In short, sctp is likely to incorrectly choose src address if socket is
bound to secondary addresses. This patch fixes it by adding a new check
that checks if such src address belongs to the interface that routing
identified as output.
This is enough to avoid rp_filter drops on remote peer.
Details:
Currently, sctp will do a routing attempt without specifying the src
address and compare the returned value (preferred source) with the
addresses that the socket is bound to. When using secondary addresses,
this will not match.
Then it will try specifying each of the addresses that the socket is
bound to and re-routing, checking if that address is valid as src for
that dst. Thing is, this check alone is weak:
# ip r l
192.168.100.0/24 dev eth1 proto kernel scope link src 192.168.100.149
192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.147
# ip a l
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:54:00:15:18:6a brd ff:ff:ff:ff:ff:ff
inet 192.168.122.147/24 brd 192.168.122.255 scope global dynamic eth0
valid_lft 2160sec preferred_lft 2160sec
inet 192.168.122.148/24 scope global secondary eth0
valid_lft forever preferred_lft forever
inet6 fe80::5054:ff:fe15:186a/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:54:00:b3:91:46 brd ff:ff:ff:ff:ff:ff
inet 192.168.100.149/24 brd 192.168.100.255 scope global dynamic eth1
valid_lft 2162sec preferred_lft 2162sec
inet 192.168.100.148/24 scope global secondary eth1
valid_lft forever preferred_lft forever
inet6 fe80::5054:ff:feb3:9146/64 scope link
valid_lft forever preferred_lft forever
4: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:54:00:05:47:ee brd ff:ff:ff:ff:ff:ff
inet6 fe80::5054:ff:fe05:47ee/64 scope link
valid_lft forever preferred_lft forever
# ip r g 192.168.100.193 from 192.168.122.148
192.168.100.193 from 192.168.122.148 dev eth1
cache
Even if you specify an interface:
# ip r g 192.168.100.193 from 192.168.122.148 oif eth1
192.168.100.193 from 192.168.122.148 dev eth1
cache
Although this would be valid, peers using rp_filter will drop such
packets as their src doesn't match the routes for that interface.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paves the day for the next patch. Functionality stays untouched.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
->auto_asconf_splist is per namespace and mangled by functions like
sctp_setsockopt_auto_asconf() which doesn't guarantee any serialization.
Also, the call to inet_sk_copy_descendant() was backuping
->auto_asconf_list through the copy but was not honoring
->do_auto_asconf, which could lead to list corruption if it was
different between both sockets.
This commit thus fixes the list handling by using ->addr_wq_lock
spinlock to protect the list. A special handling is done upon socket
creation and destruction for that. Error handlig on sctp_init_sock()
will never return an error after having initialized asconf, so
sctp_destroy_sock() can be called without addrq_wq_lock. The lock now
will be take on sctp_close_sock(), before locking the socket, so we
don't do it in inverse order compared to sctp_addr_wq_timeout_handler().
Instead of taking the lock on sctp_sock_migrate() for copying and
restoring the list values, it's preferred to avoid rewritting it by
implementing sctp_copy_descendant().
Issue was found with a test application that kept flipping sysctl
default_auto_asconf on and off, but one could trigger it by issuing
simultaneous setsockopt() calls on multiple sockets or by
creating/destroying sockets fast enough. This is only triggerable
locally.
Fixes: 9f7d653b67 ("sctp: Add Auto-ASCONF support (core).")
Reported-by: Ji Jianwen <jiji@redhat.com>
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we can ask to authenticate DATA chunks and we can send DATA
chunks on the same packet as COOKIE_ECHO, but if you try to combine
both, the DATA chunk will be sent unauthenticated and peer won't accept
it, leading to a communication failure.
This happens because even though the data was queued after it was
requested to authenticate DATA chunks, it was also queued before we
could know that remote peer can handle authenticating, so
sctp_auth_send_cid() returns false.
The fix is whenever we set up an active key, re-check send queue for
chunks that now should be authenticated. As a result, such packet will
now contain COOKIE_ECHO + AUTH + DATA chunks, in that order.
Reported-by: Liu Wei <weliu@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of doing the rt6->rt6i_node check whenever we need
to get the route's cookie. Refactor it into rt6_get_cookie().
It is a prep work to handle FLOWI_FLAG_KNOWN_NH and also
percpu rt6_info later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the assumptions that the returned rt is always
a RTF_CACHE entry with the rt6i_dst and rt6i_src containing the
destination and source address. The dst and src can be recovered from
the calling site.
We may consider to rename (rt6i_dst, rt6i_src) to
(rt6i_key_dst, rt6i_key_src) later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for changing how struct net is refcounted
on kernel sockets pass the knowledge that we are creating
a kernel socket from sock_create_kern through to sk_alloc.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the declaration for external variables to sctp.h file avoiding
to repeatedly declare them with extern keyword.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[] use a common
macro in protocol families using skb->cb[] for ancillary data to
validate available room in skb->cb[].
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.
At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().
Fixes: d6de309759 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <saran.neti@telus.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hitting an INIT collision case during the 4WHS with AUTH enabled, as
already described in detail in commit 1be9a950c6 ("net: sctp: inherit
auth_capable on INIT collisions"), it can happen that we occasionally
still remotely trigger the following panic on server side which seems to
have been uncovered after the fix from commit 1be9a950c6 ...
[ 533.876389] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 533.913657] IP: [<ffffffff811ac385>] __kmalloc+0x95/0x230
[ 533.940559] PGD 5030f2067 PUD 0
[ 533.957104] Oops: 0000 [#1] SMP
[ 533.974283] Modules linked in: sctp mlx4_en [...]
[ 534.939704] Call Trace:
[ 534.951833] [<ffffffff81294e30>] ? crypto_init_shash_ops+0x60/0xf0
[ 534.984213] [<ffffffff81294e30>] crypto_init_shash_ops+0x60/0xf0
[ 535.015025] [<ffffffff8128c8ed>] __crypto_alloc_tfm+0x6d/0x170
[ 535.045661] [<ffffffff8128d12c>] crypto_alloc_base+0x4c/0xb0
[ 535.074593] [<ffffffff8160bd42>] ? _raw_spin_lock_bh+0x12/0x50
[ 535.105239] [<ffffffffa0418c11>] sctp_inet_listen+0x161/0x1e0 [sctp]
[ 535.138606] [<ffffffff814e43bd>] SyS_listen+0x9d/0xb0
[ 535.166848] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b
... or depending on the the application, for example this one:
[ 1370.026490] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 1370.026506] IP: [<ffffffff811ab455>] kmem_cache_alloc+0x75/0x1d0
[ 1370.054568] PGD 633c94067 PUD 0
[ 1370.070446] Oops: 0000 [#1] SMP
[ 1370.085010] Modules linked in: sctp kvm_amd kvm [...]
[ 1370.963431] Call Trace:
[ 1370.974632] [<ffffffff8120f7cf>] ? SyS_epoll_ctl+0x53f/0x960
[ 1371.000863] [<ffffffff8120f7cf>] SyS_epoll_ctl+0x53f/0x960
[ 1371.027154] [<ffffffff812100d3>] ? anon_inode_getfile+0xd3/0x170
[ 1371.054679] [<ffffffff811e3d67>] ? __alloc_fd+0xa7/0x130
[ 1371.080183] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b
With slab debugging enabled, we can see that the poison has been overwritten:
[ 669.826368] BUG kmalloc-128 (Tainted: G W ): Poison overwritten
[ 669.826385] INFO: 0xffff880228b32e50-0xffff880228b32e50. First byte 0x6a instead of 0x6b
[ 669.826414] INFO: Allocated in sctp_auth_create_key+0x23/0x50 [sctp] age=3 cpu=0 pid=18494
[ 669.826424] __slab_alloc+0x4bf/0x566
[ 669.826433] __kmalloc+0x280/0x310
[ 669.826453] sctp_auth_create_key+0x23/0x50 [sctp]
[ 669.826471] sctp_auth_asoc_create_secret+0xcb/0x1e0 [sctp]
[ 669.826488] sctp_auth_asoc_init_active_key+0x68/0xa0 [sctp]
[ 669.826505] sctp_do_sm+0x29d/0x17c0 [sctp] [...]
[ 669.826629] INFO: Freed in kzfree+0x31/0x40 age=1 cpu=0 pid=18494
[ 669.826635] __slab_free+0x39/0x2a8
[ 669.826643] kfree+0x1d6/0x230
[ 669.826650] kzfree+0x31/0x40
[ 669.826666] sctp_auth_key_put+0x19/0x20 [sctp]
[ 669.826681] sctp_assoc_update+0x1ee/0x2d0 [sctp]
[ 669.826695] sctp_do_sm+0x674/0x17c0 [sctp]
Since this only triggers in some collision-cases with AUTH, the problem at
heart is that sctp_auth_key_put() on asoc->asoc_shared_key is called twice
when having refcnt 1, once directly in sctp_assoc_update() and yet again
from within sctp_auth_asoc_init_active_key() via sctp_assoc_update() on
the already kzfree'd memory, which is also consistent with the observation
of the poison decrease from 0x6b to 0x6a (note: the overwrite is detected
at a later point in time when poison is checked on new allocation).
Reference counting of auth keys revisited:
Shared keys for AUTH chunks are being stored in endpoints and associations
in endpoint_shared_keys list. On endpoint creation, a null key is being
added; on association creation, all endpoint shared keys are being cached
and thus cloned over to the association. struct sctp_shared_key only holds
a pointer to the actual key bytes, that is, struct sctp_auth_bytes which
keeps track of users internally through refcounting. Naturally, on assoc
or enpoint destruction, sctp_shared_key are being destroyed directly and
the reference on sctp_auth_bytes dropped.
User space can add keys to either list via setsockopt(2) through struct
sctp_authkey and by passing that to sctp_auth_set_key() which replaces or
adds a new auth key. There, sctp_auth_create_key() creates a new sctp_auth_bytes
with refcount 1 and in case of replacement drops the reference on the old
sctp_auth_bytes. A key can be set active from user space through setsockopt()
on the id via sctp_auth_set_active_key(), which iterates through either
endpoint_shared_keys and in case of an assoc, invokes (one of various places)
sctp_auth_asoc_init_active_key().
sctp_auth_asoc_init_active_key() computes the actual secret from local's
and peer's random, hmac and shared key parameters and returns a new key
directly as sctp_auth_bytes, that is asoc->asoc_shared_key, plus drops
the reference if there was a previous one. The secret, which where we
eventually double drop the ref comes from sctp_auth_asoc_set_secret() with
intitial refcount of 1, which also stays unchanged eventually in
sctp_assoc_update(). This key is later being used for crypto layer to
set the key for the hash in crypto_hash_setkey() from sctp_auth_calculate_hmac().
To close the loop: asoc->asoc_shared_key is freshly allocated secret
material and independant of the sctp_shared_key management keeping track
of only shared keys in endpoints and assocs. Hence, also commit 4184b2a79a
("net: sctp: fix memory leak in auth key management") is independant of
this bug here since it concerns a different layer (though same structures
being used eventually). asoc->asoc_shared_key is reference dropped correctly
on assoc destruction in sctp_association_free() and when active keys are
being replaced in sctp_auth_asoc_init_active_key(), it always has a refcount
of 1. Hence, it's freed prematurely in sctp_assoc_update(). Simple fix is
to remove that sctp_auth_key_put() from there which fixes these panics.
Fixes: 730fc3d05c ("[SCTP]: Implete SCTP-AUTH parameter processing")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I.e. one-to-many sockets in SCTP are not required to explicitly
call into connect(2) or sctp_connectx(2) prior to data exchange.
Instead, they can directly invoke sendmsg(2) and the SCTP stack
will automatically trigger connection establishment through 4WHS
via sctp_primitive_ASSOCIATE(). However, this in its current
implementation is racy: INIT is being sent out immediately (as
it cannot be bundled anyway) and the rest of the DATA chunks are
queued up for later xmit when connection is established, meaning
sendmsg(2) will return successfully. This behaviour can result
in an undesired side-effect that the kernel made the application
think the data has already been transmitted, although none of it
has actually left the machine, worst case even after close(2)'ing
the socket.
Instead, when the association from client side has been shut down
e.g. first gracefully through SCTP_EOF and then close(2), the
client could afterwards still receive the server's INIT_ACK due
to a connection with higher latency. This INIT_ACK is then considered
out of the blue and hence responded with ABORT as there was no
alive assoc found anymore. This can be easily reproduced f.e.
with sctp_test application from lksctp. One way to fix this race
is to wait for the handshake to actually complete.
The fix defers waiting after sctp_primitive_ASSOCIATE() and
sctp_primitive_SEND() succeeded, so that DATA chunks cooked up
from sctp_sendmsg() have already been placed into the output
queue through the side-effect interpreter, and therefore can then
be bundeled together with COOKIE_ECHO control chunks.
strace from example application (shortened):
socket(PF_INET, SOCK_SEQPACKET, IPPROTO_SCTP) = 3
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(0)=[], msg_controllen=48, {cmsg_len=48, cmsg_level=0x84 /* SOL_??? */, cmsg_type=, ...},
msg_flags=0}, 0) = 0 // graceful shutdown for SOCK_SEQPACKET via SCTP_EOF
close(3) = 0
tcpdump before patch (fooling the application):
22:33:36.306142 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 3879023686] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3139201684]
22:33:36.316619 IP 192.168.1.115.8888 > 192.168.1.114.41462: sctp (1) [INIT ACK] [init tag: 3345394793] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 3380109591]
22:33:36.317600 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [ABORT]
tcpdump after patch:
14:28:58.884116 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 438593213] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3092969729]
14:28:58.888414 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [INIT ACK] [init tag: 381429855] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 2141904492]
14:28:58.888638 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [COOKIE ECHO] , (2) [DATA] (B)(E) [TSN: 3092969729] [...]
14:28:58.893278 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [COOKIE ACK] , (2) [SACK] [cum ack 3092969729] [a_rwnd 106491] [#gap acks 0] [#dup tsns 0]
14:28:58.893591 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969730] [...]
14:28:59.096963 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969730] [a_rwnd 106496] [#gap acks 0] [#dup tsns 0]
14:28:59.097086 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969731] [...] , (2) [DATA] (B)(E) [TSN: 3092969732] [...]
14:28:59.103218 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969732] [a_rwnd 106486] [#gap acks 0] [#dup tsns 0]
14:28:59.103330 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN]
14:28:59.107793 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SHUTDOWN ACK]
14:28:59.107890 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN COMPLETE]
Looks like this bug is from the pre-git history museum. ;)
Fixes: 08707d5482df ("lksctp-2_5_31-0_5_1.patch")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce helper macro for_each_cmsghdr as a wrapper of the enumerating
cmsghdr from msghdr, just cleanup.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that the code _using_ ->msg_iter at that point will be very
unhappy with anything other than unshifted iovec-backed iov_iter.
We still need to convert users to proper primitives.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To accomodate for enough headroom for tunnels, use MAX_HEADER instead
of LL_MAX_HEADER. Robert reported that he has hit after roughly 40hrs
of trinity an skb_under_panic() via SCTP output path (see reference).
I couldn't reproduce it from here, but not using MAX_HEADER as elsewhere
in other protocols might be one possible cause for this.
In any case, it looks like accounting on chunks themself seems to look
good as the skb already passed the SCTP output path and did not hit
any skb_over_panic(). Given tunneling was enabled in his .config, the
headroom would have been expanded by MAX_HEADER in this case.
Reported-by: Robert Święcki <robert@swiecki.net>
Reference: https://lkml.org/lkml/2014/12/1/507
Fixes: 594ccc14df ("[SCTP] Replace incorrect use of dev_alloc_skb with alloc_skb in sctp_packet_transmit().")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's just silly to hold the skb destructor argument around inside
skb->cb[] as we currently do in SCTP.
Nowadays, we're sort of cheating on data accounting in the sense
that due to commit 4c3a5bdae2 ("sctp: Don't charge for data in
sndbuf again when transmitting packet"), we orphan the skb already
in the SCTP output path, i.e. giving back charged data memory, and
use a different destructor only to make sure the sk doesn't vanish
on skb destruction time. Thus, cb[] is still valid here as we
operate within the SCTP layer. (It's generally actually a big
candidate for future rework, imho.)
However, storing the destructor in the cb[] can easily cause issues
should an non sctp_packet_set_owner_w()'ed skb ever escape the SCTP
layer, since cb[] may get overwritten by lower layers and thus can
corrupt the chunk pointer. There are no such issues at present,
but lets keep the chunk in destructor_arg, as this is the actual
purpose for it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
A very minimal and simple user space application allocating an SCTP
socket, setting SCTP_AUTH_KEY setsockopt(2) on it and then closing
the socket again will leak the memory containing the authentication
key from user space:
unreferenced object 0xffff8800837047c0 (size 16):
comm "a.out", pid 2789, jiffies 4296954322 (age 192.258s)
hex dump (first 16 bytes):
01 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff816d7e8e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811c88d8>] __kmalloc+0xe8/0x270
[<ffffffffa0870c23>] sctp_auth_create_key+0x23/0x50 [sctp]
[<ffffffffa08718b1>] sctp_auth_set_key+0xa1/0x140 [sctp]
[<ffffffffa086b383>] sctp_setsockopt+0xd03/0x1180 [sctp]
[<ffffffff815bfd94>] sock_common_setsockopt+0x14/0x20
[<ffffffff815beb61>] SyS_setsockopt+0x71/0xd0
[<ffffffff816e58a9>] system_call_fastpath+0x12/0x17
[<ffffffffffffffff>] 0xffffffffffffffff
This is bad because of two things, we can bring down a machine from
user space when auth_enable=1, but also we would leave security sensitive
keying material in memory without clearing it after use. The issue is
that sctp_auth_create_key() already sets the refcount to 1, but after
allocation sctp_auth_set_key() does an additional refcount on it, and
thus leaving it around when we free the socket.
Fixes: 65b07e5d0d ("[SCTP]: API updates to suport SCTP-AUTH extensions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SCTP server doing ASCONF will panic on malformed INIT ping-of-death
in the form of:
------------ INIT[PARAM: SET_PRIMARY_IP] ------------>
While the INIT chunk parameter verification dissects through many things
in order to detect malformed input, it misses to actually check parameters
inside of parameters. E.g. RFC5061, section 4.2.4 proposes a 'set primary
IP address' parameter in ASCONF, which has as a subparameter an address
parameter.
So an attacker may send a parameter type other than SCTP_PARAM_IPV4_ADDRESS
or SCTP_PARAM_IPV6_ADDRESS, param_type2af() will subsequently return 0
and thus sctp_get_af_specific() returns NULL, too, which we then happily
dereference unconditionally through af->from_addr_param().
The trace for the log:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000078
IP: [<ffffffffa01e9c62>] sctp_process_init+0x492/0x990 [sctp]
PGD 0
Oops: 0000 [#1] SMP
[...]
Pid: 0, comm: swapper Not tainted 2.6.32-504.el6.x86_64 #1 Bochs Bochs
RIP: 0010:[<ffffffffa01e9c62>] [<ffffffffa01e9c62>] sctp_process_init+0x492/0x990 [sctp]
[...]
Call Trace:
<IRQ>
[<ffffffffa01f2add>] ? sctp_bind_addr_copy+0x5d/0xe0 [sctp]
[<ffffffffa01e1fcb>] sctp_sf_do_5_1B_init+0x21b/0x340 [sctp]
[<ffffffffa01e3751>] sctp_do_sm+0x71/0x1210 [sctp]
[<ffffffffa01e5c09>] ? sctp_endpoint_lookup_assoc+0xc9/0xf0 [sctp]
[<ffffffffa01e61f6>] sctp_endpoint_bh_rcv+0x116/0x230 [sctp]
[<ffffffffa01ee986>] sctp_inq_push+0x56/0x80 [sctp]
[<ffffffffa01fcc42>] sctp_rcv+0x982/0xa10 [sctp]
[<ffffffffa01d5123>] ? ipt_local_in_hook+0x23/0x28 [iptable_filter]
[<ffffffff8148bdc9>] ? nf_iterate+0x69/0xb0
[<ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[<ffffffff8148bf86>] ? nf_hook_slow+0x76/0x120
[<ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[...]
A minimal way to address this is to check for NULL as we do on all
other such occasions where we know sctp_get_af_specific() could
possibly return with NULL.
Fixes: d6de309759 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alternative to RPS/RFS is to use hardware support for multiple
queues.
Then split a set of million of sockets into worker threads, each
one using epoll() to manage events on its own socket pool.
Ideally, we want one thread per RX/TX queue/cpu, but we have no way to
know after accept() or connect() on which queue/cpu a socket is managed.
We normally use one cpu per RX queue (IRQ smp_affinity being properly
set), so remembering on socket structure which cpu delivered last packet
is enough to solve the problem.
After accept(), connect(), or even file descriptor passing around
processes, applications can use :
int cpu;
socklen_t len = sizeof(cpu);
getsockopt(fd, SOL_SOCKET, SO_INCOMING_CPU, &cpu, &len);
And use this information to put the socket into the right silo
for optimal performance, as all networking stack should run
on the appropriate cpu, without need to send IPI (RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".
When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.
Having a helper like this means there will be less places to touch
during that transformation.
Based upon descriptions and patch from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes checkpatch warning:
"WARNING: Prefer seq_puts to seq_printf"
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is often quite helpful to be able to know the state of a transport
outside of the application itself (for troubleshooting purposes or for
monitoring purposes). Add it under /proc/net/sctp/remaddr.
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
This scenario is not limited to ASCONF, just taken as one
example triggering the issue. When receiving ASCONF probes
in the form of ...
-------------- INIT[ASCONF; ASCONF_ACK] ------------->
<----------- INIT-ACK[ASCONF; ASCONF_ACK] ------------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
---- ASCONF_a; [ASCONF_b; ...; ASCONF_n;] JUNK ------>
[...]
---- ASCONF_m; [ASCONF_o; ...; ASCONF_z;] JUNK ------>
... where ASCONF_a, ASCONF_b, ..., ASCONF_z are good-formed
ASCONFs and have increasing serial numbers, we process such
ASCONF chunk(s) marked with !end_of_packet and !singleton,
since we have not yet reached the SCTP packet end. SCTP does
only do verification on a chunk by chunk basis, as an SCTP
packet is nothing more than just a container of a stream of
chunks which it eats up one by one.
We could run into the case that we receive a packet with a
malformed tail, above marked as trailing JUNK. All previous
chunks are here goodformed, so the stack will eat up all
previous chunks up to this point. In case JUNK does not fit
into a chunk header and there are no more other chunks in
the input queue, or in case JUNK contains a garbage chunk
header, but the encoded chunk length would exceed the skb
tail, or we came here from an entirely different scenario
and the chunk has pdiscard=1 mark (without having had a flush
point), it will happen, that we will excessively queue up
the association's output queue (a correct final chunk may
then turn it into a response flood when flushing the
queue ;)): I ran a simple script with incremental ASCONF
serial numbers and could see the server side consuming
excessive amount of RAM [before/after: up to 2GB and more].
The issue at heart is that the chunk train basically ends
with !end_of_packet and !singleton markers and since commit
2e3216cd54 ("sctp: Follow security requirement of responding
with 1 packet") therefore preventing an output queue flush
point in sctp_do_sm() -> sctp_cmd_interpreter() on the input
chunk (chunk = event_arg) even though local_cork is set,
but its precedence has changed since then. In the normal
case, the last chunk with end_of_packet=1 would trigger the
queue flush to accommodate possible outgoing bundling.
In the input queue, sctp_inq_pop() seems to do the right thing
in terms of discarding invalid chunks. So, above JUNK will
not enter the state machine and instead be released and exit
the sctp_assoc_bh_rcv() chunk processing loop. It's simply
the flush point being missing at loop exit. Adding a try-flush
approach on the output queue might not work as the underlying
infrastructure might be long gone at this point due to the
side-effect interpreter run.
One possibility, albeit a bit of a kludge, would be to defer
invalid chunk freeing into the state machine in order to
possibly trigger packet discards and thus indirectly a queue
flush on error. It would surely be better to discard chunks
as in the current, perhaps better controlled environment, but
going back and forth, it's simply architecturally not possible.
I tried various trailing JUNK attack cases and it seems to
look good now.
Joint work with Vlad Yasevich.
Fixes: 2e3216cd54 ("sctp: Follow security requirement of responding with 1 packet")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a e.g. semi-good formed connection scan in the
form of ...
-------------- INIT[ASCONF; ASCONF_ACK] ------------->
<----------- INIT-ACK[ASCONF; ASCONF_ACK] ------------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
---------------- ASCONF_a; ASCONF_b ----------------->
... where ASCONF_a equals ASCONF_b chunk (at least both serials
need to be equal), we panic an SCTP server!
The problem is that good-formed ASCONF chunks that we reply with
ASCONF_ACK chunks are cached per serial. Thus, when we receive a
same ASCONF chunk twice (e.g. through a lost ASCONF_ACK), we do
not need to process them again on the server side (that was the
idea, also proposed in the RFC). Instead, we know it was cached
and we just resend the cached chunk instead. So far, so good.
Where things get nasty is in SCTP's side effect interpreter, that
is, sctp_cmd_interpreter():
While incoming ASCONF_a (chunk = event_arg) is being marked
!end_of_packet and !singleton, and we have an association context,
we do not flush the outqueue the first time after processing the
ASCONF_ACK singleton chunk via SCTP_CMD_REPLY. Instead, we keep it
queued up, although we set local_cork to 1. Commit 2e3216cd54
changed the precedence, so that as long as we get bundled, incoming
chunks we try possible bundling on outgoing queue as well. Before
this commit, we would just flush the output queue.
Now, while ASCONF_a's ASCONF_ACK sits in the corked outq, we
continue to process the same ASCONF_b chunk from the packet. As
we have cached the previous ASCONF_ACK, we find it, grab it and
do another SCTP_CMD_REPLY command on it. So, effectively, we rip
the chunk->list pointers and requeue the same ASCONF_ACK chunk
another time. Since we process ASCONF_b, it's correctly marked
with end_of_packet and we enforce an uncork, and thus flush, thus
crashing the kernel.
Fix it by testing if the ASCONF_ACK is currently pending and if
that is the case, do not requeue it. When flushing the output
queue we may relink the chunk for preparing an outgoing packet,
but eventually unlink it when it's copied into the skb right
before transmission.
Joint work with Vlad Yasevich.
Fixes: 2e3216cd54 ("sctp: Follow security requirement of responding with 1 packet")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6f4c618ddb ("SCTP : Add paramters validity check for
ASCONF chunk") added basic verification of ASCONF chunks, however,
it is still possible to remotely crash a server by sending a
special crafted ASCONF chunk, even up to pre 2.6.12 kernels:
skb_over_panic: text:ffffffffa01ea1c3 len:31056 put:30768
head:ffff88011bd81800 data:ffff88011bd81800 tail:0x7950
end:0x440 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:129!
[...]
Call Trace:
<IRQ>
[<ffffffff8144fb1c>] skb_put+0x5c/0x70
[<ffffffffa01ea1c3>] sctp_addto_chunk+0x63/0xd0 [sctp]
[<ffffffffa01eadaf>] sctp_process_asconf+0x1af/0x540 [sctp]
[<ffffffff8152d025>] ? _read_unlock_bh+0x15/0x20
[<ffffffffa01e0038>] sctp_sf_do_asconf+0x168/0x240 [sctp]
[<ffffffffa01e3751>] sctp_do_sm+0x71/0x1210 [sctp]
[<ffffffff8147645d>] ? fib_rules_lookup+0xad/0xf0
[<ffffffffa01e6b22>] ? sctp_cmp_addr_exact+0x32/0x40 [sctp]
[<ffffffffa01e8393>] sctp_assoc_bh_rcv+0xd3/0x180 [sctp]
[<ffffffffa01ee986>] sctp_inq_push+0x56/0x80 [sctp]
[<ffffffffa01fcc42>] sctp_rcv+0x982/0xa10 [sctp]
[<ffffffffa01d5123>] ? ipt_local_in_hook+0x23/0x28 [iptable_filter]
[<ffffffff8148bdc9>] ? nf_iterate+0x69/0xb0
[<ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[<ffffffff8148bf86>] ? nf_hook_slow+0x76/0x120
[<ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[<ffffffff81496ded>] ip_local_deliver_finish+0xdd/0x2d0
[<ffffffff81497078>] ip_local_deliver+0x98/0xa0
[<ffffffff8149653d>] ip_rcv_finish+0x12d/0x440
[<ffffffff81496ac5>] ip_rcv+0x275/0x350
[<ffffffff8145c88b>] __netif_receive_skb+0x4ab/0x750
[<ffffffff81460588>] netif_receive_skb+0x58/0x60
This can be triggered e.g., through a simple scripted nmap
connection scan injecting the chunk after the handshake, for
example, ...
-------------- INIT[ASCONF; ASCONF_ACK] ------------->
<----------- INIT-ACK[ASCONF; ASCONF_ACK] ------------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
------------------ ASCONF; UNKNOWN ------------------>
... where ASCONF chunk of length 280 contains 2 parameters ...
1) Add IP address parameter (param length: 16)
2) Add/del IP address parameter (param length: 255)
... followed by an UNKNOWN chunk of e.g. 4 bytes. Here, the
Address Parameter in the ASCONF chunk is even missing, too.
This is just an example and similarly-crafted ASCONF chunks
could be used just as well.
The ASCONF chunk passes through sctp_verify_asconf() as all
parameters passed sanity checks, and after walking, we ended
up successfully at the chunk end boundary, and thus may invoke
sctp_process_asconf(). Parameter walking is done with
WORD_ROUND() to take padding into account.
In sctp_process_asconf()'s TLV processing, we may fail in
sctp_process_asconf_param() e.g., due to removal of the IP
address that is also the source address of the packet containing
the ASCONF chunk, and thus we need to add all TLVs after the
failure to our ASCONF response to remote via helper function
sctp_add_asconf_response(), which basically invokes a
sctp_addto_chunk() adding the error parameters to the given
skb.
When walking to the next parameter this time, we proceed
with ...
length = ntohs(asconf_param->param_hdr.length);
asconf_param = (void *)asconf_param + length;
... instead of the WORD_ROUND()'ed length, thus resulting here
in an off-by-one that leads to reading the follow-up garbage
parameter length of 12336, and thus throwing an skb_over_panic
for the reply when trying to sctp_addto_chunk() next time,
which implicitly calls the skb_put() with that length.
Fix it by using sctp_walk_params() [ which is also used in
INIT parameter processing ] macro in the verification *and*
in ASCONF processing: it will make sure we don't spill over,
that we walk parameters WORD_ROUND()'ed. Moreover, we're being
more defensive and guard against unknown parameter types and
missized addresses.
Joint work with Vlad Yasevich.
Fixes: b896b82be4ae ("[SCTP] ADDIP: Support for processing incoming ASCONF_ACK chunks.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu updates from Tejun Heo:
"A lot of activities on percpu front. Notable changes are...
- percpu allocator now can take @gfp. If @gfp doesn't contain
GFP_KERNEL, it tries to allocate from what's already available to
the allocator and a work item tries to keep the reserve around
certain level so that these atomic allocations usually succeed.
This will replace the ad-hoc percpu memory pool used by
blk-throttle and also be used by the planned blkcg support for
writeback IOs.
Please note that I noticed a bug in how @gfp is interpreted while
preparing this pull request and applied the fix 6ae833c7fe
("percpu: fix how @gfp is interpreted by the percpu allocator")
just now.
- percpu_ref now uses longs for percpu and global counters instead of
ints. It leads to more sparse packing of the percpu counters on
64bit machines but the overhead should be negligible and this
allows using percpu_ref for refcnting pages and in-memory objects
directly.
- The switching between percpu and single counter modes of a
percpu_ref is made independent of putting the base ref and a
percpu_ref can now optionally be initialized in single or killed
mode. This allows avoiding percpu shutdown latency for cases where
the refcounted objects may be synchronously created and destroyed
in rapid succession with only a fraction of them reaching fully
operational status (SCSI probing does this when combined with
blk-mq support). It's also planned to be used to implement forced
single mode to detect underflow more timely for debugging.
There's a separate branch percpu/for-3.18-consistent-ops which cleans
up the duplicate percpu accessors. That branch causes a number of
conflicts with s390 and other trees. I'll send a separate pull
request w/ resolutions once other branches are merged"
* 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (33 commits)
percpu: fix how @gfp is interpreted by the percpu allocator
blk-mq, percpu_ref: start q->mq_usage_counter in atomic mode
percpu_ref: make INIT_ATOMIC and switch_to_atomic() sticky
percpu_ref: add PERCPU_REF_INIT_* flags
percpu_ref: decouple switching to percpu mode and reinit
percpu_ref: decouple switching to atomic mode and killing
percpu_ref: add PCPU_REF_DEAD
percpu_ref: rename things to prepare for decoupling percpu/atomic mode switch
percpu_ref: replace pcpu_ prefix with percpu_
percpu_ref: minor code and comment updates
percpu_ref: relocate percpu_ref_reinit()
Revert "blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe"
Revert "percpu: free percpu allocation info for uniprocessor system"
percpu-refcount: make percpu_ref based on longs instead of ints
percpu-refcount: improve WARN messages
percpu: fix locking regression in the failure path of pcpu_alloc()
percpu-refcount: add @gfp to percpu_ref_init()
proportions: add @gfp to init functions
percpu_counter: add @gfp to percpu_counter_init()
percpu_counter: make percpu_counters_lock irq-safe
...
Currently association restarts do not take into consideration the
state of the socket. When a restart happens, the current assocation
simply transitions into established state. This creates a condition
where a remote system, through a the restart procedure, may create a
local association that is no way reachable by user. The conditions
to trigger this are as follows:
1) Remote does not acknoledge some data causing data to remain
outstanding.
2) Local application calls close() on the socket. Since data
is still outstanding, the association is placed in SHUTDOWN_PENDING
state. However, the socket is closed.
3) The remote tries to create a new association, triggering a restart
on the local system. The association moves from SHUTDOWN_PENDING
to ESTABLISHED. At this point, it is no longer reachable by
any socket on the local system.
This patch addresses the above situation by moving the newly ESTABLISHED
association into SHUTDOWN-SENT state and bundling a SHUTDOWN after
the COOKIE-ACK chunk. This way, the restarted associate immidiately
enters the shutdown procedure and forces the termination of the
unreachable association.
Reported-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to receive 0a30288da1 ("blk-mq, percpu_ref: implement a
kludge for SCSI blk-mq stall during probe") which implements
__percpu_ref_kill_expedited() to work around SCSI blk-mq stall. The
commit reverted and patches to implement proper fix will be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
net.ipv4.ip_nonlocal_bind sysctl was global to all network
namespaces. This patch allows to set a different value for each
network namespace.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Percpu allocator now supports allocation mask. Add @gfp to
percpu_counter_init() so that !GFP_KERNEL allocation masks can be used
with percpu_counters too.
We could have left percpu_counter_init() alone and added
percpu_counter_init_gfp(); however, the number of users isn't that
high and introducing _gfp variants to all percpu data structures would
be quite ugly, so let's just do the conversion. This is the one with
the most users. Other percpu data structures are a lot easier to
convert.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: x86@kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
CHECKSUM_UNNECESSARY may be applied to the SCTP CRC so we need to
appropriate account for this by decrementing csum_level. This is
done by calling __skb_dec_checksum_unnecessary.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since SCTP day 1, that is, 19b55a2af145 ("Initial commit") from lksctp
tree, the official <netinet/sctp.h> header carries a copy of enum
sctp_sstat_state that looks like (compared to the current in-kernel
enumeration):
User definition: Kernel definition:
enum sctp_sstat_state { typedef enum {
SCTP_EMPTY = 0, <removed>
SCTP_CLOSED = 1, SCTP_STATE_CLOSED = 0,
SCTP_COOKIE_WAIT = 2, SCTP_STATE_COOKIE_WAIT = 1,
SCTP_COOKIE_ECHOED = 3, SCTP_STATE_COOKIE_ECHOED = 2,
SCTP_ESTABLISHED = 4, SCTP_STATE_ESTABLISHED = 3,
SCTP_SHUTDOWN_PENDING = 5, SCTP_STATE_SHUTDOWN_PENDING = 4,
SCTP_SHUTDOWN_SENT = 6, SCTP_STATE_SHUTDOWN_SENT = 5,
SCTP_SHUTDOWN_RECEIVED = 7, SCTP_STATE_SHUTDOWN_RECEIVED = 6,
SCTP_SHUTDOWN_ACK_SENT = 8, SCTP_STATE_SHUTDOWN_ACK_SENT = 7,
}; } sctp_state_t;
This header was later on also placed into the uapi, so that user space
programs can compile without having <netinet/sctp.h>, but the shipped
with <linux/sctp.h> instead.
While RFC6458 under 8.2.1.Association Status (SCTP_STATUS) says that
sstat_state can range from SCTP_CLOSED to SCTP_SHUTDOWN_ACK_SENT, we
nevertheless have a what it appears to be dummy SCTP_EMPTY state from
the very early days.
While it seems to do just nothing, commit 0b8f9e25b0 ("sctp: remove
completely unsed EMPTY state") did the right thing and removed this dead
code. That however, causes an off-by-one when the user asks the SCTP
stack via SCTP_STATUS API and checks for the current socket state thus
yielding possibly undefined behaviour in applications as they expect
the kernel to tell the right thing.
The enumeration had to be changed however as based on the current socket
state, we access a function pointer lookup-table through this. Therefore,
I think the best way to deal with this is just to add a helper function
sctp_assoc_to_state() to encapsulate the off-by-one quirk.
Reported-by: Tristan Su <sooqing@gmail.com>
Fixes: 0b8f9e25b0 ("sctp: remove completely unsed EMPTY state")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().
Commits 4c47af4d5e ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4dd5 ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.
Currently, the selection algorithm for T.ACT and T.RET is as follows:
1) Elect the two most recently used ACTIVE transports T1, T2 for
T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI
Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:
Setup:
<A> <B>
T1: p1p1 (10.0.10.10) <==> .'`) <==> p1p1 (10.0.10.12) <= T.PRI
T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)
net.sctp.rto_min = 1000
net.sctp.path_max_retrans = 2
net.sctp.pf_retrans = 0
net.sctp.hb_interval = 1000
T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.
After the patch, it's choosing better transports in both cases by
modifying step 4):
4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
the most recently used (if avail) in PF, set T.RET<-T.ACT_new
This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.
In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.
Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.
In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().
Now both tests work fine:
Case 1:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(ACTIVE) T.ACT, T.RET
T2 S(PF)
3. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
5. T1 S(PF) T.ACT, T.RET
T2 S(INACTIVE)
[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
T2 S(INACTIVE) ]
6. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Case 2:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(PF)
T2 S(ACTIVE) T.ACT, T.RET
3. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
5. T1 S(INACTIVE)
T2 S(PF) T.ACT, T.RET
[ 5.1 T1 S(INACTIVE)
T2 S(INACTIVE) T.ACT, T.RET ]
6. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the transport has always been in state SCTP_UNCONFIRMED, it
therefore wasn't active before and hasn't been used before, and it
always has been, so it is unnecessary to bug the user with a
notification.
Reported-by: Deepak Khandelwal <khandelwal.deepak.1987@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <tuexen@fh-muenster.de>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with ICMPv[46] Error Message, function icmp_socket_deliver()
and icmpv6_notify() do some valid checks on packet's length, but then some
protocols check packet's length redaudantly. So remove those duplicated
statements, and increase counter ICMP_MIB_INERRORS/ICMP6_MIB_INERRORS in
function icmp_socket_deliver() and icmpv6_notify() respectively.
In addition, add missed counter in udp6/udplite6 when socket is NULL.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP socket extensions API document describes the v4mapping option as
follows:
8.1.15. Set/Clear IPv4 Mapped Addresses (SCTP_I_WANT_MAPPED_V4_ADDR)
This socket option is a Boolean flag which turns on or off the
mapping of IPv4 addresses. If this option is turned on, then IPv4
addresses will be mapped to V6 representation. If this option is
turned off, then no mapping will be done of V4 addresses and a user
will receive both PF_INET6 and PF_INET type addresses on the socket.
See [RFC3542] for more details on mapped V6 addresses.
This description isn't really in line with what the code does though.
Introduce addr_to_user (renamed addr_v4map), which should be called
before any sockaddr is passed back to user space. The new function
places the sockaddr into the correct format depending on the
SCTP_I_WANT_MAPPED_V4_ADDR option.
Audit all places that touched v4mapped and either sanely construct
a v4 or v6 address then call addr_to_user, or drop the
unnecessary v4mapped check entirely.
Audit all places that call addr_to_user and verify they are on a sycall
return path.
Add a custom getname that formats the address properly.
Several bugs are addressed:
- SCTP_I_WANT_MAPPED_V4_ADDR=0 often returned garbage for
addresses to user space
- The addr_len returned from recvmsg was not correct when
returning AF_INET on a v6 socket
- flowlabel and scope_id were not zerod when promoting
a v4 to v6
- Some syscalls like bind and connect behaved differently
depending on v4mapped
Tested bind, getpeername, getsockname, connect, and recvmsg for proper
behaviour in v4mapped = 1 and 0 cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason reported an oops caused by SCTP on his ARM machine with
SCTP authentication enabled:
Internal error: Oops: 17 [#1] ARM
CPU: 0 PID: 104 Comm: sctp-test Not tainted 3.13.0-68744-g3632f30c9b20-dirty #1
task: c6eefa40 ti: c6f52000 task.ti: c6f52000
PC is at sctp_auth_calculate_hmac+0xc4/0x10c
LR is at sg_init_table+0x20/0x38
pc : [<c024bb80>] lr : [<c00f32dc>] psr: 40000013
sp : c6f538e8 ip : 00000000 fp : c6f53924
r10: c6f50d80 r9 : 00000000 r8 : 00010000
r7 : 00000000 r6 : c7be4000 r5 : 00000000 r4 : c6f56254
r3 : c00c8170 r2 : 00000001 r1 : 00000008 r0 : c6f1e660
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005397f Table: 06f28000 DAC: 00000015
Process sctp-test (pid: 104, stack limit = 0xc6f521c0)
Stack: (0xc6f538e8 to 0xc6f54000)
[...]
Backtrace:
[<c024babc>] (sctp_auth_calculate_hmac+0x0/0x10c) from [<c0249af8>] (sctp_packet_transmit+0x33c/0x5c8)
[<c02497bc>] (sctp_packet_transmit+0x0/0x5c8) from [<c023e96c>] (sctp_outq_flush+0x7fc/0x844)
[<c023e170>] (sctp_outq_flush+0x0/0x844) from [<c023ef78>] (sctp_outq_uncork+0x24/0x28)
[<c023ef54>] (sctp_outq_uncork+0x0/0x28) from [<c0234364>] (sctp_side_effects+0x1134/0x1220)
[<c0233230>] (sctp_side_effects+0x0/0x1220) from [<c02330b0>] (sctp_do_sm+0xac/0xd4)
[<c0233004>] (sctp_do_sm+0x0/0xd4) from [<c023675c>] (sctp_assoc_bh_rcv+0x118/0x160)
[<c0236644>] (sctp_assoc_bh_rcv+0x0/0x160) from [<c023d5bc>] (sctp_inq_push+0x6c/0x74)
[<c023d550>] (sctp_inq_push+0x0/0x74) from [<c024a6b0>] (sctp_rcv+0x7d8/0x888)
While we already had various kind of bugs in that area
ec0223ec48 ("net: sctp: fix sctp_sf_do_5_1D_ce to verify if
we/peer is AUTH capable") and b14878ccb7 ("net: sctp: cache
auth_enable per endpoint"), this one is a bit of a different
kind.
Giving a bit more background on why SCTP authentication is
needed can be found in RFC4895:
SCTP uses 32-bit verification tags to protect itself against
blind attackers. These values are not changed during the
lifetime of an SCTP association.
Looking at new SCTP extensions, there is the need to have a
method of proving that an SCTP chunk(s) was really sent by
the original peer that started the association and not by a
malicious attacker.
To cause this bug, we're triggering an INIT collision between
peers; normal SCTP handshake where both sides intent to
authenticate packets contains RANDOM; CHUNKS; HMAC-ALGO
parameters that are being negotiated among peers:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
RFC4895 says that each endpoint therefore knows its own random
number and the peer's random number *after* the association
has been established. The local and peer's random number along
with the shared key are then part of the secret used for
calculating the HMAC in the AUTH chunk.
Now, in our scenario, we have 2 threads with 1 non-blocking
SEQ_PACKET socket each, setting up common shared SCTP_AUTH_KEY
and SCTP_AUTH_ACTIVE_KEY properly, and each of them calling
sctp_bindx(3), listen(2) and connect(2) against each other,
thus the handshake looks similar to this, e.g.:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
<--------- INIT[RANDOM; CHUNKS; HMAC-ALGO] -----------
-------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] -------->
...
Since such collisions can also happen with verification tags,
the RFC4895 for AUTH rather vaguely says under section 6.1:
In case of INIT collision, the rules governing the handling
of this Random Number follow the same pattern as those for
the Verification Tag, as explained in Section 5.2.4 of
RFC 2960 [5]. Therefore, each endpoint knows its own Random
Number and the peer's Random Number after the association
has been established.
In RFC2960, section 5.2.4, we're eventually hitting Action B:
B) In this case, both sides may be attempting to start an
association at about the same time but the peer endpoint
started its INIT after responding to the local endpoint's
INIT. Thus it may have picked a new Verification Tag not
being aware of the previous Tag it had sent this endpoint.
The endpoint should stay in or enter the ESTABLISHED
state but it MUST update its peer's Verification Tag from
the State Cookie, stop any init or cookie timers that may
running and send a COOKIE ACK.
In other words, the handling of the Random parameter is the
same as behavior for the Verification Tag as described in
Action B of section 5.2.4.
Looking at the code, we exactly hit the sctp_sf_do_dupcook_b()
case which triggers an SCTP_CMD_UPDATE_ASSOC command to the
side effect interpreter, and in fact it properly copies over
peer_{random, hmacs, chunks} parameters from the newly created
association to update the existing one.
Also, the old asoc_shared_key is being released and based on
the new params, sctp_auth_asoc_init_active_key() updated.
However, the issue observed in this case is that the previous
asoc->peer.auth_capable was 0, and has *not* been updated, so
that instead of creating a new secret, we're doing an early
return from the function sctp_auth_asoc_init_active_key()
leaving asoc->asoc_shared_key as NULL. However, we now have to
authenticate chunks from the updated chunk list (e.g. COOKIE-ACK).
That in fact causes the server side when responding with ...
<------------------ AUTH; COOKIE-ACK -----------------
... to trigger a NULL pointer dereference, since in
sctp_packet_transmit(), it discovers that an AUTH chunk is
being queued for xmit, and thus it calls sctp_auth_calculate_hmac().
Since the asoc->active_key_id is still inherited from the
endpoint, and the same as encoded into the chunk, it uses
asoc->asoc_shared_key, which is still NULL, as an asoc_key
and dereferences it in ...
crypto_hash_setkey(desc.tfm, &asoc_key->data[0], asoc_key->len)
... causing an oops. All this happens because sctp_make_cookie_ack()
called with the *new* association has the peer.auth_capable=1
and therefore marks the chunk with auth=1 after checking
sctp_auth_send_cid(), but it is *actually* sent later on over
the then *updated* association's transport that didn't initialize
its shared key due to peer.auth_capable=0. Since control chunks
in that case are not sent by the temporary association which
are scheduled for deletion, they are issued for xmit via
SCTP_CMD_REPLY in the interpreter with the context of the
*updated* association. peer.auth_capable was 0 in the updated
association (which went from COOKIE_WAIT into ESTABLISHED state),
since all previous processing that performed sctp_process_init()
was being done on temporary associations, that we eventually
throw away each time.
The correct fix is to update to the new peer.auth_capable
value as well in the collision case via sctp_assoc_update(),
so that in case the collision migrated from 0 -> 1,
sctp_auth_asoc_init_active_key() can properly recalculate
the secret. This therefore fixes the observed server panic.
Fixes: 730fc3d05c ("[SCTP]: Implete SCTP-AUTH parameter processing")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSG_MORE and 'corking' a socket would require that the transmit of
a data chunk be delayed.
Rename the return value to be less specific.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for Nagle contains 6 separate checks all of which must be true
before a data packet is delayed.
Separate out each into its own 'if (test) return SCTP_XMIT_OK' so that
the reasons can be individually described.
Also return directly with SCTP_XMIT_RWND_FULL.
Delete the now-unused 'retval' variable and 'finish' label from
sctp_packet_can_append_data().
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With support of SCTP_SNDINFO/SCTP_RCVINFO as described in RFC6458,
5.3.4/5.3.5, we can now deprecate SCTP_SNDRCV. The RFC already
declares it as deprecated:
This structure mixes the send and receive path. SCTP_SNDINFO
(described in Section 5.3.4) and SCTP_RCVINFO (described in
Section 5.3.5) split this information. These structures should
be used, when possible, since SCTP_SNDRCV is deprecated.
So whenever a user tries to subscribe to sctp_data_io_event via
setsockopt(2) which triggers inclusion of SCTP_SNDRCV cmsg_type,
issue a warning in the log.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements section 8.1.31. of RFC6458, which adds support
for setting/retrieving SCTP_DEFAULT_SNDINFO:
Applications that wish to use the sendto() system call may wish
to specify a default set of parameters that would normally be
supplied through the inclusion of ancillary data. This socket
option allows such an application to set the default sctp_sndinfo
structure. The application that wishes to use this socket option
simply passes the sctp_sndinfo structure (defined in Section 5.3.4)
to this call. The input parameters accepted by this call include
snd_sid, snd_flags, snd_ppid, and snd_context. The snd_flags
parameter is composed of a bitwise OR of SCTP_UNORDERED, SCTP_EOF,
and SCTP_SENDALL. The snd_assoc_id field specifies the association
to which to apply the parameters. For a one-to-many style socket,
any of the predefined constants are also allowed in this field.
The field is ignored for one-to-one style sockets.
Joint work with Daniel Borkmann.
Signed-off-by: Geir Ola Vaagland <geirola@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements section 5.3.6. of RFC6458, that is, support
for 'SCTP Next Receive Information Structure' (SCTP_NXTINFO) which
is placed into ancillary data cmsghdr structure for each recvmsg()
call, if this information is already available when delivering the
current message.
This option can be enabled/disabled via setsockopt(2) on SOL_SCTP
level by setting an int value with 1/0 for SCTP_RECVNXTINFO in
user space applications as per RFC6458, section 8.1.30.
The sctp_nxtinfo structure is defined as per RFC as below ...
struct sctp_nxtinfo {
uint16_t nxt_sid;
uint16_t nxt_flags;
uint32_t nxt_ppid;
uint32_t nxt_length;
sctp_assoc_t nxt_assoc_id;
};
... and provided under cmsg_level IPPROTO_SCTP, cmsg_type
SCTP_NXTINFO, while cmsg_data[] contains struct sctp_nxtinfo.
Joint work with Daniel Borkmann.
Signed-off-by: Geir Ola Vaagland <geirola@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements section 5.3.5. of RFC6458, that is, support
for 'SCTP Receive Information Structure' (SCTP_RCVINFO) which is
placed into ancillary data cmsghdr structure for each recvmsg()
call.
This option can be enabled/disabled via setsockopt(2) on SOL_SCTP
level by setting an int value with 1/0 for SCTP_RECVRCVINFO in user
space applications as per RFC6458, section 8.1.29.
The sctp_rcvinfo structure is defined as per RFC as below ...
struct sctp_rcvinfo {
uint16_t rcv_sid;
uint16_t rcv_ssn;
uint16_t rcv_flags;
<-- 2 bytes hole -->
uint32_t rcv_ppid;
uint32_t rcv_tsn;
uint32_t rcv_cumtsn;
uint32_t rcv_context;
sctp_assoc_t rcv_assoc_id;
};
... and provided under cmsg_level IPPROTO_SCTP, cmsg_type
SCTP_RCVINFO, while cmsg_data[] contains struct sctp_rcvinfo.
An sctp_rcvinfo item always corresponds to the data in msg_iov.
Joint work with Daniel Borkmann.
Signed-off-by: Geir Ola Vaagland <geirola@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements section 5.3.4. of RFC6458, that is, support
for 'SCTP Send Information Structure' (SCTP_SNDINFO) which can be
placed into ancillary data cmsghdr structure for sendmsg() calls.
The sctp_sndinfo structure is defined as per RFC as below ...
struct sctp_sndinfo {
uint16_t snd_sid;
uint16_t snd_flags;
uint32_t snd_ppid;
uint32_t snd_context;
sctp_assoc_t snd_assoc_id;
};
... and supplied under cmsg_level IPPROTO_SCTP, cmsg_type
SCTP_SNDINFO, while cmsg_data[] contains struct sctp_sndinfo.
An sctp_sndinfo item always corresponds to the data in msg_iov.
Joint work with Daniel Borkmann.
Signed-off-by: Geir Ola Vaagland <geirola@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on some other SCTP code, I noticed that some
structures shared with user space are leaking uninitialized
stack or heap buffer. In particular, struct sctp_sndrcvinfo
has a 2 bytes hole between .sinfo_flags and .sinfo_ppid that
remains unfilled by us in sctp_ulpevent_read_sndrcvinfo() when
putting this into cmsg. But also struct sctp_remote_error
contains a 2 bytes hole that we don't fill but place into a skb
through skb_copy_expand() via sctp_ulpevent_make_remote_error().
Both structures are defined by the IETF in RFC6458:
* Section 5.3.2. SCTP Header Information Structure:
The sctp_sndrcvinfo structure is defined below:
struct sctp_sndrcvinfo {
uint16_t sinfo_stream;
uint16_t sinfo_ssn;
uint16_t sinfo_flags;
<-- 2 bytes hole -->
uint32_t sinfo_ppid;
uint32_t sinfo_context;
uint32_t sinfo_timetolive;
uint32_t sinfo_tsn;
uint32_t sinfo_cumtsn;
sctp_assoc_t sinfo_assoc_id;
};
* 6.1.3. SCTP_REMOTE_ERROR:
A remote peer may send an Operation Error message to its peer.
This message indicates a variety of error conditions on an
association. The entire ERROR chunk as it appears on the wire
is included in an SCTP_REMOTE_ERROR event. Please refer to the
SCTP specification [RFC4960] and any extensions for a list of
possible error formats. An SCTP error notification has the
following format:
struct sctp_remote_error {
uint16_t sre_type;
uint16_t sre_flags;
uint32_t sre_length;
uint16_t sre_error;
<-- 2 bytes hole -->
sctp_assoc_t sre_assoc_id;
uint8_t sre_data[];
};
Fix this by setting both to 0 before filling them out. We also
have other structures shared between user and kernel space in
SCTP that contains holes (e.g. struct sctp_paddrthlds), but we
copy that buffer over from user space first and thus don't need
to care about it in that cases.
While at it, we can also remove lengthy comments copied from
the draft, instead, we update the comment with the correct RFC
number where one can look it up.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_init_cmd_seq() and sctp_next_cmd() are only called from one place.
The call sequence for sctp_add_cmd_sf() is likely to be longer than
the inlined code.
With sctp_add_cmd_sf() inlined the compiler can optimise repeated calls.
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only warn if the value is written to alpha or beta. We don't care
emitting a one-time warning when only reading it.
Reported-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4960, section 8.3 says:
On an idle destination address that is allowed to heartbeat,
it is recommended that a HEARTBEAT chunk is sent once per RTO
of that destination address plus the protocol parameter
'HB.interval', with jittering of +/- 50% of the RTO value,
and exponential backoff of the RTO if the previous HEARTBEAT
is unanswered.
Currently, we calculate jitter via sctp_jitter() function first,
and then add its result to the current RTO for the new timeout:
TMO = RTO + (RAND() % RTO) - (RTO / 2)
`------------------------^-=> sctp_jitter()
Instead, we can just simplify all this by directly calculating:
TMO = (RTO / 2) + (RAND() % RTO)
With the help of prandom_u32_max(), we don't need to open code
our own global PRNG, but can instead just make use of the per
CPU implementation of prandom with better quality numbers. Also,
we can now spare us the conditional for divide by zero check
since no div or mod operation needs to be used. Note that
prandom_u32_max() won't emit the same result as a mod operation,
but we really don't care here as we only want to have a random
number scaled into RTO interval.
Note, exponential RTO backoff is handeled elsewhere, namely in
sctp_do_8_2_transport_strike().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When writing to the sysctl field net.sctp.auth_enable, it can well
be that the user buffer we handed over to proc_dointvec() via
proc_sctp_do_auth() handler contains something other than integers.
In that case, we would set an uninitialized 4-byte value from the
stack to net->sctp.auth_enable that can be leaked back when reading
the sysctl variable, and it can unintentionally turn auth_enable
on/off based on the stack content since auth_enable is interpreted
as a boolean.
Fix it up by making sure proc_dointvec() returned sucessfully.
Fixes: b14878ccb7 ("net: sctp: cache auth_enable per endpoint")
Reported-by: Florian Westphal <fwestpha@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl handler proc_sctp_do_hmac_alg(), proc_sctp_do_rto_min() and
proc_sctp_do_rto_max() do not properly reflect some error cases
when writing values via sysctl from internal proc functions such
as proc_dointvec() and proc_dostring().
In all these cases we pass the test for write != 0 and partially
do additional work just to notice that additional sanity checks
fail and we return with hard-coded -EINVAL while proc_do*
functions might also return different errors. So fix this up by
simply testing a successful return of proc_do* right after
calling it.
This also allows to propagate its return value onwards to the user.
While touching this, also fix up some minor style issues.
Fixes: 4f3fdf3bc5 ("sctp: add check rto_min and rto_max in sysctl")
Fixes: 3c68198e75 ("sctp: Make hmac algorithm selection for cookie generation dynamic")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3fd091e73b ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|
and
SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the scenario:
For a TCP-style socket, while processing the COOKIE_ECHO chunk in
sctp_sf_do_5_1D_ce(), after it has passed a series of sanity check,
a new association would be created in sctp_unpack_cookie(), but afterwards,
some processing maybe failed, and sctp_association_free() will be called to
free the previously allocated association, in sctp_association_free(),
sk_ack_backlog value is decremented for this socket, since the initial
value for sk_ack_backlog is 0, after the decrement, it will be 65535,
a wrap-around problem happens, and if we want to establish new associations
afterward in the same socket, ABORT would be triggered since sctp deem the
accept queue as full.
Fix this issue by only decrementing sk_ack_backlog for associations in
the endpoint's list.
Fix-suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warning:
net/sctp/associola.c:1556:29: warning: incorrect type in initializer (different base types)
net/sctp/associola.c:1556:29: expected bool [unsigned] [usertype] preload
net/sctp/associola.c:1556:29: got restricted gfp_t
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function sctp_select_active_and_retran_path(), we walk the
transport list in order to look for the two most recently used
ACTIVE transports (trans_pri, trans_sec). In case we didn't find
anything ACTIVE, we currently just camp on a possibly PF or
INACTIVE transport that is primary path; this behavior actually
dates back to linux-history tree of the very early days of
lksctp, and can yield a behavior that chooses suboptimal
transport paths.
Instead, be a bit more clever by reusing and extending the
recently introduced sctp_trans_elect_best() handler. In case
both transports are evaluated to have the same score resulting
from their states, break the tie by looking at: 1) transport
patch error count 2) last_time_heard value from each transport.
This is analogous to Nishida's Quick Failover draft [1],
section 5.1, 3:
The sender SHOULD avoid data transmission to PF destinations.
When all destinations are in either PF or Inactive state,
the sender MAY either move the destination from PF to active
state (and transmit data to the active destination) or the
sender MAY transmit data to a PF destination. In the former
scenario, (i) the sender MUST NOT notify the ULP about the
state transition, and (ii) MUST NOT clear the destination's
error counter. It is recommended that the sender picks the
PF destination with least error count (fewest consecutive
timeouts) for data transmission. In case of a tie (multiple PF
destinations with same error count), the sender MAY choose the
last active destination.
Thus for sctp_select_active_and_retran_path(), we keep track of
the best, if any, transport that is in PF state and in case no
ACTIVE transport has been found (hence trans_{pri,sec} is NULL),
we select the best out of the three: current primary_path and
retran_path as well as a possible PF transport.
The secondary may still camp on the original primary_path as
before. The change in sctp_trans_elect_best() with a more fine
grained tie selection also improves at the same time path selection
for sctp_assoc_update_retran_path() in case of non-ACTIVE states.
[1] http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more precise in transport path selection and use ktime
helpers instead of jiffies to compare and pick the better
primary and secondary recently used transports. This also
avoids any side-effects during a possible roll-over, and
could lead to better path decision-making.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just refactors and moves the code for the active
path selection into its own helper function outside of
sctp_assoc_control_transport() which is already big enough.
No functional changes here.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two minimal helper functions analogous to time_before() and
time_after() that will later on both be needed by SCTP code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define separate fields in the sock structure for configuring disabling
checksums in both TX and RX-- sk_no_check_tx and sk_no_check_rx.
The SO_NO_CHECK socket option only affects sk_no_check_tx. Also,
removed UDP_CSUM_* defines since they are no longer necessary.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang reported the following sparse warning:
>> net/ipv6/proc.c:198:41: sparse: incorrect type in argument 1 (different address spaces)
net/ipv6/proc.c:198:41: expected void [noderef] <asn:3>*mib
net/ipv6/proc.c:198:41: got void [noderef] <asn:3>**pcpumib
Fixes: commit 698365fa18 (net: clean up snmp stats code)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_local_port_range is already per netns, so should ip_local_reserved_ports
be. And since it is none by default we don't actually need it when we don't
enable CONFIG_SYSCTL.
By the way, rename inet_is_reserved_local_port() to inet_is_local_reserved_port()
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by several people, rename local_df to ignore_df,
since it means "ignore df bit if it is set".
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When register_net_sysctl failed, we should free the
sysctl_table.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8f0ea0fe3a (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:
commit 933393f58f
Date: Thu Dec 22 11:58:51 2011 -0600
percpu: Remove irqsafe_cpu_xxx variants
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.
So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.
Cc: Christoph Lameter <cl@linux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't transition to the PF state on every strike after 'Path.Max.Retrans'.
Per draft-ietf-tsvwg-sctp-failover-03 Section 5.1.6:
Additional (PMR - PFMR) consecutive timeouts on a PF destination
confirm the path failure, upon which the destination transitions to the
Inactive state. As described in [RFC4960], the sender (i) SHOULD notify
ULP about this state transition, and (ii) transmit heartbeats to the
Inactive destination at a lower frequency as described in Section 8.3 of
[RFC4960].
This also prevents sending SCTP_ADDR_UNREACHABLE to the user as the state
bounces between SCTP_INACTIVE and SCTP_PF for each subsequent strike.
Signed-off-by: Karl Heiss <kheiss@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 813b3b5db8 (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241c (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.
To reproduce this problem, a vlan setting is enough:
# ifconfig eth0 up
# route del default
# vconfig add eth0 2
# vconfig add eth0 3
# ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
# route add default gw 10.0.1.254 dev eth0.2
# ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
# ip rule add from 10.0.0.14 table 4
# ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
# sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The busy polling socket option adds support for sockets to busy wait on data
arriving on the napi queue from which they have most recently received a frame.
Currently only tcp and udp support this feature, but theres no reason sctp can't
do so as well. Add it in so appliations can take advantage of it
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Daniel Borkmann <dborkman@redhat.com>
CC: netdev@vger.kernel.org
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is possible to create an SCTP socket, then switch
auth_enable via sysctl setting to 1 and crash the system on connect:
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.14.1-mipsgit-20140415 #1
task: ffffffff8056ce80 ti: ffffffff8055c000 task.ti: ffffffff8055c000
[...]
Call Trace:
[<ffffffff8043c4e8>] sctp_auth_asoc_set_default_hmac+0x68/0x80
[<ffffffff8042b300>] sctp_process_init+0x5e0/0x8a4
[<ffffffff8042188c>] sctp_sf_do_5_1B_init+0x234/0x34c
[<ffffffff804228c8>] sctp_do_sm+0xb4/0x1e8
[<ffffffff80425a08>] sctp_endpoint_bh_rcv+0x1c4/0x214
[<ffffffff8043af68>] sctp_rcv+0x588/0x630
[<ffffffff8043e8e8>] sctp6_rcv+0x10/0x24
[<ffffffff803acb50>] ip6_input+0x2c0/0x440
[<ffffffff8030fc00>] __netif_receive_skb_core+0x4a8/0x564
[<ffffffff80310650>] process_backlog+0xb4/0x18c
[<ffffffff80313cbc>] net_rx_action+0x12c/0x210
[<ffffffff80034254>] __do_softirq+0x17c/0x2ac
[<ffffffff800345e0>] irq_exit+0x54/0xb0
[<ffffffff800075a4>] ret_from_irq+0x0/0x4
[<ffffffff800090ec>] rm7k_wait_irqoff+0x24/0x48
[<ffffffff8005e388>] cpu_startup_entry+0xc0/0x148
[<ffffffff805a88b0>] start_kernel+0x37c/0x398
Code: dd0900b8 000330f8 0126302d <dcc60000> 50c0fff1 0047182a a48306a0
03e00008 00000000
---[ end trace b530b0551467f2fd ]---
Kernel panic - not syncing: Fatal exception in interrupt
What happens while auth_enable=0 in that case is, that
ep->auth_hmacs is initialized to NULL in sctp_auth_init_hmacs()
when endpoint is being created.
After that point, if an admin switches over to auth_enable=1,
the machine can crash due to NULL pointer dereference during
reception of an INIT chunk. When we enter sctp_process_init()
via sctp_sf_do_5_1B_init() in order to respond to an INIT chunk,
the INIT verification succeeds and while we walk and process
all INIT params via sctp_process_param() we find that
net->sctp.auth_enable is set, therefore do not fall through,
but invoke sctp_auth_asoc_set_default_hmac() instead, and thus,
dereference what we have set to NULL during endpoint
initialization phase.
The fix is to make auth_enable immutable by caching its value
during endpoint initialization, so that its original value is
being carried along until destruction. The bug seems to originate
from the very first days.
Fix in joint work with Daniel Borkmann.
Reported-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956 ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.
One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.
Fixes: 31c70d5956 ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu <nasa4836@gmail.com>
Tested-by: Zhan Jianyu <nasa4836@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
In function sctp_wake_up_waiters(), we need to involve a test
if the association is declared dead. If so, we don't have any
reference to a possible sibling association anymore and need
to invoke sctp_write_space() instead, and normally walk the
socket's associations and notify them of new wmem space. The
reason for special casing is that otherwise, we could run
into the following issue when a sctp_primitive_SEND() call
from sctp_sendmsg() fails, and tries to flush an association's
outq, i.e. in the following way:
sctp_association_free()
`-> list_del(&asoc->asocs) <-- poisons list pointer
asoc->base.dead = true
sctp_outq_free(&asoc->outqueue)
`-> __sctp_outq_teardown()
`-> sctp_chunk_free()
`-> consume_skb()
`-> sctp_wfree()
`-> sctp_wake_up_waiters() <-- dereferences poisoned pointers
if asoc->ep->sndbuf_policy=0
Therefore, only walk the list in an 'optimized' way if we find
that the current association is still active. We could also use
list_del_init() in addition when we call sctp_association_free(),
but as Vlad suggests, we want to trap such bugs and thus leave
it poisoned as is.
Why is it safe to resolve the issue by testing for asoc->base.dead?
Parallel calls to sctp_sendmsg() are protected under socket lock,
that is lock_sock()/release_sock(). Only within that path under
lock held, we're setting skb/chunk owner via sctp_set_owner_w().
Eventually, chunks are freed directly by an association still
under that lock. So when traversing association list on destruction
time from sctp_wake_up_waiters() via sctp_wfree(), a different
CPU can't be running sctp_wfree() while another one calls
sctp_association_free() as both happens under the same lock.
Therefore, this can also not race with setting/testing against
asoc->base.dead as we are guaranteed for this to happen in order,
under lock. Further, Vlad says: the times we check asoc->base.dead
is when we've cached an association pointer for later processing.
In between cache and processing, the association may have been
freed and is simply still around due to reference counts. We check
asoc->base.dead under a lock, so it should always be safe to check
and not race against sctp_association_free(). Stress-testing seems
fine now, too.
Fixes: cd253f9f357d ("net: sctp: wake up all assocs if sndbuf policy is per socket")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP charges chunks for wmem accounting via skb->truesize in
sctp_set_owner_w(), and sctp_wfree() respectively as the
reverse operation. If a sender runs out of wmem, it needs to
wait via sctp_wait_for_sndbuf(), and gets woken up by a call
to __sctp_write_space() mostly via sctp_wfree().
__sctp_write_space() is being called per association. Although
we assign sk->sk_write_space() to sctp_write_space(), which
is then being done per socket, it is only used if send space
is increased per socket option (SO_SNDBUF), as SOCK_USE_WRITE_QUEUE
is set and therefore not invoked in sock_wfree().
Commit 4c3a5bdae2 ("sctp: Don't charge for data in sndbuf
again when transmitting packet") fixed an issue where in case
sctp_packet_transmit() manages to queue up more than sndbuf
bytes, sctp_wait_for_sndbuf() will never be woken up again
unless it is interrupted by a signal. However, a still
remaining issue is that if net.sctp.sndbuf_policy=0, that is
accounting per socket, and one-to-many sockets are in use,
the reclaimed write space from sctp_wfree() is 'unfairly'
handed back on the server to the association that is the lucky
one to be woken up again via __sctp_write_space(), while
the remaining associations are never be woken up again
(unless by a signal).
The effect disappears with net.sctp.sndbuf_policy=1, that
is wmem accounting per association, as it guarantees a fair
share of wmem among associations.
Therefore, if we have reclaimed memory in case of per socket
accounting, wake all related associations to a socket in a
fair manner, that is, traverse the socket association list
starting from the current neighbour of the association and
issue a __sctp_write_space() to everyone until we end up
waking ourselves. This guarantees that no association is
preferred over another and even if more associations are
taken into the one-to-many session, all receivers will get
messages from the server and are not stalled forever on
high load. This setting still leaves the advantage of per
socket accounting in touch as an association can still use
up global limits if unused by others.
Fixes: 4eb701dfc6 ("[SCTP] Fix SCTP sendbuffer accouting.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is basically just to let Coverity et al shut up. Remove an
unneeded NULL check in sctp_assoc_update_retran_path().
It is safe to remove it, because in sctp_assoc_update_retran_path()
we iterate over the list of transports, our own transport which is
asoc->peer.retran_path included. In the iteration, we skip the
list head element and transports in state SCTP_UNCONFIRMED.
Such transports came from peer addresses received in INIT/INIT-ACK
address parameters. They are not yet confirmed by a heartbeat and
not available for data transfers.
We know however that in the list of transports, even if it contains
such elements, it at least contains our asoc->peer.retran_path as
well, so even if next to that element, we only encounter
SCTP_UNCONFIRMED transports, we are always going to fall back to
asoc->peer.retran_path through sctp_trans_elect_best(), as that is
for sure not SCTP_UNCONFIRMED as per fbdf501c93 ("sctp: Do no
select unconfirmed transports for retransmissions").
Whenever we call sctp_trans_elect_best() it will give us a non-NULL
element back, and therefore when we break out of the loop, we are
guaranteed to have a non-NULL transport pointer, and can remove
the NULL check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on ec0223ec48 ("net: sctp: fix sctp_sf_do_5_1D_ce to
verify if we/peer is AUTH capable"), we noticed that there's a skb
memory leakage in the error path.
Running the same reproducer as in ec0223ec48 and by unconditionally
jumping to the error label (to simulate an error condition) in
sctp_sf_do_5_1D_ce() receive path lets kmemleak detector bark about
the unfreed chunk->auth_chunk skb clone:
Unreferenced object 0xffff8800b8f3a000 (size 256):
comm "softirq", pid 0, jiffies 4294769856 (age 110.757s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
89 ab 75 5e d4 01 58 13 00 00 00 00 00 00 00 00 ..u^..X.........
backtrace:
[<ffffffff816660be>] kmemleak_alloc+0x4e/0xb0
[<ffffffff8119f328>] kmem_cache_alloc+0xc8/0x210
[<ffffffff81566929>] skb_clone+0x49/0xb0
[<ffffffffa0467459>] sctp_endpoint_bh_rcv+0x1d9/0x230 [sctp]
[<ffffffffa046fdbc>] sctp_inq_push+0x4c/0x70 [sctp]
[<ffffffffa047e8de>] sctp_rcv+0x82e/0x9a0 [sctp]
[<ffffffff815abd38>] ip_local_deliver_finish+0xa8/0x210
[<ffffffff815a64af>] nf_reinject+0xbf/0x180
[<ffffffffa04b4762>] nfqnl_recv_verdict+0x1d2/0x2b0 [nfnetlink_queue]
[<ffffffffa04aa40b>] nfnetlink_rcv_msg+0x14b/0x250 [nfnetlink]
[<ffffffff815a3269>] netlink_rcv_skb+0xa9/0xc0
[<ffffffffa04aa7cf>] nfnetlink_rcv+0x23f/0x408 [nfnetlink]
[<ffffffff815a2bd8>] netlink_unicast+0x168/0x250
[<ffffffff815a2fa1>] netlink_sendmsg+0x2e1/0x3f0
[<ffffffff8155cc6b>] sock_sendmsg+0x8b/0xc0
[<ffffffff8155d449>] ___sys_sendmsg+0x369/0x380
What happens is that commit bbd0d59809 clones the skb containing
the AUTH chunk in sctp_endpoint_bh_rcv() when having the edge case
that an endpoint requires COOKIE-ECHO chunks to be authenticated:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
------------------ AUTH; COOKIE-ECHO ---------------->
<-------------------- COOKIE-ACK ---------------------
When we enter sctp_sf_do_5_1D_ce() and before we actually get to
the point where we process (and subsequently free) a non-NULL
chunk->auth_chunk, we could hit the "goto nomem_init" path from
an error condition and thus leave the cloned skb around w/o
freeing it.
The fix is to centrally free such clones in sctp_chunk_destroy()
handler that is invoked from sctp_chunk_free() after all refs have
dropped; and also move both kfree_skb(chunk->auth_chunk) there,
so that chunk->auth_chunk is either NULL (since sctp_chunkify()
allocs new chunks through kmem_cache_zalloc()) or non-NULL with
a valid skb pointer. chunk->skb and chunk->auth_chunk are the
only skbs in the sctp_chunk structure that need to be handeled.
While at it, we should use consume_skb() for both. It is the same
as dev_kfree_skb() but more appropriately named as we are not
a device but a protocol. Also, this effectively replaces the
kfree_skb() from both invocations into consume_skb(). Functions
are the same only that kfree_skb() assumes that the frame was
being dropped after a failure (e.g. for tools like drop monitor),
usage of consume_skb() seems more appropriate in function
sctp_chunk_destroy() though.
Fixes: bbd0d59809 ("[SCTP]: Implement the receive and verification of AUTH chunk")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <yasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4895 introduced AUTH chunks for SCTP; during the SCTP
handshake RANDOM; CHUNKS; HMAC-ALGO are negotiated (CHUNKS
being optional though):
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
-------------------- COOKIE-ECHO -------------------->
<-------------------- COOKIE-ACK ---------------------
A special case is when an endpoint requires COOKIE-ECHO
chunks to be authenticated:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
------------------ AUTH; COOKIE-ECHO ---------------->
<-------------------- COOKIE-ACK ---------------------
RFC4895, section 6.3. Receiving Authenticated Chunks says:
The receiver MUST use the HMAC algorithm indicated in
the HMAC Identifier field. If this algorithm was not
specified by the receiver in the HMAC-ALGO parameter in
the INIT or INIT-ACK chunk during association setup, the
AUTH chunk and all the chunks after it MUST be discarded
and an ERROR chunk SHOULD be sent with the error cause
defined in Section 4.1. [...] If no endpoint pair shared
key has been configured for that Shared Key Identifier,
all authenticated chunks MUST be silently discarded. [...]
When an endpoint requires COOKIE-ECHO chunks to be
authenticated, some special procedures have to be followed
because the reception of a COOKIE-ECHO chunk might result
in the creation of an SCTP association. If a packet arrives
containing an AUTH chunk as a first chunk, a COOKIE-ECHO
chunk as the second chunk, and possibly more chunks after
them, and the receiver does not have an STCB for that
packet, then authentication is based on the contents of
the COOKIE-ECHO chunk. In this situation, the receiver MUST
authenticate the chunks in the packet by using the RANDOM
parameters, CHUNKS parameters and HMAC_ALGO parameters
obtained from the COOKIE-ECHO chunk, and possibly a local
shared secret as inputs to the authentication procedure
specified in Section 6.3. If authentication fails, then
the packet is discarded. If the authentication is successful,
the COOKIE-ECHO and all the chunks after the COOKIE-ECHO
MUST be processed. If the receiver has an STCB, it MUST
process the AUTH chunk as described above using the STCB
from the existing association to authenticate the
COOKIE-ECHO chunk and all the chunks after it. [...]
Commit bbd0d59809 introduced the possibility to receive
and verification of AUTH chunk, including the edge case for
authenticated COOKIE-ECHO. On reception of COOKIE-ECHO,
the function sctp_sf_do_5_1D_ce() handles processing,
unpacks and creates a new association if it passed sanity
checks and also tests for authentication chunks being
present. After a new association has been processed, it
invokes sctp_process_init() on the new association and
walks through the parameter list it received from the INIT
chunk. It checks SCTP_PARAM_RANDOM, SCTP_PARAM_HMAC_ALGO
and SCTP_PARAM_CHUNKS, and copies them into asoc->peer
meta data (peer_random, peer_hmacs, peer_chunks) in case
sysctl -w net.sctp.auth_enable=1 is set. If in INIT's
SCTP_PARAM_SUPPORTED_EXT parameter SCTP_CID_AUTH is set,
peer_random != NULL and peer_hmacs != NULL the peer is to be
assumed asoc->peer.auth_capable=1, in any other case
asoc->peer.auth_capable=0.
Now, if in sctp_sf_do_5_1D_ce() chunk->auth_chunk is
available, we set up a fake auth chunk and pass that on to
sctp_sf_authenticate(), which at latest in
sctp_auth_calculate_hmac() reliably dereferences a NULL pointer
at position 0..0008 when setting up the crypto key in
crypto_hash_setkey() by using asoc->asoc_shared_key that is
NULL as condition key_id == asoc->active_key_id is true if
the AUTH chunk was injected correctly from remote. This
happens no matter what net.sctp.auth_enable sysctl says.
The fix is to check for net->sctp.auth_enable and for
asoc->peer.auth_capable before doing any operations like
sctp_sf_authenticate() as no key is activated in
sctp_auth_asoc_init_active_key() for each case.
Now as RFC4895 section 6.3 states that if the used HMAC-ALGO
passed from the INIT chunk was not used in the AUTH chunk, we
SHOULD send an error; however in this case it would be better
to just silently discard such a maliciously prepared handshake
as we didn't even receive a parameter at all. Also, as our
endpoint has no shared key configured, section 6.3 says that
MUST silently discard, which we are doing from now onwards.
Before calling sctp_sf_pdiscard(), we need not only to free
the association, but also the chunk->auth_chunk skb, as
commit bbd0d59809 created a skb clone in that case.
I have tested this locally by using netfilter's nfqueue and
re-injecting packets into the local stack after maliciously
modifying the INIT chunk (removing RANDOM; HMAC-ALGO param)
and the SCTP packet containing the COOKIE_ECHO (injecting
AUTH chunk before COOKIE_ECHO). Fixed with this patch applied.
Fixes: bbd0d59809 ("[SCTP]: Implement the receive and verification of AUTH chunk")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <yasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem statement: 1) both paths (primary path1 and alternate
path2) are up after the association has been established i.e.,
HB packets are normally exchanged, 2) path2 gets inactive after
path_max_retrans * max_rto timed out (i.e. path2 is down completely),
3) now, if a transmission times out on the only surviving/active
path1 (any ~1sec network service impact could cause this like
a channel bonding failover), then the retransmitted packets are
sent over the inactive path2; this happens with partial failover
and without it.
Besides not being optimal in the above scenario, a small failure
or timeout in the only existing path has the potential to cause
long delays in the retransmission (depending on RTO_MAX) until
the still active path is reselected. Further, when the T3-timeout
occurs, we have active_patch == retrans_path, and even though the
timeout occurred on the initial transmission of data, not a
retransmit, we end up updating retransmit path.
RFC4960, section 6.4. "Multi-Homed SCTP Endpoints" states under
6.4.1. "Failover from an Inactive Destination Address" the
following:
Some of the transport addresses of a multi-homed SCTP endpoint
may become inactive due to either the occurrence of certain
error conditions (see Section 8.2) or adjustments from the
SCTP user.
When there is outbound data to send and the primary path
becomes inactive (e.g., due to failures), or where the SCTP
user explicitly requests to send data to an inactive
destination transport address, before reporting an error to
its ULP, the SCTP endpoint should try to send the data to an
alternate __active__ destination transport address if one
exists.
When retransmitting data that timed out, if the endpoint is
multihomed, it should consider each source-destination address
pair in its retransmission selection policy. When retransmitting
timed-out data, the endpoint should attempt to pick the most
divergent source-destination pair from the original
source-destination pair to which the packet was transmitted.
Note: Rules for picking the most divergent source-destination
pair are an implementation decision and are not specified
within this document.
So, we should first reconsider to take the current active
retransmission transport if we cannot find an alternative
active one. If all of that fails, we can still round robin
through unkown, partial failover, and inactive ones in the
hope to find something still suitable.
Commit 4141ddc02a ("sctp: retran_path update bug fix") broke
that behaviour by selecting the next inactive transport when
no other active transport was found besides the current assoc's
peer.retran_path. Before commit 4141ddc02a, we would have
traversed through the list until we reach our peer.retran_path
again, and in case that is still in state SCTP_ACTIVE, we would
take it and return. Only if that is not the case either, we
take the next inactive transport.
Besides all that, another issue is that transports in state
SCTP_UNKNOWN could be preferred over transports in state
SCTP_ACTIVE in case a SCTP_ACTIVE transport appears after
SCTP_UNKNOWN in the transport list yielding a weaker transport
state to be used in retransmission.
This patch mostly reverts 4141ddc02a, but also rewrites
this function to introduce more clarity and strictness into
the code. A strict priority of transport states is enforced
in this patch, hence selection is active > unkown > partial
failover > inactive.
Fixes: 4141ddc02a ("sctp: retran_path update bug fix")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Acked-by: Vlad Yasevich <yasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current implementation it is possible to reach PF state from unconfirmed.
We can interpret sctp-failover-02 in a way that PF state is meant to be reached
only from active state, in the end, this is when entering PF state makes sense.
Here are few quotes from sctp-failover-02, but regardless of these, same
understanding can be reached from whole section 5:
Section 5.1, quickfailover guide:
"The PF state is an intermediate state between Active and Failed states."
"Each time the T3-rtx timer expires on an active or idle
destination, the error counter of that destination address will
be incremented. When the value in the error counter exceeds
PFMR, the endpoint should mark the destination transport address as PF."
There are several concrete reasons for such interpretation. For start, rfc4960
does not take into concern quickfailover algorithm. Therefore, quickfailover
must comply to 4960. Point where this compliance can be argued is following
behavior:
When PF is entered, association overall error counter is incremented for each
missed HB. This is contradictory to rfc4960, as address, while in unconfirmed
state, is subjected to probing, and while it is probed, it should not increment
association overall error counter. This has as a consequence that we might end
up in situation in which we drop association due path failure on unconfirmed
address, in case we have wrong configuration in a way:
Association.Max.Retrans == Path.Max.Retrans.
Another reason is that entering PF from unconfirmed will cause a loss of address
confirmed event when address is once (if) confirmed. This is fine from failover
guide point of view, but it is not consistent with behavior preceding failover
implementation and recommendation from 4960:
5.4. Path Verification
Whenever a path is confirmed, an indication MAY be given to the upper
layer.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP's sctp_connectx() abi breaks for 64bit kernels compiled with 32bit
emulation (e.g. ia32 emulation or x86_x32). Due to internal usage of
'struct sctp_getaddrs_old' which includes a struct sockaddr pointer,
sizeof(param) check will always fail in kernel as the structure in
64bit kernel space is 4bytes larger than for user binaries compiled
in 32bit mode. Thus, applications making use of sctp_connectx() won't
be able to run under such circumstances.
Introduce a compat interface in the kernel to deal with such
situations by using a 'struct compat_sctp_getaddrs_old' structure
where user data is copied into it, and then sucessively transformed
into a 'struct sctp_getaddrs_old' structure with the help of
compat_ptr(). That fixes sctp_connectx() abi without any changes
needed in user space, and lets the SCTP test suite pass when compiled
in 32bit and run on 64bit kernels.
Fixes: f9c67811eb ("sctp: Fix regression introduced by new sctp_connectx api")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementation of (a)rwnd calculation might lead to severe performance issues
and associations completely stalling. These problems are described and solution
is proposed which improves lksctp's robustness in congestion state.
1) Sudden drop of a_rwnd and incomplete window recovery afterwards
Data accounted in sctp_assoc_rwnd_decrease takes only payload size (sctp data),
but size of sk_buff, which is blamed against receiver buffer, is not accounted
in rwnd. Theoretically, this should not be the problem as actual size of buffer
is double the amount requested on the socket (SO_RECVBUF). Problem here is
that this will have bad scaling for data which is less then sizeof sk_buff.
E.g. in 4G (LTE) networks, link interfacing radio side will have a large portion
of traffic of this size (less then 100B).
An example of sudden drop and incomplete window recovery is given below. Node B
exhibits problematic behavior. Node A initiates association and B is configured
to advertise rwnd of 10000. A sends messages of size 43B (size of typical sctp
message in 4G (LTE) network). On B data is left in buffer by not reading socket
in userspace.
Lets examine when we will hit pressure state and declare rwnd to be 0 for
scenario with above stated parameters (rwnd == 10000, chunk size == 43, each
chunk is sent in separate sctp packet)
Logic is implemented in sctp_assoc_rwnd_decrease:
socket_buffer (see below) is maximum size which can be held in socket buffer
(sk_rcvbuf). current_alloced is amount of data currently allocated (rx_count)
A simple expression is given for which it will be examined after how many
packets for above stated parameters we enter pressure state:
We start by condition which has to be met in order to enter pressure state:
socket_buffer < currently_alloced;
currently_alloced is represented as size of sctp packets received so far and not
yet delivered to userspace. x is the number of chunks/packets (since there is no
bundling, and each chunk is delivered in separate packet, we can observe each
chunk also as sctp packet, and what is important here, having its own sk_buff):
socket_buffer < x*each_sctp_packet;
each_sctp_packet is sctp chunk size + sizeof(struct sk_buff). socket_buffer is
twice the amount of initially requested size of socket buffer, which is in case
of sctp, twice the a_rwnd requested:
2*rwnd < x*(payload+sizeof(struc sk_buff));
sizeof(struct sk_buff) is 190 (3.13.0-rc4+). Above is stated that rwnd is 10000
and each payload size is 43
20000 < x(43+190);
x > 20000/233;
x ~> 84;
After ~84 messages, pressure state is entered and 0 rwnd is advertised while
received 84*43B ~= 3612B sctp data. This is why external observer notices sudden
drop from 6474 to 0, as it will be now shown in example:
IP A.34340 > B.12345: sctp (1) [INIT] [init tag: 1875509148] [rwnd: 81920] [OS: 10] [MIS: 65535] [init TSN: 1096057017]
IP B.12345 > A.34340: sctp (1) [INIT ACK] [init tag: 3198966556] [rwnd: 10000] [OS: 10] [MIS: 10] [init TSN: 902132839]
IP A.34340 > B.12345: sctp (1) [COOKIE ECHO]
IP B.12345 > A.34340: sctp (1) [COOKIE ACK]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057017] [SID: 0] [SSEQ 0] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057017] [a_rwnd 9957] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057018] [SID: 0] [SSEQ 1] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057018] [a_rwnd 9957] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057019] [SID: 0] [SSEQ 2] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057019] [a_rwnd 9914] [#gap acks 0] [#dup tsns 0]
<...>
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057098] [SID: 0] [SSEQ 81] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057098] [a_rwnd 6517] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057099] [SID: 0] [SSEQ 82] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057099] [a_rwnd 6474] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057100] [SID: 0] [SSEQ 83] [PPID 0x18]
--> Sudden drop
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057100] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
At this point, rwnd_press stores current rwnd value so it can be later restored
in sctp_assoc_rwnd_increase. This however doesn't happen as condition to start
slowly increasing rwnd until rwnd_press is returned to rwnd is never met. This
condition is not met since rwnd, after it hit 0, must first reach rwnd_press by
adding amount which is read from userspace. Let us observe values in above
example. Initial a_rwnd is 10000, pressure was hit when rwnd was ~6500 and the
amount of actual sctp data currently waiting to be delivered to userspace
is ~3500. When userspace starts to read, sctp_assoc_rwnd_increase will be blamed
only for sctp data, which is ~3500. Condition is never met, and when userspace
reads all data, rwnd stays on 3569.
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057100] [a_rwnd 1505] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057100] [a_rwnd 3010] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057101] [SID: 0] [SSEQ 84] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057101] [a_rwnd 3569] [#gap acks 0] [#dup tsns 0]
--> At this point userspace read everything, rwnd recovered only to 3569
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057102] [SID: 0] [SSEQ 85] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057102] [a_rwnd 3569] [#gap acks 0] [#dup tsns 0]
Reproduction is straight forward, it is enough for sender to send packets of
size less then sizeof(struct sk_buff) and receiver keeping them in its buffers.
2) Minute size window for associations sharing the same socket buffer
In case multiple associations share the same socket, and same socket buffer
(sctp.rcvbuf_policy == 0), different scenarios exist in which congestion on one
of the associations can permanently drop rwnd of other association(s).
Situation will be typically observed as one association suddenly having rwnd
dropped to size of last packet received and never recovering beyond that point.
Different scenarios will lead to it, but all have in common that one of the
associations (let it be association from 1)) nearly depleted socket buffer, and
the other association blames socket buffer just for the amount enough to start
the pressure. This association will enter pressure state, set rwnd_press and
announce 0 rwnd.
When data is read by userspace, similar situation as in 1) will occur, rwnd will
increase just for the size read by userspace but rwnd_press will be high enough
so that association doesn't have enough credit to reach rwnd_press and restore
to previous state. This case is special case of 1), being worse as there is, in
the worst case, only one packet in buffer for which size rwnd will be increased.
Consequence is association which has very low maximum rwnd ('minute size', in
our case down to 43B - size of packet which caused pressure) and as such
unusable.
Scenario happened in the field and labs frequently after congestion state (link
breaks, different probabilities of packet drop, packet reordering) and with
scenario 1) preceding. Here is given a deterministic scenario for reproduction:
>From node A establish two associations on the same socket, with rcvbuf_policy
being set to share one common buffer (sctp.rcvbuf_policy == 0). On association 1
repeat scenario from 1), that is, bring it down to 0 and restore up. Observe
scenario 1). Use small payload size (here we use 43). Once rwnd is 'recovered',
bring it down close to 0, as in just one more packet would close it. This has as
a consequence that association number 2 is able to receive (at least) one more
packet which will bring it in pressure state. E.g. if association 2 had rwnd of
10000, packet received was 43, and we enter at this point into pressure,
rwnd_press will have 9957. Once payload is delivered to userspace, rwnd will
increase for 43, but conditions to restore rwnd to original state, just as in
1), will never be satisfied.
--> Association 1, between A.y and B.12345
IP A.55915 > B.12345: sctp (1) [INIT] [init tag: 836880897] [rwnd: 10000] [OS: 10] [MIS: 65535] [init TSN: 4032536569]
IP B.12345 > A.55915: sctp (1) [INIT ACK] [init tag: 2873310749] [rwnd: 81920] [OS: 10] [MIS: 10] [init TSN: 3799315613]
IP A.55915 > B.12345: sctp (1) [COOKIE ECHO]
IP B.12345 > A.55915: sctp (1) [COOKIE ACK]
--> Association 2, between A.z and B.12346
IP A.55915 > B.12346: sctp (1) [INIT] [init tag: 534798321] [rwnd: 10000] [OS: 10] [MIS: 65535] [init TSN: 2099285173]
IP B.12346 > A.55915: sctp (1) [INIT ACK] [init tag: 516668823] [rwnd: 81920] [OS: 10] [MIS: 10] [init TSN: 3676403240]
IP A.55915 > B.12346: sctp (1) [COOKIE ECHO]
IP B.12346 > A.55915: sctp (1) [COOKIE ACK]
--> Deplete socket buffer by sending messages of size 43B over association 1
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315613] [SID: 0] [SSEQ 0] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315613] [a_rwnd 9957] [#gap acks 0] [#dup tsns 0]
<...>
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315696] [a_rwnd 6388] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315697] [SID: 0] [SSEQ 84] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315697] [a_rwnd 6345] [#gap acks 0] [#dup tsns 0]
--> Sudden drop on 1
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315698] [SID: 0] [SSEQ 85] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315698] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
--> Here userspace read, rwnd 'recovered' to 3698, now deplete again using
association 1 so there is place in buffer for only one more packet
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315799] [SID: 0] [SSEQ 186] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315799] [a_rwnd 86] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315800] [SID: 0] [SSEQ 187] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315800] [a_rwnd 43] [#gap acks 0] [#dup tsns 0]
--> Socket buffer is almost depleted, but there is space for one more packet,
send them over association 2, size 43B
IP B.12346 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3676403240] [SID: 0] [SSEQ 0] [PPID 0x18]
IP A.55915 > B.12346: sctp (1) [SACK] [cum ack 3676403240] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
--> Immediate drop
IP A.60995 > B.12346: sctp (1) [SACK] [cum ack 387491510] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
--> Read everything from the socket, both association recover up to maximum rwnd
they are capable of reaching, note that association 1 recovered up to 3698,
and association 2 recovered only to 43
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315800] [a_rwnd 1548] [#gap acks 0] [#dup tsns 0]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315800] [a_rwnd 3053] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315801] [SID: 0] [SSEQ 188] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315801] [a_rwnd 3698] [#gap acks 0] [#dup tsns 0]
IP B.12346 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3676403241] [SID: 0] [SSEQ 1] [PPID 0x18]
IP A.55915 > B.12346: sctp (1) [SACK] [cum ack 3676403241] [a_rwnd 43] [#gap acks 0] [#dup tsns 0]
A careful reader might wonder why it is necessary to reproduce 1) prior
reproduction of 2). It is simply easier to observe when to send packet over
association 2 which will push association into the pressure state.
Proposed solution:
Both problems share the same root cause, and that is improper scaling of socket
buffer with rwnd. Solution in which sizeof(sk_buff) is taken into concern while
calculating rwnd is not possible due to fact that there is no linear
relationship between amount of data blamed in increase/decrease with IP packet
in which payload arrived. Even in case such solution would be followed,
complexity of the code would increase. Due to nature of current rwnd handling,
slow increase (in sctp_assoc_rwnd_increase) of rwnd after pressure state is
entered is rationale, but it gives false representation to the sender of current
buffer space. Furthermore, it implements additional congestion control mechanism
which is defined on implementation, and not on standard basis.
Proposed solution simplifies whole algorithm having on mind definition from rfc:
o Receiver Window (rwnd): This gives the sender an indication of the space
available in the receiver's inbound buffer.
Core of the proposed solution is given with these lines:
sctp_assoc_rwnd_update:
if ((asoc->base.sk->sk_rcvbuf - rx_count) > 0)
asoc->rwnd = (asoc->base.sk->sk_rcvbuf - rx_count) >> 1;
else
asoc->rwnd = 0;
We advertise to sender (half of) actual space we have. Half is in the braces
depending whether you would like to observe size of socket buffer as SO_RECVBUF
or twice the amount, i.e. size is the one visible from userspace, that is,
from kernelspace.
In this way sender is given with good approximation of our buffer space,
regardless of the buffer policy - we always advertise what we have. Proposed
solution fixes described problems and removes necessity for rwnd restoration
algorithm. Finally, as proposed solution is simplification, some lines of code,
along with some bytes in struct sctp_association are saved.
Version 2 of the patch addressed comments from Vlad. Name of the function is set
to be more descriptive, and two parts of code are changed, in one removing the
superfluous call to sctp_assoc_rwnd_update since call would not result in update
of rwnd, and the other being reordering of the code in a way that call to
sctp_assoc_rwnd_update updates rwnd. Version 3 corrected change introduced in v2
in a way that existing function is not reordered/copied in line, but it is
correctly called. Thanks Vlad for suggesting.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here, when the net is init_net, we needn't to kmemdup the ctl_table
again. So add a check for net. Also we can save some memory.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit 3c68198e75111a90("sctp: Make hmac algorithm selection for
cookie generation dynamic"), we miss the .data initialization.
If we don't use the net_namespace, the problem that parts of the
sysctl configuration won't be isolation and won't occur.
In sctp_sysctl_net_register(), we register the sysctl for each
net, in the for(), we use the 'table[i].data' as check condition, so
when the 'i' is the index of sctp_hmac_alg, the data is NULL, then
break. So add the .data initialization.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit efe4208f47:
'ipv6: make lookups simpler and faster' broke initialization of local source
address on accepted ipv6 sockets. Before the mentioned commit receive address
was copied along with the contents of ipv6_pinfo in sctp_v6_create_accept_sk.
Now when it is moved, it has to be copied separately.
This also fixes lksctp's ipv6 regression in a sense that test_getname_v6, TC5 -
'getsockname on a connected server socket' now passes.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined bh_[un]lock_sock to sctp_bh[un]lock_sock for user
space friendly code which we haven't use in years, so removing them.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined {lock|release}_sock to sctp_{lock|release}_sock for user space friendly
code which we haven't use in years, so removing them.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined write_[un]lock to sctp_write_[un]lock for user space
friendly code which we haven't use in years, so removing them.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined spin_[un]lock to sctp_spin_[un]lock for user space friendly
code which we haven't use in years, so removing them.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined local_bh_{disable|enable} to sctp_local_bh_{disable|enable}
for user space friendly code which we haven't use in years, so removing them.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When go the right path, the status is 0, no need to assign it again.
So just remove the assignment.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add sctp_spp_sackdelay_{enable|disable} helper function for
avoiding code duplication.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It confuses Smatch when we check "sinit" for NULL and then non-NULL and
that causes a false positive warning later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the net_random and net_srandom macros and replaces
them with direct calls to the prandom ones. As new commits only seem to
use prandom_u32 there is no use to keep them around.
This change makes it easier to grep for users of prandom_u32.
Signed-off-by: Aruna-Hewapathirane <aruna.hewapathirane@gmail.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new ip_no_pmtu_disc mode only allowes fragmentation-needed errors
to be honored by protocols which do more stringent validation on the
ICMP's packet payload. This knob is useful for people who e.g. want to
run an unmodified DNS server in a namespace where they need to use pmtu
for TCP connections (as they are used for zone transfers or fallback
for requests) but don't want to use possibly spoofed UDP pmtu information.
Currently the whitelisted protocols are TCP, SCTP and DCCP as they check
if the returned packet is in the window or if the association is valid.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently I updated the sctp socket option deprecation warnings to be both a bit
more clear and ratelimited to prevent user processes from spamming the log file.
Ben Hutchings suggested that I add the process name and pid to these warnings so
that users can tell who is responsible for using the deprecated apis. This
patch accomplishes that.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP outqueue structure maintains a data chunks
that are pending transmission, the list of chunks that
are pending a retransmission and a length of data in
flight. It also tries to keep the emtpy state so that
it can performe shutdown sequence or notify user.
The problem is that the empy state is inconsistently
tracked. It is possible to completely drain the queue
without sending anything when using PR-SCTP. In this
case, the empty state will not be correctly state as
report by Jamal Hadi Salim <jhs@mojatatu.com>. This
can cause an association to be perminantly stuck in the
SHUTDOWN_PENDING state.
Additionally, SCTP is incredibly inefficient when setting
the empty state. Even though all the data is availaible
in the outqueue structure, we ignore it and walk a list
of trasnports.
In the end, we can completely remove the extra empty
state and figure out if the queue is empty by looking
at 3 things: length of pending data, length of in-flight
data, and exisiting of retransmit data. All of these
are already in the strucutre.
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dst_set will use dst, if dst is NULL although is not a problem,
then goto the 'no_route' and free nskb, so do the skb_dst_set is pointless.
so move the skb_dst_set after dst check.
Remove the unnecessary initialization as well.
v2: fix the subject line because it would confuse people,
as pointed out by Daniel.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a recent discussion regarding some sctp socket options, it was noted that
we have several points at which we issue log warnings that can be flooded at an
unbounded rate by any user. Fix this by converting all the pr_warns in the
sctp_setsockopt path to be pr_warn_ratelimited.
Note there are several debug level messages as well. I'm leaving those alone,
as, if you turn on pr_debug, you likely want lots of verbosity.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors below:
ERROR: that open brace { should be on the previous line
ERROR: open brace '{' following function declarations go on the next line
ERROR: trailing statements should be on next line
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors below:
ERROR: switch and case should be at the same inden
ERROR: code indent should use tabs where possible
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors below:
ERROR: "(foo*)" should be "(foo *)"
ERROR: "foo * bar" should be "foo *bar"
ERROR: "foo* bar" should be "foo *bar"
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors while the space is required or prohibited
to the "=,()++..."
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switch() had do return, and never use the 'return NULL'. The
'break' after return or goto has no effect. Remove it.
v2: make it more readable as suggested by Neil.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove the unnecessary cast.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 93b36cf342 ("ipv6: support IPV6_PMTU_INTERFACE on sockets")
I made a horrible mistake to add ip6_sk_accept_pmtu to the generic
sctp_icmp_frag_needed path. This results in build warnings if IPv6 is
disabled which were luckily caught by Fengguang's kbuild bot. But it
also leads to a kernel panic IPv4 frag-needed packet is received.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile error reported by Jim Davis on netdev.
ip6_sk_accept_pmtu() needs net/ip6_route.h
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2013-12-19
1) Use the user supplied policy index instead of a generated one
if present. From Fan Du.
2) Make xfrm migration namespace aware. From Fan Du.
3) Make the xfrm state and policy locks namespace aware. From Fan Du.
4) Remove ancient sleeping when the SA is in acquire state,
we now queue packets to the policy instead. This replaces the
sleeping code.
5) Remove FLOWI_FLAG_CAN_SLEEP. This was used to notify xfrm about the
posibility to sleep. The sleeping code is gone, so remove it.
6) Check user specified spi for IPComp. Thr spi for IPcomp is only
16 bit wide, so check for a valid value. From Fan Du.
7) Export verify_userspi_info to check for valid user supplied spi ranges
with pfkey and netlink. From Fan Du.
8) RFC3173 states that if the total size of a compressed payload and the IPComp
header is not smaller than the size of the original payload, the IP datagram
must be sent in the original non-compressed form. These packets are dropped
by the inbound policy check because they are not transformed. Document the need
to set 'level use' for IPcomp to receive such packets anyway. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IPV6_PMTU_INTERFACE is the same as IPV6_PMTU_PROBE for ipv6. Add it
nontheless for symmetry with IPv4 sockets. Also drop incoming MTU
information if this mode is enabled.
The additional bit in ipv6_pinfo just eats in the padding behind the
bitfield. There are no changes to the layout of the struct at all.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
when I modprobe sctp_probe, it failed with "FATAL: ". I found that
sctp should load before sctp_probe register jprobe. So I add a
sctp_setup_jprobe for loading 'sctp' when first failed to register
jprobe, just do this similar to dccp_probe.
v2: add MODULE_SOFTDEP and check of request_module, as suggested by Neil
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sctp_err_lookup, goto out while the asoc is not NULL, so remove the
check NULL. Also, in sctp_err_finish which called by sctp_v4_err and
sctp_v6_err, they pass asoc to sctp_err_finish while the asoc is not
NULL, so remove the check.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix up spacing of proc_sctp_do_hmac_alg for according to the
proc_sctp_do_rto_min[max] in sysctl.c
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rto_min should be smaller than rto_max while rto_max should be larger
than rto_min. Add two proc_handler for the checking.
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we set 0 to rto_min or rto_max, just not change the value. Also
we should check the rto_min > rto_max.
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, sctp associations latch a sockets autoclose value to an association
at association init time, subject to capping constraints from the max_autoclose
sysctl value. This leads to an odd situation where an application may set a
socket level autoclose timeout, but sliently sctp will limit the autoclose
timeout to something less than that.
Fix this by modifying the autoclose setsockopt function to check the limit, cap
it and warn the user via syslog that the timeout is capped. This will allow
getsockopt to return valid autoclose timeout values that reflect what subsequent
associations actually use.
While were at it, also elimintate the assoc->autoclose variable, it duplicates
whats in the timeout array, which leads to multiple sources for the same
information, that may differ (as the former isn't subject to any capping). This
gives us the timeout information in a canonical place and saves some space in
the association structure as well.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
CC: Wang Weidong <wangweidong1@huawei.com>
CC: David Miller <davem@davemloft.net>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
fix some typos
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_peer_needs_update only return 0 or 1.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more simplification.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kzalloc had initialize the allocated memroy. Therefore, remove the
initialize with 0 and the memset.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FLOWI_FLAG_CAN_SLEEP was used to notify xfrm about the posibility
to sleep until the needed states are resolved. This code is gone,
so FLOWI_FLAG_CAN_SLEEP is not needed anymore.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
As Michael pointed out that when max_burst is 0, it just disable
max_burst. It declared in rfc6458#section-8.1.24. so add the check
in sctp_transport_burst_limited, when it 0, just do nothing.
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <Michael.Tuexen@lurchi.franken.de>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently retransmitted DATA chunks could also be used for
RTT measurements since there are no flag to identify whether
the transmitted DATA chunk is a new one or a retransmitted one.
This problem is introduced by commit ae19c5486 ("sctp: remove
'resent' bit from the chunk") which inappropriately removed the
'resent' bit completely, instead of doing this, we should set
the resent bit only for the retransmitted DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function sctp_check_transmitted(transport t, ...) would iterate all of
transport->transmitted queue and looking for the highest __newly__ acked tsn.
The original algorithm would depend on the order of the assoc->transport_list
(in function sctp_outq_sack line 1215 - 1226). The result might not be the
expected due to the order of the tranport_list.
Solution: checking if the exising is smaller than the new one before assigning
Signed-off-by: Chang Xiangzhong <changxiangzhong@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
All seq_printf() users are using "%n" for calculating padding size,
convert them to use seq_setwidth() / seq_pad() pair.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Joe Perches <joe@perches.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a transport recovers due to the new coming sack, SCTP should
iterate all of its transport_list to locate the __two__ most recently used
transport and set to active_path and retran_path respectively. The exising
code does not find the two properly - In case of the following list:
[most-recent] -> [2nd-most-recent] -> ...
Both active_path and retran_path would be set to the 1st element.
The bug happens when:
1) multi-homing
2) failure/partial_failure transport recovers
Both active_path and retran_path would be set to the same most-recent one, in
other words, retran_path would not take its role - an end user might not even
notice this issue.
Signed-off-by: Chang Xiangzhong <changxiangzhong@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in f9e42b8535 ("net: sctp: sideeffect: throw BUG if
primary_path is NULL"), we intended to find a buggy assoc that's
part of the assoc hash table with a primary_path that is NULL.
However, we better remove the BUG_ON for now and find a more
suitable place to assert for these things as Mark reports that
this also triggers the bug when duplication cookie processing
happens, and the assoc is not part of the hash table (so all
good in this case). Such a situation can for example easily be
reproduced by:
tc qdisc add dev eth0 root handle 1: prio bands 2 priomap 1 1 1 1 1 1
tc qdisc add dev eth0 parent 1:2 handle 20: netem loss 20%
tc filter add dev eth0 protocol ip parent 1: prio 2 u32 match ip \
protocol 132 0xff match u8 0x0b 0xff at 32 flowid 1:2
This drops 20% of COOKIE-ACK packets. After some follow-up
discussion with Vlad we came to the conclusion that for now we
should still better remove this BUG_ON() assertion, and come up
with two follow-ups later on, that is, i) find a more suitable
place for this assertion, and possibly ii) have a special
allocator/initializer for such kind of temporary assocs.
Reported-by: Mark Thomas <Mark.Thomas@metaswitch.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an outstanding bug found through IPVS, where SCTP packets
with skb->data_len > 0 (non-linearized) and empty frag_list, but data
accumulated in frags[] member, are forwarded with incorrect checksum
letting SCTP initial handshake fail on some systems. Linearizing each
SCTP skb in IPVS to prevent that would not be a good solution as
this leads to an additional and unnecessary performance penalty on
the load-balancer itself for no good reason (as we actually only want
to update the checksum, and can do that in a different/better way
presented here).
The actual problem is elsewhere, namely, that SCTP's checksumming
in sctp_compute_cksum() does not take frags[] into account like
skb_checksum() does. So while we are fixing this up, we better reuse
the existing code that we have anyway in __skb_checksum() and use it
for walking through the data doing checksumming. This will not only
fix this issue, but also consolidates some SCTP code with core
sk_buff code, bringing it closer together and removing respectively
avoiding reimplementation of skb_checksum() for no good reason.
As crc32c() can use hardware implementation within the crypto layer,
we leave that intact (it wraps around / falls back to e.g. slice-by-8
algorithm in __crc32c_le() otherwise); plus use the __crc32c_le_combine()
combinator for crc32c blocks.
Also, we remove all other SCTP checksumming code, so that we only
have to use sctp_compute_cksum() from now on; for doing that, we need
to transform SCTP checkumming in output path slightly, and can leave
the rest intact.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two if statements do the same work, we can merge them to
one. And fix some typos. There is just code simplification,
no functional changes.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmem_cache_zalloc had set the allocated memory to zero. I think no need
to initialize with 0. And move the comments to the function begin.
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix some typos
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8a07eb0a50 ("sctp: Add ASCONF operation on the single-homed host")
implemented possible use of IPv4 addresses with non SCTP_ADDR_SRC state
as source address when sending ASCONF (ADD) packets, but IPv6 part for
that was not implemented in 8a07eb0a50. Therefore, as this is not restricted
to IPv4-only, fix this up to allow the same for IPv6 addresses in SCTP.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Michio Honda <micchie@sfc.wide.ad.jp>
Acked-by: Michio Honda <micchie@sfc.wide.ad.jp>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
IP/IPv6 fragmentation knows how to compute only TCP/UDP checksum.
This causes problems if SCTP packets has to be fragmented and
ipsummed has been set to PARTIAL due to checksum offload support.
This condition can happen when retransmitting after MTU discover,
or when INIT or other control chunks are larger then MTU.
Check for the rare fragmentation condition in SCTP and use software
checksum calculation in this case.
CC: Fan Du <fan.du@windriver.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb/ixgbe have hardware sctp checksum support, when this feature is enabled
and also IPsec is armed to protect sctp traffic, ugly things happened as
xfrm_output checks CHECKSUM_PARTIAL to do checksum operation(sum every thing
up and pack the 16bits result in the checksum field). The result is fail
establishment of sctp communication.
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP listener refactoring, part 4 :
To speed up inet lookups, we moved IPv4 addresses from inet to struct
sock_common
Now is time to do the same for IPv6, because it permits us to have fast
lookups for all kind of sockets, including upcoming SYN_RECV.
Getting IPv6 addresses in TCP lookups currently requires two extra cache
lines, plus a dereference (and memory stall).
inet6_sk(sk) does the dereference of inet_sk(__sk)->pinet6
This patch is way bigger than its IPv4 counter part, because for IPv4,
we could add aliases (inet_daddr, inet_rcv_saddr), while on IPv6,
it's not doable easily.
inet6_sk(sk)->daddr becomes sk->sk_v6_daddr
inet6_sk(sk)->rcv_saddr becomes sk->sk_v6_rcv_saddr
And timewait socket also have tw->tw_v6_daddr & tw->tw_v6_rcv_saddr
at the same offset.
We get rid of INET6_TW_MATCH() as INET6_MATCH() is now the generic
macro.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Move sysctl_local_ports from a global variable into struct netns_ipv4.
- Modify inet_get_local_port_range to take a struct net, and update all
of the callers.
- Move the initialization of sysctl_local_ports into
sysctl_net_ipv4.c:ipv4_sysctl_init_net from inet_connection_sock.c
v2:
- Ensure indentation used tabs
- Fixed ip.h so it applies cleanly to todays net-next
v3:
- Compile fixes of strange callers of inet_get_local_port_range.
This patch now successfully passes an allmodconfig build.
Removed manual inlining of inet_get_local_port_range in ipv4_local_port_range
Originally-by: Samya <samya@twitter.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the same behaviour for SCTP as present in TCP for ICMP redirect
messages. For IPv6, RFC4443, section 2.4. says:
...
(e) An ICMPv6 error message MUST NOT be originated as a result of
receiving the following:
...
(e.2) An ICMPv6 redirect message [IPv6-DISC].
...
Therefore, do not report an error to user space, just invoke dst's redirect
callback and leave, same for IPv4 as done in TCP as well. The implication
w/o having this patch could be that the reception of such packets would
generate a poll notification and in worst case it could even tear down the
whole connection. Therefore, stop updating sk_err on redirects.
Reported-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Chester reported an issue with IPv6 on SCTP that IPsec traffic is not
being encrypted, whereas on IPv4 it is. Setting up an AH + ESP transport
does not seem to have the desired effect:
SCTP + IPv4:
22:14:20.809645 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 116)
192.168.0.2 > 192.168.0.5: AH(spi=0x00000042,sumlen=16,seq=0x1): ESP(spi=0x00000044,seq=0x1), length 72
22:14:20.813270 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 340)
192.168.0.5 > 192.168.0.2: AH(spi=0x00000043,sumlen=16,seq=0x1):
SCTP + IPv6:
22:31:19.215029 IP6 (class 0x02, hlim 64, next-header SCTP (132) payload length: 364)
fe80::222:15ff:fe87:7fc.3333 > fe80::92e6:baff:fe0d:5a54.36767: sctp
1) [INIT ACK] [init tag: 747759530] [rwnd: 62464] [OS: 10] [MIS: 10]
Moreover, Alan says:
This problem was seen with both Racoon and Racoon2. Other people have seen
this with OpenSwan. When IPsec is configured to encrypt all upper layer
protocols the SCTP connection does not initialize. After using Wireshark to
follow packets, this is because the SCTP packet leaves Box A unencrypted and
Box B believes all upper layer protocols are to be encrypted so it drops
this packet, causing the SCTP connection to fail to initialize. When IPsec
is configured to encrypt just SCTP, the SCTP packets are observed unencrypted.
In fact, using `socat sctp6-listen:3333 -` on one end and transferring "plaintext"
string on the other end, results in cleartext on the wire where SCTP eventually
does not report any errors, thus in the latter case that Alan reports, the
non-paranoid user might think he's communicating over an encrypted transport on
SCTP although he's not (tcpdump ... -X):
...
0x0030: 5d70 8e1a 0003 001a 177d eb6c 0000 0000 ]p.......}.l....
0x0040: 0000 0000 706c 6169 6e74 6578 740a 0000 ....plaintext...
Only in /proc/net/xfrm_stat we can see XfrmInTmplMismatch increasing on the
receiver side. Initial follow-up analysis from Alan's bug report was done by
Alexey Dobriyan. Also thanks to Vlad Yasevich for feedback on this.
SCTP has its own implementation of sctp_v6_xmit() not calling inet6_csk_xmit().
This has the implication that it probably never really got updated along with
changes in inet6_csk_xmit() and therefore does not seem to invoke xfrm handlers.
SCTP's IPv4 xmit however, properly calls ip_queue_xmit() to do the work. Since
a call to inet6_csk_xmit() would solve this problem, but result in unecessary
route lookups, let us just use the cached flowi6 instead that we got through
sctp_v6_get_dst(). Since all SCTP packets are being sent through sctp_packet_transmit(),
we do the route lookup / flow caching in sctp_transport_route(), hold it in
tp->dst and skb_dst_set() right after that. If we would alter fl6->daddr in
sctp_v6_xmit() to np->opt->srcrt, we possibly could run into the same effect
of not having xfrm layer pick it up, hence, use fl6_update_dst() in sctp_v6_get_dst()
instead to get the correct source routed dst entry, which we assign to the skb.
Also source address routing example from 625034113 ("sctp: fix sctp to work with
ipv6 source address routing") still works with this patch! Nevertheless, in RFC5095
it is actually 'recommended' to not use that anyway due to traffic amplification [1].
So it seems we're not supposed to do that anyway in sctp_v6_xmit(). Moreover, if
we overwrite the flow destination here, the lower IPv6 layer will be unable to
put the correct destination address into IP header, as routing header is added in
ipv6_push_nfrag_opts() but then probably with wrong final destination. Things aside,
result of this patch is that we do not have any XfrmInTmplMismatch increase plus on
the wire with this patch it now looks like:
SCTP + IPv6:
08:17:47.074080 IP6 2620:52:0:102f:7a2b:cbff:fe27:1b0a > 2620:52:0:102f:213:72ff:fe32:7eba:
AH(spi=0x00005fb4,seq=0x1): ESP(spi=0x00005fb5,seq=0x1), length 72
08:17:47.074264 IP6 2620:52:0:102f:213:72ff:fe32:7eba > 2620:52:0:102f:7a2b:cbff:fe27:1b0a:
AH(spi=0x00003d54,seq=0x1): ESP(spi=0x00003d55,seq=0x1), length 296
This fixes Kernel Bugzilla 24412. This security issue seems to be present since
2.6.18 kernels. Lets just hope some big passive adversary in the wild didn't have
its fun with that. lksctp-tools IPv6 regression test suite passes as well with
this patch.
[1] http://www.secdev.org/conf/IPv6_RH_security-csw07.pdf
Reported-by: Alan Chester <alan.chester@tekelec.com>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was originally reported in [1] and posted by Neil Horman [2], he said:
Fix up a missed null pointer check in the asconf code. If we don't find
a local address, but we pass in an address length of more than 1, we may
dereference a NULL laddr pointer. Currently this can't happen, as the only
users of the function pass in the value 1 as the addrcnt parameter, but
its not hot path, and it doesn't hurt to check for NULL should that ever
be the case.
The callpath from sctp_asconf_mgmt() looks okay. But this could be triggered
from sctp_setsockopt_bindx() call with SCTP_BINDX_REM_ADDR and addrcnt > 1
while passing all possible addresses from the bind list to SCTP_BINDX_REM_ADDR
so that we do *not* find a single address in the association's bind address
list that is not in the packed array of addresses. If this happens when we
have an established association with ASCONF-capable peers, then we could get
a NULL pointer dereference as we only check for laddr == NULL && addrcnt == 1
and call later sctp_make_asconf_update_ip() with NULL laddr.
BUT: this actually won't happen as sctp_bindx_rem() will catch such a case
and return with an error earlier. As this is incredably unintuitive and error
prone, add a check to catch at least future bugs here. As Neil says, its not
hot path. Introduced by 8a07eb0a5 ("sctp: Add ASCONF operation on the
single-homed host").
[1] http://www.spinics.net/lists/linux-sctp/msg02132.html
[2] http://www.spinics.net/lists/linux-sctp/msg02133.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Michio Honda <micchie@sfc.wide.ad.jp>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we do not add braces around ...
mask |= POLLERR |
sock_flag(sk, SOCK_SELECT_ERR_QUEUE) ? POLLPRI : 0;
... then this condition always evaluates to true as POLLERR is
defined as 8 and binary or'd with whatever result comes out of
sock_flag(). Hence instead of (X | Y) ? A : B, transform it into
X | (Y ? A : B). Unfortunatelty, commit 8facd5fb73 ("net: fix
smatch warnings inside datagram_poll") forgot about SCTP. :-(
Introduced by 7d4c04fc17 ("net: add option to enable error queue
packets waking select").
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: sctp: Fix data chunk fragmentation for MTU values which are not multiple of 4
Initially the problem was observed with ipsec, but later it became clear that
SCTP data chunk fragmentation algorithm has problems with MTU values which are
not multiple of 4. Test program was used which just transmits 2000 bytes long
packets to other host. tcpdump was used to observe re-fragmentation in IP layer
after SCTP already fragmented data chunks.
With MTU 1500:
12:54:34.082904 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 1500)
10.151.38.153.39303 > 10.151.24.91.54321: sctp (1) [DATA] (B) [TSN: 2366088589] [SID: 0] [SSEQ 1] [PPID 0x0]
12:54:34.082933 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 596)
10.151.38.153.39303 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 2366088590] [SID: 0] [SSEQ 1] [PPID 0x0]
12:54:34.090576 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.39303: sctp (1) [SACK] [cum ack 2366088590] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
With MTU 1499:
13:02:49.955220 IP (tos 0x2,ECT(0), ttl 64, id 48215, offset 0, flags [+], proto SCTP (132), length 1492)
10.151.38.153.39084 > 10.151.24.91.54321: sctp[|sctp]
13:02:49.955249 IP (tos 0x2,ECT(0), ttl 64, id 48215, offset 1472, flags [none], proto SCTP (132), length 28)
10.151.38.153 > 10.151.24.91: ip-proto-132
13:02:49.955262 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 600)
10.151.38.153.39084 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 404355346] [SID: 0] [SSEQ 1] [PPID 0x0]
13:02:49.956770 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.39084: sctp (1) [SACK] [cum ack 404355346] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
Here problem in data portion limit calculation leads to re-fragmentation in IP,
which is sub-optimal. The problem is max_data initial value, which doesn't take
into account the fact, that data chunk must be padded to 4-bytes boundary.
It's enough to correct max_data, because all later adjustments are correctly
aligned to 4-bytes boundary.
After the fix is applied, everything is fragmented correctly for uneven MTUs:
15:16:27.083881 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 1496)
10.151.38.153.53417 > 10.151.24.91.54321: sctp (1) [DATA] (B) [TSN: 3077098183] [SID: 0] [SSEQ 1] [PPID 0x0]
15:16:27.083907 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto SCTP (132), length 600)
10.151.38.153.53417 > 10.151.24.91.54321: sctp (1) [DATA] (E) [TSN: 3077098184] [SID: 0] [SSEQ 1] [PPID 0x0]
15:16:27.085640 IP (tos 0x2,ECT(0), ttl 63, id 0, offset 0, flags [DF], proto SCTP (132), length 48)
10.151.24.91.54321 > 10.151.38.153.53417: sctp (1) [SACK] [cum ack 3077098184] [a_rwnd 79920] [#gap acks 0] [#dup tsns 0]
The bug was there for years already, but
- is a performance issue, the packets are still transmitted
- doesn't show up with default MTU 1500, but possibly with ipsec (MTU 1438)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up commit for commit b1dcdc68b1 ("net: tcp_probe:
allow more advanced ingress filtering by mark") that allows for
advanced SCTP probe module filtering based on skb mark (for a more
detailed description and advantages using mark, refer to b1dcdc68b1).
The current option to filter by a given port is still being preserved.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a comment related to RFC4960 explaning why we do not check for initial
TSN, and while at it, remove yoda notation checks and clean up code from
checks of mandatory conditions. That's probably just really minor, but makes
reviewing easier.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can simply use the %pISc format specifier that was recently added
and thus remove some code that distinguishes between IPv4 and IPv6.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UIDs are printed in the proc_fs as signed int, whereas
they are unsigned int.
Signed-off-by: Francesco Fusco <ffusco@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably this one is quite unlikely to be triggered, but it's more safe
to do the call_rcu() at the end after we have dropped the reference on
the asoc and freed sctp packet chunks. The reason why is because in
sctp_transport_destroy_rcu() the transport is being kfree()'d, and if
we're unlucky enough we could run into corrupted pointers. Probably
that's more of theoretical nature, but it's safer to have this simple fix.
Introduced by commit 8c98653f ("sctp: sctp_close: fix release of bindings
for deferred call_rcu's"). I also did the 8c98653f regression test and
it's fine that way.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP Quick failover draft [1] section 5.1, point 5 says that the cwnd
should be 1 MTU. So, instead of 1, set it to 1 MTU.
[1] https://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
Reported-by: Karl Heiss <kheiss@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sctp sits on IPv6, sctp_transport_dst_check pass cookie as ZERO,
as a result ip6_dst_check always fail out. This behaviour makes
transport->dst useless, because every sctp_packet_transmit must look
for valid dst.
Add a dst_cookie into sctp_transport, and set the cookie whenever we
get new dst for sctp_transport. So dst validness could be checked
against it.
Since I have split genid for IPv4 and IPv6, also delete/add IPv6 address
will also bump IPv6 genid. So issues we discussed in:
http://marc.info/?l=linux-netdev&m=137404469219410&w=4
have all been sloved for this patch.
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the SCTP checksum calculation code from various
places to a single new function, sctp_compute_cksum(skb, offset).
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP mailing list address to send patches or questions
to is linux-sctp@vger.kernel.org and not
lksctp-developers@lists.sourceforge.net anymore. Therefore,
update all occurences.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix has been proposed originally by Vlad Yasevich. He says:
When SCTP makes forward progress (receives a SACK that acks new chunks,
renegs, or answeres 0-window probes) or when HB-ACK arrives, mark
the route as confirmed so we don't unnecessarily send NUD probes.
Having a simple SCTP client/server that exchange data chunks every 1sec,
without this patch ARP requests are sent periodically every 40-60sec.
With this fix applied, an ARP request is only done once right at the
"session" beginning. Also, when clearing the related ARP cache entry
manually during the session, a new request is correctly done. I have
only "backported" this to net-next and tested that it works, so full
credit goes to Vlad.
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro get_unused_fd() is used to allocate a file descriptor with
default flags. Those default flags (0) can be "unsafe":
O_CLOEXEC must be used by default to not leak file descriptor
across exec().
Instead of macro get_unused_fd(), functions anon_inode_getfd()
or get_unused_fd_flags() should be used with flags given by userspace.
If not possible, flags should be set to O_CLOEXEC to provide userspace
with a default safe behavor.
In a further patch, get_unused_fd() will be removed so that
new code start using anon_inode_getfd() or get_unused_fd_flags()
with correct flags.
This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.
The hard coded flag value (0) should be reviewed on a per-subsystem basis,
and, if possible, set to O_CLOEXEC.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After having reworked the debugging framework, Neil and Vlad agreed to
get rid of the leftover SCTP_DBG_TSNS code for a couple of reasons:
We can use systemtap scripts to investigate these things, we now have
pr_debug() helpers that make life easier, and if we really need anything
else besides those tools, we will be forced to come up with something
better than we have there. Therefore, get rid of this ifdef debugging
code entirely for now.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get rid of all own SCTP debug printk macros and use the ones
that the kernel offers anyway instead. This makes the code more readable
and conform to the kernel code, and offers all the features of dynamic
debbuging that pr_debug() et al has, such as only turning on/off portions
of debug messages at runtime through debugfs. The runtime cost of having
CONFIG_DYNAMIC_DEBUG enabled, but none of the debug statements printing,
is negligible [1]. If kernel debugging is completly turned off, then these
statements will also compile into "empty" functions.
While we're at it, we also need to change the Kconfig option as it /now/
only refers to the ifdef'ed code portions in outqueue.c that enable further
debugging/tracing of SCTP transaction fields. Also, since SCTP_ASSERT code
was enabled with this Kconfig option and has now been removed, we
transform those code parts into WARNs resp. where appropriate BUG_ONs so
that those bugs can be more easily detected as probably not many people
have SCTP debugging permanently turned on.
To turn on all SCTP debugging, the following steps are needed:
# mount -t debugfs none /sys/kernel/debug
# echo -n 'module sctp +p' > /sys/kernel/debug/dynamic_debug/control
This can be done more fine-grained on a per file, per line basis and others
as described in [2].
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-39-46.pdf
[2] Documentation/dynamic-debug-howto.txt
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have an extra ret variable when we directly can return
the value of sctp_get_port_local().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather instead of having the endpoint clean the garbage from the
socket, use a sk_destruct handler sctp_destruct_sock(), that does
the job for that when there are no more references on the socket.
At least do this for our crypto transform through crypto_free_hash()
that is allocated when in listening state.
Also, perform sctp_put_port() only when sk is valid. At a later
point in time we can still determine if there's an option of
placing this into sk_prot->unhash() or sctp_endpoint_free() without
any races. For now, leave it in sctp_endpoint_destroy() though.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A trailing newline has been forgotten to add into the WARN().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SCTP code defines its own timeval functions (since timeval
is rarely used inside the kernel by others), namely tv_lt() and
TIMEVAL_ADD() macros, that operate on SCTP cookie expiration.
We might as well remove all those, and operate directly on ktime
structures for a couple of reasons: ktime is available on all archs;
complexity of ktime calculations depending on the arch is less than
(reduces to a simple arithmetic operations on archs with
BITS_PER_LONG == 64 or CONFIG_KTIME_SCALAR) or equal to timeval
functions (other archs); code becomes more readable; macros can be
thrown out.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP_STATIC is just another define for the static keyword. It's use
is inconsistent in the SCTP code anyway and it was introduced in the
initial implementation of SCTP in 2.5. We have a regression suite in
lksctp-tools, but this is for user space only, so noone makes use of
this macro anymore. The kernel test suite for 2.5 is incompatible with
the current SCTP code anyway.
So simply Remove it, to be more consistent with the rest of the kernel
code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t_new rather obfuscates things where everyone else is using actual
function names instead of that macro, so replace it with kzalloc,
which is the function t_new wraps.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
