Fix a bug in which the receiving of packets can stop in the zero-copy
driver. Ice HW ignores 3 lower bits from QRX_TAIL register, which means
that tail is bumped only on intervals of 8. Currently with XSK RX
batching in place, ice_alloc_rx_bufs_zc() clears the status_error0 only
of the last descriptor that has been allocated/taken from the XSK buffer
pool. status_error0 includes DD bit that is looked upon by the
ice_clean_rx_irq_zc() to tell if a descriptor can be processed.
The bug can be triggered when driver updates the ntu but not the
QRX_TAIL, so HW wouldn't have a chance to write to the ready
descriptors. Later on driver moves the ntc to the mentioned set of
descriptors and interprets them as a ready to be processed, since
corresponding DD bits were not cleared nor any writeback has happened
that would clear it. This can then lead to ntc == ntu case which means
that ring is empty and no further packet processing.
Fix the XSK traffic hang that can be observed when l2fwd scenario from
xdpsock is used by making sure that status_error0 is cleared for each
descriptor that is fed to HW and therefore we are sure that driver will
not processed non-valid DD bits. This will also prevent the driver from
processing the descriptors that were allocated in favor of the
previously processed ones, but writeback didn't happen yet.
Fixes: db804cfc21 ("ice: Use the xsk batched rx allocation interface")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a VF goes through a reset, it's possible for the VF's feature set
to change. For example it may lose the VIRTCHNL_VF_OFFLOAD_VLAN
capability after VF reset. Unfortunately, the driver doesn't correctly
deal with this situation and errors are seen from downing/upping the
interface and/or moving the interface in/out of a network namespace.
When setting the interface down/up we see the following errors after the
VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from the VF:
ice 0000:51:00.1: VF 1 failed opcode 12, retval: -64 iavf 0000:51:09.1:
Failed to add VLAN filter, error IAVF_NOT_SUPPORTED ice 0000:51:00.1: VF
1 failed opcode 13, retval: -64 iavf 0000:51:09.1: Failed to delete VLAN
filter, error IAVF_NOT_SUPPORTED
These add/delete errors are happening because the VLAN filters are
tracked internally to the driver and regardless of the VLAN_ALLOWED()
setting the driver tries to delete/re-add them over virtchnl.
Fix the delete failure by making sure to delete any VLAN filter tracking
in the driver when a removal request is made, while preventing the
virtchnl request. This makes it so the driver's VLAN list is up to date
and the errors are
Fix the add failure by making sure the check for VLAN_ALLOWED() during
reset is done after the VF receives its capability list from the PF via
VIRTCHNL_OP_GET_VF_RESOURCES. If VLAN functionality is not allowed, then
prevent requesting re-adding the filters over virtchnl.
When moving the interface into a network namespace we see the following
errors after the VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from
the VF:
iavf 0000:51:09.1 enp81s0f1v1: NIC Link is Up Speed is 25 Gbps Full Duplex
iavf 0000:51:09.1 temp_27: renamed from enp81s0f1v1
iavf 0000:51:09.1 mgmt: renamed from temp_27
iavf 0000:51:09.1 dev27: set_features() failed (-22); wanted 0x020190001fd54833, left 0x020190001fd54bb3
These errors are happening because we aren't correctly updating the
netdev capabilities and dealing with ndo_fix_features() and
ndo_set_features() correctly.
Fix this by only reporting errors in the driver's ndo_set_features()
callback when VIRTCHNL_VF_OFFLOAD_VLAN is not allowed and any attempt to
enable the VLAN features is made. Also, make sure to disable VLAN
insertion, filtering, and stripping since the VIRTCHNL_VF_OFFLOAD_VLAN
flag applies to all of them and not just VLAN stripping.
Also, after we process the capabilities in the VF reset path, make sure
to call netdev_update_features() in case the capabilities have changed
in order to update the netdev's feature set to match the VF's actual
capabilities.
Lastly, make sure to always report success on VLAN filter delete when
VIRTCHNL_VF_OFFLOAD_VLAN is not supported. The changed flow in
iavf_del_vlans() allows the stack to delete previosly existing VLAN
filters even if VLAN filtering is not allowed. This makes it so the VLAN
filter list is up to date.
Fixes: 8774370d26 ("i40e/i40evf: support for VF VLAN tag stripping control")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently iavf adapter statistics are refreshed only in a
watchdog task, triggered approximately every two seconds,
which causes some ethtool requests to return outdated values.
Add explicit statistics refresh when requested by ethtool -S.
Fixes: b476b0030e ("iavf: Move commands processing to the separate function")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
System hangs if close the interface is called from the kernel during
the interface is in resetting state.
During resetting operation the link is closing but kernel didn't
know it and it tried to close this interface again what sometimes
led to deadlock.
Inform kernel about current state of interface
and turn off the flag IFF_UP when interface is closing until reset
is finished.
Previously it was most likely to hang the system when kernel
(network manager) tried to close the interface in the same time
when interface was in resetting state because of deadlock.
Fixes: 3c8e0b989a ("i40vf: don't stop me now")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Resolve being able to change static values on VF when adaptive interrupt
moderation is enabled.
This problem is fixed by checking the interrupt settings is not
a combination of change of static value while adaptive interrupt
moderation is turned on.
Without this fix, the user would be able to change static values
on VF with adaptive moderation enabled.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Nitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-11-17
This series contains updates to i40e driver only.
Eryk adds accounting for VLAN header in packet size when VF port VLAN is
configured. He also fixes TC queue distribution when the user has changed
queue counts as well as for configuration of VF ADQ which caused dropped
packets.
Michal adds tracking for when a VSI is being released to prevent null
pointer dereference when managing filters.
Karen ensures PF successfully initiates VF requested reset which could
cause a call trace otherwise.
Jedrzej moves validation of channel queue value earlier to prevent
partial configuration when the value is invalid.
Grzegorz corrects the reported error when adding filter fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in [1], e100 was no longer working for suspend/resume
cycles. The previous commit mentioned in the fixes appears to have
broken things and this attempts to practice best known methods for
device power management and keep wake-up working while allowing
suspend/resume to work. To do this, I reorder a little bit of code
and fix the resume path to make sure the device is enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=214933
Fixes: 69a74aef8a ("e100: use generic power management")
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reported-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Alexey Kuznetsov <axet@me.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misleading display error in dmesg if tc filter return fail.
Only i40e status error code should be converted to string, not linux
error code. Otherwise, we return false information about the error.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reject TCs creation with proper message if the first queue
assignment is not equal to the power of two.
The first queue number was checked too late in the second queue
iteration, if second queue was configured at all. Now if first queue value
is not a power of two, then trying to create qdisc will be rejected.
Fixes: 8f88b3034d ("i40e: Add infrastructure for queue channel support")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Restore part of reset functionality used when reset is called
from the VF to reset itself. Without this fix warning message
is displayed when VF is being removed via sysfs.
Fix the crash of the VF during reset by ensuring
that the PF receives the reset message successfully.
Refactor code to use one function instead of two.
Fixes: 5c3c48ac6b ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Properly reconfigure VF VSIs after VF request ADQ.
Created new function to update queue mapping and queue pairs per TC
with AQ update VSI. This sets proper RSS size on NIC.
VFs num_queue_pairs should not be changed during setup of queue maps.
Previously, VF main VSI in ADQ had configured too many queues and had
wrong RSS size, which lead to packets not being consumed and drops in
connectivity.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the i40e_vsi_setup_queue_map is basing the count of queues in
TCs on a VSI's alloc_queue_pairs member which is not changed throughout
any user's action (for example via ethtool's set_channels callback).
This implies that vsi->tc_config.tc_info[n].qcount value that is given
to the kernel via netdev_set_tc_queue() that notifies about the count of
queues per particular traffic class is constant even if user has changed
the total count of queues.
This in turn caused the kernel warning after setting the queue count to
the lower value than the initial one:
$ ethtool -l ens801f0
Channel parameters for ens801f0:
Pre-set maximums:
RX: 0
TX: 0
Other: 1
Combined: 64
Current hardware settings:
RX: 0
TX: 0
Other: 1
Combined: 64
$ ethtool -L ens801f0 combined 40
[dmesg]
Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!
Reason was that vsi->alloc_queue_pairs stayed at 64 value which was used
to set the qcount on TC0 (by default only TC0 exists so all of the
existing queues are assigned to TC0). we update the offset/qcount via
netdev_set_tc_queue() back to the old value but then the
netif_set_real_num_tx_queues() is using the vsi->num_queue_pairs as a
value which got set to 40.
Fix it by using vsi->req_queue_pairs as a queue count that will be
distributed across TCs. Do it only for non-zero values, which implies
that user actually requested the new count of queues.
For VSIs other than main, stay with the vsi->alloc_queue_pairs as we
only allow manipulating the queue count on main VSI.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the reason of null pointer dereference in sync VSI filters.
Added new I40E_VSI_RELEASING flag to signalize deleting and releasing
of VSI resources to sync this thread with sync filters subtask.
Without this patch it is possible to start update the VSI filter list
after VSI is removed, that's causing a kernel oops.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Setting VLAN port increasing RX queue max_pkt_size
by 4 bytes to take VLAN tag into account.
Trigger the VF reset when setting port VLAN for
VF to renegotiate its capabilities and reinitialize.
Fixes: ba4e003d29 ("i40e: don't hold spinlock while resetting VF")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Restore VLAN filters after the link is brought down, and up - since all
filters are deleted from HW during the netdev link down routine.
Fixes: ed1f5b58ea ("i40evf: remove VLAN filters on close")
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now setting combine to 0 will be rejected with the
appropriate error code.
This has been implemented by adding a condition that checks
the value of combine equal to zero.
Without this patch, when the user requested it, no error was
returned and combine was set to the default value for VF.
Fixes: 5520deb153 ("iavf: Enable support for up to 16 queues")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While issuing VF Reset from the guest OS, the VF driver prints
logs about critical / Overflow error detection. This is not an
actual error since the VF_MBX_ARQLEN register is set to all FF's
for a short period of time and the VF would catch the bits set if
it was reading the register during that spike of time.
This patch introduces an additional check to ignore this condition
since the VF is in reset.
Fixes: 19b73d8efa ("i40evf: Add additional check for reset")
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In some cases, the ethtool get_rxfh handler may be called with a null
key or indir parameter. So check these pointers, or you will have a very
bad day.
Fixes: 43a3d9ba34 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In iavf_config_clsflower, the filter structure could be accidentally
released at the end, if iavf_parse_cls_flower or iavf_handle_tclass ever
return a non-zero but positive value.
In this case, the function continues through to the end, and will call
kfree() on the filter structure even though it has been added to the
linked list.
This can actually happen because iavf_parse_cls_flower will return
a positive IAVF_ERR_CONFIG value instead of the traditional negative
error codes.
Fix this by ensuring that the kfree() check and error checks are
similar. Use the more idiomatic "if (err)" to catch all non-zero error
codes.
Fixes: 0075fa0fad ("i40evf: Add support to apply cloud filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver could only quit allmulti when allmulti and promisc modes are
turn on at the same time. If promisc had been off there was no way to turn
off allmulti mode.
The patch corrects this behavior. Switching allmulti does not depends on
promisc state mode anymore
Fixes: f42a5c74da ("i40e: Add allmulti support for the VF")
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In iavf_configure_clsflower() the function will bail out if it is unable
to obtain the crit_section lock in a reasonable time. However, it will
clear the lock when exiting, so fix this.
Fixes: 640a8af584 ("i40evf: Reorder configure_clsflower to avoid deadlock on error")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf_free_queues() clears adapter->num_active_queues, which
iavf_free_q_vectors() relies on, so swap the order of these two function
calls in iavf_disable_vf(). This resolves a panic encountered when the
interface is disabled and then later brought up again after PF
communication is restored.
Fixes: 65c7006f23 ("i40evf: assign num_active_queues inside i40evf_alloc_queues")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the driver has lost contact with the PF then it enters a disabled state
and frees adapter->vf_res. However, ndo_fix_features can still be called on
the interface, so we need to check for this condition first. Since we have
no information on the features at this time simply leave them unmodified
and return.
Fixes: c4445aedfe ("i40evf: Fix VLAN features")
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixed return correct code from set the new channel count.
Implemented by check if reset is done in appropriate time.
This solution give a extra time to pf for reset vf in case
when user want set new channel count for all vfs.
Without this patch it is possible to return misleading output
code to user and vf reset not to be correctly performed by pf.
Fixes: 5520deb153 ("iavf: Enable support for up to 16 queues")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a VF is removed and/or reset its Tx queues need to be
stopped from the PF. This is done by calling the ice_dis_vf_qs()
function, which calls ice_vsi_stop_lan_tx_rings(). Currently
ice_dis_vf_qs() is protected by the VF state bit ICE_VF_STATE_QS_ENA.
Unfortunately, this is causing the Tx queues to not be disabled in some
cases and when the VF tries to re-enable/reconfigure its Tx queues over
virtchnl the op is failing. This is because a VF can be reset and/or
removed before the ICE_VF_STATE_QS_ENA bit is set, but the Tx queues
were already configured via ice_vsi_cfg_single_txq() in the
VIRTCHNL_OP_CONFIG_VSI_QUEUES op. However, the ICE_VF_STATE_QS_ENA bit
is set on a successful VIRTCHNL_OP_ENABLE_QUEUES, which will always
happen after the VIRTCHNL_OP_CONFIG_VSI_QUEUES op.
This was causing the following error message when loading the ice
driver, creating VFs, and modifying VF trust in an endless loop:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by always calling ice_dis_vf_qs() and silencing the error
message in ice_vsi_stop_tx_ring() since the calling code ignores the
return anyway. Also, all other places that call ice_vsi_stop_tx_ring()
catch the error, so this doesn't affect those flows since there was no
change to the values the function returns.
Other solutions were considered (i.e. tracking which VF queues had been
"started/configured" in VIRTCHNL_OP_CONFIG_VSI_QUEUES, but it seemed
more complicated than it was worth. This solution also brings in the
chance for other unexpected conditions due to invalid state bit checks.
So, the proposed solution seemed like the best option since there is no
harm in failing to stop Tx queues that were never started.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VF was not able to change its hardware MAC address in case
the new address was already present in the MAC filter list.
Change the handling of VF add mac request to not return
if requested MAC address is already present on the list
and check if its hardware MAC needs to be updated in this case.
Fixes: ed4c068d46 ("ice: Enable ip link show on the PF to display VF unicast MAC(s)")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when a trusted VF enables promiscuous mode spoofchk will be
disabled. This is wrong and should only be modified from the
ndo_set_vf_spoofchk callback. Fix this by removing the call to toggle
spoofchk for trusted VFs.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a VF requests promiscuous mode and it's trusted and true promiscuous
mode is enabled the PF driver attempts to enable unicast and/or
multicast promiscuous mode filters based on the request. This is fine,
but there are a couple issues with the current code.
[1] The define to configure the unicast promiscuous mode mask also
includes bits to configure the multicast promiscuous mode mask, which
causes multicast to be set/cleared unintentionally.
[2] All 4 cases for enable/disable unicast/multicast mode are not
handled in the promiscuous mode message handler, which causes
unexpected results regarding the current promiscuous mode settings.
To fix [1] make sure any promiscuous mask defines include the correct
bits for each of the promiscuous modes.
To fix [2] make sure that all 4 cases are handled since there are 2 bits
(FLAG_VF_UNICAST_PROMISC and FLAG_VF_MULTICAST_PROMISC) that can be
either set or cleared. Also, since either unicast and/or multicast
promiscuous configuration can fail, introduce two separate error values
to handle each of these cases.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-29
This series contains updates to ice and iavf drivers and virtchnl header
file.
Brett removes vlan_promisc argument from a function call for ice driver.
In the virtchnl header file he removes an unused, reserved define and
converts raw value defines to instead use the BIT macro.
Marcin adds syncing of MAC addresses when creating switchdev VFs to
remove error messages on link up and stops showing buffer information
for port representors to remove duplicated entries being displayed for
ice driver.
Karen introduces a helper to go from pci_dev to iavf_adapter in the
iavf driver.
Przemyslaw fixes an issue where iavf was attempting to free IRQs before
calling disable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-10-29
This series contains updates to igc driver only.
Sasha removes an unnecessary media type check, adds a new device ID, and
changes a device reset to a port reset command.
====================
Link: https://lore.kernel.org/r/20211029174101.2970935-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix driver not freeing VF's traffic irqs, prior to calling
pci_disable_msix in iavf_remove.
There were possible 2 erroneous states in which, iavf_close would
not be called.
One erroneous state is fixed by allowing netdev to register, when state
is already running. It was possible for VF adapter to enter state loop
from running to resetting, where iavf_open would subsequently fail.
If user would then unload driver/remove VF pci, iavf_close would not be
called, as the netdev was not registered, leaving traffic pcis still
allocated.
Fixed this by breaking loop, allowing netdev to open device when adapter
state is __IAVF_RUNNING and it is not explicitily downed.
Other possiblity is entering to iavf_remove from __IAVF_RESETTING state,
where iavf_close would not free irqs, but just return 0.
Fixed this by checking for last adapter state and then removing irqs.
Kernel panic:
[ 2773.628585] kernel BUG at drivers/pci/msi.c:375!
...
[ 2773.631567] RIP: 0010:free_msi_irqs+0x180/0x1b0
...
[ 2773.640939] Call Trace:
[ 2773.641572] pci_disable_msix+0xf7/0x120
[ 2773.642224] iavf_reset_interrupt_capability.part.41+0x15/0x30 [iavf]
[ 2773.642897] iavf_remove+0x12e/0x500 [iavf]
[ 2773.643578] pci_device_remove+0x3b/0xc0
[ 2773.644266] device_release_driver_internal+0x103/0x1f0
[ 2773.644948] pci_stop_bus_device+0x69/0x90
[ 2773.645576] pci_stop_and_remove_bus_device+0xe/0x20
[ 2773.646215] pci_iov_remove_virtfn+0xba/0x120
[ 2773.646862] sriov_disable+0x2f/0xe0
[ 2773.647531] ice_free_vfs+0x2f8/0x350 [ice]
[ 2773.648207] ice_sriov_configure+0x94/0x960 [ice]
[ 2773.648883] ? _kstrtoull+0x3b/0x90
[ 2773.649560] sriov_numvfs_store+0x10a/0x190
[ 2773.650249] kernfs_fop_write+0x116/0x190
[ 2773.650948] vfs_write+0xa5/0x1a0
[ 2773.651651] ksys_write+0x4f/0xb0
[ 2773.652358] do_syscall_64+0x5b/0x1a0
[ 2773.653075] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 22ead37f8a ("i40evf: Add longer wait after remove module")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add helper function to go from pci_dev to adapter to make work simple -
to go from a pci_dev to the adapter structure and make netdev assignment
instead of having to go to the net_device then the adapter.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Disable showing bus-info information for port representors in switchdev
mode. This fixes a bug that caused displaying wrong netdev descriptions in
lshw tool - one port representor displayed PF branding string, and in turn
one PF displayed a "generic" description. The bug occurs when many devices
show the same bus-info in ethtool, which was the case in switchdev mode (PF
and its port representors displayed the same bus-info). The bug occurs only
if a port representor netdev appears before PF netdev in /proc/net/dev.
In the examples below:
ens6fX is PF
ens6fXvY is VF
ethX is port representor
One irrelevant column was removed from output
Before:
$ sudo lshw -c net -businfo
Bus info Device Description
=========================================
pci@0000:02:00.0 eth102 Ethernet Controller E810-XXV for SFP
pci@0000:02:00.1 ens6f1 Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0 ens6f0v0 Ethernet Adaptive Virtual Function
pci@0000:02:01.1 ens6f0v1 Ethernet Adaptive Virtual Function
pci@0000:02:01.2 ens6f0v2 Ethernet Adaptive Virtual Function
pci@0000:02:00.0 ens6f0 Ethernet interface
Notice that eth102 and ens6f0 have the same bus-info and their descriptions
are swapped.
After:
$ sudo lshw -c net -businfo
Bus info Device Description
=========================================
pci@0000:02:00.0 ens6f0 Ethernet Controller E810-XXV for SFP
pci@0000:02:00.1 ens6f1 Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0 ens6f0v0 Ethernet Adaptive Virtual Function
pci@0000:02:01.1 ens6f0v1 Ethernet Adaptive Virtual Function
pci@0000:02:01.2 ens6f0v2 Ethernet Adaptive Virtual Function
Fixes: 7aae80cef7 ("ice: add port representor ethtool ops and stats")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When spawning VFs in switchdev mode, internal filter list of VSIs is
cleared, which includes MAC rules. However MAC entries stay on netdev's
multicast list, which causes error message when bringing link up after
spawning VFs ("Failed to delete MAC filters"). __dev_mc_sync() is
called and tries to unsync addresses that were already removed
internally when adding VFs.
This can be reproduced with:
1) Load ice driver
2) Change PF to switchdev mode
3) Bring PF link up
4) Bring PF link down
5) Create a VF on PF
6) Bring PF link up
Added clearing of netdev's multicast (and also unicast) list when
spawning VFs in switchdev mode, so the state of internal rule list and
netdev's MAC list is consistent.
Fixes: 1a1c40df2e ("ice: set and release switchdev environment")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the vlan_promisc flag is used exclusively by VF VSI to
determine whether or not to toggle VLAN pruning along with
trusted/true-promiscuous mode. This is not needed for a couple of
reasons. First, trusted/true-promiscuous mode is only supposed to allow
all MAC filters within VLANs that a VF has added filters for, so VLAN
pruning should not be disabled. Second, the boolean argument makes the
function confusing and unintuitive. Remove this flag.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The _reset_hw_base method switched from port reset (CTRL[26]) to device
reset (CTRL[29]) since the FW was receiving an interrupt on CTRL[29].
FW code was later modified to also receive an interrupt on CTRL[26].
Since certain HW values are not reset to default by CTRL[29], we go back
to CTRL[26] for the HW reset, as it meets all current requirements.
This reverts commit bb4265ec24 ("igc: Update the MAC reset flow").
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new device ID for the next step of the silicon and
reflect the I226_LMVP part.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices only have copper phy media type. There is no point in
checking phy media type during the phy initialization. This patch cleans
up a pointless check.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The variable ret_val is being initialized with a value that is never
read, it is being updated later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.
The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).
The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.
The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.
The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.
The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.
Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following coccicheck warning:
./drivers/net/ethernet/intel/i40e/i40e_xsk.c:229:35-40: WARNING:
conversion to bool not needed here
./drivers/net/ethernet/intel/ice/ice_xsk.c:399:35-40: WARNING:
conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-28
This series contains updates to ice driver only.
Michal adds support for eswitch drop and redirect filters from and to
tunnel devices. From meaning from uplink to VF and to means from VF to
uplink. This is accomplished by adding support for indirect TC tunnel
notifications and adding appropriate training packets and match fields
for UDP tunnel headers. He also adds returning virtchannel responses for
blocked operations as returning a response is still needed.
Marcin sets netdev min and max MTU values on port representors to allow
for MTU changes over default values.
Brett adds detecting and reporting of PHY firmware load issues for devices
which support this.
Nathan Chancellor fixes a clang warning for implicit fallthrough.
Wang Hai fixes a return value for failed allocation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Return error code if devm_kmemdup() fails in ice_get_recp_frm_fw()
Fixes: fd2a6b71e3 ("ice: create advanced switch recipe")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clang warns:
drivers/net/ethernet/intel/ice/ice_lib.c:1906:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
default:
^
drivers/net/ethernet/intel/ice/ice_lib.c:1906:2: note: insert 'break;' to avoid fall-through
default:
^
break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/1482
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some devices have support for loading the PHY FW and in some cases this
can fail. When this fails, the FW will set the corresponding bit in the
link info structure. Also, the FW will send a link event if the correct
link event mask bit is set. Add support for printing an error message
when the PHY FW load fails during any link configuration flow and the
link event flow.
Since ice_check_module_power() is already doing something very similar
add a new function ice_check_link_cfg_err() so any failures reported in
the link info's link_cfg_err member can be printed in this one function.
Also, add the new ICE_FLAG_PHY_FW_LOAD_FAILED bit to the PF's flags so
we don't constantly print this error message during link polling if the
value never changed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This change adds support for changing MTU on port representor in
switchdev mode, by setting the min/max MTU values on port representor
netdev. Before it was possible to change the MTU only in a limited,
default range (68-1500).
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
