Even if field order is set to V4L2_FIELD_ALTERNATE, the width and height
values in struct v4l2_mbus_framefmt still refer to frame size, not field
size.
Fixes: 4f57d27be2 ("[media] tvp5150: fix tvp5150_fill_fmt()")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To let userspace propagate formats downstream in a media controller
scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow
setting and getting the format. Incidentally, tvp5150_fill_fmt was
implemented for this pad, not for the new analog input pad (now pad 0,
DEMOD_PAD_IF_INPUT).
Fixes: 55606310e7 ("[media] tvp5150: create the expected number of pads")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MC support is needed by the em28xx driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert v4l2_clk to normal clk and enable the clock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert ov2640 to a standard subdev driver. The soc-camera driver no longer
uses this driver, so it can safely be converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The colorspace is independent of whether YUV or RGB is sent to the SoC.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add DT support. Use it to get the reset and pwdn pins (if there are any).
Tested with one sensor requiring reset/pwdn and one sensor that doesn't
have reset/pwdn pins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Get the clock for this sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop unnecesary memset. Drop the unnecessary extendedmode check and
set the V4L2_CAP_TIMEPERFRAME capability.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add v4l2-async support for this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After changes to v4l2_clk API introduced in v4.1 by commits a37462b919
'[media] V4L: remove clock name from v4l2_clk API' and 4f528afcfb
'[media] V4L: add CCF support to the v4l2_clk API', ov6650 sensor
stopped responding because v4l2_clk_get(), still called with
depreciated V4L2 clock name "mclk", started to return respective CCF
clock instead of the V4l2 one registered by soc_camera. Fix it by
calling v4l2_clk_get() with NULL clock name.
Created and tested on Amstrad Delta against Linux-4.7-rc3 with
omap1_camera fixes.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
After this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
alias: of:N*T*Ctoshiba,et8ek8C*
alias: of:N*T*Ctoshiba,et8ek8
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without calling tc358743_set_csi after stopping streaming (or calling
tc358743_s_dv_timings or tc358743_set_fmt from userspace after stopping
the stream), the i.MX6 MIPI CSI2 input fails waiting for lanes to enter
STOP state when streaming is started again.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While testing with CONFIG_UBSAN, I got this warning:
drivers/media/i2c/tc358743.c: In function 'tc358743_probe':
drivers/media/i2c/tc358743.c:1930:1: error: the frame size of 2480 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
The problem is that the i2c_rd8/wr8/rd16/... functions in this driver pass
a pointer to a local variable into a common function, and each call to one
of them adds another variable plus redzone to the stack.
I also noticed that the way this is done is broken on big-endian machines,
as we copy the registers in CPU byte order.
To address both those problems, I'm adding two helper functions for reading
a register of up to 32 bits with correct endianess and change all other
functions to use that instead. Just to be sure we don't get the problem
back with changed optimizations in gcc, I'm also marking the new functions
as 'noinline', although my tests with gcc-7 don't require that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix typos and add the following to the scripts/spelling.txt:
swithc||switch
swithced||switched
swithcing||switching
Link: http://lkml.kernel.org/r/1481573103-11329-3-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a compiler warning due to an unused but assigned variable.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The control for +5V Power detection must also be updated when the EDID is
not present.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Originally Toshiba told us that the only way to disable HDCP was to
set the receiver in repeater mode, that would make the authentication
fail because of missing software support. It has worked fine with all
the sources we and our customers has used, until it was reported
problems with Apple MacBook (Retina, 12-inch, Early 2015)
(https://support.apple.com/kb/SP712?locale=en_US&viewlocale=en_US)
with Apple A1612 USB type-C multiport adapter
(http://www.apple.com/shop/product/MJ1K2AM/A/usb-c-digital-av-multiport-adapter)
Finally Toshiba came up with a hidden bit that is named "Manual HDCP
authentication". In this patch the original "repeater mode" concept is
removed, and the new bit is set instead.
With his patch HDCP is disabled when connected to the Apple MacBook
and all other sources we have tested so far. The Apple MacBook is
constantly trying to authenticate, but fails and continues to transmit
unencrypted video.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of CSI lanes that should be used is set to the CSI_CONTROL
register by indirectly writing to the CSI_CONFW register. When the
number of lanes is read back from the CSI_CONTROL register the value
is usually correct, but we have seen that it suddenly is 1 for a short
moment before the correct value is restored again.
Toshiba have not figured out why that happen, but we have found it
safer to store the value in the driver.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
v4l2_i2c_subdev_init(...,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_ops i;
File size before:
text data bss dec hex filename
2732 608 8 3348 d14 drivers/media/i2c/ml86v7667.o
File size after:
text data bss dec hex filename
3100 232 8 3340 d0c drivers/media/i2c/ml86v7667.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File size before:
text data bss dec hex filename
1809 872 0 2681 a79 drivers/media/i2c/ak881x.o
File size after:
text data bss dec hex filename
2185 496 0 2681 a79 drivers/media/i2c/ak881x.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_pad_ops structures are stored in the pad field
of the v4l2_subdev_ops structure and this field is of type const.
As the v4l2_subdev_pad_ops structures are never modified, they can be
declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_pad_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.pad=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_pad_ops i;
File size before:
text data bss dec hex filename
7633 512 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
File size after:
text data bss dec hex filename
7761 384 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This delay is in non-atomic context and it does not seem to be
time-critical so relax it to allow the timer subsystem to optimize
hrtimers.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/pad/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File sizes before:
text data bss dec hex filename
7810 736 16 8562 2172 drivers/media/i2c/mt9p031.o
9652 736 24 10412 28ac drivers/media/i2c/mt9v032.o
4613 552 20 5185 1441 drivers/media/i2c/noon010pc30.o
2615 552 8 3175 c67 drivers/media/i2c/s5k6a3.o
File sizes after:
text data bss dec hex filename
8322 232 16 8570 217a drivers/media/i2c/mt9p031.o
10164 232 24 10420 28b4 drivers/media/i2c/mt9v032.o
4933 232 20 5185 1441 drivers/media/i2c/noon010pc30.o
2935 232 8 3175 c67 drivers/media/i2c/s5k6a3.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 25ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Reviwed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpiod API checks for NULL descriptors, there's no need to duplicate
the check in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add driver for et8ek8 sensor, found in Nokia N900 main camera. Can be
used for taking photos in 2.5MP resolution with fcam-dev.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bool values should be negated using logical operators. Using bitwise operators
results in unexpected and possibly incorrect results.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The loop over the ov2659_formats[] array just a few lines above
verifies that mf->code matches the selected array entry.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The adv7604 driver platform data contains fields for configuring the drive
strength of the output pins. When probing the driver through DT these
fields are not explicitly initialized, which means they are left at 0. This
is a reserved setting for the drive strength configuration though and can
cause signal integrity issues.
Whether these signal integrity issues are visible depends on the PCB
specifics (e.g. the higher the load capacitance for the output the more
visible the issue). But it has been observed on existing solutions at high
pixel clock rates.
Initialize the drive strength settings to the power-on-reset value of the
device when probing through devicetree to avoid this issue.
Fixes: 0e158be0162b ("adv7604: Add DT support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If 'ov9640_reg_read()' does not return 0, then 'val' is left unmodified.
As it is not initialized either, the return value can be anything.
It is likely that returning the error code was expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the FSF's postal address from the source code files that typically
contain mostly the license text. Of the 628 removed instances, 578 are
outdated.
The patch has been created with the following command without manual edits:
git grep -l "675 Mass Ave\|59 Temple Place\|51 Franklin St" -- \
drivers/media/ include/media|while read i; do i=$i perl -e '
open(F,"< $ENV{i}");
$a=join("", <F>);
$a =~ s/[ \t]*\*\n.*You should.*\n.*along with.*\n.*(\n.*USA.*$)?\n//m
&& $a =~ s/(^.*)Or, (point your browser to) /$1To obtain the license, $2\n$1/m;
close(F);
open(F, "> $ENV{i}");
print F $a;
close(F);'; done
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYYGCgAAoJEHm+PkMAQRiGjVMH/R1WKLSCVyU2QboSTZVyBGqU
6E42pMalPNaY72uxf29ZmUzds1uV5KyFn7OntsyD4qc+sQb2wxG5PvMSYAsL7HKN
lTFiW738zC9Hfx8MzC/fHLGm/7HTHpPFndZJkDOJjIPnS0MeTHAmOFM+RwCRq+px
5uvRHV4Z8yibHtijET6GqCywV0gw/uyXCi6xJfJNAspnj3hsm3ZXKJ0JPvP2ja+V
yhdnWYHDEQwRs6FyNtIWnfjH92XilVn4KcOtwnb1pFahALiTmmVqJVMiGartagqJ
fPRw98B3YHwmZpEc2SDbXaZi36WLu4hcWvvDa22SN/srXwYIzzblEwuNq1+fiBw=
=X7z+
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc1' into patchwork
Linux 4.10-rc1
* tag 'v4.10-rc1': (11427 commits)
Linux 4.10-rc1
powerpc: Fix build warning on 32-bit PPC
avoid spurious "may be used uninitialized" warning
mm: add PageWaiters indicating tasks are waiting for a page bit
mm: Use owner_priv bit for PageSwapCache, valid when PageSwapBacked
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
...
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A rare randconfig build failure shows up in this driver when
the CRC32 helper is not there:
drivers/media/built-in.o: In function `s5k4ecgx_s_power':
s5k4ecgx.c:(.text+0x9eb4): undefined reference to `crc32_le'
This adds the 'select' that all other users of this function have.
Fixes: 8b99312b72 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The s_stream() handler incorrectly writes the whole MISC_CTL register to
enable or disable the outputs, overriding the output pinmuxing
configuration. Fix it to only touch the output enable bits.
The CONF_SHARED_PIN register is also written by the same function,
resulting in muxing the INTREQ signal instead of the VBLK/GPCL signal on
the INTREQ/GPCL/VBLK pin. As the driver doesn't support interrupts this
is obviously incorrect, and breaks operation on other devices. Fix it by
removing the write.
Cc: stable@vger.kernel.org # For Kernel 4.5 and upper
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FID/GLCO/VLK/HVLK and INTREQ/GPCL/VBLK pins are muxed differently
depending on whether the input is an S-Video or composite signal. The
comment that explains the logic doesn't reflect the code. It appears
that the comment is incorrect, as disabling the output data bus in
composite mode makes no sense. Update the comment to match the code.
While at it define macros for the MISC_CTL register bits, the code is
too confusing with numerical values.
Cc: stable@vger.kernel.org # For Kernel 4.5 and upper
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The tvp5150 doesn't support format setting through the subdev pad API
and thus implements the set format handler as a get format operation.
The single handler, tvp5150_fill_fmt(), resets the device by calling
tvp5150_reset(). This causes malfunction as the device can be reset at
will, possibly from userspace when the subdev userspace API is enabled.
The reset call was added in commit ec2c4f3f93 ("[media] media:
tvp5150: Add mbus_fmt callbacks"), probably as an attempt to set the
device to a known state before detecting the current TV standard.
However, the get format handler doesn't access the hardware to get the
TV standard since commit 963ddc63e2 ("[media] media: tvp5150: Add
cropping support"). There is thus no need to reset the device when
getting the format.
However, removing the tvp5150_reset() from the get/set format handlers
results in the function not being called at all if the bridge driver
doesn't use the .reset() operation. The operation is nowadays abused and
shouldn't be used, so shouldn't expect bridge drivers to call it. To
make sure the device is properly initialize, move the reset call from
the format handlers to the probe function.
Cc: stable@vger.kernel.org # For Kernel 4.5 and upper
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The smiapp_suspend() and smiapp_resume() functions will end up being unused
if CONFIG_PM is enabled but CONFIG_PM_SLEEP is disabled, causing a
compiler warning from both of the function definitions. Fix this by
marking the functions with __maybe_unused.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Power on the sensor when the module is loaded and power it off when it is
removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A break is missing resulting in the hue control enabling or disabling
the decode completely. Fix it.
Fixes: c43875f661 ("[media] tvp5150: replace MEDIA_ENT_F_CONN_TEST by a control")
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function is large and called in several places, don't inline it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function is only referenced as a handler in the tvp5150_sd_media_ops
structure, which is only used when CONFIG_MEDIA_CONTROLLER is set. Don't
define the function and the structure when the configuration option is
unset to avoid an unused function warning.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cec_allocate_adapter function doesn't need the parent device, only the
cec_register_adapter function needs it.
Drop the cec_devnode parent field, since devnode.dev.parent can be used
instead.
This change makes the framework consistent with other frameworks where the
parent device is not used until the device is registered.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Unfortunately, KERN_CONT doesn't work with dev_foo(),
producing weird messages like:
tvp5150 6-005c: tvp5150: read 0xf6 = 0xff
ff
So, we need to get rid of it.
As we're always printing read/write in hexa when dumping
multiple register values, also remove the "0x" from the
read/write debug messages too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When returning results via v4l2_subdev_core_ops.log_status,
use dev_foo() call, instead of just calling printk()
directly, without even specifying the log message level.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using the v4l_foo() macros, just use the
kernel-wide dev_foo() macros, as there's no good reason
to use something else.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drivers using dev_foo() macro should not use KERN_CONT, as, internally,
those macros work as if all strings were terminated by a \n. So, doing:
dev_info(&client->dev, "%s ", client->name);
printk(KERN_CONT "supports radio, mode is autodetect and autoselect");
Would produce the following output:
msp3400 6-0044: msp3400
supports radio, mode is autodetect and autoselect
As there's no good reason to use KERN_CONT, let's rewrite the code
to avoid that, allowing this driver to be converted to dev_foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last open issues have been addressed, so it is time to move
this out of staging and into the mainline and to move the public
cec headers to include/uapi/linux.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Obtain the correct timings based on the VIC code from the AVI InfoFrame.
It does a sanity check to see if at least the measured width and height
are in line with what the VIC code reports. If not, then use the timings
instead of the VIC code (as per the CEA-861 spec).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A recent rework accidentally left a debugging printk untouched while
changing the meaning of the variables, leading to an uninitialized
variable being printed:
drivers/media/i2c/ir-kbd-i2c.c: In function 'get_key_haup_common':
drivers/media/i2c/ir-kbd-i2c.c:62:2: error: 'toggle' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This prints the correct one instead, as we did before the patch.
Fixes: 00bb820755 ("[media] rc: Hauppauge z8f0811 can decode RC6")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a type with explicit endianness in machine to big endian conversion.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation states that the "default-input" property should reside
directly in the node of the device. This adjusts the parsing to make the
implementation consistent with the documentation.
Based on patch by William Towle <william.towle@codethink.co.uk>.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The advertised V4L2 pixel format and Media Bus code don't match.
The current media bud code advertised is MEDIA_BUS_FMT_YUYV8_2X8
which does not reflect what the encoder actually outputs.
This encoder generate MEDIA_BUS_FMT_UYVY8_2X8 so advertise as such.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Delay suspending the device by 1000 ms by default. This is done on
explicit power off through s_power() callback, through releasing the
file descriptor, NVM read or when the probe finishes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch to runtime PM in sensor power management. The internal power count
is thus removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the suspend and resume ops for freeze, thaw, poweroff and restore
callbacks as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dev field of the v4l2_subdev was left NULL for the pixel array and
binner sub-devices. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Checking that the mutex is not acquired is unnecessary for user processes
are stopped by this point. Drop the check.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't complain about a failure to compute the pre_pll divisor. The
function is used to determine whether a particular combination of bits per
sample value and a link frequency can be used, in which case there are
lots of unnecessary driver messages. During normal operation the failure
generally does not happen. Use dev_dbg() instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The first time the sensor is powered on, the information is not yet
available.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The media bus code obtained for try format may have been a code that the
sensor did not even support. Use a supported code with the current pixel
order.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The code probably has been unindented at some point but rewrapping has not
been done. Do it now.
Also remove a useless memory allocation failure message.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide more debugging information on reading the frame layout.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Besides the image data, SMIA++ compliant sensors also provide embedded
data in form of registers used to capture the image. Store this
information for later use in frame descriptor and routing.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace plain value 2 with SMIAPP_PADS when referring to the number of
pads.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The initialisation of the source sub-device is somewhat different as it's
not created by the smiapp driver itself. Remove redundancy in initialising
the two kind of sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The information gathered during frame format reading will be required
earlier in the initialisation when it was available. Also return an error
if frame format cannot be obtained.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The smiapp_probe() is the sole caller of smiapp_init(). Unify the two.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the registered() callback failed, resources were left unaccounted for.
Fix this, as well as add unregistering the sub-devices in driver
unregistered() callback.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialise the sensor in probe. The reason why it wasn't previously done
in case of platform data was that the probe() of the driver that provided
the clock through the set_xclk() callback would need to finish before the
probe() function of the smiapp driver. The set_xclk() callback no longer
exists.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead, calculate how much is needed and then allocate the memory
dynamically.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The same pixel array size is required for the active format of each
sub-device sink pad and try format of each sink pad of each opened file
handle as well as for the native size rectangle.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the loop in sub-device registration and create each sub-device
explicitly instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This allows determining the number of pads in the entity based on the
sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Define the number of pads explicitly in initialising the sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify smiapp_init() by moving the initialisation of individual
sub-devices to a separate function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver has printk continuation lines for
debugging purposes. Since commit 563873318d
("Merge branch 'printk-cleanups'"), this won't work as expected
anymore. So, let's add KERN_CONT to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardware does not decode the 16, 20 or 24 bit variety.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the V4L2_SUBDEV_FORMAT_TRY is used in set_fmt the width, height etc
would not be filled.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The media bus format reported by the adv7180 is wrong. Steve Longerbeam
posted a patch which changed the format to UYVY8_2X8 with the commit
message:
Change the media bus format from YUYV8_2X8 to UYVY8_2X8. Colors
now look correct when capturing with the i.mx6 backend. The other
option is to set the SWPC bit in register 0x27 to swap the Cr and Cb
output samples.
The rcar-vin driver was developed and tested with the adv7180 and
therefor suffers from the same issue, looking for the wrong media bus
format. The two errors corrected each other.
This patch takes Steve's patch and merge it with a fix for rcar-vin
driver. The rcar-vin driver is used used in together with the adv7180
och Koelsch and this ensures it will not break while fixing the adv7180
issue. I checked wit Steve and he was fine with me merging the patches.
ADV7180 parts:
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The new ad5820 driver uses #ifdef to hide the suspend/resume functions,
but gets it wrong when CONFIG_PM_SLEEP is disabled:
drivers/media/i2c/ad5820.c:286:12: error: 'ad5820_resume' defined but not used [-Werror=unused-function]
drivers/media/i2c/ad5820.c:274:12: error: 'ad5820_suspend' defined but not used [-Werror=unused-function]
This replaces the #ifdef with a __maybe_unused annotation that is
simpler and harder to get wrong, avoiding the warning.
Fixes: bee3d51156 ("[media] ad5820: Add driver for auto-focus coil")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow the sub-device to be probed asynchronously so a bridge driver that's
waiting for the device can be notified and its .bound callback executed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: H . Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The SPI driver looked a bit lonely in the config menu, and it didn't
support the autoselect. Shift things around a bit so it looks more logical.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver used integers for what boolean would have been a better fit.
Use boolean instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
SMIA++ supports 14 and 16 bits per pixel formats as well. Add support to
these formats in the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the mt9m111 is now working as a standalone v4l2 subdevice sensor,
move it out of soc_camera directory and sever its dependency on
soc_camera.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mt9m111 being a camera sensor, its colorspace should always be SRGB, for
both RGB based formats or YCbCr based ones.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the soc_camera adherence. Mostly the change removes the power
manipulation provided by soc_camera, and instead :
- powers on the sensor when the s_power control is activated
- powers on the sensor in initial probe
- enables and disables the MCLK provided to it in power on/off
This patch also drops support for inverters on synchronisation and clock
lines. It is assumed, if any board ever needs such inverters, support
for them can be added in the future
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock framework is generally so well supported that there's no reason
to keep this one around.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch from the old gpio API to the new descriptor based gpiod API.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The data may now be const as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock may be provided by a driver which is yet to probe. Print the
actual error code as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is really configuration to the driver originating from DT or
elsewhere. Do not call it platform data.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Unify enforced 8-bit read access with that based on actual need.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver is using the struct v4l2_subdev_core_ops .registered_async
callback to register the connector entities and create the pad links
after the subdev entity has been registered with the media device.
But the .registered_async callback isn't needed since the v4l2 core
already calls the struct v4l2_subdev_internal_ops .registered callback
in v4l2_device_register_subdev(), after media_device_register_entity().
So, use the .registered() callback instead of the .registered_async()
that is going to be removed in a following patch since isn't needed.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENOMEM from the i2c client register error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The old cropcap video op is now only used to pass the pixelaspect
ratio, so rename it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace all calls to g/s_crop by calls to the get/set_selection pad ops.
Remove the old g/s_crop video ops since they are now no longer used.
The cropcap video op is now only used to pass pixelaspect information,
and is only needed if the pixelaspect is not 1:1.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some targets control the ADV7180 power pin via a gpio, so add
optional support for "powerdown" pin control.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue work_queue is involved in EDID (Extended Display
Identification Data) handling.
It has a single work item(&state->edid_handler) and hence
doesn't require ordering. It is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
&state->edid_handler is a self requeueing work item and it has been
been sync cancelled in ad9389b_remove() to ensure that nothing is
pending when the driver is disconnected.
The unused label err_unreg has also been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds support for AD5820 autofocus coil, found for example in
Nokia N900 smartphone.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Access to the interrupt page registers has been broken since at least
commit 3999e5d01d ("[media] adv7180: Do implicit register paging").
That commit forgot to add the interrupt page number to the register
defines.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The adv7511 will automatically fill in the VIC code in the AVI InfoFrame
based on the timings of the incoming pixelport signals.
However, to have this work correctly it needs to specify the fps
value in a register. After doing this the proper VIC code is filled in.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Correctly set the h/vsync polarities instead of keeping to the
default (positive).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a number of bugs that appeared when support for mediabus formats was
added:
- Support for V4L2_DV_RGB_RANGE_FULL/LIMITED should only be enabled
for HDMI RGB formats, not for YCbCr formats. Since, as the name
says, this setting is for RGB only. So read the InfoFrame to check
the format.
- the quantization range for the pixelport depends on whether the
mediabus code is RGB or not: if it is RGB, then produce full range
RGB values, otherwise produce limited range YCbCr values.
This means that the op_656_range and alt_data_sat fields of the
platform data are no longer used and these will be removed in a
following patch.
- when setting up a new format the RGB quantization range settings
were never updated. Do so, since this depends on the format.
- fix the log_status output which was confusing and incorrect.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 1fb69bfd29 (adv7511: improve
colorspace handling) introduced a number of bugs, specifically with
regards to YCbCr output and quantization range handling:
- if the output is not RGB, then disable the full-to-limited range
CSC matrix since that is meant for RGB formats. YCbCr formats are
always limited range, so there is nothing to convert. (OK, full
range YCbCr is possible, but we don't support that right now).
- the mediabus code that was passed to adv7511_set_fmt was always cleared
by the memset in adv7511_fill_format. This made it effectively impossible
to select YCbCr output.
- adv7511_set_fmt never updated the rgb quantization range.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The IT Content bit has nothing to do with CE vs IT timings.
Delete this code. This will also fix a bug where this could
override the 'content type' control, which is actually the
correct place to set/clear the ITC bit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Nobody is using these ops anymore, so remove these callbacks from
the subdev drivers that still have them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The part can be reset by a low pulse on the RESET pin (i.e. a hardware
reset) with a minimum width of 5 ms. It is recommended to wait 5 ms
after the low pulse before an I2C write is performed to the part.
For safety reasons, the delays will be between 5 and 10 ms.
The RESET pin can be tied high, so the GPIO is optional.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in adv76xx_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in tc358743_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in adv7842_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7511 driver.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[k.debski@samsung.com: Merged changes from CEC Updates commit by Hans Verkuil]
Signed-off-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7842 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7604 driver.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[k.debski@samsung.com: Merged changes from CEC Updates commit by Hans Verkuil]
[k.debski@samsung.com: add missing methods cec/io_write_and_or]
[k.debski@samsung.com: change adv7604 to adv76xx in added functions]
[hansverk@cisco.com: use _clr_set instead of _and_or]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dv_timings_cap() and enum_dv_timings() pad operations take a pad
number as an input argument and return the DV timings capabilities and
list of supported DV timings for that pad.
Commit bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings
helpers") broke this as it started ignoring the pad number, always
returning the information associated with the currently selected input.
Fix it.
Fixes: bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings helpers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 controls for Auto Exposure Control and Auto Gain
Control settings. These settings include low pass filter, update
frequency of these settings and the update interval for those units.
[Avoid forward declarations]
[Fix 80 columns limit violation]
[Rename controls to avoid underscores in names]
[Fix the AEC maximum shutter width on MT9V032]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The power_on function of the driver resets the chip and sets the
CHIP_CONTROL register to 0. This switches the operating mode to slave.
The s_stream function sets the correct mode. But this caused problems on
a board where the camera chip is operated as master. The camera started
after a random amount of time streaming an image, I observed between 10
and 300 seconds.
The STRFM_OUT and STLN_OUT pins are not connected on this board which
may cause some issues in slave mode. I could not find any documentation
about this.
Keeping the chip in master mode after the reset helped to fix this
issue for me.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_WORD_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver fails to reset the camera or to set up control handlers, it
has to power the camera back off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This v4l2_subdev_internal_ops structure is never modified. All other
v4l2_subdev_internal_ops structures are declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value is not used after the assignment.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/i2c/adv7842.c:2400:27: warning: 'prim_mode_txt' defined but not used [-Wunused-const-variable=]
static const char * const prim_mode_txt[] = {
^~~~~~~~~~~~~
That seems to be useful for debug, and likely were used before.
While we could simply remove, let's comment it out, for now.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
