commit 0653d50140 upstream.
The current modeset sequence can't handle port sync and bigjoiner
at the same time. Refuse port sync when bigjoiner is needed,
at least until we fix the modeset sequence.
v2: Add a FIXME (Vandite)
Cc: stable@vger.kernel.org
Tested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404213441.17637-4-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit b37e1347b9)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add encoder vfuncs for audio enable/disable. This will allow
audio to be enabled/disabled during fastsets. An encoder hook
is necessary as on pre-hsw platforms different encoder types
implement audio in different ways.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-9-ville.syrjala@linux.intel.com
Push the audio enable/disable to be the last/first thing
respectively that is done in the encoder enable/disable hooks.
The goal is to move it further out of these encoder hooks entirely.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-5-ville.syrjala@linux.intel.com
At least a Realtek DP branch device with the
OUI 00-e0-4c dev-ID Dp1.4 HW-rev 1.0 SW-rev 131.1
device identification doesn't report detecting the FEC decoding start
symbol. Tune down the corresponding error to a debug message.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113142051.258864-1-imre.deak@intel.com
TRANS_DP2_CTL register is programmed to enable panel replay from source
and sink is enabled through panel replay dpcd configuration address.
Bspec: 1407940617
v1: Initial version.
v2:
- Use pr_* flags instead psr_* flags. [Jouni]
- Remove intel_dp_is_edp check as edp1.5 also has panel replay. [Jouni]
v3: Cover letter updated and selective fetch condition check is added
before updating its bit in PSR2_MAN_TRK_CTL register. [Jouni]
v4: Selective fetch related PSR2_MAN_TRK_CTL programmming dropped. [Jouni]
v5: Added PSR2_MAN_TRK_CTL programming as needed for Continuous Full
Frame (CFF) update.
v6: Rebased on latest.
Note: Initial plan is to enable panel replay in full-screen live active
frame update mode. In a incremental approach panel replay will be enabled
in selctive update mode if there is any gap in curent implementation.
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231108072303.3414118-6-animesh.manna@intel.com
Enable DSC using the DSC AUX device stored for this purpose in the
connector. For clarity add separate functions to enable/disable the
decompression, since these sequences will diverge more in follow-up
patches that also enable/disable DSC passthrough and on MST do the
actual enabling/disabling only for the first/last user of the given
AUX device. As a preparation for the latter refcounting change, also
pass the atomic state to the functions.
While at it set/clear only the DP_DECOMPRESSION_EN flag in the
DP_DSC_ENABLE DPCD register, preserving the reserved register bits.
Besides preserving the reserved register bits, the behavior stays as
before, as DSC is still only enabled for the first MST stream (which a
follow-up patch changes, enabling it for all streams).
v2:
- Add a helper function setting/clearing the decompression flag,
preserving the reserved register bits.
v3:
- Add separate functions to enable/disable decompression and pass the
atomic state to these.
- Add DocBook for both functions.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-24-imre.deak@intel.com
Enable/disable the DSC decompression in the sink/branch from the MST
encoder hooks. This prepares for an upcoming patch toggling DSC for each
stream as needed, but for now keeps the current behavior, as DSC is only
enabled for the first MST stream.
v2:
- Rebased on latest drm-tip.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-5-imre.deak@intel.com
As required by the DP standard wait for the sink to detect the FEC
decode enabling symbol sent by the source.
There is a difference between SST and MST when the source enables
the FEC encoding: on SST this happens only after enabling the
transcoder, whereas on MST it happens already after enabling the
transcoder function (before enabling the transcoder). Wait for the
detected status at the earliest spot accordingly.
v2:
- Wait for the FEC detected status on SST after the transcoder is
enabled.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-20-imre.deak@intel.com
Atm the DSC PPS SDP is programmed only if the first stream is compressed
and then it's programmed only for the first stream. This left all other
compressed streams blank. Program the SDP for all streams.
v2:
- Rebase on upstream include "intel_vdsc.h" change.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-3-imre.deak@intel.com
Let's convert intel_hdcp_enable to a blanket function
which just has some conditions which needs to be checked
before connectors enable hdcp.
This cleans up code and avoids code duplication.
--v3
-Keep function name as intel_hdcp_enable() [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231026121139.987437-3-suraj.kandpal@intel.com
intel_cx0_phy.[ch] should contain the details about C10/C20, not leaking
it to the rest of the driver. Start abstracting this by exporting a
single PLL hw readout that handles the differences between C20 and C10
internally to that compilation unit.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018222831.4132968-2-lucas.demarchi@intel.com
Remove redundant intel_connector NULL check. Having it here just
creates further confusion and also the variable already gets
dereferenced before the aforementioned NULL check
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006072830.581487-1-suraj.kandpal@intel.com
Rename the various names we've used for the DDC bus
i2c adapter ("i2c", "adapter", etc.) to just "ddc".
This differentiates it from the various other i2c
busses we might have (DSI panel stuff, DVO control bus, etc.).
v2: Don't add a bogus drm_get_edid() call (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230831104300.29688-1-ville.syrjala@linux.intel.com
Track DP enhanced framing properly in the crtc state instead
of relying just on the cached DPCD everywhere, and hook it
up into the state check and dump.
v2: Actually set enhanced_framing in .compute_config()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503113659.16305-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
By at least strong convention, a print-buffer's trailing newline says
"message complete, send it". The exception (no TNL, followed by a call
to pr_cont) proves the general rule.
Most DRM.debug calls already comport with this: 207 DRM_DEV_DEBUG,
1288 drm_dbg. Clean up the remainders, in maintainer sized chunks.
No functional changes.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo changed subject while pushing]
Link: https://patchwork.freedesktop.org/patch/msgid/20230903184607.272198-4-jim.cromie@gmail.com
Try to deal with duplicate child devices for the same DDI port
by attempting to initialize them in VBT defined order The first
on to succeed for a specific DDI port will be the one we use.
We'll also get rid of i915->display.vbt.ports[] here as any conflicts
will now be handled at encoder registration time rather than during
VBT parsing. Note that intel_bios_encoder_data_lookup() still remaims
for pre-DDI DP/HDMI ports as those don't (at least yet) use VBT
driven initialization.
TODO: DSI dual link handling is sketchy at best
v2: Leave intel_bios_encoder_port() to the encoder callback (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230630155846.29931-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Stop with the VBT AUX CH sanitation, and instead just check
that the appropriate AUX CH is still available when initializing
a DP/TC port.
The reason being that we want to start initializing ports in
VBT order to deal with VBTs that declare child devices with
seemingly conflicting ports. As the encoder initialization can
fail for other reasons (at least for eDP+AUX) we can't know
upfront which way the conflicts should be resolved.
Note that the old way of sanitizing gave priority to the last
port declared in the VBT, but now we sort of do the opposite by
favoring the first encoder to successfully initialize. The reason
for the old "last port wins" preference was eg. Asrock B250M-HDV
where port A (eDP) and port E (DP->VGA) have an AUX CH conflict
and we need to prefer port E. However with the new way port A (eDP)
will be probed first, but will fail to probe due to HPD and thus
port E will still win in the end.
v2: Pimp the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230630155846.29931-5-ville.syrjala@linux.intel.com
Mixing VBT based AUX CH with platform defaults seems like
a recipe for conflicts. Let's only populate AUX CH if we
absolutely need it, that is only if we are dealing with
a DP output or a TC port (which need it due to some power
well shenanigans).
TODO: double check that real VBTs do in fact populate
the AUX CH for HDMI TC legacy ports...
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230630155846.29931-3-ville.syrjala@linux.intel.com
Make HSW/BDW use port_mask for output probing as well.
To achieve that the strap checks are moved into
intel_ddi_init() itself. Or should we move them to the
runtime port_mask init instead? Maybe not since the hardware
is still there, just not connected to anything.
v2: Account for DDI-E in strap detection
Keep to the old CRT->DDI init order
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-8-ville.syrjala@linux.intel.com
Sprinkle some asserts to catch any mishaps in the port_mask
vs. output init.
For DDI/DP/HDMI/SDVO I decided that we want to bail out for
an invalid port since those are the encoder types where
we might want consider driving the whole thing from the VBT
child device list, and bogus VBTs could be a real issue
(if for no other reason than the i915.vbt_firmware).
For DVO and HSW/BDW CRT port I just threw the assert in
there for good measure.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-5-ville.syrjala@linux.intel.com
If the output on a DP-alt link with its sink disconnected is kept
enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout
will cause havoc on the PCI bus, at least for other GFX devices on it
which will stop powering up. Since user space is not guaranteed to do a
disabling modeset in time, switch such disconnected but active links to
TBT mode - which is without such shortcomings - with a 2 second delay.
If the above condition is detected already during the driver load/system
resume sanitization step disable the output instead, as at that point no
user space or kernel client depends on a consistent output state yet and
because subsequent atomic modeset on such connectors - without the
actual sink capabilities available - can fail.
An active/disconnected port as above will also block the HPD status of
other active/disconnected ports to get updated (stuck in the connected
state), until the former port is disabled, its PHY is disconnected and
a ~10 ms delay has elapsed. This means the link state for all TypeC
ports/CRTCs must be rechecked after a CRTC is disabled due to the above
reason. For this disconnect the PHY synchronously after the CRTC/port is
disabled and recheck all CRTCs for the above condition whenever such a
port is disabled.
To account for a race condition during driver loading where the sink is
disconnected after the above sanitization step and before the HPD
interrupts get enabled, do an explicit check/link reset if needed from
the encoder's late_register hook, which is called after the HPD
interrupts are enabled already.
v2:
- Handle an active/disconnected port blocking the HPD state update of
another active/disconnected port.
- Cancel the delayed work resetting the link also from the encoder
enable/suspend/shutdown hooks.
- Rebase on the earlier intel_modeset_lock_ctx_retry() addition,
fixing here the missed atomic state reset in case of a retry.
- Fix handling of an error return from intel_atomic_get_crtc_state().
- Recheck if the port needs to be reset after all the atomic state
is locked and async commits are waited on.
v3:
- Add intel_crtc_needs_link_reset(), instead of open-coding it,
keep intel_crtc_has_encoders(). (Ville)
- Fix state dumping and use a bitmask to track disabled CRTCs in
intel_sanitize_all_crtcs(). (Ville)
- Set internal in intel_atomic_state right after allocating it.
(Ville)
- Recheck all CRTCs (not yet force-disabled) after a CRTC is
force-disabled for any reason (not only due to a link state)
in intel_sanitize_all_crtcs().
- Reduce delay after CRTC disabling to 20ms, and use the simpler
msleep().
- Clarify code comment about HPD behaviour in
intel_sanitize_all_crtcs().
- Move all the TC link reset logic to intel_tc.c .
- Cancel the link reset work synchronously during system suspend,
driver unload and shutdown.
v4:
- Rebased on previous patch, which allows calling the TC port
suspend/cleanup handlers without modeset locks held; remove the
display driver suspended assert from the link reset work
accordingly.
v5: (Ville)
- Remove reset work canceling from intel_ddi_pre_pll_enable().
- Track a crtc vs. pipe mask in intel_sanitize_all_crtcs().
- Add reset_link_commit() to clarify the
intel_modeset_lock_ctx_retry loop.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com
Call the TypeC port flush_work and cleanup handlers without the modeset
locks held. These don't require the locks, as the work takes - as it
should be able to at any point in time - any locks it needs and by the
time cleanup is called and after cleanup returns the encoder is not in
use.
This is required by the next patch canceling a TypeC port work
synchronously during encoder suspend and shutdown, where the work can
take modeset locks as well, hence the canceling must be done without
holding the locks.
I also considered moving the modeset locking down to each encoder
suspend()/shutdown() hook instead, however locking the full modeset
state for each encoder separately would be odd, and the bigger change -
affecting all encoders - is beyond the scope of this patchset.
v2:
- Add a TODO: comment to remove modeset locks if no encoder depends
on this. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-1-imre.deak@intel.com
This patch simplifying the handling of modeset locks and atomic state
for an atomic commit is based on
https://lore.kernel.org/all/20210715184954.7794-2-ville.syrjala@linux.intel.com/
adding the helper to i915. I find this approach preferrable than
open-coding the corresponding steps (fixed for me an atomic
state reset during a DEADLK retry, which I missed in the open-coded
version) and also better than the existing
DRM_MODESET_LOCK_ALL_BEGIN/END macros for the reasons described in the
above original patchset.
This change takes the helper into use only for atomic commits during DDI
hotplug handling, as a preparation for a follow-up patch adding a
similar commit started from the same spot. Other places doing a
driver-internal atomic commit is to be converted by a follow-up
patchset.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-13-imre.deak@intel.com
Pass all the parameter in intel_encoder->enable()
to intel_hdcp_enable as we need intel_atomic_state
later down to get acquire_ctx.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515103225.688830-2-suraj.kandpal@intel.com
We'll be wanting to compute has_hdmi_sink a bit differently
for some platforms. To that end compute it in the encoder
.compute_config_hook() before we call intel_hdmi_compute_config().
intel_hdmi_compute_has_hdmi_sink() will do the basic lifting
beyond any platform specific stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107194604.15227-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
As we already do with C10 chip, let's dump the pll
hw state for C20 as well.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-4-mika.kahola@intel.com
Create a table for C20 DP1.4, DP2.0 and HDMI2.1 rates.
The PLL settings are based on table, not for algorithmic alternative.
For DP 1.4 only MPLLB is in use.
Once register settings are done, we read back C20 HW state.
BSpec: 64568
v2: Updated pll tables (RK)
MPLLB selection fix (RK)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-3-mika.kahola@intel.com
C20 phy PLL programming sequence for DP, DP2.0, HDMI2.x non-FRL and
HDMI2.x FRL. This enables C20 MPLLA and MPLLB programming sequence. add
4 lane support for c20.
v2: Add 6.48Gbps and 6.75Gbps modes for eDP (RK)
Fix lane check (RK)
Fix multiline commenting (Arun)
use usleep_range() instead of msleep() (Andi)
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-2-mika.kahola@intel.com
Ville Syrjälä