PFC stats are only tabulated when PFC is enabled. However in IEEE
mode the ieee_pfc pfc_tc bits were not checked and the calculation
was aborted.
This results in statistics not being reported through ethtool and
possible a false Tx hang occurring when receiving pause frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the REQ and GNT bit in the eeprom control register (EECD).
This is required if the eeprom is to be accessed with auto read
EERD register.
After a cold reset this doesn't matter but if PBIST MAC test was
executed before booting, the register was left in a dirty state
(the 2 bits where set), which caused the read operation to time out
and returning 0.
Reference (page 312):
http://download.intel.com/design/network/manuals/316080.pdf
Reported-by: Aleksandar Igic <aleksandar.igic@dektech.com.au>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Like other supported (igp) PHYs, the driver needs to be able to force the
master/slave mode on 82577. Since the code is the same as what already
exists in the code flow for igp PHYs, move it to a new function to be
called for both flows.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With multiple cards is hard to figure out which port caused trouble
int the layer2 routines (e.g. got a timeout).
Now we have the informations in the log output.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer3 and the activation delay timer need to be independent.
If timer3 fires do not reqest power up we have to send only INFO 0.
Now layer1 pass TBR3 again.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certification test it is very useful to change the layer1
timer3 value on runtime.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be full preemptiv safe, we cannot handle a L2 timeout in the timer
context itself, we should do all actions via the D-channel thread.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some configs it was still not possible to unload the driver,
because the module use count was srewed up.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tei manager reports current layer 1 state on creation.
On state change it reports it to the socket interface.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.
So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: John Bishop <johnx.bishop@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the link flow control configuration so that we
correctly set the link flow control settings for DCB. Previously we would
have to call the fc_enable call 8 times, once for each packet buffer. If
we move that logic into the fc_enable call itself we can avoid multiple
unnecessary register writes.
This change also corrects an issue in which we were only shifting the water
marks for 82599 parts by 6 instead of 10. This was resulting in us only
using 1/16 of the packet buffer when flow control was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can avoid many of the forward declarations found in ixgbe_common.c by
just reordering things so this patch does that to help cleanup the code.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the calls to put_page with calls to __free_page.
Since the FCoE code is able to access order 1 pages I thought it would be a
good idea to change things over to using __free_pages since that is the
preferred approach for freeing pages.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that ixgbe_fc_autoneg is a void and always sets the
current_mode. Previously if the link was down we would return an error,
however there is no harm in simply treating a link down case as a case in
which autoneg simply failed. This allows us to rely on the return value of
the ixgbe_fc_enable call now since there should be no cases where it
returns an error that would normally be ignored.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change reorders the mapping of rings to q_vectors in the case that the
number of rings exceeds the number of q_vectors. Previously we would
allocate the first R/N queues to the first q_vector where R is the number
of rings and N is the number of q_vectors. Instead of doing this we can do
a better job of interleaving the rings to the CPUs by assigning every Nth
ring to the q_vector.
The below tables illustrate this change for the R = 16 N = 4 case.
Before patch After patch
q_vector: 0 1 2 3 0 1 2 3
Rings: 0 4 8 12 0 1 2 3
1 5 9 13 4 5 6 7
3 6 10 14 8 9 10 11
4 7 11 15 12 13 14 15
This should improve the performance for both DCB or ATR when the number of
rings exceeds the number of q_vectors allocated by the adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can track instances of where a packet was
dropped due to a packet being received when there are no DMA buffers
available in the ring.
For some reason this was only being enabled with RSC, however it makes
more sense to always have this feature on so that we can track any cases
where we might drop a buffer due to an Rx ring being full.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Version bump to 1.11.3-k.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIOH
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull second set of MFD fixes from Samuel Ortiz:
"This time we only have a one liner fixing an omap-usb build error."
* tag 'mfd-for-linus-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix build breakage in omap-usb-host.c
Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c7fz
-----END PGP SIGNATURE-----
Merge tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
* tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: ahci_platform: Add synopsys ahci controller in DT's compatible list
ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros
libata: init ata_print_id to 0
ahci: Detect Marvell 88SE9172 SATA controller
libata: skip old error history when counting probe trials
Pull i2c embedded fixes from Wolfram Sang:
"Here are some typical i2c driver bugfixes for 3.4. Missed clock
handling, improper timeout fixes, hardware wrokarounds... All
patches have been in linux-next for a few days, too."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: disable QUEUE when sending is done
i2c: mxs: handle spurious interrupt
i2c-eg20t: Modify MODULE_AUTHOR's email address
i2c-eg20t: change timeout value 50msec to 1000msec
i2c: tegra: Add delay before resetting the controller after NACK
i2c: pnx: Disable clk in suspend
Pull drm fixes from Dave Airlie:
"Just some regression fixes from Ben along with a variable that gcc
failed to spot is uninitialised."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: initialise has_optimus variable.
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
Pull networking fixes from David Miller:
1) Transfer padding was wrong for full-speed USB in ASIX driver, fix
from Ingo van Lil.
2) Propagate the negative packet offset fix into the PowerPC BPF JIT.
From Jan Seiffert.
3) dl2k driver's private ioctls were letting unprivileged tasks make
MII writes and other ugly bits like that. Fix from Jeff Mahoney.
4) Fix TX VLAN and RX packet drops in ucc_geth, from Joakim Tjernlund.
5) OOPS and network namespace fixes in IPVS from Hans Schillstrom and
Julian Anastasov.
6) Fix races and sleeping in locked context bugs in drop_monitor, from
Neil Horman.
7) Fix link status indication in smsc95xx driver, from Paolo Pisati.
8) Fix bridge netfilter OOPS, from Peter Huang.
9) L2TP sendmsg can return on error conditions with the socket lock
held, oops. Fix from Sasha Levin.
10) udp_diag should return meaningful values for socket memory usage,
from Shan Wei.
11) Eric Dumazet is so awesome he gets his own section:
Socket memory cgroup code (I never should have applied those
patches, grumble...) made erroneous changes to
sk_sockets_allocated_read_positive(). It was changed to
use percpu_counter_sum_positive (which requires BH disabling)
instead of percpu_counter_read_positive (which does not).
Revert back to avoid crashes and lockdep warnings.
Adjust the default tcp_adv_win_scale and tcp_rmem[2] values
to fix throughput regressions. This is necessary as a result
of our more precise skb->truesize tracking.
Fix SKB leak in netem packet scheduler.
12) New device IDs for various bluetooth devices, from Manoj Iyer,
AceLan Kao, and Steven Harms.
13) Fix command completion race in ipw2200, from Stanislav Yakovlev.
14) Fix rtlwifi oops on unload, from Larry Finger.
15) Fix hard_mtu when adjusting hard_header_len in smsc95xx driver.
From Stephane Fillod.
16) ehea driver registers it's IRQ before all the necessary state is
setup, resulting in crashes. Fix from Thadeu Lima de Souza
Cascardo.
17) Fix PHY connection failures in davinci_emac driver, from Anatolij
Gustschin.
18) Missing break; in switch statement in bluetooth's
hci_cmd_complete_evt(). Fix from Szymon Janc.
19) Fix queue programming in iwlwifi, from Johannes Berg.
20) Interrupt throttling defaults not being actually programmed into the
hardware, fix from Jeff Kirsher and Ying Cai.
21) TLAN driver SKB encoding in descriptor busted on 64-bit, fix from
Benjamin Poirier.
22) Fix blind status block RX producer pointer deref in TG3 driver, from
Matt Carlson.
23) Promisc and multicast are busted on ehea, fixes from Thadeu Lima de
Souza Cascardo.
24) Fix crashes in 6lowpan, from Alexander Smirnov.
25) tcp_complete_cwr() needs to be careful to not rewind the CWND to
ssthresh if ssthresh has the "infinite" value. Fix from Yuchung
Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
sungem: Fix WakeOnLan
tcp: change tcp_adv_win_scale and tcp_rmem[2]
net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg
drop_monitor: prevent init path from scheduling on the wrong cpu
usbnet: fix failure handling in usbnet_probe
usbnet: fix leak of transfer buffer of dev->interrupt
ucc_geth: Add 16 bytes to max TX frame for VLANs
net: ucc_geth, increase no. of HW RX descriptors
netem: fix possible skb leak
sky2: fix receive length error in mixed non-VLAN/VLAN traffic
sky2: propogate rx hash when packet is copied
net: fix two typos in skbuff.h
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
ixgbe: fix calling skb_put on nonlinear skb assertion bug
ixgbe: Fix a memory leak in IEEE DCB
igbvf: fix the bug when initializing the igbvf
smsc75xx: enable mac to detect speed/duplex from phy
smsc75xx: declare smsc75xx's MII as GMII capable
smsc75xx: fix phy interrupt acknowledge
smsc75xx: fix phy init reset loop
...
Fix OOPS seen in coretemp driver if the CPU core ID is too large
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=iNOt
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix OOPS seen in coretemp driver if the CPU core ID is too large"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Increase CPU core limit
hwmon: (coretemp) fix oops on cpu unplug
The idea here seems to be to get a 44bit DMA mask working and if this
fails it should fallback to a 32bit DMA mask. The dma_mask variable is
assigned once to 44bit and never updated. pci_set_dma_mask() and
pci_set_consistent_dma_mask() are both implemented as functions so there
is no evil macro which might update dma_mask. Looking at the assembly, I
see a call to dma_set_mask() followed by dma_supported() and then a jump
passed the second dma_set_mask(). The only way to get to second
dma_set_mask() call is by an error code in the first one.
So I hereby remove the check since it looks superfluous. Please ignore
the path if there is black magic involved.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPEAr13xx series of SoCs contain Synopsys AHCI SATA Controller which shares
ahci_platform driver with other controller versions.
This patch updates DT compatible list for ahci_platform. It also updates and
renames binding documentation to more generic name.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
#ifdef, #endif is not required in definition/usage of arasan_cf_pm_ops. So, move
this definition and its usage outside of them.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the
following differences:
-ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
-ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
-ata3: DUMMY
+ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
+ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
ata4: DUMMY
ata5: DUMMY
-ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
+ata6: DUMMY
+ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
The change of numbering comes from commit 85d6725b7c ("libata:
make ata_print_id atomic") that changed lines like
ap->print_id = ata_print_id++;
to
ap->print_id = atomic_inc_return(&ata_print_id);
As the latter behaves like ++ata_print_id, we must initialize
it to zero to start the numbering from one.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The Marvell 88SE9172 SATA controller (PCI ID 1b4b 917a) already worked
once it was detected, but was missing an ahci_pci_tbl entry.
Boot tested on a Gigabyte Z68X-UD3H-B3 motherboard.
Signed-off-by: Matt Johnson <johnso87@illinois.edu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit d902747("[libata] Add ATA transport class") introduced
ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared.
But ata_count_probe_trials_cb() didn't check this flag and it still
counts the old error history. So wrong probe trials count is returned
and it causes problem, for example, SATA link speed is slowed down from
3.0Gbps to 1.5Gbps.
Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb().
Cc: stable <stable@vger.kernel.org> # 2.6.37+
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames,
but doesnt say so in skb->truesize.
This makes very possible to exhaust kernel memory since these skb evade
normal socket memory accounting.
As struct ieee80211_hdr is going to be pulled before calling IP stack,
there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes.
alloc_skb() is ok in this driver, allowing more tailroom.
Pull beginning of frame in skb header, in the hope we can reuse order-1
pages in the driver immediately for small frames and reduce their
truesize to the minimum (linear skbs)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After this commit:
commit aacc1bea19
Author: Multanen, Eric W <eric.w.multanen@intel.com>
Date: Wed Mar 28 07:49:09 2012 +0000
ixgbe: driver fix for link flap
The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is
called. This results in the FCoE app user priority never getting set
and the driver will not configure the tx_rings correctly for FCoE
packets which use the SAN MTU and FCoE offloads.
We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also
check for FCoE application changes. Additionally, we can drop the
IEEE variants of get_dcb_app() because this path is never called
with the IEEE mode enabled.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was possible for shutdown to pull the rug out from other driver entry
points. Now we just grab the rtnl lock before taking everything apart.
Thanks to Hariharan for noticing this tight race condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Hariharan Nagarajan <hanagara@cisco.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the Physical Function (PF) resets after the VF has set jumbo
frame MTU then the VF jumbo frame is overwritten. Make sure the
VF driver always requests proper MTU size after reset
synchronization.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 10Gig controller is capable of linking at 100Mbits - add
support for reporting that link speed.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the 82573, ASPM L1 gets disabled wholesale so this special-case code
is not required. For the 82574 the previous patch does the same as for
the 82573, disabling L1 on the adapter. Thus, this code is no longer
required and can be removed.
Signed-off-by: Chris Boot <bootc@bootc.net>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ASPM on the 82574 causes trouble. Currently the driver disables L0s for
this NIC but only disables L1 if the MTU is >1500. This patch simply
causes L1 to be disabled regardless of the MTU setting.
Signed-off-by: Chris Boot <bootc@bootc.net>
Cc: "Wyborny, Carolyn" <carolyn.wyborny@intel.com>
Cc: Nix <nix@esperi.org.uk>
Link: https://lkml.org/lkml/2012/3/19/362
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, IPv6 extension header parsing was disabled for all devices
supported by e1000e when using packet split mode. However, as per a
silicon errata, only certain devices need this restriction and will need
to disable IPv6 extension header parsing for all modes.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For 82574 and 82583 devices, resolve an intermittent link issue where
the link negotiates to 100Mbps rather than 1Gbps when powering off the
PHY and powering on the PHY after several seconds.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the locked versions of the read/write PHY ops function pointers
often produces excessively long lines. Shorten these as is done with
the non-locked versions of the PHY register read/write functions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a known issue in the 82577 and 82578 device that can cause a hang
in the device hardware during traffic stress; the current workaround in the
driver is to disable transmit flow control by default. If the user enables
transmit flow control and the device hang occurs, provide a message in the
syslog suggesting to re-enable the workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While testing the TCP changes I had to fix an issue in order to be able to
load and unload the module.
The recent patch that added thermal sensor support added a use after free
bug on module unload with an 82598 adapter in the system. To resolve the
issue I have updated the code so that when we free the info_kobj we set it
back to NULL.
I suspect there are likely other bugs present, but I will leave that for
another patch that can undergo more testing.
I am submitting this directly to net-next since this fixes a fairly serious
bug that will lock up the ixgbe module until the system is rebooted.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up. Fixed by casting
gp->wake_on_lan to bool. Tested on an iBook G4.
Signed-off-by: Gerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An EEH error can cause the FW to trigger a flash debug dump.
Resetting the card while flash dump is in progress can cause it not to recover.
Wait for it to finish before letting EEH flow to reset the card.
Signed-off-by: Sathya Perla <Sathya.Perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sarveshwar Bandi <Sarveshwar.Bandi@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renders the interface view somewhat inconsistent from the Host OS POV
considering the rest of the interfaces are showing their respective speeds
based on the bandwidth assigned to them.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this compiler warning (on PowerPC) by not marking a parameter as
const:
drivers/net/ethernet/pasemi/pasemi_mac.c: In function 'pasemi_mac_replenish_rx_ring':
drivers/net/ethernet/pasemi/pasemi_mac.c:646:3: warning: passing argument 1 of 'netdev_alloc_skb' discards qualifiers from pointer target type
include/linux/skbuff.h:1706:31: note: expected 'struct net_device *' but argument is of type 'const struct net_device *'
Cc: Olof Johansson <olof@lixom.net>
Cc: Pradeep A. Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 30a5de7723 added
ability to use single MSI-X vector, but lack proper
handling for 57710/57711 HW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around. It
is needed due to the other EHCI core changes that went in way back in
3.4-rc1, so this driver will now properly handle suspend/resume, as it
was broken. The other one is a minor bugfix that resolves an warning
that people have been seeing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+hli8ACgkQMUfUDdst+ymGdgCeKYDYx5w2N+tmSy50kjDEhSQI
534AoK3+ZQUNsEyLU8ufLtNOyPrtIH3i
=5LmY
-----END PGP SIGNATURE-----
Merge tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around.
It is needed due to the other EHCI core changes that went in way back
in 3.4-rc1, so this driver will now properly handle suspend/resume, as
it was broken. The other one is a minor bugfix that resolves an
warning that people have been seeing."
* tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: ehci-tegra: remove redundant gpio_set_value
EHCI: update PM methods in ehci-tegra.c
This is a deadlock bugfix that was easy to hit, and that the vt layer lock
rework got wrong, so it reverts the logic back to the way it was in 3.3 and
earlier kernels to prevent problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+hlr4ACgkQMUfUDdst+ynGqwCfeaot2snAEoWi1qp1pU+4cAJn
8gwAoLaO//pVnVmUIplPMRtFr3tuUN/h
=z8wN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull a TTY fix from Greg Kroah-Hartman:
"This is a deadlock bugfix that was easy to hit, and that the vt layer
lock rework got wrong, so it reverts the logic back to the way it was
in 3.3 and earlier kernels to prevent problems."
* tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix deadlock on scroll-lock
This reverts commit a844adfd7b.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.
spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.
So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Kai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add used and signal guest in worker thread but did not poll the virtqueue
during the zero copy callback. This may lead the missing of adding and
signalling during zerocopy. Solve this by polling the virtqueue and let it
wakeup the worker during callback.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When a packet were fully copied in zerocopy, we don't wait for the DMA done to
mark the done flag, so after the packet were passed to lower device, we need to
add used and signal guest immediately.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, we restart tx polling unconditionally when sendmsg()
fails. This would cause unnecessary wakeups of vhost wokers and waste
cpu utlization when evil userspace(guest driver) is able to hit EFAULT or
EINVAL.
The polling is only needed when the socket send buffer were exceeded or not
enough memory. So fix this by restarting polling only when sendmsg() returns
EAGAIN/ENOBUFS.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When we want to disable vhost_net backend while there's a tx work, a possible
NULL pointer defernece may happen we we try to deference the vq->bufs after
vhost_net_set_backend() assign a NULL to it.
As suggested by Michael, fix this by checking the vq->bufs instead of
vhost_sock_zcopy().
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There're several reasons that the vectors need to be validated:
- Return error when caller provides vectors whose num is greater than UIO_MAXIOV.
- Linearize part of skb when userspace provides vectors grater than MAX_SKB_FRAGS.
- Return error when userspace provides vectors whose total length may exceed
- MAX_SKB_FRAGS * PAGE_SIZE.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current the SKBTX_DEV_ZEROCOPY is set unconditionally after
zerocopy_sg_from_iovec(), this would lead NULL pointer when macvtap
fails to build zerocopy skb because destructor_arg was not
initialized. Solve this by set this flag after the skb were built
successfully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When get_user_pages_fast() fails to get all requested pages, we could not use
kfree_skb() to free it as it has not been put in the skb fragments. So we need
to call put_page() instead.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the skb fragment were pinned/built from user pages, we should
account the page instead of length for truesize.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch fixes the offset calculation when building skb:
- offset1 were used as skb data offset not vector offset
- reset offset to zero only when we advance to next vector
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the user request for the number of VFs in the max_vfs parameter is
out of range then reset the value to the default value of zero. This
makes the behavior of the ixgbe driver the same as for the igb driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the host VMM administrator has set the virtual function device's
MAC address then also deny VF requests for MACVLAN filters.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Garrett, Robert <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our adapters have thermal data available, this patch exports
this data via hwmon sysfs interface.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some 82599 adapters contain thermal data that we can get to via
an i2c interface. These functions provide support to get at that
data. A following patch will export this data.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Secondary unicast and multicast addresses are added to the Receive
Address registers (RAR) for most parts supported by the driver. For
82579, there is only one actual RAR and a number of Shared Receive Address
registers (SHRAR) that are shared among the driver and f/w which can be
reserved and write-protected by the f/w. On this device, use the SHRARs
that are not taken by f/w for the additional addresses.
Add a MAC ops function pointer infrastructure (similar to other MAC
operations in the driver) for setting RARs, introduce a new rar_set
function for 82579 and convert the existing code that sets RARs on other
devices to a generic rar_set function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY initialization flows and assorted workarounds for 82577/8/9 done
during driver load and resume from Sx should be the same yet they are not.
Combine the current flows/workarounds into a common set of functions that
are called during the different code paths.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An update to the EEPROM on 82579 will extend a delay in hardware to fix an
issue with WoL not working after a G3->S5 transition which is unrelated to
the driver. However, this extended delay conflicts with nominal operation
of the device when it is initialized by the driver and after every reset
of the hardware (i.e. the driver starts configuring the device before the
hardware is done with it's own configuration work). The workaround for
when the driver is in control of the device is to tell the hardware after
every reset the configuration delay should be the original shorter one.
Some pre-existing variables are renamed generically to be re-used with
new register accesses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.
Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers. In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.
The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines. The driver now uses the standard dev_pm_ops methods instead
of legacy power management. Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).
These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core. The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately. Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing the locking accidentally replaced a race in the scroll
lock handling with a deadlock. Turn it back into a race for
now.
The basic problem is that there are two paths into the tty
stop/start helpers. One via the tty layer ^S/^Q handling
where we need to take the kbd_event_lock and one via the
special keyboard handler for fn_hold where we already hold
it. Probably we need to split out into a separate LED lock
but for now just go back to the race as it's a bit close
to release.
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
