[ Upstream commit 307004e8b2 ]
It seems that when the driver is built-in, the HID bus is
initialized after the driver is loaded, which whould cause
module_hid_driver() to fail.
Fix this by registering the driver after the HID bus using
late_initcall() in accordance with other hwmon HID drivers.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231207210723.222552-1-W_Armin@gmx.de
[groeck: Dropped "compile tested" comment; the patch has been tested
but the tester did not provide a Tested-by: tag]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fefca6c57 ]
The ACPI specification says:
"If an error occurs while obtaining the meter reading or if the value
is not available then an Integer with all bits set is returned"
Since the "integer" is 32 bits in case of the ACPI power meter,
userspace will get a power reading of 2^32 * 1000 miliwatts (~4.29 MW)
in case of such an error. This was discovered due to a lm_sensors
bugreport (https://github.com/lm-sensors/lm-sensors/issues/460).
Fix this by returning -ENODATA instead.
Tested-by: <urbinek@gmail.com>
Fixes: de584afa5e ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231124182747.13956-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7da8a63543 ]
When the lock bit inside SCH5627_REG_CTRL is set, then the virtual
registers become read-only until the next power cycle.
Disallow write access to those registers in such a case.
Tested on a Fujitsu Esprimo P720.
Fixes: aa9f833dfc ("hwmon: (sch5627) Add pwmX_auto_channels_temp support")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f0b28e065 ]
Use bit macros then accessing SCH5627_REG_CTRL, so that people
do not need to look at the datasheet to find out what each bit
does.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stable-dep-of: 7da8a63543 ("hwmon: (sch5627) Disallow write access if virtual registers are locked")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d621a46d05 ]
This reverts commit 393935baa4.
As reported by Ian Nartowicz, this and the next patch
result in a failure to load the driver on Celsius W280.
While the alternative would be to add the board to the DMI
override table, it is quite likely that other systems are
also affected. Revert the offending patches to avoid future
problems.
Fixes: 393935baa4 ("hwmon: (sch56xx-common) Add automatic module loading on supported devices")
Reported-by: Ian Nartowicz <deadbeef@nartowicz.co.uk>
Closes: https://lore.kernel.org/linux-hwmon/20231025192239.3c5389ae@debian.org/T/#t
Cc: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28da9dee35 ]
This reverts commit fd2d53c367.
As reported by Ian Nartowicz, this and the preceding patch
result in a failure to load the driver on Celsius W280.
While the alternative would be to add the board to the DMI
override table, it is quite likely that other systems are
also affected. Revert the offending patches to avoid future
problems.
Fixes: fd2d53c367 ("hwmon: (sch56xx-common) Add DMI override table")
Reported-by: Ian Nartowicz <deadbeef@nartowicz.co.uk>
Closes: https://lore.kernel.org/linux-hwmon/20231025192239.3c5389ae@debian.org/T/#t
Cc: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfff736d3 ]
When build with W=1 and "-Werror=format-truncation", below error is
observed in coretemp driver,
drivers/hwmon/coretemp.c: In function 'create_core_data':
>> drivers/hwmon/coretemp.c:393:34: error: '%s' directive output may be truncated writing likely 5 or more bytes into a region of size between 3 and 13 [-Werror=format-truncation=]
393 | "temp%d_%s", attr_no, suffixes[i]);
| ^~
drivers/hwmon/coretemp.c:393:26: note: assuming directive output of 5 bytes
393 | "temp%d_%s", attr_no, suffixes[i]);
| ^~~~~~~~~~~
drivers/hwmon/coretemp.c:392:17: note: 'snprintf' output 7 or more bytes (assuming 22) into a destination of size 19
392 | snprintf(tdata->attr_name[i], CORETEMP_NAME_LENGTH,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
393 | "temp%d_%s", attr_no, suffixes[i]);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Given that
1. '%d' could take 10 charactors,
2. '%s' could take 10 charactors ("crit_alarm"),
3. "temp", "_" and the NULL terminator take 6 charactors,
fix the problem by increasing CORETEMP_NAME_LENGTH to 28.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Fixes: 7108b80a54 ("hwmon/coretemp: Handle large core ID value")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310200443.iD3tUbbK-lkp@intel.com/
Link: https://lore.kernel.org/r/20231025122316.836400-1-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a5b3370a1 ]
axi_fan_control_irq_handler(), dependent on the private
axi_fan_control_data structure, might be called before the hwmon
device is registered. That will cause an "Unable to handle kernel
NULL pointer dereference" error.
Fixes: 8412b410fa ("hwmon: Support ADI Fan Control IP")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231025132100.649499-1-nuno.sa@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 920057ad52 upstream.
In the regmap conversion in commit 4ef2774511 ("hwmon: (nct6775)
Convert register access to regmap API") I reused the 'reg' variable
for all three register reads in the fan speed calculation loop in
nct6775_update_device(), but failed to notice that the value from the
first one (data->REG_FAN[i]) is actually used in the call to
nct6775_select_fan_div() at the end of the loop body. Since that
patch the register value passed to nct6775_select_fan_div() has been
(conditionally) incorrectly clobbered with the value of a different
register than intended, which has in at least some cases resulted in
fan speeds being adjusted down to zero.
Fix this by using dedicated temporaries for the two intermediate
register reads instead of 'reg'.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 4ef2774511 ("hwmon: (nct6775) Convert register access to regmap API")
Reported-by: Thomas Zajic <zlatko@gmx.at>
Tested-by: Thomas Zajic <zlatko@gmx.at>
Cc: stable@vger.kernel.org # v5.19+
Link: https://lore.kernel.org/r/20230929200822.964-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a148e9b1e upstream.
This seems to be a new revision of the device. RGB controls have changed,
but this driver doesn't touch them anyway.
Fan speed control reported to be working with existing userspace (hidraw)
software, so I assume it's compatible. Fan channel count is the same.
Recently added (0x1e71, 0x2019) seems to be the same device.
Discovered in liquidctl project:
https://github.com/liquidctl/liquidctl/issues/541
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20230219105924.333007-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e247510e1b upstream.
Adding support for new device id
1e71:2019 NZXT NZXT RGB & Fan Controller
Signed-off-by: Herman Fries <baracoder@googlemail.com>
Link: https://lore.kernel.org/r/20221214194627.135692-1-baracoder@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b930dcd8 upstream.
Add a 200ms delay after sending a ctrl report to Quadro,
Octo, D5 Next and Aquaero to give them enough time to
process the request and save the data to memory. Otherwise,
under heavier userspace loads where multiple sysfs entries
are usually set in quick succession, a new ctrl report could
be requested from the device while it's still processing the
previous one and fail with -EPIPE. The delay is only applied
if two ctrl report operations are near each other in time.
Reported by a user on Github [1] and tested by both of us.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/82
Fixes: 752b927951 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230807172004.456968-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ removed Aquaero support as it's not in 6.1 ]
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f38963b9cd upstream.
Skip status check for both pfe1100 and pfe3000 because the communication
error is also observed on pfe1100 devices.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Fixes: 626bb2f3fb hwmon: (pmbus) add driver for BEL PFE1100 and PFE3000
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230804221403.28931-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e146503ac6 upstream.
Industrial processor i3255 supports temperatures -40 deg celcius
to 105 deg Celcius. The current implementation of k10temp_read_temp
rounds off any negative temperatures to '0'. To fix this,
the following changes have been made.
A flag 'disp_negative' is added to struct k10temp_data to support
AMD i3255 processors. Flag 'disp_negative' is set if 3255 processor
is found during k10temp_probe. Flag 'disp_negative' is used to
determine whether to round off negative temperatures to '0' in
k10temp_read_temp.
Signed-off-by: Baskaran Kannan <Baski.Kannan@amd.com>
Link: https://lore.kernel.org/r/20230727162159.1056136-1-Baski.Kannan@amd.com
Fixes: aef17ca127 ("hwmon: (k10temp) Only apply temperature offset if result is positive")
Cc: stable@vger.kernel.org
[groeck: Fixed multi-line comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b153a0bb41 ]
The PMON_CONFIG register on ADM1272 is a 16 bit register. Writing a 8 bit
value into it clears the upper 8 bits of the register, resulting in
unexpected side effects. Fix by writing the 16 bit register value.
Also, it has been reported that temperature readings are sometimes widely
inaccurate, to the point where readings may result in device shutdown due
to errant overtemperature faults. Improve by enabling temperature sampling.
While at it, move the common code for ADM1272 and ADM1278 into a separate
function, and clarify in the error message that an attempt was made to
enable both VOUT and temperature monitoring.
Last but not least, return the error code reported by the underlying I2C
controller and not -ENODEV if updating the PMON_CONFIG register fails.
After all, this does not indicate that the chip is not present, but an
error in the communication with the chip.
Fixes: 4ff0ce227a ("hwmon: (pmbus/adm1275) Add support for ADM1272")
Fixes: 9da9c2dc57 ("hwmon: (adm1275) enable adm1272 temperature reporting")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230602213447.3557346-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6d80df47e ]
The GSC fan pwm temperature register is in centidegrees celcius but the
Linux hwmon convention is to use milidegrees celcius. Fix the scaling.
Fixes: 3bce5377ef ("hwmon: Add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://lore.kernel.org/r/20230606153004.1448086-1-tharvey@gateworks.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0babf89c9c ]
In the unlikely event that something goes wrong with the device and
its registers, the fan_from_reg() function may return 0. This value
will cause a division-by-zero error in the show_pwm() function.
To prevent this, test the value of
fan_from_reg(data->fan_full_speed[nr]) against 0 before performing
the division. If the division-by-zero error is avoided, assign 0 to
the val variable.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: df9ec2dae0 ("hwmon: (f71882fg) Reorder symbols to get rid of a few forward declarations")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230510143537.145060-1-n.zhandarovich@fintech.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93822f5161 ]
The bit flags in pmbus_driver_info functionality for YM-2151E chip were
joined with a comma operator instead of a bitwise OR. This means that
the last constant PMBUS_HAVE_IIN was not OR-ed with the other
PM_BUS_HAVE_* constants for this page but it initialized the next element
of the func array (which was not accessed from anywhere because of the
number of pages).
However, there is no need for setting PMBUS_HAVE_IIN in the 5Vsb page
because this command does not seem to be paged. Obviously, the device
only has one IIN sensor, so it doesn't make sense to query it again from
the second page.
Fixes: 1734b4135a ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Tomáš Pecka <tomas.pecka@cesnet.cz>
Link: https://lore.kernel.org/r/20230420171939.212040-1-tomas.pecka@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 813cc94c78 ]
Smatch reports:
drivers/hwmon/xgene-hwmon.c:757 xgene_hwmon_probe() warn:
'ctx->pcc_comm_addr' from ioremap() not released on line: 757.
This is because in drivers/hwmon/xgene-hwmon.c:701 xgene_hwmon_probe(),
ioremap and memremap is not released, which may cause a leak.
To fix this, ioremap and memremap is modified to devm_ioremap and
devm_memremap.
Signed-off-by: Tianyi Jing <jingfelix@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230318143851.2191625-1-jingfelix@hust.edu.cn
[groeck: Fixed formatting and subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968b66ffeb ]
Fix voltage scaling for chips that have 10.9mV ADCs, where scaling was
not performed.
Fixes: ead8080351 ("hwmon: (it87) Add support for IT8732F")
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230318080543.1226700-2-frank@crawford.emu.id.au
[groeck: Update subject and description to focus on bug fix]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2315332efc ]
It is not sufficient to check of_node in current device.
In some cases, this would cause the sensor registration to fail.
This patch looks for device's ancestors to find a valid of_node if any.
Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Signed-off-by: Phinex Hung <phinex@realtek.com>
Link: https://lore.kernel.org/r/20230321060224.3819-1-phinex@realtek.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab00709310 ]
The ltc2992 drivers uses a mutex and I2C bus access in its GPIO chip `set`
and `get` implementation. This means these functions can sleep and the GPIO
chip should set the `can_sleep` property to true.
This will ensure that a warning is printed when trying to set or get the
GPIO value from a context that potentially can't sleep.
Fixes: 9ca26df1ba ("hwmon: (ltc2992) Add support for GPIOs.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230314093146.2443845-2-lars@metafoo.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5bb73b3f5 ]
The adm1266 driver uses I2C bus access in its GPIO chip `set` and `get`
implementation. This means these functions can sleep and the GPIO chip
should set the `can_sleep` property to true.
This will ensure that a warning is printed when trying to set or get the
GPIO value from a context that potentially can't sleep.
Fixes: d98dfad35c ("hwmon: (pmbus/adm1266) Add support for GPIOs")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230314093146.2443845-1-lars@metafoo.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00d85e8179 ]
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/hwmon/tmp513.c:610:34: error: ‘tmp51x_of_match’ defined but not used [-Werror=unused-const-variable=]
Fixes: 59dfa75e5d ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312193723.478032-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d655e6523 ]
When probing the ucd90320 access to some of the registers randomly fails.
Sometimes it NACKs a transfer, sometimes it returns just random data and
the PEC check fails.
Experimentation shows that this seems to be triggered by a register access
directly back to back with a previous register write. Experimentation also
shows that inserting a small delay after register writes makes the issue go
away.
Use a similar solution to what the max15301 driver does to solve the same
problem. Create a custom set of bus read and write functions that make sure
that the delay is added.
Fixes: a470f11c5b ("hwmon: (pmbus/ucd9000) Add support for UCD90320 Power Sequencer")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230312160312.2227405-1-lars@metafoo.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c93f5e2ab5 ]
ret is set to 0 which do not indicate an error.
Return -EINVAL instead.
Fixes: a9e9dd9c6d ("hwmon: (ina3221) Read channel input source info from DT")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://lore.kernel.org/r/20230310075035.246083-1-marcus.folkesson@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb090e64cf ]
In xgene_hwmon_probe, &ctx->workq is bound with xgene_hwmon_evt_work.
Then it will be started.
If we remove the driver which will call xgene_hwmon_remove to clean up,
there may be unfinished work.
The possible sequence is as follows:
Fix it by finishing the work before cleanup in xgene_hwmon_remove.
CPU0 CPU1
|xgene_hwmon_evt_work
xgene_hwmon_remove |
kfifo_free(&ctx->async_msg_fifo);|
|
|kfifo_out_spinlocked
|//use &ctx->async_msg_fifo
Fixes: 2ca492e22c ("hwmon: (xgene) Fix crash when alarm occurs before driver probe")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230310084007.1403388-1-zyytlz.wz@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48e8186870 ]
The wrong bits are masked in the hysteresis register; indices 0 and 2
should zero bits [7:4] and preserve bits [3:0], and index 1 should zero
bits [3:0] and preserve bits [7:4].
Fixes: 1c301fc539 ("hwmon: Add a driver for the ADT7475 hardware monitoring chip")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230222005228.158661-3-tony.obrien@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f8d1e3b6f ]
Throughout the ADT7475 driver, attributes relating to the temperature
sensors are displayed in the order Remote 1, Local, Remote 2. Make
temp_st_show() conform to this expectation so that values set by
temp_st_store() can be displayed using the correct attribute.
Fixes: 8f05bcc33e ("hwmon: (adt7475) temperature smoothing")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230222005228.158661-2-tony.obrien@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2fbb848b65 upstream.
Commit 4ef2774511 ("hwmon: (nct6775) Convert register access to
regmap API") fumbled the shifting & masking of the fan_div values such
that odd-numbered fan divisors would always be set to zero. Fix it so
that we actually OR in the bits we meant to.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 4ef2774511 ("hwmon: (nct6775) Convert register access to regmap API")
Cc: stable@kernel.org # v5.19+
Link: https://lore.kernel.org/r/20230102212857.5670-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f00093608f upstream.
The find_last_bit() call produces the index of the highest-numbered
core in core_mask; because cores are numbered from zero, the number of
elements we need to allocate is one more than that.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: stable@kernel.org # v5.18
Fixes: bf3608f338 ("hwmon: peci: Add cputemp driver")
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20230202021825.21486-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3b3747d02 ]
New ASUS B650/B660/X670 boards firmware have not exposed WMI monitoring
GUID and entrypoint method WMBD could be implemented for different device
UID.
Implement the direct call to entrypoint method for monitoring the device
UID of B550/X570 boards.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Co-developed-by: Ahmad Khalifa <ahmad@khalifa.ws>
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230111212241.7456-1-pauk.denis@gmail.com
[groeck: Fix multi-line formatting]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d03bbff45 ]
Coretemp's platform driver is unconventional. All the real work is done
globally by the initcall and CPU hotplug notifiers, while the "driver"
effectively just wraps an allocation and the registration of the hwmon
interface in a long-winded round-trip through the driver core. The whole
logic of dynamically creating and destroying platform devices to bring
the interfaces up and down is error prone, since it assumes
platform_device_add() will synchronously bind the driver and set drvdata
before it returns, thus results in a NULL dereference if drivers_autoprobe
is turned off for the platform bus. Furthermore, the unusual approach of
doing that from within a CPU hotplug notifier, already commented in the
code that it deadlocks suspend, also causes lockdep issues for other
drivers or subsystems which may want to legitimately register a CPU
hotplug notifier from a platform bus notifier.
All of these issues can be solved by ripping this unusual behaviour out
completely, simply tying the platform devices to the lifetime of the
module itself, and directly managing the hwmon interfaces from the
hotplug notifiers. There is a slight user-visible change in that
/sys/bus/platform/drivers/coretemp will no longer appear, and
/sys/devices/platform/coretemp.n will remain present if package n is
hotplugged off, but hwmon users should really only be looking for the
presence of the hwmon interfaces, whose behaviour remains unchanged.
Link: https://lore.kernel.org/lkml/20220922101036.87457-1-janusz.krzysztofik@linux.intel.com/
Link: https://gitlab.freedesktop.org/drm/intel/issues/6641
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Link: https://lore.kernel.org/r/20230103114620.15319-1-janusz.krzysztofik@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1ffd3c462 ]
Currently for broken fan driver returns value calculated based on error
code (0xFF) in related fan speed register.
Thus, for such fan user gets fan{n}_fault to 1 and fan{n}_input with
misleading value.
Add check for fan fault prior return speed value and return zero if
fault is detected.
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20230212145730.24247-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 178b01eccf ]
ltc2945_val_to_reg errors were not being handled
which would have resulted in register being set to
0 (clamped) instead of being left alone.
Fixes: 6700ce035f ("hwmon: Driver for Linear Technologies LTC2945")
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca8fd8c16a ]
A user complained that the ftsteutates driver was displaying
bogus values since its introduction. This happens because the
sensor measurements need to be scaled in order to produce
meaningful results:
- the fan speed needs to be multiplied by 60 since its in RPS
- the temperature is in degrees celsius and needs an offset of 64
- the voltage is in 1/256 of 3.3V
The offical datasheet says the voltage needs to be divided by 256,
but this is likely an off-by-one-error, since even the BIOS
devides by 255 (otherwise 3.3V could not be measured).
The voltage channels additionally need a board-specific multiplier,
however this can be done by the driver since its board-specific.
The reason the missing scaling of measurements is the way Fujitsu
used this driver when it was still out-of-tree. Back then, all
scaling was done in userspace by libsensors, even the generic one.
Tested on a Fujitsu DS3401-B1.
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20221224041855.83981-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b744db17ab ]
Add the missing unlock before return from function jc42_write()
in the error handling case.
Fixes: 37dedaee8bc6 ("hwmon: (jc42) Convert register access and caching to regmap/regcache")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221027062931.598247-1-yangyingliang@huawei.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1864069c69 ]
Boards such as
* ProArt B550-CREATOR
* ProArt Z490-CREATOR 10G
* ROG CROSSHAIR VIII EXTREME
* ROG CROSSHAIR VIII HERO (WI-FI)
* TUF GAMING B550M-E
* TUF GAMING B550M-E (WI-FI)
* TUF GAMING B550M-PLUS WIFI II
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
This commit adds such boards to the WMI monitoring list.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Reported-by: yutesdb <mundanedefoliation@gmail.com>
Tested-by: yutesdb <mundanedefoliation@gmail.com>
Link: https://lore.kernel.org/r/20221114214456.3891-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 364ffd2537 ]
There are fields 'last_hwmon_state' and 'last_thermal_state' in the
structure 'emc2305_cdev_data', which respectively store the cooling state
set by the 'hwmon' and 'thermal' subsystem, and the driver author hopes
that if the state set by 'hwmon' is lower than the value set by 'thermal',
the driver will just save it without actually setting the pwm. Currently,
the 'last_thermal_state' also be updated by 'hwmon', which will cause the
cooling state to never be set to a lower value. This patch fixes that.
Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com>
Link: https://lore.kernel.org/r/20221206055331.170459-2-nanpuyue@gmail.com
Fixes: 0d8400c5a2 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.")
[groeck: renamed emc2305_set_cur_state_shim -> __emc2305_set_cur_state]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d50591ebf ]
The definitions of 'EMC2305_REG_PRODUCT_ID' and 'EMC2305_REG_DEVICE' are
both '0xfd', they actually return the same value, but the values returned
by emc2301/2/3/5 are different, so probe emc2301/2/3 will fail, This patch
fixes that.
Signed-off-by: Xingjiang Qiao <nanpuyue@gmail.com>
Link: https://lore.kernel.org/r/20221206055331.170459-1-nanpuyue@gmail.com
Fixes: 0d8400c5a2 ("hwmon: (emc2305) add support for EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 084ed144c4 ]
The JC42 compatible thermal sensor on Kingston KSM32ES8/16ME DIMMs
(using Micron E-Die) is an ST Microelectronics STTS2004 (manufacturer
0x104a, device 0x2201). It does not keep the previously programmed
minimum, maximum and critical temperatures after system suspend and
resume (which is a shutdown / startup cycle for the JC42 temperature
sensor). This results in an alarm on system resume because the hardware
default for these values is 0°C (so any environment temperature greater
than 0°C will trigger the alarm).
Example before system suspend:
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C)
(high = +85.0°C, hyst = +85.0°C)
(crit = +95.0°C, hyst = +95.0°C)
Example after system resume (without this change):
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C) ALARM (HIGH, CRIT)
(high = +0.0°C, hyst = +0.0°C)
(crit = +0.0°C, hyst = +0.0°C)
Apply the cached values from the JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER, JC42_REG_TEMP_CRITICAL and JC42_REG_SMBUS (where
the SMBUS register is not related to this issue but a side-effect of
using regcache_sync() during system resume with the previously
cached/programmed values. This fixes the alarm due to the hardware
defaults of 0°C because the previously applied limits (set by userspace)
are re-applied on system resume.
Fixes: 175c490c9e ("hwmon: (jc42) Add support for STTS2004 and AT30TSE004")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-3-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
