[ Upstream commit b8a039d377 ]
RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS
(Dynamic Voltage Scaling). These GPIOs are entirely optional but a
dev_warn() appeared when cleaning this driver to use a more up-to-date
gpiod API. At least reduce the log level to 'info' as it is totally
fine to not populate these GPIO on a hardware design.
This change is trivial but it is worth not polluting the logs during
bringup phase by having real warnings and errors sorted out
correctly.
Fixes: a13eaf02e2 ("regulator: rk808: make better use of the gpiod API")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6605f0ca3a ]
This patch adds the driver data and updates quirk info
for tgl with max98357a speaker amp and ALC5682 headset codec.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191126143205.21987-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68e07970e ]
TGL supports one more HDMI DAI than previous models.
So add quirk support for number of HDMI DAI's.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191126143205.21987-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf08949cc8 ]
While running kprobe module test, find_module_all() caused
a suspicious RCU usage warning.
-----
=============================
WARNING: suspicious RCU usage
5.4.0-next-20191202+ #63 Not tainted
-----------------------------
kernel/module.c:619 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by rmmod/642:
#0: ffffffff8227da80 (module_mutex){+.+.}, at: __x64_sys_delete_module+0x9a/0x230
stack backtrace:
CPU: 0 PID: 642 Comm: rmmod Not tainted 5.4.0-next-20191202+ #63
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
dump_stack+0x71/0xa0
find_module_all+0xc1/0xd0
__x64_sys_delete_module+0xac/0x230
? do_syscall_64+0x12/0x1f0
do_syscall_64+0x50/0x1f0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4b6d49
-----
This is because list_for_each_entry_rcu(modules) is called
without rcu_read_lock(). This is safe because the module_mutex
is locked.
Pass lockdep_is_held(&module_mutex) to the list_for_each_entry_rcu()
to suppress this warning, This also fixes similar issue in
mod_find() and each_symbol_section().
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a793e19c15 ]
Although it appeared to follow logically from the bindings, apparently
the thermal framework can't properly cope with a single cooling device
being shared between multiple maps. The CPU zone is probably easier to
overheat, so remove the references to the (optional) fan from the GPU
cooling zone to avoid things getting confused. Hopefully GPU-intensive
tasks will leak enough heat across to the CPU zone to still hit the
fan trips before reaching critical GPU temperatures.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/5bb39f3115df1a487d717d3ae87e523b03749379.1573908197.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d35408afb ]
Previously, there was an omap panel-dpi driver that would
read generic timings from the device tree and set the display
timing accordingly. This driver was removed so the screen
no longer functions. This patch modifies the panel-simple
file to setup the timings to the same values previously used.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191016135147.7743-1-aford173@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a63141e317 ]
Commit b0f3cd3191 ("drm/amdgpu: remove unnecessary JPEG2.0 code from
VCN2.0") introduced a new clang warning in the vcn_v2_0_stop function:
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: warning: variable 'r'
is used uninitialized whenever 'while' loop exits because its condition
is false [-Wsometimes-uninitialized]
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1083:6: note: uninitialized use
occurs here
if (r)
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: note: remove the
condition if it is always true
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1072:7: note: initialize the
variable 'r' to silence this warning
int r;
^
= 0
1 warning generated.
To prevent warnings like this from happening in the future, make the
SOC15_WAIT_ON_RREG macro initialize its ret variable before the while
loop that can time out. This macro's return value is always checked so
it should set ret in both the success and fail path.
Link: https://github.com/ClangBuiltLinux/linux/issues/776
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e01cc82c4d ]
the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bae028e3e5 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c: In function
'amdgpu_atombios_get_connector_info_from_object_table':
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:26: warning: variable
'grph_obj_num' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:13: warning: variable
'grph_obj_id' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:37: warning: variable
'con_obj_type' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:24: warning: variable
'con_obj_num' set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Fixes: d38ceaf99e ("drm/amdgpu: add core driver (v4)")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b2dc83906 ]
We need to have a synchronize_rcu before free'ing the sockhash because any
outstanding psock references will have a pointer to the map and when they
use it, this could trigger a use after free.
This is a sister fix for sockhash, following commit 2bb90e5cc9 ("bpf:
sockmap, synchronize_rcu before free'ing map") which addressed sockmap,
which comes from a manual audit.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200206111652.694507-3-jakub@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f38abc15d1 ]
The sdma_queue_count increment should be done before
execute_queues_cpsch(), which calls pm_calc_rlib_size() where
sdma_queue_count is used to calculate whether over_subscription is
triggered.
With the previous code, when a SDMA queue is created,
compute_queue_count in pm_calc_rlib_size() is one more than the
actual compute queue number, because the queue_count has been
incremented while sdma_queue_count has not. This patch fixes that.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 908b050114 ]
When I got my clock parenting slightly wrong I ended up with a crash
that looked like this:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
...
pc : clk_hw_get_rate+0x14/0x44
...
Call trace:
clk_hw_get_rate+0x14/0x44
_freq_tbl_determine_rate+0x94/0xfc
clk_rcg2_determine_rate+0x2c/0x38
clk_core_determine_round_nolock+0x4c/0x88
clk_core_round_rate_nolock+0x6c/0xa8
clk_core_round_rate_nolock+0x9c/0xa8
clk_core_set_rate_nolock+0x70/0x180
clk_set_rate+0x3c/0x6c
of_clk_set_defaults+0x254/0x360
platform_drv_probe+0x28/0xb0
really_probe+0x120/0x2dc
driver_probe_device+0x64/0xfc
device_driver_attach+0x4c/0x6c
__driver_attach+0xac/0xc0
bus_for_each_dev+0x84/0xcc
driver_attach+0x2c/0x38
bus_add_driver+0xfc/0x1d0
driver_register+0x64/0xf8
__platform_driver_register+0x4c/0x58
msm_drm_register+0x5c/0x60
...
It turned out that clk_hw_get_parent_by_index() was returning NULL and
we weren't checking. Let's check it so that we don't crash.
Fixes: ac269395cd ("clk: qcom: Convert to clk_hw based provider APIs")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.1.I7487325fe8e701a68a07d3be8a6a4b571eca9cfa@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21e157c62e ]
The DFS frequency table logic overwrites 'cfg' while detecting the
parent clk and then later on in clk_rcg2_dfs_populate_freq() we use that
same variable to figure out the mode of the clk, either MND or not. Add
a new variable to hold the parent clk bit so that 'cfg' is left
untouched for use later.
This fixes problems in detecting the supported frequencies for any clks
in DFS mode.
Fixes: cc4f6944d0 ("clk: qcom: Add support for RCG to register for DFS")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200128193329.45635-1-sboyd@kernel.org
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8fb7d7e48 ]
Running randconfig on arm64 using KCONFIG_SEED=0x40C5E904 (e.g. on v5.5)
produces the .config with CONFIG_EFI=y and CONFIG_CPU_BIG_ENDIAN=y,
which does not meet the !CONFIG_CPU_BIG_ENDIAN dependency.
This is because the user choice for CONFIG_CPU_LITTLE_ENDIAN vs
CONFIG_CPU_BIG_ENDIAN is set by randomize_choice_values() after the
value of CONFIG_EFI is calculated.
When this happens, the has_changed flag should be set.
Currently, it takes the result from the last iteration. It should
accumulate all the results of the loop.
Fixes: 3b9a19e089 ("kconfig: loop as long as we changed some symbols in randconfig")
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f718b09327 ]
Commit 478de3380c ("block, bfq: deschedule empty bfq_queues not
referred by any process") fixed commit 3726112ec7 ("block, bfq:
re-schedule empty queues if they deserve I/O plugging") by
descheduling an empty bfq_queue when it remains with not process
reference. Yet, this still left a case uncovered: an empty bfq_queue
with not process reference that remains in service. This happens for
an in-service sync bfq_queue that is deemed to deserve I/O-dispatch
plugging when it remains empty. Yet no new requests will arrive for
such a bfq_queue if no process sends requests to it any longer. Even
worse, the bfq_queue may happen to be prematurely freed while still in
service (because there may remain no reference to it any longer).
This commit solves this problem by preventing I/O dispatch from being
plugged for the in-service bfq_queue, if the latter has no process
reference (the bfq_queue is then prevented from remaining in service).
Fixes: 3726112ec7 ("block, bfq: re-schedule empty queues if they deserve I/O plugging")
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Patrick Dung <patdung100@gmail.com>
Tested-by: Patrick Dung <patdung100@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b82a051c1 ]
Currently when an error code -EIO or -ENOSPC in the for-loop of
writeback_store the error code is being overwritten by a ret = len
assignment at the end of the function and the error codes are being
lost. Fix this by assigning ret = len at the start of the function and
remove the assignment from the end, hence allowing ret to be preserved
when error codes are assigned to it.
Addresses Coverity ("Unused value")
Link: http://lkml.kernel.org/r/20191128122958.178290-1-colin.king@canonical.com
Fixes: a939888ec3 ("zram: support idle/huge page writeback")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f3c50219 ]
For COW, btrfs expects pages dirty pages to have been through a few setup
steps. This includes reserving space for the new block allocations and marking
the range in the state tree for delayed allocation.
A few places outside btrfs will dirty pages directly, especially when unmapping
mmap'd pages. In order for these to properly go through COW, we run them
through a fixup worker to wait for stable pages, and do the delalloc prep.
87826df0ec added a window where the dirty pages were cleaned, but pending
more action from the fixup worker. We clear_page_dirty_for_io() before
we call into writepage, so the page is no longer dirty. The commit
changed it so now we leave the page clean between unlocking it here and
the fixup worker starting at some point in the future.
During this window, page migration can jump in and relocate the page. Once our
fixup work actually starts, it finds page->mapping is NULL and we end up
freeing the page without ever writing it.
This leads to crc errors and other exciting problems, since it screws up the
whole statemachine for waiting for ordered extents. The fix here is to keep
the page dirty while we're waiting for the fixup worker to get to work.
This is accomplished by returning -EAGAIN from btrfs_writepage_cow_fixup
if we queued the page up for fixup, which will cause the writepage
function to redirty the page.
Because we now expect the page to be dirty once it gets to the fixup
worker we must adjust the error cases to call clear_page_dirty_for_io()
on the page. That is the bulk of the patch, but it is not the fix, the
fix is the -EAGAIN from btrfs_writepage_cow_fixup. We cannot separate
these two changes out because the error conditions change with the new
expectations.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c0dd228b5 ]
When kzalloc fail, may cause trying to destroy the
workqueue from inside the workqueue.
If num_connections is m (2 < m), and NO.1 ~ NO.n
(1 < n < m) kzalloc are successful. The NO.(n + 1)
failed. Then, nbd_start_device will return ENOMEM
to nbd_start_device_ioctl, and nbd_start_device_ioctl
will return immediately without running flush_workqueue.
However, we still have n recv threads. If nbd_release
run first, recv threads may have to drop the last
config_refs and try to destroy the workqueue from
inside the workqueue.
To fix it, add a flush_workqueue in nbd_start_device.
Fixes: e9e006f5fc ("nbd: fix max number of supported devs")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b527b638fd ]
In the process of adding better error messages for sorting, I realized
that strsep was being used incorrectly and some of the error paths I
was expecting to be hit weren't and just fell through to the common
invalid key error case.
It also became obvious that for keyword assignments, it wasn't
necessary to save the full assignment and reparse it later, and having
a common empty-assignment check would also make more sense in terms of
error processing.
Change the code to fix these problems and simplify it for new error
message changes in a subsequent patch.
Link: http://lkml.kernel.org/r/1c3ef0b6655deaf345f6faee2584a0298ac2d743.1561743018.git.zanussi@kernel.org
Fixes: e62347d245 ("tracing: Add hist trigger support for user-defined sorting ('sort=' param)")
Fixes: 7ef224d1d0 ("tracing: Add 'hist' event trigger command")
Fixes: a4072fe85b ("tracing: Add a clock attribute for hist triggers")
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eb6d7aca5 ]
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34719de919 ]
Merely enabling I2C and RTC selects REGMAP_I2C and REGMAP_SPI, even when
no driver needs it. While the former can be moduler, the latter cannot,
and thus becomes built-in.
Fix this by moving the select statements for REGMAP_I2C and REGMAP_SPI
from the RTC_I2C_AND_SPI helper to the individual drivers that depend on
it.
Note that the comment for RTC_I2C_AND_SPI refers to SND_SOC_I2C_AND_SPI
for more information, but the latter does not select REGMAP_{I2C,SPI}
itself, and defers that to the individual drivers, too.
Fixes: 080481f54e ("rtc: merge ds3232 and ds3234")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200112171349.22268-1-geert@linux-m68k.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac87813d43 ]
Commit 852c8cbf34 ("selftests/kselftest/runner.sh: Add 45 second
timeout per test") adds support for a new per-test-directory "settings"
file. But this only works for tests not in a sub-subdirectories, e.g.
- tools/testing/selftests/rtc (rtc) is OK,
- tools/testing/selftests/net/mptcp (net/mptcp) is not.
We have to increase the timeout for net/mptcp tests which are not
upstreamed yet but this fix is valid for other tests if they need to add
a "settings" file, see the full list with:
tools/testing/selftests/*/*/**/Makefile
Note that this patch changes the text header message printed at the end
of the execution but this text is modified only for the tests that are
in sub-subdirectories, e.g.
ok 1 selftests: net/mptcp: mptcp_connect.sh
Before we had:
ok 1 selftests: mptcp: mptcp_connect.sh
But showing the full target name is probably better, just in case a
subsubdir has the same name as another one in another subdirectory.
Fixes: 852c8cbf34 (selftests/kselftest/runner.sh: Add 45 second timeout per test)
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c8e60fb86 ]
Commit 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling
brcmf_bus_started()") changed the initialization order of the brcmfmac
SDIO driver. Unfortunately since brcmf_sdiod_intr_register() is now
called before the sdiodev->bus_if initialization, it reads the wrong
chip ID and fails to initialize the GPIO on brcm43362. Thus the chip
cannot send interrupts and fails to probe:
[ 12.517023] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
[ 12.531214] ieee80211 phy0: brcmf_bus_started: failed: -110
[ 12.536976] ieee80211 phy0: brcmf_attach: dongle is not responding: err=-110
[ 12.566467] brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
Initialize the bus interface earlier to ensure that
brcmf_sdiod_intr_register() properly sets up the OOB interrupt.
BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908438
Fixes: 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling brcmf_bus_started()")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a68fa5f9 ]
The rate mask is used to tell firmware the supported rate depends on
negotiation. We loop 2 times for all VHT/HT 2SS rate mask first, and then
only keep the part according to chip's NSS.
This commit fixes the logic error of '&' operations for VHT/HT rate, and
we should run this logic before adding legacy rate.
To access HT MCS map, index 0/1 represent MCS 0-7/8-15 respectively. Use
NL80211_BAND_xxx is incorrect, so fix it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba8b3b6bd ]
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
We might see a trace like below
[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c
Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: dc405152bb ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51f57b01e4 ]
JBD2_REC_ERR flag used to indicate the errno has been updated when jbd2
aborted, and then __ext4_abort() and ext4_handle_error() can invoke
panic if ERRORS_PANIC is specified. But if the journal has been aborted
with zero errno, jbd2_journal_abort() didn't set this flag so we can
no longer panic. Fix this by always record the proper errno in the
journal superblock.
Fixes: 4327ba52af ("ext4, jbd2: ensure entering into panic after recording an error in superblock")
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191204124614.45424-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc420c6cee ]
Kmemleak relies on specific symbols to register the read only data
during init (e.g. __start_ro_after_init).
Trying to build an XIP kernel on arm results in the linking error
reported below because when this option is selected read only data
after init are not allowed since .data is read only (.rodata).
arm-linux-gnueabihf-ld: mm/kmemleak.o: in function `kmemleak_init':
kmemleak.c:(.init.text+0x148): undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x14c):
undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x150):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x156):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x162):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x16a):
undefined reference to `__start_ro_after_init'
linux/Makefile:1078: recipe for target 'vmlinux' failed
Fix the issue enabling kmemleak only on non XIP kernels.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfb6cd1e65 ]
Looking through old emails in my INBOX, I came across a patch from Luis
Henriques that attempted to fix a race of two stat tracers registering the
same stat trace (extremely unlikely, as this is done in the kernel, and
probably doesn't even exist). The submitted patch wasn't quite right as it
needed to deal with clean up a bit better (if two stat tracers were the
same, it would have the same files).
But to make the code cleaner, all we needed to do is to keep the
all_stat_sessions_mutex held for most of the registering function.
Link: http://lkml.kernel.org/r/1410299375-20068-1-git-send-email-luis.henriques@canonical.com
Fixes: 002bb86d8d ("tracing/ftrace: separate events tracing and stats tracing engine")
Reported-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afccc00f75 ]
tracing_stat_init() was always returning '0', even on the error paths. It
now returns -ENODEV if tracing_init_dentry() fails or -ENOMEM if it fails
to created the 'trace_stat' debugfs directory.
Link: http://lkml.kernel.org/r/1410299381-20108-1-git-send-email-luis.henriques@canonical.com
Fixes: ed6f1c996b ("tracing: Check return value of tracing_init_dentry()")
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
[ Pulled from the archeological digging of my INBOX ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 965c94f309 ]
An ioda_pe for each VF is allocated in pnv_pci_sriov_enable() before
the pci_dev for the VF is created. We need to set the pe->pdev pointer
at some point after the pci_dev is created. Currently we do that in:
pcibios_bus_add_device()
pnv_pci_dma_dev_setup() (via phb->ops.dma_dev_setup)
/* fixup is done here */
pnv_pci_ioda_dma_dev_setup() (via pnv_phb->dma_dev_setup)
The fixup needs to be done before setting up DMA for for the VF's PE,
but there's no real reason to delay it until this point. Move the
fixup into pnv_pci_ioda_fixup_iov() so the ordering is:
pcibios_add_device()
pnv_pci_ioda_fixup_iov() (via ppc_md.pcibios_fixup_sriov)
pcibios_bus_add_device()
...
This isn't strictly required, but it's a slightly more logical place
to do the fixup and it simplifies pnv_pci_dma_dev_setup().
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-4-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 953c4a08df ]
o call skb_reset_network_header() before hdlc->xmit()
o change skb proto to HDLC (0x0019) before hdlc->xmit()
o call dev_queue_xmit_nit() before hdlc->xmit()
This changes make it possible to trace (tcpdump) outgoing layer2
(ETH_P_HDLC) packets
Additionally call skb_reset_network_header() after each skb_push() /
skb_pull().
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b04817885 ]
There is duplicated argument to && in function fsl_qdma_free_chan_resources,
which looks like a typo, pointer fsl_queue->desc_pool also needs NULL check,
fix it.
Detected with coccinelle.
Fixes: b092529e0a ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Peng Ma <peng.ma@nxp.com>
Tested-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20200120125843.34398-1-chenzhou10@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15fb05fd28 ]
UDF 2.60 standard states in section 2.2.14.2:
A partition with Access Type 3 (rewritable) shall define a Freed
Space Bitmap or a Freed Space Table, see 2.3.3. All other partitions
shall not define a Freed Space Bitmap or a Freed Space Table.
Rewritable partitions are used on media that require some form of
preprocessing before re-writing data (for example legacy MO). Such
partitions shall use Access Type 3.
Overwritable partitions are used on media that do not require
preprocessing before overwriting data (for example: CD-RW, DVD-RW,
DVD+RW, DVD-RAM, BD-RE, HD DVD-Rewritable). Such partitions shall
use Access Type 4.
however older versions of the standard didn't have this wording and
there are tools out there that create UDF filesystems with rewritable
partitions but that don't contain a Freed Space Bitmap or a Freed Space
Table on media that does not require pre-processing before overwriting a
block. So instead of forcing media with rewritable partition read-only,
base this decision on presence of a Freed Space Bitmap or a Freed Space
Table.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Fixes: b085fbe2ef ("udf: Fix crash during mount")
Link: https://lore.kernel.org/linux-fsdevel/20200112144735.hj2emsoy4uwsouxz@pali
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4cf7aa57e ]
Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.
This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.
Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dacc909233 ]
When checking whether the reported lfb_size makes sense, the height
* stride result is page-aligned before seeing whether it exceeds the
reported size.
This doesn't work if height * stride is not an exact number of pages.
For example, as reported in the kernel bugzilla below, an 800x600x32 EFI
framebuffer gets skipped because of this.
Move the PAGE_ALIGN to after the check vs size.
Reported-by: Christopher Head <chead@chead.ca>
Tested-by: Christopher Head <chead@chead.ca>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206051
Link: https://lkml.kernel.org/r/20200107230410.2291947-1-nivedita@alum.mit.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e3002837 ]
The parent clk for gmac clk ctrl has to be gmac_main_clk (125MHz) instead
of dpll_gmac_ck (1GHz). This is caused incorrect CPSW MDIO operation.
Hence, fix it.
Fixes: dffa9051d5 ('clk: ti: dra7: add new clkctrl data')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e45330e3 ]
Without any form of coordination, any case where multiple allocations
from the same mempool are needed at a time to make forward progress can
deadlock under memory pressure.
This is the case for struct bio_post_read_ctx, as one can be allocated
to decrypt a Merkle tree page during fsverity_verify_bio(), which itself
is running from a post-read callback for a data bio which has its own
struct bio_post_read_ctx.
Fix this by freeing the first bio_post_read_ctx before calling
fsverity_verify_bio(). This works because verity (if enabled) is always
the last post-read step.
This deadlock can be reproduced by trying to read from an encrypted
verity file after reducing NUM_PREALLOC_POST_READ_CTXS to 1 and patching
mempool_alloc() to pretend that pool->alloc() always fails.
Note that since NUM_PREALLOC_POST_READ_CTXS is actually 128, to actually
hit this bug in practice would require reading from lots of encrypted
verity files at the same time. But it's theoretically possible, as N
available objects isn't enough to guarantee forward progress when > N/2
threads each need 2 objects at a time.
Fixes: 22cfe4b48c ("ext4: add fs-verity read support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20191231181222.47684-1-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a09decff5c ]
If the journal is dirty when the filesystem is mounted, jbd2 will replay
the journal but the journal superblock will not be updated by
journal_reset() because JBD2_ABORT flag is still set (it was set in
journal_init_common()). This is problematic because when a new transaction
is then committed, it will be recorded in block 1 (journal->j_tail was set
to 1 in journal_reset()). If unclean shutdown happens again before the
journal superblock is updated, the new recorded transaction will not be
replayed during the next mount (because of stale sb->s_start and
sb->s_sequence values) which can lead to filesystem corruption.
Fixes: 85e0c4e89c ("jbd2: if the journal is aborted then don't allow update of the log tail")
Signed-off-by: Kai Li <li.kai4@h3c.com>
Link: https://lore.kernel.org/r/20200111022542.5008-1-li.kai4@h3c.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b64a650f0 ]
It was observed[1] on arm64 that __builtin_strlen led to an infinite
loop in the get_size selftest. This is because __builtin_strlen (and
other builtins) may sometimes result in a call to the C library
function. The C library implementation of strlen uses an IFUNC
resolver to load the most efficient strlen implementation for the
underlying machine and hence has a PLT indirection even for static
binaries. Because this binary avoids the C library startup routines,
the PLT initialization never happens and hence the program gets stuck
in an infinite loop.
On x86_64 the __builtin_strlen just happens to expand inline and avoid
the call but that is not always guaranteed.
Further, while testing on x86_64 (Fedora 31), it was observed that the
test also failed with a segfault inside write() because the generated
code for the write function in glibc seems to access TLS before the
syscall (probably due to the cancellation point check) and fails
because TLS is not initialised.
To mitigate these problems, this patch reduces the interface with the
C library to just the syscall function. The syscall function still
sets errno on failure, which is undesirable but for now it only
affects cases where syscalls fail.
[1] https://bugs.linaro.org/show_bug.cgi?id=5479
Signed-off-by: Siddhesh Poyarekar <siddhesh@gotplt.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f8f76444b ]
[why]
Upon exiting a fixed active VRR state, the state isn't cleared. This
leads to the variable VRR range to be calculated incorrectly.
[how]
Set fixed active state to false when updating vrr params
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2052d032c0 ]
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f0898 ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c1ed62ae0 ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/usb/gadget/udc/core.c, 1175:
kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/core.c, 1195:
mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 212:
debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2114:
devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.
To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f42e4b337b ]
The sizeof is currently on args.src and args.dst and should be on
*args.src and *args.dst. Fortunately these sizes just so happen
to be the same size so it worked, however, this should be fixed
and it also cleans up static analysis warnings
Addresses-Coverity: ("sizeof not portable")
Fixes: f268307ec7 ("nouveau: simplify nouveau_dmem_migrate_vma")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc3a8b295e ]
Why it does not work at the moment:
- num_chipselect sets the number of cs-gpios that are in the DT.
This comes from drivers/spi/spi.c
- num_chipselect gets set with devm_spi_register_controller, that is
called in drivers/spi/spi.c
- devm_spi_register_controller got called after num_chipselect has
been used.
How this commit fixes the issue:
- devm_spi_register_controller gets called before num_chipselect is
being used.
Fixes: c7a4025995 ("spi: lpspi: use the core way to implement cs-gpio function")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20191204141312.1411251-1-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df5e984c8b ]
guest vm gets 0xffffffff when reading RCC_DEV0_EPF0_STRAP0,
as a consequence, the rev_id and external_rev_id are wrong.
workaround it by hardcoding the rev_id to 0, which is the default value.
v2. add comment in the code
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b74351287d ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
kernel/irq/manage.c, 523:
synchronize_irq in disable_irq
drivers/uio/uio_dmem_genirq.c, 140:
disable_irq in uio_dmem_genirq_irqcontrol
drivers/uio/uio_dmem_genirq.c, 134:
_raw_spin_lock_irqsave in uio_dmem_genirq_irqcontrol
synchronize_irq() can sleep at runtime.
To fix this bug, disable_irq() is called without holding the spinlock.
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218094405.6009-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b8651aac1 ]
The compilation error is redeclaration showed as following:
In file included from ../../../include/linux/limits.h:6,
from /usr/include/x86_64-linux-gnu/bits/local_lim.h:38,
from /usr/include/x86_64-linux-gnu/bits/posix1_lim.h:161,
from /usr/include/limits.h:183,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/limits.h:194,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/syslimits.h:7,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/limits.h:34,
from ../../../include/linux/raid/pq.h:30,
from algos.c:14:
../../../include/linux/types.h:114:15: error: conflicting types for ‘int64_t’
typedef s64 int64_t;
^~~~~~~
In file included from /usr/include/stdint.h:34,
from /usr/lib/gcc/x86_64-linux-gnu/8/include/stdint.h:9,
from /usr/include/inttypes.h:27,
from ../../../include/linux/raid/pq.h:29,
from algos.c:14:
/usr/include/x86_64-linux-gnu/bits/stdint-intn.h:27:19: note: previous \
declaration of ‘int64_t’ was here
typedef __int64_t int64_t;
Fixes: 54d50897d5 ("linux/kernel.h: split *_MAX and *_MIN macros into <linux/limits.h>")
Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
