hash_page() needs to read page tables from kernel memory. When entire
kernel memory is mapped by BATs, which is normally the case when
CONFIG_STRICT_KERNEL_RWX is not set, it works even if the page hosting
the page table is not referenced in the MMU hash table.
However, if the page where the page table resides is not covered by
a BAT, a DSI fault can be encountered from hash_page(), and it loops
forever. This can happen when CONFIG_STRICT_KERNEL_RWX is selected
and the alignment of the different regions is too small to allow
covering the entire memory with BATs. This also happens when
CONFIG_DEBUG_PAGEALLOC is selected or when booting with 'nobats'
flag.
Also, if the page containing the kernel stack is not present in the
MMU hash table, registers cannot be saved and a recursive DSI fault
is encountered.
To allow hash_page() to properly do its job at all time and load the
MMU hash table whenever needed, it must run with data MMU disabled.
This means it must be called before re-enabling data MMU. To allow
this, registers clobbered by hash_page() and create_hpte() have to
be saved in the thread struct together with SRR0, SSR1, DAR and DSISR.
It is also necessary to ensure that DSI prolog doesn't overwrite
regs saved by prolog of the current running exception. That means:
- DSI can only use SPRN_SPRG_SCRATCH0
- Exceptions must free SPRN_SPRG_SCRATCH0 before writing to the stack.
This also fixes the Oops reported by Erhard when create_hpte() is
called by add_hash_page().
Due to prolog size increase, a few more exceptions had to get split
in two parts.
Fixes: cd08f109e2 ("powerpc/32s: Enable CONFIG_VMAP_STACK")
Reported-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206501
Link: https://lore.kernel.org/r/64a4aa44686e9fd4b01333401367029771d9b231.1581761633.git.christophe.leroy@c-s.fr
Commit 55c8fc3f49 ("powerpc/8xx: reintroduce 16K pages with HW
assistance") redefined pte_t as a struct of 4 pte_basic_t, because
in 16K pages mode there are four identical entries in the
page table. But the size of hugepage tables is calculated based
of the size of (void *). Therefore, we end up with page tables
of size 1k instead of 4k for 512k pages.
As 512k hugepage tables are the same size as standard page tables,
ie 4k, use the standard page tables instead of PGT_CACHE tables.
Fixes: 3fb69c6a1a ("powerpc/8xx: Enable 512k hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/90ec56a2315be602494619ed0223bba3b0b8d619.1580997007.git.christophe.leroy@c-s.fr
- Implement user_access_begin() and friends for our platforms that support
controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure" virtual
machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit VDSO, and
some other improvements.
- A series to use the PCI hotplug framework to control opencapi card's so that
they can be reset and re-read after flashing a new FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to:
Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen Zhou, Christophe Leroy,
Frederic Barrat, Greg Kurz, Jason A. Donenfeld, Joel Stanley, Jordan Niethe,
Julia Lawall, Krzysztof Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus
Walleij, Michael Bringmann, Nathan Chancellor, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy
Dunlap, Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago Jung
Bauermann, Tyrel Datwyler, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=xpG+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
Patch series "Fixup page directory freeing", v4.
This is a repost of patch series from Peter with the arch specific changes
except ppc64 dropped. ppc64 changes are added here because we are redoing
the patch series on top of ppc64 changes. This makes it easy to backport
these changes. Only the first 2 patches need to be backported to stable.
The thing is, on anything SMP, freeing page directories should observe the
exact same order as normal page freeing:
1) unhook page/directory
2) TLB invalidate
3) free page/directory
Without this, any concurrent page-table walk could end up with a
Use-after-Free. This is esp. trivial for anything that has software
page-table walkers (HAVE_FAST_GUP / software TLB fill) or the hardware
caches partial page-walks (ie. caches page directories).
Even on UP this might give issues since mmu_gather is preemptible these
days. An interrupt or preempted task accessing user pages might stumble
into the free page if the hardware caches page directories.
This patch series fixes ppc64 and add generic MMU_GATHER changes to
support the conversion of other architectures. I haven't added patches
w.r.t other architecture because they are yet to be acked.
This patch (of 9):
A followup patch is going to make sure we correctly invalidate page walk
cache before we free page table pages. In order to keep things simple
enable RCU_TABLE_FREE even for !SMP so that we don't have to fixup the
!SMP case differently in the followup patch
!SMP case is right now broken for radix translation w.r.t page walk
cache flush. We can get interrupted in between page table free and
that would imply we have page walk cache entries pointing to tables
which got freed already. Michael said "both our platforms that run on
Power9 force SMP on in Kconfig, so the !SMP case is unlikely to be a
problem for anyone in practice, unless they've hacked their kernel to
build it !SMP."
Link: http://lkml.kernel.org/r/20200116064531.483522-2-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to provide a clearer, more symmetric API for pinning and
unpinning DMA pages. This way, pin_user_pages*() calls match up with
unpin_user_pages*() calls, and the API is a lot closer to being
self-explanatory.
Link: http://lkml.kernel.org/r/20200107224558.2362728-23-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Convert from get_user_pages() to pin_user_pages().
2. As required by pin_user_pages(), release these pages via
put_user_page().
Link: http://lkml.kernel.org/r/20200107224558.2362728-21-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On book3s/32 CPUs that are handling MMU through a hash table,
MMU_init_hw() function was adapted for VMAP_STACK in order to
handle virtual addresses instead of physical addresses in the
low level hash functions.
When using KASAN, the same adaptations are required for the
early hash table set up by kasan_early_hash_table() function.
Fixes: cd08f109e2 ("powerpc/32s: Enable CONFIG_VMAP_STACK")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/fc8390a33c2a470105f01abbcbdc7916c30c0a54.1580301269.git.christophe.leroy@c-s.fr
At the moment, bad_kuap_fault() reports a fault only if a bad access
to userspace occurred while access to userspace was not granted.
But if a fault occurs for a write outside the allowed userspace
segment(s) that have been unlocked, bad_kuap_fault() fails to
detect it and the kernel loops forever in do_page_fault().
Fix it by checking that the accessed address is within the allowed
range.
Fixes: a68c31fc01 ("powerpc/32s: Implement Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f48244e9485ada0a304ed33ccbb8da271180c80d.1579866752.git.christophe.leroy@c-s.fr
Add support of KASAN_VMALLOC on PPC32.
To allow this, the early shadow covering the VMALLOC space
need to be removed once high_memory var is set and before
freeing memblock.
And the VMALLOC area need to be aligned such that boundaries
are covered by a full shadow page.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/031dec5487bde9b2181c8b3c9800e1879cf98c1a.1579024426.git.christophe.leroy@c-s.fr
Running vdsotest leaves many times the following log:
[ 79.629901] vdsotest[396]: User access of kernel address (ffffffff) - exploit attempt? (uid: 0)
A pointer set to (-1) is likely a programming error similar to
a NULL pointer and is not worth logging as an exploit attempt.
Don't log user accesses to 0xffffffff.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0728849e826ba16f1fbd6fa7f5c6cc87bd64e097.1577087627.git.christophe.leroy@c-s.fr
A few changes to retrieve DAR and DSISR from struct regs
instead of retrieving them directly, as they may have
changed due to a TLB miss.
Also modifies hash_page() and friends to work with virtual
data addresses instead of physical ones. Same on load_up_fpu()
and load_up_altivec().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fix tovirt_vmstack call in head_32.S to fix CHRP build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2e2509a242fd5f3e23df4a06530c18060c4d321e.1576916812.git.christophe.leroy@c-s.fr
Commit a25bd72bad ("powerpc/mm/radix: Workaround prefetch issue with
KVM") introduced a number of workarounds as coming out of a guest with
the mmu enabled would make the cpu would start running in hypervisor
state with the PID value from the guest. The cpu will then start
prefetching for the hypervisor with that PID value.
In Power9 DD2.2 the cpu behaviour was modified to fix this. When
accessing Quadrant 0 in hypervisor mode with LPID != 0 prefetching will
not be performed. This means that we can get rid of the workarounds for
Power9 DD2.2 and later revisions. Add a new cpu feature
CPU_FTR_P9_RADIX_PREFETCH_BUG to indicate if the workarounds are needed.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191206031722.25781-1-jniethe5@gmail.com
Verification cannot rely on simple bit checking because on some
platforms PAGE_RW is 0, checking that a page is not W means
checking that PAGE_RO is set instead of checking that PAGE_RW
is not set.
Use pte helpers instead of checking bits.
Fixes: 453d87f6a8 ("powerpc/mm: Warn if W+X pages found on boot")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0d894839fdbb19070f0e1e4140363be4f2bb62fc.1578989540.git.christophe.leroy@c-s.fr
Selecting CONFIG_PPC_DEBUG_WX only impacts ptdump and pgtable_32/64
init calls. Declaring related functions in asm/pgtable.h implies
rebuilding almost everything.
Move ptdump_check_wx() declaration in mm/mmu_decl.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bf34fd9dca61eadf9a134a9f89ebbc162cfd5f86.1578986011.git.christophe.leroy@c-s.fr
With STRICT_KERNEL_RWX on in a relocatable kernel under the hash MMU,
if the position the kernel is loaded at is not 16M aligned things go
horribly wrong. Specifically hash__mark_initmem_nx() will call
hash__change_memory_range() which then aligns down the start address,
and due to the text not being 16M aligned causes some of the kernel
text to be marked non-executable.
We can avoid this when selecting the linear mapping size, so do so and
print a warning. I tested this for various alignments and as long as
the position is 64K aligned it's fine (the base requirement for
powerpc).
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Add details of the failure mode]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191224064126.183670-1-ruscur@russell.cc
We currently try to shrink a single zone when removing memory. We use
the zone of the first page of the memory we are removing. If that
memmap was never initialized (e.g., memory was never onlined), we will
read garbage and can trigger kernel BUGs (due to a stale pointer):
BUG: unable to handle page fault for address: 000000000000353d
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 1 PID: 7 Comm: kworker/u8:0 Not tainted 5.3.0-rc5-next-20190820+ #317
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.4
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
RIP: 0010:clear_zone_contiguous+0x5/0x10
Code: 48 89 c6 48 89 c3 e8 2a fe ff ff 48 85 c0 75 cf 5b 5d c3 c6 85 fd 05 00 00 01 5b 5d c3 0f 1f 840
RSP: 0018:ffffad2400043c98 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000200000000 RCX: 0000000000000000
RDX: 0000000000200000 RSI: 0000000000140000 RDI: 0000000000002f40
RBP: 0000000140000000 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000140000
R13: 0000000000140000 R14: 0000000000002f40 R15: ffff9e3e7aff3680
FS: 0000000000000000(0000) GS:ffff9e3e7bb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000353d CR3: 0000000058610000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__remove_pages+0x4b/0x640
arch_remove_memory+0x63/0x8d
try_remove_memory+0xdb/0x130
__remove_memory+0xa/0x11
acpi_memory_device_remove+0x70/0x100
acpi_bus_trim+0x55/0x90
acpi_device_hotplug+0x227/0x3a0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x221/0x550
worker_thread+0x50/0x3b0
kthread+0x105/0x140
ret_from_fork+0x3a/0x50
Modules linked in:
CR2: 000000000000353d
Instead, shrink the zones when offlining memory or when onlining failed.
Introduce and use remove_pfn_range_from_zone(() for that. We now
properly shrink the zones, even if we have DIMMs whereby
- Some memory blocks fall into no zone (never onlined)
- Some memory blocks fall into multiple zones (offlined+re-onlined)
- Multiple memory blocks that fall into different zones
Drop the zone parameter (with a potential dubious value) from
__remove_pages() and __remove_section().
Link: http://lkml.kernel.org/r/20191006085646.5768-6-david@redhat.com
Fixes: f1dd2cd13c ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b]
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: <stable@vger.kernel.org> [5.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These slice routines are called from the SLB miss handler, which can
lead to warnings from the IRQ code, because we have not reconciled the
IRQ state properly:
WARNING: CPU: 72 PID: 30150 at arch/powerpc/kernel/irq.c:258 arch_local_irq_restore.part.0+0xcc/0x100
Modules linked in:
CPU: 72 PID: 30150 Comm: ftracetest Not tainted 5.5.0-rc2-gcc9x-g7e0165b2f1a9 #1
NIP: c00000000001d83c LR: c00000000029ab90 CTR: c00000000026cf90
REGS: c0000007eee3b960 TRAP: 0700 Not tainted (5.5.0-rc2-gcc9x-g7e0165b2f1a9)
MSR: 8000000000021033 <SF,ME,IR,DR,RI,LE> CR: 22242844 XER: 20000000
CFAR: c00000000001d780 IRQMASK: 0
...
NIP arch_local_irq_restore.part.0+0xcc/0x100
LR trace_graph_entry+0x270/0x340
Call Trace:
trace_graph_entry+0x254/0x340 (unreliable)
function_graph_enter+0xe4/0x1a0
prepare_ftrace_return+0xa0/0x130
ftrace_graph_caller+0x44/0x94 # (get_slice_psize())
slb_allocate_user+0x7c/0x100
do_slb_fault+0xf8/0x300
instruction_access_slb_common+0x140/0x180
Fixes: 48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191221121337.4894-1-mpe@ellerman.id.au
Remove __init qualifier for mmu_mapin_ram_chunk() as it is called by
mmu_mark_initmem_nx() and mmu_mark_rodata_ro() which are not __init
functions.
At the same time, mark it static as it is only used in this file.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: a2227a2777 ("powerpc/32: Don't populate page tables for block mapped pages except on the 8xx")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/56648921986a6b3e7315b1fbbf4684f21bd2dea8.1576310997.git.christophe.leroy@c-s.fr
Some powerpc platforms (e.g. 85xx) limit DMA-able memory way below 4G.
If a system has more physical memory than this limit, the swiotlb
buffer is not addressable because it is allocated from memblock using
top-down mode.
Force memblock to bottom-up mode before calling swiotlb_init() to
ensure that the swiotlb buffer is DMA-able.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191204123524.22919-1-rppt@kernel.org
Merge updates from Andrew Morton:
"Incoming:
- a small number of updates to scripts/, ocfs2 and fs/buffer.c
- most of MM
I still have quite a lot of material (mostly not MM) staged after
linux-next due to -next dependencies. I'll send those across next week
as the preprequisites get merged up"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm/page_io.c: annotate refault stalls from swap_readpage
mm/Kconfig: fix trivial help text punctuation
mm/Kconfig: fix indentation
mm/memory_hotplug.c: remove __online_page_set_limits()
mm: fix typos in comments when calling __SetPageUptodate()
mm: fix struct member name in function comments
mm/shmem.c: cast the type of unmap_start to u64
mm: shmem: use proper gfp flags for shmem_writepage()
mm/shmem.c: make array 'values' static const, makes object smaller
userfaultfd: require CAP_SYS_PTRACE for UFFD_FEATURE_EVENT_FORK
fs/userfaultfd.c: wp: clear VM_UFFD_MISSING or VM_UFFD_WP during userfaultfd_register()
userfaultfd: wrap the common dst_vma check into an inlined function
userfaultfd: remove unnecessary WARN_ON() in __mcopy_atomic_hugetlb()
userfaultfd: use vma_pagesize for all huge page size calculation
mm/madvise.c: use PAGE_ALIGN[ED] for range checking
mm/madvise.c: replace with page_size() in madvise_inject_error()
mm/mmap.c: make vma_merge() comment more easy to understand
mm/hwpoison-inject: use DEFINE_DEBUGFS_ATTRIBUTE to define debugfs fops
autonuma: reduce cache footprint when scanning page tables
autonuma: fix watermark checking in migrate_balanced_pgdat()
...
Patch series "hugetlbfs: convert macros to static inline, fix sparse
warning".
The definition for huge_pte_offset() in <linux/hugetlb.h> causes a
sparse warning in the !CONFIG_HUGETLB_PAGE. Fix this as well as
converting all macros in this block of definitions to static inlines for
better type checking.
When making the above changes, build errors were found in powerpc due to
duplicate definitions. A separate powerpc specific patch is included as
a requisite to remove the definitions and get them from
<linux/hugetlb.h>.
This patch (of 2):
This removes the power specific stubs created by commit aad71e3928
("powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n") used when
!CONFIG_HUGETLB_PAGE. Instead, it addresses the build break by getting
the definitions from <linux/hugetlb.h>. This allows the macros in
<linux/hugetlb.h> to be replaced with static inlines.
Link: http://lkml.kernel.org/r/20191112194558.139389-2-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights:
- Infrastructure for secure boot on some bare metal Power9 machines. The
firmware support is still in development, so the code here won't actually
activate secure boot on any existing systems.
- A change to xmon (our crash handler / pseudo-debugger) to restrict it to
read-only mode when the kernel is lockdown'ed, otherwise it's trivial to drop
into xmon and modify kernel data, such as the lockdown state.
- Support for KASLR on 32-bit BookE machines (Freescale / NXP).
- Fixes for our flush_icache_range() and __kernel_sync_dicache() (VDSO) to work
with memory ranges >4GB.
- Some reworks of the pseries CMM (Cooperative Memory Management) driver to
make it behave more like other balloon drivers and enable some cleanups of
generic mm code.
- A series of fixes to our hardware breakpoint support to properly handle
unaligned watchpoint addresses.
Plus a bunch of other smaller improvements, fixes and cleanups.
Thanks to:
Alastair D'Silva, Andrew Donnellan, Aneesh Kumar K.V, Anthony Steinhauser,
Cédric Le Goater, Chris Packham, Chris Smart, Christophe Leroy, Christopher M.
Riedl, Christoph Hellwig, Claudio Carvalho, Daniel Axtens, David Hildenbrand,
Deb McLemore, Diana Craciun, Eric Richter, Geert Uytterhoeven, Greg
Kroah-Hartman, Greg Kurz, Gustavo L. F. Walbon, Hari Bathini, Harish, Jason
Yan, Krzysztof Kozlowski, Leonardo Bras, Mathieu Malaterre, Mauro S. M.
Rodrigues, Michal Suchanek, Mimi Zohar, Nathan Chancellor, Nathan Lynch, Nayna
Jain, Nick Desaulniers, Oliver O'Halloran, Qian Cai, Rasmus Villemoes, Ravi
Bangoria, Sam Bobroff, Santosh Sivaraj, Scott Wood, Thomas Huth, Tyrel
Datwyler, Vaibhav Jain, Valentin Longchamp, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=JHzg
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Infrastructure for secure boot on some bare metal Power9 machines.
The firmware support is still in development, so the code here
won't actually activate secure boot on any existing systems.
- A change to xmon (our crash handler / pseudo-debugger) to restrict
it to read-only mode when the kernel is lockdown'ed, otherwise it's
trivial to drop into xmon and modify kernel data, such as the
lockdown state.
- Support for KASLR on 32-bit BookE machines (Freescale / NXP).
- Fixes for our flush_icache_range() and __kernel_sync_dicache()
(VDSO) to work with memory ranges >4GB.
- Some reworks of the pseries CMM (Cooperative Memory Management)
driver to make it behave more like other balloon drivers and enable
some cleanups of generic mm code.
- A series of fixes to our hardware breakpoint support to properly
handle unaligned watchpoint addresses.
Plus a bunch of other smaller improvements, fixes and cleanups.
Thanks to: Alastair D'Silva, Andrew Donnellan, Aneesh Kumar K.V,
Anthony Steinhauser, Cédric Le Goater, Chris Packham, Chris Smart,
Christophe Leroy, Christopher M. Riedl, Christoph Hellwig, Claudio
Carvalho, Daniel Axtens, David Hildenbrand, Deb McLemore, Diana
Craciun, Eric Richter, Geert Uytterhoeven, Greg Kroah-Hartman, Greg
Kurz, Gustavo L. F. Walbon, Hari Bathini, Harish, Jason Yan, Krzysztof
Kozlowski, Leonardo Bras, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michal Suchanek, Mimi Zohar, Nathan Chancellor, Nathan Lynch, Nayna
Jain, Nick Desaulniers, Oliver O'Halloran, Qian Cai, Rasmus Villemoes,
Ravi Bangoria, Sam Bobroff, Santosh Sivaraj, Scott Wood, Thomas Huth,
Tyrel Datwyler, Vaibhav Jain, Valentin Longchamp, YueHaibing"
* tag 'powerpc-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (144 commits)
powerpc/fixmap: fix crash with HIGHMEM
x86/efi: remove unused variables
powerpc: Define arch_is_kernel_initmem_freed() for lockdep
powerpc/prom_init: Use -ffreestanding to avoid a reference to bcmp
powerpc: Avoid clang warnings around setjmp and longjmp
powerpc: Don't add -mabi= flags when building with Clang
powerpc: Fix Kconfig indentation
powerpc/fixmap: don't clear fixmap area in paging_init()
selftests/powerpc: spectre_v2 test must be built 64-bit
powerpc/powernv: Disable native PCIe port management
powerpc/kexec: Move kexec files into a dedicated subdir.
powerpc/32: Split kexec low level code out of misc_32.S
powerpc/sysdev: drop simple gpio
powerpc/83xx: map IMMR with a BAT.
powerpc/32s: automatically allocate BAT in setbat()
powerpc/ioremap: warn on early use of ioremap()
powerpc: Add support for GENERIC_EARLY_IOREMAP
powerpc/fixmap: Use __fix_to_virt() instead of fix_to_virt()
powerpc/8xx: use the fixmapped IMMR in cpm_reset()
powerpc/8xx: add __init to cpm1 init functions
...
These are pure cache maintainance routines, so drop the unused
struct device argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit d2f15e0979 ("powerpc/32: always populate page tables for
Abatron BDI.") wrongly sets page tables for any PPC32 for using BDI,
and does't update them after init (remove RX on init section, set
text and rodata read-only)
Only the 8xx requires page tables to be populated for using the BDI.
They also need to be populated in order to see the mappings in
/sys/kernel/debug/kernel_page_tables
On BOOK3S_32, pages that are not mapped by page tables are mapped
by BATs. The BDI knows BATs and they can be viewed in
/sys/kernel/debug/powerpc/block_address_translation
Only set pagetables for RAM and IMMR on the 8xx and properly update
them at the end of init.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c8610942203e0d93fcb02ad20c57edd3adb4c9d3.1566554029.git.christophe.leroy@c-s.fr
One may want to disable kaslr when boot, so provide a cmdline parameter
'nokaslr' to support this.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The original kernel still exists in the memory, clear it now.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After we have the basic support of relocate the kernel in some
appropriate place, we can start to randomize the offset now.
Entropy is derived from the banner and timer, which will change every
build and boot. This not so much safe so additionally the bootloader may
pass entropy via the /chosen/kaslr-seed node in device tree.
We will use the first 512M of the low memory to randomize the kernel
image. The memory will be split in 64M zones. We will use the lower 8
bit of the entropy to decide the index of the 64M zone. Then we chose a
16K aligned offset inside the 64M zone to put the kernel in.
We also check if we will overlap with some areas like the dtb area, the
initrd area or the crashkernel area. If we cannot find a proper area,
kaslr will be disabled and boot from the original kernel.
Some pieces of code are derived from arch/x86/boot/compressed/kaslr.c or
arch/arm64/kernel/kaslr.c such as rotate_xor(). Credit goes to Kees and
Ard.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch add support to boot kernel from places other than KERNELBASE.
Since CONFIG_RELOCATABLE has already supported, what we need to do is
map or copy kernel to a proper place and relocate. Freescale Book-E
parts expect lowmem to be mapped by fixed TLB entries(TLB1). The TLB1
entries are not suitable to map the kernel directly in a randomized
region, so we chose to copy the kernel to a proper place and restart to
relocate.
The offset of the kernel was not randomized yet(a fixed 64M is set). We
will randomize it in the next patch.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
[mpe: Use PTRRELOC() in early_init()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a new helper reloc_kernel_entry() to jump back to the start of the
new kernel. After we put the new kernel in a randomized place we can use
this new helper to enter the kernel and begin to relocate again.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a new helper create_kaslr_tlb_entry() to create a tlb entry by the
virtual and physical address. This is a preparation to support boot kernel
at a randomized address.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now the kernel base is a fixed value - KERNELBASE. To support KASLR, we
need a variable to store the kernel base.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These two variables are both defined in init_32.c and init_64.c. Move
them to init-common.c and make them __ro_after_init.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Tested-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This operation takes a significant amount of time when hotplugging
large amounts of memory (~50 seconds with 890GB of persistent memory).
This was orignally in commit fb5924fddf
("powerpc/mm: Flush cache on memory hot(un)plug") to support memtrace,
but the flush on add is not needed as it is flushed on remove.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-7-alastair@au1.ibm.com
When presented with large amounts of memory being hotplugged
(in my test case, ~890GB), the call to flush_dcache_range takes
a while (~50 seconds), triggering RCU stalls.
This patch breaks up the call into 1GB chunks, calling
cond_resched() inbetween to allow the scheduler to run.
Fixes: fb5924fddf ("powerpc/mm: Flush cache on memory hot(un)plug")
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-6-alastair@au1.ibm.com
