The P3310 processor module comes ships with a firmware that implements
PSCI 1.0. Enable and use it to bring up all CPUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA P3310 is a processor module used in several reference designs
that features a Tegra186 SoC, 8 GiB of LPDDR4 RAM, 32 GiB eMMC and other
essentials such as ethernet, WiFi and a PMIC. It is typically connected
to an I/O board (such as the P2597) that provides the connecters needed
to hook it up to the outside world.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has two GPIO controllers that are no longer compatible with the
controller found on earlier generations. One of these controllers exists
in an always-on partition of the SoC whereas the other can be clock- and
powergated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has a total of four SDHCI controllers that each support SD 4.2
(up to UHS-I speed), SDIO 4.1 (up to UHS-I speed), eSD 2.1, eMMC 5.1 and
SDHOST 4.1 (up to UHS-I speed).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has a total of nine I2C controllers that are compatible with
the I2C controllers introduced in Tegra114. Two of these controllers
share pads with two DPAUX controllers (for AUX transactions).
Signed-off-by: Thierry Reding <treding@nvidia.com>
The initial patch only added UARTA, but there's no reason we shouldn't
be adding all of them. While at it, also specify the missing clocks and
resets for UARTA.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has six CPUs: two CPUs are second generation Denver CPUs that
support ARMv8 and four CPUs are Cortex-A57 CPUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the initial support of Tegra186 SoC. It provides enough to
enable the serial console and boot from an initial ramdisk.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[treding@nvidia.com: remove leading 0 from unit-addresses]
[treding@nvidia.com: remove unused nvidia,bpmp property]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull libata updates from Tejun Heo:
- Write same support added
- Minor ahci MSIX irq handling updates
- Non-critical SCSI command translation fixes
- Controller specific changes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: Revert "ahci: qoriq: Disable NCQ on ls2080a SoC"
libata: remove <asm-generic/libata-portmap.h>
libata: remove unused definitions from <asm/libata-portmap.h>
pata_at91: Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
ata: Replace BUG() with BUG_ON().
ata: sata_mv: Replacing dma_pool_alloc and memset with a single call dma_pool_zalloc.
libata: Some drives failing on SCT Write Same
ahci: use pci_alloc_irq_vectors
libata: SCT Write Same handle ATA_DFLAG_PIO
libata: SCT Write Same / DSM Trim
libata: Add support for SCT Write Same
libata: Safely overwrite attached page in WRITE SAME xlat
ahci: also use a per-port lock for the multi-MSIX case
ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
ahci: st: Add ports-implemented property in support
ahci: qoriq: enable snoopable sata read and write
ahci: qoriq: adjust sata parameter
libata-scsi: fix MODE SELECT translation for Control mode page
libata-scsi: use u8 array to store mode page copy
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
The 64-bit DT changes are surprisingly small this time, we only add two
SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
UniPhier LD11 TV SoC, each with their reference boards.
There are three new machines added for existing SoC platforms:
- The Marvell Armada 8040 development board is an impressive quad-core
Cortex-A72 machine with three 10gbit ethernet interfaces
- Qualcomms DragonBoard 820c single-board computer is their current
high-end phone platform in the 96boards form factor
- Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
Android box based on the 8-core rk3368 SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PxJN
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"The 64-bit DT changes are surprisingly small this time, we only add
two SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
UniPhier LD11 TV SoC, each with their reference boards.
There are three new machines added for existing SoC platforms:
- The Marvell Armada 8040 development board is an impressive
quad-core Cortex-A72 machine with three 10gbit ethernet interfaces
- Qualcomms DragonBoard 820c single-board computer is their current
high-end phone platform in the 96boards form factor
- Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
Android box based on the 8-core rk3368 SoC"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (91 commits)
arm64: dts: berlin4ct: Add L2 cache topology
arm64: dts: berlin4ct: enable all wdt nodes unconditionally
arm64: dts: berlin4ct: switch to Cortex-A53 specific pmu nodes
arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
arm64: dts: apm: Add DT node for APM X-Gene 2 CPU clocks
arm64: dts: apm: Add X-Gene SoC hwmon to device tree
arm64: dts: apm: Fix interrupt polarity for X-Gene PCIe legacy interrupts
arm64: dts: apm: Add APM X-Gene v2 SoC PMU DTS entries
arm64: dts: apm: Add APM X-Gene SoC PMU DTS entries
arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
...
This patch adds the L2 cache topology for berlin4ct which has 1MB L2
cache.
[Sebastian: rename cache node from "l2-cache" to "cache"]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
After commit f29a72c24a ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Commit ac82d12772 ("arm64: perf: add Cortex-A53 support") adds the
cortex A53 PMU support, thus instead of using the generic armv8-pmuv3
compatibility use the more specific Cortex A53 compatibility.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones on Tegra210, these trips can trigger shut down or reset.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Adds soctherm node for Tegra210, and add cpu,
gpu, mem, pllx as thermal-zones. Set critical
trip temperatures for them.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones on Tegra132, these trips can trigger shut down or reset.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Tegra132 has the specific settings for soctherm,
so change to use campatible "nvidia,tegra132-soctherm" for it.
And adds cpu, gpu, mem and pllx thermal zones.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
- Add initial DTS support for ZTE ZX296718 SoC and ZX296718 EVB board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX22SoAAoJEFBXWFqHsHzOypkIAIj88TKFW6IWuiM+mFwu2Q3X
3sqKB11szxucCd8XYHUQ/wknZX33sDSj63mUbYN20Mb4AbA7u1KG/hR6mBIq3no7
xnIDixq6kIMmt3dY6OEgu3qlkEQnrbopcp7bt3N1QtXNtQazt5WWStSzBwAz1Qsq
QQMUjoOyp3sx3E48HiAmPo2R8oh231w44aKS87YU7IIa3Ld9SyNW6/t8sAAhqvWH
1DLFNgZ968jmbb46BylPSHslMSmjrv1HR+5nZ3zNOQeDcRvLqi7+z9xqhwJUVr08
DXh90RaZNSULHlMWL3lEBLR9KTlca2+08c4ax5YOVeAQjaf+ZUAQUPGod+IBW7M=
=KfUg
-----END PGP SIGNATURE-----
Merge tag 'zte-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "ZTE arm64 device tree changes for 4.9" from Shawn Guo:
- Add initial DTS support for ZTE ZX296718 SoC and ZX296718 EVB board.
* tag 'zte-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
- enable MSI for PCIe on Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfZZyIACgkQCwYYjhRyO9WV9wCgplO/RTXtSazA02kkUsDSPezd
tVkAnREnwZSo9CzGdQnEztgOpihvgBMH
=2st8
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.9-2' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt64 for 4.9 (part 2)" from Gregory CLEMENT:
- enable MSI for PCIe on Armada 7K/8K
* tag 'mvebu-dt64-4.9-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
Here are a couple of bugfixes for v4.8-rc. Most of them have
actually been around for a while this time but for some reason
didn't get applied early on. The shmobile regulator fix is the
only one that isn't completely obvious.
device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- A new use of skeleton.dtsi on arm64 has crept in after that
was removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tYAb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple of bugfixes for v4.8-rc.
Most of them have actually been around for a while this time but for
some reason didn't get applied early on. The shmobile regulator fix
is the only one that isn't completely obvious.
Device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- a new use of skeleton.dtsi on arm64 has crept in after that was
removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
Code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
Maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: defconfig: Fix USB configuration
arm64: dts: Fix broken architected timer interrupt trigger
ARM: multi_v7_defconfig: update XILINX_VDMA
ARM64: dts: bcm: Use a symlink to R-Pi dtsi files from arch=arm
ARM: dts: Remove use of skeleton.dtsi from bcm283x.dtsi
ARM: dts: STiH407-family: Provide interconnect clock for consumption in ST SDHCI
ARM: dts: STiH410: Handle interconnect clock required by EHCI/OHCI (USB)
ARM: shmobile: fix regulator quirk for Gen2
ARM: EXYNOS: Clear OF_POPULATED flag from PMU node in IRQ init callback
MAINTAINERS: Add myself as reviewer for Samsung Exynos support
Add device tree support for ZX296718 SoC and evaluation board based
on it. Also document new values.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[khilman: rename vbus node to match P200 schematics]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
* dt/irq-fix:
arm64: dts: Fix broken architected timer interrupt trigger
This resolves a non-obvious conflict between a bugfix from
v4.8 and a cleanup for the exynos7 platform.
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the nodes for the dwc2 USB controller and the related USB PHYs.
Currently we force usb0 to host mode because OTG is currently not
working in our PHY driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for i2c bus on gxbb based platforms.
On the OdroidC2 (I2C A) and P200 (I2C B), the pull-up resistor are
present directly on the board. This indicates that these pins are
dedicated to i2c.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This is used to configure the pins of the sd_emmc_a controller to
which an SDIO module is connected (when available).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic reference driver uses the "mc_val" devicetree property to
configure the PRG_ETHERNET_ADDR0 register. Unfortunately it uses magic
values for this configuration.
According to the datasheet the PRG_ETHERNET_ADDR0 register is at address
0xc8834108. However, the reference driver uses 0xc8834540 instead.
According to my tests, the value from the reference driver is correct.
No changes are required to the board dts files because the only
required configuration option is the phy-mode, which had to be
configured correctly before as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All of these have a Realtek Gbit RGMII PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
