The mcp251x driver uses both receiving mailboxes of the CAN controller
chips. For retrieving the CAN frames from the controller via SPI, it checks
once per interrupt which mailboxes have been filled and will retrieve the
messages accordingly.
This introduces a race condition, as another CAN frame can enter mailbox 1
while mailbox 0 is emptied. If now another CAN frame enters mailbox 0 until
the interrupt handler is called next, mailbox 0 is emptied before
mailbox 1, leading to out-of-order CAN frames in the network device.
This is fixed by checking the interrupt flags once again after freeing
mailbox 0, to correctly also empty mailbox 1 before leaving the handler.
For reproducing the bug I created the following setup:
- Two CAN devices, one Raspberry Pi with MCP2515, the other can be any.
- Setup CAN to 1 MHz
- Spam bursts of 5 CAN-messages with increasing CAN-ids
- Continue sending the bursts while sleeping a second between the bursts
- Check on the RPi whether the received messages have increasing CAN-ids
- Without this patch, every burst of messages will contain a flipped pair
v3: https://lore.kernel.org/all/20220804075914.67569-1-sebastian.wuerl@ororatech.com
v2: https://lore.kernel.org/all/20220804064803.63157-1-sebastian.wuerl@ororatech.com
v1: https://lore.kernel.org/all/20220803153300.58732-1-sebastian.wuerl@ororatech.com
Fixes: bf66f3736a ("can: mcp251x: Move to threaded interrupts instead of workqueues.")
Signed-off-by: Sebastian Würl <sebastian.wuerl@ororatech.com>
Link: https://lore.kernel.org/all/20220804081411.68567-1-sebastian.wuerl@ororatech.com
[mkl: reduce scope of intf1, eflag1]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
WARNING: suspicious RCU usage
5.2.0-rc2-00605-g2638eb8b50cfc #1 Not tainted
drivers/net/plip/plip.c:1110 suspicious rcu_dereference_check() usage!
plip_open is called with RTNL held, switch to the correct helper.
Fixes: 2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20220807115304.13257-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The way in which dsa_tree_change_tag_proto() works is that when
dsa_tree_notify() fails, it doesn't know whether the operation failed
mid way in a multi-switch tree, or it failed for a single-switch tree.
So even though drivers need to fail cleanly in
ds->ops->change_tag_protocol(), DSA will still call dsa_tree_notify()
again, to restore the old tag protocol for potential switches in the
tree where the change did succeeed (before failing for others).
This means for the felix driver that if we report an error in
felix_change_tag_protocol(), we'll get another call where proto_ops ==
old_proto_ops. If we proceed to act upon that, we may do unexpected
things. For example, we will call dsa_tag_8021q_register() twice in a
row, without any dsa_tag_8021q_unregister() in between. Then we will
actually call dsa_tag_8021q_unregister() via old_proto_ops->teardown,
which (if it manages to run at all, after walking through corrupted data
structures) will leave the ports inoperational anyway.
The bug can be readily reproduced if we force an error while in
tag_8021q mode; this crashes the kernel.
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
echo edsa > /sys/class/net/eno2/dsa/tagging # -EPROTONOSUPPORT
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014
Call trace:
vcap_entry_get+0x24/0x124
ocelot_vcap_filter_del+0x198/0x270
felix_tag_8021q_vlan_del+0xd4/0x21c
dsa_switch_tag_8021q_vlan_del+0x168/0x2cc
dsa_switch_event+0x68/0x1170
dsa_tree_notify+0x14/0x34
dsa_port_tag_8021q_vlan_del+0x84/0x110
dsa_tag_8021q_unregister+0x15c/0x1c0
felix_tag_8021q_teardown+0x16c/0x180
felix_change_tag_protocol+0x1bc/0x230
dsa_switch_event+0x14c/0x1170
dsa_tree_change_tag_proto+0x118/0x1c0
Fixes: 7a29d220f4 ("net: dsa: felix: reimplement tagging protocol change with function pointers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220808125127.3344094-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
First set of fixes for v6.0. Small one this time, fix a cfg80211
warning seen with brcmfmac and remove an unncessary inline keyword
from wilc1000.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmLyj2ERHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtxaggAptzh9NVi2qCWpCdwIjp+d6CusPoEA4NN
eI7PSLecWPA5MVCR5YXSOboVDEtV/wGDOk/N1fKpKVXW02+7nvuLohx5tOclFpms
CZtS2thpyEvUW6Zu+bE1Opwyx1v4e3nyznrNXMHW8tcnaVI3BNwYpdp7LRCylv07
JQPNKZvxR5fs8NuIhf0O1TSjPaUSvRrMWfRn3ZioHWVa7+j8qMfnxWk+o6n38zP5
fqbYlhLEBS3Nu9jp3e26KRMRrkAs/OTb/oRc/bPbU68V0VFPquP97Fz0vOobyjzO
+B5+qAcaNpP6lSlAmrVyPxFEO1Y0utXblXblrWQsAqox7rt/PXQecg==
=2QwM
-----END PGP SIGNATURE-----
Merge tag 'wireless-2022-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.0
First set of fixes for v6.0. Small one this time, fix a cfg80211
warning seen with brcmfmac and remove an unncessary inline keyword
from wilc1000.
* tag 'wireless-2022-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: wilc1000: fix spurious inline in wilc_handle_disconnect()
wifi: cfg80211: Fix validating BSS pointers in __cfg80211_connect_result
====================
Link: https://lore.kernel.org/r/20220809164756.B1DAEC433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In nf_tables_updtable, if nf_tables_table_enable returns an error,
nft_trans_destroy is called to free the transaction object.
nft_trans_destroy() calls list_del(), but the transaction was never
placed on a list -- the list head is all zeroes, this results in
a null dereference:
BUG: KASAN: null-ptr-deref in nft_trans_destroy+0x26/0x59
Call Trace:
nft_trans_destroy+0x26/0x59
nf_tables_newtable+0x4bc/0x9bc
[..]
Its sane to assume that nft_trans_destroy() can be called
on the transaction object returned by nft_trans_alloc(), so
make sure the list head is initialised.
Fixes: 55dd6f9307 ("netfilter: nf_tables: use new transaction infrastructure to handle table")
Reported-by: mingi cho <mgcho.minic@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Extend struct nft_data_desc to add a flag field that specifies
nft_data_init() is being called for set element data.
Use it to disallow jump to implicit chain from set element, only jump
to chain via immediate expression is allowed.
Fixes: d0e2c7de92 ("netfilter: nf_tables: add NFT_CHAIN_BINDING")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of parsing the data and then validate that type and length are
correct, pass a description of the expected data so it can be validated
upfront before parsing it to bail out earlier.
This patch adds a new .size field to specify the maximum size of the
data area. The .len field is optional and it is used as an input/output
field, it provides the specific length of the expected data in the input
path. If then .len field is not specified, then obtained length from the
netlink attribute is stored. This is required by cmp, bitwise, range and
immediate, which provide no netlink attribute that describes the data
length. The immediate expression uses the destination register type to
infer the expected data type.
Relying on opencoded validation of the expected data might lead to
subtle bugs as described in 7e6bc1f6ca ("netfilter: nf_tables:
stricter validation of element data").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
s/_IPT_LOG_H/_IP6T_LOG_H/
While at it add some surrounding space to ease reading.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When doing lookups for rules on the same batch by using its ID, a rule from
a different chain can be used. If a rule is added to a chain but tries to
be positioned next to a rule from a different chain, it will be linked to
chain2, but the use counter on chain1 would be the one to be incremented.
When looking for rules by ID, use the chain that was used for the lookup by
name. The chain used in the context copied to the transaction needs to
match that same chain. That way, struct nft_rule does not need to get
enlarged with another member.
Fixes: 1a94e38d25 ("netfilter: nf_tables: add NFTA_RULE_ID attribute")
Fixes: 75dd48e2e4 ("netfilter: nf_tables: Support RULE_ID reference in new rule")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When doing lookups for chains on the same batch by using its ID, a chain
from a different table can be used. If a rule is added to a table but
refers to a chain in a different table, it will be linked to the chain in
table2, but would have expressions referring to objects in table1.
Then, when table1 is removed, the rule will not be removed as its linked to
a chain in table2. When expressions in the rule are processed or removed,
that will lead to a use-after-free.
When looking for chains by ID, use the table that was used for the lookup
by name, and only return chains belonging to that same table.
Fixes: 837830a4b4 ("netfilter: nf_tables: add NFTA_RULE_CHAIN_ID attribute")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When doing lookups for sets on the same batch by using its ID, a set from a
different table can be used.
Then, when the table is removed, a reference to the set may be kept after
the set is freed, leading to a potential use-after-free.
When looking for sets by ID, use the table that was used for the lookup by
name, and only return sets belonging to that same table.
This fixes CVE-2022-2586, also reported as ZDI-CAN-17470.
Reported-by: Team Orca of Sea Security (@seasecresponse)
Fixes: 958bee14d0 ("netfilter: nf_tables: use new transaction infrastructure to handle sets")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Update template to validate variable length extensions. This patch adds
a new .ext_len[id] field to the template to store the expected extension
length. This is used to sanity check the initialization of the variable
length extension.
Use PTR_ERR() in nft_set_elem_init() to report errors since, after this
update, there are two reason why this might fail, either because of
ENOMEM or insufficient room in the extension field (EINVAL).
Kernels up until 7e6bc1f6ca ("netfilter: nf_tables: stricter
validation of element data") allowed to copy more data to the extension
than was allocated. This ext_len field allows to validate if the
destination has the correct size as additional check.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
clang emits a -Wunaligned-access warning on struct __packed
ems_cpc_msg.
The reason is that the anonymous union msg (not declared as packed) is
being packed right after some non naturally aligned variables (3*8
bits + 2*32) inside a packed struct:
| struct __packed ems_cpc_msg {
| u8 type; /* type of message */
| u8 length; /* length of data within union 'msg' */
| u8 msgid; /* confirmation handle */
| __le32 ts_sec; /* timestamp in seconds */
| __le32 ts_nsec; /* timestamp in nano seconds */
| /* ^ not naturally aligned */
|
| union {
| /* ^ not declared as packed */
| u8 generic[64];
| struct cpc_can_msg can_msg;
| struct cpc_can_params can_params;
| struct cpc_confirm confirmation;
| struct cpc_overrun overrun;
| struct cpc_can_error error;
| struct cpc_can_err_counter err_counter;
| u8 can_state;
| } msg;
| };
Starting from LLVM 14, having an unpacked struct nested in a packed
struct triggers a warning. c.f. [1].
Fix the warning by marking the anonymous union as packed.
[1] https://github.com/llvm/llvm-project/issues/55520
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/all/20220802094021.959858-1-mkl@pengutronix.de
Cc: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We need to drop skb references taken in j1939_session_skb_queue() when
destroying a session in j1939_session_destroy(). Otherwise those skbs
would be lost.
Link to Syzkaller info and repro: https://forge.ispras.ru/issues/11743.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
V1: https://lore.kernel.org/all/20220708175949.539064-1-pchelkin@ispras.ru
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20220805150216.66313-1-pchelkin@ispras.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We should warn user-space that it is doing something wrong when trying
to activate sessions with identical parameters but WARN_ON_ONCE macro
can not be used here as it serves a different purpose.
So it would be good to replace it with netdev_warn_once() message.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20220729143655.1108297-1-pchelkin@ispras.ru
[mkl: fix indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- Fixes various issues related to ISO channel/socket support
- Fixes issues when building with C=1
- Fix cancel uninitilized work which blocks syzbot to run
-----BEGIN PGP SIGNATURE-----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=nFPi
-----END PGP SIGNATURE-----
Merge tag 'for-net-2022-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fixes various issues related to ISO channel/socket support
- Fixes issues when building with C=1
- Fix cancel uninitilized work which blocks syzbot to run
* tag 'for-net-2022-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: ISO: Fix not using the correct QoS
Bluetooth: don't try to cancel uninitialized works at mgmt_index_removed()
Bluetooth: ISO: Fix iso_sock_getsockopt for BT_DEFER_SETUP
Bluetooth: MGMT: Fixes build warnings with C=1
Bluetooth: hci_event: Fix build warning with C=1
Bluetooth: ISO: Fix memory corruption
Bluetooth: Fix null pointer deref on unexpected status event
Bluetooth: ISO: Fix info leak in iso_sock_getsockopt()
Bluetooth: hci_conn: Fix updating ISO QoS PHY
Bluetooth: ISO: unlock on error path in iso_sock_setsockopt()
Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm regression
====================
Link: https://lore.kernel.org/r/20220809001224.412807-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since
commit e6e771b3d8 ("s390/qeth: detach netdevice while card is offline")
there was a timing window during recovery, that qeth_query_card_info could
be sent to the card, even before it was ready for it, leading to a failing
card recovery. There is evidence that this window was hit, as not all
callers of get_link_ksettings() check for netif_device_present.
Use cached values in qeth_get_link_ksettings(), instead of calling
qeth_query_card_info() and falling back to default values in case it
fails. Link info is already updated when the card goes online, e.g. after
STARTLAN (physical link up). Set the link info to default values, when the
card goes offline or at STOPLAN (physical link down). A follow-on patch
will improve values reported for link down.
Fixes: e6e771b3d8 ("s390/qeth: detach netdevice while card is offline")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Link: https://lore.kernel.org/r/20220805155714.59609-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If CONFIG_NVMEM is not set of_nvmem_cell_get, of_nvmem_device_get
functions will return ERR_PTR(-EOPNOTSUPP) and "failed to get nvmem
cell io_impedance_ctrl" error would be reported despite "io_impedance_ctrl"
is completely missing in Device Tree and we should use default values.
Check -EOPNOTSUPP togather with -ENOENT to avoid this situation.
Fixes: 5c2d0a6a07 ("net: phy: dp83867: implement support for io_impedance_ctrl nvmem cell")
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805084843.24542-1-nikita.shubin@maquefel.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case master/slave clock role is not specified (which is default), the
aneg registers will not be written.
The visible impact of this is missing pause advertisement.
So, rework genphy_c45_baset1_an_config_aneg() to be able to write
advertisement registers even if clock role is unknown.
Fixes: 3da8ffd854 ("net: phy: Add 10BASE-T1L support in phy-c45")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805073159.908643-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are use-after-free bugs caused by tst_timer. The root cause
is that there are no functions to stop tst_timer in idt77252_exit().
One of the possible race conditions is shown below:
(thread 1) | (thread 2)
| idt77252_init_one
| init_card
| fill_tst
| mod_timer(&card->tst_timer, ...)
idt77252_exit | (wait a time)
| tst_timer
|
| ...
kfree(card) // FREE |
| card->soft_tst[e] // USE
The idt77252_dev is deallocated in idt77252_exit() and used in
timer handler.
This patch adds del_timer_sync() in idt77252_exit() in order that
the timer handler could be stopped before the idt77252_dev is
deallocated.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220805070008.18007-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
min_gate_len[tc] is supposed to track the shortest interval of
continuously open gates for a traffic class. For example, in the
following case:
TC 76543210
t0 00000001b 200000 ns
t1 00000010b 200000 ns
min_gate_len[0] and min_gate_len[1] should be 200000, while
min_gate_len[2-7] should be 0.
However what happens is that min_gate_len[0] is 200000, but
min_gate_len[1] ends up being 0 (despite gate_len[1] being 200000 at the
point where the logic detects the gate close event for TC 1).
The problem is that the code considers a "gate close" event whenever it
sees that there is a 0 for that TC (essentially it's level rather than
edge triggered). By doing that, any time a gate is seen as closed
without having been open prior, gate_len, which is 0, will be written
into min_gate_len. Once min_gate_len becomes 0, it's impossible for it
to track anything higher than that (the length of actually open
intervals).
To fix this, we make the writing to min_gate_len[tc] be edge-triggered,
which avoids writes for gates that are closed in consecutive intervals.
However what this does is it makes us need to special-case the
permanently closed gates at the end.
Fixes: 55a515b1f5 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220804202817.1677572-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a userspace application starts a blocking connect(), a CALL REQUEST
is sent, the t21 timer is started and the connect is waiting in
x25_wait_for_connection_establishment(). If then for some reason the t21
timer expires before any reaction on the assigned logical channel (e.g.
CALL ACCEPT, CLEAR REQUEST), there is sent a CLEAR REQUEST and timer
t23 is started waiting for a CLEAR confirmation. If we now receive a
CLEAR CONFIRMATION from the peer, x25_disconnect() is called in
x25_state2_machine() with reason "0", which means "normal" call
clearing. This is ok, but the parameter "reason" is used as sk->sk_err
in x25_disconnect() and sock_error(sk) is evaluated in
x25_wait_for_connection_establishment() to check if the call is still
pending. As "0" is not rated as an error, the connect will stuck here
forever.
To fix this situation, also check if the sk->sk_state changed form
TCP_SYN_SENT to TCP_CLOSE in the meantime, which is also done by
x25_disconnect().
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20220805061810.10824-1-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If tsnep_tx_map() fails, then tsnep_tx_unmap() shall start at the write
index like tsnep_tx_map(). This is different to the normal operation.
Thus, add an additional parameter to tsnep_tx_unmap() to enable start at
different positions for successful TX and failed TX.
Fixes: 403f69bbdb ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel test robot found the following warning:
drivers/net/ethernet/engleder/tsnep_main.c:1254:34: warning:
'tsnep_of_match' defined but not used [-Wunused-const-variable=]
of_match_ptr() compiles into NULL if CONFIG_OF is disabled.
tsnep_of_match exists always so use of of_match_ptr() is useless.
Fix warning by dropping of_match_ptr().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This fixes using wrong QoS settings when attempting to send frames while
acting as peripheral since the QoS settings in use are stored in
hconn->iso_qos not in sk->qos, this is actually properly handled on
getsockopt(BT_ISO_QOS) but not on iso_send_frame.
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
syzbot is reporting attempt to cancel uninitialized work at
mgmt_index_removed() [1], for calling cancel_delayed_work_sync() without
INIT_DELAYED_WORK() is not permitted.
INIT_DELAYED_WORK() is called from mgmt_init_hdev() via chan->hdev_init()
from hci_mgmt_cmd(), but cancel_delayed_work_sync() is unconditionally
called from mgmt_index_removed().
Call cancel_delayed_work_sync() only if HCI_MGMT flag was set, for
mgmt_init_hdev() sets HCI_MGMT flag when calling INIT_DELAYED_WORK().
Link: https://syzkaller.appspot.com/bug?extid=b8ddd338a8838e581b1c [1]
Reported-by: syzbot <syzbot+b8ddd338a8838e581b1c@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 0ef08313ce ("Bluetooth: Convert delayed discov_off to hci_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT_DEFER_SETUP shall be considered valid for all states except for
BT_CONNECTED as it is also used when initiated a connection rather then
only for BT_BOUND and BT_LISTEN.
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following warning when building with make C=1:
net/bluetooth/mgmt.c:3821:29: warning: restricted __le16 degrades to integer
net/bluetooth/mgmt.c:4625:9: warning: cast to restricted __le32
Fixes: 600a87490f ("Bluetooth: Implementation of MGMT_OP_SET_BLOCKED_KEYS.")
Fixes: 4c54bf2b09 ("Bluetooth: Add get/set device flags mgmt op")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following warning when build with make C=1:
net/bluetooth/hci_event.c:337:15: warning: restricted __le16 degrades to integer
Fixes: a936612036 ("Bluetooth: Process result of HCI Delete Stored Link Key command")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The following memory corruption can happen since iso_pinfo.base size
did not account for its headers (4 bytes):
net/bluetooth/eir.c
76 memcpy(&eir[eir_len], data, data_len);
^^^^^^^ ^^^^^^^^
77 eir_len += data_len;
78
79 return eir_len;
80 }
The "eir" buffer has 252 bytes and data_len is 252 but we do a memcpy()
to &eir[4] so this can corrupt 4 bytes beyond the end of the buffer.
Fixes: f764a6c2c1 ("Bluetooth: ISO: Add broadcast support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
__hci_cmd_sync returns NULL if the controller responds with a status
event. This is unexpected for the commands sent here, but on
occurrence leads to null pointer dereferences and thus must be
handled.
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The C standard rules for when struct holes are zeroed out are slightly
weird. The existing assignments might initialize everything, but GCC
is allowed to (and does sometimes) leave the struct holes uninitialized,
so instead of using yet another variable and copy the QoS settings just
use a pointer to the stored QoS settings.
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT_ISO_QOS has different semantics when it comes to QoS PHY as it uses
0x00 to disable a direction but that value is invalid over HCI and
sockets using DEFER_SETUP to connect may attempt to use hci_bind_cis
multiple times in order to detect if the parameters have changed, so to
fix the code will now just mirror the PHY for the parameters of
HCI_OP_LE_SET_CIG_PARAMS and will not update the PHY of the socket
leaving it disabled.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Call release_sock(sk); before returning on this error path.
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The patch d0be8347c6: "Bluetooth: L2CAP: Fix use-after-free caused
by l2cap_chan_put" from Jul 21, 2022, leads to the following Smatch
static checker warning:
net/bluetooth/l2cap_core.c:1977 l2cap_global_chan_by_psm()
error: we previously assumed 'c' could be null (see line 1996)
Fixes: d0be8347c6 ("Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not necessary to allocate contiguous physical memory for BPF
program buffer using kcalloc. When the BPF program is large more than
memory page size, kcalloc allocates multiple memory pages from buddy
system. If the device can not provide sufficient memory, for example
in low-end android devices [0], memory allocation for BPF program is
likely to fail.
Test cases in lib/test_bpf.c all pass on ARM64 QEMU.
[0]
AndroidTestSuit: page allocation failure: order:4,
mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=foreground,mems_allowed=0
Call trace:
dump_stack+0xa4/0x114
warn_alloc+0xf8/0x14c
__alloc_pages_slowpath+0xac8/0xb14
__alloc_pages_nodemask+0x194/0x3d0
kmalloc_order_trace+0x44/0x1e8
__kmalloc+0x29c/0x66c
bpf_int_jit_compile+0x17c/0x568
bpf_prog_select_runtime+0x4c/0x1b0
bpf_prepare_filter+0x5fc/0x6bc
bpf_prog_create_from_user+0x118/0x1c0
seccomp_set_mode_filter+0x1c4/0x7cc
__do_sys_prctl+0x380/0x1424
__arm64_sys_prctl+0x20/0x2c
el0_svc_common+0xc8/0x22c
el0_svc_handler+0x1c/0x28
el0_svc+0x8/0x100
Signed-off-by: Aijun Sun <aijun.sun@unisoc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220804025442.22524-1-aijun.sun@unisoc.com
Apparently, no existing selftest covers it. Add a new one where
we load cgroup/bind4 program and attach fentry to it. Calling
bpf_obj_get_info_by_fd on the fentry program should return non-zero
btf_id/btf_obj_id instead of crashing the kernel.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20220804201140.1340684-2-sdf@google.com
When attaching to program, the program itself might not be attached
to anything (and, hence, might not have attach_btf), so we can't
unconditionally use 'prog->aux->dst_prog->aux->attach_btf'.
Instead, use bpf_prog_get_target_btf to pick proper target BTF:
* when attached to dst_prog, use dst_prog->aux->btf
* when attached to kernel btf, use prog->aux->attach_btf
Fixes: b79c9fc955 ("bpf: implement BPF_PROG_QUERY for BPF_LSM_CGROUP")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20220804201140.1340684-1-sdf@google.com
The btf_sock_ids array needs struct mptcp_sock BTF ID for the
bpf_skc_to_mptcp_sock helper.
When CONFIG_MPTCP is disabled, the 'struct mptcp_sock' is not
defined and resolve_btfids will complain with:
[...]
BTFIDS vmlinux
WARN: resolve_btfids: unresolved symbol mptcp_sock
[...]
Add an empty definition for struct mptcp_sock when CONFIG_MPTCP
is disabled.
Fixes: 3bc253c2e6 ("bpf: Add bpf_skc_to_mptcp_sock_proto")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20220802163324.1873044-1-jolsa@kernel.org
The commit d1361840f8 ("tcp: fix SO_RCVLOWAT and RCVBUF autotuning")
add one new (struct proto_ops)->set_rcvlowat method so that a protocol
can override the default setsockopt(SO_RCVLOWAT) behavior.
The prior bpf codes don't check and invoke the protos's set_rcvlowat,
now correct it.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we call xdp_convert_buff_to_frame() to get xdpf, if it returns
NULL, we should check if xdp_page was allocated by xdp_linearize_page().
If it is newly allocated, it should be freed here alone. Just like any
other "goto err_xdp".
Fixes: 44fa2dbd47 ("xdp: transition into using xdp_frame for ndo_xdp_xmit")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse warns:
drivers/net/wireless/microchip/wilc1000/hif.h:218:35: error: marked inline, but without a definition
Remove the inline, it's not needed.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220801110440.13144-1-kvalo@kernel.org
Driver's SME is allowed to fill either BSSID or BSS pointers in struct
cfg80211_connect_resp_params when indicating connect response but a
check in __cfg80211_connect_result() is giving unnecessary warning when
driver's SME fills only BSSID pointer and not BSS pointer in struct
cfg80211_connect_resp_params.
In case of mac80211 with auth/assoc path, it is always expected to fill
BSS pointers in struct cfg80211_connect_resp_params when calling
__cfg80211_connect_result() since cfg80211 must have hold BSS pointers
in cfg80211_mlme_assoc().
So, skip the check for the drivers which support cfg80211 connect
callback, for example with brcmfmac is one such driver which had the
warning:
WARNING: CPU: 5 PID: 514 at net/wireless/sme.c:786 __cfg80211_connect_result+0x2fc/0x5c0 [cfg80211]
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: efbabc1165 ("cfg80211: Indicate MLO connection info in connect and roam callbacks")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
[kvalo@kernel.org: add more info to the commit log]
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220805135259.4126630-1-quic_vjakkam@quicinc.com
Fixes the following warnings observed when building
CONFIG_IPV6_SEG6_LWTUNNEL=y with clang:
net/ipv6/seg6_local.o: warning: objtool: seg6_local_fill_encap() falls
through to next function seg6_local_get_encap_size()
net/ipv6/seg6_local.o: warning: objtool: seg6_local_cmp_encap() falls
through to next function input_action_end()
LLVM can fully unroll loops in seg6_local_get_encap_size() and
seg6_local_cmp_encap(). One issue in those loops is that the induction
variable is initialized to 0. The loop iterates over members of
seg6_action_params, a global array of struct seg6_action_param calling
their put() function pointer members. seg6_action_param uses an array
initializer to initialize SEG6_LOCAL_SRH and later elements, which is
the third enumeration of an anonymous union.
The guard `if (attrs & SEG6_F_ATTR(i))` may prevent this from being
called at runtime, but it would still be UB for
`seg6_action_params[0]->put` to be called; the unrolled loop will make
the initial iterations unreachable, which LLVM will later rotate to
fallthrough to the next function.
Make this more obvious that this cannot happen to the compiler by
initializing the loop induction variable to the minimum valid index that
seg6_action_params is initialized to.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20220802161203.622293-1-ndesaulniers@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid the PHY library call unnecessarily into the suspend/resume functions by
setting phydev->mac_managed_pm to true. The GENET driver essentially does
exactly what mdio_bus_phy_resume() does by calling phy_init_hw() plus
phy_resume().
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220804173605.1266574-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rose /proc code does not serialize timer accesses.
Initial report by Bernard F6BVP Pidoux exhibits overflow amounting
to 116 ticks on its HZ=250 system.
Full timer access serialization would imho be overkill as rose /proc
does not enforce consistency between displayed ROSE_STATE_XYZ and
timer values during changes of state.
The patch may also fix similar behavior in ax25 /proc, ax25 ioctl
and netrom /proc as they all exhibit the same timer serialization
policy. This point has not been reported though.
The sole remaining use of ax25_display_timer - ax25 rtt valuation -
may also perform marginally better but I have not analyzed it too
deeply.
Cc: Thomas DL9SAU Osterried <thomas@osterried.de>
Link: https://lore.kernel.org/all/d5e93cc7-a91f-13d3-49a1-b50c11f0f811@free.fr/
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Bernard Pidoux <f6bvp@free.fr>
Link: https://lore.kernel.org/r/Yuk9vq7t7VhmnOXu@electric-eye.fr.zoreil.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For packets scheduled to RPM and LBK, NIX_AF_PSE_CHANNEL_LEVEL[BP_LEVEL]
selects the TL3 or TL2 scheduling level as the one used for link/channel
selection and backpressure. For each scheduling queue at the selected
level: Setting NIX_AF_TL3_TL2(0..255)_LINK(0..12)_CFG[ENA] = 1 allows
the TL3/TL2 queue to schedule packets to a specified RPM or LBK link
and channel.
There is an issue in the code where NIX_AF_PSE_CHANNEL_LEVEL[BP_LEVEL]
is set to TL3 where as the NIX_AF_TL3_TL2(0..255)_LINK(0..12)_CFG is
configured for TL2 queue in some cases. As a result packets will not
transmit on that link/channel. This patch fixes the issue by configuring
the NIX_AF_TL3_TL2(0..255)_LINK(0..12)_CFG register depending on the
NIX_AF_PSE_CHANNEL_LEVEL[BP_LEVEL] value.
Fixes: caa2da34fd ("octeontx2-pf: Initialize and config queues")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20220802142813.25031-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
