Refactor get_inode_info() to populate all wanted fields on an output
structure. Besides, also introduce a helper function called
get_inode_gen(), which is commonly used.
Reviewed-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Preserve the fs-verity status of a btrfs file across send/recv.
There is no facility for installing the Merkle tree contents directly on
the receiving filesystem, so we package up the parameters used to enable
verity found in the verity descriptor. This gives the receive side
enough information to properly enable verity again. Note that this means
that receive will have to re-compute the whole Merkle tree, similar to
how compression worked before encoded_write.
Since the file becomes read-only after verity is enabled, it is
important that verity is added to the send stream after any file writes.
Therefore, when we process a verity item, merely note that it happened,
then actually create the command in the send stream during
'finish_inode_if_needed'.
This also creates V3 of the send stream format, without any format
changes besides adding the new commands and attributes.
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
After the patch "btrfs: send: fix sending link commands for existing file
paths", we now have two infrastructures to detect and eliminate duplicated
inode references (due to names that got removed and re-added between the
send and parent snapshots):
1) One that works on a single inode ref/extref item;
2) A new one that works acrosss all ref/extref items for an inode, and
it's also more efficient because even in the single ref/extref item
case, it does not do a linear search for all the names encoded in the
ref/extref item, it uses red black trees to speedup up the search.
There's no good reason to keep both infrastructures, we can use the new
one everywhere, and it's always more efficient.
So remove the old infrastructure and change all sites that are using it
to use the new one.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There is a bug sending link commands for existing file paths. When we're
processing an inode, we go over all references. All the new file paths are
added to the "new_refs" list. And all the deleted file paths are added to
the "deleted_refs" list. In the end, when we finish processing the inode,
we iterate over all the items in the "new_refs" list and send link commands
for those file paths. After that, we go over all the items in the
"deleted_refs" list and send unlink commands for them. If there are
duplicated file paths in both lists, we will try to create them before we
remove them. Then the receiver gets an -EEXIST error when trying the link
operations.
Example for having duplicated file paths in both list:
$ btrfs subvolume create vol
# create a file and 2000 hard links to the same inode
$ touch vol/foo
$ for i in {1..2000}; do link vol/foo vol/$i ; done
# take a snapshot for a parent snapshot
$ btrfs subvolume snapshot -r vol snap1
# remove 2000 hard links and re-create the last 1000 links
$ for i in {1..2000}; do rm vol/$i; done;
$ for i in {1001..2000}; do link vol/foo vol/$i; done
# take another one for a send snapshot
$ btrfs subvolume snapshot -r vol snap2
$ mkdir receive_dir
$ btrfs send snap2 -p snap1 | btrfs receive receive_dir/
At subvol snap2
link 1238 -> foo
ERROR: link 1238 -> foo failed: File exists
In this case, we will have the same file paths added to both lists. In the
parent snapshot, reference paths {1..1237} are stored in inode references,
but reference paths {1238..2000} are stored in inode extended references.
In the send snapshot, all reference paths {1001..2000} are stored in inode
references. During the incremental send, we process their inode references
first. In record_changed_ref(), we iterate all its inode references in the
send/parent snapshot. For every inode reference, we also use find_iref() to
check whether the same file path also appears in the parent/send snapshot
or not. Inode references {1238..2000} which appear in the send snapshot but
not in the parent snapshot are added to the "new_refs" list. On the other
hand, Inode references {1..1000} which appear in the parent snapshot but
not in the send snapshot are added to the "deleted_refs" list. Next, when
we process their inode extended references, reference paths {1238..2000}
are added to the "deleted_refs" list because all of them only appear in the
parent snapshot. Now two lists contain items as below:
"new_refs" list: {1238..2000}
"deleted_refs" list: {1..1000}, {1238..2000}
Reference paths {1238..2000} appear in both lists. And as the processing
order mentioned about before, the receiver gets an -EEXIST error when trying
the link operations.
To fix the bug, the idea is to process the "deleted_refs" list before
the "new_refs" list. However, it's not easy to reshuffle the processing
order. For one reason, if we do so, we may unlink all the existing paths
first, there's no valid path anymore for links. And it's inefficient
because we do a bunch of unlinks followed by links for the same paths.
Moreover, it makes less sense to have duplications in both lists. A
reference path cannot not only be regarded as new but also has been seen in
the past, or we won't call it a new path. However, it's also not a good
idea to make find_iref() check a reference against all inode references
and all inode extended references because it may result in large disk
reads.
So we introduce two rbtrees to make the references easier for lookups.
And we also introduce record_new_ref_if_needed() and
record_deleted_ref_if_needed() for changed_ref() to check and remove
duplicated references early.
Reviewed-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Introduce wrappers to allocate and free recorded_ref structures.
Reviewed-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are file attributes inherited from previous ext2 SETFLAGS/GETFLAGS
and later from XFLAGS interfaces, now commonly found under the
'fileattr' API. This corresponds to the individual inode bits and that's
part of the on-disk format, so this is suitable for the protocol. The
other interfaces contain a lot of cruft or bits that btrfs does not
support yet.
Currently the value is u64 and matches btrfs_inode_item. Not all the
bits can be set by ioctls (like NODATASUM or READONLY), but we can send
them over the protocol and leave it up to the receiving side what and
how to apply.
As some of the flags, eg. IMMUTABLE, can prevent any further changes,
the receiving side needs to understand that and apply the changes in the
right order, or possibly with some intermediate steps. This should be
easier, future proof and simpler on the protocol layer than implementing
in kernel.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When send v1 was introduced the otime (inode creation time) was not
available, however the attribute in btrfs send protocol exists. Though
it would be possible to add it for v1 too as the attribute would be
ignored by v1 receive, let's not change the layout of v1 and only add
that to v2+. The otime cannot be changed and is only informative.
Signed-off-by: David Sterba <dsterba@suse.com>
The whole send operation is restartable and handling properly a buffer
write may not be easy. We can't know what caused that and if a short
delay and retry will fix it or how many retries should be performed in
case it's a temporary condition.
The error value is returned to the ioctl caller so in case it's
transient problem, the user would be notified about the reason. Remove
the TODO note as there's no plan to handle ERESTARTSYS.
Signed-off-by: David Sterba <dsterba@suse.com>
Now that the new support is implemented, allow the ioctl to accept v2
and the compressed flag, and update the version in sysfs.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that all of the pieces are in place, we can use the ENCODED_WRITE
command to send compressed extents when appropriate.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For encoded writes in send v2, we will get the encoded data with
btrfs_encoded_read_regular_fill_pages(), which expects a list of raw
pages. To avoid extra buffers and copies, we should read directly into
the send buffer. Therefore, we need the raw pages for the send buffer.
We currently allocate the send buffer with kvmalloc(), which may return
a kmalloc'd buffer or a vmalloc'd buffer. For vmalloc, we can get the
pages with vmalloc_to_page(). For kmalloc, we could use virt_to_page().
However, the buffer size we use (144K) is not a power of two, which in
theory is not guaranteed to return a page-aligned buffer, and in
practice would waste a lot of memory due to rounding up to the next
power of two. 144K is large enough that it usually gets allocated with
vmalloc(), anyways. So, for send v2, replace kvmalloc() with vmalloc()
and save the pages in an array.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The length field of the send stream TLV header is 16 bits. This means
that the maximum amount of data that can be sent for one write is 64K
minus one. However, encoded writes must be able to send the maximum
compressed extent (128K) in one command, or more. To support this, send
stream version 2 encodes the DATA attribute differently: it has no
length field, and the length is implicitly up to the end of containing
command (which has a 32bit length field). Although this is necessary
for encoded writes, normal writes can benefit from it, too.
Also add a check to enforce that the DATA attribute is last. It is only
strictly necessary for v2, but we might as well make v1 consistent with
it.
For v2, let's bump up the send buffer to the maximum compressed extent
size plus 16K for the other metadata (144K total). Since this will most
likely be vmalloc'd (and always will be after the next commit), we round
it up to the next page since we might as well use the rest of the page
on systems with >16K pages.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This adds the definitions of the new commands for send stream version 2
and their respective attributes: fallocate, FS_IOC_SETFLAGS (a.k.a.
chattr), and encoded writes. It also documents two changes to the send
stream format in v2: the receiver shouldn't assume a maximum command
size, and the DATA attribute is encoded differently to allow for writes
larger than 64k. These will be implemented in subsequent changes, and
then the ioctl will accept the new version and flag.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit e77fbf9903 ("btrfs: send: prepare for v2 protocol") added
_BTRFS_SEND_C_MAX_V* macros equal to the maximum command number for the
version plus 1, but as written this creates gaps in the number space.
The maximum command number is currently 22, and __BTRFS_SEND_C_MAX_V1 is
accordingly 23. But then __BTRFS_SEND_C_MAX_V2 is 24, suggesting that v2
has a command numbered 23, and __BTRFS_SEND_C_MAX is 25, suggesting that
23 and 24 are valid commands.
Instead, let's explicitly number all of the commands, attributes, and
sentinel MAX constants.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We collect these statistics but have never exposed them in any way. I
also didn't find any patches that ever attempted to make use of them.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=/47A
-----END PGP SIGNATURE-----
Merge tag 'for-5.19-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs reverts from David Sterba:
"Due to a recent report [1] we need to revert the radix tree to xarray
conversion patches.
There's a problem with sleeping under spinlock, when xa_insert could
allocate memory under pressure. We use GFP_NOFS so this is a real
problem that we unfortunately did not discover during review.
I'm sorry to do such change at rc6 time but the revert is IMO the
safer option, there are patches to use mutex instead of the spin locks
but that would need more testing. The revert branch has been tested on
a few setups, all seem ok.
The conversion to xarray will be revisited in the future"
Link: https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/ [1]
* tag 'for-5.19-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Revert "btrfs: turn delayed_nodes_tree into an XArray"
Revert "btrfs: turn name_cache radix tree into XArray in send_ctx"
Revert "btrfs: turn fs_info member buffer_radix into XArray"
Revert "btrfs: turn fs_roots_radix in btrfs_fs_info into an XArray"
This reverts commit 4076942021.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
[1] https://lore.kernel.org/linux-btrfs/cover.1657097693.git.fdmanana@suse.com/
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
- Appoint myself page cache maintainer
- Fix how scsicam uses the page cache
- Use the memalloc_nofs_save() API to replace AOP_FLAG_NOFS
- Remove the AOP flags entirely
- Remove pagecache_write_begin() and pagecache_write_end()
- Documentation updates
- Convert several address_space operations to use folios:
- is_dirty_writeback
- readpage becomes read_folio
- releasepage becomes release_folio
- freepage becomes free_folio
- Change filler_t to require a struct file pointer be the first argument
like ->read_folio
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEejHryeLBw/spnjHrDpNsjXcpgj4FAmKNMDUACgkQDpNsjXcp
gj4/mwf/bpHhXH4ZoNIvtUpTF6rZbqeffmc0VrbxCZDZ6igRnRPglxZ9H9v6L53O
7B0FBQIfxgNKHZpdqGdOkv8cjg/GMe/HJUbEy5wOakYPo4L9fZpHbDZ9HM2Eankj
xBqLIBgBJ7doKr+Y62DAN19TVD8jfRfVtli5mqXJoNKf65J7BkxljoTH1L3EXD9d
nhLAgyQjR67JQrT/39KMW+17GqLhGefLQ4YnAMONtB6TVwX/lZmigKpzVaCi4r26
bnk5vaR/3PdjtNxIoYvxdc71y2Eg05n2jEq9Wcy1AaDv/5vbyZUlZ2aBSaIVbtKX
WfrhN9O3L0bU5qS7p9PoyfLc9wpq8A==
=djLv
-----END PGP SIGNATURE-----
Merge tag 'folio-5.19' of git://git.infradead.org/users/willy/pagecache
Pull page cache updates from Matthew Wilcox:
- Appoint myself page cache maintainer
- Fix how scsicam uses the page cache
- Use the memalloc_nofs_save() API to replace AOP_FLAG_NOFS
- Remove the AOP flags entirely
- Remove pagecache_write_begin() and pagecache_write_end()
- Documentation updates
- Convert several address_space operations to use folios:
- is_dirty_writeback
- readpage becomes read_folio
- releasepage becomes release_folio
- freepage becomes free_folio
- Change filler_t to require a struct file pointer be the first
argument like ->read_folio
* tag 'folio-5.19' of git://git.infradead.org/users/willy/pagecache: (107 commits)
nilfs2: Fix some kernel-doc comments
Appoint myself page cache maintainer
fs: Remove aops->freepage
secretmem: Convert to free_folio
nfs: Convert to free_folio
orangefs: Convert to free_folio
fs: Add free_folio address space operation
fs: Convert drop_buffers() to use a folio
fs: Change try_to_free_buffers() to take a folio
jbd2: Convert release_buffer_page() to use a folio
jbd2: Convert jbd2_journal_try_to_free_buffers to take a folio
reiserfs: Convert release_buffer_page() to use a folio
fs: Remove last vestiges of releasepage
ubifs: Convert to release_folio
reiserfs: Convert to release_folio
orangefs: Convert to release_folio
ocfs2: Convert to release_folio
nilfs2: Remove comment about releasepage
nfs: Convert to release_folio
jfs: Convert to release_folio
...
A send operation reads extent data using the buffered IO path for getting
extent data to send in write commands and this is both because it's simple
and to make use of the generic readahead infrastructure, which results in
a massive speedup.
However this fills the page cache with data that, most of the time, is
really only used by the send operation - once the write commands are sent,
it's not useful to have the data in the page cache anymore. For large
snapshots, bringing all data into the page cache eventually leads to the
need to evict other data from the page cache that may be more useful for
applications (and kernel subsystems).
Even if extents are shared with the subvolume on which a snapshot is based
on and the data is currently on the page cache due to being read through
the subvolume, attempting to read the data through the snapshot will
always result in bringing a new copy of the data into another location in
the page cache (there's currently no shared memory for shared extents).
So make send evict the data it has read before if when it first opened
the inode, its mapping had no pages currently loaded: when
inode->i_mapping->nr_pages has a value of 0. Do this instead of deciding
based on the return value of filemap_range_has_page() before reading an
extent because the generic readahead mechanism may read pages beyond the
range we request (and it very often does it), which means a call to
filemap_range_has_page() will return true due to the readahead that was
triggered when processing a previous extent - we don't have a simple way
to distinguish this case from the case where the data was brought into
the page cache through someone else. So checking for the mapping number
of pages being 0 when we first open the inode is simple, cheap and it
generally accomplishes the goal of not trashing the page cache - the
only exception is if part of data was previously loaded into the page
cache through the snapshot by some other process, in that case we end
up not evicting any data send brings into the page cache, just like
before this change - but that however is not the common case.
Example scenario, on a box with 32G of RAM:
$ btrfs subvolume create /mnt/sv1
$ xfs_io -f -c "pwrite 0 4G" /mnt/sv1/file1
$ btrfs subvolume snapshot -r /mnt/sv1 /mnt/snap1
$ free -m
total used free shared buff/cache available
Mem: 31937 186 26866 0 4883 31297
Swap: 8188 0 8188
# After this we get less 4G of free memory.
$ btrfs send /mnt/snap1 >/dev/null
$ free -m
total used free shared buff/cache available
Mem: 31937 186 22814 0 8935 31297
Swap: 8188 0 8188
The same, obviously, applies to an incremental send.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Every time we send a write command, we open the inode, read some data to
a buffer and then close the inode. The amount of data we read for each
write command is at most 48K, returned by max_send_read_size(), and that
corresponds to: BTRFS_SEND_BUF_SIZE - 16K = 48K. In practice this does
not add any significant overhead, because the time elapsed between every
close (iput()) and open (btrfs_iget()) is very short, so the inode is kept
in the VFS's cache after the iput() and it's still there by the time we
do the next btrfs_iget().
As between processing extents of the current inode we don't do anything
else, it makes sense to keep the inode open after we process its first
extent that needs to be sent and keep it open until we start processing
the next inode. This serves to facilitate the next change, which aims
to avoid having send operations trash the page cache with data extents.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
… and adjust all usages of this object to use the XArray API for the sake
of consistency.
XArray API provides array semantics, so it is notionally easier to use and
understand, and it also takes care of locking for us.
None of this makes a real difference in this particular patch, but it does
in other places where similar replacements are or have been made and we
want to be consistent in our usage of data structures in btrfs.
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function can be simplified by refactoring to use the new iterator
macro. No functional changes.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function can be simplified by refactoring to use the new iterator
macro. No functional changes.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function can be simplified by refactoring to use the new iterator
macro. No functional changes.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function can be simplified by refactoring to use the new iterator
macro. No functional changes.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function can be simplified by refactoring to use the new iterator
macro. No functional changes.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function can be simplified by refactoring to use the new iterator
macro. No functional changes.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function can be simplified by refactoring to use the new iterator
macro. No functional changes.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: Gabriel Niebler <gniebler@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is a "weak" conversion which converts straight back to using pages.
A full conversion should be performed at some point, hopefully by
someone familiar with the filesystem.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Removes a couple of calls to compound_head and saves a few bytes.
Also convert verity's read_file_data_page() to be folio-based.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Return value from fs_path_add_path() directly instead of taking this in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_ioctl extracts inode from file so we can pass that into the
callbacks.
Signed-off-by: Sahil Kang <sahil.kang@asilaycomputing.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently if we get IO error while doing send then we abort without
logging information about which file caused issue. So log it to help
with debugging.
CC: stable@vger.kernel.org # 4.9+
Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We don't allow send and balance/relocation to run in parallel in order
to prevent send failing or silently producing some bad stream. This is
because while send is using an extent (specially metadata) or about to
read a metadata extent and expecting it belongs to a specific parent
node, relocation can run, the transaction used for the relocation is
committed and the extent gets reallocated while send is still using the
extent, so it ends up with a different content than expected. This can
result in just failing to read a metadata extent due to failure of the
validation checks (parent transid, level, etc), failure to find a
backreference for a data extent, and other unexpected failures. Besides
reallocation, there's also a similar problem of an extent getting
discarded when it's unpinned after the transaction used for block group
relocation is committed.
The restriction between balance and send was added in commit 9e967495e0
("Btrfs: prevent send failures and crashes due to concurrent relocation"),
kernel 5.3, while the more general restriction between send and relocation
was added in commit 1cea5cf0e6 ("btrfs: ensure relocation never runs
while we have send operations running"), kernel 5.14.
Both send and relocation can be very long running operations. Relocation
because it has to do a lot of IO and expensive backreference lookups in
case there are many snapshots, and send due to read IO when operating on
very large trees. This makes it inconvenient for users and tools to deal
with scheduling both operations.
For zoned filesystem we also have automatic block group relocation, so
send can fail with -EAGAIN when users least expect it or send can end up
delaying the block group relocation for too long. In the future we might
also get the automatic block group relocation for non zoned filesystems.
This change makes it possible for send and relocation to run in parallel.
This is achieved the following way:
1) For all tree searches, send acquires a read lock on the commit root
semaphore;
2) After each tree search, and before releasing the commit root semaphore,
the leaf is cloned and placed in the search path (struct btrfs_path);
3) After releasing the commit root semaphore, the changed_cb() callback
is invoked, which operates on the leaf and writes commands to the pipe
(or file in case send/receive is not used with a pipe). It's important
here to not hold a lock on the commit root semaphore, because if we did
we could deadlock when sending and receiving to the same filesystem
using a pipe - the send task blocks on the pipe because it's full, the
receive task, which is the only consumer of the pipe, triggers a
transaction commit when attempting to create a subvolume or reserve
space for a write operation for example, but the transaction commit
blocks trying to write lock the commit root semaphore, resulting in a
deadlock;
4) Before moving to the next key, or advancing to the next change in case
of an incremental send, check if a transaction used for relocation was
committed (or is about to finish its commit). If so, release the search
path(s) and restart the search, to where we were before, so that we
don't operate on stale extent buffers. The search restarts are always
possible because both the send and parent roots are RO, and no one can
add, remove of update keys (change their offset) in RO trees - the
only exception is deduplication, but that is still not allowed to run
in parallel with send;
5) Periodically check if there is contention on the commit root semaphore,
which means there is a transaction commit trying to write lock it, and
release the semaphore and reschedule if there is contention, so as to
avoid causing any significant delays to transaction commits.
This leaves some room for optimizations for send to have less path
releases and re searching the trees when there's relocation running, but
for now it's kept simple as it performs quite well (on very large trees
with resulting send streams in the order of a few hundred gigabytes).
Test case btrfs/187, from fstests, stresses relocation, send and
deduplication attempting to run in parallel, but without verifying if send
succeeds and if it produces correct streams. A new test case will be added
that exercises relocation happening in parallel with send and then checks
that send succeeds and the resulting streams are correct.
A final note is that for now this still leaves the mutual exclusion
between send operations and deduplication on files belonging to a root
used by send operations. A solution for that will be slightly more complex
but it will eventually be built on top of this change.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Again, I don't think this was ever used since iterate_dir_item() is only
used for xattrs. No functional change.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
As far as I can tell, this was never used. No functional change.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that all call sites are using the slot number to modify item values,
rename the SETGET helpers to raw_item_*(), and then rework the _nr()
helpers to be the btrfs_item_*() btrfs_set_item_*() helpers, and then
rename all of the callers to the new helpers.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have this pattern in a lot of places
item = btrfs_item_nr(slot);
btrfs_item_size(leaf, item);
when we could simply use
btrfs_item_size(leaf, slot);
Fix all callers of btrfs_item_size() and btrfs_item_offset() to use the
_nr variation of the helpers.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This is preparatory work for send protocol update to version 2 and
higher.
We have many pending protocol update requests but still don't have the
basic protocol rev in place, the first thing that must happen is to do
the actual versioning support.
The protocol version is u32 and is a new member in the send ioctl
struct. Validity of the version field is backed by a new flag bit. Old
kernels would fail when a higher version is requested. Version protocol
0 will pick the highest supported version, BTRFS_SEND_STREAM_VERSION,
that's also exported in sysfs.
The version is still unchanged and will be increased once we have new
incompatible commands or stream updates.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The out label is being overused, we can simply return if the condition
permits.
No functional changes.
Reviewed-by: Su Yue <l@damenly.su>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of using kmalloc() to allocate backref_ctx, allocate backref_ctx
on stack. The size is reasonably small.
sizeof(backref_ctx) = 48
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Comparators just read the data and thus get const parameters. This
should be also preserved by the local variables, update all comparators
passed to sort or bsearch.
Cleanups:
- unnecessary casts are dropped
- btrfs_cmp_device_free_bytes is cleaned up to follow the common pattern
and 'inline' is dropped as the function address is taken
Signed-off-by: David Sterba <dsterba@suse.com>
When doing a send we don't expect the task to ever start a transaction
after the initial check that verifies if commit roots match the regular
roots. This is because after that we set current->journal_info with a
stub (special value) that signals we are in send context, so that we take
a read lock on an extent buffer when reading it from disk and verifying
it is valid (its generation matches the generation stored in the parent).
This stub was introduced in 2014 by commit a26e8c9f75 ("Btrfs: don't
clear uptodate if the eb is under IO") in order to fix a concurrency issue
between send and balance.
However there is one particular exception where we end up needing to start
a transaction and when this happens it results in a crash with a stack
trace like the following:
[60015.902283] kernel: WARNING: CPU: 3 PID: 58159 at arch/x86/include/asm/kfence.h:44 kfence_protect_page+0x21/0x80
[60015.902292] kernel: Modules linked in: uinput rfcomm snd_seq_dummy (...)
[60015.902384] kernel: CPU: 3 PID: 58159 Comm: btrfs Not tainted 5.12.9-300.fc34.x86_64 #1
[60015.902387] kernel: Hardware name: Gigabyte Technology Co., Ltd. To be filled by O.E.M./F2A88XN-WIFI, BIOS F6 12/24/2015
[60015.902389] kernel: RIP: 0010:kfence_protect_page+0x21/0x80
[60015.902393] kernel: Code: ff 0f 1f 84 00 00 00 00 00 55 48 89 fd (...)
[60015.902396] kernel: RSP: 0018:ffff9fb583453220 EFLAGS: 00010246
[60015.902399] kernel: RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff9fb583453224
[60015.902401] kernel: RDX: ffff9fb583453224 RSI: 0000000000000000 RDI: 0000000000000000
[60015.902402] kernel: RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[60015.902404] kernel: R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000002
[60015.902406] kernel: R13: ffff9fb583453348 R14: 0000000000000000 R15: 0000000000000001
[60015.902408] kernel: FS: 00007f158e62d8c0(0000) GS:ffff93bd37580000(0000) knlGS:0000000000000000
[60015.902410] kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[60015.902412] kernel: CR2: 0000000000000039 CR3: 00000001256d2000 CR4: 00000000000506e0
[60015.902414] kernel: Call Trace:
[60015.902419] kernel: kfence_unprotect+0x13/0x30
[60015.902423] kernel: page_fault_oops+0x89/0x270
[60015.902427] kernel: ? search_module_extables+0xf/0x40
[60015.902431] kernel: ? search_bpf_extables+0x57/0x70
[60015.902435] kernel: kernelmode_fixup_or_oops+0xd6/0xf0
[60015.902437] kernel: __bad_area_nosemaphore+0x142/0x180
[60015.902440] kernel: exc_page_fault+0x67/0x150
[60015.902445] kernel: asm_exc_page_fault+0x1e/0x30
[60015.902450] kernel: RIP: 0010:start_transaction+0x71/0x580
[60015.902454] kernel: Code: d3 0f 84 92 00 00 00 80 e7 06 0f 85 63 (...)
[60015.902456] kernel: RSP: 0018:ffff9fb5834533f8 EFLAGS: 00010246
[60015.902458] kernel: RAX: 0000000000000001 RBX: 0000000000000001 RCX: 0000000000000000
[60015.902460] kernel: RDX: 0000000000000801 RSI: 0000000000000000 RDI: 0000000000000039
[60015.902462] kernel: RBP: ffff93bc0a7eb800 R08: 0000000000000001 R09: 0000000000000000
[60015.902463] kernel: R10: 0000000000098a00 R11: 0000000000000001 R12: 0000000000000001
[60015.902464] kernel: R13: 0000000000000000 R14: ffff93bc0c92b000 R15: ffff93bc0c92b000
[60015.902468] kernel: btrfs_commit_inode_delayed_inode+0x5d/0x120
[60015.902473] kernel: btrfs_evict_inode+0x2c5/0x3f0
[60015.902476] kernel: evict+0xd1/0x180
[60015.902480] kernel: inode_lru_isolate+0xe7/0x180
[60015.902483] kernel: __list_lru_walk_one+0x77/0x150
[60015.902487] kernel: ? iput+0x1a0/0x1a0
[60015.902489] kernel: ? iput+0x1a0/0x1a0
[60015.902491] kernel: list_lru_walk_one+0x47/0x70
[60015.902495] kernel: prune_icache_sb+0x39/0x50
[60015.902497] kernel: super_cache_scan+0x161/0x1f0
[60015.902501] kernel: do_shrink_slab+0x142/0x240
[60015.902505] kernel: shrink_slab+0x164/0x280
[60015.902509] kernel: shrink_node+0x2c8/0x6e0
[60015.902512] kernel: do_try_to_free_pages+0xcb/0x4b0
[60015.902514] kernel: try_to_free_pages+0xda/0x190
[60015.902516] kernel: __alloc_pages_slowpath.constprop.0+0x373/0xcc0
[60015.902521] kernel: ? __memcg_kmem_charge_page+0xc2/0x1e0
[60015.902525] kernel: __alloc_pages_nodemask+0x30a/0x340
[60015.902528] kernel: pipe_write+0x30b/0x5c0
[60015.902531] kernel: ? set_next_entity+0xad/0x1e0
[60015.902534] kernel: ? switch_mm_irqs_off+0x58/0x440
[60015.902538] kernel: __kernel_write+0x13a/0x2b0
[60015.902541] kernel: kernel_write+0x73/0x150
[60015.902543] kernel: send_cmd+0x7b/0xd0
[60015.902545] kernel: send_extent_data+0x5a3/0x6b0
[60015.902549] kernel: process_extent+0x19b/0xed0
[60015.902551] kernel: btrfs_ioctl_send+0x1434/0x17e0
[60015.902554] kernel: ? _btrfs_ioctl_send+0xe1/0x100
[60015.902557] kernel: _btrfs_ioctl_send+0xbf/0x100
[60015.902559] kernel: ? enqueue_entity+0x18c/0x7b0
[60015.902562] kernel: btrfs_ioctl+0x185f/0x2f80
[60015.902564] kernel: ? psi_task_change+0x84/0xc0
[60015.902569] kernel: ? _flat_send_IPI_mask+0x21/0x40
[60015.902572] kernel: ? check_preempt_curr+0x2f/0x70
[60015.902576] kernel: ? selinux_file_ioctl+0x137/0x1e0
[60015.902579] kernel: ? expand_files+0x1cb/0x1d0
[60015.902582] kernel: ? __x64_sys_ioctl+0x82/0xb0
[60015.902585] kernel: __x64_sys_ioctl+0x82/0xb0
[60015.902588] kernel: do_syscall_64+0x33/0x40
[60015.902591] kernel: entry_SYSCALL_64_after_hwframe+0x44/0xae
[60015.902595] kernel: RIP: 0033:0x7f158e38f0ab
[60015.902599] kernel: Code: ff ff ff 85 c0 79 9b (...)
[60015.902602] kernel: RSP: 002b:00007ffcb2519bf8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[60015.902605] kernel: RAX: ffffffffffffffda RBX: 00007ffcb251ae00 RCX: 00007f158e38f0ab
[60015.902607] kernel: RDX: 00007ffcb2519cf0 RSI: 0000000040489426 RDI: 0000000000000004
[60015.902608] kernel: RBP: 0000000000000004 R08: 00007f158e297640 R09: 00007f158e297640
[60015.902610] kernel: R10: 0000000000000008 R11: 0000000000000246 R12: 0000000000000000
[60015.902612] kernel: R13: 0000000000000002 R14: 00007ffcb251aee0 R15: 0000558c1a83e2a0
[60015.902615] kernel: ---[ end trace 7bbc33e23bb887ae ]---
This happens because when writing to the pipe, by calling kernel_write(),
we end up doing page allocations using GFP_HIGHUSER | __GFP_ACCOUNT as the
gfp flags, which allow reclaim to happen if there is memory pressure. This
allocation happens at fs/pipe.c:pipe_write().
If the reclaim is triggered, inode eviction can be triggered and that in
turn can result in starting a transaction if the inode has a link count
of 0. The transaction start happens early on during eviction, when we call
btrfs_commit_inode_delayed_inode() at btrfs_evict_inode(). This happens if
there is currently an open file descriptor for an inode with a link count
of 0 and the reclaim task gets a reference on the inode before that
descriptor is closed, in which case the reclaim task ends up doing the
final iput that triggers the inode eviction.
When we have assertions enabled (CONFIG_BTRFS_ASSERT=y), this triggers
the following assertion at transaction.c:start_transaction():
/* Send isn't supposed to start transactions. */
ASSERT(current->journal_info != BTRFS_SEND_TRANS_STUB);
And when assertions are not enabled, it triggers a crash since after that
assertion we cast current->journal_info into a transaction handle pointer
and then dereference it:
if (current->journal_info) {
WARN_ON(type & TRANS_EXTWRITERS);
h = current->journal_info;
refcount_inc(&h->use_count);
(...)
Which obviously results in a crash due to an invalid memory access.
The same type of issue can happen during other memory allocations we
do directly in the send code with kmalloc (and friends) as they use
GFP_KERNEL and therefore may trigger reclaim too, which started to
happen since 2016 after commit e780b0d1c1 ("btrfs: send: use
GFP_KERNEL everywhere").
The issue could be solved by setting up a NOFS context for the entire
send operation so that reclaim could not be triggered when allocating
memory or pages through kernel_write(). However that is not very friendly
and we can in fact get rid of the send stub because:
1) The stub was introduced way back in 2014 by commit a26e8c9f75
("Btrfs: don't clear uptodate if the eb is under IO") to solve an
issue exclusive to when send and balance are running in parallel,
however there were other problems between balance and send and we do
not allow anymore to have balance and send run concurrently since
commit 9e967495e0 ("Btrfs: prevent send failures and crashes due
to concurrent relocation"). More generically the issues are between
send and relocation, and that last commit eliminated only the
possibility of having send and balance run concurrently, but shrinking
a device also can trigger relocation, and on zoned filesystems we have
relocation of partially used block groups triggered automatically as
well. The previous patch that has a subject of:
"btrfs: ensure relocation never runs while we have send operations running"
Addresses all the remaining cases that can trigger relocation.
2) We can actually allow starting and even committing transactions while
in a send context if needed because send is not holding any locks that
would block the start or the commit of a transaction.
So get rid of all the logic added by commit a26e8c9f75 ("Btrfs: don't
clear uptodate if the eb is under IO"). We can now always call
clear_extent_buffer_uptodate() at verify_parent_transid() since send is
the only case that uses commit roots without having a transaction open or
without holding the commit_root_sem.
Reported-by: Chris Murphy <lists@colorremedies.com>
Link: https://lore.kernel.org/linux-btrfs/CAJCQCtRQ57=qXo3kygwpwEBOU_CA_eKvdmjP52sU=eFvuVOEGw@mail.gmail.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Relocation and send do not play well together because while send is
running a block group can be relocated, a transaction committed and
the respective disk extents get re-allocated and written to or discarded
while send is about to do something with the extents.
This was explained in commit 9e967495e0 ("Btrfs: prevent send failures
and crashes due to concurrent relocation"), which prevented balance and
send from running in parallel but it did not address one remaining case
where chunk relocation can happen: shrinking a device (and device deletion
which shrinks a device's size to 0 before deleting the device).
We also have now one more case where relocation is triggered: on zoned
filesystems partially used block groups get relocated by a background
thread, introduced in commit 18bb8bbf13 ("btrfs: zoned: automatically
reclaim zones").
So make sure that instead of preventing balance from running when there
are ongoing send operations, we prevent relocation from happening.
This uses the infrastructure recently added by a patch that has the
subject: "btrfs: add cancellable chunk relocation support".
Also it adds a spinlock used exclusively for the exclusivity between
send and relocation, as before fs_info->balance_mutex was used, which
would make an attempt to run send to block waiting for balance to
finish, which can take a lot of time on large filesystems.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use list_move_tail() instead of list_del() + list_add_tail() as it's
doing the same thing and allows further cleanups. Open code
name_cache_used() as there is only one user.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
During an incremental send operation, when processing the new references
for the current inode, we might send an unlink operation for another inode
that has a conflicting path and has more than one hard link. However this
path was computed and cached before we processed previous new references
for the current inode. We may have orphanized a directory of that path
while processing a previous new reference, in which case the path will
be invalid and cause the receiver process to fail.
The following reproducer triggers the problem and explains how/why it
happens in its comments:
$ cat test-send-unlink.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# Create our test files and directory. Inode 259 (file3) has two hard
# links.
touch $MNT/file1
touch $MNT/file2
touch $MNT/file3
mkdir $MNT/A
ln $MNT/file3 $MNT/A/hard_link
# Filesystem looks like:
#
# . (ino 256)
# |----- file1 (ino 257)
# |----- file2 (ino 258)
# |----- file3 (ino 259)
# |----- A/ (ino 260)
# |---- hard_link (ino 259)
#
# Now create the base snapshot, which is going to be the parent snapshot
# for a later incremental send.
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send -f /tmp/snap1.send $MNT/snap1
# Move inode 257 into directory inode 260. This results in computing the
# path for inode 260 as "/A" and caching it.
mv $MNT/file1 $MNT/A/file1
# Move inode 258 (file2) into directory inode 260, with a name of
# "hard_link", moving first inode 259 away since it currently has that
# location and name.
mv $MNT/A/hard_link $MNT/tmp
mv $MNT/file2 $MNT/A/hard_link
# Now rename inode 260 to something else (B for example) and then create
# a hard link for inode 258 that has the old name and location of inode
# 260 ("/A").
mv $MNT/A $MNT/B
ln $MNT/B/hard_link $MNT/A
# Filesystem now looks like:
#
# . (ino 256)
# |----- tmp (ino 259)
# |----- file3 (ino 259)
# |----- B/ (ino 260)
# | |---- file1 (ino 257)
# | |---- hard_link (ino 258)
# |
# |----- A (ino 258)
# Create another snapshot of our subvolume and use it for an incremental
# send.
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2
# Now unmount the filesystem, create a new one, mount it and try to
# apply both send streams to recreate both snapshots.
umount $DEV
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# First add the first snapshot to the new filesystem by applying the
# first send stream.
btrfs receive -f /tmp/snap1.send $MNT
# The incremental receive operation below used to fail with the
# following error:
#
# ERROR: unlink A/hard_link failed: No such file or directory
#
# This is because when send is processing inode 257, it generates the
# path for inode 260 as "/A", since that inode is its parent in the send
# snapshot, and caches that path.
#
# Later when processing inode 258, it first processes its new reference
# that has the path of "/A", which results in orphanizing inode 260
# because there is a a path collision. This results in issuing a rename
# operation from "/A" to "/o260-6-0".
#
# Finally when processing the new reference "B/hard_link" for inode 258,
# it notices that it collides with inode 259 (not yet processed, because
# it has a higher inode number), since that inode has the name
# "hard_link" under the directory inode 260. It also checks that inode
# 259 has two hardlinks, so it decides to issue a unlink operation for
# the name "hard_link" for inode 259. However the path passed to the
# unlink operation is "/A/hard_link", which is incorrect since currently
# "/A" does not exists, due to the orphanization of inode 260 mentioned
# before. The path is incorrect because it was computed and cached
# before the orphanization. This results in the receiver to fail with
# the above error.
btrfs receive -f /tmp/snap2.send $MNT
umount $MNT
When running the test, it fails like this:
$ ./test-send-unlink.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: unlink A/hard_link failed: No such file or directory
Fix this by recomputing a path before issuing an unlink operation when
processing the new references for the current inode if we previously
have orphanized a directory.
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are a few exceptional cases where cloning an inline extent needs to
copy the inline extent data into a page of the destination inode.
When this happens, we end up starting a transaction while having a dirty
page for the destination inode and while having the range locked in the
destination's inode iotree too. Because when reserving metadata space
for a transaction we may need to flush existing delalloc in case there is
not enough free space, we have a mechanism in place to prevent a deadlock,
which was introduced in commit 3d45f221ce ("btrfs: fix deadlock when
cloning inline extent and low on free metadata space").
However when using qgroups, a transaction also reserves metadata qgroup
space, which can also result in flushing delalloc in case there is not
enough available space at the moment. When this happens we deadlock, since
flushing delalloc requires locking the file range in the inode's iotree
and the range was already locked at the very beginning of the clone
operation, before attempting to start the transaction.
When this issue happens, stack traces like the following are reported:
[72747.556262] task:kworker/u81:9 state:D stack: 0 pid: 225 ppid: 2 flags:0x00004000
[72747.556268] Workqueue: writeback wb_workfn (flush-btrfs-1142)
[72747.556271] Call Trace:
[72747.556273] __schedule+0x296/0x760
[72747.556277] schedule+0x3c/0xa0
[72747.556279] io_schedule+0x12/0x40
[72747.556284] __lock_page+0x13c/0x280
[72747.556287] ? generic_file_readonly_mmap+0x70/0x70
[72747.556325] extent_write_cache_pages+0x22a/0x440 [btrfs]
[72747.556331] ? __set_page_dirty_nobuffers+0xe7/0x160
[72747.556358] ? set_extent_buffer_dirty+0x5e/0x80 [btrfs]
[72747.556362] ? update_group_capacity+0x25/0x210
[72747.556366] ? cpumask_next_and+0x1a/0x20
[72747.556391] extent_writepages+0x44/0xa0 [btrfs]
[72747.556394] do_writepages+0x41/0xd0
[72747.556398] __writeback_single_inode+0x39/0x2a0
[72747.556403] writeback_sb_inodes+0x1ea/0x440
[72747.556407] __writeback_inodes_wb+0x5f/0xc0
[72747.556410] wb_writeback+0x235/0x2b0
[72747.556414] ? get_nr_inodes+0x35/0x50
[72747.556417] wb_workfn+0x354/0x490
[72747.556420] ? newidle_balance+0x2c5/0x3e0
[72747.556424] process_one_work+0x1aa/0x340
[72747.556426] worker_thread+0x30/0x390
[72747.556429] ? create_worker+0x1a0/0x1a0
[72747.556432] kthread+0x116/0x130
[72747.556435] ? kthread_park+0x80/0x80
[72747.556438] ret_from_fork+0x1f/0x30
[72747.566958] Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs]
[72747.566961] Call Trace:
[72747.566964] __schedule+0x296/0x760
[72747.566968] ? finish_wait+0x80/0x80
[72747.566970] schedule+0x3c/0xa0
[72747.566995] wait_extent_bit.constprop.68+0x13b/0x1c0 [btrfs]
[72747.566999] ? finish_wait+0x80/0x80
[72747.567024] lock_extent_bits+0x37/0x90 [btrfs]
[72747.567047] btrfs_invalidatepage+0x299/0x2c0 [btrfs]
[72747.567051] ? find_get_pages_range_tag+0x2cd/0x380
[72747.567076] __extent_writepage+0x203/0x320 [btrfs]
[72747.567102] extent_write_cache_pages+0x2bb/0x440 [btrfs]
[72747.567106] ? update_load_avg+0x7e/0x5f0
[72747.567109] ? enqueue_entity+0xf4/0x6f0
[72747.567134] extent_writepages+0x44/0xa0 [btrfs]
[72747.567137] ? enqueue_task_fair+0x93/0x6f0
[72747.567140] do_writepages+0x41/0xd0
[72747.567144] __filemap_fdatawrite_range+0xc7/0x100
[72747.567167] btrfs_run_delalloc_work+0x17/0x40 [btrfs]
[72747.567195] btrfs_work_helper+0xc2/0x300 [btrfs]
[72747.567200] process_one_work+0x1aa/0x340
[72747.567202] worker_thread+0x30/0x390
[72747.567205] ? create_worker+0x1a0/0x1a0
[72747.567208] kthread+0x116/0x130
[72747.567211] ? kthread_park+0x80/0x80
[72747.567214] ret_from_fork+0x1f/0x30
[72747.569686] task:fsstress state:D stack: 0 pid:841421 ppid:841417 flags:0x00000000
[72747.569689] Call Trace:
[72747.569691] __schedule+0x296/0x760
[72747.569694] schedule+0x3c/0xa0
[72747.569721] try_flush_qgroup+0x95/0x140 [btrfs]
[72747.569725] ? finish_wait+0x80/0x80
[72747.569753] btrfs_qgroup_reserve_data+0x34/0x50 [btrfs]
[72747.569781] btrfs_check_data_free_space+0x5f/0xa0 [btrfs]
[72747.569804] btrfs_buffered_write+0x1f7/0x7f0 [btrfs]
[72747.569810] ? path_lookupat.isra.48+0x97/0x140
[72747.569833] btrfs_file_write_iter+0x81/0x410 [btrfs]
[72747.569836] ? __kmalloc+0x16a/0x2c0
[72747.569839] do_iter_readv_writev+0x160/0x1c0
[72747.569843] do_iter_write+0x80/0x1b0
[72747.569847] vfs_writev+0x84/0x140
[72747.569869] ? btrfs_file_llseek+0x38/0x270 [btrfs]
[72747.569873] do_writev+0x65/0x100
[72747.569876] do_syscall_64+0x33/0x40
[72747.569879] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[72747.569899] task:fsstress state:D stack: 0 pid:841424 ppid:841417 flags:0x00004000
[72747.569903] Call Trace:
[72747.569906] __schedule+0x296/0x760
[72747.569909] schedule+0x3c/0xa0
[72747.569936] try_flush_qgroup+0x95/0x140 [btrfs]
[72747.569940] ? finish_wait+0x80/0x80
[72747.569967] __btrfs_qgroup_reserve_meta+0x36/0x50 [btrfs]
[72747.569989] start_transaction+0x279/0x580 [btrfs]
[72747.570014] clone_copy_inline_extent+0x332/0x490 [btrfs]
[72747.570041] btrfs_clone+0x5b7/0x7a0 [btrfs]
[72747.570068] ? lock_extent_bits+0x64/0x90 [btrfs]
[72747.570095] btrfs_clone_files+0xfc/0x150 [btrfs]
[72747.570122] btrfs_remap_file_range+0x3d8/0x4a0 [btrfs]
[72747.570126] do_clone_file_range+0xed/0x200
[72747.570131] vfs_clone_file_range+0x37/0x110
[72747.570134] ioctl_file_clone+0x7d/0xb0
[72747.570137] do_vfs_ioctl+0x138/0x630
[72747.570140] __x64_sys_ioctl+0x62/0xc0
[72747.570143] do_syscall_64+0x33/0x40
[72747.570146] entry_SYSCALL_64_after_hwframe+0x44/0xa9
So fix this by skipping the flush of delalloc for an inode that is
flagged with BTRFS_INODE_NO_DELALLOC_FLUSH, meaning it is currently under
such a special case of cloning an inline extent, when flushing delalloc
during qgroup metadata reservation.
The special cases for cloning inline extents were added in kernel 5.7 by
by commit 05a5a7621c ("Btrfs: implement full reflink support for
inline extents"), while having qgroup metadata space reservation flushing
delalloc when low on space was added in kernel 5.9 by commit
c53e965360 ("btrfs: qgroup: try to flush qgroup space when we get
-EDQUOT"). So use a "Fixes:" tag for the later commit to ease stable
kernel backports.
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20210421083137.31E3.409509F4@e16-tech.com/
Fixes: c53e965360 ("btrfs: qgroup: try to flush qgroup space when we get -EDQUOT")
CC: stable@vger.kernel.org # 5.9+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently a full send operation uses the standard btree readahead when
iterating over the subvolume/snapshot btree, which despite bringing good
performance benefits, it could be improved in a few aspects for use cases
such as full send operations, which are guaranteed to visit every node
and leaf of a btree, in ascending and sequential order. The limitations
of that standard btree readahead implementation are the following:
1) It only triggers readahead for leaves that are physically close
to the leaf being read, within a 64K range;
2) It only triggers readahead for the next or previous leaves if the
leaf being read is not currently in memory;
3) It never triggers readahead for nodes.
So add a new readahead mode that addresses all these points and use it
for full send operations.
The following test script was used to measure the improvement on a box
using an average, consumer grade, spinning disk and with 16GiB of RAM:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
MKFS_OPTIONS="--nodesize 16384" # default, just to be explicit
MOUNT_OPTIONS="-o max_inline=2048" # default, just to be explicit
mkfs.btrfs -f $MKFS_OPTIONS $DEV > /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
# Create files with inline data to make it easier and faster to create
# large btrees.
add_files()
{
local total=$1
local start_offset=$2
local number_jobs=$3
local total_per_job=$(($total / $number_jobs))
echo "Creating $total new files using $number_jobs jobs"
for ((n = 0; n < $number_jobs; n++)); do
(
local start_num=$(($start_offset + $n * $total_per_job))
for ((i = 1; i <= $total_per_job; i++)); do
local file_num=$((start_num + $i))
local file_path="$MNT/file_${file_num}"
xfs_io -f -c "pwrite -S 0xab 0 2000" $file_path > /dev/null
if [ $? -ne 0 ]; then
echo "Failed creating file $file_path"
break
fi
done
) &
worker_pids[$n]=$!
done
wait ${worker_pids[@]}
sync
echo
echo "btree node/leaf count: $(btrfs inspect-internal dump-tree -t 5 $DEV | egrep '^(node|leaf) ' | wc -l)"
}
initial_file_count=500000
add_files $initial_file_count 0 4
echo
echo "Creating first snapshot..."
btrfs subvolume snapshot -r $MNT $MNT/snap1
echo
echo "Adding more files..."
add_files $((initial_file_count / 4)) $initial_file_count 4
echo
echo "Updating 1/50th of the initial files..."
for ((i = 1; i < $initial_file_count; i += 50)); do
xfs_io -c "pwrite -S 0xcd 0 20" $MNT/file_$i > /dev/null
done
echo
echo "Creating second snapshot..."
btrfs subvolume snapshot -r $MNT $MNT/snap2
umount $MNT
echo 3 > /proc/sys/vm/drop_caches
blockdev --flushbufs $DEV &> /dev/null
hdparm -F $DEV &> /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo
echo "Testing full send..."
start=$(date +%s)
btrfs send $MNT/snap1 > /dev/null
end=$(date +%s)
echo
echo "Full send took $((end - start)) seconds"
umount $MNT
The durations of the full send operation in seconds were the following:
Before this change: 217 seconds
After this change: 205 seconds (-5.7%)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently we do not do btree read ahead when doing an incremental send,
however we know that we will read and process any node or leaf in the
send root that has a generation greater than the generation of the parent
root. So triggering read ahead for such nodes and leafs is beneficial
for an incremental send.
This change does that, triggers read ahead of any node or leaf in the
send root that has a generation greater then the generation of the
parent root. As for the parent root, no readahead is triggered because
knowing in advance which nodes/leaves are going to be read is not so
linear and there's often a large time window between visiting nodes or
leaves of the parent root. So I opted to leave out the parent root,
and triggering read ahead for its nodes/leaves seemed to have not made
significant difference.
The following test script was used to measure the improvement on a box
using an average, consumer grade, spinning disk and with 16GiB of ram:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
MKFS_OPTIONS="--nodesize 16384" # default, just to be explicit
MOUNT_OPTIONS="-o max_inline=2048" # default, just to be explicit
mkfs.btrfs -f $MKFS_OPTIONS $DEV > /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
# Create files with inline data to make it easier and faster to create
# large btrees.
add_files()
{
local total=$1
local start_offset=$2
local number_jobs=$3
local total_per_job=$(($total / $number_jobs))
echo "Creating $total new files using $number_jobs jobs"
for ((n = 0; n < $number_jobs; n++)); do
(
local start_num=$(($start_offset + $n * $total_per_job))
for ((i = 1; i <= $total_per_job; i++)); do
local file_num=$((start_num + $i))
local file_path="$MNT/file_${file_num}"
xfs_io -f -c "pwrite -S 0xab 0 2000" $file_path > /dev/null
if [ $? -ne 0 ]; then
echo "Failed creating file $file_path"
break
fi
done
) &
worker_pids[$n]=$!
done
wait ${worker_pids[@]}
sync
echo
echo "btree node/leaf count: $(btrfs inspect-internal dump-tree -t 5 $DEV | egrep '^(node|leaf) ' | wc -l)"
}
initial_file_count=500000
add_files $initial_file_count 0 4
echo
echo "Creating first snapshot..."
btrfs subvolume snapshot -r $MNT $MNT/snap1
echo
echo "Adding more files..."
add_files $((initial_file_count / 4)) $initial_file_count 4
echo
echo "Updating 1/50th of the initial files..."
for ((i = 1; i < $initial_file_count; i += 50)); do
xfs_io -c "pwrite -S 0xcd 0 20" $MNT/file_$i > /dev/null
done
echo
echo "Creating second snapshot..."
btrfs subvolume snapshot -r $MNT $MNT/snap2
umount $MNT
echo 3 > /proc/sys/vm/drop_caches
blockdev --flushbufs $DEV &> /dev/null
hdparm -F $DEV &> /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo
echo "Testing full send..."
start=$(date +%s)
btrfs send $MNT/snap1 > /dev/null
end=$(date +%s)
echo
echo "Full send took $((end - start)) seconds"
umount $MNT
echo 3 > /proc/sys/vm/drop_caches
blockdev --flushbufs $DEV &> /dev/null
hdparm -F $DEV &> /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo
echo "Testing incremental send..."
start=$(date +%s)
btrfs send -p $MNT/snap1 $MNT/snap2 > /dev/null
end=$(date +%s)
echo
echo "Incremental send took $((end - start)) seconds"
umount $MNT
Before this change, incremental send duration:
with $initial_file_count == 200000: 51 seconds
with $initial_file_count == 500000: 168 seconds
After this change, incremental send duration:
with $initial_file_count == 200000: 39 seconds (-26.7%)
with $initial_file_count == 500000: 125 seconds (-29.4%)
For $initial_file_count == 200000 there are 62600 nodes and leaves in the
btree of the first snapshot, and 77759 nodes and leaves in the btree of
the second snapshot. The root nodes were at level 2.
While for $initial_file_count == 500000 there are 152476 nodes and leaves
in the btree of the first snapshot, and 190511 nodes and leaves in the
btree of the second snapshot. The root nodes were at level 2 as well.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing a full send we know that we are going to be reading every node
and leaf of the send root, so we benefit from enabling read ahead for the
btree.
This change enables read ahead for full send operations only, incremental
sends will have read ahead enabled in a different way by a separate patch.
The following test script was used to measure the improvement on a box
using an average, consumer grade, spinning disk and with 16GiB of RAM:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
MKFS_OPTIONS="--nodesize 16384" # default, just to be explicit
MOUNT_OPTIONS="-o max_inline=2048" # default, just to be explicit
mkfs.btrfs -f $MKFS_OPTIONS $DEV > /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
# Create files with inline data to make it easier and faster to create
# large btrees.
add_files()
{
local total=$1
local start_offset=$2
local number_jobs=$3
local total_per_job=$(($total / $number_jobs))
echo "Creating $total new files using $number_jobs jobs"
for ((n = 0; n < $number_jobs; n++)); do
(
local start_num=$(($start_offset + $n * $total_per_job))
for ((i = 1; i <= $total_per_job; i++)); do
local file_num=$((start_num + $i))
local file_path="$MNT/file_${file_num}"
xfs_io -f -c "pwrite -S 0xab 0 2000" $file_path > /dev/null
if [ $? -ne 0 ]; then
echo "Failed creating file $file_path"
break
fi
done
) &
worker_pids[$n]=$!
done
wait ${worker_pids[@]}
sync
echo
echo "btree node/leaf count: $(btrfs inspect-internal dump-tree -t 5 $DEV | egrep '^(node|leaf) ' | wc -l)"
}
initial_file_count=500000
add_files $initial_file_count 0 4
echo
echo "Creating first snapshot..."
btrfs subvolume snapshot -r $MNT $MNT/snap1
echo
echo "Adding more files..."
add_files $((initial_file_count / 4)) $initial_file_count 4
echo
echo "Updating 1/50th of the initial files..."
for ((i = 1; i < $initial_file_count; i += 50)); do
xfs_io -c "pwrite -S 0xcd 0 20" $MNT/file_$i > /dev/null
done
echo
echo "Creating second snapshot..."
btrfs subvolume snapshot -r $MNT $MNT/snap2
umount $MNT
echo 3 > /proc/sys/vm/drop_caches
blockdev --flushbufs $DEV &> /dev/null
hdparm -F $DEV &> /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo
echo "Testing full send..."
start=$(date +%s)
btrfs send $MNT/snap1 > /dev/null
end=$(date +%s)
echo
echo "Full send took $((end - start)) seconds"
umount $MNT
echo 3 > /proc/sys/vm/drop_caches
blockdev --flushbufs $DEV &> /dev/null
hdparm -F $DEV &> /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo
echo "Testing incremental send..."
start=$(date +%s)
btrfs send -p $MNT/snap1 $MNT/snap2 > /dev/null
end=$(date +%s)
echo
echo "Incremental send took $((end - start)) seconds"
umount $MNT
Before this change, full send duration:
with $initial_file_count == 200000: 165 seconds
with $initial_file_count == 500000: 407 seconds
After this change, full send duration:
with $initial_file_count == 200000: 149 seconds (-10.2%)
with $initial_file_count == 500000: 353 seconds (-14.2%)
For $initial_file_count == 200000 there are 62600 nodes and leaves in the
btree of the first snapshot, while for $initial_file_count == 500000 there
are 152476 nodes and leaves. The roots were at level 2.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull kmap conversion updates from David Sterba:
"This contains changes regarding kmap API use and eg conversion from
kmap_atomic to kmap_local_page.
The API belongs to memory management but to save cross-tree
dependency headaches we've agreed to take it through the btrfs tree
because there are some trivial conversions possible, while the rest
will need some time and getting the easy cases out of the way would be
convenient.
The changes can be grouped:
- function exports, new helpers
- new VM_BUG_ON for additional verification; it's been discussed if
it should be VM_BUG_ON or BUG_ON, the former was chosen due to
performance reasons
- code replaced by relevant helpers"
[ This is an updated version of a request that originally came in during
the merge window, but I asked for some updates:
https://lore.kernel.org/lkml/cover.1614090658.git.dsterba@suse.com/
which is why this got merge after the merge window closed. - Linus ]
* 'kmap-conversion-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: use copy_highpage() instead of 2 kmaps()
btrfs: use memcpy_[to|from]_page() and kmap_local_page()
mm/highmem: Add VM_BUG_ON() to mem*_page() calls
mm/highmem: Introduce memcpy_page(), memmove_page(), and memset_page()
mm/highmem: Convert memcpy_[to|from]_page() to kmap_local_page()
mm/highmem: Lift memcpy_[to|from]_page to core
There are many places where the pattern kmap/memcpy/kunmap occurs.
This pattern was lifted to the core common functions
memcpy_[to|from]_page().
Use these new functions to reduce the code, eliminate direct uses of
kmap, and leverage the new core functions use of kmap_local_page().
Also, there is 1 place where a kmap/memcpy is followed by an
optional memset. Here we leave the kmap open coded to avoid remapping
the page but use kmap_local_page() directly.
Development of this patch was aided by the coccinelle script:
// <smpl>
// SPDX-License-Identifier: GPL-2.0-only
// Find kmap/memcpy/kunmap pattern and replace with memcpy*page calls
//
// NOTE: Offsets and other expressions may be more complex than what the script
// will automatically generate. Therefore a catchall rule is provided to find
// the pattern which then must be evaluated by hand.
//
// Confidence: Low
// Copyright: (C) 2021 Intel Corporation
// URL: http://coccinelle.lip6.fr/
// Comments:
// Options:
//
// simple memcpy version
//
@ memcpy_rule1 @
expression page, T, F, B, Off;
identifier ptr;
type VP;
@@
(
-VP ptr = kmap(page);
|
-ptr = kmap(page);
|
-VP ptr = kmap_atomic(page);
|
-ptr = kmap_atomic(page);
)
<+...
(
-memcpy(ptr + Off, F, B);
+memcpy_to_page(page, Off, F, B);
|
-memcpy(ptr, F, B);
+memcpy_to_page(page, 0, F, B);
|
-memcpy(T, ptr + Off, B);
+memcpy_from_page(T, page, Off, B);
|
-memcpy(T, ptr, B);
+memcpy_from_page(T, page, 0, B);
)
...+>
(
-kunmap(page);
|
-kunmap_atomic(ptr);
)
// Remove any pointers left unused
@
depends on memcpy_rule1
@
identifier memcpy_rule1.ptr;
type VP, VP1;
@@
-VP ptr;
... when != ptr;
? VP1 ptr;
//
// Some callers kmap without a temp pointer
//
@ memcpy_rule2 @
expression page, T, Off, F, B;
@@
<+...
(
-memcpy(kmap(page) + Off, F, B);
+memcpy_to_page(page, Off, F, B);
|
-memcpy(kmap(page), F, B);
+memcpy_to_page(page, 0, F, B);
|
-memcpy(T, kmap(page) + Off, B);
+memcpy_from_page(T, page, Off, B);
|
-memcpy(T, kmap(page), B);
+memcpy_from_page(T, page, 0, B);
)
...+>
-kunmap(page);
// No need for the ptr variable removal
//
// Catch all
//
@ memcpy_rule3 @
expression page;
expression GenTo, GenFrom, GenSize;
identifier ptr;
type VP;
@@
(
-VP ptr = kmap(page);
|
-ptr = kmap(page);
|
-VP ptr = kmap_atomic(page);
|
-ptr = kmap_atomic(page);
)
<+...
(
//
// Some call sites have complex expressions within the memcpy
// match a catch all to be evaluated by hand.
//
-memcpy(GenTo, GenFrom, GenSize);
+memcpy_to_pageExtra(page, GenTo, GenFrom, GenSize);
+memcpy_from_pageExtra(GenTo, page, GenFrom, GenSize);
)
...+>
(
-kunmap(page);
|
-kunmap_atomic(ptr);
)
// Remove any pointers left unused
@
depends on memcpy_rule3
@
identifier memcpy_rule3.ptr;
type VP, VP1;
@@
-VP ptr;
... when != ptr;
? VP1 ptr;
// <smpl>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_compare_trees and changed_cb use a void *ctx parameter instead of
struct send_ctx *sctx but when used in changed_cb it is immediately
cast to `struct send_ctx *sctx = ctx;`.
changed_cb is only ever called from btrfs_compare_trees and full_send_tree:
- full_send_tree already passes a struct send_ctx *sctx
- btrfs_compare_trees is only called by send_subvol with a struct send_ctx *sctx
- void *ctx in btrfs_compare_trees is only used to be passed to changed_cb
So casting to/from void *ctx seems unnecessary and directly using
struct send_ctx *sctx instead provides better type-safety.
The original reason for using void *ctx in the first place seems to have
been dropped with 1b51d6fce4 ("btrfs: send: remove indirect callback
parameter for changed_cb").
Signed-off-by: Roman Anasal <roman.anasal@bdsu.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
After commit 040ee6120c ("Btrfs: send, improve clone range") we do not
use anymore the data_offset field of struct backref_ctx, as after that we
do all the necessary checks for the data offset of file extent items at
clone_range(). Since there are no more users of data_offset from that
structure, remove it.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When an incremental send finds an extent that is shared, it checks which
file extent items in the range refer to that extent, and for those it
emits clone operations, while for others it emits regular write operations
to avoid corruption at the destination (as described and fixed by commit
d906d49fc5 ("Btrfs: send, fix file corruption due to incorrect cloning
operations")).
However when the root we are cloning from is the send root, we are cloning
from the inode currently being processed and the source file range has
several extent items that partially point to the desired extent, with an
offset smaller than the offset in the file extent item for the range we
want to clone into, it can cause the algorithm to issue a clone operation
that starts at the current eof of the file being processed in the receiver
side, in which case the receiver will fail, with EINVAL, when attempting
to execute the clone operation.
Example reproducer:
$ cat test-send-clone.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# Create our test file with a single and large extent (1M) and with
# different content for different file ranges that will be reflinked
# later.
xfs_io -f \
-c "pwrite -S 0xab 0 128K" \
-c "pwrite -S 0xcd 128K 128K" \
-c "pwrite -S 0xef 256K 256K" \
-c "pwrite -S 0x1a 512K 512K" \
$MNT/foobar
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send -f /tmp/snap1.send $MNT/snap1
# Now do a series of changes to our file such that we end up with
# different parts of the extent reflinked into different file offsets
# and we overwrite a large part of the extent too, so no file extent
# items refer to that part that was overwritten. This used to confuse
# the algorithm used by the kernel to figure out which file ranges to
# clone, making it attempt to clone from a source range starting at
# the current eof of the file, resulting in the receiver to fail since
# it is an invalid clone operation.
#
xfs_io -c "reflink $MNT/foobar 64K 1M 960K" \
-c "reflink $MNT/foobar 0K 512K 256K" \
-c "reflink $MNT/foobar 512K 128K 256K" \
-c "pwrite -S 0x73 384K 640K" \
$MNT/foobar
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2
echo -e "\nFile digest in the original filesystem:"
md5sum $MNT/snap2/foobar
# Now unmount the filesystem, create a new one, mount it and try to
# apply both send streams to recreate both snapshots.
umount $DEV
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
btrfs receive -f /tmp/snap1.send $MNT
btrfs receive -f /tmp/snap2.send $MNT
# Must match what we got in the original filesystem of course.
echo -e "\nFile digest in the new filesystem:"
md5sum $MNT/snap2/foobar
umount $MNT
When running the reproducer, the incremental send operation fails due to
an invalid clone operation:
$ ./test-send-clone.sh
wrote 131072/131072 bytes at offset 0
128 KiB, 32 ops; 0.0015 sec (80.906 MiB/sec and 20711.9741 ops/sec)
wrote 131072/131072 bytes at offset 131072
128 KiB, 32 ops; 0.0013 sec (90.514 MiB/sec and 23171.6148 ops/sec)
wrote 262144/262144 bytes at offset 262144
256 KiB, 64 ops; 0.0025 sec (98.270 MiB/sec and 25157.2327 ops/sec)
wrote 524288/524288 bytes at offset 524288
512 KiB, 128 ops; 0.0052 sec (95.730 MiB/sec and 24506.9883 ops/sec)
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
linked 983040/983040 bytes at offset 1048576
960 KiB, 1 ops; 0.0006 sec (1.419 GiB/sec and 1550.3876 ops/sec)
linked 262144/262144 bytes at offset 524288
256 KiB, 1 ops; 0.0020 sec (120.192 MiB/sec and 480.7692 ops/sec)
linked 262144/262144 bytes at offset 131072
256 KiB, 1 ops; 0.0018 sec (133.833 MiB/sec and 535.3319 ops/sec)
wrote 655360/655360 bytes at offset 393216
640 KiB, 160 ops; 0.0093 sec (66.781 MiB/sec and 17095.8436 ops/sec)
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
File digest in the original filesystem:
9c13c61cb0b9f5abf45344375cb04dfa /mnt/sdi/snap2/foobar
At subvol snap1
At snapshot snap2
ERROR: failed to clone extents to foobar: Invalid argument
File digest in the new filesystem:
132f0396da8f48d2e667196bff882cfc /mnt/sdi/snap2/foobar
The clone operation is invalid because its source range starts at the
current eof of the file in the receiver, causing the receiver to get
an EINVAL error from the clone operation when attempting it.
For the example above, what happens is the following:
1) When processing the extent at file offset 1M, the algorithm checks that
the extent is shared and can be (fully or partially) found at file
offset 0.
At this point the file has a size (and eof) of 1M at the receiver;
2) It finds that our extent item at file offset 1M has a data offset of
64K and, since the file extent item at file offset 0 has a data offset
of 0, it issues a clone operation, from the same file and root, that
has a source range offset of 64K, destination offset of 1M and a length
of 64K, since the extent item at file offset 0 refers only to the first
128K of the shared extent.
After this clone operation, the file size (and eof) at the receiver is
increased from 1M to 1088K (1M + 64K);
3) Now there's still 896K (960K - 64K) of data left to clone or write, so
it checks for the next file extent item, which starts at file offset
128K. This file extent item has a data offset of 0 and a length of
256K, so a clone operation with a source range offset of 256K, a
destination offset of 1088K (1M + 64K) and length of 128K is issued.
After this operation the file size (and eof) at the receiver increases
from 1088K to 1216K (1088K + 128K);
4) Now there's still 768K (896K - 128K) of data left to clone or write, so
it checks for the next file extent item, located at file offset 384K.
This file extent item points to a different extent, not the one we want
to clone, with a length of 640K. So we issue a write operation into the
file range 1216K (1088K + 128K, end of the last clone operation), with
a length of 640K and with a data matching the one we can find for that
range in send root.
After this operation, the file size (and eof) at the receiver increases
from 1216K to 1856K (1216K + 640K);
5) Now there's still 128K (768K - 640K) of data left to clone or write, so
we look into the file extent item, which is for file offset 1M and it
points to the extent we want to clone, with a data offset of 64K and a
length of 960K.
However this matches the file offset we started with, the start of the
range to clone into. So we can't for sure find any file extent item
from here onwards with the rest of the data we want to clone, yet we
proceed and since the file extent item points to the shared extent,
with a data offset of 64K, we issue a clone operation with a source
range starting at file offset 1856K, which matches the file extent
item's offset, 1M, plus the amount of data cloned and written so far,
which is 64K (step 2) + 128K (step 3) + 640K (step 4). This clone
operation is invalid since the source range offset matches the current
eof of the file in the receiver. We should have stopped looking for
extents to clone at this point and instead fallback to write, which
would simply the contain the data in the file range from 1856K to
1856K + 128K.
So fix this by stopping the loop that looks for file ranges to clone at
clone_range() when we reach the current eof of the file being processed,
if we are cloning from the same file and using the send root as the clone
root. This ensures any data not yet cloned will be sent to the receiver
through a write operation.
A test case for fstests will follow soon.
Reported-by: Massimo B. <massimo.b@gmx.net>
Link: https://lore.kernel.org/linux-btrfs/6ae34776e85912960a253a8327068a892998e685.camel@gmx.net/
Fixes: 11f2069c11 ("Btrfs: send, allow clone operations within the same file")
CC: stable@vger.kernel.org # 5.5+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an incremental send, if we have a new inode that happens to
have the same number that an old directory inode had in the base snapshot
and that old directory has a pending rmdir operation, we end up computing
a wrong path for the new inode, causing the receiver to fail.
Example reproducer:
$ cat test-send-rmdir.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
mkdir $MNT/dir
touch $MNT/dir/file1
touch $MNT/dir/file2
touch $MNT/dir/file3
# Filesystem looks like:
#
# . (ino 256)
# |----- dir/ (ino 257)
# |----- file1 (ino 258)
# |----- file2 (ino 259)
# |----- file3 (ino 260)
#
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send -f /tmp/snap1.send $MNT/snap1
# Now remove our directory and all its files.
rm -fr $MNT/dir
# Unmount the filesystem and mount it again. This is to ensure that
# the next inode that is created ends up with the same inode number
# that our directory "dir" had, 257, which is the first free "objectid"
# available after mounting again the filesystem.
umount $MNT
mount $DEV $MNT
# Now create a new file (it could be a directory as well).
touch $MNT/newfile
# Filesystem now looks like:
#
# . (ino 256)
# |----- newfile (ino 257)
#
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2
# Now unmount the filesystem, create a new one, mount it and try to apply
# both send streams to recreate both snapshots.
umount $DEV
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
btrfs receive -f /tmp/snap1.send $MNT
btrfs receive -f /tmp/snap2.send $MNT
umount $MNT
When running the test, the receive operation for the incremental stream
fails:
$ ./test-send-rmdir.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: chown o257-9-0 failed: No such file or directory
So fix this by tracking directories that have a pending rmdir by inode
number and generation number, instead of only inode number.
A test case for fstests follows soon.
Reported-by: Massimo B. <massimo.b@gmx.net>
Tested-by: Massimo B. <massimo.b@gmx.net>
Link: https://lore.kernel.org/linux-btrfs/6ae34776e85912960a253a8327068a892998e685.camel@gmx.net/
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have helpers to access the on-disk item members, use that for
root_item::ctransid instead of raw le64_to_cpu.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
During an incremental send, when an inode has multiple new references we
might end up emitting rename operations for orphanizations that have a
source path that is no longer valid due to a previous orphanization of
some directory inode. This causes the receiver to fail since it tries
to rename a path that does not exists.
Example reproducer:
$ cat reproducer.sh
#!/bin/bash
mkfs.btrfs -f /dev/sdi >/dev/null
mount /dev/sdi /mnt/sdi
touch /mnt/sdi/f1
touch /mnt/sdi/f2
mkdir /mnt/sdi/d1
mkdir /mnt/sdi/d1/d2
# Filesystem looks like:
#
# . (ino 256)
# |----- f1 (ino 257)
# |----- f2 (ino 258)
# |----- d1/ (ino 259)
# |----- d2/ (ino 260)
btrfs subvolume snapshot -r /mnt/sdi /mnt/sdi/snap1
btrfs send -f /tmp/snap1.send /mnt/sdi/snap1
# Now do a series of changes such that:
#
# *) inode 258 has one new hardlink and the previous name changed
#
# *) both names conflict with the old names of two other inodes:
#
# 1) the new name "d1" conflicts with the old name of inode 259,
# under directory inode 256 (root)
#
# 2) the new name "d2" conflicts with the old name of inode 260
# under directory inode 259
#
# *) inodes 259 and 260 now have the old names of inode 258
#
# *) inode 257 is now located under inode 260 - an inode with a number
# smaller than the inode (258) for which we created a second hard
# link and swapped its names with inodes 259 and 260
#
ln /mnt/sdi/f2 /mnt/sdi/d1/f2_link
mv /mnt/sdi/f1 /mnt/sdi/d1/d2/f1
# Swap d1 and f2.
mv /mnt/sdi/d1 /mnt/sdi/tmp
mv /mnt/sdi/f2 /mnt/sdi/d1
mv /mnt/sdi/tmp /mnt/sdi/f2
# Swap d2 and f2_link
mv /mnt/sdi/f2/d2 /mnt/sdi/tmp
mv /mnt/sdi/f2/f2_link /mnt/sdi/f2/d2
mv /mnt/sdi/tmp /mnt/sdi/f2/f2_link
# Filesystem now looks like:
#
# . (ino 256)
# |----- d1 (ino 258)
# |----- f2/ (ino 259)
# |----- f2_link/ (ino 260)
# | |----- f1 (ino 257)
# |
# |----- d2 (ino 258)
btrfs subvolume snapshot -r /mnt/sdi /mnt/sdi/snap2
btrfs send -f /tmp/snap2.send -p /mnt/sdi/snap1 /mnt/sdi/snap2
mkfs.btrfs -f /dev/sdj >/dev/null
mount /dev/sdj /mnt/sdj
btrfs receive -f /tmp/snap1.send /mnt/sdj
btrfs receive -f /tmp/snap2.send /mnt/sdj
umount /mnt/sdi
umount /mnt/sdj
When executed the receive of the incremental stream fails:
$ ./reproducer.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: rename d1/d2 -> o260-6-0 failed: No such file or directory
This happens because:
1) When processing inode 257 we end up computing the name for inode 259
because it is an ancestor in the send snapshot, and at that point it
still has its old name, "d1", from the parent snapshot because inode
259 was not yet processed. We then cache that name, which is valid
until we start processing inode 259 (or set the progress to 260 after
processing its references);
2) Later we start processing inode 258 and collecting all its new
references into the list sctx->new_refs. The first reference in the
list happens to be the reference for name "d1" while the reference for
name "d2" is next (the last element of the list).
We compute the full path "d1/d2" for this second reference and store
it in the reference (its ->full_path member). The path used for the
new parent directory was "d1" and not "f2" because inode 259, the
new parent, was not yet processed;
3) When we start processing the new references at process_recorded_refs()
we start with the first reference in the list, for the new name "d1".
Because there is a conflicting inode that was not yet processed, which
is directory inode 259, we orphanize it, renaming it from "d1" to
"o259-6-0";
4) Then we start processing the new reference for name "d2", and we
realize it conflicts with the reference of inode 260 in the parent
snapshot. So we issue an orphanization operation for inode 260 by
emitting a rename operation with a destination path of "o260-6-0"
and a source path of "d1/d2" - this source path is the value we
stored in the reference earlier at step 2), corresponding to the
->full_path member of the reference, however that path is no longer
valid due to the orphanization of the directory inode 259 in step 3).
This makes the receiver fail since the path does not exists, it should
have been "o259-6-0/d2".
Fix this by recomputing the full path of a reference before emitting an
orphanization if we previously orphanized any directory, since that
directory could be a parent in the new path. This is a rare scenario so
keeping it simple and not checking if that previously orphanized directory
is in fact an ancestor of the inode we are trying to orphanize.
A test case for fstests follows soon.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an incremental send it is possible that when processing the new
references for an inode we end up issuing rename or link operations that
have an invalid path, which contains the orphanized name of a directory
before we actually orphanized it, causing the receiver to fail.
The following reproducer triggers such scenario:
$ cat reproducer.sh
#!/bin/bash
mkfs.btrfs -f /dev/sdi >/dev/null
mount /dev/sdi /mnt/sdi
touch /mnt/sdi/a
touch /mnt/sdi/b
mkdir /mnt/sdi/testdir
# We want "a" to have a lower inode number then "testdir" (257 vs 259).
mv /mnt/sdi/a /mnt/sdi/testdir/a
# Filesystem looks like:
#
# . (ino 256)
# |----- testdir/ (ino 259)
# | |----- a (ino 257)
# |
# |----- b (ino 258)
btrfs subvolume snapshot -r /mnt/sdi /mnt/sdi/snap1
btrfs send -f /tmp/snap1.send /mnt/sdi/snap1
# Now rename 259 to "testdir_2", then change the name of 257 to
# "testdir" and make it a direct descendant of the root inode (256).
# Also create a new link for inode 257 with the old name of inode 258.
# By swapping the names and location of several inodes and create a
# nasty dependency chain of rename and link operations.
mv /mnt/sdi/testdir/a /mnt/sdi/a2
touch /mnt/sdi/testdir/a
mv /mnt/sdi/b /mnt/sdi/b2
ln /mnt/sdi/a2 /mnt/sdi/b
mv /mnt/sdi/testdir /mnt/sdi/testdir_2
mv /mnt/sdi/a2 /mnt/sdi/testdir
# Filesystem now looks like:
#
# . (ino 256)
# |----- testdir_2/ (ino 259)
# | |----- a (ino 260)
# |
# |----- testdir (ino 257)
# |----- b (ino 257)
# |----- b2 (ino 258)
btrfs subvolume snapshot -r /mnt/sdi /mnt/sdi/snap2
btrfs send -f /tmp/snap2.send -p /mnt/sdi/snap1 /mnt/sdi/snap2
mkfs.btrfs -f /dev/sdj >/dev/null
mount /dev/sdj /mnt/sdj
btrfs receive -f /tmp/snap1.send /mnt/sdj
btrfs receive -f /tmp/snap2.send /mnt/sdj
umount /mnt/sdi
umount /mnt/sdj
When running the reproducer, the receive of the incremental send stream
fails:
$ ./reproducer.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: link b -> o259-6-0/a failed: No such file or directory
The problem happens because of the following:
1) Before we start iterating the list of new references for inode 257,
we generate its current path and store it at @valid_path, done at
the very beginning of process_recorded_refs(). The generated path
is "o259-6-0/a", containing the orphanized name for inode 259;
2) Then we iterate over the list of new references, which has the
references "b" and "testdir" in that specific order;
3) We process reference "b" first, because it is in the list before
reference "testdir". We then issue a link operation to create
the new reference "b" using a target path corresponding to the
content at @valid_path, which corresponds to "o259-6-0/a".
However we haven't yet orphanized inode 259, its name is still
"testdir", and not "o259-6-0". The orphanization of 259 did not
happen yet because we will process the reference named "testdir"
for inode 257 only in the next iteration of the loop that goes
over the list of new references.
Fix the issue by having a preliminar iteration over all the new references
at process_recorded_refs(). This iteration is responsible only for doing
the orphanization of other inodes that have and old reference that
conflicts with one of the new references of the inode we are currently
processing. The emission of rename and link operations happen now in the
next iteration of the new references.
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The header is mapped onto the send buffer and thus its members may be
potentially unaligned so use the helpers instead of directly assigning
the pointers. This has worked so far but let's use the helpers to make
that clear.
Signed-off-by: David Sterba <dsterba@suse.com>
Replace kvzalloc() call with kvcalloc() that also checks the size
internally. There's a standalone overflow check in the function so we
can return invalid parameter combination. Use array_size() helper to
compute the memory size for clone_sources_tmp.
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_ioctl_send() used open-coded kvzalloc implementation earlier.
The code was accidentally replaced with kzalloc() call [1]. Restore
the original code by using kvzalloc() to allocate sctx->clone_roots.
[1] https://patchwork.kernel.org/patch/9757891/#20529627
Fixes: 818e010bf9 ("btrfs: replace opencoded kvzalloc with the helper")
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
send_write_or_clone() basically has an open-coded copy of
btrfs_file_extent_end() except that it (incorrectly) aligns to PAGE_SIZE
instead of sectorsize. Fix and simplify the code by using
btrfs_file_extent_end().
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
send_write() currently copies from the page cache to sctx->read_buf, and
then from sctx->read_buf to sctx->send_buf. Similarly, send_hole()
zeroes sctx->read_buf and then copies from sctx->read_buf to
sctx->send_buf. However, if we write the TLV header manually, we can
copy to sctx->send_buf directly and get rid of sctx->read_buf.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
send_write()/fill_read_buf() have some logic for avoiding reading past
i_size. However, everywhere that we call
send_write()/send_extent_data(), we've already clamped the length down
to i_size. Get rid of the i_size handling, which simplifies the next
change.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There's a custom callback passed to btrfs_compare_trees which happens to
be named exactly same as the existing function implementing it. This is
confusing and the indirection is not necessary for our needs. Compiler
is clever enough to call it directly so there's effectively no change.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAl7U50AACgkQxWXV+ddt
WDtK1g//RXeNsTguYQr1N9R5eUPThjLEI0+4J0l4SYfCPU8Ou3C7nqpOEJJQgm8F
ezZE+16cWi9U5uGueOc+w0rfyz4AuIXKgzoz+c0/GG2+yV5jp6DsAMbWqojAb96L
V/N3HxEzR66jqwgVUBE/x5okb2SyY7//B1l/O0amc66XDO7KTMImpIwThere6zWZ
o2SNpYpHAPQeUYJQx8h+FAW3w1CxrCZmnifazU9Jqe9J7QeQLg7rbUlJDV38jySm
ZOA8ohKN9U1gPZy+dTU3kdyyuBIq1etkIaSPJANyTo5TczPKiC0IMg75cXtS4ae/
NSxhccMpSIjVMcIHARzSFGYKNP3sGNRsmaTUg/2Cx/9GoHOhYMiCAVc8qtBBpwJO
UI0siexrCe64RuTBMRRc128GdFv7IjmSImcdi8xaR62bCcUiNdEa3zvjRe/9tOEH
ET7Z85oBnKpSzpC3MdhSUU4dtHY5XLawP8z3oUU1VSzSWM2DVjlHf79/VzbOfp18
miCVpt94lCn/gUX7el6qcnbuvMAjDyeC6HmfD+TwzQgGwyV6TLgKN9lRXeH/Oy6/
VgjGQSavGHMll3zIGURmrBCXKudjJg0J+IP4wN1TimmSEMfwKH+7tnekQd8y5qlF
eXEIqlWNykKeDzEnmV9QJy+/cV83hVWM/mUslcTx39tLN/3B/Us=
=qTt8
-----END PGP SIGNATURE-----
Merge tag 'for-5.8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"Highlights:
- speedup dead root detection during orphan cleanup, eg. when there
are many deleted subvolumes waiting to be cleaned, the trees are
now looked up in radix tree instead of a O(N^2) search
- snapshot creation with inherited qgroup will mark the qgroup
inconsistent, requires a rescan
- send will emit file capabilities after chown, this produces a
stream that does not need postprocessing to set the capabilities
again
- direct io ported to iomap infrastructure, cleaned up and simplified
code, notably removing last use of struct buffer_head in btrfs code
Core changes:
- factor out backreference iteration, to be used by ordinary
backreferences and relocation code
- improved global block reserve utilization
* better logic to serialize requests
* increased maximum available for unlink
* improved handling on large pages (64K)
- direct io cleanups and fixes
* simplify layering, where cloned bios were unnecessarily created
for some cases
* error handling fixes (submit, endio)
* remove repair worker thread, used to avoid deadlocks during
repair
- refactored block group reading code, preparatory work for new type
of block group storage that should improve mount time on large
filesystems
Cleanups:
- cleaned up (and slightly sped up) set/get helpers for metadata data
structure members
- root bit REF_COWS got renamed to SHAREABLE to reflect the that the
blocks of the tree get shared either among subvolumes or with the
relocation trees
Fixes:
- when subvolume deletion fails due to ENOSPC, the filesystem is not
turned read-only
- device scan deals with devices from other filesystems that changed
ownership due to overwrite (mkfs)
- fix a race between scrub and block group removal/allocation
- fix long standing bug of a runaway balance operation, printing the
same line to the syslog, caused by a stale status bit on a reloc
tree that prevented progress
- fix corrupt log due to concurrent fsync of inodes with shared
extents
- fix space underflow for NODATACOW and buffered writes when it for
some reason needs to fallback to COW mode"
* tag 'for-5.8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (133 commits)
btrfs: fix space_info bytes_may_use underflow during space cache writeout
btrfs: fix space_info bytes_may_use underflow after nocow buffered write
btrfs: fix wrong file range cleanup after an error filling dealloc range
btrfs: remove redundant local variable in read_block_for_search
btrfs: open code key_search
btrfs: split btrfs_direct_IO to read and write part
btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK
fs: remove dio_end_io()
btrfs: switch to iomap_dio_rw() for dio
iomap: remove lockdep_assert_held()
iomap: add a filesystem hook for direct I/O bio submission
fs: export generic_file_buffered_read()
btrfs: turn space cache writeout failure messages into debug messages
btrfs: include error on messages about failure to write space/inode caches
btrfs: remove useless 'fail_unlock' label from btrfs_csum_file_blocks()
btrfs: do not ignore error from btrfs_next_leaf() when inserting checksums
btrfs: make checksum item extension more efficient
btrfs: fix corrupt log due to concurrent fsync of inodes with shared extents
btrfs: unexport btrfs_compress_set_level()
btrfs: simplify iget helpers
...
The inode lookup starting at btrfs_iget takes the full location key,
while only the objectid is used to match the inode, because the lookup
happens inside the given root thus the inode number is unique.
The entire location key is properly set up in btrfs_init_locked_inode.
Simplify the helpers and pass only inode number, renaming it to 'ino'
instead of 'objectid'. This allows to remove temporary variables key,
saving some stack space.
Signed-off-by: David Sterba <dsterba@suse.com>
The main function to lookup a root by its id btrfs_get_fs_root takes the
whole key, while only using the objectid. The value of offset is preset
to (u64)-1 but not actually used until btrfs_find_root that does the
actual search.
Switch btrfs_get_fs_root to use only objectid and remove all local
variables that existed just for the lookup. The actual key for search is
set up in btrfs_get_fs_root, reusing another key variable.
Signed-off-by: David Sterba <dsterba@suse.com>
Whenever a chown is executed, all capabilities of the file being touched
are lost. When doing incremental send with a file with capabilities,
there is a situation where the capability can be lost on the receiving
side. The sequence of actions bellow shows the problem:
$ mount /dev/sda fs1
$ mount /dev/sdb fs2
$ touch fs1/foo.bar
$ setcap cap_sys_nice+ep fs1/foo.bar
$ btrfs subvolume snapshot -r fs1 fs1/snap_init
$ btrfs send fs1/snap_init | btrfs receive fs2
$ chgrp adm fs1/foo.bar
$ setcap cap_sys_nice+ep fs1/foo.bar
$ btrfs subvolume snapshot -r fs1 fs1/snap_complete
$ btrfs subvolume snapshot -r fs1 fs1/snap_incremental
$ btrfs send fs1/snap_complete | btrfs receive fs2
$ btrfs send -p fs1/snap_init fs1/snap_incremental | btrfs receive fs2
At this point, only a chown was emitted by "btrfs send" since only the
group was changed. This makes the cap_sys_nice capability to be dropped
from fs2/snap_incremental/foo.bar
To fix that, only emit capabilities after chown is emitted. The current
code first checks for xattrs that are new/changed, emits them, and later
emit the chown. Now, __process_new_xattr skips capabilities, letting
only finish_inode_if_needed to emit them, if they exist, for the inode
being processed.
This behavior was being worked around in "btrfs receive" side by caching
the capability and only applying it after chown. Now, xattrs are only
emmited _after_ chown, making that workaround not needed anymore.
Link: https://github.com/kdave/btrfs-progs/issues/202
CC: stable@vger.kernel.org # 4.4+
Suggested-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we have proper root ref counting everywhere we can kill the
subvol_srcu.
* removal of fs_info::subvol_srcu reduces size of fs_info by 1176 bytes
* the refcount_t used for the references checks for accidental 0->1
in cases where the root lifetime would not be properly protected
* there's a leak detector for roots to catch unfreed roots at umount
time
* SRCU served us well over the years but is was not a proper
synchronization mechanism for some cases
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Getting the end offset for a file extent item requires a bit of code since
the extent can be either inline or regular/prealloc. There are some places
all over the code base that open code this logic and in another patch
later in this series it will be needed again. Therefore encapsulate this
logic in a helper function and use it.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We are now using these for all roots, rename them to btrfs_put_root()
and btrfs_grab_root();
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that all callers of btrfs_get_fs_root are subsequently calling
btrfs_grab_fs_root and handling dropping the ref when they are done
appropriately, go ahead and push btrfs_grab_fs_root up into
btrfs_get_fs_root.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We lookup all the clone roots and the parent root for send, so we need
to hold refs on all of these roots while we're processing them.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All this does is call btrfs_get_fs_root() with check_ref == true. Just
use btrfs_get_fs_root() so we don't have a bunch of different helpers
that do the same thing.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an incremental send and a file has extents shared with itself
at different file offsets, it's possible for send to emit clone operations
that will fail at the destination because the source range goes beyond the
file's current size. This happens when the file size has increased in the
send snapshot, there is a hole between the shared extents and both shared
extents are at file offsets which are greater the file's size in the
parent snapshot.
Example:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt/sdb
$ xfs_io -f -c "pwrite -S 0xf1 0 64K" /mnt/sdb/foobar
$ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/base
$ btrfs send -f /tmp/1.snap /mnt/sdb/base
# Create a 320K extent at file offset 512K.
$ xfs_io -c "pwrite -S 0xab 512K 64K" /mnt/sdb/foobar
$ xfs_io -c "pwrite -S 0xcd 576K 64K" /mnt/sdb/foobar
$ xfs_io -c "pwrite -S 0xef 640K 64K" /mnt/sdb/foobar
$ xfs_io -c "pwrite -S 0x64 704K 64K" /mnt/sdb/foobar
$ xfs_io -c "pwrite -S 0x73 768K 64K" /mnt/sdb/foobar
# Clone part of that 320K extent into a lower file offset (192K).
# This file offset is greater than the file's size in the parent
# snapshot (64K). Also the clone range is a bit behind the offset of
# the 320K extent so that we leave a hole between the shared extents.
$ xfs_io -c "reflink /mnt/sdb/foobar 448K 192K 192K" /mnt/sdb/foobar
$ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/incr
$ btrfs send -p /mnt/sdb/base -f /tmp/2.snap /mnt/sdb/incr
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt/sdc
$ btrfs receive -f /tmp/1.snap /mnt/sdc
$ btrfs receive -f /tmp/2.snap /mnt/sdc
ERROR: failed to clone extents to foobar: Invalid argument
The problem is that after processing the extent at file offset 256K, which
refers to the first 128K of the 320K extent created by the buffered write
operations, we have 'cur_inode_next_write_offset' set to 384K, which
corresponds to the end offset of the partially shared extent (256K + 128K)
and to the current file size in the receiver. Then when we process the
extent at offset 512K, we do extent backreference iteration to figure out
if we can clone the extent from some other inode or from the same inode,
and we consider the extent at offset 256K of the same inode as a valid
source for a clone operation, which is not correct because at that point
the current file size in the receiver is 384K, which corresponds to the
end of last processed extent (at file offset 256K), so using a clone
source range from 256K to 256K + 320K is invalid because that goes past
the current size of the file (384K) - this makes the receiver get an
-EINVAL error when attempting the clone operation.
So fix this by excluding clone sources that have a range that goes beyond
the current file size in the receiver when iterating extent backreferences.
A test case for fstests follows soon.
Fixes: 11f2069c11 ("Btrfs: send, allow clone operations within the same file")
CC: stable@vger.kernel.org # 5.5+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We log warning if root::orphan_cleanup_state is not set to
ORPHAN_CLEANUP_DONE in btrfs_ioctl_send(). However if the filesystem is
mounted as readonly we skip the orphan item cleanup during the lookup
and root::orphan_cleanup_state remains at the init state 0 instead of
ORPHAN_CLEANUP_DONE (2). So during send in btrfs_ioctl_send() we hit the
warning as below.
WARN_ON(send_root->orphan_cleanup_state != ORPHAN_CLEANUP_DONE);
WARNING: CPU: 0 PID: 2616 at /Volumes/ws/btrfs-devel/fs/btrfs/send.c:7090 btrfs_ioctl_send+0xb2f/0x18c0 [btrfs]
::
RIP: 0010:btrfs_ioctl_send+0xb2f/0x18c0 [btrfs]
::
Call Trace:
::
_btrfs_ioctl_send+0x7b/0x110 [btrfs]
btrfs_ioctl+0x150a/0x2b00 [btrfs]
::
do_vfs_ioctl+0xa9/0x620
? __fget+0xac/0xe0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x49/0x130
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reproducer:
mkfs.btrfs -fq /dev/sdb
mount /dev/sdb /btrfs
btrfs subvolume create /btrfs/sv1
btrfs subvolume snapshot -r /btrfs/sv1 /btrfs/ss1
umount /btrfs
mount -o ro /dev/sdb /btrfs
btrfs send /btrfs/ss1 -f /tmp/f
The warning exists because having orphan inodes could confuse send and
cause it to fail or produce incorrect streams. The two cases that would
cause such send failures, which are already fixed are:
1) Inodes that were unlinked - these are orphanized and remain with a
link count of 0. These caused send operations to fail because it
expected to always find at least one path for an inode. However this
is no longer a problem since send is now able to deal with such
inodes since commit 46b2f4590a ("Btrfs: fix send failure when root
has deleted files still open") and treats them as having been
completely removed (the state after an orphan cleanup is performed).
2) Inodes that were in the process of being truncated. These resulted in
send not knowing about the truncation and potentially issue write
operations full of zeroes for the range from the new file size to the
old file size. This is no longer a problem because we no longer
create orphan items for truncation since commit f7e9e8fc79 ("Btrfs:
stop creating orphan items for truncate").
As such before these commits, the WARN_ON here provided a clue in case
something went wrong. Instead of being a warning against the
root::orphan_cleanup_state value, it could have been more accurate by
checking if there were actually any orphan items, and then issue a
warning only if any exists, but that would be more expensive to check.
Since orphanized inodes no longer cause problems for send, just remove
the warning.
Reported-by: Christoph Anton Mitterer <calestyo@scientia.net>
Link: https://lore.kernel.org/linux-btrfs/21cb5e8d059f6e1496a903fa7bfc0a297e2f5370.camel@scientia.net/
CC: stable@vger.kernel.org # 4.19+
Suggested-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Backreference walking, which is used by send to figure if it can issue
clone operations instead of write operations, can be very slow and use
too much memory when extents have many references. This change simply
skips backreference walking when an extent has more than 64 references,
in which case we fallback to a write operation instead of a clone
operation. This limit is conservative and in practice I observed no
signicant slowdown with up to 100 references and still low memory usage
up to that limit.
This is a temporary workaround until there are speedups in the backref
walking code, and as such it does not attempt to add extra interfaces or
knobs to tweak the threshold.
Reported-by: Atemu <atemu.main@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CAE4GHgkvqVADtS4AzcQJxo0Q1jKQgKaW3JGp3SGdoinVo=C9eQ@mail.gmail.com/T/#me55dc0987f9cc2acaa54372ce0492c65782be3fa
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For send we currently skip clone operations when the source and
destination files are the same. This is so because clone didn't support
this case in its early days, but support for it was added back in May
2013 by commit a96fbc7288 ("Btrfs: allow file data clone within a
file"). This change adds support for it.
Example:
$ mkfs.btrfs -f /dev/sdd
$ mount /dev/sdd /mnt/sdd
$ xfs_io -f -c "pwrite -S 0xab -b 64K 0 64K" /mnt/sdd/foobar
$ xfs_io -c "reflink /mnt/sdd/foobar 0 64K 64K" /mnt/sdd/foobar
$ btrfs subvolume snapshot -r /mnt/sdd /mnt/sdd/snap
$ mkfs.btrfs -f /dev/sde
$ mount /dev/sde /mnt/sde
$ btrfs send /mnt/sdd/snap | btrfs receive /mnt/sde
Without this change file foobar at the destination has a single 128Kb
extent:
$ filefrag -v /mnt/sde/snap/foobar
Filesystem type is: 9123683e
File size of /mnt/sde/snap/foobar is 131072 (32 blocks of 4096 bytes)
ext: logical_offset: physical_offset: length: expected: flags:
0: 0.. 31: 0.. 31: 32: last,unknown_loc,delalloc,eof
/mnt/sde/snap/foobar: 1 extent found
With this we get a single 64Kb extent that is shared at file offsets 0
and 64K, just like in the source filesystem:
$ filefrag -v /mnt/sde/snap/foobar
Filesystem type is: 9123683e
File size of /mnt/sde/snap/foobar is 131072 (32 blocks of 4096 bytes)
ext: logical_offset: physical_offset: length: expected: flags:
0: 0.. 15: 3328.. 3343: 16: shared
1: 16.. 31: 3328.. 3343: 16: 3344: last,shared,eof
/mnt/sde/snap/foobar: 2 extents found
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The parameter is now always set to NULL and could be dropped. The last
user was get_default_root but that got reworked in 05dbe6837b ("Btrfs:
unify subvol= and subvolid= mounting") and the parameter became unused.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
GCC throws warning message as below:
‘clone_src_i_size’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
#define IS_ALIGNED(x, a) (((x) & ((typeof(x))(a) - 1)) == 0)
^
fs/btrfs/send.c:5088:6: note: ‘clone_src_i_size’ was declared here
u64 clone_src_i_size;
^
The clone_src_i_size is only used as call-by-reference
in a call to get_inode_info().
Silence the warning by initializing clone_src_i_size to 0.
Note that the warning is a false positive and reported by older versions
of GCC (eg. 7.x) but not eg 9.x. As there have been numerous people, the
patch is applied. Setting clone_src_i_size to 0 does not otherwise make
sense and would not do any action in case the code changes in the future.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add note ]
Signed-off-by: David Sterba <dsterba@suse.com>
When doing any form of incremental send the parent and the child trees
need to be compared via btrfs_compare_trees. This can result in long
loop chains without ever relinquishing the CPU. This causes softlockup
detector to trigger when comparing trees with a lot of items. Example
report:
watchdog: BUG: soft lockup - CPU#0 stuck for 24s! [snapperd:16153]
CPU: 0 PID: 16153 Comm: snapperd Not tainted 5.2.9-1-default #1 openSUSE Tumbleweed (unreleased)
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : __ll_sc_arch_atomic_sub_return+0x14/0x20
lr : btrfs_release_extent_buffer_pages+0xe0/0x1e8 [btrfs]
sp : ffff00001273b7e0
Call trace:
__ll_sc_arch_atomic_sub_return+0x14/0x20
release_extent_buffer+0xdc/0x120 [btrfs]
free_extent_buffer.part.0+0xb0/0x118 [btrfs]
free_extent_buffer+0x24/0x30 [btrfs]
btrfs_release_path+0x4c/0xa0 [btrfs]
btrfs_free_path.part.0+0x20/0x40 [btrfs]
btrfs_free_path+0x24/0x30 [btrfs]
get_inode_info+0xa8/0xf8 [btrfs]
finish_inode_if_needed+0xe0/0x6d8 [btrfs]
changed_cb+0x9c/0x410 [btrfs]
btrfs_compare_trees+0x284/0x648 [btrfs]
send_subvol+0x33c/0x520 [btrfs]
btrfs_ioctl_send+0x8a0/0xaf0 [btrfs]
btrfs_ioctl+0x199c/0x2288 [btrfs]
do_vfs_ioctl+0x4b0/0x820
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_common.constprop.0+0x7c/0x188
el0_svc_handler+0x34/0x90
el0_svc+0x8/0xc
Fix this by adding a call to cond_resched at the beginning of the main
loop in btrfs_compare_trees.
Fixes: 7069830a9e ("Btrfs: add btrfs_compare_trees function")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Send is the only user of tree_compare, we can move it there along with
the other helpers and definitions.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an incremental send operation we can fail if we previously did
deduplication operations against a file that exists in both snapshots. In
that case we will fail the send operation with -EIO and print a message
to dmesg/syslog like the following:
BTRFS error (device sdc): Send: inconsistent snapshot, found updated \
extent for inode 257 without updated inode item, send root is 258, \
parent root is 257
This requires that we deduplicate to the same file in both snapshots for
the same amount of times on each snapshot. The issue happens because a
deduplication only updates the iversion of an inode and does not update
any other field of the inode, therefore if we deduplicate the file on
each snapshot for the same amount of time, the inode will have the same
iversion value (stored as the "sequence" field on the inode item) on both
snapshots, therefore it will be seen as unchanged between in the send
snapshot while there are new/updated/deleted extent items when comparing
to the parent snapshot. This makes the send operation return -EIO and
print an error message.
Example reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
# Create our first file. The first half of the file has several 64Kb
# extents while the second half as a single 512Kb extent.
$ xfs_io -f -s -c "pwrite -S 0xb8 -b 64K 0 512K" /mnt/foo
$ xfs_io -c "pwrite -S 0xb8 512K 512K" /mnt/foo
# Create the base snapshot and the parent send stream from it.
$ btrfs subvolume snapshot -r /mnt /mnt/mysnap1
$ btrfs send -f /tmp/1.snap /mnt/mysnap1
# Create our second file, that has exactly the same data as the first
# file.
$ xfs_io -f -c "pwrite -S 0xb8 0 1M" /mnt/bar
# Create the second snapshot, used for the incremental send, before
# doing the file deduplication.
$ btrfs subvolume snapshot -r /mnt /mnt/mysnap2
# Now before creating the incremental send stream:
#
# 1) Deduplicate into a subrange of file foo in snapshot mysnap1. This
# will drop several extent items and add a new one, also updating
# the inode's iversion (sequence field in inode item) by 1, but not
# any other field of the inode;
#
# 2) Deduplicate into a different subrange of file foo in snapshot
# mysnap2. This will replace an extent item with a new one, also
# updating the inode's iversion by 1 but not any other field of the
# inode.
#
# After these two deduplication operations, the inode items, for file
# foo, are identical in both snapshots, but we have different extent
# items for this inode in both snapshots. We want to check this doesn't
# cause send to fail with an error or produce an incorrect stream.
$ xfs_io -r -c "dedupe /mnt/bar 0 0 512K" /mnt/mysnap1/foo
$ xfs_io -r -c "dedupe /mnt/bar 512K 512K 512K" /mnt/mysnap2/foo
# Create the incremental send stream.
$ btrfs send -p /mnt/mysnap1 -f /tmp/2.snap /mnt/mysnap2
ERROR: send ioctl failed with -5: Input/output error
This issue started happening back in 2015 when deduplication was updated
to not update the inode's ctime and mtime and update only the iversion.
Back then we would hit a BUG_ON() in send, but later in 2016 send was
updated to return -EIO and print the error message instead of doing the
BUG_ON().
A test case for fstests follows soon.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203933
Fixes: 1c919a5e13 ("btrfs: don't update mtime/ctime on deduped inodes")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Send always operates on read-only trees and always expected that while it
is in progress, nothing changes in those trees. Due to that expectation
and the fact that send is a read-only operation, it operates on commit
roots and does not hold transaction handles. However relocation can COW
nodes and leafs from read-only trees, which can cause unexpected failures
and crashes (hitting BUG_ONs). while send using a node/leaf, it gets
COWed, the transaction used to COW it is committed, a new transaction
starts, the extent previously used for that node/leaf gets allocated,
possibly for another tree, and the respective extent buffer' content
changes while send is still using it. When this happens send normally
fails with EIO being returned to user space and messages like the
following are found in dmesg/syslog:
[ 3408.699121] BTRFS error (device sdc): parent transid verify failed on 58703872 wanted 250 found 253
[ 3441.523123] BTRFS error (device sdc): did not find backref in send_root. inode=63211, offset=0, disk_byte=5222825984 found extent=5222825984
Other times, less often, we hit a BUG_ON() because an extent buffer that
send is using used to be a node, and while send is still using it, it
got COWed and got reused as a leaf while send is still using, producing
the following trace:
[ 3478.466280] ------------[ cut here ]------------
[ 3478.466282] kernel BUG at fs/btrfs/ctree.c:1806!
[ 3478.466965] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[ 3478.467635] CPU: 0 PID: 2165 Comm: btrfs Not tainted 5.0.0-btrfs-next-46 #1
[ 3478.468311] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[ 3478.469681] RIP: 0010:read_node_slot+0x122/0x130 [btrfs]
(...)
[ 3478.471758] RSP: 0018:ffffa437826bfaa0 EFLAGS: 00010246
[ 3478.472457] RAX: ffff961416ed7000 RBX: 000000000000003d RCX: 0000000000000002
[ 3478.473151] RDX: 000000000000003d RSI: ffff96141e387408 RDI: ffff961599b30000
[ 3478.473837] RBP: ffffa437826bfb8e R08: 0000000000000001 R09: ffffa437826bfb8e
[ 3478.474515] R10: ffffa437826bfa70 R11: 0000000000000000 R12: ffff9614385c8708
[ 3478.475186] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
[ 3478.475840] FS: 00007f8e0e9cc8c0(0000) GS:ffff9615b6a00000(0000) knlGS:0000000000000000
[ 3478.476489] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3478.477127] CR2: 00007f98b67a056e CR3: 0000000005df6005 CR4: 00000000003606f0
[ 3478.477762] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 3478.478385] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 3478.479003] Call Trace:
[ 3478.479600] ? do_raw_spin_unlock+0x49/0xc0
[ 3478.480202] tree_advance+0x173/0x1d0 [btrfs]
[ 3478.480810] btrfs_compare_trees+0x30c/0x690 [btrfs]
[ 3478.481388] ? process_extent+0x1280/0x1280 [btrfs]
[ 3478.481954] btrfs_ioctl_send+0x1037/0x1270 [btrfs]
[ 3478.482510] _btrfs_ioctl_send+0x80/0x110 [btrfs]
[ 3478.483062] btrfs_ioctl+0x13fe/0x3120 [btrfs]
[ 3478.483581] ? rq_clock_task+0x2e/0x60
[ 3478.484086] ? wake_up_new_task+0x1f3/0x370
[ 3478.484582] ? do_vfs_ioctl+0xa2/0x6f0
[ 3478.485075] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[ 3478.485552] do_vfs_ioctl+0xa2/0x6f0
[ 3478.486016] ? __fget+0x113/0x200
[ 3478.486467] ksys_ioctl+0x70/0x80
[ 3478.486911] __x64_sys_ioctl+0x16/0x20
[ 3478.487337] do_syscall_64+0x60/0x1b0
[ 3478.487751] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 3478.488159] RIP: 0033:0x7f8e0d7d4dd7
(...)
[ 3478.489349] RSP: 002b:00007ffcf6fb4908 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
[ 3478.489742] RAX: ffffffffffffffda RBX: 0000000000000105 RCX: 00007f8e0d7d4dd7
[ 3478.490142] RDX: 00007ffcf6fb4990 RSI: 0000000040489426 RDI: 0000000000000005
[ 3478.490548] RBP: 0000000000000005 R08: 00007f8e0d6f3700 R09: 00007f8e0d6f3700
[ 3478.490953] R10: 00007f8e0d6f39d0 R11: 0000000000000202 R12: 0000000000000005
[ 3478.491343] R13: 00005624e0780020 R14: 0000000000000000 R15: 0000000000000001
(...)
[ 3478.493352] ---[ end trace d5f537302be4f8c8 ]---
Another possibility, much less likely to happen, is that send will not
fail but the contents of the stream it produces may not be correct.
To avoid this, do not allow send and relocation (balance) to run in
parallel. In the long term the goal is to allow for both to be able to
run concurrently without any problems, but that will take a significant
effort in development and testing.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit 9678c54388 ("btrfs: Remove custom crc32c init code") removed
the btrfs_crc32c() function, because it was a duplicate of the crc32c()
library function we already have in the kernel.
Resurrect it as a shim wrapper over crc32c() to make following
transformations of the checksumming code in btrfs easier.
Also provide a btrfs_crc32_final() to ease following transformations.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an incremental send we can now issue clone operations with a
source range that ends at the source's file eof and with a destination
range that ends at an offset smaller then the destination's file eof.
If the eof of the source file is not aligned to the sector size of the
filesystem, the receiver will get a -EINVAL error when trying to do the
operation or, on older kernels, silently corrupt the destination file.
The corruption happens on kernels without commit ac765f83f1
("Btrfs: fix data corruption due to cloning of eof block"), while the
failure to clone happens on kernels with that commit.
Example reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt/sdb
$ xfs_io -f -c "pwrite -S 0xb1 0 2M" /mnt/sdb/foo
$ xfs_io -f -c "pwrite -S 0xc7 0 2M" /mnt/sdb/bar
$ xfs_io -f -c "pwrite -S 0x4d 0 2M" /mnt/sdb/baz
$ xfs_io -f -c "pwrite -S 0xe2 0 2M" /mnt/sdb/zoo
$ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/base
$ btrfs send -f /tmp/base.send /mnt/sdb/base
$ xfs_io -c "reflink /mnt/sdb/bar 1560K 500K 100K" /mnt/sdb/bar
$ xfs_io -c "reflink /mnt/sdb/bar 1560K 0 100K" /mnt/sdb/zoo
$ xfs_io -c "truncate 550K" /mnt/sdb/bar
$ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/incr
$ btrfs send -f /tmp/incr.send -p /mnt/sdb/base /mnt/sdb/incr
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt/sdc
$ btrfs receive -f /tmp/base.send /mnt/sdc
$ btrfs receive -vv -f /tmp/incr.send /mnt/sdc
(...)
truncate bar size=563200
utimes bar
clone zoo - source=bar source offset=512000 offset=0 length=51200
ERROR: failed to clone extents to zoo
Invalid argument
The failure happens because the clone source range ends at the eof of file
bar, 563200, which is not aligned to the filesystems sector size (4Kb in
this case), and the destination range ends at offset 0 + 51200, which is
less then the size of the file zoo (2Mb).
So fix this by detecting such case and instead of issuing a clone
operation for the whole range, do a clone operation for smaller range
that is sector size aligned followed by a write operation for the block
containing the eof. Here we will always be pessimistic and assume the
destination filesystem of the send stream has the largest possible sector
size (64Kb), since we have no way of determining it.
This fixes a recent regression introduced in kernel 5.2-rc1.
Fixes: 040ee6120c ("Btrfs: send, improve clone range")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When using the no-holes feature, if we have a file with prealloc extents
with a start offset beyond the file's eof, doing an incremental send can
cause corruption of the file due to incorrect hole detection. Such case
requires that the prealloc extent(s) exist in both the parent and send
snapshots, and that a hole is punched into the file that covers all its
extents that do not cross the eof boundary.
Example reproducer:
$ mkfs.btrfs -f -O no-holes /dev/sdb
$ mount /dev/sdb /mnt/sdb
$ xfs_io -f -c "pwrite -S 0xab 0 500K" /mnt/sdb/foobar
$ xfs_io -c "falloc -k 1200K 800K" /mnt/sdb/foobar
$ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/base
$ btrfs send -f /tmp/base.snap /mnt/sdb/base
$ xfs_io -c "fpunch 0 500K" /mnt/sdb/foobar
$ btrfs subvolume snapshot -r /mnt/sdb /mnt/sdb/incr
$ btrfs send -p /mnt/sdb/base -f /tmp/incr.snap /mnt/sdb/incr
$ md5sum /mnt/sdb/incr/foobar
816df6f64deba63b029ca19d880ee10a /mnt/sdb/incr/foobar
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt/sdc
$ btrfs receive -f /tmp/base.snap /mnt/sdc
$ btrfs receive -f /tmp/incr.snap /mnt/sdc
$ md5sum /mnt/sdc/incr/foobar
cf2ef71f4a9e90c2f6013ba3b2257ed2 /mnt/sdc/incr/foobar
--> Different checksum, because the prealloc extent beyond the
file's eof confused the hole detection code and it assumed
a hole starting at offset 0 and ending at the offset of the
prealloc extent (1200Kb) instead of ending at the offset
500Kb (the file's size).
Fix this by ensuring we never cross the file's size when issuing the
write operations for a hole.
Fixes: 16e7549f04 ("Btrfs: incompatible format change to remove hole extents")
CC: stable@vger.kernel.org # 3.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Send operates on read only trees and expects them to never change while it
is using them. This is part of its initial design, and this expection is
due to two different reasons:
1) When it was introduced, no operations were allowed to modifiy read-only
subvolumes/snapshots (including defrag for example).
2) It keeps send from having an impact on other filesystem operations.
Namely send does not need to keep locks on the trees nor needs to hold on
to transaction handles and delay transaction commits. This ends up being
a consequence of the former reason.
However the deduplication feature was introduced later (on September 2013,
while send was introduced in July 2012) and it allowed for deduplication
with destination files that belong to read-only trees (subvolumes and
snapshots).
That means that having a send operation (either full or incremental) running
in parallel with a deduplication that has the destination inode in one of
the trees used by the send operation, can result in tree nodes and leaves
getting freed and reused while send is using them. This problem is similar
to the problem solved for the root nodes getting freed and reused when a
snapshot is made against one tree that is currenly being used by a send
operation, fixed in commits [1] and [2]. These commits explain in detail
how the problem happens and the explanation is valid for any node or leaf
that is not the root of a tree as well. This problem was also discussed
and explained recently in a thread [3].
The problem is very easy to reproduce when using send with large trees
(snapshots) and just a few concurrent deduplication operations that target
files in the trees used by send. A stress test case is being sent for
fstests that triggers the issue easily. The most common error to hit is
the send ioctl return -EIO with the following messages in dmesg/syslog:
[1631617.204075] BTRFS error (device sdc): did not find backref in send_root. inode=63292, offset=0, disk_byte=5228134400 found extent=5228134400
[1631633.251754] BTRFS error (device sdc): parent transid verify failed on 32243712 wanted 24 found 27
The first one is very easy to hit while the second one happens much less
frequently, except for very large trees (in that test case, snapshots
with 100000 files having large xattrs to get deep and wide trees).
Less frequently, at least one BUG_ON can be hit:
[1631742.130080] ------------[ cut here ]------------
[1631742.130625] kernel BUG at fs/btrfs/ctree.c:1806!
[1631742.131188] invalid opcode: 0000 [#6] SMP DEBUG_PAGEALLOC PTI
[1631742.131726] CPU: 1 PID: 13394 Comm: btrfs Tainted: G B D W 5.0.0-rc8-btrfs-next-45 #1
[1631742.132265] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[1631742.133399] RIP: 0010:read_node_slot+0x122/0x130 [btrfs]
(...)
[1631742.135061] RSP: 0018:ffffb530021ebaa0 EFLAGS: 00010246
[1631742.135615] RAX: ffff93ac8912e000 RBX: 000000000000009d RCX: 0000000000000002
[1631742.136173] RDX: 000000000000009d RSI: ffff93ac564b0d08 RDI: ffff93ad5b48c000
[1631742.136759] RBP: ffffb530021ebb7d R08: 0000000000000001 R09: ffffb530021ebb7d
[1631742.137324] R10: ffffb530021eba70 R11: 0000000000000000 R12: ffff93ac87d0a708
[1631742.137900] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000001
[1631742.138455] FS: 00007f4cdb1528c0(0000) GS:ffff93ad76a80000(0000) knlGS:0000000000000000
[1631742.139010] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1631742.139568] CR2: 00007f5acb3d0420 CR3: 000000012be3e006 CR4: 00000000003606e0
[1631742.140131] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[1631742.140719] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[1631742.141272] Call Trace:
[1631742.141826] ? do_raw_spin_unlock+0x49/0xc0
[1631742.142390] tree_advance+0x173/0x1d0 [btrfs]
[1631742.142948] btrfs_compare_trees+0x268/0x690 [btrfs]
[1631742.143533] ? process_extent+0x1070/0x1070 [btrfs]
[1631742.144088] btrfs_ioctl_send+0x1037/0x1270 [btrfs]
[1631742.144645] _btrfs_ioctl_send+0x80/0x110 [btrfs]
[1631742.145161] ? trace_sched_stick_numa+0xe0/0xe0
[1631742.145685] btrfs_ioctl+0x13fe/0x3120 [btrfs]
[1631742.146179] ? account_entity_enqueue+0xd3/0x100
[1631742.146662] ? reweight_entity+0x154/0x1a0
[1631742.147135] ? update_curr+0x20/0x2a0
[1631742.147593] ? check_preempt_wakeup+0x103/0x250
[1631742.148053] ? do_vfs_ioctl+0xa2/0x6f0
[1631742.148510] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[1631742.148942] do_vfs_ioctl+0xa2/0x6f0
[1631742.149361] ? __fget+0x113/0x200
[1631742.149767] ksys_ioctl+0x70/0x80
[1631742.150159] __x64_sys_ioctl+0x16/0x20
[1631742.150543] do_syscall_64+0x60/0x1b0
[1631742.150931] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[1631742.151326] RIP: 0033:0x7f4cd9f5add7
(...)
[1631742.152509] RSP: 002b:00007ffe91017708 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
[1631742.152892] RAX: ffffffffffffffda RBX: 0000000000000105 RCX: 00007f4cd9f5add7
[1631742.153268] RDX: 00007ffe91017790 RSI: 0000000040489426 RDI: 0000000000000007
[1631742.153633] RBP: 0000000000000007 R08: 00007f4cd9e79700 R09: 00007f4cd9e79700
[1631742.153999] R10: 00007f4cd9e799d0 R11: 0000000000000202 R12: 0000000000000003
[1631742.154365] R13: 0000555dfae53020 R14: 0000000000000000 R15: 0000000000000001
(...)
[1631742.156696] ---[ end trace 5dac9f96dcc3fd6b ]---
That BUG_ON happens because while send is using a node, that node is COWed
by a concurrent deduplication, gets freed and gets reused as a leaf (because
a transaction commit happened in between), so when it attempts to read a
slot from the extent buffer, at ctree.c:read_node_slot(), the extent buffer
contents were wiped out and it now matches a leaf (which can even belong to
some other tree now), hitting the BUG_ON(level == 0).
Fix this concurrency issue by not allowing send and deduplication to run
in parallel if both operate on the same readonly trees, returning EAGAIN
to user space and logging an exlicit warning in dmesg/syslog.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=be6821f82c3cc36e026f5afd10249988852b35ea
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6f2f0b394b54e2b159ef969a0b5274e9bbf82ff2
[3] https://lore.kernel.org/linux-btrfs/CAL3q7H7iqSEEyFaEtpRZw3cp613y+4k2Q8b4W7mweR3tZA05bQ@mail.gmail.com/
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we set a subvolume to read-only mode we do not flush dellaloc for any
of its inodes (except if the filesystem is mounted with -o flushoncommit),
since it does not affect correctness for any subsequent operations - except
for a future send operation. The send operation will not be able to see the
delalloc data since the respective file extent items, inode item updates,
backreferences, etc, have not hit yet the subvolume and extent trees.
Effectively this means data loss, since the send stream will not contain
any data from existing delalloc. Another problem from this is that if the
writeback starts and finishes while the send operation is in progress, we
have the subvolume tree being being modified concurrently which can result
in send failing unexpectedly with EIO or hitting runtime errors, assertion
failures or hitting BUG_ONs, etc.
Simple reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ btrfs subvolume create /mnt/sv
$ xfs_io -f -c "pwrite -S 0xea 0 108K" /mnt/sv/foo
$ btrfs property set /mnt/sv ro true
$ btrfs send -f /tmp/send.stream /mnt/sv
$ od -t x1 -A d /mnt/sv/foo
0000000 ea ea ea ea ea ea ea ea ea ea ea ea ea ea ea ea
*
0110592
$ umount /mnt
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ btrfs receive -f /tmp/send.stream /mnt
$ echo $?
0
$ od -t x1 -A d /mnt/sv/foo
0000000
# ---> empty file
Since this a problem that affects send only, fix it in send by flushing
dellaloc for all the roots used by the send operation before send starts
to process the commit roots.
This is a problem that affects send since it was introduced (commit
31db9f7c23 ("Btrfs: introduce BTRFS_IOC_SEND for btrfs send/receive"))
but backporting it to older kernels has some dependencies:
- For kernels between 3.19 and 4.20, it depends on commit 3cd24c6980
("btrfs: use tagged writepage to mitigate livelock of snapshot") because
the function btrfs_start_delalloc_snapshot() does not exist before that
commit. So one has to either pick that commit or replace the calls to
btrfs_start_delalloc_snapshot() in this patch with calls to
btrfs_start_delalloc_inodes().
- For kernels older than 3.19 it also requires commit e5fa8f865b
("Btrfs: ensure send always works on roots without orphans") because
it depends on the function ensure_commit_roots_uptodate() which that
commits introduced.
- No dependencies for 5.0+ kernels.
A test case for fstests follows soon.
CC: stable@vger.kernel.org # 3.19+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Improve clone_range in two scenarios.
1. Remove the limit of inode size when find clone inodes We can do
partial clone, so there is no need to limit the size of the candidate
inode. When clone a range, we clone the legal range only by bytenr,
offset, len, inode size.
2. In the scenarios of rewrite or clone_range, data_offset rarely
matches exactly, so the chance of a clone is missed.
e.g.
1. Write a 1M file
dd if=/dev/zero of=1M bs=1M count=1
2. Clone 1M file
cp --reflink 1M clone
3. Rewrite 4k on the clone file
dd if=/dev/zero of=clone bs=4k count=1 conv=notrunc
The disk layout is as follows:
item 16 key (257 EXTENT_DATA 0) itemoff 15353 itemsize 53
extent data disk byte 1103101952 nr 1048576
extent data offset 0 nr 1048576 ram 1048576
extent compression(none)
...
item 22 key (258 EXTENT_DATA 0) itemoff 14959 itemsize 53
extent data disk byte 1104150528 nr 4096
extent data offset 0 nr 4096 ram 4096
extent compression(none)
item 23 key (258 EXTENT_DATA 4096) itemoff 14906 itemsize 53
extent data disk byte 1103101952 nr 1048576
extent data offset 4096 nr 1044480 ram 1048576
extent compression(none)
When send, inode 258 file offset 4096~1048576 (item 23) has a chance to
clone_range, but because data_offset does not match inode 257 (item 16),
it causes missed clone and can only transfer actual data.
Improve the problem by judging whether the current data_offset has
overlap with the file extent item, and if so, adjusting offset and
extent_len so that we can clone correctly.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Robbie Ko <robbieko@synology.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The typos accumulate over time so once in a while time they get fixed in
a large patch.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Constructs like 'var & (PAGE_SIZE - 1)' or 'var & ~PAGE_MASK' can denote an
offset into a page.
So replace them by the offset_in_page() macro instead of open-coding it if
they're not used as an alignment check.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When doing an incremental send, due to the need of delaying directory move
(rename) operations we can end up in infinite loop at
apply_children_dir_moves().
An example scenario that triggers this problem is described below, where
directory names correspond to the numbers of their respective inodes.
Parent snapshot:
.
|--- 261/
|--- 271/
|--- 266/
|--- 259/
|--- 260/
| |--- 267
|
|--- 264/
| |--- 258/
| |--- 257/
|
|--- 265/
|--- 268/
|--- 269/
| |--- 262/
|
|--- 270/
|--- 272/
| |--- 263/
| |--- 275/
|
|--- 274/
|--- 273/
Send snapshot:
.
|-- 275/
|-- 274/
|-- 273/
|-- 262/
|-- 269/
|-- 258/
|-- 271/
|-- 268/
|-- 267/
|-- 270/
|-- 259/
| |-- 265/
|
|-- 272/
|-- 257/
|-- 260/
|-- 264/
|-- 263/
|-- 261/
|-- 266/
When processing inode 257 we delay its move (rename) operation because its
new parent in the send snapshot, inode 272, was not yet processed. Then
when processing inode 272, we delay the move operation for that inode
because inode 274 is its ancestor in the send snapshot. Finally we delay
the move operation for inode 274 when processing it because inode 275 is
its new parent in the send snapshot and was not yet moved.
When finishing processing inode 275, we start to do the move operations
that were previously delayed (at apply_children_dir_moves()), resulting in
the following iterations:
1) We issue the move operation for inode 274;
2) Because inode 262 depended on the move operation of inode 274 (it was
delayed because 274 is its ancestor in the send snapshot), we issue the
move operation for inode 262;
3) We issue the move operation for inode 272, because it was delayed by
inode 274 too (ancestor of 272 in the send snapshot);
4) We issue the move operation for inode 269 (it was delayed by 262);
5) We issue the move operation for inode 257 (it was delayed by 272);
6) We issue the move operation for inode 260 (it was delayed by 272);
7) We issue the move operation for inode 258 (it was delayed by 269);
8) We issue the move operation for inode 264 (it was delayed by 257);
9) We issue the move operation for inode 271 (it was delayed by 258);
10) We issue the move operation for inode 263 (it was delayed by 264);
11) We issue the move operation for inode 268 (it was delayed by 271);
12) We verify if we can issue the move operation for inode 270 (it was
delayed by 271). We detect a path loop in the current state, because
inode 267 needs to be moved first before we can issue the move
operation for inode 270. So we delay again the move operation for
inode 270, this time we will attempt to do it after inode 267 is
moved;
13) We issue the move operation for inode 261 (it was delayed by 263);
14) We verify if we can issue the move operation for inode 266 (it was
delayed by 263). We detect a path loop in the current state, because
inode 270 needs to be moved first before we can issue the move
operation for inode 266. So we delay again the move operation for
inode 266, this time we will attempt to do it after inode 270 is
moved (its move operation was delayed in step 12);
15) We issue the move operation for inode 267 (it was delayed by 268);
16) We verify if we can issue the move operation for inode 266 (it was
delayed by 270). We detect a path loop in the current state, because
inode 270 needs to be moved first before we can issue the move
operation for inode 266. So we delay again the move operation for
inode 266, this time we will attempt to do it after inode 270 is
moved (its move operation was delayed in step 12). So here we added
again the same delayed move operation that we added in step 14;
17) We attempt again to see if we can issue the move operation for inode
266, and as in step 16, we realize we can not due to a path loop in
the current state due to a dependency on inode 270. Again we delay
inode's 266 rename to happen after inode's 270 move operation, adding
the same dependency to the empty stack that we did in steps 14 and 16.
The next iteration will pick the same move dependency on the stack
(the only entry) and realize again there is still a path loop and then
again the same dependency to the stack, over and over, resulting in
an infinite loop.
So fix this by preventing adding the same move dependency entries to the
stack by removing each pending move record from the red black tree of
pending moves. This way the next call to get_pending_dir_moves() will
not return anything for the current parent inode.
A test case for fstests, with this reproducer, follows soon.
Signed-off-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
[Wrote changelog with example and more clear explanation]
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
