When tcp sends a TSO packet, adding a PSH flag on it
reduces the sojourn time of GRO packet in GRO receivers.
This is particularly the case under pressure, since RX queues
receive packets for many concurrent flows.
A sender can give a hint to GRO engines when it is
appropriate to flush a super-packet, especially when pacing
is in the picture, since next packet is probably delayed by
one ms.
Having less packets in GRO engine reduces chance
of LRU eviction or inflated RTT, and reduces GRO cost.
We found recently that we must not set the PSH flag on
individual full-size MSS segments [1] :
Under pressure (CWR state), we better let the packet sit
for a small delay (depending on NAPI logic) so that the
ACK packet is delayed, and thus next packet we send is
also delayed a bit. Eventually the bottleneck queue can
be drained. DCTCP flows with CWND=1 have demonstrated
the issue.
This patch allows to slowdown the aggregate traffic without
involving high resolution timers on senders and/or
receivers.
It has been used at Google for about four years,
and has been discussed at various networking conferences.
[1] segments smaller than MSS already have PSH flag set
by tcp_sendmsg() / tcp_mark_push(), unless MSG_MORE
has been requested by the user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a re-post of previous patch wrote by David Miller[1].
Phil Karn reported[2] that on busy networks with lots of unresolved
multicast routing entries, the creation of new multicast group routes
can be extremely slow and unreliable.
The reason is we hard-coded multicast route entries with unresolved source
addresses(cache_resolve_queue_len) to 10. If some multicast route never
resolves and the unresolved source addresses increased, there will
be no ability to create new multicast route cache.
To resolve this issue, we need either add a sysctl entry to make the
cache_resolve_queue_len configurable, or just remove cache_resolve_queue_len
limit directly, as we already have the socket receive queue limits of mrouted
socket, pointed by David.
>From my side, I'd perfer to remove the cache_resolve_queue_len limit instead
of creating two more(IPv4 and IPv6 version) sysctl entry.
[1] https://lkml.org/lkml/2018/7/22/11
[2] https://lkml.org/lkml/2018/7/21/343
v3: instead of remove cache_resolve_queue_len totally, let's only remove
the hard code limit when allocate the unresolved cache, as Eric Dumazet
suggested, so we don't need to re-count it in other places.
v2: hold the mfc_unres_lock while walking the unresolved list in
queue_count(), as Nikolay Aleksandrov remind.
Reported-by: Phil Karn <karn@ka9q.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_diag_get_aux_size() can be called with sockets in any state.
icsk_ulp_ops is only present for full sockets.
For SYN_RECV or TIME_WAIT ones we would access garbage.
Fixes: 61723b3932 ("tcp: ulp: add functions to dump ulp-specific information")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Luke Hsiao <lukehsiao@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
currently, only getsockopt(TCP_ULP) can be invoked to know if a ULP is on
top of a TCP socket. Extend idiag_get_aux() and idiag_get_aux_size(),
introduced by commit b37e88407c ("inet_diag: allow protocols to provide
additional data"), to report the ULP name and other information that can
be made available by the ULP through optional functions.
Users having CAP_NET_ADMIN privileges will then be able to retrieve this
information through inet_diag_handler, if they specify INET_DIAG_INFO in
the request.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This explicitly clarifies that bbr_bdp() returns the rounded-up value of
the bandwidth-delay product and why in the comments.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP associates tx timestamp requests with a byte in the bytestream.
If merging skbs in tcp_mtu_probe, migrate the tstamp request.
Similar to MSG_EOR, do not allow moving a timestamp from any segment
in the probe but the last. This to avoid merging multiple timestamps.
Tested with the packetdrill script at
https://github.com/wdebruij/packetdrill/commits/mtu_probe-1
Link: http://patchwork.ozlabs.org/patch/1143278/#2232897
Fixes: 4ed2d765df ("net-timestamp: TCP timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Rutsky reported stuck TCP sessions after memory pressure
events. Edge Trigger epoll() user would never receive an EPOLLOUT
notification allowing them to retry a sendmsg().
Jason tested the case of sk_stream_alloc_skb() returning NULL,
but there are other paths that could lead both sendmsg() and sendpage()
to return -1 (EAGAIN), with an empty skb queued on the write queue.
This patch makes sure we remove this empty skb so that
Jason code can detect that the queue is empty, and
call sk->sk_write_space(sk) accordingly.
Fixes: ce5ec44099 ("tcp: ensure epoll edge trigger wakeup when write queue is empty")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Reported-by: Vladimir Rutsky <rutsky@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An excerpt from netlink(7) man page,
In multipart messages (multiple nlmsghdr headers with associated payload
in one byte stream) the first and all following headers have the
NLM_F_MULTI flag set, except for the last header which has the type
NLMSG_DONE.
but, after (ee28906) there is a missing NLM_F_MULTI flag in the middle of a
FIB dump. The result is user space applications following above man page
excerpt may get confused and may stop parsing msg believing something went
wrong.
In the golang netlink lib [0] the library logic stops parsing believing the
message is not a multipart message. Found this running Cilium[1] against
net-next while adding a feature to auto-detect routes. I noticed with
multiple route tables we no longer could detect the default routes on net
tree kernels because the library logic was not returning them.
Fix this by handling the fib_dump_info_fnhe() case the same way the
fib_dump_info() handles it by passing the flags argument through the
call chain and adding a flags argument to rt_fill_info().
Tested with Cilium stack and auto-detection of routes works again. Also
annotated libs to dump netlink msgs and inspected NLM_F_MULTI and
NLMSG_DONE flags look correct after this.
Note: In inet_rtm_getroute() pass rt_fill_info() '0' for flags the same
as is done for fib_dump_info() so this looks correct to me.
[0] https://github.com/vishvananda/netlink/
[1] https://github.com/cilium/
Fixes: ee28906fd7 ("ipv4: Dump route exceptions if requested")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __icmp_send() there is a possibility that the rt->dst.dev is NULL,
e,g, with tunnel collect_md mode, which will cause kernel crash.
Here is what the code path looks like, for GRE:
- ip6gre_tunnel_xmit
- ip6gre_xmit_ipv4
- __gre6_xmit
- ip6_tnl_xmit
- if skb->len - t->tun_hlen - eth_hlen > mtu; return -EMSGSIZE
- icmp_send
- net = dev_net(rt->dst.dev); <-- here
The reason is __metadata_dst_init() init dst->dev to NULL by default.
We could not fix it in __metadata_dst_init() as there is no dev supplied.
On the other hand, the reason we need rt->dst.dev is to get the net.
So we can just try get it from skb->dev when rt->dst.dev is NULL.
v4: Julian Anastasov remind skb->dev also could be NULL. We'd better
still use dst.dev and do a check to avoid crash.
v3: No changes.
v2: fix the issue in __icmp_send() instead of updating shared dst dev
in {ip_md, ip6}_tunnel_xmit.
Fixes: c8b34e680a ("ip_tunnel: Add tnl_update_pmtu in ip_md_tunnel_xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable err is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused Value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it expects a unsigned int, but got a __be32
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in ip_mc_inc_group, memory allocation flag, not mcast mode, is expected
by __ip_mc_inc_group
similar issue in __ip_mc_join_group, both mcase mode and gfp_t are needed
here, so use ____ip_mc_inc_group(...)
Fixes: 9fb20801da ("net: Fix ip_mc_{dec,inc}_group allocation context")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer members of an object with static storage duration, if not
explicitly initialized, will be initialized to a NULL pointer. The
net namespace API checks if this pointer is not NULL before using it,
it are safe to remove the function.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Rename mss field to mss_option field in synproxy, from Fernando Mancera.
2) Use SYSCTL_{ZERO,ONE} definitions in conntrack, from Matteo Croce.
3) More strict validation of IPVS sysctl values, from Junwei Hu.
4) Remove unnecessary spaces after on the right hand side of assignments,
from yangxingwu.
5) Add offload support for bitwise operation.
6) Extend the nft_offload_reg structure to store immediate date.
7) Collapse several ip_set header files into ip_set.h, from
Jeremy Sowden.
8) Make netfilter headers compile with CONFIG_KERNEL_HEADER_TEST=y,
from Jeremy Sowden.
9) Fix several sparse warnings due to missing prototypes, from
Valdis Kletnieks.
10) Use static lock initialiser to ensure connlabel spinlock is
initialized on boot time to fix sched/act_ct.c, patch
from Florian Westphal.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
There is a small merge conflict in libbpf (Cc Andrii so he's in the loop
as well):
for (i = 1; i <= btf__get_nr_types(btf); i++) {
t = (struct btf_type *)btf__type_by_id(btf, i);
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
<<<<<<< HEAD
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t+1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && kind == BTF_KIND_DATASEC) {
=======
t->size = sizeof(int);
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 32);
} else if (!has_datasec && btf_is_datasec(t)) {
>>>>>>> 72ef80b5ee
/* replace DATASEC with STRUCT */
Conflict is between the two commits 1d4126c4e1 ("libbpf: sanitize VAR to
conservative 1-byte INT") and b03bc6853c ("libbpf: convert libbpf code to
use new btf helpers"), so we need to pick the sanitation fixup as well as
use the new btf_is_datasec() helper and the whitespace cleanup. Looks like
the following:
[...]
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && btf_is_datasec(t)) {
/* replace DATASEC with STRUCT */
[...]
The main changes are:
1) Addition of core parts of compile once - run everywhere (co-re) effort,
that is, relocation of fields offsets in libbpf as well as exposure of
kernel's own BTF via sysfs and loading through libbpf, from Andrii.
More info on co-re: http://vger.kernel.org/bpfconf2019.html#session-2
and http://vger.kernel.org/lpc-bpf2018.html#session-2
2) Enable passing input flags to the BPF flow dissector to customize parsing
and allowing it to stop early similar to the C based one, from Stanislav.
3) Add a BPF helper function that allows generating SYN cookies from XDP and
tc BPF, from Petar.
4) Add devmap hash-based map type for more flexibility in device lookup for
redirects, from Toke.
5) Improvements to XDP forwarding sample code now utilizing recently enabled
devmap lookups, from Jesper.
6) Add support for reporting the effective cgroup progs in bpftool, from Jakub
and Takshak.
7) Fix reading kernel config from bpftool via /proc/config.gz, from Peter.
8) Fix AF_XDP umem pages mapping for 32 bit architectures, from Ivan.
9) Follow-up to add two more BPF loop tests for the selftest suite, from Alexei.
10) Add perf event output helper also for other skb-based program types, from Allan.
11) Fix a co-re related compilation error in selftests, from Yonghong.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The current implementation of TCP MTU probing can considerably
underestimate the MTU on lossy connections allowing the MSS to get down to
48. We have found that in almost all of these cases on our networks these
paths can handle much larger MTUs meaning the connections are being
artificially limited. Even though TCP MTU probing can raise the MSS back up
we have seen this not to be the case causing connections to be "stuck" with
an MSS of 48 when heavy loss is present.
Prior to pushing out this change we could not keep TCP MTU probing enabled
b/c of the above reasons. Now with a reasonble floor set we've had it
enabled for the past 6 months.
The new sysctl will still default to TCP_MIN_SND_MSS (48), but gives
administrators the ability to control the floor of MSS probing.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from commit d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
loopback flows got hurt, because for each skb sent, the socket receives an
immediate ACK and sk_flush_backlog() causes extra work.
Intent was to not let the backlog grow too much, but we went a bit too far.
We can check the backlog every 16 skbs (about 1MB chunks)
to increase TCP over loopback performance by about 15 %
Note that the call to sk_flush_backlog() handles a single ACK,
thanks to coalescing done on backlog, but cleans the 16 skbs
found in rtx rb-tree.
Reported-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.
Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.
Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.
Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.
Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).
See commit 0608c69c9a ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.
v2:
- remove superfluous decrypted mark copy (Willem);
- remove the stale doc entry (Boris);
- rely entirely on EOR marking to prevent coalescing (Boris);
- use an internal sendpages flag instead of marking the socket
(Boris).
v3 (Willem):
- reorganize the can_skb_orphan_partial() condition;
- fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).
By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e334 ("Revert
"ipv4: use skb coalescing in defragmentation"")).
Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.
When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.
Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.
This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.
[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1
Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introduce "mss_encode" field in the synproxy_options struct the field
"mss" is a little confusing. It has been renamed to "mss_option".
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows generation of a SYN cookie before an SKB has been
allocated, as is the case at XDP.
Signed-off-by: Petar Penkov <ppenkov@google.com>
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This allows us to call this function before an SKB has been
allocated.
Signed-off-by: Petar Penkov <ppenkov@google.com>
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-07-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix segfault in libbpf, from Andrii.
2) fix gso_segs access, from Eric.
3) tls/sockmap fixes, from Jakub and John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the same checks introduced by commit cb9f1b7838
("ip: validate header length on virtual device xmit") for
ipip tunnel.
Fixes: cb9f1b7838 ("ip: validate header length on virtual device xmit")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a map free is called and in parallel a socket is closed we
have two paths that can potentially reset the socket prot ops, the
bpf close() path and the map free path. This creates a problem
with which prot ops should be used from the socket closed side.
If the map_free side completes first then we want to call the
original lowest level ops. However, if the tls path runs first
we want to call the sockmap ops. Additionally there was no locking
around prot updates in TLS code paths so the prot ops could
be changed multiple times once from TLS path and again from sockmap
side potentially leaving ops pointed at either TLS or sockmap
when psock and/or tls context have already been destroyed.
To fix this race first only update ops inside callback lock
so that TLS, sockmap and lowest level all agree on prot state.
Second and a ULP callback update() so that lower layers can
inform the upper layer when they are being removed allowing the
upper layer to reset prot ops.
This gets us close to allowing sockmap and tls to be stacked
in arbitrary order but will save that patch for *next trees.
v4:
- make sure we don't free things for device;
- remove the checks which swap the callbacks back
only if TLS is at the top.
Reported-by: syzbot+06537213db7ba2745c4a@syzkaller.appspotmail.com
Fixes: 02c558b2d5 ("bpf: sockmap, support for msg_peek in sk_msg with redirect ingress")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some applications set tiny SO_SNDBUF values and expect
TCP to just work. Recent patches to address CVE-2019-11478
broke them in case of losses, since retransmits might
be prevented.
We should allow these flows to make progress.
This patch allows the first and last skb in retransmit queue
to be split even if memory limits are hit.
It also adds the some room due to the fact that tcp_sendmsg()
and tcp_sendpage() might overshoot sk_wmem_queued by about one full
TSO skb (64KB size). Note this allowance was already present
in stable backports for kernels < 4.15
Note for < 4.15 backports :
tcp_rtx_queue_tail() will probably look like :
static inline struct sk_buff *tcp_rtx_queue_tail(const struct sock *sk)
{
struct sk_buff *skb = tcp_send_head(sk);
return skb ? tcp_write_queue_prev(sk, skb) : tcp_write_queue_tail(sk);
}
Fixes: f070ef2ac6 ("tcp: tcp_fragment() should apply sane memory limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Christoph Paasch <cpaasch@apple.com>
Cc: Jonathan Looney <jtl@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix a deadlock when module is requested via netlink_bind()
in nfnetlink, from Florian Westphal.
2) Fix ipt_rpfilter and ip6t_rpfilter with VRF, from Miaohe Lin.
3) Skip master comparison in SIP helper to fix expectation clash
under two valid scenarios, from xiao ruizhu.
4) Remove obsolete comments in nf_conntrack codebase, from
Yonatan Goldschmidt.
5) Fix redirect extension module autoload, from Christian Hesse.
6) Fix incorrect mssg option sent to client in synproxy,
from Fernando Fernandez.
7) Fix incorrect window calculations in TCP conntrack, from
Florian Westphal.
8) Don't bail out when updating basechain policy due to recent
offload works, also from Florian.
9) Allow symhash to use modulus 1 as other hash extensions do,
from Laura.Garcia.
10) Missing NAT chain module autoload for the inet family,
from Phil Sutter.
11) Fix missing adjustment of TCP RST packet in synproxy,
from Fernando Fernandez.
12) Skip EAGAIN path when nft_meta_bridge is built-in or
not selected.
13) Conntrack bridge does not depend on nf_tables_bridge.
14) Turn NF_TABLES_BRIDGE into tristate to fix possible
link break of nft_meta_bridge, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
Neal reported incorrect use of ns_capable() from bpf hook.
bpf_setsockopt(...TCP_CONGESTION...)
-> tcp_set_congestion_control()
-> ns_capable(sock_net(sk)->user_ns, CAP_NET_ADMIN)
-> ns_capable_common()
-> current_cred()
-> rcu_dereference_protected(current->cred, 1)
Accessing 'current' in bpf context makes no sense, since packets
are processed from softirq context.
As Neal stated : The capability check in tcp_set_congestion_control()
was written assuming a system call context, and then was reused from
a BPF call site.
The fix is to add a new parameter to tcp_set_congestion_control(),
so that the ns_capable() call is only performed under the right
context.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In a rare case where we redirect local packets from veth to lo,
these packets fail to pass the source validation when rp_filter
is turned on, as the tracing shows:
<...>-311708 [040] ..s1 7951180.957825: fib_table_lookup: table 254 oif 0 iif 1 src 10.53.180.130 dst 10.53.180.130 tos 0 scope 0 flags 0
<...>-311708 [040] ..s1 7951180.957826: fib_table_lookup_nh: nexthop dev eth0 oif 4 src 10.53.180.130
So, the fib table lookup returns eth0 as the nexthop even though
the packets are local and should be routed to loopback nonetheless,
but they can't pass the dev match check in fib_info_nh_uses_dev()
without this patch.
It should be safe to relax this check for this special case, as
normally packets coming out of loopback device still have skb_dst
so they won't even hit this slow path.
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now synproxy sends the mss value set by the user on client syn-ack packet
instead of the mss value that client announced.
Fixes: 48b1de4c11 ("netfilter: add SYNPROXY core/target")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In 9fb9cbb108 ("[NETFILTER]: Add nf_conntrack subsystem.") the new
generic nf_conntrack was introduced, and it came to supersede the old
ip_conntrack.
This change updates (some) of the obsolete comments referring to old
file/function names of the ip_conntrack mechanism, as well as removes a
few self-referencing comments that we shouldn't maintain anymore.
I did not update any comments referring to historical actions (e.g,
comments like "this file was derived from ..." were left untouched, even
if the referenced file is no longer here).
Signed-off-by: Yonatan Goldschmidt <yon.goldschmidt@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When conntracks change during a dialog, SDP messages may be sent from
different conntracks to establish expects with identical tuples. In this
case expects conflict may be detected for the 2nd SDP message and end up
with a process failure.
The fixing here is to reuse an existing expect who has the same tuple for a
different conntrack if any.
Here are two scenarios for the case.
1)
SERVER CPE
| INVITE SDP |
5060 |<----------------------|5060
| 100 Trying |
5060 |---------------------->|5060
| 183 SDP |
5060 |---------------------->|5060 ===> Conntrack 1
| PRACK |
50601 |<----------------------|5060
| 200 OK (PRACK) |
50601 |---------------------->|5060
| 200 OK (INVITE) |
5060 |---------------------->|5060
| ACK |
50601 |<----------------------|5060
| |
|<--- RTP stream ------>|
| |
| INVITE SDP (t38) |
50601 |---------------------->|5060 ===> Conntrack 2
With a certain configuration in the CPE, SIP messages "183 with SDP" and
"re-INVITE with SDP t38" will go through the sip helper to create
expects for RTP and RTCP.
It is okay to create RTP and RTCP expects for "183", whose master
connection source port is 5060, and destination port is 5060.
In the "183" message, port in Contact header changes to 50601 (from the
original 5060). So the following requests e.g. PRACK and ACK are sent to
port 50601. It is a different conntrack (let call Conntrack 2) from the
original INVITE (let call Conntrack 1) due to the port difference.
In this example, after the call is established, there is RTP stream but no
RTCP stream for Conntrack 1, so the RTP expect created upon "183" is
cleared, and RTCP expect created for Conntrack 1 retains.
When "re-INVITE with SDP t38" arrives to create RTP&RTCP expects, current
ALG implementation will call nf_ct_expect_related() for RTP and RTCP. The
expects tuples are identical to those for Conntrack 1. RTP expect for
Conntrack 2 succeeds in creation as the one for Conntrack 1 has been
removed. RTCP expect for Conntrack 2 fails in creation because it has
idential tuples and 'conflict' with the one retained for Conntrack 1. And
then result in a failure in processing of the re-INVITE.
2)
SERVER A CPE
| REGISTER |
5060 |<------------------| 5060 ==> CT1
| 200 |
5060 |------------------>| 5060
| |
| INVITE SDP(1) |
5060 |<------------------| 5060
| 300(multi choice) |
5060 |------------------>| 5060 SERVER B
| ACK |
5060 |<------------------| 5060
| INVITE SDP(2) |
5060 |-------------------->| 5060 ==> CT2
| 100 |
5060 |<--------------------| 5060
| 200(contact changes)|
5060 |<--------------------| 5060
| ACK |
5060 |-------------------->| 50601 ==> CT3
| |
|<--- RTP stream ---->|
| |
| BYE |
5060 |<--------------------| 50601
| 200 |
5060 |-------------------->| 50601
| INVITE SDP(3) |
5060 |<------------------| 5060 ==> CT1
CPE sends an INVITE request(1) to Server A, and creates a RTP&RTCP expect
pair for this Conntrack 1 (CT1). Server A responds 300 to redirect to
Server B. The RTP&RTCP expect pairs created on CT1 are removed upon 300
response.
CPE sends the INVITE request(2) to Server B, and creates an expect pair
for the new conntrack (due to destination address difference), let call
CT2. Server B changes the port to 50601 in 200 OK response, and the
following requests ACK and BYE from CPE are sent to 50601. The call is
established. There is RTP stream and no RTCP stream. So RTP expect is
removed and RTCP expect for CT2 retains.
As BYE request is sent from port 50601, it is another conntrack, let call
CT3, different from CT2 due to the port difference. So the BYE request will
not remove the RTCP expect for CT2.
Then another outgoing call is made, with the same RTP port being used (not
definitely but possibly). CPE firstly sends the INVITE request(3) to Server
A, and tries to create a RTP&RTCP expect pairs for this CT1. In current ALG
implementation, the RTCP expect for CT1 fails in creation because it
'conflicts' with the residual one for CT2. As a result the INVITE request
fails to send.
Signed-off-by: xiao ruizhu <katrina.xiaorz@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When firewalld is enabled with ipv4/ipv6 rpfilter, vrf
ipv4/ipv6 packets will be dropped. Vrf device will pass
through netfilter hook twice. One with enslaved device
and another one with l3 master device. So in device may
dismatch witch out device because out device is always
enslaved device.So failed with the check of the rpfilter
and drop the packets by mistake.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
If an app is playing tricks to reuse a socket via tcp_disconnect(),
bytes_acked/received needs to be reset to 0. Otherwise tcp_info will
report the sum of the current and the old connection..
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 0df48c26d8 ("tcp: add tcpi_bytes_acked to tcp_info")
Fixes: bdd1f9edac ("tcp: add tcpi_bytes_received to tcp_info")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 363887a2cd ("ipv4: Support multipath hashing on inner IP pkts
for GRE tunnel") supports multipath policy value of 2, Layer 3 or inner
Layer 3 if present, but it only considers inner IPv4. There is a use
case of IPv6 is tunneled by IPv4 GRE, thus add the ability to hash on
inner IPv6 addresses.
Fixes: 363887a2cd ("ipv4: Support multipath hashing on inner IP pkts for GRE tunnel")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ip_neigh_gw4() and ip_neigh_gw6() can return either a valid pointer
or an error pointer, but the code currently checks that the pointer is
not NULL.
Fix this by checking that the pointer is not an error pointer, as this
can result in a NULL pointer dereference [1]. Specifically, I believe
that what happened is that ip_neigh_gw4() returned '-EINVAL'
(0xffffffffffffffea) to which the offset of 'refcnt' (0x70) was added,
which resulted in the address 0x000000000000005a.
[1]
BUG: KASAN: null-ptr-deref in refcount_inc_not_zero_checked+0x6e/0x180
Read of size 4 at addr 000000000000005a by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.2.0-rc6-custom-reg-179657-gaa32d89 #396
Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
Call Trace:
<IRQ>
dump_stack+0x73/0xbb
__kasan_report+0x188/0x1ea
kasan_report+0xe/0x20
refcount_inc_not_zero_checked+0x6e/0x180
ipv4_neigh_lookup+0x365/0x12c0
__neigh_update+0x1467/0x22f0
arp_process.constprop.6+0x82e/0x1f00
__netif_receive_skb_one_core+0xee/0x170
process_backlog+0xe3/0x640
net_rx_action+0x755/0xd90
__do_softirq+0x29b/0xae7
irq_exit+0x177/0x1c0
smp_apic_timer_interrupt+0x164/0x5e0
apic_timer_interrupt+0xf/0x20
</IRQ>
Fixes: 5c9f7c1dfc ("ipv4: Add helpers for neigh lookup for nexthop")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
