Previous init path was based on old specs from old driver. Update it
as much as possible leaving some TODOs for not implemented functions.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move table init to tables_nphy.c, detect newer PHY which use different init.
We don't init newer PHYs yet but this at least shows what more is needed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following line shows my BCM4328 detected on SSB. We didn't include 0x0C rev.
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0C, vendor 0x4243)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/488636
Enhances module information with the names of the firmware files
that could be used by this driver. This helps tools like Jockey to
correctly detect and/or install the firmware files relevant to
this driver.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If userencounter the "Fatal DMA Problem" with a BCM43XX device, and
still wish to use b43 as the driver, their only option is to rebuild
the kernel with CONFIG_B43_FORCE_PIO. This patch removes this option and
allows PIO mode to be selected with a load-time parameter for the module.
Note that the configuration variable CONFIG_B43_PIO is also removed.
Once the DMA problem with the BCM4312 devices is solved, this patch will
likely be reverted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As shown in Kernel Bugzilla #14761, doing a controller restart after a
fatal DMA error does not accomplish anything other than consume the CPU
on an affected system. Accordingly, substitute a meaningful message for
the restart.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My gcc appears to be able to see past the function
boundary and notices that the variable 'behaviour'
could be used uninitialised:
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_register’:
drivers/net/wireless/b43/leds.c:339: warning: ‘behaviour’ may be used uninitialized in this function
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_init’:
drivers/net/wireless/b43/leds.c:262: warning: ‘behaviour’ may be used uninitialized in this function
because b43_led_get_sprominfo() didn't initialise
it in all cases.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The routine b43_is_hw_radio_enabled() has long been a problem.
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43_status()
returns a value of 2 (B43_STAT_STARTED) (BUG 14181). Fixing that
results in Bug 14538 in which the driver is unable to reassociate
after resuming from hibernation because b43_status() returns 0.
The correct fix would be to determine why the status is 0; however,
I have not yet found why that happens. The correct value is found for
my device, which has PHY revision >= 3.
Returning TRUE when the PHY revision < 3 and b43_status() returns 0 fixes
the regression for 2.6.32.
This patch fixes the problem in Red Hat Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_request_window() only needs a pointer to struct pcmcia_device, not
a pointer to a pointer.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
Acked-by: Karsten Keil <keil@b1-systems.de> (for ISDN)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This rewrites the error handling policies in the TX status handler.
It tries to be error-tolerant as in "try hard to not crash the machine".
It won't recover from errors (that are bugs in the firmware or driver),
because that's impossible. However, it will return a more or less useful
error message and bail out. It also tries hard to use rate-limited messages
to not flood the syslog in case of a failure.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
cxgb3: fix premature page unmap
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
vlan: Fix register_vlan_dev() error path
gro: Fix illegal merging of trailer trash
sungem: Fix Serdes detection.
net: fix mdio section mismatch warning
ppp: fix BUG on non-linear SKB (multilink receive)
ixgbe: Fixing EEH handler to handle more than one error
net: Fix the rollback test in dev_change_name()
Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
TI Davinci EMAC : Fix Console Hang when bringing the interface down
smsc911x: Fix Console Hang when bringing the interface down.
mISDN: fix error return in HFCmulti_init()
forcedeth: mac address fix
r6040: fix version printing
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
Bluetooth: Set general bonding security for ACL by default
r8169: Fix receive buffer length when MTU is between 1515 and 1536
can: add the missing netlink get_xstats_size callback
...
Enforce all device constraints on the descriptor memory region.
There are several constraints on the descriptor memory, as documented
in the specification. The current code does not enforce them and/or
incorrectly enforces them.
Those constraints are:
- The address limitations on 30/32bit engines, that also apply to
the skbs.
- The 4k alignment requirement on 30/32bit engines.
- The 8k alignment requirement on 64bit engines.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the RX error path for rev>=8 devices.
The wrong register size and definitions were used.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not mess with the original skb, but allocate an independent bouncebuffer.
This protects against bad interference with mac80211's assumptions about
the skb (which already caused bugs).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few PCMCIA network drivers can make use of values provided by the pcmcia
core, instead of tedious, independent CIS parsing.
xirc32ps_cs.c: manf_id
hostap_cs.c: multifunction count
b43/pcmcia.c: ConfigBase address and "Present"
smc91c92_cs.c: By default, mhz_setup() can use VERS_1 as it is stored
in struct pcmcia_device. Only some cards require workarounds, such as
reading out VERS_1 twice.
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
With the deprecation of the qual member of ieee80211_rx_status, that
calculation and an associated constant can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the WLAN_PRE80211 drivers moved to drivers/staging, this
distinction becomes unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While there may be a case for a driver adding its
own bits of radiotap information, none currently
does. Also, drivers would have to copy the code
to generate the radiotap bits that now mac80211
generates. If some driver in the future needs to
add some driver-specific information I'd expect
that to be in a radiotap vendor namespace and we
can add a different way of passing such data up
and having mac80211 include it.
Additionally, rename IEEE80211_CONF_RADIOTAP to
IEEE80211_CONF_MONITOR since it's still used by
b43(legacy) to obtain per-frame timestamps.
The purpose of this patch is to simplify the RX
code in mac80211 to make it easier to add paged
skb support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the following calibration functions:
-Set TX IQCC
-Set TX Power by Index
-PR41573 workaround (incomplete, needs PHY reset)
-Calc RX IQ Comp
-PHY Cordic
-Run Samples
-Start/Stop TX Tone
-part of PAPD Cal TX Power
-RX I/Q Calibration
-The basic structure of the periodic calibration wrapper
Software RFKILL (required by calibration) is also implemented in
this round.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43 allocates a bouncebuffer, if the supplied TX skb is in an invalid
memory range for DMA.
However, this is broken in that it fails to copy over some metadata to the
new skb.
This patch fixes three problems:
* Failure to adjust the ieee80211_tx_info pointer to the new buffer.
This results in a kmemcheck warning.
* Failure to copy the skb cb, which contains ieee80211_tx_info, to the new skb.
This results in breakage of various TX-status postprocessing (Rate control).
* Failure to transfer the queue mapping.
This results in the wrong queue being stopped on saturation and can result in queue overflow.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
net: Fix 'Re: PACKET_TX_RING: packet size is too long'
netdev: usb: dm9601.c can drive a device not supported yet, add support for it
qlge: Fix firmware mailbox command timeout.
qlge: Fix EEH handling.
AF_RAW: Augment raw_send_hdrinc to expand skb to fit iphdr->ihl (v2)
bonding: fix a race condition in calls to slave MII ioctls
virtio-net: fix data corruption with OOM
sfc: Set ip_summed correctly for page buffers passed to GRO
cnic: Fix L2CTX_STATUSB_NUM offset in context memory.
MAINTAINERS: rt2x00 list is moderated
airo: Reorder tests, check bounds before element
mac80211: fix for incorrect sequence number on hostapd injected frames
libertas spi: fix sparse errors
mac80211: trivial: fix spelling in mesh_hwmp
cfg80211: sme: deauthenticate on assoc failure
mac80211: keep auth state when assoc fails
mac80211: fix ibss joining
b43: add 'struct b43_wl' missing declaration
b43: Fix Bugzilla #14181 and the bug from the previous 'fix'
rt2x00: Fix crypto in TX frame for rt2800usb
...
We must check the bustype before using the host_pci pointer.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'struct b43_wl' declaration is missing at 'leds.h'.
It should be declared to avoid getting some GCC warnings at 'b43_leds_unregister'.
Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"b43: Fix PPC crash in rfkill polling on unload" fixed the bug reported
in Bugzilla No. 14181; however, it introduced a new bug. Whenever the
radio switch was turned off, it was necessary to unload and reload
the driver for it to recognize the switch again.
This patch fixes both the original bug in #14181 and the bug introduced by
the previous patch. It must be stated, however, that if there is a BCM4306/3
with an rfkill switch (not yet proven), then the driver will need an
unload/reload cycle to turn the device back on.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki