Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As per RFC4443, the destination address field for ICMPv6 error messages
is copied from the source address field of the invoking packet.
In configurations with Virtual Routing and Forwarding tables, looking up
which routing table to use for sending ICMPv6 error messages is
currently done by using the destination net_device.
If the source and destination interfaces are within separate VRFs, or
one in the global routing table and the other in a VRF, looking up the
source address of the invoking packet in the destination interface's
routing table will fail if the destination interface's routing table
contains no route to the invoking packet's source address.
One observable effect of this issue is that traceroute6 does not work in
the following cases:
- Route leaking between global routing table and VRF
- Route leaking between VRFs
Use the source device routing table when sending ICMPv6 error
messages.
[ In the context of ipv4, it has been pointed out that a similar issue
may exist with ICMP errors triggered when forwarding between network
namespaces. It would be worthwhile to investigate whether ipv6 has
similar issues, but is outside of the scope of this investigation. ]
[ Testing shows that similar issues exist with ipv6 unreachable /
fragmentation needed messages. However, investigation of this
additional failure mode is beyond this investigation's scope. ]
Link: https://tools.ietf.org/html/rfc4443
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop repeated words in net/ipv6/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple fixes which require no deep knowledge of the code.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Bareudp tunnel module provides a generic L3 encapsulation
tunnelling module for tunnelling different protocols like MPLS,
IP,NSH etc inside a UDP tunnel.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of generally passing NULL to NF_HOOK_COND() for input device,
pass skb->dev which contains input device for routed skbs.
Note that iptables (both legacy and nft) reject rules with input
interface match from being added to POSTROUTING chains, but nftables
allows this.
Cc: Eric Garver <eric@garver.life>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Thomas found that some forwarded packets would be stuck
in FQ packet scheduler because their skb->tstamp contained
timestamps far in the future.
We thought we addressed this point in commit 8203e2d844
("net: clear skb->tstamp in forwarding paths") but there
is still an issue when/if a packet needs to be fragmented.
In order to meet EDT requirements, we have to make sure all
fragments get the original skb->tstamp.
Note that this original skb->tstamp should be zero in
forwarding path, but might have a non zero value in
output path if user decided so.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thomas Bartschies <Thomas.Bartschies@cvk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ip6_xmit() sets skb->priority based on sk->sk_priority
This is not desirable for TCP since TCP shares the same ctl socket
for a given netns. We want to be able to send RST or ACK packets
with a non zero skb->priority.
This patch has no functional change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting skb->mark for UDP and RAW sockets using cmsg.
This is analogous to existing support for TOS, TTL, txtime, etc.
Packet sockets already support this as of commit c7d39e3263
("packet: support per-packet fwmark for af_packet sendmsg").
Similar to other fields, implement by
1. initialize the sockcm_cookie.mark from socket option sk_mark
2. optionally overwrite this in ip_cmsg_send/ip6_datagram_send_ctl
3. initialize inet_cork.mark from sockcm_cookie.mark
4. initialize each (usually just one) skb->mark from inet_cork.mark
Step 1 is handled in one location for most protocols by ipcm_init_sk
as of commit 351782067b ("ipv4: ipcm_cookie initializers").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change in this patch, it only prepares the next one.
rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const
variables.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The below patch fixes an incorrect zerocopy refcnt increment when
appending with MSG_MORE to an existing zerocopy udp skb.
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt 1
send(.., MSG_ZEROCOPY | MSG_MORE); // refcnt still 1 (bar frags)
But it missed that zerocopy need not be passed at the first send. The
right test whether the uarg is newly allocated and thus has extra
refcnt 1 is not !skb, but !skb_zcopy.
send(.., MSG_MORE); // <no uarg>
send(.., MSG_ZEROCOPY); // refcnt 1
Fixes: 100f6d8e09 ("net: correct zerocopy refcnt with udp MSG_MORE")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-05-31
The following pull-request contains BPF updates for your *net-next* tree.
Lots of exciting new features in the first PR of this developement cycle!
The main changes are:
1) misc verifier improvements, from Alexei.
2) bpftool can now convert btf to valid C, from Andrii.
3) verifier can insert explicit ZEXT insn when requested by 32-bit JITs.
This feature greatly improves BPF speed on 32-bit architectures. From Jiong.
4) cgroups will now auto-detach bpf programs. This fixes issue of thousands
bpf programs got stuck in dying cgroups. From Roman.
5) new bpf_send_signal() helper, from Yonghong.
6) cgroup inet skb programs can signal CN to the stack, from Lawrence.
7) miscellaneous cleanups, from many developers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update BPF_CGROUP_RUN_PROG_INET_EGRESS() callers to support returning
congestion notifications from the BPF programs.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
TCP zerocopy takes a uarg reference for every skb, plus one for the
tcp_sendmsg_locked datapath temporarily, to avoid reaching refcnt zero
as it builds, sends and frees skbs inside its inner loop.
UDP and RAW zerocopy do not send inside the inner loop so do not need
the extra sock_zerocopy_get + sock_zerocopy_put pair. Commit
52900d22288ed ("udp: elide zerocopy operation in hot path") introduced
extra_uref to pass the initial reference taken in sock_zerocopy_alloc
to the first generated skb.
But, sock_zerocopy_realloc takes this extra reference at the start of
every call. With MSG_MORE, no new skb may be generated to attach the
extra_uref to, so refcnt is incorrectly 2 with only one skb.
Do not take the extra ref if uarg && !tcp, which implies MSG_MORE.
Update extra_uref accordingly.
This conditional assignment triggers a false positive may be used
uninitialized warning, so have to initialize extra_uref at define.
Changes v1->v2: fix typo in Fixes SHA1
Fixes: 52900d2228 ("udp: elide zerocopy operation in hot path")
Reported-by: syzbot <syzkaller@googlegroups.com>
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes a new API to refragment a skbuff. This allows you to
split either a linear skbuff or to force the refragmentation of an
existing fraglist using a different mtu. The API consists of:
* ip6_frag_init(), that initializes the internal state of the transformer.
* ip6_frag_next(), that allows you to fetch the next fragment. This function
internally allocates the skbuff that represents the fragment, it pushes
the IPv6 header, and it also copies the payload for each fragment.
The ip6_frag_state object stores the internal state of the splitter.
This code has been extracted from ip6_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the skbuff fraglist split iterator. This API provides an
iterator to transform the fraglist into single skbuff objects, it
consists of:
* ip6_fraglist_init(), that initializes the internal state of the
fraglist iterator.
* ip6_fraglist_prepare(), that restores the IPv6 header on the fragment.
* ip6_fraglist_next(), that retrieves the fragment from the fraglist and
updates the internal state of the iterator to point to the next
fragment in the fraglist.
The ip6_fraglist_iter object stores the internal state of the iterator.
This code has been extracted from ip6_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A later patch allows an IPv6 gateway with an IPv4 route. The neighbor
entry will exist in the v6 ndisc table and the cached header will contain
the ipv6 protocol which is wrong for an IPv4 packet. For an IPv4 packet to
use the v6 neighbor entry, neigh_output needs to skip the cached header
and just use the output callback for the neigh entry.
A future patchset can look at expanding the hh_cache to handle 2
protocols. For now, IPv6 gateways with an IPv4 route will take the
extra overhead of generating the header.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of ip6_fragment func, the prevhdr pointer is
obtained in the ip6_find_1stfragopt func.
However, all the pointers pointing into skb header may change
when calling skb_checksum_help func with
skb->ip_summed = CHECKSUM_PARTIAL condition.
The prevhdr pointe will be dangling if it is not reloaded after
calling __skb_linearize func in skb_checksum_help func.
Here, I add a variable, nexthdr_offset, to evaluate the offset,
which does not changes even after calling __skb_linearize func.
Fixes: 405c92f7a5 ("ipv6: add defensive check for CHECKSUM_PARTIAL skbs in ip_fragment")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Reported-by: syzbot+e8ce541d095e486074fc@syzkaller.appspotmail.com
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default IPv6 socket with IPV6_ROUTER_ALERT socket option set will
receive all IPv6 RA packets from all namespaces.
IPV6_ROUTER_ALERT_ISOLATE socket option restricts packets received by
the socket to be only from the socket's namespace.
Signed-off-by: Maxim Martynov <maxim@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an optional extension infrastructure, with ispec (xfrm) and
bridge netfilter as first users.
objdiff shows no changes if kernel is built without xfrm and br_netfilter
support.
The third (planned future) user is Multipath TCP which is still
out-of-tree.
MPTCP needs to map logical mptcp sequence numbers to the tcp sequence
numbers used by individual subflows.
This DSS mapping is read/written from tcp option space on receive and
written to tcp option space on transmitted tcp packets that are part of
and MPTCP connection.
Extending skb_shared_info or adding a private data field to skb fclones
doesn't work for incoming skb, so a different DSS propagation method would
be required for the receive side.
mptcp has same requirements as secpath/bridge netfilter:
1. extension memory is released when the sk_buff is free'd.
2. data is shared after cloning an skb (clone inherits extension)
3. adding extension to an skb will COW the extension buffer if needed.
The "MPTCP upstreaming" effort adds SKB_EXT_MPTCP extension to store the
mapping for tx and rx processing.
Two new members are added to sk_buff:
1. 'active_extensions' byte (filling a hole), telling which extensions
are available for this skb.
This has two purposes.
a) avoids the need to initialize the pointer.
b) allows to "delete" an extension by clearing its bit
value in ->active_extensions.
While it would be possible to store the active_extensions byte
in the extension struct instead of sk_buff, there is one problem
with this:
When an extension has to be disabled, we can always clear the
bit in skb->active_extensions. But in case it would be stored in the
extension buffer itself, we might have to COW it first, if
we are dealing with a cloned skb. On kmalloc failure we would
be unable to turn an extension off.
2. extension pointer, located at the end of the sk_buff.
If the active_extensions byte is 0, the pointer is undefined,
it is not initialized on skb allocation.
This adds extra code to skb clone and free paths (to deal with
refcount/free of extension area) but this replaces similar code that
manages skb->nf_bridge and skb->sp structs in the followup patches of
the series.
It is possible to add support for extensions that are not preseved on
clones/copies.
To do this, it would be needed to define a bitmask of all extensions that
need copy/cow semantics, and change __skb_ext_copy() to check
->active_extensions & SKB_EXT_PRESERVE_ON_CLONE, then just set
->active_extensions to 0 on the new clone.
This isn't done here because all extensions that get added here
need the copy/cow semantics.
v2:
Allocate entire extension space using kmem_cache.
Upside is that this allows better tracking of used memory,
downside is that we will allocate more space than strictly needed in
most cases (its unlikely that all extensions are active/needed at same
time for same skb).
The allocated memory (except the small extension header) is not cleared,
so no additonal overhead aside from memory usage.
Avoid atomic_dec_and_test operation on skb_ext_put()
by using similar trick as kfree_skbmem() does with fclone_ref:
If recount is 1, there is no concurrent user and we can free right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergey reported that forwarding was no longer working
if fq packet scheduler was used.
This is caused by the recent switch to EDT model, since incoming
packets might have been timestamped by __net_timestamp()
__net_timestamp() uses ktime_get_real(), while fq expects packets
using CLOCK_MONOTONIC base.
The fix is to clear skb->tstamp in forwarding paths.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
extra_uref is used in __ip(6)_append_data only if uarg is set.
Smatch sees that the variable is passed to sock_zerocopy_put_abort.
This function accesses it only when uarg is set, but smatch cannot
infer this.
Make this dependency explicit.
Fixes: 52900d2228 ("udp: elide zerocopy operation in hot path")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if we send an IPv6 packet without options, MAX_HEADER might not be
enough to account for the additional headroom required by alignment of
hardware headers.
On a configuration without HYPERV_NET, WLAN, AX25, and with IPV6_TUNNEL,
sending short SCTP packets over IPv4 over L2TP over IPv6, we start with
100 bytes of allocated headroom in sctp_packet_transmit(), end up with 54
bytes after l2tp_xmit_skb(), and 14 bytes in ip6_finish_output2().
Those would be enough to append our 14 bytes header, but we're going to
align that to 16 bytes, and write 2 bytes out of the allocated slab in
neigh_hh_output().
KASan says:
[ 264.967848] ==================================================================
[ 264.967861] BUG: KASAN: slab-out-of-bounds in ip6_finish_output2+0x1aec/0x1c70
[ 264.967866] Write of size 16 at addr 000000006af1c7fe by task netperf/6201
[ 264.967870]
[ 264.967876] CPU: 0 PID: 6201 Comm: netperf Not tainted 4.20.0-rc4+ #1
[ 264.967881] Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
[ 264.967887] Call Trace:
[ 264.967896] ([<00000000001347d6>] show_stack+0x56/0xa0)
[ 264.967903] [<00000000017e379c>] dump_stack+0x23c/0x290
[ 264.967912] [<00000000007bc594>] print_address_description+0xf4/0x290
[ 264.967919] [<00000000007bc8fc>] kasan_report+0x13c/0x240
[ 264.967927] [<000000000162f5e4>] ip6_finish_output2+0x1aec/0x1c70
[ 264.967935] [<000000000163f890>] ip6_finish_output+0x430/0x7f0
[ 264.967943] [<000000000163fe44>] ip6_output+0x1f4/0x580
[ 264.967953] [<000000000163882a>] ip6_xmit+0xfea/0x1ce8
[ 264.967963] [<00000000017396e2>] inet6_csk_xmit+0x282/0x3f8
[ 264.968033] [<000003ff805fb0ba>] l2tp_xmit_skb+0xe02/0x13e0 [l2tp_core]
[ 264.968037] [<000003ff80631192>] l2tp_eth_dev_xmit+0xda/0x150 [l2tp_eth]
[ 264.968041] [<0000000001220020>] dev_hard_start_xmit+0x268/0x928
[ 264.968069] [<0000000001330e8e>] sch_direct_xmit+0x7ae/0x1350
[ 264.968071] [<000000000122359c>] __dev_queue_xmit+0x2b7c/0x3478
[ 264.968075] [<00000000013d2862>] ip_finish_output2+0xce2/0x11a0
[ 264.968078] [<00000000013d9b14>] ip_finish_output+0x56c/0x8c8
[ 264.968081] [<00000000013ddd1e>] ip_output+0x226/0x4c0
[ 264.968083] [<00000000013dbd6c>] __ip_queue_xmit+0x894/0x1938
[ 264.968100] [<000003ff80bc3a5c>] sctp_packet_transmit+0x29d4/0x3648 [sctp]
[ 264.968116] [<000003ff80b7bf68>] sctp_outq_flush_ctrl.constprop.5+0x8d0/0xe50 [sctp]
[ 264.968131] [<000003ff80b7c716>] sctp_outq_flush+0x22e/0x7d8 [sctp]
[ 264.968146] [<000003ff80b35c68>] sctp_cmd_interpreter.isra.16+0x530/0x6800 [sctp]
[ 264.968161] [<000003ff80b3410a>] sctp_do_sm+0x222/0x648 [sctp]
[ 264.968177] [<000003ff80bbddac>] sctp_primitive_ASSOCIATE+0xbc/0xf8 [sctp]
[ 264.968192] [<000003ff80b93328>] __sctp_connect+0x830/0xc20 [sctp]
[ 264.968208] [<000003ff80bb11ce>] sctp_inet_connect+0x2e6/0x378 [sctp]
[ 264.968212] [<0000000001197942>] __sys_connect+0x21a/0x450
[ 264.968215] [<000000000119aff8>] sys_socketcall+0x3d0/0xb08
[ 264.968218] [<000000000184ea7a>] system_call+0x2a2/0x2c0
[...]
Just like ip_finish_output2() does for IPv4, check that we have enough
headroom in ip6_xmit(), and reallocate it if we don't.
This issue is older than git history.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets marked with 'offload_l3_fwd_mark' were already forwarded by a
capable device and should not be forwarded again by the kernel.
Therefore, have the kernel consume them.
The check is performed in ip{,6}_forward_finish() in order to allow the
kernel to process such packets in ip{,6}_forward() and generate required
exceptions. For example, ICMP redirects.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MSG_ZEROCOPY, each skb holds a reference to a struct ubuf_info.
Release of its last reference triggers a completion notification.
The TCP stack in tcp_sendmsg_locked holds an extra ref independent of
the skbs, because it can build, send and free skbs within its loop,
possibly reaching refcount zero and freeing the ubuf_info too soon.
The UDP stack currently also takes this extra ref, but does not need
it as all skbs are sent after return from __ip(6)_append_data.
Avoid the extra refcount_inc and refcount_dec_and_test, and generally
the sock_zerocopy_put in the common path, by passing the initial
reference to the first skb.
This approach is taken instead of initializing the refcount to 0, as
that would generate error "refcount_t: increment on 0" on the
next skb_zcopy_set.
Changes
v3 -> v4
- Move skb_zcopy_set below the only kfree_skb that might cause
a premature uarg destroy before skb_zerocopy_put_abort
- Move the entire skb_shinfo assignment block, to keep that
cacheline access in one place
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend zerocopy to udp sockets. Allow setting sockopt SO_ZEROCOPY and
interpret flag MSG_ZEROCOPY.
This patch was previously part of the zerocopy RFC patchsets. Zerocopy
is not effective at small MTU. With segmentation offload building
larger datagrams, the benefit of page flipping outweights the cost of
generating a completion notification.
tools/testing/selftests/net/msg_zerocopy.sh after applying follow-on
test patch and making skb_orphan_frags_rx same as skb_orphan_frags:
ipv4 udp -t 1
tx=191312 (11938 MB) txc=0 zc=n
rx=191312 (11938 MB)
ipv4 udp -z -t 1
tx=304507 (19002 MB) txc=304507 zc=y
rx=304507 (19002 MB)
ok
ipv6 udp -t 1
tx=174485 (10888 MB) txc=0 zc=n
rx=174485 (10888 MB)
ipv6 udp -z -t 1
tx=294801 (18396 MB) txc=294801 zc=y
rx=294801 (18396 MB)
ok
Changes
v1 -> v2
- Fixup reverse christmas tree violation
v2 -> v3
- Split refcount avoidance optimization into separate patch
- Fix refcount leak on error in fragmented case
(thanks to Paolo Abeni for pointing this one out!)
- Fix refcount inc on zero
- Test sock_flag SOCK_ZEROCOPY directly in __ip_append_data.
This is needed since commit 5cf4a8532c ("tcp: really ignore
MSG_ZEROCOPY if no SO_ZEROCOPY") did the same for tcp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip packet generation, pagedlen is initialized for each skb at the
start of the loop in __ip(6)_append_data, before label alloc_new_skb.
Depending on compiler options, code can be generated that jumps to
this label, triggering use of an an uninitialized variable.
In practice, at -O2, the generated code moves the initialization below
the label. But the code should not rely on that for correctness.
Fixes: 15e36f5b8e ("udp: paged allocation with gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely case ip6_xmit() has to call skb_realloc_headroom(),
we need to call skb_set_owner_w() before consuming original skb,
otherwise we risk a use-after-free.
Bring IPv6 in line with what we do in IPv4 to fix this.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SKB is not on a list if skb->next is NULL.
Codify this convention into a helper function and use it
where we are dequeueing an SKB and need to mark it as such.
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
auto_flowlabel is enabled
For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.
Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.
Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0
After this commit:
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
Fixes: b73c3d0e4f ("net: Save TX flow hash in sock and set in skbuf on xmit")
Fixes: 67800f9b1f ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ipc(6)->gso_size is correctly initialized in all callers of
ip(6)_setup_cork, it is safe to unconditionally pass it to the cork.
Link: http://lkml.kernel.org/r/20180619164752.143249-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_shinfo(skb)->tx_flags is derived from sk->sk_tsflags, possibly
after modification by __sock_cmsg_send, by calling sock_tx_timestamp.
The IPv4 and IPv6 paths do this conversion differently. In IPv4, the
individual protocols that support tx timestamps call this function
and store the result in ipc.tx_flags. In IPv6, sock_tx_timestamp is
called in __ip6_append_data.
There is no need to store both tx_flags and ts_flags in the cookie
as one is derived from the other. Convert when setting up the cork
and remove the redundant field. This is similar to IPv6, only have
the conversion happen only once per datagram, in ip(6)_setup_cork.
Also change __ip6_append_data to match __ip_append_data. Only update
tskey if timestamping is enabled with OPT_ID. The SOCK_.. test is
redundant: only valid protocols can have non-zero cork->tx_flags.
After this change the IPv4 and IPv6 logic is the same.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipcm_cookie includes sockcm_cookie. Do the same for ipcm6_cookie.
This reduces the number of arguments that need to be passed around,
applies ipcm6_init to all cookie fields at once and reduces code
differentiation between ipv4 and ipv6.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a struct sockcm_cookie parameter to ip6_setup_cork() so
we can easily re-use the transmit_time field from struct inet_cork
for most paths, by copying the timestamp from the CMSG cookie.
This is later copied into the skb during __ip6_make_skb().
For the raw fast path, also pass the sockcm_cookie as a parameter
so we can just perform the copy at rawv6_send_hdrinc() directly.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipcm(6)_cookie field gso_size is set only in the udp path. The ip
layer copies this to cork only if sk_type is SOCK_DGRAM. This check
proved too permissive. Ping and l2tp sockets have the same type.
Limit to sockets of type SOCK_DGRAM and protocol IPPROTO_UDP to
exclude ping sockets.
v1 -> v2
- remove irrelevant whitespace changes
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the right device to determine if redirect should be sent especially
when using vrf. Same as well as when sending the redirect.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Device features may change during transmission. In particular with
corking, a device may toggle scatter-gather in between allocating
and writing to an skb.
Do not unconditionally assume that !NETIF_F_SG at write time implies
that the same held at alloc time and thus the skb has sufficient
tailroom.
This issue predates git history.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, more relevant updates in this batch are:
1) Add Maglev support to IPVS. Moreover, store lastest server weight in
IPVS since this is needed by maglev, patches from from Inju Song.
2) Preparation works to add iptables flowtable support, patches
from Felix Fietkau.
3) Hand over flows back to conntrack slow path in case of TCP RST/FIN
packet is seen via new teardown state, also from Felix.
4) Add support for extended netlink error reporting for nf_tables.
5) Support for larger timeouts that 23 days in nf_tables, patch from
Florian Westphal.
6) Always set an upper limit to dynamic sets, also from Florian.
7) Allow number generator to make map lookups, from Laura Garcia.
8) Use hash_32() instead of opencode hashing in IPVS, from Vicent Bernat.
9) Extend ip6tables SRH match to support previous, next and last SID,
from Ahmed Abdelsalam.
10) Move Passive OS fingerprint nf_osf.c, from Fernando Fernandez.
11) Expose nf_conntrack_max through ctnetlink, from Florent Fourcot.
12) Several housekeeping patches for xt_NFLOG, x_tables and ebtables,
from Taehee Yoo.
13) Unify meta bridge with core nft_meta, then make nft_meta built-in.
Make rt and exthdr built-in too, again from Florian.
14) Missing initialization of tbl->entries in IPVS, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending large datagrams that are later segmented, store data in
page frags to avoid copying from linear in skb_segment.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support generic segmentation offload for udp datagrams. Callers can
concatenate and send at once the payload of multiple datagrams with
the same destination.
To set segment size, the caller sets socket option UDP_SEGMENT to the
length of each discrete payload. This value must be smaller than or
equal to the relevant MTU.
A follow-up patch adds cmsg UDP_SEGMENT to specify segment size on a
per send call basis.
Total byte length may then exceed MTU. If not an exact multiple of
segment size, the last segment will be shorter.
The implementation adds a gso_size field to the udp socket, ip(v6)
cmsg cookie and inet_cork structure to be able to set the value at
setsockopt or cmsg time and to work with both lockless and corked
paths.
Initial benchmark numbers show UDP GSO about as expensive as TCP GSO.
tcp tso
3197 MB/s 54232 msg/s 54232 calls/s
6,457,754,262 cycles
tcp gso
1765 MB/s 29939 msg/s 29939 calls/s
11,203,021,806 cycles
tcp without tso/gso *
739 MB/s 12548 msg/s 12548 calls/s
11,205,483,630 cycles
udp
876 MB/s 14873 msg/s 624666 calls/s
11,205,777,429 cycles
udp gso
2139 MB/s 36282 msg/s 36282 calls/s
11,204,374,561 cycles
[*] after reverting commit 0a6b2a1dc2
("tcp: switch to GSO being always on")
Measured total system cycles ('-a') for one core while pinning both
the network receive path and benchmark process to that core:
perf stat -a -C 12 -e cycles \
./udpgso_bench_tx -C 12 -4 -D "$DST" -l 4
Note the reduction in calls/s with GSO. Bytes per syscall drops
increases from 1470 to 61818.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP segmentation offload needs access to inet_cork in the udp layer.
Pass the struct to ip(6)_make_skb instead of allocating it on the
stack in that function itself.
This patch is a noop otherwise.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dst entry is created from a fib entry, the 'from' in rt6_info
is set to the fib entry. The 'from' reference is used most notably for
cookie checking - making sure stale dst entries are updated if the
fib entry is changed.
When a fib entry is deleted, the pcpu routes on it are walked releasing
the fib6_info reference. This is needed for the fib6_info cleanup to
happen and to make sure all device references are released in a timely
manner.
There is a race window when a FIB entry is deleted and the 'from' on the
pcpu route is dropped and the pcpu route hits a cookie check. Handle
this race using rcu on from.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like ip_dst_mtu_maybe_forward(), to avoid a dependency with ipv6.ko.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Last step before flipping the data type for FIB entries:
- use fib6_info_alloc to create FIB entries in ip6_route_info_create
and addrconf_dst_alloc
- use fib6_info_release in place of dst_release, ip6_rt_put and
rt6_release
- remove the dst_hold before calling __ip6_ins_rt or ip6_del_rt
- when purging routes, drop per-cpu routes
- replace inc and dec of rt6i_ref with fib6_info_hold and fib6_info_release
- use rt->from since it points to the FIB entry
- drop references to exception bucket, fib6_metrics and per-cpu from
dst entries (those are relevant for fib entries only)
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics such as InHdrErrors should be counted on the ingress
netdev rather than on the dev from the dst, which is the egress.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of ip6_forward(), IPSTATS_MIB_OUTFORWDATAGRAMS and
IPSTATS_MIB_OUTOCTETS are incremented immediately before the NF_HOOK call
for NFPROTO_IPV6 / NF_INET_FORWARD. As a result, these counters get
incremented regardless of whether or not the netfilter hook allows the
packet to continue being processed. This change increments the counters
in ip6_forward_finish() so that it will not happen if the netfilter hook
chooses to terminate the packet, which is similar to how IPv4 works.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 694aba690d ("ipv4: factorize sk_wmem_alloc updates
done by __ip_append_data()") and commit 1f4c6eb240 ("ipv6:
factorize sk_wmem_alloc updates done by __ip6_append_data()"),
when transmitting sub MTU datagram, an addtional, unneeded atomic
operation is performed in ip*_append_data() to update wmem_alloc:
in the above condition the delta is 0.
The above cause small but measurable performance regression in UDP
xmit tput test with packet size below MTU.
This change avoids such overhead updating wmem_alloc only if
wmem_alloc_delta is non zero.
The error path is left intentionally unmodified: it's a slow path
and simplicity is preferred to performances.
Fixes: 694aba690d ("ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()")
Fixes: 1f4c6eb240 ("ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'connected' parameter to ip6_sk_dst_lookup_flow() and update
the cache only if ip6_sk_dst_check() returns NULL and a socket
is connected.
The function is used as before, the new behavior for UDP sockets
in udpv6_sendmsg() will be enabled in the next patch.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing my inet defrag changes, I found that the senders
could spend ~20% of cpu cycles in skb_set_owner_w() updating
sk->sk_wmem_alloc for every fragment they cook, competing
with TX completion of prior skbs possibly happening on another cpus.
The solution to this problem is to use alloc_skb() instead
of sock_wmalloc() and manually perform a single sk_wmem_alloc change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
If you take a GSO skb, and split it into packets, will the network
length (L3 headers + L4 headers + payload) of those packets be small
enough to fit within a given MTU?
skb_gso_validate_mtu gives you the answer to that question. However,
we recently added to add a way to validate the MAC length of a split GSO
skb (L2+L3+L4+payload), and the names get confusing, so rename
skb_gso_validate_mtu to skb_gso_validate_network_len
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipmr the mr_table socket is handled under RCU. Introduce the same
for ip6mr.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 513674b5a2 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.
The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled. Fix it to return the effective value, whether
that has been set at the socket or net namespace level.
Fixes: 513674b5a2 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my last patch, I missed fact that cork.base.dst was not initialized
in ip6_make_skb() :
If ip6_setup_cork() returns an error, we might attempt a dst_release()
on some random pointer.
Fixes: 862c03ee1d ("ipv6: fix possible mem leaks in ipv6_make_skb()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_setup_cork() might return an error, while memory allocations have
been done and must be rolled back.
Fixes: 6422398c2a ("ipv6: introduce ipv6_make_skb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Reported-by: Mike Maloney <maloney@google.com>
Acked-by: Mike Maloney <maloney@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IPv6 flow table type, that implements the datapath
flow table to forward IPv6 traffic.
This patch exports ip6_dst_mtu_forward() that is required to check for
mtu to pass up packets that need PMTUD handling to the classic
forwarding path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If SNAT modifies the source address the resulting packet might match
an IPsec policy, reinject the packet if that's the case.
The exact same thing is already done for IPv4.
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl.ip6.auto_flowlabels is default 1. In our hosts, we set it to 2.
If sockopt doesn't set autoflowlabel, outcome packets from the hosts are
supposed to not include flowlabel. This is true for normal packet, but
not for reset packet.
The reason is ipv6_pinfo.autoflowlabel is set in sock creation. Later if
we change sysctl.ip6.auto_flowlabels, the ipv6_pinfo.autoflowlabel isn't
changed, so the sock will keep the old behavior in terms of auto
flowlabel. Reset packet is suffering from this problem, because reset
packet is sent from a special control socket, which is created at boot
time. Since sysctl.ipv6.auto_flowlabels is 1 by default, the control
socket will always have its ipv6_pinfo.autoflowlabel set, even after
user set sysctl.ipv6.auto_flowlabels to 1, so reset packset will always
have flowlabel. Normal sock created before sysctl setting suffers from
the same issue. We can't even turn off autoflowlabel unless we kill all
socks in the hosts.
To fix this, if IPV6_AUTOFLOWLABEL sockopt is used, we use the
autoflowlabel setting from user, otherwise we always call
ip6_default_np_autolabel() which has the new settings of sysctl.
Note, this changes behavior a little bit. Before commit 42240901f7
(ipv6: Implement different admin modes for automatic flow labels), the
autoflowlabel behavior of a sock isn't sticky, eg, if sysctl changes,
existing connection will change autoflowlabel behavior. After that
commit, autoflowlabel behavior is sticky in the whole life of the sock.
With this patch, the behavior isn't sticky again.
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <tom@quantonium.net>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first member of an IPSEC route bundle chain sets it's dst->path to
the underlying ipv4/ipv6 route that carries the bundle.
Stated another way, if one were to follow the xfrm_dst->child chain of
the bundle, the final non-NULL pointer would be the path and point to
either an ipv4 or an ipv6 route.
This is largely used to make sure that PMTU events propagate down to
the correct ipv4 or ipv6 route.
When we don't have the top of an IPSEC bundle 'dst->path == dst'.
Move it down into xfrm_dst and key off of dst->xfrm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
When syzkaller team brought us a C repro for the crash [1] that
had been reported many times in the past, I finally could find
the root cause.
If FlowLabel info is merged by fl6_merge_options(), we leave
part of the opt_space storage provided by udp/raw/l2tp with random value
in opt_space.tot_len, unless a control message was provided at sendmsg()
time.
Then ip6_setup_cork() would use this random value to perform a kzalloc()
call. Undefined behavior and crashes.
Fix is to properly set tot_len in fl6_merge_options()
At the same time, we can also avoid consuming memory and cpu cycles
to clear it, if every option is copied via a kmemdup(). This is the
change in ip6_setup_cork().
[1]
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 6613 Comm: syz-executor0 Not tainted 4.14.0-rc4+ #127
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801cb64a100 task.stack: ffff8801cc350000
RIP: 0010:ip6_setup_cork+0x274/0x15c0 net/ipv6/ip6_output.c:1168
RSP: 0018:ffff8801cc357550 EFLAGS: 00010203
RAX: dffffc0000000000 RBX: ffff8801cc357748 RCX: 0000000000000010
RDX: 0000000000000002 RSI: ffffffff842bd1d9 RDI: 0000000000000014
RBP: ffff8801cc357620 R08: ffff8801cb17f380 R09: ffff8801cc357b10
R10: ffff8801cb64a100 R11: 0000000000000000 R12: ffff8801cc357ab0
R13: ffff8801cc357b10 R14: 0000000000000000 R15: ffff8801c3bbf0c0
FS: 00007f9c5c459700(0000) GS:ffff8801db200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020324000 CR3: 00000001d1cf2000 CR4: 00000000001406f0
DR0: 0000000020001010 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000600
Call Trace:
ip6_make_skb+0x282/0x530 net/ipv6/ip6_output.c:1729
udpv6_sendmsg+0x2769/0x3380 net/ipv6/udp.c:1340
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:762
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
SYSC_sendto+0x358/0x5a0 net/socket.c:1750
SyS_sendto+0x40/0x50 net/socket.c:1718
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4520a9
RSP: 002b:00007f9c5c458c08 EFLAGS: 00000216 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 00000000004520a9
RDX: 0000000000000001 RSI: 0000000020fd1000 RDI: 0000000000000016
RBP: 0000000000000086 R08: 0000000020e0afe4 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000216 R12: 00000000004bb1ee
R13: 00000000ffffffff R14: 0000000000000016 R15: 0000000000000029
Code: e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 ea 0f 00 00 48 8d 79 04 48 b8 00 00 00 00 00 fc ff df 45 8b 74 24 04 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85
RIP: ip6_setup_cork+0x274/0x15c0 net/ipv6/ip6_output.c:1168 RSP: ffff8801cc357550
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 2465 defines ipv6IfStatsOutFragFails as:
"The number of IPv6 datagrams that have been discarded
because they needed to be fragmented at this output
interface but could not be."
The existing implementation, instead, would increase the counter
twice in case we fail to allocate room for single fragments:
once for the fragment, once for the datagram.
This didn't look intentional though. In one of the two affected
affected failure paths, the double increase was simply a result
of a new 'goto fail' statement, introduced to avoid a skb leak.
The other path appears to be affected since at least 2.6.12-rc2.
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Fixes: 1d325d217c ("ipv6: ip6_fragment: fix headroom tests and skb leak")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our customer encountered stuck NFS writes for blocks starting at specific
offsets w.r.t. page boundary caused by networking stack sending packets via
UFO enabled device with wrong checksum. The problem can be reproduced by
composing a long UDP datagram from multiple parts using MSG_MORE flag:
sendto(sd, buff, 1000, MSG_MORE, ...);
sendto(sd, buff, 1000, MSG_MORE, ...);
sendto(sd, buff, 3000, 0, ...);
Assume this packet is to be routed via a device with MTU 1500 and
NETIF_F_UFO enabled. When second sendto() gets into __ip_append_data(),
this condition is tested (among others) to decide whether to call
ip_ufo_append_data():
((length + fragheaderlen) > mtu) || (skb && skb_is_gso(skb))
At the moment, we already have skb with 1028 bytes of data which is not
marked for GSO so that the test is false (fragheaderlen is usually 20).
Thus we append second 1000 bytes to this skb without invoking UFO. Third
sendto(), however, has sufficient length to trigger the UFO path so that we
end up with non-UFO skb followed by a UFO one. Later on, udp_send_skb()
uses udp_csum() to calculate the checksum but that assumes all fragments
have correct checksum in skb->csum which is not true for UFO fragments.
When checking against MTU, we need to add skb->len to length of new segment
if we already have a partially filled skb and fragheaderlen only if there
isn't one.
In the IPv6 case, skb can only be null if this is the first segment so that
we have to use headersize (length of the first IPv6 header) rather than
fragheaderlen (length of IPv6 header of further fragments) for skb == NULL.
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Fixes: e4c5e13aa4 ("ipv6: Should use consistent conditional judgement for
ip6 fragment between __ip6_append_data and ip6_finish_output")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipv6 tx path, rcu_read_lock() is taken so that dst won't get freed
during the execution of ip6_fragment(). Hence, no need to hold dst in
it.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After moves the skb->dev and skb->protocol initialization into
ip6_output, setting the skb->dev inside ip6_fragment is unnecessary.
Fixes: 97a7a37a7b7b("ipv6: Initial skb->dev and skb->protocol in ip6_output")
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the initialization of skb->dev and skb->protocol from
ip6_finish_output2 to ip6_output. This can make the skb->dev and
skb->protocol information avalaible to the CGROUP eBPF filter.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov and idaifish@gmail.com reported crashes caused by
one skb shared_info being overwritten from __ip6_append_data()
Andrey program lead to following state :
copy -4200 datalen 2000 fraglen 2040
maxfraglen 2040 alloclen 2048 transhdrlen 0 offset 0 fraggap 6200
The skb_copy_and_csum_bits(skb_prev, maxfraglen, data + transhdrlen,
fraggap, 0); is overwriting skb->head and skb_shared_info
Since we apparently detect this rare condition too late, move the
code earlier to even avoid allocating skb and risking crashes.
Once again, many thanks to Andrey and syzkaller team.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: <idaifish@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use unsigned variables to see if it returns a negative
error or not.
Fixes: 2423496af3 ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned. If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.
However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.
In case original skb is cloned this munges nexthdr value of another
skb. Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.
This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active: tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c146066ab8 ("ipv4: Don't use ufo handling on later transformed
packets") and commit f89c56ce71 ("ipv6: Don't use ufo handling on
later transformed packets") added a check that 'rt->dst.header_len' isn't
zero in order to skip UFO, but it doesn't include IPcomp in transport mode
where it equals zero.
Packets, after payload compression, may not require further fragmentation,
and if original length exceeds MTU, later compressed packets will be
transmitted incorrectly. This can be reproduced with LTP udp_ipsec.sh test
on veth device with enabled UFO, MTU is 1500 and UDP payload is 2000:
* IPv4 case, offset is wrong + unnecessary fragmentation
udp_ipsec.sh -p comp -m transport -s 2000 &
tcpdump -ni ltp_ns_veth2
...
IP (tos 0x0, ttl 64, id 45203, offset 0, flags [+],
proto Compressed IP (108), length 49)
10.0.0.2 > 10.0.0.1: IPComp(cpi=0x1000)
IP (tos 0x0, ttl 64, id 45203, offset 1480, flags [none],
proto UDP (17), length 21) 10.0.0.2 > 10.0.0.1: ip-proto-17
* IPv6 case, sending small fragments
udp_ipsec.sh -6 -p comp -m transport -s 2000 &
tcpdump -ni ltp_ns_veth2
...
IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
payload length: 37) fd00::2 > fd00::1: IPComp(cpi=0x1000)
IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
payload length: 21) fd00::2 > fd00::1: IPComp(cpi=0x1000)
Fix it by checking 'rt->dst.xfrm' pointer to 'xfrm_state' struct, skip UFO
if xfrm is set. So the new check will include both cases: IPcomp and IPsec.
Fixes: c146066ab8 ("ipv4: Don't use ufo handling on later transformed packets")
Fixes: f89c56ce71 ("ipv6: Don't use ufo handling on later transformed packets")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ip6_dst_lookup_tail has acquired a dst and fails the IPv4-mapped
check, release the dst before returning an error.
Fixes: ec5e3b0a1d ("ipv6: Inhibit IPv4-mapped src address on the wire.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the dst->pending_confirm flag was removed, we do not
need anymore to provide dst arg to dst_neigh_output.
So, rename it to neigh_output as before commit 5110effee8
("net: Do delayed neigh confirmation.").
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new skbuff flag to allow protocols to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Add sock_confirm_neigh() helper to confirm the neighbour and
use it for IPv4, IPv6 and VRF before dst_neigh_output.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 will mark data that is smaller that mtu - headersize as
CHECKSUM_PARTIAL, but if the data will completely fill the mtu,
the packet checksum will be computed in software instead.
Extend the conditional to include the data that fills the mtu
as well.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5 ("tcp: fix mark propagation with fwmark_reflect enabled")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an inconsistent conditional judgement between __ip6_append_data
and ip6_finish_output functions, the variable length in __ip6_append_data
just include the length of application's payload and udp6 header, don't
include the length of ipv6 header, but in ip6_finish_output use
(skb->len > ip6_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ipv6 header.
That causes some particular application's udp6 payloads whose length are
between (MTU - IPv6 Header) and MTU were fragmented by ip6_fragment even
though the rst->dev support UFO feature.
Add the length of ipv6 header to length in __ip6_append_data to keep
consistent conditional judgement as ip6_finish_output for ip6 fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from ip_output(), ip6_output() and
ip_mc_output(). From mentioned functions we have two socket contexts
as per 7026b1ddb6 ("netfilter: Pass socket pointer down through
okfn()."). We explicitly need to use sk instead of skb->sk here,
since otherwise the same program would run multiple times on egress
when encap devices are involved, which is not desired in our case.
eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).
Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) cast to "int" is unnecessary:
u8 will be promoted to int before decrementing,
small positive numbers fit into "int", so their values won't be changed
during promotion.
Once everything is int including loop counters, signedness doesn't
matter: 32-bit operations will stay 32-bit operations.
But! Someone tried to make this loop smart by making everything of
the same type apparently in an attempt to optimise it.
Do the optimization, just differently.
Do the cast where it matters. :^)
2) frag size is unsigned entity and sum of fragments sizes is also
unsigned.
Make everything unsigned, leave no MOVSX instruction behind.
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-4 (-4)
function old new delta
skb_cow_data 835 834 -1
ip_do_fragment 2549 2548 -1
ip6_fragment 3130 3128 -2
Total: Before=154865032, After=154865028, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for insertion of SRH through setsockopt().
The new source address argument is used when an HMAC field is
present in the SRH, which must be filled. The HMAC signature
process requires the source address as input text.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit c146066ab8 ("ipv4: Don't use ufo handling on later
transformed packets"), don't perform UFO on packets that will be IPsec
transformed. To detect it we rely on the fact that headerlen in
dst_entry is non-zero only for transformation bundles (xfrm_dst
objects).
Unwanted segmentation can be observed with a NETIF_F_UFO capable device,
such as a dummy device:
DEV=dum0 LEN=1493
ip li add $DEV type dummy
ip addr add fc00::1/64 dev $DEV nodad
ip link set $DEV up
ip xfrm policy add dir out src fc00::1 dst fc00::2 \
tmpl src fc00::1 dst fc00::2 proto esp spi 1
ip xfrm state add src fc00::1 dst fc00::2 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
tcpdump -n -nn -i $DEV -t &
socat /dev/zero,readbytes=$LEN udp6:[fc00::2]:$LEN
tcpdump output before:
IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448
IP6 fc00::1 > fc00::2: frag (1448|48)
IP6 fc00::1 > fc00::2: ESP(spi=0x00000001,seq=0x2), length 88
... and after:
IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448
IP6 fc00::1 > fc00::2: frag (1448|80)
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch added l3mdev flow update making these hooks
redundant. Remove them.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the infrastructure to the output path to pass an skb
to an l3mdev device if it has a hook registered. This is the Tx parallel
to l3mdev_ip{6}_rcv in the receive path and is the basis for removing
the existing hook that returns the vrf dst on the fib lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.
To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)
This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.
This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 source address selection needs to consider the real egress route.
Similar to IPv4 implement a get_saddr6 method which is called if
source address has not been set. The get_saddr6 method does a full
lookup which means pulling a route from the VRF FIB table and properly
considering linklocal/multicast destination addresses. Lookup failures
(eg., unreachable) then cause the source address selection to fail
which gets propagated back to the caller.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
At present we perform an xfrm_lookup() for each UDPv6 message we
send. The lookup involves querying the flow cache (flow_cache_lookup)
and, in case of a cache miss, creating an XFRM bundle.
If we miss the flow cache, we can end up creating a new bundle and
deriving the path MTU (xfrm_init_pmtu) from on an already transformed
dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down
to xfrm_lookup(). This can happen only if we're caching the dst_entry
in the socket, that is when we're using a connected UDP socket.
To put it another way, the path MTU shrinks each time we miss the flow
cache, which later on leads to incorrectly fragmented payload. It can
be observed with ESPv6 in transport mode:
1) Set up a transformation and lower the MTU to trigger fragmentation
# ip xfrm policy add dir out src ::1 dst ::1 \
tmpl src ::1 dst ::1 proto esp spi 1
# ip xfrm state add src ::1 dst ::1 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
# ip link set dev lo mtu 1500
2) Monitor the packet flow and set up an UDP sink
# tcpdump -ni lo -ttt &
# socat udp6-listen:12345,fork /dev/null &
3) Send a datagram that needs fragmentation with a connected socket
# perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345
2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error
00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448
00:00:00.000014 IP6 ::1 > ::1: frag (1448|32)
00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272
(^ ICMPv6 Parameter Problem)
00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136
4) Compare it to a non-connected socket
# perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345
00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448
00:00:00.000010 IP6 ::1 > ::1: frag (1448|64)
What happens in step (3) is:
1) when connecting the socket in __ip6_datagram_connect(), we
perform an XFRM lookup, miss the flow cache, create an XFRM
bundle, and cache the destination,
2) afterwards, when sending the datagram, we perform an XFRM lookup,
again, miss the flow cache (due to mismatch of flowi6_iif and
flowi6_oif, which is an issue of its own), and recreate an XFRM
bundle based on the cached (and already transformed) destination.
To prevent the recreation of an XFRM bundle, avoid an XFRM lookup
altogether whenever we already have a destination entry cached in the
socket. This prevents the path MTU shrinkage and brings us on par with
UDPv4.
The fix also benefits connected PINGv6 sockets, another user of
ip6_sk_dst_lookup_flow(), who also suffer messages being transformed
twice.
Joint work with Hannes Frederic Sowa.
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_network_seglen is not enough for checking fragment sizes if
skb is using GSO_BY_FRAGS as we have to check frag per frag.
This patch introduces skb_gso_validate_mtu, based on the former, which
will wrap the use case inside it as all calls to skb_gso_network_seglen
were to validate if it fits on a given TMU, and improve the check.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the sendmsg function of UDP, raw, ICMP and l2tp sockets, we use local
variables like hlimits, tclass, opt and dontfrag and pass them to corresponding
functions like ip6_make_skb, ip6_append_data and xxx_push_pending_frames.
This is not a good practice and makes it hard to add new parameters.
This fix introduces a new struct ipcm6_cookie similar to ipcm_cookie in
ipv4 and include the above mentioned variables. And we only pass the
pointer to this structure to corresponding functions. This makes it easier
to add new parameters in the future and makes the function cleaner.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP6_INC_STATS_BH() to __IP6_INC_STATS()
and IP6_ADD_STATS_BH() to __IP6_ADD_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a UDPv6 message longer than MTU, account for the length
of fragmentable IPv6 extension headers in skb->network_header offset.
Same as we do in alloc_new_skb path in __ip6_append_data().
This ensures that later on __ip6_make_skb() will make space in
headroom for fragmentable extension headers:
/* move skb->data to ip header from ext header */
if (skb->data < skb_network_header(skb))
__skb_pull(skb, skb_network_offset(skb));
Prevents a splat due to skb_under_panic:
skbuff: skb_under_panic: text:ffffffff8143397b len:2126 put:14 \
head:ffff880005bacf50 data:ffff880005bacf4a tail:0x48 end:0xc0 dev:lo
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] KASAN
CPU: 0 PID: 160 Comm: reproducer Not tainted 4.6.0-rc2 #65
[...]
Call Trace:
[<ffffffff813eb7b9>] skb_push+0x79/0x80
[<ffffffff8143397b>] eth_header+0x2b/0x100
[<ffffffff8141e0d0>] neigh_resolve_output+0x210/0x310
[<ffffffff814eab77>] ip6_finish_output2+0x4a7/0x7c0
[<ffffffff814efe3a>] ip6_output+0x16a/0x280
[<ffffffff815440c1>] ip6_local_out+0xb1/0xf0
[<ffffffff814f1115>] ip6_send_skb+0x45/0xd0
[<ffffffff81518836>] udp_v6_send_skb+0x246/0x5d0
[<ffffffff8151985e>] udpv6_sendmsg+0xa6e/0x1090
[...]
Reported-by: Ji Jianwen <jiji@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.
Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.
Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 52bd2d62ce ("net: better skb->sender_cpu and skb->napi_id cohabitation")
skb_sender_cpu_clear() becomes empty and can be removed.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of ip6_dst_lookup_tail basically
ignore the egress ifindex match: if the saddr is set,
ip6_route_output() purposefully ignores flowi6_oif, due
to the commit d46a9d678e ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE
flag if saddr set"), if the saddr is 'any' the first route lookup
in ip6_dst_lookup_tail fails, but upon failure a second lookup will
be performed with saddr set, thus ignoring the ifindex constraint.
This commit adds an output route lookup function variant, which
allows the caller to specify lookup flags, and modify
ip6_dst_lookup_tail() to enforce the ifindex match on the second
lookup via said helper.
ip6_route_output() becames now a static inline function build on
top of ip6_route_output_flags(); as a side effect, out-of-tree
modules need now a GPL license to access the output route lookup
functionality.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit acf8dd0a9d ("udp: only allow UFO for packets from SOCK_DGRAM
sockets") disallows UFO for packets sent from raw sockets. We need to do
the same also for SOCK_DGRAM sockets with SO_NO_CHECK options, even if
for a bit different reason: while such socket would override the
CHECKSUM_PARTIAL set by ip_ufo_append_data(), gso_size is still set and
bad offloading flags warning is triggered in __skb_gso_segment().
In the IPv6 case, SO_NO_CHECK option is ignored but we need to disallow
UFO for packets sent by sockets with UDP_NO_CHECK6_TX option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Tested-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These netif flags are unnecessary convolutions. It is more
straightforward to just use NETIF_F_HW_CSUM, NETIF_F_IP_CSUM,
and NETIF_F_IPV6_CSUM directly.
This patch also:
- Cleans up can_checksum_protocol
- Simplifies netdev_intersect_features
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHECKSUM_PARTIAL skbs should never arrive in ip_fragment. If we get one
of those warn about them once and handle them gracefully by recalculating
the checksum.
Fixes: commit 32dce968dd ("ipv6: Allow for partial checksums on non-ufo packets")
See-also: commit 72e843bb09 ("ipv6: ip6_fragment() should check CHECKSUM_PARTIAL")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Benjamin Coddington <bcodding@redhat.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot reliable calculate packet size on MSG_MORE corked sockets
and thus cannot decide if they are going to be fragmented later on,
so better not use CHECKSUM_PARTIAL in the first place.
The IPv6 code also intended to protect and not use CHECKSUM_PARTIAL in
the existence of IPv6 extension headers, but the condition was wrong. Fix
it up, too. Also the condition to check whether the packet fits into
one fragment was wrong and has been corrected.
Fixes: commit 32dce968dd ("ipv6: Allow for partial checksums on non-ufo packets")
See-also: commit 72e843bb09 ("ipv6: ip6_fragment() should check CHECKSUM_PARTIAL")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Benjamin Coddington <bcodding@redhat.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raw sockets with hdrincl enabled can insert ipv6 extension headers
right into the data stream. In case we need to fragment those packets,
we reparse the options header to find the place where we can insert
the fragment header. If the extension headers exceed the link's MTU we
actually cannot make progress in such a case.
Instead of ending up in broken arithmetic or rounding towards 0 and
entering an endless loop in ip6_fragment, just prevent those cases by
aborting early and signal -EMSGSIZE to user space.
This is the second version of the patch which doesn't use the
overflow_usub function, which got reverted for now.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus dislikes these changes. To not hold up the net-merge let's revert
it for now and fix the bug like Linus suggested.
This reverts commit ec3661b422, reversing
changes made to c80dbe0461.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Raw sockets with hdrincl enabled can insert ipv6 extension headers
right into the data stream. In case we need to fragment those packets,
we reparse the options header to find the place where we can insert
the fragment header. If the extension headers exceed the link's MTU we
actually cannot make progress in such a case.
Instead of ending up in broken arithmetic or rounding towards 0 and
entering an endless loop in ip6_fragment, just prevent those cases by
aborting early and signal -EMSGSIZE to user space.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
6e28b00082 ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.
Fixes: 42a7b32b73 ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As with IPv4 support for VRFs added to IPv6 stack by replacing hardcoded
table ids with possibly device specific ones and manipulating the oif in
the flowi6. The flow flags are used to skip oif compare in nexthop lookups
if the device is enslaved to a VRF via the L3 master device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a clone of commit 2ab957492d ("ip_forward: Drop frames with
attached skb->sk") for ipv6.
This commit has exactly the same reasons as the above mentioned commit,
namely to prevent panics during netfilter reload or a misconfigured stack.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network namespace is already passed into dst_output pass it into
dst->output lwt->output and friends.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop hidding the sk parameter with an inline helper function and make
all of the callers pass it, so that it is clear what the function is
doing.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dst_output_okfn with dst_output
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to document that socket lock might not be held at this point.
skb_set_owner_w() and ipv6_local_error() are using proper atomic ops
or spinlocks, so we promote the socket to non const when calling them.
netfilter hooks should never assume socket lock is held,
we also promote the socket to non const.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_dst_lookup_flow() and ip6_dst_lookup_tail() do not touch
socket, lets add a const qualifier.
This will permit the same change in inet6_csk_route_req()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse reports skb_under_panic when we try to push ethernet
header to fragmented ipv6 skbs:
skbuff: skb_under_panic: text:c1277f1e len:1294 put:14 head:dec98000
data:dec97ffc tail:0xdec9850a end:0xdec98f40 dev:br-lan
[..]
ip6_finish_output2+0x196/0x4da
David further debugged this:
[..] offending fragments were arriving here with skb_headroom(skb)==10.
Which is reasonable, being the Solos ADSL card's header of 8 bytes
followed by 2 bytes of PPP frame type.
The problem is that if netfilter ipv6 defragmentation is used, skb_cow()
in ip6_forward will only see reassembled skb.
Therefore, headroom is overestimated by 8 bytes (we pulled fragment
header) and we don't check the skbs in the frag_list either.
We can't do these checks in netfilter defrag since outdev isn't known yet.
Furthermore, existing tests in ip6_fragment did not consider the fragment
or ipv6 header size when checking headroom of the fraglist skbs.
While at it, also fix a skb leak on memory allocation -- ip6_fragment
must consume the skb.
I tested this e1000 driver hacked to not allocate additional headroom
(we end up in slowpath, since LL_RESERVED_SPACE is 16).
If 2 bytes of headroom are allocated, fastpath is taken (14 byte
ethernet header was pulled, so 16 byte headroom available in all
fragments).
Reported-by: David Woodhouse <dwmw2@infradead.org>
Diagnosed-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In code review it was noticed that I had failed to add some blank lines
in places where they are customarily used. Taking a second look at the
code I have to agree blank lines would be nice so I have added them
here.
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
