
but we will be paying attention to any fallout here in case we
need to revert this as the default boot value (symptoms of
problems are a simple lack of booting)
- fixes found to be needed by fw_devlink=on value in some
subsystems (like clock).
- delayed work initialization cleanup
- driver core cleanups and minor updates
- software node cleanups and tweaks
- devtmpfs cleanups
- minor debugfs cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIazPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylzUwCguQ+VUs1d0voq/oKiqR+lbXnQf3kAn0jf/eom
ucRSdeIc21eEE83Ei9aZ
=pchl
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core changes for 5.13-rc1.
Nothing major, just lots of little core changes and cleanups, notable
things are:
- finally set 'fw_devlink=on' by default.
All reported issues with this have been shaken out over the past 9
months or so, but we will be paying attention to any fallout here
in case we need to revert this as the default boot value (symptoms
of problems are a simple lack of booting)
- fixes found to be needed by fw_devlink=on value in some subsystems
(like clock).
- delayed work initialization cleanup
- driver core cleanups and minor updates
- software node cleanups and tweaks
- devtmpfs cleanups
- minor debugfs cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (53 commits)
devm-helpers: Fix devm_delayed_work_autocancel() kerneldoc
PM / wakeup: use dev_set_name() directly
software node: Allow node addition to already existing device
kunit: software node: adhear to KUNIT formatting standard
node: fix device cleanups in error handling code
kobject_uevent: remove warning in init_uevent_argv()
debugfs: Make debugfs_allow RO after init
Revert "driver core: platform: Make platform_get_irq_optional() optional"
media: ipu3-cio2: Switch to use SOFTWARE_NODE_REFERENCE()
software node: Introduce SOFTWARE_NODE_REFERENCE() helper macro
software node: Imply kobj_to_swnode() to be no-op
software node: Deduplicate code in fwnode_create_software_node()
software node: Introduce software_node_alloc()/software_node_free()
software node: Free resources explicitly when swnode_register() fails
debugfs: drop pointless nul-termination in debugfs_read_file_bool()
driver core: add helper for deferred probe reason setting
driver core: Improve fw_devlink & deferred_probe_timeout interaction
of: property: fw_devlink: Add support for remote-endpoint
driver core: platform: Make platform_get_irq_optional() optional
driver core: Replace printf() specifier and drop unneeded casting
...
VBUS can be detected via a dedicated PMIC pin. Add support
for reporting the VBUS status.
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Kavya Nunna <knunna@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Yassine Oudjana