[ Upstream commit 0c3b532ad3 ]
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5c54a9d3 ]
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61 ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530b1dbd97 ]
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0f (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84aef4ed59 ]
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 805c74eac8 upstream.
Spurious wakeups are reported on the GPD G1619-04 which
can be absolved by programming the GPIO to ignore wakeups.
Cc: stable@vger.kernel.org
Reported-and-tested-by: George Melikov <mail@gmelikov.ru>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95dd1e34ff ]
If gpio_set_transitory() fails, we should free the GPIO again. Most
notably, the flag FLAG_REQUESTED has previously been set in
gpiod_request_commit(), and should be reset on failure.
To my knowledge, this does not affect any current users, since the
gpio_set_transitory() mainly returns 0 and -ENOTSUPP, which is converted
to 0. However the gpio_set_transitory() function calles the .set_config()
function of the corresponding GPIO chip and there are some GPIO drivers in
which some (unlikely) branches return other values like -EPROBE_DEFER,
and -EINVAL. In these cases, the above mentioned FLAG_REQUESTED would not
be reset, which results in the pin being blocked until the next reboot.
Fixes: e10f72bf4b ("gpio: gpiolib: Generalise state persistence beyond sleep")
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fc363413ef upstream.
We found a glitch when configuring the pad as output high. To avoid this
glitch, move the data value setting before direction config in the
function vf610_gpio_direction_output().
Fixes: 659d8a6231 ("gpio: vf610: add imx7ulp support")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
[Bartosz: tweak the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e8bc2dda5 ]
As timbgpio_irq_enable()/timbgpio_irq_disable() callback could be
executed under irq context, it could introduce double locks on
&tgpio->lock if it preempts other execution units requiring
the same locks.
timbgpio_gpio_set()
--> timbgpio_update_bit()
--> spin_lock(&tgpio->lock)
<interrupt>
--> timbgpio_irq_disable()
--> spin_lock_irqsave(&tgpio->lock)
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_irqsave()
on &tgpio->lock inside timbgpio_gpio_set() to prevent the possible
deadlock scenario.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f057511650 upstream.
Similarly to PXA3xx and MMP2, pinctrl-single isn't capable of setting
pin direction on MMP either.
Fixes: a770d94637 ("gpio: pxa: add pin control gpio direction and request")
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9315f17bf upstream.
pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.
Fixes: 5ae4cb94b3 ("gpio: aspeed: Add debounce support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26d9e5640d ]
The drivers uses a mutex and I2C bus access in its PMIC EIC chip
get implementation. This means these functions can sleep and the PMIC EIC
chip should set the can_sleep property to true.
This will ensure that a warning is printed when trying to get the
value from a context that potentially can't sleep.
Fixes: 348f3cde84 ("gpio: Add Spreadtrum PMIC EIC driver support")
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b547b5e52a ]
If an error occurs after a successful irq_domain_add_linear() call, it
should be undone by a corresponding irq_domain_remove(), as already done
in the remove function.
Fixes: c6ce2b6bff ("gpio: add TB10x GPIO driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7adc6c10 ]
Make tps68470_gpio_output() call tps68470_gpio_set() for output-only pins
too, so that the initial value passed to gpiod_direction_output() is
honored for these pins too.
Fixes: 275b13a655 ("gpio: Add support for TPS68470 GPIOs")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c00914e54 ]
In case of gpio-regmap, IRQ chip is added by regmap-irq and associated with
GPIO chip by gpiochip_irqchip_add_domain(). The initialization flag was not
added in gpiochip_irqchip_add_domain(), causing gpiochip_to_irq() to return
-EPROBE_DEFER.
Fixes: 5467801f1f ("gpio: Restrict usage of GPIO chip irq members before initialization")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfe6807d82 ]
The core gpiolib code is able to deal with multiple interrupt parents
for a single gpio irqchip. It however only allows a single piece
of data to be conveyed to all flow handlers (either the gpio_chip
or some other, driver-specific data).
This means that drivers have to go through some interesting dance
to find the correct context, something that isn't great in interrupt
context (see aebdc8abc9 for a prime
example).
Instead, offer an optional way for a pinctrl/gpio driver to provide
an array of pointers which gets used to provide the correct context
to the flow handler.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211026175815.52703-2-joey.gouly@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: 8c00914e54 ("gpiolib: Fix GPIO chip IRQ initialization restriction")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0a1bb16e0f upstream.
This driver's debugfs files have had a read operation since commit
2a9e27408e ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Cc: stable@kernel.org # v5.1+
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b75c47036 ]
Add the IRQCHIP_SKIP_SET_WAKE flag since there are no special IRQ Wake
bits that can be set to enable wakeup IRQ.
Fixes: 3d9edf09d4 ("[ARM] 4457/2: davinci: GPIO support")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49765b5f4 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ebe363197e ("gpio: add a reusable generic gpio_chip using regmap")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michael Walle <michael@walle.cc>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: linux-gpio@vger.kernel.org
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f8ecb7f85 ]
Current GPIO label is fixed, so can't distinguish different GPIO
controllers through labels. Use dev name instead.
Fixes: 7f2691a196 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e88a0feeb ]
Always configure GPIO pins which are used as interrupt source as INPUTs.
In case the default pin configuration is OUTPUT, or the prior stage does
configure the pins as OUTPUT, then Linux will not reconfigure the pin as
INPUT and no interrupts are received.
Always configure the interrupt source GPIO pin as input to fix the above case.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 07bd1a6cc7 ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 694175cd8a ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 96868dce64 ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 533aae7c94 ]
There are several places where we can crash the kernel by requesting
lines, unbinding the GPIO device, then calling any of the system calls
relevant to the GPIO character device's annonymous file descriptors:
ioctl(), read(), poll().
While I observed it with the GPIO simulator, it will also happen for any
of the GPIO devices that can be hot-unplugged - for instance any HID GPIO
expander (e.g. CP2112).
This affects both v1 and v2 uAPI.
This fixes it partially by checking if gdev->chip is not NULL but it
doesn't entirely remedy the situation as we still have a race condition
in which another thread can remove the device after the check.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d981 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cef8b5019 ]
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it. In case of IOCTLs use
switch-case pattern that seems the usual in such cases.
While at it, clarify necessity of else in gpiod_direction_output()
by attaching else if to the closing curly brace on a previous line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Stable-dep-of: 533aae7c94 ("gpiolib: cdev: fix NULL-pointer dereferences")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fecdb9f6 ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: f942a7de04 ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69bef19d6b upstream.
When running gpio test on nxp-ls1028 platform with below command
gpiomon --num-events=3 --rising-edge gpiochip1 25
There will be a warning trace as below:
Call trace:
free_irq+0x204/0x360
lineevent_free+0x64/0x70
gpio_ioctl+0x598/0x6a0
__arm64_sys_ioctl+0xb4/0x100
invoke_syscall+0x5c/0x130
......
el0t_64_sync+0x1a0/0x1a4
The reason of this issue is that calling request_threaded_irq()
function failed, and then lineevent_free() is invoked to release
the resource. Since the lineevent_state::irq was already set, so
the subsequent invocation of free_irq() would trigger the above
warning call trace. To fix this issue, set the lineevent_state::irq
after the IRQ register successfully.
Fixes: 4682427241 ("gpiolib: cdev: refactor lineevent cleanup into lineevent_free")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7df41a6f7 upstream.
We now remove the device's debugfs entries when unbinding the driver.
This now causes a NULL-pointer dereference on module exit because the
platform devices are unregistered *after* the global debugfs directory
has been recursively removed. Fix it by unregistering the devices first.
Fixes: 303e6da994 ("gpio: mockup: remove gpio debugfs when remove device")
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 279c12df8d ]
Commit e39d5ef678 ("powerpc/5xxx: extend mpc8xxx_gpio driver to support
mpc512x gpios") implemented support for IRQ_TYPE_LEVEL_LOW flow type in
mpc512x via falling edge type. Do same for mpc85xx which support was added
in commit 345e5c8a1c ("powerpc: Add interrupt support to mpc8xxx_gpio").
Fixes probing of lm90 hwmon driver on mpc85xx based board which use level
interrupt. Without it kernel prints error and refuse lm90 to work:
[ 15.258370] genirq: Setting trigger mode 8 for irq 49 failed (mpc8xxx_irq_set_type+0x0/0xf8)
[ 15.267168] lm90 0-004c: cannot request IRQ 49
[ 15.272708] lm90: probe of 0-004c failed with error -22
Fixes: 345e5c8a1c ("powerpc: Add interrupt support to mpc8xxx_gpio")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 303e6da994 ]
GPIO mockup debugfs is created in gpio_mockup_probe() but
forgot to remove when remove device. This patch add a devm
managed callback for removing them.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 518e26f11a ]
The regcache sync will set the cache_bypass = true, at that
time, when there is regmap write operation, it will bypass
the regmap cache, then the regcache sync will write back the
value from cache to register, which is not as our expectation.
Though regmap already use its internal lock to avoid such issue,
but this driver force disable the regmap internal lock in its
regmap config: disable_locking = true
To avoid this issue, use the driver's own lock to do the protect
in system PM.
Fixes: b765743005 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d07a692f9 ]
We should use of_node_get() when a new reference of device_node
is created. It is noted that the old reference stored in
'mm_gc->gc.of_node' should also be decreased.
This patch is based on the fact that there is a call site in function
'qe_add_gpiochips()' of src file 'drivers\soc\fsl\qe\gpio.c'. In this
function, of_mm_gpiochip_add_data() is contained in an iteration of
for_each_compatible_node() which will automatically increase and
decrease the refcount. So we need additional of_node_get() for the
reference escape in of_mm_gpiochip_add_data().
Fixes: a19e3da5bc ("of/gpio: Kill of_gpio_chip and add members directly to gpio_chip")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8c768ccdd ]
For regcache_sync_region, we need to use pca953x_recalc_addr() to get
the real register address.
Fixes: ec82d1eba3 ("gpio: pca953x: Zap ad-hoc reg_output cache")
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2abc17a938 ]
regmap will sync a range of registers, here use the correct range
to make sure the sync do not touch other unexpected registers.
Find on pca9557pw on imx8qxp/dxl evk board, this device support
8 pin, so only need one register(8 bits) to cover all the 8 pins's
property setting. But when sync the output, we find it actually
update two registers, output register and the following register.
Fixes: b765743005 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Fixes: ec82d1eba3 ("gpio: pca953x: Zap ad-hoc reg_output cache")
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db8edaa09d ]
For the device use NO AI mode(not support auto address increment),
only use the single read/write when config the regmap.
We meet issue on PCA9557PW on i.MX8QXP/DXL evk board, this device
do not support AI mode, but when do the regmap sync, regmap will
sync 3 byte data to register 1, logically this means write first
data to register 1, write second data to register 2, write third data
to register 3. But this device do not support AI mode, finally, these
three data write only into register 1 one by one. the reault is the
value of register 1 alway equal to the latest data, here is the third
data, no operation happened on register 2 and register 3. This is
not what we expect.
Fixes: 4942723276 ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81aba8fde ]
commit 979934da9e ("[PATCH] mips: update IRQ handling for vr41xx") added
a function irq_dispatch, and it'll increase irq_err_count when the get_irq
callback returns a negative value, but increase irq_err_count in get_irq
was not removed.
And also, modpost complains once gpio-vr41xx drivers become modules.
ERROR: modpost: "irq_err_count" [drivers/gpio/gpio-vr41xx.ko] undefined!
So it would be a good idea to remove repetitive increase irq_err_count in
get_irq callback.
Fixes: 27fdd325da ("MIPS: Update VR41xx GPIO driver to use gpiolib")
Fixes: 979934da9e ("[PATCH] mips: update IRQ handling for vr41xx")
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: huhai <huhai@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77006f6edc ]
Currently if the APB or Debounce clocks aren't yet ready to be requested
the DW GPIO driver will correctly handle that by deferring the probe
procedure, but the error is still printed to the system log. It needlessly
pollutes the log since there was no real error but a request to postpone
the clock request procedure since the clocks subsystem hasn't been fully
initialized yet. Let's fix that by using the dev_err_probe method to print
the APB/clock request error status. It will correctly handle the deferred
probe situation and print the error if it actually happens.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43624eda86 ]
For regcache_sync_region, need to use pca953x_recalc_addr() to get
the real register address.
Fixes: b765743005 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3550bba25d ]
Since commit 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
the device tree nodes of GPIO controller need the gpio-ranges property to
handle gpio-hogs. Unfortunately it's impossible to guarantee that every new
kernel is shipped with an updated device tree binary.
In order to provide backward compatibility with those older DTB, we need a
callback within of_gpiochip_add_pin_range() so the relevant platform driver
can handle this case.
Fixes: 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220409095129.45786-2-stefan.wahren@i2se.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bf3ac466f ]
For gpio controller contain register PDDR, when set one target bit,
current logic will clear all other bits, this is wrong. Use operator
'|=' to fix it.
Fixes: 659d8a6231 ("gpio: vf610: add imx7ulp support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dba7857985 upstream.
When one port's input state get inverted (eg. from low to hight) after
pca953x_irq_setup but before setting irq_mask (by some other driver such as
"gpio-keys"), the next inversion of this port (eg. from hight to low) will not
be triggered any more (because irq_stat is not updated at the first time). Issue
should be fixed after this commit.
Fixes: 89ea8bbe9c ("gpio: pca953x.c: add interrupt handling capability")
Signed-off-by: Puyou Lu <puyou.lu@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e75f88efac upstream.
Gpiolib interprets the elements of "gpio-reserved-ranges" as "start,size"
because it clears "size" bits starting from the "start" bit in the according
bitmap. So it has to use "greater" instead of "greater or equal" when performs
bounds check to make sure that GPIOs are in the available range.
Previous implementation skipped ranges that include the last GPIO in
the range.
I wrote the mail to the maintainers
(https://lore.kernel.org/linux-gpio/20220412115554.159435-1-andrei.lalaev@emlid.com/T/#u)
of the questioned DTSes (because I couldn't understand how the maintainers
interpreted this property), but I haven't received a response.
Since the questioned DTSes use "gpio-reserved-ranges = <0 4>"
(i.e., the beginning of the range), this patch doesn't affect these DTSes at all.
TBH this patch doesn't break any existing DTSes because none of them
reserve gpios at the end of range.
Fixes: 726cb3ba49 ("gpiolib: Support 'gpio-reserved-ranges' property")
Signed-off-by: Andrei Lalaev <andrei.lalaev@emlid.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06fb4ecfea upstream.
Commit 5467801f1f ("gpio: Restrict usage of GPIO chip irq members
before initialization") attempted to fix a race condition that lead to a
NULL pointer, but in the process caused a regression for _AEI/_EVT
declared GPIOs.
This manifests in messages showing deferred probing while trying to
allocate IRQs like so:
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x002C to IRQ, err -517
amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x003D to IRQ, err -517
[ .. more of the same .. ]
The code for walking _AEI doesn't handle deferred probing and so this
leads to non-functional GPIO interrupts.
Fix this issue by moving the call to `acpi_gpiochip_request_interrupts`
to occur after gc->irc.initialized is set.
Fixes: 5467801f1f ("gpio: Restrict usage of GPIO chip irq members before initialization")
Link: https://lore.kernel.org/linux-gpio/BL1PR12MB51577A77F000A008AA694675E2EF9@BL1PR12MB5157.namprd12.prod.outlook.com/
Link: https://bugzilla.suse.com/show_bug.cgi?id=1198697
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215850
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1979
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1976
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Shreeya Patel <shreeya.patel@collabora.com>
Tested-By: Samuel Čavoj <samuel@cavoj.net>
Tested-By: lukeluk498@gmail.com Link:
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-and-tested-by: Takashi Iwai <tiwai@suse.de>
Cc: Shreeya Patel <shreeya.patel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 213d266ebf ]
When compiling with -Wformat, clang emits the following warning:
gpiolib-acpi.c:393:4: warning: format specifies type 'unsigned char' but the argument has type 'int' [-Wformat]
pin);
^~~
So warning that '%hhX' is paired with an 'int' is all just completely
mindless and wrong. Sadly, I can see a different bogus warning reason
why people would want to use '%02hhX'.
Again, the *sane* thing from a human perspective is to use '%02X. But
if the compiler doesn't do any range analysis at all, it could decide
that "Oh, that print format could need up to 8 bytes of space in the
result". Using '%02hhX' would cut that down to two.
And since we use
char ev_name[5];
and currently use "_%c%02hhX" as the format string, even a compiler
that doesn't notice that "pin <= 255" test that guards this all will
go "OK, that's at most 4 bytes and the final NUL termination, so it's
fine".
While a compiler - like gcc - that only sees that the original source
of the 'pin' value is a 'unsigned short' array, and then doesn't take
the "pin <= 255" into account, will warn like this:
gpiolib-acpi.c: In function 'acpi_gpiochip_request_interrupt':
gpiolib-acpi.c:206:24: warning: '%02X' directive writing between 2 and 4 bytes into a region of size 3 [-Wformat-overflow=]
sprintf(ev_name, "_%c%02X",
^~~~
gpiolib-acpi.c:206:20: note: directive argument in the range [0, 65535]
because gcc isn't being very good at that argument range analysis either.
In other words, the original use of 'hhx' was bogus to begin with, and
due to *another* compiler warning being bad, and we had that bad code
being written back in 2016 to work around _that_ compiler warning
(commit e40a3ae1f7: "gpio: acpi: work around false-positive
-Wstring-overflow warning").
Sadly, two different bad compiler warnings together does not make for
one good one.
It just makes for even more pain.
End result: I think the simplest and cleanest option is simply the
proposed change which undoes that '%hhX' change for gcc, and replaces
it with just using a slightly bigger stack allocation. It's not like
a 5-byte allocation is in any way likely to have saved any actual stack,
since all the other variables in that function are 'int' or bigger.
False-positive compiler warnings really do make people write worse
code, and that's a problem. But on a scale of bad code, I feel that
extending the buffer trivially is better than adding a pointless cast
that literally makes no sense.
At least in this case the end result isn't unreadable or buggy. We've
had several cases of bad compiler warnings that caused changes that
were actually horrendously wrong.
Fixes: e40a3ae1f7 ("gpio: acpi: work around false-positive -Wstring-overflow warning")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5467801f1f upstream.
GPIO chip irq members are exposed before they could be completely
initialized and this leads to race conditions.
One such issue was observed for the gc->irq.domain variable which
was accessed through the I2C interface in gpiochip_to_irq() before
it could be initialized by gpiochip_add_irqchip(). This resulted in
Kernel NULL pointer dereference.
Following are the logs for reference :-
kernel: Call Trace:
kernel: gpiod_to_irq+0x53/0x70
kernel: acpi_dev_gpio_irq_get_by+0x113/0x1f0
kernel: i2c_acpi_get_irq+0xc0/0xd0
kernel: i2c_device_probe+0x28a/0x2a0
kernel: really_probe+0xf2/0x460
kernel: RIP: 0010:gpiochip_to_irq+0x47/0xc0
To avoid such scenarios, restrict usage of GPIO chip irq members before
they are completely initialized.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc328a7d1f ]
Some GPIO lines have stopped working after the patch
commit 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
And this has supposedly been fixed in the following patches
commit 89ad556b7f ("gpio: Avoid using pin ranges with !PINCTRL")
commit 6dbbf84603 ("gpiolib: Don't free if pin ranges are not defined")
But an erratic behavior where some GPIO lines work while others do not work
has been introduced.
This patch reverts those changes so that the sysfs-gpio interface works
properly again.
Signed-off-by: Marcelo Roberto Jimenez <marcelo.jimenez@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae42f92888 ]
We are racing the registering of .to_irq when probing the
i2c driver. This results in random failure of touchscreen
devices.
Following explains the race condition better.
[gpio driver] gpio driver registers gpio chip
[gpio consumer] gpio is acquired
[gpio consumer] gpiod_to_irq() fails with -ENXIO
[gpio driver] gpio driver registers irqchip
gpiod_to_irq works at this point, but -ENXIO is fatal
We could see the following errors in dmesg logs when gc->to_irq is NULL
[2.101857] i2c_hid i2c-FTS3528:00: HID over i2c has not been provided an Int IRQ
[2.101953] i2c_hid: probe of i2c-FTS3528:00 failed with error -22
To avoid this situation, defer probing until to_irq is registered.
Returning -EPROBE_DEFER would be the first step towards avoiding
the failure of devices due to the race in registration of .to_irq.
Final solution to this issue would be to avoid using gc irq members
until they are fully initialized.
This issue has been reported many times in past and people have been
using workarounds like changing the pinctrl_amd to built-in instead
of loading it as a module or by adding a softdep for pinctrl_amd into
the config file.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209413
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fe003547 ]
This works around an issue with the hardware where both OE and
DAT are exposed in the same register. If both are updated
simultaneously, the harware makes no guarantees that OE or DAT
will actually change in any given order and may result in a
glitch of a few ns on a GPIO pin when changing direction and value
in a single write.
Setting direction to input now only affects OE bit. Setting
direction to output updates DAT first, then OE.
Fixes: 9c6686322d ("gpio: add Technologic I2C-FPGA gpio support")
Signed-off-by: Mark Featherston <mark@embeddedTS.com>
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
