The drivers has been moved out since
0097e20e77 ("staging:iio:adc:lpc32xx Move out of staging.") in v4.10,
so let's align the binding documentation.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
commit f836c45922 moved mxs-lradc driver
out of staging. However the binding document was left in the old place.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
At the beginning the driver supported only i.MX28 SoC, but now the
whole MXS platform. So remove any confusing comments which apply
only to i.MX28.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes off-by-one issues in the devicetree binding of
mxs-lradc.
According to the i.MX23 and i.MX28 reference manuals [1][2] the range of
NUM_SAMPLES is 0..31, but property ave-ctrl is substracted by 1 before used.
Considering all limitations the range of DELAY is 1..2047, but also
property ave-delay is substracted by 1 before used.
The patch has been suggested by Hartmut Knaack and Kristina Martsenko.
[1] - http://cache.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf
[2] - http://cache.freescale.com/files/dsp/doc/ref_manual/MCIMX28RM.pdf
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is an RFC for the new touchscreen properties.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-input@vger.kernel.org
CC: devel@driverdev.osuosl.org
CC: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: devicetree@vger.kernel.org
This patch implements support for sampling of a touchscreen into
the MXS LRADC driver. The LRADC block allows configuring some of
it's channels into special mode where they either output the drive
voltage or sample it, allowing it to operate a 4-wire or 5-wire
resistive touchscreen.
In case the touchscreen mode is enabled, the LRADC slot #7 is
reserved for touchscreen only, therefore it is not possible to
sample 8 LRADC channels at time, but only 7 channels.
The touchscreen controller is configured such that the PENDOWN event
disables touchscreen interrupts and triggers execution of worker
thread, which then polls the touchscreen controller for X, Y and
Pressure values. This reduces the overhead of interrupt-driven
operation. Upon the PENUP event, the worker thread re-enables the
PENDOWN detection interrupt and exits.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver is very basic. It supports userland trigger, buffer and
raw access to channels. The support for delay channels is missing
altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Juergen Beisert <jbe@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfgang Denk <wd@denx.de>
This patch adds device tree support to the LPC32xx's ADC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements the basic single data conversion support for
the SPEAr600 SoC ADC. The register layout of SPEAr600 differs a bit
from other SPEAr SoC variants (e.g. SPEAr3xx). These differences are
handled via DT compatible testing. Resulting in a multi-arch binary.
This driver is currently tested only on SPEAr600. Future patches may add
support for other SoC variants (SPEAr3xx) and features like software
buffer or DMA.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
