Pull networking fixes from David Miller:
1) Handle errors mid-stream of an all dump, from Alexey Kodanev.
2) Fix build of openvswitch with certain combinations of netfilter
options, from Arnd Bergmann.
3) Fix interactions between GSO and BQL, from Eric Dumazet.
4) Don't put a '/' in RTL8201F's sysfs file name, from Holger
Hoffstätte.
5) S390 qeth driver fixes from Julian Wiedmann.
6) Allow ipv6 link local addresses for netconsole when both source and
destination are link local, from Matwey V. Kornilov.
7) Fix the BPF program address seen in /proc/kallsyms, from Song Liu.
8) Initialize mutex before use in dsa microchip driver, from Tristram
Ha.
9) Out-of-bounds access in hns3, from Yunsheng Lin.
10) Various netfilter fixes from Stefano Brivio, Jozsef Kadlecsik, Jiri
Slaby, Florian Westphal, Eric Westbrook, Andrey Ryabinin, and Pablo
Neira Ayuso.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (50 commits)
net: alx: make alx_drv_name static
net: bpfilter: fix iptables failure if bpfilter_umh is disabled
sock_diag: fix autoloading of the raw_diag module
net: core: netpoll: Enable netconsole IPv6 link local address
ipv6: properly check return value in inet6_dump_all()
rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
bonding/802.3ad: fix link_failure_count tracking
net: phy: realtek: fix RTL8201F sysfs name
sctp: define SCTP_SS_DEFAULT for Stream schedulers
sctp: fix strchange_flags name for Stream Change Event
mlxsw: spectrum: Fix IP2ME CPU policer configuration
openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
qed: fix link config error handling
net: hns3: Fix for out-of-bounds access when setting pfc back pressure
net/mlx4_en: use __netdev_tx_sent_queue()
net: do not abort bulk send on BQL status
net: bql: add __netdev_tx_sent_queue()
s390/qeth: report 25Gbit link speed
s390/qeth: sanitize ARP requests
...
alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d2c0cda07 set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.
Fixes: 4d2c0cda07 ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
private struct, and a few bug fixes.
-----BEGIN PGP SIGNATURE-----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=EhpD
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.20' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Fairly minor changes and bug fixes:
NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
private struct, and a few bug fixes"
* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
ntb: idt: Alter the driver info comments
ntb: idt: Discard temperature sensor IRQ handler
ntb: idt: Add basic hwmon sysfs interface
ntb: idt: Alter temperature read method
ntb_netdev: Simplify remove with client device drvdata
NTB: transport: Try harder to alloc an aligned MW buffer
ntb: ntb_transport: Mark expected switch fall-throughs
ntb: idt: Set PCIe bus address to BARLIMITx
NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
ntb: intel: fix return value for ndev_vec_mask()
ntb_netdev: fix sleep time mismatch
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73 ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[ 35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[ 35.254141] Workqueue: events work_for_cpu_fn
[ 35.254144] Call trace:
[ 35.254147] dump_backtrace+0x0/0x2f0
[ 35.254149] show_stack+0x24/0x30
[ 35.254154] dump_stack+0x110/0x184
[ 35.254157] print_address_description+0x168/0x2b0
[ 35.254160] kasan_report+0x184/0x310
[ 35.254162] __asan_load2+0x7c/0xa0
[ 35.254170] hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254177] hclge_tm_init_hw+0x794/0x9f0 [hclge]
[ 35.254184] hclge_tm_schd_init+0x48/0x58 [hclge]
[ 35.254191] hclge_init_ae_dev+0x778/0x1168 [hclge]
[ 35.254196] hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[ 35.254206] hns3_probe+0x88/0xa8 [hns3]
[ 35.254210] local_pci_probe+0x7c/0xf0
[ 35.254212] work_for_cpu_fn+0x34/0x50
[ 35.254214] process_one_work+0x4d4/0xa38
[ 35.254216] worker_thread+0x55c/0x8d8
[ 35.254219] kthread+0x1b0/0x1b8
[ 35.254222] ret_from_fork+0x10/0x1c
[ 35.254224] The buggy address belongs to the page:
[ 35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 35.273835] flags: 0xfffff8000008000(head)
[ 35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[ 35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 35.282012] page dumped because: kasan: bad access detected
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
doorbell only depends on xmit_more and netif_tx_queue_stopped()
Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.
This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize mutex before use. Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) BPF verifier fixes from Daniel Borkmann.
2) HNS driver fixes from Huazhong Tan.
3) FDB only works for ethernet devices, reject attempts to install FDB
rules for others. From Ido Schimmel.
4) Fix spectre V1 in vhost, from Jason Wang.
5) Don't pass on-stack object to irq_set_affinity_hint() in mvpp2
driver, from Marc Zyngier.
6) Fix mlx5e checksum handling when RXFCS is enabled, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (49 commits)
openvswitch: Fix push/pop ethernet validation
net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
bpf: test make sure to run unpriv test cases in test_verifier
bpf: add various test cases to test_verifier
bpf: don't set id on after map lookup with ptr_to_map_val return
bpf: fix partial copy of map_ptr when dst is scalar
libbpf: Fix compile error in libbpf_attach_type_by_name
kselftests/bpf: use ping6 as the default ipv6 ping binary if it exists
selftests: mlxsw: qos_mc_aware: Add a test for UC awareness
selftests: mlxsw: qos_mc_aware: Tweak for min shaper
mlxsw: spectrum: Set minimum shaper on MC TCs
mlxsw: reg: QEEC: Add minimum shaper fields
net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()
net: hns3: bugfix for rtnl_lock's range in the hclge_reset()
net: hns3: bugfix for handling mailbox while the command queue reinitialized
net: hns3: fix incorrect return value/type of some functions
net: hns3: bugfix for hclge_mdio_write and hclge_mdio_read
net: hns3: bugfix for is_valid_csq_clean_head()
net: hns3: remove unnecessary queue reset in the hns3_uninit_all_ring()
net: hns3: bugfix for the initialization of command queue's spin lock
...
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.
When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().
Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.
Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.
Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-10-31
This series contains a various collection of fixes.
Miroslav Lichvar from Red Hat or should I say IBM now? Updates the PHC
timecounter interval for igb so that it gets updated at least once
every 550 seconds.
Ngai-Mint provides a fix for fm10k to prevent a soft lockup or system
crash by adding a new condition to determine if the SM mailbox is in the
correct state before proceeding.
Jake provides several fm10k fixes, first one marks complier aborts as
non-fatal since on some platforms trigger machine check errors when the
compile aborts. Added missing device ids to the in-kernel driver. Due
to the recent fixes, bumped the driver version.
I (Jeff Kirsher) fixed a XFRM_ALGO dependency for both ixgbe and
ixgbevf. This fix was based on the original work from Arnd Bergmann,
which only fixed ixgbe.
Mitch provides a fix for i40e/avf to update the status codes, which
resolves an issue between a mis-match between i40e and the iavf driver,
which also supports the ice LAN driver.
Radoslaw fixes the ixgbe where the driver is logging a message about
spoofed packets detected when the VF is re-started with a different MAC
address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the elaborate private structure global linked-list used in
ntb_netdev_probe() and ntb_netdev_remove() by stashing our private
data in the NTB transport client device.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The tx_time should be in usecs (according to the comment above the
variable), but the setting of the timer during the rearming is done in
msecs. Change it to match the expected units.
Fixes: e74bfeedad ("NTB: Add flow control to the ntb_netdev")
Suggested-by: Gerd W. Haeussler <gerd.haeussler@cesys-it.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Dave Jiang <dave.jiang@intel.com>
An MC-aware mode was introduced in commit 7b81953066 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"). In MC-aware mode,
BUM traffic gets a special treatment by being assigned to a separate set
of traffic classes 8..15. Pairs of TCs 0 and 8, 1 and 9, etc., are then
configured to strictly prioritize the lower-numbered ones. The intention
is to prevent BUM traffic from flooding the switch and push out all UC
traffic, which would otherwise happen, and instead give UC traffic
precedence.
However strictly prioritizing UC traffic has the effect that UC overload
pushes out all BUM traffic, such as legitimate ARP queries. These
packets are kept in queues for a while, but under sustained UC overload,
their lifetime eventually expires and these packets are dropped. That is
detrimental to network performance as well.
Therefore configure the MC TCs (8..15) with minimum shaper of 200Mbps (a
minimum permitted value) to allow a trickle of necessary control traffic
to get through.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add QEEC.mise (minimum shaper enable) and QEEC.min_shaper_rate to enable
configuration of minimum shaper.
Increase the QEEC length to 0x20 as well: that's the length that the
register has had for a long time now, but with the configurations that
mlxsw typically exercises, the firmware tolerated 0x1C-sized packets.
With mise=true however, FW rejects packets unless they have the full
required length.
Fixes: b9b7cee405 ("mlxsw: reg: Add QoS ETS Element Configuration register")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().
Fixes: 6d4fab3953 ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.
The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 681ec3999b ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is a PHY, the driver needs to complete some operations through
MDIO during reset reinitialization, so HCLGE_STATE_CMD_DISABLE is more
suitable than HCLGE_STATE_RST_HANDLING to prevent the MDIO operation from
being sent during the hardware reset.
Fixes: b50ae26c57 ("net: hns3: never send command queue message to IMP when reset)
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HEAD pointer of the hardware command queue maybe equal to the command
queue's next_to_use in the driver, so that does not belong to the invalid
HEAD pointer, since the hardware may not process the command in time,
causing the HEAD pointer to be too late to update. The variables' name
in this function is unreadable, so give them a more readable one.
Fixes: 3ff504908f ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not necessary to reset the queue in the hns3_uninit_all_ring(),
since the queue is stopped in the down operation, and will be reset
in the up operation. And the judgment of the HCLGE_STATE_RST_HANDLING
flag in the hclge_reset_tqp() is not correct, because we need to reset
tqp during pf reset, otherwise it may cause queue not being reset to
working state problem.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.
Fixes: 3efb960f05 ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver supports handling two vector0 interrupts, reset and
mailbox. When the hardware reports an interrupt of another type of
interrupt source, if the driver does not process the interrupt, but
enables the interrupt, the hardware will repeatedly report the unknown
interrupt.
Therefore, the driver enables the vector0 interrupt after clearing the
known type of interrupt source. Other conditions are not enabled.
Fixes: cd8c5c269b ("net: hns3: Fix for hclge_reset running repeatly problem")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_nic_init_vector_data() fails to map ring to vector,
it should cancel the netif_napi_add() that has been successfully
done and then exits.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As shown by Dmitris, we need to use csum_block_add() instead of csum_add()
when adding the FCS contribution to skb csum.
Before 4.18 (more exactly commit 88078d98d1 "net: pskb_trim_rcsum()
and CHECKSUM_COMPLETE are friends"), the whole skb csum was thrown away,
so RXFCS changes were ignored.
Then before commit d55bef5059 ("net: fix pskb_trim_rcsum_slow() with
odd trim offset") both mlx5 and pskb_trim_rcsum_slow() bugs were canceling
each other.
Now we fixed pskb_trim_rcsum_slow() we need to fix mlx5.
Note that this patch also rewrites mlx5e_get_fcs() to :
- Use skb_header_pointer() instead of reinventing it.
- Use __get_unaligned_cpu32() to avoid possible non aligned accesses
as Dmitris pointed out.
Fixes: 902a545904 ("net/mlx5e: When RXFCS is set, add FCS data into checksum calculation")
Reported-by: Paweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Dimitris Michailidis <dmichail@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Paweł Staszewski <pstaszewski@itcare.pl>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Tested-By: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.
MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a few new status code which will be used by the ice driver, and
rename a few to make them more consistent. Error code are mapped to
similar values as in i40e_status.h, so as to be compatible with older
VF drivers not using this status enum.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original work from Arnd Bergmann.
When XFRM_ALGO is not enabled, the new ixgbe IPsec code produces a
link error:
drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.o: In function `ixgbe_ipsec_vf_add_sa':
ixgbe_ipsec.c:(.text+0x1266): undefined reference to `xfrm_aead_get_byname'
Simply selecting XFRM_ALGO from here causes circular dependencies, so
to fix it, we probably want this slightly more complex solution that is
similar to what other drivers with XFRM offload do:
A separate Kconfig symbol now controls whether we include the IPsec
offload code. To keep the old behavior, this is left as 'default y'. The
dependency in XFRM_OFFLOAD still causes a circular dependency but is
not actually needed because this symbol is not user visible, so removing
that dependency on top makes it all work.
CC: Arnd Bergmann <arnd@arndb.de>
CC: Shannon Nelson <shannon.nelson@oracle.com>
Fixes: eda0333ac2 ("ixgbe: add VF IPsec management")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The upstream and out-of-tree drivers are once again at comparable
functionality. It's been a while since we updated the upstream driver
version, so bump it now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device IDs for the Ethernet SDI Adapter devices were never added to
the upstream driver. The IDs are already in the pci.ids database, and
are supported by the out-of-tree driver.
Add the device IDs now, so that the upstream driver can recognize and
load these devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers can trigger PCIe completer aborts any time they read a queue
that they don't own. Even in nominal circumstances, it is not possible
to prevent the VF driver from reading queues it doesn't own. VF drivers
may attempt to read queues it previously owned, but which it no longer
does due to a PF reset.
Normally these completer aborts aren't an issue. However, on some
platforms these trigger machine check errors. This is true even if we
lower their severity from fatal to non-fatal. Indeed, we already have
code for lowering the severity.
We could attempt to mask these errors conditionally around resets, which
is the most common time they would occur. However this would essentially
be a race between the PF and VF drivers, and we may still occasionally
see machine check exceptions on these strictly configured platforms.
Instead, mask the errors entirely any time we resume VFs. By doing so,
we prevent the completer aborts from being sent to the parent PCIe
device, and thus these strict platforms will not upgrade them into
machine check errors.
Additionally, we don't lose any information by masking these errors,
because we'll still report VFs which attempt to access queues via the
FUM_BAD_VF_QACCESS errors.
Without this change, on platforms where completer aborts cause machine
check exceptions, the VF reading queues it doesn't own could crash the
host system. Masking the completer abort prevents this, so we should
mask it for good, and not just around a PCIe reset. Otherwise malicious
or misconfigured VFs could cause the host system to crash.
Because we are masking the error entirely, there is little reason to
also keep setting the severity bit, so that code is also removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current condition will always incorrectly report a full SM mailbox if an
IES API application is not running. Due to this, the
"fm10k_service_task" will be infinitely queued into the driver's
workqueue. This, in turn, will cause a "kworker" thread to report 100%
CPU utilization and might cause "soft lockup" events or system crashes.
To fix this issue, a new condition is added to determine if the SM
mailbox is in the correct state of FM10K_STATE_OPEN before proceeding.
In other words, an instance of the IES API must be running. If there is,
the remainder of the flow stays the same which is to determine if the SM
mailbox capacity has been exceeded or not and take appropriate action.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9d ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Shorten
the delay to 480 seconds to be sure the timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mvpp2 driver has the curious behaviour of passing a stack variable
to irq_set_affinity_hint(), which results in the kernel exploding
the first time anyone accesses this information. News flash: userspace
does, and irqbalance will happily take the machine down. Great stuff.
An easy fix is to track the mask within the queue_vector structure,
and to make sure it has the same lifetime as the interrupt itself.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abdul Haleem reported a build error on ppc :
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: `struct
iphdr` declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is
only this definition or declaration, which is probably not what you want
[enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function
get_fixed_ipv4_csum:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing
pointer to incomplete type
__u8 ipproto = iph->protocol;
^
Fixes: 55469bc6b5 ("drivers: net: remove <net/busy_poll.h> inclusion when not needed")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a failed reload, the driver is still registered to devlink, its
devlink instance is still allocated and the 'reload_fail' flag is set.
Then, in the next reload try, the driver's allocated devlink instance will
be freed without unregistering from devlink and its components (e.g,
resources). This scenario can cause a use-after-free if the user tries to
execute command via devlink user-space tool.
Fix by not freeing the devlink instance during reload (failed or not).
Fixes: 24cc68ad6c ("mlxsw: core: Add support for reload")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Demands to remove FDB entries should be honored even if the FDB entry in
question was originally learned, and not added by the user. Therefore
ignore the added_by_user datum for SWITCHDEV_FDB_DEL_TO_DEVICE.
Fixes: 816a3bed95 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/huawei/hinic/hinic_tx.c:392:34: error: implicit
conversion from enumeration type 'enum hinic_l4_tunnel_type' to
different enumeration type 'enum hinic_l4_offload_type'
[-Werror,-Wenum-conversion]
hinic_task_set_tunnel_l4(task, TUNNEL_UDP_NO_CSUM,
~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~
1 error generated.
It seems that hinic_task_set_tunnel_l4 was meant to take an enum of type
hinic_l4_tunnel_type, not hinic_l4_offload_type, given both the name of
the functions and the values used.
Fixes: cc18a7543d ("net-next/hinic: add checksum offload and TSO support")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attribute IFLA_BOND_AD_ACTOR_SYSTEM is sent to user space having the
length of sizeof(bond->params.ad_actor_system) which is 8 byte. This
patch aligns the length to ETH_ALEN to have the same MAC address exposed
as using sysfs.
Fixes: f87fda00b6 ("bonding: prevent out of bound accesses")
Signed-off-by: Tobias Jungel <tobias.jungel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the kernel doesn't let the administrator set a macsec device
up unless its lower device is currently up. This is inconsistent, as a
macsec device that is up won't automatically go down when its lower
device goes down.
Now that linkstate propagation works, there's really no reason for this
limitation, so let's remove it.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like all other virtual devices (macvlan, vlan), the operstate of a
macsec device should match the state of its lower device. This is done
by calling netif_stacked_transfer_operstate from its netdevice notifier.
We also need to call netif_stacked_transfer_operstate when a new macsec
device is created, so that its operstate is set properly. This is only
relevant when we try to bring the device up directly when we create it.
Radu Rendec proposed a similar patch, inspired from the 802.1q driver,
that included changing the administrative state of the macsec device,
instead of just the operstate. This version is similar to what the
macvlan driver does, and updates only the operstate.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Radu Rendec <radu.rendec@gmail.com>
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
