Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different
from the tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit operations
to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries
to access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ttgq
-----END PGP SIGNATURE-----
Merge tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different from the
tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the
workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit
operations to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries to
access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs"
* tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (123 commits)
selftests/net: udpgso_bench_rx: fix port argument
net: wwan: iosm: fix compilation warning
cxgb4: fix eeprom len when diagnostics not implemented
net: fix premature exit from NAPI state polling in napi_disable()
net/smc: fix sk_refcnt underflow on linkdown and fallback
net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
gve: fix unmatched u64_stats_update_end()
net: ethernet: lantiq_etop: Fix compilation error
selftests: forwarding: Fix packet matching in mirroring selftests
vsock: prevent unnecessary refcnt inc for nonblocking connect
net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
net: stmmac: allow a tc-taprio base-time of zero
selftests: net: test_vxlan_under_vrf: fix HV connectivity test
net: hns3: allow configure ETS bandwidth of all TCs
net: hns3: remove check VF uc mac exist when set by PF
net: hns3: fix some mac statistics is always 0 in device version V2
net: hns3: fix kernel crash when unload VF while it is being reset
net: hns3: sync rx ring head in echo common pull
net: hns3: fix pfc packet number incorrect after querying pfc parameters
...
Currently, driver only allow configuring ETS bandwidth of TCs according
to the max TC number queried from firmware. However, the hardware actually
supports 8 TCs and users may need to configure ETS bandwidth of all TCs,
so remove the restriction.
Fixes: 330baff542 ("net: hns3: add ETS TC weight setting in SSU module")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If users set unicast mac address for VFs by PF, they need to guarantee all
VFs' address is different. This patch removes the check mac address exist
of VFs, for usrs can refresh mac addresses of all VFs directly without
need to modify the exist mac address to other value firstly.
Fixes: 8e6de441b8 ("net: hns3: add support for configuring VF MAC from the host")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver queries the register number of mac statistics from firmware,
the old firmware runs in device version V2 only returns number of valid
registers, not include number of three reserved registers among of them.
It cause driver doesn't record the last three data when query mac
statistics.
To fix this problem, driver never query register number in device version
V2 and set it to a fixed value which include three reserved registers.
Fixes: c8af2887c9 ("net: hns3: add support pause/pfc durations for mac statistics")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver processes rx packets, the head pointer is updated only
after the number of received packets reaches 16. However, hardware
relies on the head pointer to calculate the number of FBDs. As a result,
the hardware calculates the FBD incorrectly. Therefore, the driver
proactively updates the head pointer in each common poll to ensure that
the number of FBDs calculated by the hardware is correct.
Fixes: 68752b24f5 ("net: hns3: schedule the polling again when allocation fails")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver will send command to firmware to query pfc packet number
when user uses dcb tool to get pfc parameters. However, the periodic
service task will also periodically query and record MAC statistics,
including pfc packet number.
As the hardware registers of statistics is cleared after reading, it will
cause pfc packet number of MAC statistics are not correct after using dcb
tool to get pfc parameters.
To fix this problem, when user uses dcb tool to get pfc parameters, driver
updates MAC statistics firstly and then get pfc packet number from MAC
statistics.
Fixes: 64fd2300fc ("net: hns3: add support for querying pfc puase packets statistic")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, NIC init ROCE interrupt vector with MSIX interrupt. But ROCE use
pci_irq_vector() to get interrupt vector, which adds the relative interrupt
vector again and gets wrong interrupt vector.
So fixes it by assign relative interrupt vector to ROCE instead of MSIX
interrupt vector and delete the unused struct member base_msi_vector
declaration of hclgevf_dev.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when driver is failed to add a new multicast mac address to
hardware due to the multicast mac table is full, it will directly return.
In this case, if the multicast mac list has some reuse addresses after the
new address, those reuse addresses will never be added to hardware.
To fix this problem, if function hclge_add_mc_addr_common() returns
-ENOSPC, hclge_sync_vport_mac_list() should judge whether continue or
stop to add next address.
As function hclge_sync_vport_mac_list() needs parameter mac_type to know
whether is uc or mc, refine this function to add parameter mac_type and
remove parameter sync. So does function hclge_unsync_vport_mac_list().
Fixes: ee4bcd3b7a ("net: hns3: refactor the MAC address configure")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings and spacing in hns3_ethtool.c:
hns3_ethtool.c:246: warning: No description found for return value of 'hns3_lp_run_test'
hns3_ethtool.c:408: warning: expecting prototype for hns3_nic_self_test(). Prototype was for hns3_self_test() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Peng Li <lipeng321@huawei.com>
Cc: Guangbin Huang <huangguangbin2@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
This patch adjusts the string spaces of some parameters of tx bd info in
debugfs according to their maximum needs.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The specified buffer length for three debugfs files fd_tcam, uc and tqp
is not enough for their maximum needs, so this patch fixes them.
Fixes: b5a0b70d77 ("net: hns3: refactor dump fd tcam of debugfs")
Fixes: 1556ea9120 ("net: hns3: refactor dump mac list of debugfs")
Fixes: d96b0e5946 ("net: hns3: refactor dump reg of debugfs")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the width of packets number registers is 32 bits, they needs at most
10 characters for decimal data printing, but now the string spaces is not
enough, so this patch fixes it.
Fixes: e44c495d95 ("net: hns3: refactor queue info of debugfs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member data in struct hclge_desc is type of __le32, it needs endian
conversion before using it, and some functions of debugfs didn't do that,
so this patch fixes it.
Fixes: c0ebebb9cc ("net: hns3: Add "dcb register" status information query function")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the workqueue of hclge/hclgevf is executed on
the CPU that initiates scheduling requests by default. In
stress scenarios, the CPU may be busy and workqueue scheduling
is completed after a long period of time. To avoid this
situation and implement proper scheduling, use the WQ_UNBOUND
mode instead. In this way, the workqueue can be performed on
a relatively idle CPU.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a TP port is configured by follow steps:
1.ethtool -s ethx autoneg off speed 100 duplex full
2.ethtool -A ethx rx on tx on
3.ethtool -s ethx autoneg on(rx&tx negotiated pause results are off)
4.ethtool -s ethx autoneg off speed 100 duplex full
In step 3, driver will set rx&tx pause parameters of hardware to off as
pause parameters negotiated with link partner are off.
After step 4, the "ethtool -a ethx" command shows both rx and tx pause
parameters are on. However, pause parameters of hardware are still off
and port has no flow control function actually.
To fix this problem, if autoneg is disabled, driver uses its saved
parameters to restore pause of hardware. If the speed is not changed in
this case, there is no link state changed for phy, it will cause the pause
parameter is not taken effect, so we need to force phy to go down and up.
Fixes: aacbe27e82 ("net: hns3: modify how pause options is displayed")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds himac error recovery module, link_error type and
ptp_error type for himac.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds one ras error of bus related for roce, this error
including RRESP/BRESP and read poison error.
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the ethtool advertised link modes of FIBRE port is cleared to
zero when autoneg is off, so user can not get the advertised link modes
info directly from "ethtool <dev>" command.
In order to ameliorate this situation, update data of speeds, fec and pause
of advertised link modes when autoneg is off.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions of converting speed ability to ethtool link mode just
support setting mac->supported currently, to reuse these functions to
set ethtool link mode for others(i.e. advertising), delete the argument
mac and add argument link_mode.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac statistics add pause/pfc durations in device version V3, we can
get total active cycle of pause/pfc from these durations.
As driver gets register number from firmware to calculate desc number to
query mac statistics, it needs to set mac statistics extended enable bit
in firmware command 0x701A to tell firmware that driver supports extended
mac statistics, otherwise firmware only returns register number of
version V1.
As pause/pfc durations are not supported by hardware of old version, they
should not been shown in command "ethtool -S ethX" in this case, so add
checking max register number of each mac statistic in their version.
If the max register number of one mac statistic is greater than register
number got from firmware, it means hardware does not support this mac
statistic, so ignore this statistic when get string and data of mac
statistic.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver queries number of mac statistics before querying mac
statistics. As the number of mac statistics is a fixed value in firmware,
it is redundant to query this number everytime before querying mac
statistics, it can just be queried once in initialization process and
saved in device specifications.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After querying mac statistics from firmware, driver copies data from
descriptors to struct mac_stats of hdev, and the number of copied data
is just according to the register number queried from firmware. There is
a problem that if the register number queried from firmware is larger
than data number of struct mac_stats, it will cause a copy overflow.
So if the firmware adds more mac statistics in later version, it is not
compatible with driver of old version.
To fix this problem, the number of copied data needs to be used the
minimum value between the register number queried from firmware and
data number of struct mac_stats.
The first descriptor has three data and there is one reserved, to
optimize the copy process, add this reserverd data to struct mac_stats.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since user may need to check the current configuration of the
interrupt coalesce, so add debugfs support for query this info.
Create a single file "coalesce_info" for it, and query it by
"cat coalesce_info", return the result to userspace.
For device whose version is above V3(include V3), the GL's register
contains usecs and 1us unit configuration. When get the usecs
configuration from this register, it will include the confusing unit
configuration, so add a GL mask to get the correct value, and add
a QL mask for the frames configuration as well.
The display style is below:
$ cat coalesce_info
tx interrupt coalesce info:
VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT...
0 IN_PROG 4 EQE ON_TOP 0...
1 START 3 EQE LEFT 1...
rx interrupt coalesce info:
VEC_ID ALGO_STATE PROFILE_ID CQE_MODE TUNE_STATE STEPS_LEFT...
0 IN_PROG 3 EQE LEFT 1...
1 IN_PROG 0 EQE ON_TOP 0...
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e58 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add configuration of interrupt type and fifo interrupt enable of TM QCN
error event if enabled, otherwise this event will not be reported when
there is error.
Fixes: d914971df0 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of drivers use eth_random_addr(netdev->dev_addr)
thus writing to netdev->dev_addr directly, and not setting
the address type. Switch them to eth_hw_addr_random().
@@
expression netdev;
@@
- eth_random_addr(netdev->dev_addr);
+ eth_hw_addr_random(netdev);
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a0c76345e3 ("devlink: disallow reload operation during device
cleanup") added devlink_reload_{enable,disable}() APIs to prevent reload
operation from racing with device probe/dismantle.
After recent changes to move devlink_register() to the end of device
probe and devlink_unregister() to the beginning of device dismantle,
these races can no longer happen. Reload operations will be denied if
the devlink instance is unregistered and devlink_unregister() will block
until all in-flight operations are done.
Therefore, remove these devlink_reload_{enable,disable}() APIs.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce new devlink call to set feature mask to control devlink
behavior during device initialization phase after devlink_alloc()
is already called.
This allows us to set reload ops based on device property which
is not known at the beginning of driver initialization.
For the sake of simplicity, this API lacks any type of locking and
needs to be called before devlink_register() to make sure that no
parallel access to the ops is possible at this stage.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace dev->driver_name() by dev_driver_string() for the corresponding
struct device. This is a step toward removing pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, take the opportunity to refactor the hnae_handle structure to switch
the last member to flexible array, changing the code accordingly. Also,
fix the comment in the hnae_vf_cb structure to inform that the ae_handle
member must be the last member.
Then, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
This code was detected with the help of Coccinelle and audited and fixed
manually.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new device_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- device_get_mac_address(np, dev->dev_addr, ETH_ALEN)
+ device_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
