Commit Graph

221 Commits

Author SHA1 Message Date
Richard Tresidder 3345d47023 iio: magnetometer: mag3110: Add ability to run in continuous mode
Adds the ability to run the Mag3110 in continuous mode to speed up the
sampling rate.
Depending on the sampling rate requested the device can be put in or out
of continuous mode automatically.
Shifting out of continuous mode requires a potential 1 / ODR wait which
is also implemented.
Modified the sleep method when data is not ready to allow for
sampling > 50sps to work.

Signed-off-by: Richard Tresidder <rtresidd@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-12 11:01:59 +01:00
Rodrigo Siqueira 5def839c48 iio:magnetometer: Replace magic number 0 by IIO_CHAN_INFO_RAW
The function magn_3d_read_raw has a switch statement handling multiple
cases per channel. The first case statement uses the magic number 0,
which means IIO_CHAN_INFO_RAW. Additionally, the iio_chan_spec for
magn_3d_channels is configured to be IIO_CHAN_INFO_RAW. Therefore, this
patch replaces the magic number 0 for the appropriate IIO_CHAN_INFO_RAW.

Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-03-03 15:23:13 +00:00
Andy Shevchenko 9ed2484598 iio: magnetometer: ak8975: Add another ACPI ID
Add new ACPI ID for ak9911 as had been found on prototype board.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-12-02 10:40:02 +00:00
Linus Torvalds 449fcf3ab0 Staging/IIO patches for 4.15-rc1
Here is the "big" staging and IIO driver update for 4.15-rc1.
 
 Lots and lots of little changes, almost all minor code cleanups as the
 Outreachy application process happened during this development cycle.
 Also happened was a lot of IIO driver activity, and the typec USB code
 moving out of staging to drivers/usb (same commits are in the USB tree
 on a persistent branch to not cause merge issues.)
 
 Overall, it's a wash, I think we added a few hundred more lines than
 removed, but really only a few thousand were modified at all.
 
 All of these have been in linux-next for a while.  There might be a
 merge issue with Al's vfs tree in the pi433 driver (take his changes,
 they are always better), and the media tree with some of the odd atomisp
 cleanups (take the media tree's version).
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
 g3ioPBqmqC/2DSbldr2o
 =/ebw
 -----END PGP SIGNATURE-----

Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging and IIO updates from Greg KH:
 "Here is the "big" staging and IIO driver update for 4.15-rc1.

  Lots and lots of little changes, almost all minor code cleanups as the
  Outreachy application process happened during this development cycle.
  Also happened was a lot of IIO driver activity, and the typec USB code
  moving out of staging to drivers/usb (same commits are in the USB tree
  on a persistent branch to not cause merge issues.)

  Overall, it's a wash, I think we added a few hundred more lines than
  removed, but really only a few thousand were modified at all.

  All of these have been in linux-next for a while. There might be a
  merge issue with Al's vfs tree in the pi433 driver (take his changes,
  they are always better), and the media tree with some of the odd
  atomisp cleanups (take the media tree's version)"

* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
  staging: lustre: add SPDX identifiers to all lustre files
  staging: greybus: Remove redundant license text
  staging: greybus: add SPDX identifiers to all greybus driver files
  staging: ccree: simplify ioread/iowrite
  staging: ccree: simplify registers access
  staging: ccree: simplify error handling logic
  staging: ccree: remove dead code
  staging: ccree: handle limiting of DMA masks
  staging: ccree: copy IV to DMAable memory
  staging: fbtft: remove redundant initialization of buf
  staging: sm750fb: Fix parameter mistake in poke32
  staging: wilc1000: Fix bssid buffer offset in Txq
  staging: fbtft: fb_ssd1331: fix mirrored display
  staging: android: Fix checkpatch.pl error
  staging: greybus: loopback: convert loopback to use generic async operations
  staging: greybus: operation: add private data with get/set accessors
  staging: greybus: loopback: Fix iteration count on async path
  staging: greybus: loopback: Hold per-connection mutex across operations
  staging: greybus/loopback: use ktime_get() for time intervals
  staging: fsl-dpaa2/eth: Extra headroom in RX buffers
  ...
2017-11-13 20:53:28 -08:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Lorenzo Bianconi 9915c19056 iio: magnetometer: st_magn: add SPI-3wire support to LIS3MDL
Add SPI Serial Interface Mode (SIM) register information to
LIS3MDL magn sensor

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-10 20:36:33 +01:00
Lorenzo Bianconi 75d4c6d2e1 iio: st_sensors: decouple irq1 configuration parameters from the irq2 ones
Separate data-ready configuration parameters for INT1 and INT2 pins in
st_sensor_data_ready_irq data structure. That change will be use to
properly support LIS2DW12 accel sensor.

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-09 21:04:22 +01:00
Lorenzo Bianconi e72a060151 iio: st_sensors: add register mask for status register
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.

Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-10-09 21:01:45 +01:00
Greg Kroah-Hartman 1236d6bb6e Merge 4.14-rc4 into staging-next
We want the staging/iio fixes in here as well to handle merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-09 09:02:35 +02:00
Greg Kroah-Hartman 069f0e0c06 Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
 in IIO and the feeling is no one will care.
 
 A large part of this series is a boiler plate removal series avoiding
 the need to explicitly provide THIS_MODULE in various locations.
 It's very dull but touches all drivers.
 
 New device support
 * ad5446
   - add ids to support compatible parts DAC081S101, DAC101S101,
     DAC121S101.
   - add the dac7512 id and drop the misc driver as feeling is no
     one is using it (was introduced for a board that is long obsolete)
 * mt6577
   - add bindings for mt2712 which is fully compatible with other
     supported parts.
 * st_pressure
   - add support for LPS33HW and LPS35HW with bindings (ids mostly).
 
 New features
 * ccs811
   - Add support for the data ready trigger.
 * mma8452
   - remove artifical restriction on supporting multiple event types
     at the same time.
 * tcs3472
   - support out of threshold events
 
 Core and tree wide cleanup
 * Use macro magic to remove the need to provide THIS_MODULE as part of
   struct iio_info or struct iio_trigger_ops.  This is similar to
   work done in a number of other subsystems (e.g. i2c, spi).
 
   All drivers are fixed and then the fields in these structures are
   removed.
 
   This will cause build failures for out of tree drivers and any
   new drivers that cross with this work going into the kernel.
 
   Note mostly done with a coccinelle patch, included in the series
   on the mailing list but not merged as the fields no longer exist
   in the structures so the any hold outs will cause a build failure.
 
 Cleanups
 * ads1015
   - avoid writing config register when it doesn't change.
   - add 10% to conversion wait time as it seems it is sometimes
     a little small.
 * ade7753
   - replace use of core mlock with a local lock.  This is part of a
     long term effort to make the use of mlock opaque and single
     purpose.
 * ade7759
   - expand the use of buf_lock to cover previous mlock cases.  This
     is a slightly nicer solution to the same issue as in ade7753.
 * cros_ec
   - drop an unused variable
 * inv_mpu6050
   - add a missing break in a switch for consistency - not actual
     bug,
   - make some local arrays static to save on object code size.
 * max5481
   - drop manual setting of the spi module owner as handled by the
     spi core.
 * max5487
   - drop manual setting of the spi module owner as handled by the
     spi core.
 * max9611
   - drop explicit setting of the i2c module owner as handled by
     the i2c core.
 * mcp320x
   - speed up reads on single channel devices,
   - drop unused of_device_id data elements,
   - document the struct mcp320x,
   - improve binding docs to reflect restrictions on spi setup and
     to make it explicit that the reference regulator is needed.
 * mma8452
   - symbolic to octal permissions,
   - unsigned to unsigned int.
 * st_lsm6dsx
   - avoid setting odr values multiple times,
   - drop config of LIR as it is only ever set to the existing
     defaults,
   - drop rounding configuration as it only ever matches the defaults.
 * ti-ads8688
   - drop manual setting of the spi module owner as handled by the
     spi core.
 * tsl2x7x
   - constify the i2c_device_id,
   - cleanup limit checks to avoid static checker warnings (and generally
     have nicer code).
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlnH4XkRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0Fogkaw//e3z+4TQT2Hn+550lBYUV8pBR5emDiSe3
 0QTG+ZS7Kh+fPYENLCXtW9ttZicmUSqkTQFvlMTjAxHyj9XzL7+BXS9UlNgVLsqX
 pn9KprPj31lrXpJOXMSgcdiqWMZLtCvprAJgnwfZt1GevS3WbCMmnnoaBuJV61jp
 w0VD+forukTGF7b0OMGB0d5mwtYS0bJYqXRRMPD+2bNeM4hqt5YM3+wHSqP35t3l
 MoaqKlbx7ZtKDF4zIa59nKNP7Ky7IByWogLZRlJ/vD/uKrACckPT22+KT8rX2TwA
 NpZb1Oy/KZBTl5D9iRjZADq4NaRJENFXJiG6GkjoGjrQhUqHaCinHWpLioqLGlRq
 qCPL2nRjqm4Qr7E8sxlwR1Ajlg0utBMY7Oflym/XJMMLF/ZE6HSrzyrxuVMG2EjV
 T7SVIncbfg6kyr/r4kKsAT3BUMV+TdO4sXm+JgphZBUqZLp0nFHnmjP7Rm2j2uWq
 +yLrSuF25RijrRj3sp28zg9dFWlRwRvZvcAx8kEGm1kMjMWr+Q10xTK9o/5LlFEw
 57sUm6qgmigPK8sahDtcdLIwaCPVvAYvJ0e4Mfw5UsPSlZmHmM1mLwjpwiXBZ5ig
 oxnJmTXsn5RcOGiW/mg0VCH26NkBx7H0fsRqQeq9wkxHLrm75vXroIn7YqRIg+Ad
 /Itu6x6fOIg=
 =ik5C
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Round one of new device support, features and cleanup for IIO in the 4.15 cycle.

Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.

A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.

New device support
* ad5446
  - add ids to support compatible parts DAC081S101, DAC101S101,
    DAC121S101.
  - add the dac7512 id and drop the misc driver as feeling is no
    one is using it (was introduced for a board that is long obsolete)
* mt6577
  - add bindings for mt2712 which is fully compatible with other
    supported parts.
* st_pressure
  - add support for LPS33HW and LPS35HW with bindings (ids mostly).

New features
* ccs811
  - Add support for the data ready trigger.
* mma8452
  - remove artifical restriction on supporting multiple event types
    at the same time.
* tcs3472
  - support out of threshold events

Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
  struct iio_info or struct iio_trigger_ops.  This is similar to
  work done in a number of other subsystems (e.g. i2c, spi).

  All drivers are fixed and then the fields in these structures are
  removed.

  This will cause build failures for out of tree drivers and any
  new drivers that cross with this work going into the kernel.

  Note mostly done with a coccinelle patch, included in the series
  on the mailing list but not merged as the fields no longer exist
  in the structures so the any hold outs will cause a build failure.

Cleanups
* ads1015
  - avoid writing config register when it doesn't change.
  - add 10% to conversion wait time as it seems it is sometimes
    a little small.
* ade7753
  - replace use of core mlock with a local lock.  This is part of a
    long term effort to make the use of mlock opaque and single
    purpose.
* ade7759
  - expand the use of buf_lock to cover previous mlock cases.  This
    is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
  - drop an unused variable
* inv_mpu6050
  - add a missing break in a switch for consistency - not actual
    bug,
  - make some local arrays static to save on object code size.
* max5481
  - drop manual setting of the spi module owner as handled by the
    spi core.
* max5487
  - drop manual setting of the spi module owner as handled by the
    spi core.
* max9611
  - drop explicit setting of the i2c module owner as handled by
    the i2c core.
* mcp320x
  - speed up reads on single channel devices,
  - drop unused of_device_id data elements,
  - document the struct mcp320x,
  - improve binding docs to reflect restrictions on spi setup and
    to make it explicit that the reference regulator is needed.
* mma8452
  - symbolic to octal permissions,
  - unsigned to unsigned int.
* st_lsm6dsx
  - avoid setting odr values multiple times,
  - drop config of LIR as it is only ever set to the existing
    defaults,
  - drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
  - drop manual setting of the spi module owner as handled by the
    spi core.
* tsl2x7x
  - constify the i2c_device_id,
  - cleanup limit checks to avoid static checker warnings (and generally
    have nicer code).
2017-09-25 12:56:37 +02:00
Greg Kroah-Hartman b2e312061c First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window.  As such the tree
 is based on top of a prior staging/staging-next tree.
 
 * iio core
   - return and error for a failed read_reg debugfs call rather than
     eating the error.
 * ad7192
   - Use the dedicated reset function in the ad_sigma_delta library
     instead of an spi transfer with the data on the stack which
     could cause problems with DMA.
 * ad7793
   - Implement a dedicate reset function in the ad_sigma_delta library
     and use it to correctly reset this part.
 * bme280
   - ctrl_reg write must occur after any register writes
   for updates to take effect.
 * mcp320x
   - negative voltage readout was broken.
   - Fix an oops on module unload due to spi_set_drvdata not being called
     in probe.
 * st_magn
   - Fix the data ready line configuration for the lis3mdl. It is not
     configurable so the st_magn core was assuming it didn't exist
     and so wasn't consuming interrupts resulting in an unhandled
     interrupt.
 * stm32-adc
   - off by one error on max channels checking.
 * stm32-timer
   - preset should not be buffered - reorganising register writes avoids
   this.
   - fix a corner case in which write preset goes wrong when a timer is
   used first as a trigger then as a counter with preset. Odd case but
   you never know.
 * ti-ads1015
   - Fix setting of comparator polarity by fixing bitfield definition.
 * twl4030
   - Error path handling fix to cleanup in event of regulator
     registration failure.
   - Disable the vusb3v1 regulator correctly in error handling
   - Don't paper over a regulator enable failure.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlnH2PkRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0FoiNFw//XKT/CRq7R8Dg5vy4FT7NRw/SpSVH9u8M
 JsIISyAoh0jfOFJFkVv2Ll+Zs+SkbXJOPMUreaFJMnftSCkBdteT9D5kz5cYiUkO
 sFn58YEEqKCqQVJBEi0yM00HMxbpNKiNHXzo9WC8ZiUVRJqSigq1coznSqaZngRd
 yf4a9Z33jiH/NXalqy5Vb4CSn76UWpvvYJ11tuNxXqOldkyU4sm8bvsPWnBg1qG3
 YIuVZs83Rv1HW0t6ktYf3WwC2rBhKEM8st2fUCLkU+4+foDuqQBiFdWJzTcxe6Ru
 8za+q3ngOo7rRkLS8cSTsh8hbfKwIV0e3rQvsN3zqodqjPilw9uH3eybMYzLK/0I
 j9o12jaD1Ow7zQfiQnNnyJqDLddEt+f6GcrI/iYQPlTIQIhqDii4YInDyCrF4xbr
 i/8saOr5n4PsdHRovTUl2rrgiX+Jix6OmNLEtUdp1HWrc0XwbZ5L/1g6pXFL98QZ
 Kq8MwjNu+6x+66Hga/1fll19hZ/VMYGqxFtoP+6S28TS1bO9dXm6XNl5/U5Nh5mN
 J255UFCdFkBmJO9nP7tmbDscMCAbhc6AOHKxjUebuoNnyhyV+20W9S/gpzTIilnO
 Gv9D0z29zITc8Hpfhl2YKC6F00BuRAdPFJo05rSE/KoWX3bkPCiXFTfQ+aPwB72h
 bYT4oJeUoQg=
 =CcjQ
 -----END PGP SIGNATURE-----

Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First round of IIO fixes for the 4.14 cycle

Note this includes fixes from recent merge window.  As such the tree
is based on top of a prior staging/staging-next tree.

* iio core
  - return and error for a failed read_reg debugfs call rather than
    eating the error.
* ad7192
  - Use the dedicated reset function in the ad_sigma_delta library
    instead of an spi transfer with the data on the stack which
    could cause problems with DMA.
* ad7793
  - Implement a dedicate reset function in the ad_sigma_delta library
    and use it to correctly reset this part.
* bme280
  - ctrl_reg write must occur after any register writes
  for updates to take effect.
* mcp320x
  - negative voltage readout was broken.
  - Fix an oops on module unload due to spi_set_drvdata not being called
    in probe.
* st_magn
  - Fix the data ready line configuration for the lis3mdl. It is not
    configurable so the st_magn core was assuming it didn't exist
    and so wasn't consuming interrupts resulting in an unhandled
    interrupt.
* stm32-adc
  - off by one error on max channels checking.
* stm32-timer
  - preset should not be buffered - reorganising register writes avoids
  this.
  - fix a corner case in which write preset goes wrong when a timer is
  used first as a trigger then as a counter with preset. Odd case but
  you never know.
* ti-ads1015
  - Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
  - Error path handling fix to cleanup in event of regulator
    registration failure.
  - Disable the vusb3v1 regulator correctly in error handling
  - Don't paper over a regulator enable failure.
2017-09-25 10:58:22 +02:00
Lorenzo Bianconi c65e3d6ef4 iio: magnetometer: st_magn: fix drdy line configuration for LIS3MDL
Data-ready line in LIS3MDL is routed to drdy pin and it is not possible
to select a different INT pin. st_sensors_set_dataready_irq() assumes
that if drdy int address is not exported in register map, irq trigger
is not supported by the sensor and hw_irq_trigger is always false.
Based on this configuration st_sensors_irq_thread does not consume
generated interrupt causing an unhandled irq.
Fix this taking into account status register address in
st_sensors_set_dataready_irq()

Fixes: 90efe05562 (iio: st_sensors: harden interrupt handling)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-09-03 17:39:39 +01:00
Greg Kroah-Hartman 8439a69e72 Merge 4.13-rc7 into staging-next
We want the staging and iio fixes in here to handle the merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28 15:26:48 +02:00
Jonathan Cameron 7f307262af iio:magnetometer: drop assign iio_info.driver_module and iio_trigger_ops.owner
The equivalent of both of these are now done via macro magic when
the relevant register calls are made.  The actual structure
elements will shortly go away.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
2017-08-22 21:32:52 +01:00
Michał Mirosław 0a60340f19 iio: magnetometer: ak8974: debug AMI306 calibration data
Use AMI306 calibration data for randomness and debugging.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20 15:41:11 +01:00
Lorenzo Bianconi 8b35a5f87a iio: magnetometer: st_magn: remove ihl property for LSM303AGR
Remove IRQ active low support for LSM303AGR since the sensor does not
support that capability for data-ready line

Fixes: a9fd053b56 (iio: st_sensors: support active-low interrupts)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20 15:21:49 +01:00
Lorenzo Bianconi 541ee9b24f iio: magnetometer: st_magn: fix status register address for LSM303AGR
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20 15:21:48 +01:00
Michał Mirosław 9991f99eed iio: magnetometer: ak8974: mark INT_CLEAR as precious
Reading INT_CLEAR has side effects - disallow reading it via debugfs.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20 15:17:39 +01:00
Michał Mirosław 408cc6eb1e iio: magnetometer: ak8974: add_device_randomness (serial number)
Mix device-specific data into randomness pool.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20 15:17:27 +01:00
Michał Mirosław 21be26fc67 iio: magnetometer: ak8974: support AMI306 variant
Add support for AMI306 magnetometer - very similar to AMI305.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-20 11:18:33 +01:00
Lorenzo Bianconi d0b7fea58a iio: magnetometer: add support to LIS2MDL
add support to STMicroelectronics LIS2MDL magnetometer in
st_magn framework

http://www.st.com/resource/en/datasheet/lis2mdl.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2017-08-17 15:51:39 +01:00
Lorenzo Bianconi 65a687a22d iio: magnetometer: st_magn_spi: add OF capability to st_magn_spi
Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-02 10:24:55 +01:00
Matthias Kaehlcke 2aac3388f1 iio: magnetometer: Only declare ACPI table when ACPI is enable
Don't inflate the kernel size with data that isn't used. The conditional
declaration also fixes the following warning when building with clang:

drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match'
  is not needed and will not be emitted
  [-Werror,-Wunneeded-internal-declaration]

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-02 10:24:54 +01:00
Lorenzo Bianconi 250bbbdbed iio: common: st_sensors: move st_sensors_of_i2c_probe() in common code
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-01 10:16:56 +01:00
Lorenzo Bianconi 1371856416 iio: magnetometer: st_magn_core: enable multiread by default for LIS3MDL
Enable multiread by default for LIS3MDL since using I2C interface
the subaddr Msb is used to automatically increase the slave address
during multiple data read/write. In the same way, using SPI interface,
bit 1 in register address is used to enable auto-increment of the slave
address in multiple read/write.

Fixes: 872e79add7 (iio:magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-07-01 10:16:52 +01:00
Lorenzo Bianconi c83761ff0a iio: magnetometer: st_magn_spi: fix spi_device_id table
Remove LSM303DLHC, LSM303DLM from st_magn_id_table since LSM303DL series
does not support spi interface

Fixes: 872e79add7 (iio: magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-06-11 15:07:40 +01:00
Greg Kroah-Hartman 1c816bad41 Merge 4.11-rc4 into staging-next
We need the IIO fixes in here as well to handle merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-27 09:11:25 +02:00
Javier Martinez Canillas ee9a90735b iio: magnetometer: mag3110: Add OF device ID table
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.

But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-03-19 10:57:24 +00:00
Javier Martinez Canillas 49926b1216 iio: magnetometer: bmc150_magn_i2c: Add OF device ID table
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.

But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-03-19 10:50:10 +00:00
Dmitry Torokhov 3ff861f59f iio: magnetometer: ak8974: remove incorrect __exit markups
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-03-05 13:52:01 +00:00
Alison Schofield 80dea21f95 iio: magnetometer: mag3110: claim direct mode during raw writes
Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during raw writes.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-21 12:20:40 +00:00
Colin Ian King e2eb179c00 iio: magnetometer: ak8974: remove redundant zero timeout check
At the end of the delay loop timeout will always be zero
and hence the check for !timeout will always be true. Remove
the redundant check and the redundant return 0 at the end of
the function.

Fixes CoverityScan CID#1357168 ("Logically dead code")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2017-01-14 13:10:04 +00:00
Ooi, Joyce 6f771d0b33 iio: magnetometer: separate the values of attributes based on their usage type for HID compass sensor
There are 2 usage types (Magnetic Flux and Heading data field) for HID
compass sensor, thus the values of offset, scale, and sensitivity should
be separated according to their respective usage type. The changes made
are as below:
1. Hysteresis: A struct hid_sensor_common rot_attributes is created in
struct magn_3d_state to contain the sensitivity for IIO_ROT.
2. Scale: scale_pre_decml and scale_post_decml are separated for IIO_MAGN
and IIO_ROT.
3. Offset: Same as scale, value_offset is separated for IIO_MAGN and
IIO_ROT.

For sensitivity, HID_USAGE_SENSOR_ORIENT_MAGN_FLUX and
HID_USAGE_SENSOR_ORIENT_MAGN_HEADING are used for sensivitity fields based
on the HID Sensor Usages specifications. Hence, these changes are added on
the sensitivity field.

Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-11-24 20:41:30 +00:00
Linus Walleij 57d0355451 iio: magn: st_magn: inline per-sensor data
We have #defines for all the individual sensor registers and
value/mask pairs #defined at the top of the file and used at
exactly one spot.

This is usually good if the #defines give a meaning to the
opaque magic numbers.

However in this case, the semantic meaning is inherent in the
name of the C99-addressable fields, and that means duplication
of information, and only makes the code hard to maintain since
you every time have to add a new #define AND update the site
where it is to be used.

Get rid of the #defines and just open code the values into the
appropriate struct elements. Make sure to explicitly address
the .hz and .value fields in the st_sensor_odr_avl struct
so that the meaning of all values is clear.

This patch is purely syntactic should have no semantic effect.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-11-12 15:45:37 +00:00
Ico Doornekamp 7f709dcda4 iio: magnetometer: ak8974: small endianness fixes
Fixes two cases of 'cast to restricted __le16' as reported by sparse.

Signed-off-by: Ico Doornekamp <ico@pruts.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-10-03 21:30:00 +01:00
Sandhya Bankar 69c72ec9c8 drivers: iio: magnetometer: Fix sparse endianness warnings cast to restricted __be16
Fix the following sparse endianness warnings:

drivers/iio/magnetometer/ak8975.c:716:16: warning: cast to restricted __le16
drivers/iio/magnetometer/ak8975.c:837:19: warning: cast to restricted __le16
drivers/iio/magnetometer/ak8975.c:838:19: warning: cast to restricted __le16
drivers/iio/magnetometer/ak8975.c:839:19: warning: cast to restricted __le16

Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-09-27 21:08:45 +01:00
Wei Yongjun 96303e2027 iio: magn: ak8974: remove .owner field for driver
Remove .owner field if calls are used which set it automatically.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-08-29 20:12:10 +01:00
Arnd Bergmann 5bc55ef31f iio: magn/ak8974: avoid unused function warning
The ak8974_configure() function is used only from the PM code,
but that can be hidden when CONFIG_PM is disabled:

drivers/iio/magnetometer/ak8974.c:201:12: error: 'ak8974_configure' defined but not used [-Werror=unused-function]

This replaces the #ifdef with a __maybe_unused annotation, which
will work correctly in all configurations and avoid the warning,
as the compiler can now see where ak8974_configure is called from.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7c94a8b2ee ("iio: magn: add a driver for AK8974")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-08-29 19:54:55 +01:00
Alison Schofield 197399dcd7 iio: magnetometer: mag3110: claim direct mode during raw reads
Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-08-21 19:37:35 +01:00
Linus Walleij 7c94a8b2ee iio: magn: add a driver for AK8974
This adds a driver for the Asahi Kasei AK8974 and its sibling
AMI305 magnetometers. It was deployed on scale in 2009 on a
multitude of devices. It is distincly different from AK8973
and AK8975 and needs its own driver.

This patch is based on the long lost work of Samu Onkalo at Nokia,
who made a misc character device driver for the Maemo/MeeGo Nokia
devices, before the time of the IIO subsystem. It was mounted in e.g.
the Nokia N950, N8, N86, N97 etc. It is also mounted on the
ST-Ericsson HREF reference designs.

It works nicely in sysfs:

$ cat in_magn_x_raw && cat in_magn_y_raw && cat in_magn_z_raw
-55
-101
161

And with buffered reads using a simple HRTimer trigger:
$ generic_buffer -c10 -a -n ak8974 -t foo
iio device number being used is 3
iio trigger number being used is 2
No channels are enabled, enabling all channels
Enabling: in_magn_x_en
Enabling: in_magn_y_en
Enabling: in_magn_z_en
Enabling: in_timestamp_en
/sys/bus/iio/devices/iio:device3 foo
-58.000000 -102.000000 157.000000 946684970985321044
-60.000000 -98.000000 159.000000 946684971012237548
-60.000000 -106.000000 163.000000 946684971032257080
-62.000000 -94.000000 169.000000 946684971052185058
-58.000000 -98.000000 163.000000 946684971072204589
-54.000000 -100.000000 163.000000 946684971092224121
-53.000000 -103.000000 164.000000 946684971112731933
-50.000000 -102.000000 165.000000 946684971132232666
-61.000000 -101.000000 164.000000 946684971152191162
-57.000000 -99.000000 168.000000 946684971172210693
Disabling: in_magn_x_en
Disabling: in_magn_y_en
Disabling: in_magn_z_en
Disabling: in_timestamp_en

I cannot currently scale these raw values to gauss. This is
because of lack of documentation. I have sent a request for
a datasheet to Asahi Kasei.

The driver can optionally use a DRDY line IRQ to capture data,
else it will sleep and poll.

Cc: Samu Onkalo <samu.onkalo@intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-08-15 16:49:39 +01:00
Linus Walleij cde4cb5dd4 iio: magn: ak8975: deploy runtime and system PM
This adds runtime PM support to the AK8975 driver. It solves two
problems:

- After reading the first value the chip was left in MODE_ONCE,
  meaning (presumably) it may be consuming more power. Now the
  runtime PM hooks kick in and set it to POWER_DOWN.

- Regulators were simply enabled and left on, making it
  impossible to turn the power consuming regulators off because
  of the increased refcount. We now disable the regulators at
  autosuspend.

- We also handle system suspend: by using pm_runtime_force_suspend()
  and pm_runtime_force_resume() from the system PM sleep hooks,
  the runtime PM code is managing the power also for this case.
  It is currently not completely optimal: when the system resumes
  the AK8975 goes into active mode even if noone is going to use
  it: currently the force calls need to be paired, but the runtime
  PM people are working on making it possible to leave devices
  runtime suspended when coming back from sleep.

Inspired by my work on the BH1780 light sensor driver.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 20:40:16 +01:00
Linus Walleij 8d06cd25f7 iio: magn: ak8975: make sure to power down at remove()
The code was not powering the magnetometer down properly at
remove(): just cutting the regulators without first setting the
device in power off mode. Fix this.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 20:40:12 +01:00
Linus Walleij b1037c1a49 iio: magn: ak8975: allow a delay after enabling regulators
The datasheet actually specifies that we need to wait atleast
500us after powering on the device before trying to set mode.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 20:40:04 +01:00
Linus Walleij 9e6c16d989 iio: magn: ak8975: refactor regulator handlers
Move the regulator_get() calls directly into the probe() function,
keep only the power_on()/power_off() functions to flick the
regulators on/off.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 20:39:58 +01:00
Linus Walleij b21d3f3452 iio: magn: ak8975: add Vid regulator
The AK8975 has two power sources: Vdd (analog voltage supply)
and Vid (digital voltage supply). Optionally also obtain the Vid
supply regulator and enable it.

If an error occurs when enabling one of the regulators: bail out.

Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Richard Leitner <dev@g0hl1n.net>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 20:39:51 +01:00
Linus Walleij 90e96fdd01 iio: magn: ak8975: fix regulator usage
IS_ERR_OR_NULL() should never be used with regulators because
a NULL pointer may be a perfectly valid dummy regulator

We should always succeed to fetch and enable a regulator, but
it may be a dummy. That is fine, so bail out for any real
errors or probe deferrals

Include the error code in the warning print so we know what
kind of problem we're dealing with (for example it is nice to
see if it is a probe deferral).

As we will bail out of probe if the regulator is erroneous,
just issue regulator_disable() on the poweroff path: it will
succeed.

Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 20:39:43 +01:00
Gregor Boirie bc2b7dab62 iio:core: timestamping clock selection support
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.

Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.

Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2016-06-30 19:41:38 +01:00
Greg Kroah-Hartman af52739b92 Merge 4.7-rc4 into staging-next
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-20 08:25:44 -07:00
Greg Kroah-Hartman aabb406008 First round of IIO new device support, features and cleanups for the 4.8 cycle.
New device support
 * ads1015
   - add ads1115 support
 * bma220 accelerometer
   - new driver
   - triggered buffer support.
 * bmc150
   - add bmm150 support.
 * bmp280
   - bme280 support with addition of humidity channel.
 * max5487 potentiometer
   - new driver
 * MMA7660FC accelerometer.
   - New driver
 * st-pressure
   - support for the lps22hb
 * loop trigger.
   - This one is *nasty* but we have real applications (parrot drones) where
   it is useful.  The trigger basically spins as hard as it can firing off
   a new trigger each time all triggered devices come back to say they are
   done.  It doesn't hang a machine even when doing it on a dummy driver.
   A lot nicer than having this implemented within lots of device drivers
   anyway.
 
 Core stuff
 * Add support to create IIO devices via configfs (similar to we did for
 triggers a while back) + docs.
 * New channel types
   - IIO_ELECTRICAL_CONDUCTIVITY
 * Couple of MAINTAINERS patches to list the device tree bindings.
 * Make trigger ops structure non optional (comment fix). It hasn't been for
 an awful long time, but that's not what the description said.
 
 New features
 * ak8975
   - support adapters that are limited to byte data only by allowing the
   emulated block read i2c function that was recently introduced.
 * atlas-ph
   - support atlas-ec (electrical conductivity sensor)
 * bmi160
   - add available frequency and scale attributes to make the driver
   more user friendly (and avoid having to read the datasheet to know
   what will work).
 * dummy
   - move creation to configfs interface.  It's not real hardware so we
   are not that worried about the ABI breakage ;)
 * mma8452
   - oversampling ration support
 * nau7802
   - expose available gains to make life easier for userspace.
 * st-sensors
   - allow use of emulation for SMBus block reads as all the st parts support
   it.
 * ti-ads1015
   - list datasheet names to allow their use by inkernel consumers.
 * Various module alias additions to help auto probing.  Drop one redundant one
 as well.
 
 Cleanups
 * ad7266, ad7476, ad7887, ad7923, ad799x
   - use direct mode claim function rather than open coding it during sensor
   read (prevents switching on buffers mid read).
 * ad7793, ad7791
   - use direct mode claim to prevent frequency changes when buffers running.
 * afe440x - These are ABI breaking but the driver requires custom userspace
   code to do anything useful anyway and that is still being written and under
   control of TI.  Ultimately we may have other libraries to do pulse
   oximetry with these devices but we aren't aware of any yet.
   - kernel-doc format fixes
   - drop ifdef fun around of_match_ptr - it's not worth the mess to save
   a tiny amount of space.
   - drop some unnecessary register initializations.
   - drop the weird locked gain modes as they gain us nothing (can just set
   all gains separately).
   - remove handling of offset attributes seeing as no channels actually have
   them (oops)
   - Drop the LED3 input channel as it's an alias for ALED2.
   - *big one* remove channel names - an experiment that turned out to not
   make sense - see patch for details.
   - use regmap fields to clean up code.
   - tie the tia gain stages to appropriate channels in the ABI as that is
   what they really effect. Same with the LED currents.
   - cleanout some unused defines and fix a missnamed one.
 * atlas-ph
   - reorganise to allow support of other similar parts.
 * bmc150
   - document supported chips in kconfig help.
 * jsa1212
   - drop an unneeded i2c functionality check for functionality the driver
   doesn't use.
 * mxs-lradc
   - simply touch screen registration code.
   - remove the touch screen unregister as all devm based now.
   - disable only those channels that are masked in hardware stop (others
   are already dealt with elsewhere)
 * st-sensors
   - unexport st_sensors_get_buffer_element as nothing outside the st-sensors
   core driver uses it.
   - fix handling of failure to start up regulators.
 * tpl0102
   - drop an i2c functionality test for features that aren't needed.
 * ti-am335x
   - use variable name rather than type in sizeof for clarity.
   - use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
 
 Tools
 * Add install / uninstall to makefile.  Someone cares, so presumably
 some people will find it useful!
 *  generic_buffer
    - rename to iio_generic_buffer to line up with other tools.
    - handle cleanup when receiving signals
    - Add a --device-num option and a --trigger-num option rather than
    relying on naming which doesn't work if you have two of the same part.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXWFXGAAoJEFSFNJnE9BaIQ4kP/jcoVTR8w6EMdcr1BErrvFgm
 IMbMMK8wJtc1dhKcp77h/DQjCunPAaDMgdtg1uJcreRDl1dY1jiFh/PMLrt/eods
 tsJZcN1h40aLlPEdMQFl3oiaWjpUm23gdDtfiCHA+sM/FhQ+A+83EdonU7hbAGT2
 E2NAb5xkC+74WEUit5qEouz++4JRnsJEpBx3A7mwkiUH9RnFA9OflsTdIFSIEbzb
 V4yMWeYBAlhwKPy/7z6/hAMK/+Psabw8FppCAw2HcADVpT517rkl4MpvErSZeFGz
 cr46+ZWhXZ4PaG2jG2xVLpqSbqLSfWp8uqfj0WavW2gFn/1jCB+FST904q7IPVW2
 QPxALqxMAMSzOHxTYmDLfJ4IJ5vvLKroom4ixKgbl7jKXF3+PTooR6U4hGQmLK7K
 VKWjb/kIdHpuRT3/pG2kysMtJkk1av5BBZkl9sWUEFgCd4vYP1eB1Ah3aE/P26OH
 BCueMDaJqKAzmVa6Dx5MCLlJpxHpQl/OBz5wdXiMRbYeky/QHgzaTmi/HZ0wwXvn
 zFHAglWzLq7q0HY+q7wwI20R16cRYIve3HOaLFvQdXd1xpBP1BF+aAxT/vSb+otS
 1OWCEHAxq4XEM7VcRKv9XL59gXuSB8ZaSl6k82+IjjfgOqLHh8BSygVle7iu14TE
 glokfXQRC7xhgfC1zQf9
 =Hq1a
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-4.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First round of IIO new device support, features and cleanups for the 4.8 cycle.

New device support
* ads1015
  - add ads1115 support
* bma220 accelerometer
  - new driver
  - triggered buffer support.
* bmc150
  - add bmm150 support.
* bmp280
  - bme280 support with addition of humidity channel.
* max5487 potentiometer
  - new driver
* MMA7660FC accelerometer.
  - New driver
* st-pressure
  - support for the lps22hb
* loop trigger.
  - This one is *nasty* but we have real applications (parrot drones) where
  it is useful.  The trigger basically spins as hard as it can firing off
  a new trigger each time all triggered devices come back to say they are
  done.  It doesn't hang a machine even when doing it on a dummy driver.
  A lot nicer than having this implemented within lots of device drivers
  anyway.

Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
  - IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.

New features
* ak8975
  - support adapters that are limited to byte data only by allowing the
  emulated block read i2c function that was recently introduced.
* atlas-ph
  - support atlas-ec (electrical conductivity sensor)
* bmi160
  - add available frequency and scale attributes to make the driver
  more user friendly (and avoid having to read the datasheet to know
  what will work).
* dummy
  - move creation to configfs interface.  It's not real hardware so we
  are not that worried about the ABI breakage ;)
* mma8452
  - oversampling ration support
* nau7802
  - expose available gains to make life easier for userspace.
* st-sensors
  - allow use of emulation for SMBus block reads as all the st parts support
  it.
* ti-ads1015
  - list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing.  Drop one redundant one
as well.

Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
  - use direct mode claim function rather than open coding it during sensor
  read (prevents switching on buffers mid read).
* ad7793, ad7791
  - use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
  code to do anything useful anyway and that is still being written and under
  control of TI.  Ultimately we may have other libraries to do pulse
  oximetry with these devices but we aren't aware of any yet.
  - kernel-doc format fixes
  - drop ifdef fun around of_match_ptr - it's not worth the mess to save
  a tiny amount of space.
  - drop some unnecessary register initializations.
  - drop the weird locked gain modes as they gain us nothing (can just set
  all gains separately).
  - remove handling of offset attributes seeing as no channels actually have
  them (oops)
  - Drop the LED3 input channel as it's an alias for ALED2.
  - *big one* remove channel names - an experiment that turned out to not
  make sense - see patch for details.
  - use regmap fields to clean up code.
  - tie the tia gain stages to appropriate channels in the ABI as that is
  what they really effect. Same with the LED currents.
  - cleanout some unused defines and fix a missnamed one.
* atlas-ph
  - reorganise to allow support of other similar parts.
* bmc150
  - document supported chips in kconfig help.
* jsa1212
  - drop an unneeded i2c functionality check for functionality the driver
  doesn't use.
* mxs-lradc
  - simply touch screen registration code.
  - remove the touch screen unregister as all devm based now.
  - disable only those channels that are masked in hardware stop (others
  are already dealt with elsewhere)
* st-sensors
  - unexport st_sensors_get_buffer_element as nothing outside the st-sensors
  core driver uses it.
  - fix handling of failure to start up regulators.
* tpl0102
  - drop an i2c functionality test for features that aren't needed.
* ti-am335x
  - use variable name rather than type in sizeof for clarity.
  - use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.

Tools
* Add install / uninstall to makefile.  Someone cares, so presumably
some people will find it useful!
*  generic_buffer
   - rename to iio_generic_buffer to line up with other tools.
   - handle cleanup when receiving signals
   - Add a --device-num option and a --trigger-num option rather than
   relying on naming which doesn't work if you have two of the same part.
2016-06-09 09:15:58 -07:00
Greg Kroah-Hartman 03cce00b4b First round of iio fixes for the 4.7 cycle.
A slightly bumper set due to travel delaying the pull request and a fair few
 issues with the recent merge window patches.  Patches all over the place.
 The st-sensors one is probably the most involved, but definitly solves the
 issues seen.  Note there are some other issues around that handler
 (and the fact that a lot of boards tie a level interrupt chip to an
 edge interrupt only irq chip).  These are not regressions however, so
 will turn up the slow route.
 
 * core
   - iio_trigger_attach_pollfunc had some really badly wrong error handling.
   Another nasty triggered whilst chasing down issues with the st sensors
   rework below.
 * ad5592r
   - fix an off by one error when allocating channels.
 * am2315
   - a stray mutex unlock before we ever take the lock.
 * apds9960
   - missing a parent in the driver model (which should be the i2c device).
   Result is it doesn't turn up under /sys/bus/i2c/devices which some
   userspace code uses for repeatable device identification.
 * as3935
   - ABI usage bug which meant a processed value was reported as raw. Now
     reporting scale as well to ensure userspace has the info it needs.
   - Don't return processed value via the buffer - it doesn't conform to
     the ABI and will overflow in some cases.
   - Fix a wrongly sized buffer which would overflow trashing part of the
     stack.  Also move it onto the heap as part of the fix.
 * bh1780
   - a missing return after write in debugfs lead to an incorrect read and
     a null pointer dereference.
   - dereferencing the wrong pointer in suspend and resume leading to
     unpredictable results.
   - assign a static name to avoid accidentally ending up with no name if
     loaded via device tree.
 * bmi160
   - output data rate for the accelerometer was incorrectly reported. Fix it.
   - writing the output data rate was also wrong due to reverse parameters.
 * bmp280
   - error message for wrong chip ID gave the wrong expected value.
 * hdc100x
   - mask for writing the integration time was wrong allowin g us to get
   'stuck' in a particular value with no way back.
   - temperature reported in celsius rather than millicelsius as per the
   ABI.
   - Get rid of some incorrect data shifting which lead to readings being
   rather incorrect.
 * max44000
   - drop scale attribute for proximity as it is an unscaled value (depends
     on what is in range rather than anything knowable at the detector).
 * st-pressure
   - ABI compliance fixes - units were wrong.
 * st-sensors
   - We introduced some nasty issues with the recent switch over to a
   a somewhat threaded handler in that we broke using a software trigger
   with these devices.  Now do it properly.  It's a larger patch than ideal
   for a fix, but the logic is straight forward.
   - Make sure the trigger is initialized before requesting the interrupt.
   This matters now the interrupt can be shared. Before it was ugly and wrong
   but short of flakey hardware could not be triggered.
   - Hammer down the dataready pin at boot - otherwise with really
   unlucky timing things could get interestingly wedged requiring a hard power
   down of the chip.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXVxMzAAoJEFSFNJnE9BaI3QUP/2TLXJ4S+jNFSGslMmq9Ztqm
 fPGoyPf2nfJCzwgPFK7Yku8mFhqaRbbZrM0m1IA7hYbuZMXZjjQnSrIiDqsDuvXy
 1mK3mieCu8hPFTcvVUp1q9HwrrEFIke52LIH6urSDpr1IIbhJQ2ZwXjZIJGhlukc
 yFwMuA7gz/akc3war+OlS1bbEOe4OuikWMP3Fc3QGKPR7C92M0S8oRyZwBmB2vqu
 1lqCzS0JxL3Lz3TqDXkBd+77My7S4af/F7l8JfeCDBoE4zycASP1LUgiSD2aB3Rq
 hi7hrQjPCFk6rxZ+wFIyC8V0AGeGdEDpQ4JW9rgzDC/KO9Z3Wyq/h5UrQqsnZW0G
 xbJgLF3Wa0noh/bT0yIGZGcenM57QIJ0vTEymmikbWCNQfzqSG9a0SM7zMukB6Lr
 IAvMbF3Q3n/d4rzVOE5C9vRPRnG2jICxmA3EKp7blV0hRdd197J7UfN8ExG+9zC7
 JxqQh5LLu76Ql7TJqQh7sZl/6Xi0DnUm+wqaxyCgtaZjmsVZ58S6G6E2eefO5Hma
 r3VUfthe7N0wnWwCs2RMBkBynhb7+4G11m2jp1a4PMYCYg4FhYP7QdDkeDiOSXbG
 s9Y1ILLI7ufzCyKf5GID7/FtAjdJahVR2ldIy7MwUqw7zAyjsm+ujIpTGZ8iYUvb
 whHwMtLLTnyB8Zj81LRD
 =EEPO
 -----END PGP SIGNATURE-----

Merge tag 'iio-fixes-for-4.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First round of iio fixes for the 4.7 cycle.

A slightly bumper set due to travel delaying the pull request and a fair few
issues with the recent merge window patches.  Patches all over the place.
The st-sensors one is probably the most involved, but definitly solves the
issues seen.  Note there are some other issues around that handler
(and the fact that a lot of boards tie a level interrupt chip to an
edge interrupt only irq chip).  These are not regressions however, so
will turn up the slow route.

* core
  - iio_trigger_attach_pollfunc had some really badly wrong error handling.
  Another nasty triggered whilst chasing down issues with the st sensors
  rework below.
* ad5592r
  - fix an off by one error when allocating channels.
* am2315
  - a stray mutex unlock before we ever take the lock.
* apds9960
  - missing a parent in the driver model (which should be the i2c device).
  Result is it doesn't turn up under /sys/bus/i2c/devices which some
  userspace code uses for repeatable device identification.
* as3935
  - ABI usage bug which meant a processed value was reported as raw. Now
    reporting scale as well to ensure userspace has the info it needs.
  - Don't return processed value via the buffer - it doesn't conform to
    the ABI and will overflow in some cases.
  - Fix a wrongly sized buffer which would overflow trashing part of the
    stack.  Also move it onto the heap as part of the fix.
* bh1780
  - a missing return after write in debugfs lead to an incorrect read and
    a null pointer dereference.
  - dereferencing the wrong pointer in suspend and resume leading to
    unpredictable results.
  - assign a static name to avoid accidentally ending up with no name if
    loaded via device tree.
* bmi160
  - output data rate for the accelerometer was incorrectly reported. Fix it.
  - writing the output data rate was also wrong due to reverse parameters.
* bmp280
  - error message for wrong chip ID gave the wrong expected value.
* hdc100x
  - mask for writing the integration time was wrong allowin g us to get
  'stuck' in a particular value with no way back.
  - temperature reported in celsius rather than millicelsius as per the
  ABI.
  - Get rid of some incorrect data shifting which lead to readings being
  rather incorrect.
* max44000
  - drop scale attribute for proximity as it is an unscaled value (depends
    on what is in range rather than anything knowable at the detector).
* st-pressure
  - ABI compliance fixes - units were wrong.
* st-sensors
  - We introduced some nasty issues with the recent switch over to a
  a somewhat threaded handler in that we broke using a software trigger
  with these devices.  Now do it properly.  It's a larger patch than ideal
  for a fix, but the logic is straight forward.
  - Make sure the trigger is initialized before requesting the interrupt.
  This matters now the interrupt can be shared. Before it was ugly and wrong
  but short of flakey hardware could not be triggered.
  - Hammer down the dataready pin at boot - otherwise with really
  unlucky timing things could get interestingly wedged requiring a hard power
  down of the chip.
2016-06-07 22:26:20 -07:00