When sending HCI_OP_CREATE_CONN_CANCEL it shall Wait for
HCI_EV_CONN_COMPLETE, not HCI_EV_CMD_STATUS, when the reason is
anything but HCI_ERROR_REMOTE_POWER_OFF. This reason is used when
suspending or powering off, where we don't want to wait for the peer's
response.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Dropped CIS that are in state BT_OPEN/BT_BOUND, and in state BT_CONNECT
with HCI_CONN_CREATE_CIS unset, should be cleaned up immediately.
Closing CIS ISO sockets should result to the hci_conn be deleted, so
that potentially pending CIG removal can run.
hci_abort_conn cannot refer to them by handle, since their handle is
still unset if Set CIG Parameters has not yet completed.
This fixes CIS not being terminated if the socket is shut down
immediately after connection, so that the hci_abort_conn runs before Set
CIG Parameters completes. See new BlueZ test "ISO Connect Close - Success"
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some use cases require the user to be informed if BIG synchronization
fails. This commit makes it so that even if the BIG sync established
event arrives with error status, a new hconn is added for each BIS,
and the iso layer is notified about the failed connections.
Unsuccesful bis connections will be marked using the
HCI_CONN_BIG_SYNC_FAILED flag. From the iso layer, the POLLERR event
is triggered on the newly allocated bis sockets, before adding them
to the accept list of the parent socket.
From user space, a new fd for each failed bis connection will be
obtained by calling accept. The user should check for the POLLERR
event on the new socket, to determine if the connection was successful
or not.
The HCI_CONN_BIG_SYNC flag has been added to mark whether the BIG sync
has been successfully established. This flag is checked at bis cleanup,
so the HCI LE BIG Terminate Sync command is only issued if needed.
The BT_SK_BIG_SYNC flag indicates if BIG create sync has been called
for a listening socket, to avoid issuing the command everytime a BIGInfo
advertising report is received.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
ISO_LINK connections where not being handled properly on
hci_abort_conn_sync which sometimes resulted in sending the wrong
commands, or in case of having the reject command being sent by the
socket code (iso.c) which is sort of a layer violation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This consolidates code for aborting connections using
hci_cmd_sync_queue so it is synchronized with other threads, but
because of the fact that some commands may block the cmd_sync_queue
while waiting specific events this attempt to cancel those requests by
using hci_cmd_sync_cancel.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In the case of a Synchronized Receiver capable device, enable at start-up the
events for PA reports, PA Sync Established and Big Info Adv reports.
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for creating multiple BIGs. According to
spec, each BIG shall have an unique handle, and each BIG should
be associated with a different advertising handle. Otherwise,
the LE Create BIG command will fail, with error code
Command Disallowed (for reusing a BIG handle), or
Unknown Advertising Identifier (for reusing an advertising
handle).
The btmon snippet below shows an exercise for creating two BIGs
for the same controller, by opening two isotest instances with
the following command:
tools/isotest -i hci0 -s 00:00:00:00:00:00
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31
Handle: 0x00
Advertising Handle: 0x01
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 21
LE Broadcast Isochronous Group Complete (0x1b)
Status: Success (0x00)
Handle: 0x00
BIG Synchronization Delay: 912 us (0x000390)
Transport Latency: 912 us (0x000390)
PHY: LE 2M (0x02)
NSE: 3
BN: 1
PTO: 1
IRC: 3
Maximum PDU: 40
ISO Interval: 10.00 msec (0x0008)
Connection Handle #0: 10
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068)
Handle: 0x01
Advertising Handle: 0x02
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
LE Create CIS command shall not be sent before all CIS Established
events from its previous invocation have been processed. Currently it is
sent via hci_sync but that only waits for the first event, but there can
be multiple.
Make it wait for all events, and simplify the CIS creation as follows:
Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been
sent for the connection but it is not yet completed.
Make BT_CONNECT state to mean the connection wants Create CIS.
On events after which new Create CIS may need to be sent, send it if
possible and some connections need it. These events are:
hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis,
hci_le_cis_estabilished_evt.
The Create CIS status/completion events shall queue new Create CIS only
if at least one of the connections transitions away from BT_CONNECT, so
that we don't loop if controller is sending bogus events.
This fixes sending multiple CIS Create for the same CIS in the
"ISO AC 6(i) - Success" BlueZ test case:
< HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0]
Number of CIS: 2
CIS Handle: 257
ACL Handle: 42
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #130 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 257
...
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0]
...
> HCI Event: Command Complete (0x0e) plen 6 #133 [hci0]
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
...
< HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0]
Number of CIS: 1
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #135 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: ACL Connection Already Exists (0x0b)
> HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 258
...
Fixes: c09b80be6f ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_update_accept_list_sync iterates over hdev->pend_le_conns and
hdev->pend_le_reports, and waits for controller events in the loop body,
without holding hdev lock.
Meanwhile, these lists and the items may be modified e.g. by
le_scan_cleanup. This can invalidate the list cursor or any other item
in the list, resulting to invalid behavior (eg use-after-free).
Use RCU for the hci_conn_params action lists. Since the loop bodies in
hci_sync block and we cannot use RCU or hdev->lock for the whole loop,
copy list items first and then iterate on the copy. Only the flags field
is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we
read valid values.
Free params everywhere with hci_conn_params_free so the cleanup is
guaranteed to be done properly.
This fixes the following, which can be triggered e.g. by BlueZ new
mgmt-tester case "Add + Remove Device Nowait - Success", or by changing
hci_le_set_cig_params to always return false, and running iso-tester:
==================================================================
BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107)
print_report (mm/kasan/report.c:320 mm/kasan/report.c:430)
? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65)
? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
kasan_report (mm/kasan/report.c:538)
? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841)
? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780)
? mutex_lock (kernel/locking/mutex.c:282)
? __pfx_mutex_lock (kernel/locking/mutex.c:282)
? __pfx_mutex_unlock (kernel/locking/mutex.c:538)
? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861)
hci_cmd_sync_work (net/bluetooth/hci_sync.c:306)
process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538)
? __pfx_worker_thread (kernel/workqueue.c:2480)
kthread (kernel/kthread.c:376)
? __pfx_kthread (kernel/kthread.c:331)
ret_from_fork (arch/x86/entry/entry_64.S:314)
</TASK>
Allocated by task 31:
kasan_save_stack (mm/kasan/common.c:46)
kasan_set_track (mm/kasan/common.c:52)
__kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383)
hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277)
hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589)
hci_connect_cis (net/bluetooth/hci_conn.c:2266)
iso_connect_cis (net/bluetooth/iso.c:390)
iso_sock_connect (net/bluetooth/iso.c:899)
__sys_connect (net/socket.c:2003 net/socket.c:2020)
__x64_sys_connect (net/socket.c:2027)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
Freed by task 15:
kasan_save_stack (mm/kasan/common.c:46)
kasan_set_track (mm/kasan/common.c:52)
kasan_save_free_info (mm/kasan/generic.c:523)
__kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244)
__kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800)
hci_conn_params_del (net/bluetooth/hci_core.c:2323)
le_scan_cleanup (net/bluetooth/hci_conn.c:202)
process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538)
kthread (kernel/kthread.c:376)
ret_from_fork (arch/x86/entry/entry_64.S:314)
==================================================================
Fixes: e8907f7654 ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Devices that lack persistent storage for the device address can indicate
this by setting the HCI_QUIRK_INVALID_BDADDR which causes the controller
to be marked as unconfigured until user space has set a valid address.
The related HCI_QUIRK_USE_BDADDR_PROPERTY was later added to similarly
indicate that the device lacks a valid address but that one may be
specified in the devicetree.
As is clear from commit 7a0e5b15ca ("Bluetooth: Add quirk for reading
BD_ADDR from fwnode property") that added and documented this quirk and
commits like de79a9df16 ("Bluetooth: btqcomsmd: use
HCI_QUIRK_USE_BDADDR_PROPERTY"), the device address of controllers with
this flag should be treated as invalid until user space has had a chance
to configure the controller in case the devicetree property is missing.
As it does not make sense to allow controllers with invalid addresses,
restore the original semantics, which also makes sure that the
implementation is consistent (e.g. get_missing_options() indicates that
the address must be set) and matches the documentation (including
comments in the code, such as, "In case any of them is set, the
controller has to start up as unconfigured.").
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devices that lack persistent storage for the device address can indicate
this by setting the HCI_QUIRK_INVALID_BDADDR which causes the controller
to be marked as unconfigured until user space has set a valid address.
Once configured, the device address must be set on every setup for
controllers with HCI_QUIRK_NON_PERSISTENT_SETUP to avoid marking the
controller as unconfigured and requiring the address to be set again.
Fixes: 740011cfe9 ("Bluetooth: Add new quirk for non-persistent setup settings")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit ec6cef9cd9 ("Bluetooth: Fix SMP channel registration for
unconfigured controllers") the debugfs interface for unconfigured
controllers will be created when the controller is configured.
There is however currently nothing preventing a controller from being
configured multiple time (e.g. setting the device address using btmgmt)
which results in failed attempts to register the already registered
debugfs entries:
debugfs: File 'features' in directory 'hci0' already present!
debugfs: File 'manufacturer' in directory 'hci0' already present!
debugfs: File 'hci_version' in directory 'hci0' already present!
...
debugfs: File 'quirk_simultaneous_discovery' in directory 'hci0' already present!
Add a controller flag to avoid trying to register the debugfs interface
more than once.
Fixes: ec6cef9cd9 ("Bluetooth: Fix SMP channel registration for unconfigured controllers")
Cc: stable@vger.kernel.org # 4.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When the HCI_UNREGISTER flag is set, no jobs should be scheduled. Fix
potential race when HCI_UNREGISTER is set after the flag is tested in
hci_cmd_sync_queue.
Fixes: 0b94f2651f ("Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes sure hci_cmd_sync_queue only queue new work if HCI_RUNNING
has been set otherwise there is a risk of commands being sent while
turning off.
Because hci_cmd_sync_queue can no longer queue work while HCI_RUNNING is
not set it cannot be used to power on adapters so instead
hci_cmd_sync_submit is introduced which bypass the HCI_RUNNING check, so
it behaves like the old implementation.
Link: https://lore.kernel.org/all/CAB4PzUpDMvdc8j2MdeSAy1KkAE-D3woprCwAdYWeOc-3v3c9Sw@mail.gmail.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.
Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.
< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When submitting HCI_OP_LE_CREATE_CIS the code shall wait for
HCI_EVT_LE_CIS_ESTABLISHED thus enforcing the serialization of
HCI_OP_LE_CREATE_CIS as the Core spec does not allow to send them in
parallel:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E page 2566:
If the Host issues this command before all the HCI_LE_CIS_Established
events from the previous use of the command have been generated, the
Controller shall return the error code Command Disallowed (0x0C).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables 2M and Coded PHY by default if they are marked as supported
in the LE features bits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add devcoredump APIs to hci core so that drivers only have to provide
the dump skbs instead of managing the synchronization and timeouts.
The devcoredump APIs should be used in the following manner:
- hci_devcoredump_init is called to allocate the dump.
- hci_devcoredump_append is called to append any skbs with dump data
OR hci_devcoredump_append_pattern is called to insert a pattern.
- hci_devcoredump_complete is called when all dump packets have been
sent OR hci_devcoredump_abort is called to indicate an error and
cancel an ongoing dump collection.
The high level APIs just prepare some skbs with the appropriate data and
queue it for the dump to process. Packets part of the crashdump can be
intercepted in the driver in interrupt context and forwarded directly to
the devcoredump APIs.
Internally, there are 5 states for the dump: idle, active, complete,
abort and timeout. A devcoredump will only be in active state after it
has been initialized. Once active, it accepts data to be appended,
patterns to be inserted (i.e. memset) and a completion event or an abort
event to generate a devcoredump. The timeout is initialized at the same
time the dump is initialized (defaulting to 10s) and will be cleared
either when the timeout occurs or the dump is complete or aborted.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the following duplicate statement in
hci_le_ext_directed_advertising_sync():
cp.own_addr_type = own_addr_type;
Signed-off-by: Inga Stotland <inga.stotland@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently, when we initiate disconnection, we will wait for the peer's
reply unless when we are suspending, where we fire and forget the
disconnect request.
A similar case is when adapter is powering off. However, we still wait
for the peer's reply in this case. Therefore, if the peer is
unresponsive, the command will time out and the power off sequence
will fail, causing "bluetooth powered on by itself" to users.
This patch makes the host doesn't wait for the peer's reply when the
disconnection reason is powering off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following new warning:
net/bluetooth/hci_sync.c:2403 hci_pause_addr_resolution() warn: missing
error code? 'err'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202302251952.xryXOegd-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes errors like bellow when LE Connection times out since that
is actually not a controller error:
Bluetooth: hci0: Opcode 0x200d failed: -110
Bluetooth: hci0: request failed to create LE connection: err -110
Instead the code shall properly detect if -ETIMEDOUT is returned and
send HCI_OP_LE_CREATE_CONN_CANCEL to give up on the connection.
Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60 ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There is a potential race condition in hci_cmd_sync_work and
hci_cmd_sync_clear, and could lead to use-after-free. For instance,
hci_cmd_sync_work is added to the 'req_workqueue' after cancel_work_sync
The entry of 'cmd_sync_work_list' may be freed in hci_cmd_sync_clear, and
causing kernel panic when it is used in 'hci_cmd_sync_work'.
Here's the call trace:
dump_stack_lvl+0x49/0x63
print_report.cold+0x5e/0x5d3
? hci_cmd_sync_work+0x282/0x320
kasan_report+0xaa/0x120
? hci_cmd_sync_work+0x282/0x320
__asan_report_load8_noabort+0x14/0x20
hci_cmd_sync_work+0x282/0x320
process_one_work+0x77b/0x11c0
? _raw_spin_lock_irq+0x8e/0xf0
worker_thread+0x544/0x1180
? poll_idle+0x1e0/0x1e0
kthread+0x285/0x320
? process_one_work+0x11c0/0x11c0
? kthread_complete_and_exit+0x30/0x30
ret_from_fork+0x22/0x30
</TASK>
Allocated by task 266:
kasan_save_stack+0x26/0x50
__kasan_kmalloc+0xae/0xe0
kmem_cache_alloc_trace+0x191/0x350
hci_cmd_sync_queue+0x97/0x2b0
hci_update_passive_scan+0x176/0x1d0
le_conn_complete_evt+0x1b5/0x1a00
hci_le_conn_complete_evt+0x234/0x340
hci_le_meta_evt+0x231/0x4e0
hci_event_packet+0x4c5/0xf00
hci_rx_work+0x37d/0x880
process_one_work+0x77b/0x11c0
worker_thread+0x544/0x1180
kthread+0x285/0x320
ret_from_fork+0x22/0x30
Freed by task 269:
kasan_save_stack+0x26/0x50
kasan_set_track+0x25/0x40
kasan_set_free_info+0x24/0x40
____kasan_slab_free+0x176/0x1c0
__kasan_slab_free+0x12/0x20
slab_free_freelist_hook+0x95/0x1a0
kfree+0xba/0x2f0
hci_cmd_sync_clear+0x14c/0x210
hci_unregister_dev+0xff/0x440
vhci_release+0x7b/0xf0
__fput+0x1f3/0x970
____fput+0xe/0x20
task_work_run+0xd4/0x160
do_exit+0x8b0/0x22a0
do_group_exit+0xba/0x2a0
get_signal+0x1e4a/0x25b0
arch_do_signal_or_restart+0x93/0x1f80
exit_to_user_mode_prepare+0xf5/0x1a0
syscall_exit_to_user_mode+0x26/0x50
ret_from_fork+0x15/0x30
Fixes: 6a98e3836f ("Bluetooth: Add helper for serialized HCI command execution")
Cc: stable@vger.kernel.org
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The address resolution should be disabled during the active scan,
so all the advertisements can reach the host. The advertising
has to be paused before disabling the address resolution,
because the advertising will prevent any changes to the resolving
list and the address resolution status. Skipping this will cause
the hci error and the discovery failure.
According to the bluetooth specification:
"7.8.44 LE Set Address Resolution Enable command
This command shall not be used when:
- Advertising (other than periodic advertising) is enabled,
- Scanning is enabled, or
- an HCI_LE_Create_Connection, HCI_LE_Extended_Create_Connection, or
HCI_LE_Periodic_Advertising_Create_Sync command is outstanding."
If the host is using RPA, the controller needs to generate RPA for
the advertising, so the advertising must remain paused during the
active scan.
If the host is not using RPA, the advertising can be resumed after
disabling the address resolution.
Fixes: 9afc675ede ("Bluetooth: hci_sync: allow advertise when scan without RPA")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When hci_cmd_sync_queue() failed in hci_update_adv_data(), inst_ptr is
not freed, which will cause memory leak, convert to use ERR_PTR/PTR_ERR
to pass the instance to callback so no memory needs to be allocated.
Fixes: 651cd3d65b ("Bluetooth: convert hci_update_adv_data to hci_sync")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Don't try to use HCI_OP_LE_READ_BUFFER_SIZE_V2 if controller don't
support ISO channels, but in order to check if ISO channels are
supported HCI_OP_LE_READ_LOCAL_FEATURES needs to be done earlier so the
features bits can be checked on hci_le_read_buffer_size_sync.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216817
Fixes: c1631dbc00 ("Bluetooth: hci_sync: Fix hci_read_buffer_size_sync")
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If a command is already sent, we take care of freeing it, but we
also need to cancel the timeout as well.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This attempts to program the address stored in hdev->static_addr after
the init sequence has been complete:
@ MGMT Command: Set Static A.. (0x002b) plen 6
Address: C0:55:44:33:22:11 (Static)
@ MGMT Event: Command Complete (0x0001) plen 7
Set Static Address (0x002b) plen 4
Status: Success (0x00)
Current settings: 0x00008200
Low Energy
Static Address
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00008200
Low Energy
Static Address
< HCI Command: LE Set Random.. (0x08|0x0005) plen 6
Address: C0:55:44:33:22:11 (Static)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 7
Set Powered (0x0005) plen 4
Status: Success (0x00)
Current settings: 0x00008201
Powered
Low Energy
Static Address
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00008201
Powered
Low Energy
Static Address
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Brian Gix <brian.gix@intel.com>
Handling of Read Local Supported Codecs was broken during the
HCI serialization design change patches.
Fixes: d0b137062b ("Bluetooth: hci_sync: Rework init stages")
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A patch series by a Qualcomm engineer essentially removed my
quirk/workaround because they thought it was unnecessary.
It wasn't, and it broke everything again:
https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=*
He argues that the quirk is not necessary because the code should check
if the dongle says if it's supported or not. The problem is that for
these Chinese CSR clones they say that it would work:
= New Index: 00:00:00:00:00:00 (Primary,USB,hci0)
= Open Index: 00:00:00:00:00:00
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
> [hci0] 11.276039
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810)
LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312)
Manufacturer: Cambridge Silicon Radio (10)
...
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 68
> [hci0] 11.668030
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 163 entries
...
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
...
...
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
= Close Index: 00:1A:7D:DA:71:XX
So bring it back wholesale.
Fixes: 63b1a7dd38 ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING")
Fixes: e168f69008 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR")
Fixes: 766ae2422b ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk")
Cc: stable@vger.kernel.org
Cc: Zijun Hu <quic_zijuhu@quicinc.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When setting power state using legacy/non-mgmt API
(e.g hcitool hci0 up) the likes of mgmt_set_powered_complete won't be
called causing clients of the MGMT API to not be notified of the change
of the state.
Fixes: cf75ad8b41 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Some drivers depend on shutdown being called for proper operation.
Unset HCI_USER_CHANNEL and call the full close routine since shutdown is
complementary to setup.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Address resolution will be paused during active scan to allow any
advertising reports reach the host. If LL privacy is enabled,
advertising will rely on the controller to generate new RPA.
If host is not using RPA, there is no need to stop advertising during
active scan because there is no need to generate RPA in the controller.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_read_buffer_size_sync shall not use HCI_OP_LE_READ_BUFFER_SIZE_V2
sinze that is LE specific, instead it is hci_le_read_buffer_size_sync
version that shall use it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216382
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The patch adds state bits, storage and HCI command chains for sending
and receiving Bluetooth Mesh advertising packets, and delivery to
requesting user space processes. It specifically creates 4 new MGMT
commands and 2 new MGMT events:
MGMT_OP_SET_MESH_RECEIVER - Sets passive scan parameters and a list of
AD Types which will trigger Mesh Packet Received events
MGMT_OP_MESH_READ_FEATURES - Returns information on how many outbound
Mesh packets can be simultaneously queued, and what the currently queued
handles are.
MGMT_OP_MESH_SEND - Command to queue a specific outbound Mesh packet,
with the number of times it should be sent, and the BD Addr to use.
Discrete advertisments are added to the ADV Instance list.
MGMT_OP_MESH_SEND_CANCEL - Command to cancel a prior outbound message
request.
MGMT_EV_MESH_DEVICE_FOUND - Event to deliver entire received Mesh
Advertisement packet, along with timing information.
MGMT_EV_MESH_PACKET_CMPLT - Event to indicate that an outbound packet is
no longer queued for delivery.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When disconnecting all devices, hci_conn_failed is used to cleanup
hci_conn object when the hci_conn object cannot be aborted.
The function hci_conn_failed requires the caller holds hdev->lock.
Fixes: 9b3628d79b ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This attempts to fix suspend performance when there is no connections by
not updating the event mask.
Fixes: ef61b6ea15 ("Bluetooth: Always set event mask on suspend")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_update_adv_data() is called from hci_event and hci_core due to
events from the controller. The prior function used the deprecated
hci_request method, and the new one uses hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This function has no dependencies on the deprecated hci_request
mechanism, so has been moved unchanged to hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Advertising Instance expiration timer adv_instance_expire was
handled with the deprecated hci_request mechanism, rather than it's
replacement: hci_sync.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
le_scan_restart delayed work queue was running as a deprecated
hci_request instead of on the newer thread-safe hci_sync mechanism.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The le_scan_disable timeout was being performed on the deprecated
hci_request.c mechanism. This timeout is performed in hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When suspending, always set the event mask once disconnects are
successful. Otherwise, if wakeup is disallowed, the event mask is not
set before suspend continues and can result in an early wakeup.
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the remaining calls to HCI_OP_WRITE_SCAN_ENABLE from
hci_request call chains, and converts them to hci_sync calls.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This splits hci_dev_open_sync so each stage is handle by its own
function so it is easier to identify each stage.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT core driver should addtionally check LMP feature bit
"Erroneous Data Reporting" instead of quirk
HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if
HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken.
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587
This feature indicates whether the device is able to support the
Packet_Status_Flag and the HCI commands HCI_Write_Default_-
Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_-
Data_Reporting.
the quirk was introduced by 'commit cde1a8a992 ("Bluetooth: btusb: Fix
and detect most of the Chinese Bluetooth controllers")' to mark HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT
device driver, but the reason why these two HCI commands are broken is
that feature "Erroneous Data Reporting" is not enabled by firmware, this
scenario is illustrated by below log of QCA controllers with USB I/F:
@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 288 entries
......
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
Status: Success (0x00)
Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Event HCI_Truncated_Page_Complete should belong to central
and HCI_Peripheral_Page_Response_Timeout should belong to
peripheral, but hci_set_event_mask_page_2_sync() take these
two events for wrong roles, so correct it by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
These devices are likely going to be reprogrammed when disconnected so
this avoid a whole bunch of commands attempt to remove and the add back
to the list.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
When programming a new entry into the resolving list it shall default
to network mode since the params may contain the mode programmed when
the device was last added to the resolving list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 853b70b506 ("Bluetooth: hci_sync: Set Privacy Mode when updating the resolving list")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
After resuming, remove setting scanning_paused to false, because it is
checked and set to false in hci_resume_scan_sync. Also move setting
the value to false before updating passive scan, because the value is
used when resuming passive scan.
Fixes: 3b42055388 (Bluetooth: hci_sync: Fix attempting to suspend with
unfiltered passive scan)
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The scan response and advertising data needs to be tracked on a per
instance (adv_info) since when these instaces are removed so are their
data, to fix that new flags are introduced which is used to mark when
the data changes and then checked to confirm when the data needs to be
synced with the controller.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
`cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
commit [1] to ensure that power_on work is canceled after HCI interface
down.
But, in certain cases power_on work function may call hci_dev_close_sync
itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
happens when device is rfkilled on boot. To avoid deadlock, move
power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.
Deadlock introduced by commit [1] was reported in [2,3] as broken
suspend. Suspend did not work because `hdev->req_lock` held as result of
`power_on` work deadlock. In fact, other BT features were not working.
It was not observed when testing [1] since it was verified without
rfkill in place.
NOTE: It is not needed to cancel power_on work from other places where
hci_dev_do_close/hci_dev_close_sync is called in case:
* Requests were serialized due to `hdev->req_workqueue`. The power_on
work is first in that workqueue.
* hci_rfkill_set_block which won't close device anyway until HCI_SETUP
is on.
* hci_sock_release which runs after hci_sock_bind which ensures
HCI_SETUP was cleared.
As result, behaviour is the same as in pre-dd06ed7 commit, except
power_on work cancel added to hci_dev_close.
[1]: commit ff7f292611 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
[2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
[2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/
Fixes: ff7f292611 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Reported-by: Max Krummenacher <max.krummenacher@toradex.com>
Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.
It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32. It shoudln't have been a bitmap in the first
place. The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.
The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.
So just use a regular integer.
In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).
That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit 0a97953fd2 ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.
Fixes: fe92ee6425 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspending the passive scanning _must_ have its filter_policy set
to 0x01 to use the accept list otherwise _any_ advertise report would
end up waking up the system.
In order to fix the filter_policy the code now checks for
hdev->suspended && HCI_CONN_FLAG_REMOTE_WAKEUP
first, since the MGMT_OP_SET_DEVICE_FLAGS will reject any attempt to
set HCI_CONN_FLAG_REMOTE_WAKEUP when it cannot be programmed in the
acceptlist, so it can return success causing the proper filter_policy
to be used.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215768
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move power_on work cancel to hci_dev_close_sync to ensure that power_on
work is canceled after HCI interface down, power off, rfkill, etc.
For example, if
hciconfig hci0 down
is done early enough during boot, it may run before power_on work.
Then, power_on work will actually bring up interface despite above
hciconfig command.
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This prints warnings for controllers setting broken quirks to increase
their visibility and warn about broken controllers firmware that
probably needs updates to behave properly.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This attempts to cleanup the hci_conn if it cannot be aborted as
otherwise it would likely result in having the controller and host
stack out of sync with respect to connection handle.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some controllers have problems with being sent a command to clear
all filtering. While the HCI code does not unconditionally
send a clear-all anymore at BR/EDR setup (after the state machine
refactor), there might be more ways of hitting these codepaths
in the future as the kernel develops.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
clang static analysis reports this problem
hci_sync.c:4428:2: warning: Undefined or garbage value
returned to caller
return err;
^~~~~~~~~~
If there are no connections this function is a noop but
err is never set and a false error could be reported.
Return 0 as other hci_* functions do.
Fixes: 182ee45da0 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_cmd_sync_queue can be called multiple times, each adding a
hci_cmd_sync_work_entry, before hci_cmd_sync_work is run so this makes
sure they are all dequeued properly otherwise it creates a backlog of
entries that are never run.
Link: https://lore.kernel.org/all/CAJCQCtSeUtHCgsHXLGrSTWKmyjaQDbDNpP4rb0i+RE+L2FTXSA@mail.gmail.com/T/
Fixes: 6a98e3836f ("Bluetooth: Add helper for serialized HCI command execution")
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using hci_le_create_conn_sync it shall wait for the conn_timeout
since the connection complete may take longer than just 2 seconds.
Also fix the masking of HCI_EV_LE_ENHANCED_CONN_COMPLETE and
HCI_EV_LE_CONN_COMPLETE so they are never both set so we can predict
which one the controller will use in case of HCI_OP_LE_CREATE_CONN.
Fixes: 6cd29ec6ae ("Bluetooth: hci_sync: Wait for proper events when connecting LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_update_accept_list_sync is returning the filter based on the error
but that gets overwritten by hci_le_set_addr_resolution_enable_sync
return instead of using the actual result of the likes of
hci_le_add_accept_list_sync which was intended.
Fixes: ad383c2c65 ("Bluetooth: hci_sync: Enable advertising when LL privacy is enabled")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous commit e04480920d ("Bluetooth: defer cleanup of resources
in hci_unregister_dev()") defers all destructive actions to
hci_release_dev() to prevent cocurrent problems like NPD, UAF.
However, there are still some exceptions that are ignored.
The smp_unregister() in hci_dev_close_sync() (previously in
hci_dev_do_close) will release resources like the sensitive channel
and the smp_dev objects. Consider the situations the device is detaching
or power down while the kernel is still operating on it, the following
data race could take place.
thread-A hci_dev_close_sync | thread-B read_local_oob_ext_data
|
hci_dev_unlock() |
... | hci_dev_lock()
if (hdev->smp_data) |
chan = hdev->smp_data |
| chan = hdev->smp_data (3)
|
hdev->smp_data = NULL (1) | if (!chan || !chan->data) (4)
... |
smp = chan->data | smp = chan->data
if (smp) |
chan->data = NULL (2) |
... |
kfree_sensitive(smp) |
| // dereference smp trigger UFA
That is, the objects hdev->smp_data and chan->data both suffer from the
data races. In a preempt-enable kernel, the above schedule (when (3) is
before (1) and (4) is before (2)) leads to UAF bugs. It can be
reproduced in the latest kernel and below is part of the report:
[ 49.097146] ================================================================
[ 49.097611] BUG: KASAN: use-after-free in smp_generate_oob+0x2dd/0x570
[ 49.097611] Read of size 8 at addr ffff888006528360 by task generate_oob/155
[ 49.097611]
[ 49.097611] Call Trace:
[ 49.097611] <TASK>
[ 49.097611] dump_stack_lvl+0x34/0x44
[ 49.097611] print_address_description.constprop.0+0x1f/0x150
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] kasan_report.cold+0x7f/0x11b
[ 49.097611] ? smp_generate_oob+0x2dd/0x570
[ 49.097611] smp_generate_oob+0x2dd/0x570
[ 49.097611] read_local_oob_ext_data+0x689/0xc30
[ 49.097611] ? hci_event_packet+0xc80/0xc80
[ 49.097611] ? sysvec_apic_timer_interrupt+0x9b/0xc0
[ 49.097611] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 49.097611] ? mgmt_init_hdev+0x1c/0x240
[ 49.097611] ? mgmt_init_hdev+0x28/0x240
[ 49.097611] hci_sock_sendmsg+0x1880/0x1e70
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] ? create_monitor_event+0x890/0x890
[ 49.097611] sock_sendmsg+0xdf/0x110
[ 49.097611] __sys_sendto+0x19e/0x270
[ 49.097611] ? __ia32_sys_getpeername+0xa0/0xa0
[ 49.097611] ? kernel_fpu_begin_mask+0x1c0/0x1c0
[ 49.097611] __x64_sys_sendto+0xd8/0x1b0
[ 49.097611] ? syscall_exit_to_user_mode+0x1d/0x40
[ 49.097611] do_syscall_64+0x3b/0x90
[ 49.097611] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 49.097611] RIP: 0033:0x7f5a59f51f64
...
[ 49.097611] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5a59f51f64
[ 49.097611] RDX: 0000000000000007 RSI: 00007f5a59d6ac70 RDI: 0000000000000006
[ 49.097611] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 49.097611] R10: 0000000000000040 R11: 0000000000000246 R12: 00007ffec26916ee
[ 49.097611] R13: 00007ffec26916ef R14: 00007f5a59d6afc0 R15: 00007f5a59d6b700
To solve these data races, this patch places the smp_unregister()
function in the protected area by the hci_dev_lock(). That is, the
smp_unregister() function can not be concurrently executed when
operating functions (most of them are mgmt operations in mgmt.c) hold
the device lock.
This patch is tested with kernel LOCK DEBUGGING enabled. The price from
the extended holding time of the device lock is supposed to be low as the
smp_unregister() function is fairly short and efficient.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_cmd_sync_queue shall return an error if HCI_UNREGISTER flag has
been set as that means hci_unregister_dev has been called so it will
likely cause a uaf after the timeout as the hdev will be freed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the following warning:
net/bluetooth/hci_sync.c:5143:5: warning: no previous prototype for
‘hci_le_ext_create_conn_sync’ [-Wmissing-prototypes]
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If controller/driver don't support LE simultaneous roles its UUID shall
be omitted when responding to MGMT_OP_READ_EXP_FEATURES_INFO.
This also rework the support introducing HCI_LE_SIMULTANEOUS_ROLES flag
so it can be detected when userspace wants to use or not.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This attempts to check if the controller can act as both central and
peripheral simultaneously and in case it does skip suspending
advertising or in case of directed advertising don't fail if scanning.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using HCI_OP_LE_CREATE_CONN wait for HCI_EV_LE_CONN_COMPLETE before
completing it and for HCI_OP_LE_EXT_CREATE_CONN wait for
HCI_EV_LE_ENHANCED_CONN_COMPLETE before resuming advertising.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for waiting for specific LE subevents instead of
command status which may only indicate that the commands is in progress
and a different event is used to complete the operation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds hci_le_create_conn_sync and make hci_le_connect use it instead
of queueing multiple commands which may conflict with the likes of
hci_update_passive_scan which uses hci_cmd_sync_queue.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
syzbot reported that hci_cmd_sync_cancel may sleep from the wrong
context. To avoid this, create a new work item that pushes the relevant
parts into a different context.
Note that we keep the old implementation with the name
__hci_cmd_sync_cancel as the sleeping behaviour is desired in some
cases.
Reported-and-tested-by: syzbot+485cc00ea7cf41dfdbf1@syzkaller.appspotmail.com
Fixes: c97a747efc ("Bluetooth: btusb: Cancel sync commands for certain URB errors")
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_pause_advertising_sync shall always pause advertising until
hci_resume_advertising_sync but instance 0x00 doesn't count
in adv_instance_cnt so it was causing it to be skipped.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for Set Privacy Mode when updating the resolving list
when HCI_CONN_FLAG_DEVICE_PRIVACY so the controller shall use Device
Mode for devices programmed in the resolving list, Device Mode is
actually required when the remote device are not able to use RPA as
otherwise the default mode is Network Privacy Mode in which only
allows RPAs thus the controller would filter out advertisement using
identity addresses for which there is an IRK.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reworks hci_conn_params flags to use bitmap_* helpers and add
support for setting the supported flags in hdev->conn_flags so it can
easily be accessed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some devices have a bug causing them to not work if they query
LE tx power on startup. Thus we add a quirk in order to not query it
and default min/max tx power values to HCI_TX_POWER_INVALID.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Tested-by: Orlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea521 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After transfer errors it makes sense to cancel an ongoing synchronous
command that cannot complete anymore. To permit this, export the old
hci_req_sync_cancel function as hci_cmd_sync_cancel in the API.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes MGMT_OP_SET_CONNEABLE use hci_cmd_sync_queue instead of
use a dedicated connetable_update work.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes MGMT_OP_SET_DISCOVERABLE use hci_cmd_sync_queue instead of
use a dedicated discoverable_update work.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
10bbffa3e8 attempted to fix the use of rotation duration as
advertising duration but it didn't change the if condition which still
uses the duration instead of the timeout.
Fixes: 10bbffa3e8 ("Bluetooth: Fix using advertising instance duration as timeout")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the following warnings:
>> net/bluetooth/hci_sync.c:1333:5: warning: no previous prototype for
'hci_scan_disable_sync' [-Wmissing-prototypes]
1333 | int hci_scan_disable_sync(struct hci_dev *hdev, bool rpa_le_conn)
| ^~~~~~~~~~~~~~~~~~~~~
>> net/bluetooth/hci_sync.c:1762:5: warning: no previous prototype for
'hci_passive_scan_sync' [-Wmissing-prototypes]
1762 | int hci_passive_scan_sync(struct hci_dev *hdev)
| ^~~~~~~~~~~~~~~~~~~~~
Fixes: e8907f7654 ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes hci_suspend_notifier use the hci_*_sync which can be
executed synchronously which is allowed in the suspend_notifier and
simplifies a lot of the handling since the status of each command can
be checked inline so no other work need to be scheduled thus can be
performed without using of a state machine.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves the init stages to use the hci_sync infra and in addition
to that have the stages as function tables so it is easier to change
the command sequence.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mgmt-tester paths:
Set SSP on - Success 2
Set Device ID - SSP off and Power on
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
New functions:
hci_read_local_oob_data_sync
This function requires all of the data from the cmd cmplt event
to be passed up to the caller via the skb.
mgmt-tester paths:
Read Local OOB Data - Not powered
Read Local OOB Data - Legacy pairing
Read Local OOB Data - Success SSP
Read Local OOB Data - Success SC
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Synchronous version of MGMT_OP_GET_CONN_INFO
Implements:
hci_read_rssi_sync
hci_read_tx_power_sync
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
