rpcrdma_bc_post_recv() is never implemented since introduction in
commit f531a5dbc4 ("xprtrdma: Pre-allocate backward rpc_rqst and send/receive buffers").
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xprtrdma always drives a retry of MR allocation if it should fail.
It should be safe to not use GFP_KERNEL for this purpose rather
than sleeping in the memory allocator.
In theory, if these weaker allocations are attempted first, memory
exhaustion is likely to cause xprtrdma to fail fast and not then
invoke the RDMA core APIs, which still might use GFP_KERNEL.
Also note that rpc_task_gfp_mask() always sets __GFP_NORETRY and
__GFP_NOWARN when an RPC-related allocation is being done in a
worker thread. MR allocation is already always done in worker
threads.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Commit 1769e6a816 ("xprtrdma: Clean up rpcrdma_create_req()")
added rpcrdma_req_create() with a GFP flags argument in case a
caller might want to avoid waiting for memory.
There has never been a caller that does not pass GFP_KERNEL as
the third argument. That argument can therefore be eliminated.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xprt_rdma_bc_allocate() is now the only user of RPCRDMA_DEF_GFP.
Replace that macro with the raw flags.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: this field is no longer used.
xprt_rdma_pad_optimize is also no longer used, but is left in place
because it is part of the kernel/userspace API.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This is a buffer to be left persistently registered while a
connection is up. Connection tear-down will automatically DMA-unmap,
invalidate, and dereg the MR. A persistently registered buffer is
lower in cost to provide, and it can never be coalesced into the
RDMA segment that carries the data payload.
An RPC that provisions a Write chunk with a non-aligned length now
uses this MR rather than the tail buffer of the RPC's rq_rcv_buf.
Reviewed-By: Tom Talpey <tom@talpey.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clean up.
Now that there is only one registration mode, there is only one
target "post_send" method: frwr_send(). rpcrdma_post_sends() no
longer adds much value, especially since all of its call sites
ignore the return code value except to check if it's non-zero.
Just have them call frwr_send() directly instead.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
ib_post_send() does not disconnect the QP when it returns an
immediate error. Thus, the code that posts LocalInv has to
explicitly disconnect after an immediate error. This is just
like the frwr_send() callers handle it.
If a disconnect isn't done here, the transport deadlocks.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Ensure that we fix the XPRT_CONGESTED starvation issue for RDMA as well
as socket based transports.
Ensure we always initialise the request after waking up from the backlog
list.
Fixes: e877a88d1f ("SUNRPC in case of backlog, hand free slots directly to waiting task")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clean up: The last remaining field in struct rpcrdma_frwr has been
removed, so the struct can be eliminated.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clean up: Move more of struct rpcrdma_frwr into its parent.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clean up.
- Simplify variable initialization in the completion handlers.
- Move another field out of struct rpcrdma_frwr.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clean up (for several purposes):
- The MR's cid is initialized sooner so that tracepoints can show
something reasonable even if the MR is never posted.
- The MR's res.id doesn't change so the cid won't change either.
Initializing the cid once is sufficient.
- struct rpcrdma_frwr is going away soon.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Throw away any reply where the LocalInv flushes or could not be
posted. The registered memory region is in an unknown state until
the disconnect completes.
rpcrdma_xprt_disconnect() will find and release the MR. No need to
put it back on the MR free list in this case.
The client retransmits pending RPC requests once it reestablishes a
fresh connection, so a replacement reply should be forthcoming on
the next connection instance.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clean up: To be consistent with other functions in this source file,
follow the naming convention of putting the object being acted upon
before the action itself.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clean up: The name recv_buffer_put() is a vestige of older code,
and the function is just a wrapper for the newer rpcrdma_rep_put().
In most of the existing call sites, a pointer to the owning
rpcrdma_buffer is already available.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
After a reconnect, the reply handler is opening the cwnd (and thus
enabling more RPC Calls to be sent) /before/ rpcrdma_post_recvs()
can post enough Receive WRs to receive their replies. This causes an
RNR and the new connection is lost immediately.
The race is most clearly exposed when KASAN and disconnect injection
are enabled. This slows down rpcrdma_rep_create() enough to allow
the send side to post a bunch of RPC Calls before the Receive
completion handler can invoke ib_post_recv().
Fixes: 2ae50ad68c ("xprtrdma: Close window between waking RPC senders and posting Receives")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Currently the Receive completion handler refreshes the Receive Queue
whenever a successful Receive completion occurs.
On disconnect, xprtrdma drains the Receive Queue. The first few
Receive completions after a disconnect are typically successful,
until the first flushed Receive.
This means the Receive completion handler continues to post more
Receive WRs after the drain sentinel has been posted. The late-
posted Receives flush after the drain sentinel has completed,
leading to a crash later in rpcrdma_xprt_disconnect().
To prevent this crash, xprtrdma has to ensure that the Receive
handler stops posting Receives before ib_drain_rq() posts its
drain sentinel.
Suggested-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
During the final stages of publication of RFC 8167, reviewers
requested that we use the term "reverse direction" rather than
"backwards direction". Update comments to reflect this preference.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up so that offset_in_page() is invoked less often in the
most common case, which is mapping xdr->pages.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up.
Remove a conditional branch from the SGL set-up loop in frwr_map():
Instead of using either sg_set_page() or sg_set_buf(), initialize
the mr_page field properly when rpcrdma_convert_kvec() converts the
kvec to an SGL entry. frwr_map() can then invoke sg_set_page()
unconditionally.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Now that rpcrdma_ep is no longer part of rpcrdma_xprt, there are
four or five serial address dereferences needed to get to the
IB device needed for DMA unmapping.
Instead, let's use the same pattern that regbufs use: cache a
pointer to the device in the MR, and use that as the indication
that unmapping is necessary.
This also guarantees that the exact same device is used for DMA
mapping and unmapping, even if the r_xprt's ep has been replaced. I
don't think this can happen today, but future changes might break
this assumption.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: This function is now invoked only in frwr_ops.c. The move
enables deduplication of the trace_xprtrdma_mr_unmap() call site.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Set up a completion ID in each rpcrdma_frwr. The ID is used to match
an incoming completion to a transport (CQ) and other MR-related
activity.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Set up a completion ID in each rpcrdma_req. The ID is used to match
an incoming Send completion to a transport and to a previous
ib_post_send().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Set up a completion ID in each rpcrdma_rep. The ID is used to match
an incoming Receive completion to a transport and to a previous
ib_post_recv().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
1. Ensure that only rpcrdma_cm_event_handler() modifies
ep->re_connect_status to avoid racy changes to that field.
2. Ensure that xprt_force_disconnect() is invoked only once as a
transport is closed or destroyed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Refactor: Pass struct rpcrdma_xprt instead of an IB layer object.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Change the rpcrdma_xprt_disconnect() function so that it no longer
waits for the DISCONNECTED event. This prevents blocking if the
remote is unresponsive.
In rpcrdma_xprt_disconnect(), the transport's rpcrdma_ep is
detached. Upon return from rpcrdma_xprt_disconnect(), the transport
(r_xprt) is ready immediately for a new connection.
The RDMA_CM_DEVICE_REMOVAL and RDMA_CM_DISCONNECTED events are now
handled almost identically.
However, because the lifetimes of rpcrdma_xprt structures and
rpcrdma_ep structures are now independent, creating an rpcrdma_ep
needs to take a module ref count. The ep now owns most of the
hardware resources for a transport.
Also, a kref is needed to ensure that rpcrdma_ep sticks around
long enough for the cm_event_handler to finish.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I eventually want to allocate rpcrdma_ep separately from struct
rpcrdma_xprt so that on occasion there can be more than one ep per
xprt.
The new struct rpcrdma_ep will contain all the fields currently in
rpcrdma_ia and in rpcrdma_ep. This is all the device and CM settings
for the connection, in addition to per-connection settings
negotiated with the remote.
Take this opportunity to rename the existing ep fields from rep_* to
re_* to disambiguate these from struct rpcrdma_rep.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Completion errors after a disconnect often occur much sooner than a
CM_DISCONNECT event. Use this to try to detect connection loss more
quickly.
Note that other kernel ULPs do take care to disconnect explicitly
when a WR is flushed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up:
The upper layer serializes calls to xprt_rdma_close, so there is no
need for an atomic bit operation, saving 8 bytes in rpcrdma_ia.
This enables merging rpcrdma_ia_remove directly into the disconnect
logic.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Move rdma_cm_id creation into rpcrdma_ep_create() so that it is now
responsible for allocating all per-connection hardware resources.
With this clean-up, all three arms of the switch statement in
rpcrdma_ep_connect are exactly the same now, thus the switch can be
removed.
Because device removal behaves a little differently than
disconnection, there is a little more work to be done before
rpcrdma_ep_destroy() can release the connection's rdma_cm_id. So
it is not quite symmetrical with rpcrdma_ep_create() yet.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Simplify the synopses of functions in the connect and
disconnect paths in preparation for combining the rpcrdma_ia and
struct rpcrdma_ep structures.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Simplify the synopses of functions in the post_send path
by combining the struct rpcrdma_ia and struct rpcrdma_ep arguments.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: prepare for combining the rpcrdma_ia and rpcrdma_ep
structures. Take the opportunity to rename the function to be
consistent with the "subsystem _ object _ verb" naming scheme.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Refactor rpcrdma_ep_create(), rpcrdma_ep_disconnect(), and
rpcrdma_ep_destroy().
rpcrdma_ep_create will be invoked at connect time instead of at
transport set-up time. It will be responsible for allocating per-
connection resources. In this patch it allocates the CQs and
creates a QP. More to come.
rpcrdma_ep_destroy() is the inverse functionality that is
invoked at disconnect time. It will be responsible for releasing
the CQs and QP.
These changes should be safe to do because both connect and
disconnect is guaranteed to be serialized by the transport send
lock.
This takes us another step closer to resolving the address and route
only at connect time so that connection failover to another device
will work correctly.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently the underlying RDMA device is chosen at transport set-up
time. But it will soon be at connect time instead.
The maximum size of a transport header is based on device
capabilities. Thus transport header buffers have to be allocated
_after_ the underlying device has been chosen (via address and route
resolution); ie, in the connect worker.
Thus, move the allocation of transport header buffers to the connect
worker, after the point at which the underlying RDMA device has been
chosen.
This also means the RDMA device is available to do a DMA mapping of
these buffers at connect time, instead of in the hot I/O path. Make
that optimization as well.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Refactor: Perform the "is supported" check in rpcrdma_ep_create()
instead of in rpcrdma_ia_open(). frwr_open() is where most of the
logic to query device attributes is already located.
The current code displays a redundant error message when the device
does not support FRWR. As an additional clean-up, this patch removes
the extra message.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
To support device hotplug and migrating a connection between devices
of different capabilities, we have to guarantee that all in-kernel
devices can support the same max NFS payload size (1 megabyte).
This means that possibly one or two in-tree devices are no longer
supported for NFS/RDMA because they cannot support 1MB rsize/wsize.
The only one I confirmed was cxgb3, but it has already been removed
from the kernel.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: there is no need to keep two copies of the same value.
Also, in subsequent patches, rpcrdma_ep_create() will be called in
the connect worker rather than at set-up time.
Minor fix: Initialize the transport's sendctx to the value based on
the capabilities of the underlying device, not the maximum setting.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean-up. The max_send_sge value also happens to be stored in
ep->rep_attr. Let's keep just a single copy.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Since v5.4, a device removal occasionally triggered this oops:
Dec 2 17:13:53 manet kernel: BUG: unable to handle page fault for address: 0000000c00000219
Dec 2 17:13:53 manet kernel: #PF: supervisor read access in kernel mode
Dec 2 17:13:53 manet kernel: #PF: error_code(0x0000) - not-present page
Dec 2 17:13:53 manet kernel: PGD 0 P4D 0
Dec 2 17:13:53 manet kernel: Oops: 0000 [#1] SMP
Dec 2 17:13:53 manet kernel: CPU: 2 PID: 468 Comm: kworker/2:1H Tainted: G W 5.4.0-00050-g53717e43af61 #883
Dec 2 17:13:53 manet kernel: Hardware name: Supermicro SYS-6028R-T/X10DRi, BIOS 1.1a 10/16/2015
Dec 2 17:13:53 manet kernel: Workqueue: ib-comp-wq ib_cq_poll_work [ib_core]
Dec 2 17:13:53 manet kernel: RIP: 0010:rpcrdma_wc_receive+0x7c/0xf6 [rpcrdma]
Dec 2 17:13:53 manet kernel: Code: 6d 8b 43 14 89 c1 89 45 78 48 89 4d 40 8b 43 2c 89 45 14 8b 43 20 89 45 18 48 8b 45 20 8b 53 14 48 8b 30 48 8b 40 10 48 8b 38 <48> 8b 87 18 02 00 00 48 85 c0 75 18 48 8b 05 1e 24 c4 e1 48 85 c0
Dec 2 17:13:53 manet kernel: RSP: 0018:ffffc900035dfe00 EFLAGS: 00010246
Dec 2 17:13:53 manet kernel: RAX: ffff888467290000 RBX: ffff88846c638400 RCX: 0000000000000048
Dec 2 17:13:53 manet kernel: RDX: 0000000000000048 RSI: 00000000f942e000 RDI: 0000000c00000001
Dec 2 17:13:53 manet kernel: RBP: ffff888467611b00 R08: ffff888464e4a3c4 R09: 0000000000000000
Dec 2 17:13:53 manet kernel: R10: ffffc900035dfc88 R11: fefefefefefefeff R12: ffff888865af4428
Dec 2 17:13:53 manet kernel: R13: ffff888466023000 R14: ffff88846c63f000 R15: 0000000000000010
Dec 2 17:13:53 manet kernel: FS: 0000000000000000(0000) GS:ffff88846fa80000(0000) knlGS:0000000000000000
Dec 2 17:13:53 manet kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Dec 2 17:13:53 manet kernel: CR2: 0000000c00000219 CR3: 0000000002009002 CR4: 00000000001606e0
Dec 2 17:13:53 manet kernel: Call Trace:
Dec 2 17:13:53 manet kernel: __ib_process_cq+0x5c/0x14e [ib_core]
Dec 2 17:13:53 manet kernel: ib_cq_poll_work+0x26/0x70 [ib_core]
Dec 2 17:13:53 manet kernel: process_one_work+0x19d/0x2cd
Dec 2 17:13:53 manet kernel: ? cancel_delayed_work_sync+0xf/0xf
Dec 2 17:13:53 manet kernel: worker_thread+0x1a6/0x25a
Dec 2 17:13:53 manet kernel: ? cancel_delayed_work_sync+0xf/0xf
Dec 2 17:13:53 manet kernel: kthread+0xf4/0xf9
Dec 2 17:13:53 manet kernel: ? kthread_queue_delayed_work+0x74/0x74
Dec 2 17:13:53 manet kernel: ret_from_fork+0x24/0x30
The proximal cause is that this rpcrdma_rep has a rr_rdmabuf that
is still pointing to the old ib_device, which has been freed. The
only way that is possible is if this rpcrdma_rep was not destroyed
by rpcrdma_ia_remove.
Debugging showed that was indeed the case: this rpcrdma_rep was
still in use by a completing RPC at the time of the device removal,
and thus wasn't on the rep free list. So, it was not found by
rpcrdma_reps_destroy().
The fix is to introduce a list of all rpcrdma_reps so that they all
can be found when a device is removed. That list is used to perform
only regbuf DMA unmapping, replacing that call to
rpcrdma_reps_destroy().
Meanwhile, to prevent corruption of this list, I've moved the
destruction of temp rpcrdma_rep objects to rpcrdma_post_recvs().
rpcrdma_xprt_drain() ensures that post_recvs (and thus rep_destroy) is
not invoked while rpcrdma_reps_unmap is walking rb_all_reps, thus
protecting the rb_all_reps list.
Fixes: b0b227f071 ("xprtrdma: Use an llist to manage free rpcrdma_reps")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
On some platforms, DMA mapping part of a page is more costly than
copying bytes. Restore the pull-up code and use that when we
think it's going to be faster. The heuristic for now is to pull-up
when the size of the RPC message body fits in the buffer underlying
the head iovec.
Indeed, not involving the I/O MMU can help the RPC/RDMA transport
scale better for tiny I/Os across more RDMA devices. This is because
interaction with the I/O MMU is eliminated, as is handling a Send
completion, for each of these small I/Os. Without the explicit
unmapping, the NIC no longer needs to do a costly internal TLB shoot
down for buffers that are just a handful of bytes.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: This field is not needed in the Send completion handler,
so it can be moved to struct rpcrdma_req to reduce the size of
struct rpcrdma_sendctx, and to reduce the amount of memory that
is sloshed between the sending process and the Send completion
process.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Micro-optimization: Save eight bytes in a frequently allocated
structure.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Micro-optimization: Save eight bytes in a frequently allocated
structure.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
ia->ri_id is replaced during a reconnect. The connect_worker runs
with the transport send lock held to prevent ri_id from being
dereferenced by the send_request path during this process.
Currently, however, there is no guarantee that ia->ri_id is stable
in the MR recycling worker, which operates in the background and is
not serialized with the connect_worker in any way.
But now that Local_Inv completions are being done in process
context, we can handle the recycling operation there instead of
deferring the recycling work to another process. Because the
disconnect path drains all work before allowing tear down to
proceed, it is guaranteed that Local Invalidations complete only
while the ri_id pointer is stable.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
MRs are now allocated on demand so we can safely throw them away on
disconnect. This way an idle transport can disconnect and it won't
pin hardware MR resources.
Two additional changes:
- Now that all MRs are destroyed on disconnect, there's no need to
check during header marshaling if a req has MRs to recycle. Each
req is sent only once per connection, and now rl_registered is
guaranteed to be empty when rpcrdma_marshal_req is invoked.
- Because MRs are now destroyed in a WQ_MEM_RECLAIM context, they
also must be allocated in a WQ_MEM_RECLAIM context. This reduces
the likelihood that device driver memory allocation will trigger
memory reclaim during NFS writeback.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Yue Haibing