Intel SDM 17.2.4 (Debug Control Register (DR7)) says: "The processor clears the
GD flag upon entering to the debug exception handler." This sentence may be
misunderstood as if it happens only on #DB due to debug-register protection,
but it happens regardless to the cause of the #DB.
Fix the behavior to match both real hardware and Bochs.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous patch blocked invalid writes directly when the MSR
is written. As a precaution, prevent future similar mistakes by
gracefulling handle GPs caused by writes to shared MSRs.
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Honig <ahonig@google.com>
[Remove parts obsoleted by Nadav's patch. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Upon WRMSR, the CPU should inject #GP if a non-canonical value (address) is
written to certain MSRs. The behavior is "almost" identical for AMD and Intel
(ignoring MSRs that are not implemented in either architecture since they would
anyhow #GP). However, IA32_SYSENTER_ESP and IA32_SYSENTER_EIP cause #GP if
non-canonical address is written on Intel but not on AMD (which ignores the top
32-bits).
Accordingly, this patch injects a #GP on the MSRs which behave identically on
Intel and AMD. To eliminate the differences between the architecutres, the
value which is written to IA32_SYSENTER_ESP and IA32_SYSENTER_EIP is turned to
canonical value before writing instead of injecting a #GP.
Some references from Intel and AMD manuals:
According to Intel SDM description of WRMSR instruction #GP is expected on
WRMSR "If the source register contains a non-canonical address and ECX
specifies one of the following MSRs: IA32_DS_AREA, IA32_FS_BASE, IA32_GS_BASE,
IA32_KERNEL_GS_BASE, IA32_LSTAR, IA32_SYSENTER_EIP, IA32_SYSENTER_ESP."
According to AMD manual instruction manual:
LSTAR/CSTAR (SYSCALL): "The WRMSR instruction loads the target RIP into the
LSTAR and CSTAR registers. If an RIP written by WRMSR is not in canonical
form, a general-protection exception (#GP) occurs."
IA32_GS_BASE and IA32_FS_BASE (WRFSBASE/WRGSBASE): "The address written to the
base field must be in canonical form or a #GP fault will occur."
IA32_KERNEL_GS_BASE (SWAPGS): "The address stored in the KernelGSbase MSR must
be in canonical form."
This patch fixes CVE-2014-3610.
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
In order to make the APIC access page migratable, stop pinning it in
memory.
And because the APIC access page is not pinned in memory, we can
remove kvm_arch->apic_access_page. When we need to write its
physical address into vmcs, we use gfn_to_page() to get its page
struct, which is needed to call page_to_phys(); the page is then
immediately unpinned.
Suggested-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the APIC access page is pinned by KVM for the entire life
of the guest. We want to make it migratable in order to make memory
hot-unplug available for machines that run KVM.
This patch prepares to handle this in generic code, through a new
request bit (that will be set by the MMU notifier) and a new hook
that is called whenever the request bit is processed.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be used to let the guest run while the APIC access page is
not pinned. Because subsequent patches will fill in the function
for x86, place the (still empty) x86 implementation in the x86.c file
instead of adding an inline function in kvm_host.h.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid open coded calculations for bank MSRs by using well-defined
macros that hide the index of higher bank MSRs.
No semantic changes.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guest which sets the PAT CR to invalid value should get a #GP. Currently, if
vmx supports loading PAT CR during entry, then the value is not checked. This
patch makes the required check in that case.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A one-line wrapper around kvm_make_request is not particularly
useful. Replace kvm_mmu_flush_tlb() with kvm_make_request().
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- we count KVM_REQ_TLB_FLUSH requests, not actual flushes
(KVM can have multiple requests for one flush)
- flushes from kvm_flush_remote_tlbs aren't counted
- it's easy to make a direct request by mistake
Solve these by postponing the counting to kvm_check_request().
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit fc3a9157d3 ("KVM: X86: Don't report L2 emulation failures to
user-space") disabled the reporting of L2 (nested guest) emulation failures to
userspace due to race-condition between a vmexit and the instruction emulator.
The same rational applies also to userspace applications that are permitted by
the guest OS to access MMIO area or perform PIO.
This patch extends the current behavior - of injecting a #UD instead of
reporting it to userspace - also for guest userspace code.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_arch->ept_identity_pagetable holds the ept identity pagetable page. But
it is never used to refer to the page at all.
In vcpu initialization, it indicates two things:
1. indicates if ept page is allocated
2. indicates if a memory slot for identity page is initialized
Actually, kvm_arch->ept_identity_pagetable_done is enough to tell if the ept
identity pagetable is initialized. So we can remove ept_identity_pagetable.
NOTE: In the original code, ept identity pagetable page is pinned in memroy.
As a result, it cannot be migrated/hot-removed. After this patch, since
kvm_arch->ept_identity_pagetable is removed, ept identity pagetable page
is no longer pinned in memory. And it can be migrated/hot-removed.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch replace the set_bit method by kvm_make_request
to make code more readable and consistent.
Signed-off-by: Guo Hui Liu <liuguohui@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, if a permission error happens during the translation of
the final GPA to HPA, walk_addr_generic returns 0 but does not fill
in walker->fault. To avoid this, add an x86_exception* argument
to the translate_gpa function, and let it fill in walker->fault.
The nested_page_fault field will be true, since the walk_mmu is the
nested_mmu and translate_gpu instead operates on the "outer" (NPT)
instance.
Reported-by: Valentine Sinitsyn <valentine.sinitsyn@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a nested page fault happens during emulation, we will inject a vmexit,
not a page fault. However because writeback happens after the injection,
we will write ctxt->eip from L2 into the L1 EIP. We do not write back
if an instruction caused an interception vmexit---do the same for page
faults.
Suggested-by: Gleb Natapov <gleb@kernel.org>
Reviewed-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The check introduced in commit d7a2a246a1 (KVM: x86: #GP when attempts to write reserved bits of Variable Range MTRRs, 2014-08-19)
will break if the guest maxphyaddr is higher than the host's (which
sometimes happens depending on your hardware and how QEMU is
configured).
To fix this, use cpuid_maxphyaddr similar to how the APIC_BASE MSR
does already.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the beggining was on_each_cpu(), which required an unused argument to
kvm_arch_ops.hardware_{en,dis}able, but this was soon forgotten.
Remove unnecessary arguments that stem from this.
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tracepoint for dynamic PLE window, fired on every potential change.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
sched_in preempt notifier is available for x86, allow its use in
specific virtualization technlogies as well.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce preempt notifiers for architecture specific code.
Advantage over creating a new notifier in every arch is slightly simpler
code and guaranteed call order with respect to kvm_sched_in.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These were reported when running Jailhouse on AMD processors.
Initialize ctxt->exception.vector with an invalid exception number,
and warn if it remained invalid even though the emulator got
an X86EMUL_PROPAGATE_FAULT return code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Section 11.11.2.3 of the SDM mentions "All other bits in the IA32_MTRR_PHYSBASEn
and IA32_MTRR_PHYSMASKn registers are reserved; the processor generates a
general-protection exception(#GP) if software attempts to write to them". This
patch do it in kvm.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The first entry in each pair(IA32_MTRR_PHYSBASEn) defines the base
address and memory type for the range; the second entry(IA32_MTRR_PHYSMASKn)
contains a mask used to determine the address range. The legal values
for the type field of IA32_MTRR_PHYSBASEn are 0,1,4,5, and 6. However,
IA32_MTRR_PHYSMASKn don't have type field. This patch avoid check if
the type field is legal for IA32_MTRR_PHYSMASKn.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Current KVM only supports RDMSR for K7_EVNTSEL0 and K7_PERFCTR0
MSRs. Reading the rest MSRs will trigger KVM to inject #GP into
guest VM. This causes a warning message "Failed to access perfctr
msr (MSR c0010001 is ffffffffffffffff)" on AMD host. This patch
adds RDMSR support for all K7_EVNTSELn and K7_PERFCTRn registers
and thus supresses the warning message.
Signed-off-by: Wei Huang <wehuang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
they had small conflicts (respectively within KVM documentation,
and with 3.16-rc changes). Since they were all within the subsystem,
I took care of them.
Stephen Rothwell reported some snags in PPC builds, but they are all
fixed now; the latest linux-next report was clean.
New features for ARM include:
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
And for PPC:
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S HV: Add in-guest debug support
This release drops support for KVM on the PPC440. As a result, the
PPC merge removes more lines than it adds. :)
I also included an x86 change, since Davidlohr tied it to an independent
bug report and the reporter quickly provided a Tested-by; there was no
reason to wait for -rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hyQP
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second round of KVM changes from Paolo Bonzini:
"Here are the PPC and ARM changes for KVM, which I separated because
they had small conflicts (respectively within KVM documentation, and
with 3.16-rc changes). Since they were all within the subsystem, I
took care of them.
Stephen Rothwell reported some snags in PPC builds, but they are all
fixed now; the latest linux-next report was clean.
New features for ARM include:
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
And for PPC:
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S HV: Add in-guest debug support
This release drops support for KVM on the PPC440. As a result, the
PPC merge removes more lines than it adds. :)
I also included an x86 change, since Davidlohr tied it to an
independent bug report and the reporter quickly provided a Tested-by;
there was no reason to wait for -rc2"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (122 commits)
KVM: Move more code under CONFIG_HAVE_KVM_IRQFD
KVM: nVMX: fix "acknowledge interrupt on exit" when APICv is in use
KVM: nVMX: Fix nested vmexit ack intr before load vmcs01
KVM: PPC: Enable IRQFD support for the XICS interrupt controller
KVM: Give IRQFD its own separate enabling Kconfig option
KVM: Move irq notifier implementation into eventfd.c
KVM: Move all accesses to kvm::irq_routing into irqchip.c
KVM: irqchip: Provide and use accessors for irq routing table
KVM: Don't keep reference to irq routing table in irqfd struct
KVM: PPC: drop duplicate tracepoint
arm64: KVM: fix 64bit CP15 VM access for 32bit guests
KVM: arm64: GICv3: mandate page-aligned GICV region
arm64: KVM: GICv3: move system register access to msr_s/mrs_s
KVM: PPC: PR: Handle FSCR feature deselects
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
KVM: PPC: Remove DCR handling
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Handle magic page in kvmppc_ld/st
...
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
Highlights in this release include:
- BookE: Rework instruction fetch, not racy anymore now
- BookE HV: Fix ONE_REG accessors for some in-hardware registers
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S: Some misc bug fixes
- Book3S HV: Add in-guest debug support
- Book3S HV: Preload cache lines on context switch
- Remove 440 support
Alexander Graf (31):
KVM: PPC: Book3s PR: Disable AIL mode with OPAL
KVM: PPC: Book3s HV: Fix tlbie compile error
KVM: PPC: Book3S PR: Handle hyp doorbell exits
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Book3S PR: Fix sparse endian checks
PPC: Add asm helpers for BE 32bit load/store
KVM: PPC: Book3S HV: Make HTAB code LE host aware
KVM: PPC: Book3S HV: Access guest VPA in BE
KVM: PPC: Book3S HV: Access host lppaca and shadow slb in BE
KVM: PPC: Book3S HV: Access XICS in BE
KVM: PPC: Book3S HV: Fix ABIv2 on LE
KVM: PPC: Book3S HV: Enable for little endian hosts
KVM: PPC: Book3S: Move vcore definition to end of kvm_arch struct
KVM: PPC: Deflect page write faults properly in kvmppc_st
KVM: PPC: Book3S: Stop PTE lookup on write errors
KVM: PPC: Book3S: Add hack for split real mode
KVM: PPC: Book3S: Make magic page properly 4k mappable
KVM: PPC: Remove 440 support
KVM: Rename and add argument to check_extension
KVM: Allow KVM_CHECK_EXTENSION on the vm fd
KVM: PPC: Book3S: Provide different CAPs based on HV or PR mode
KVM: PPC: Implement kvmppc_xlate for all targets
KVM: PPC: Move kvmppc_ld/st to common code
KVM: PPC: Remove kvmppc_bad_hva()
KVM: PPC: Use kvm_read_guest in kvmppc_ld
KVM: PPC: Handle magic page in kvmppc_ld/st
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Remove DCR handling
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: PR: Handle FSCR feature deselects
Alexey Kardashevskiy (1):
KVM: PPC: Book3S: Fix LPCR one_reg interface
Aneesh Kumar K.V (4):
KVM: PPC: BOOK3S: PR: Fix PURR and SPURR emulation
KVM: PPC: BOOK3S: PR: Emulate virtual timebase register
KVM: PPC: BOOK3S: PR: Emulate instruction counter
KVM: PPC: BOOK3S: HV: Update compute_tlbie_rb to handle 16MB base page
Anton Blanchard (2):
KVM: PPC: Book3S HV: Fix ABIv2 indirect branch issue
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
Bharat Bhushan (10):
kvm: ppc: bookehv: Added wrapper macros for shadow registers
kvm: ppc: booke: Use the shared struct helpers of SRR0 and SRR1
kvm: ppc: booke: Use the shared struct helpers of SPRN_DEAR
kvm: ppc: booke: Add shared struct helpers of SPRN_ESR
kvm: ppc: booke: Use the shared struct helpers for SPRN_SPRG0-7
kvm: ppc: Add SPRN_EPR get helper function
kvm: ppc: bookehv: Save restore SPRN_SPRG9 on guest entry exit
KVM: PPC: Booke-hv: Add one reg interface for SPRG9
KVM: PPC: Remove comment saying SPRG1 is used for vcpu pointer
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
Michael Neuling (1):
KVM: PPC: Book3S HV: Add H_SET_MODE hcall handling
Mihai Caraman (8):
KVM: PPC: e500mc: Enhance tlb invalidation condition on vcpu schedule
KVM: PPC: e500: Fix default tlb for victim hint
KVM: PPC: e500: Emulate power management control SPR
KVM: PPC: e500mc: Revert "add load inst fixup"
KVM: PPC: Book3e: Add TLBSEL/TSIZE defines for MAS0/1
KVM: PPC: Book3s: Remove kvmppc_read_inst() function
KVM: PPC: Allow kvmppc_get_last_inst() to fail
KVM: PPC: Bookehv: Get vcpu's last instruction for emulation
Paul Mackerras (4):
KVM: PPC: Book3S: Controls for in-kernel sPAPR hypercall handling
KVM: PPC: Book3S: Allow only implemented hcalls to be enabled or disabled
KVM: PPC: Book3S PR: Take SRCU read lock around RTAS kvm_read_guest() call
KVM: PPC: Book3S: Make kvmppc_ld return a more accurate error indication
Stewart Smith (2):
Split out struct kvmppc_vcore creation to separate function
Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJT21skAAoJECszeR4D/txgeFEP/AzJopN7s//W33CfyBqURHXp
XALCyAw+S67gtcaTZbxomcG1xuT8Lj9WEw28iz3rCtAnJwIxsY63xrI1nXMzTaI2
p1rC0ai5Qy+nlEbd6L78spZy/Nzh8DFYGWx78iUSO1mYD8xywJwtoiBA539pwp8j
8N+mgn61Hwhv31bKtsZlmzXymVr/jbTp5LVuxsBLJwD2lgT49g+4uBnX2cG/iXkg
Rzbh7LxoNNXrSPI8sYmTWu/81aeXteeX70ja6DHuV5dWLNTuAXJrh5EUfeAZqBrV
aYcLWUYmIyB87txNmt6ZGVar2p3jr2Xhb9mKx+EN4dbehblanLc1PUqlHd0q3dKc
Nt60ByqpZn+qDAK86dShSZLEe+GT3lovvE76CqVXD4Er+OUEkc9JoxhN1cof/Gb0
o6uwZ2isXHRdGoZx5vb4s3UTOlwZGtoL/CyY/HD/ujYDSURkCGbxLj3kkecSY8ut
QdDAWsC15BwsHtKLr5Zwjp2w+0eGq2QJgfvO0zqWFiz9k33SCBCUpwluFeqh27Hi
aR5Wir3j+MIw9G8XlYlDJWYfi0h/SZ4G7hh7jSu26NBNBzQsDa8ow/cLzdMhdUwH
OYSaeqVk5wiRb9to1uq1NQWPA0uRAx3BSjjvr9MCGRqmvn+FV5nj637YWUT+53Hi
aSvg/U2npghLPPG2cihu
=JuLr
-----END PGP SIGNATURE-----
Merge tag 'signed-kvm-ppc-next' of git://github.com/agraf/linux-2.6 into kvm
Patch queue for ppc - 2014-08-01
Highlights in this release include:
- BookE: Rework instruction fetch, not racy anymore now
- BookE HV: Fix ONE_REG accessors for some in-hardware registers
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S: Some misc bug fixes
- Book3S HV: Add in-guest debug support
- Book3S HV: Preload cache lines on context switch
- Remove 440 support
Alexander Graf (31):
KVM: PPC: Book3s PR: Disable AIL mode with OPAL
KVM: PPC: Book3s HV: Fix tlbie compile error
KVM: PPC: Book3S PR: Handle hyp doorbell exits
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Book3S PR: Fix sparse endian checks
PPC: Add asm helpers for BE 32bit load/store
KVM: PPC: Book3S HV: Make HTAB code LE host aware
KVM: PPC: Book3S HV: Access guest VPA in BE
KVM: PPC: Book3S HV: Access host lppaca and shadow slb in BE
KVM: PPC: Book3S HV: Access XICS in BE
KVM: PPC: Book3S HV: Fix ABIv2 on LE
KVM: PPC: Book3S HV: Enable for little endian hosts
KVM: PPC: Book3S: Move vcore definition to end of kvm_arch struct
KVM: PPC: Deflect page write faults properly in kvmppc_st
KVM: PPC: Book3S: Stop PTE lookup on write errors
KVM: PPC: Book3S: Add hack for split real mode
KVM: PPC: Book3S: Make magic page properly 4k mappable
KVM: PPC: Remove 440 support
KVM: Rename and add argument to check_extension
KVM: Allow KVM_CHECK_EXTENSION on the vm fd
KVM: PPC: Book3S: Provide different CAPs based on HV or PR mode
KVM: PPC: Implement kvmppc_xlate for all targets
KVM: PPC: Move kvmppc_ld/st to common code
KVM: PPC: Remove kvmppc_bad_hva()
KVM: PPC: Use kvm_read_guest in kvmppc_ld
KVM: PPC: Handle magic page in kvmppc_ld/st
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Remove DCR handling
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: PR: Handle FSCR feature deselects
Alexey Kardashevskiy (1):
KVM: PPC: Book3S: Fix LPCR one_reg interface
Aneesh Kumar K.V (4):
KVM: PPC: BOOK3S: PR: Fix PURR and SPURR emulation
KVM: PPC: BOOK3S: PR: Emulate virtual timebase register
KVM: PPC: BOOK3S: PR: Emulate instruction counter
KVM: PPC: BOOK3S: HV: Update compute_tlbie_rb to handle 16MB base page
Anton Blanchard (2):
KVM: PPC: Book3S HV: Fix ABIv2 indirect branch issue
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
Bharat Bhushan (10):
kvm: ppc: bookehv: Added wrapper macros for shadow registers
kvm: ppc: booke: Use the shared struct helpers of SRR0 and SRR1
kvm: ppc: booke: Use the shared struct helpers of SPRN_DEAR
kvm: ppc: booke: Add shared struct helpers of SPRN_ESR
kvm: ppc: booke: Use the shared struct helpers for SPRN_SPRG0-7
kvm: ppc: Add SPRN_EPR get helper function
kvm: ppc: bookehv: Save restore SPRN_SPRG9 on guest entry exit
KVM: PPC: Booke-hv: Add one reg interface for SPRG9
KVM: PPC: Remove comment saying SPRG1 is used for vcpu pointer
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
Michael Neuling (1):
KVM: PPC: Book3S HV: Add H_SET_MODE hcall handling
Mihai Caraman (8):
KVM: PPC: e500mc: Enhance tlb invalidation condition on vcpu schedule
KVM: PPC: e500: Fix default tlb for victim hint
KVM: PPC: e500: Emulate power management control SPR
KVM: PPC: e500mc: Revert "add load inst fixup"
KVM: PPC: Book3e: Add TLBSEL/TSIZE defines for MAS0/1
KVM: PPC: Book3s: Remove kvmppc_read_inst() function
KVM: PPC: Allow kvmppc_get_last_inst() to fail
KVM: PPC: Bookehv: Get vcpu's last instruction for emulation
Paul Mackerras (4):
KVM: PPC: Book3S: Controls for in-kernel sPAPR hypercall handling
KVM: PPC: Book3S: Allow only implemented hcalls to be enabled or disabled
KVM: PPC: Book3S PR: Take SRCU read lock around RTAS kvm_read_guest() call
KVM: PPC: Book3S: Make kvmppc_ld return a more accurate error indication
Stewart Smith (2):
Split out struct kvmppc_vcore creation to separate function
Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8
Conflicts:
Documentation/virtual/kvm/api.txt
few days.
MIPS and s390 have little going on this release; just bugfixes, some
small, some larger.
The highlights for x86 are nested VMX improvements (Jan Kiszka), optimizations
for old processor (up to Nehalem, by me and Bandan Das), and a lot of x86
emulator bugfixes (Nadav Amit).
Stephen Rothwell reported a trivial conflict with the tracing branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=UXxV
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM changes from Paolo Bonzini:
"These are the x86, MIPS and s390 changes; PPC and ARM will come in a
few days.
MIPS and s390 have little going on this release; just bugfixes, some
small, some larger.
The highlights for x86 are nested VMX improvements (Jan Kiszka),
optimizations for old processor (up to Nehalem, by me and Bandan Das),
and a lot of x86 emulator bugfixes (Nadav Amit).
Stephen Rothwell reported a trivial conflict with the tracing branch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (104 commits)
x86/kvm: Resolve shadow warnings in macro expansion
KVM: s390: rework broken SIGP STOP interrupt handling
KVM: x86: always exit on EOIs for interrupts listed in the IOAPIC redir table
KVM: vmx: remove duplicate vmx_mpx_supported() prototype
KVM: s390: Fix memory leak on busy SIGP stop
x86/kvm: Resolve shadow warning from min macro
kvm: Resolve missing-field-initializers warnings
Replace NR_VMX_MSR with its definition
KVM: x86: Assertions to check no overrun in MSR lists
KVM: x86: set rflags.rf during fault injection
KVM: x86: Setting rflags.rf during rep-string emulation
KVM: x86: DR6/7.RTM cannot be written
KVM: nVMX: clean up nested_release_vmcs12 and code around it
KVM: nVMX: fix lifetime issues for vmcs02
KVM: x86: Defining missing x86 vectors
KVM: x86: emulator injects #DB when RFLAGS.RF is set
KVM: x86: Cleanup of rflags.rf cleaning
KVM: x86: Clear rflags.rf on emulated instructions
KVM: x86: popf emulation should not change RF
KVM: x86: Clearing rflags.rf upon skipped emulated instruction
...
In preparation to make the check_extension function available to VM scope
we add a struct kvm * argument to the function header and rename the function
accordingly. It will still be called from the /dev/kvm fd, but with a NULL
argument for struct kvm *.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Currently there is no check whether shared MSRs list overrun the allocated size
which can results in bugs. In addition there is no check that vmx->guest_msrs
has sufficient space to accommodate all the VMX msrs. This patch adds the
assertions.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86 does not automatically set rflags.rf during event injection. This patch
does partial job, setting rflags.rf upon fault injection. It does not handle
the setting of RF upon interrupt injection on rep-string instruction.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The members of the new struct are the required ones for the new NMI
safe accessor to clcok monotonic. In order to reuse the existing
timekeeping code and to make the update of the fast NMI safe
timekeepers a simple memcpy use the struct for the timekeeper as well
and convert all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
cycle_last was added to the clocksource to support the TSC
validation. We moved that to the core code, so we can get rid of the
extra copy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Convert the relevant base data right away to nanoseconds instead of
doing the conversion on every readout. Reduces text size by 160 bytes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Use the new nanoseconds based interface and get rid of the timespec
conversion dance.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Haswell and newer Intel CPUs have support for RTM, and in that case DR6.RTM is
not fixed to 1 and DR7.RTM is not fixed to zero. That is not the case in the
current KVM implementation. This bug is apparent only if the MOV-DR instruction
is emulated or the host also debugs the guest.
This patch is a partial fix which enables DR6.RTM and DR7.RTM to be cleared and
set respectively. It also sets DR6.RTM upon every debug exception. Obviously,
it is not a complete fix, as debugging of RTM is still unsupported.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the RFLAGS.RF is set, then no #DB should occur on instruction breakpoints.
However, the KVM emulator injects #DB regardless to RFLAGS.RF. This patch fixes
this behavior. KVM, however, still appears not to update RFLAGS.RF correctly,
regardless of this patch.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When skipping an emulated instruction, rflags.rf should be cleared as it would
be on real x86 CPU.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Emulator accesses are always done a page at a time, either by the emulator
itself (for fetches) or because we need to query the MMU for address
translations. Speed up these accesses by using kvm_read_guest_page
and, in the case of fetches, by inlining kvm_read_guest_virt_helper and
dropping the loop around kvm_read_guest_page.
This final tweak saves 30-100 more clock cycles (4-10%), bringing the
count (as measured by kvm-unit-tests) down to 720-1100 clock cycles on
a Sandy Bridge Xeon host, compared to 2300-3200 before the whole series
and 925-1700 after the first two low-hanging fruit changes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Core emulator functions all belong in emulator.c,
x86 should have no knowledge of emulator internals
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Despite the provisions to emulate up to 130 consecutive instructions, in
practice KVM will emulate just one before exiting handle_invalid_guest_state,
because x86_emulate_instruction always sets KVM_REQ_EVENT.
However, we only need to do this if an interrupt could be injected,
which happens a) if an interrupt shadow bit (STI or MOV SS) has gone
away; b) if the interrupt flag has just been set (other instructions
than STI can set it without enabling an interrupt shadow).
This cuts another 700-900 cycles from the cost of emulating an
instruction (measured on a Sandy Bridge Xeon: 1650-2600 cycles
before the patch on kvm-unit-tests, 925-1700 afterwards).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the next patch we will need to know the full state of the
interrupt shadow; we will then set KVM_REQ_EVENT when one bit
is cleared.
However, right now get_interrupt_shadow only returns the one
corresponding to the emulated instruction, or an unconditional
0 if the emulated instruction does not have an interrupt shadow.
This is confusing and does not allow us to check for cleared
bits as mentioned above.
Clean the callback up, and modify toggle_interruptibility to
match the comment above the call. As a small result, the
call to set_interrupt_shadow will be skipped in the common
case where int_shadow == 0 && mask == 0.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 575203 the MCE subsystem in the Linux kernel for AMD sets bit 18
in MSR_K7_HWCR. Running such a kernel as a guest in KVM on an AMD host results
in a GPE injected into the guest because kvm_set_msr_common returns 1. This
patch fixes this by masking bit 18 from the MSR value desired by the guest.
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We encountered a scenario in which after an INIT is delivered, a pending
interrupt is delivered, although it was sent before the INIT. As the SDM
states in section 10.4.7.1, the ISR and the IRR should be cleared after INIT as
KVM does. This also means that pending interrupts should be cleared. This
patch clears upon reset (and INIT) the pending interrupts; and at the same
occassion clears the pending exceptions, since they may cause a similar issue.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I've observed kvmclock being marked as unstable on a modern
single-socket system with a stable TSC and qemu-1.6.2 or qemu-2.0.0.
The culprit was failure in TSC matching because of overflow of
kvm_arch::nr_vcpus_matched_tsc in case there were multiple TSC writes
in a single synchronization cycle.
Turns out that qemu does multiple TSC writes during init, below is the
evidence of that (qemu-2.0.0):
The first one:
0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel]
0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm]
0xffffffffa04cfd6b : kvm_arch_vcpu_postcreate+0x4b/0x80 [kvm]
0xffffffffa04b8188 : kvm_vm_ioctl+0x418/0x750 [kvm]
The second one:
0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel]
0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm]
0xffffffffa090610d : vmx_set_msr+0x29d/0x350 [kvm_intel]
0xffffffffa04be83b : do_set_msr+0x3b/0x60 [kvm]
0xffffffffa04c10a8 : msr_io+0xc8/0x160 [kvm]
0xffffffffa04caeb6 : kvm_arch_vcpu_ioctl+0xc86/0x1060 [kvm]
0xffffffffa04b6797 : kvm_vcpu_ioctl+0xc7/0x5a0 [kvm]
#0 kvm_vcpu_ioctl at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1780
#1 kvm_put_msrs at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1270
#2 kvm_arch_put_registers at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1909
#3 kvm_cpu_synchronize_post_init at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1641
#4 cpu_synchronize_post_init at /build/buildd/qemu-2.0.0+dfsg/include/sysemu/kvm.h:330
#5 cpu_synchronize_all_post_init () at /build/buildd/qemu-2.0.0+dfsg/cpus.c:521
#6 main at /build/buildd/qemu-2.0.0+dfsg/vl.c:4390
The third one:
0xffffffffa08ff2b4 : vmx_write_tsc_offset+0xa4/0xb0 [kvm_intel]
0xffffffffa04c9c05 : kvm_write_tsc+0x1a5/0x360 [kvm]
0xffffffffa090610d : vmx_set_msr+0x29d/0x350 [kvm_intel]
0xffffffffa04be83b : do_set_msr+0x3b/0x60 [kvm]
0xffffffffa04c10a8 : msr_io+0xc8/0x160 [kvm]
0xffffffffa04caeb6 : kvm_arch_vcpu_ioctl+0xc86/0x1060 [kvm]
0xffffffffa04b6797 : kvm_vcpu_ioctl+0xc7/0x5a0 [kvm]
#0 kvm_vcpu_ioctl at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1780
#1 kvm_put_msrs at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1270
#2 kvm_arch_put_registers at /build/buildd/qemu-2.0.0+dfsg/target-i386/kvm.c:1909
#3 kvm_cpu_synchronize_post_reset at /build/buildd/qemu-2.0.0+dfsg/kvm-all.c:1635
#4 cpu_synchronize_post_reset at /build/buildd/qemu-2.0.0+dfsg/include/sysemu/kvm.h:323
#5 cpu_synchronize_all_post_reset () at /build/buildd/qemu-2.0.0+dfsg/cpus.c:512
#6 main at /build/buildd/qemu-2.0.0+dfsg/vl.c:4482
The fix is to count each vCPU only once when matched, so that
nr_vcpus_matched_tsc holds the size of the matched set. This is
achieved by reusing generation counters. Every vCPU with
this_tsc_generation == cur_tsc_generation is in the matched set. The
match set is cleared by setting cur_tsc_generation to a value which no
other vCPU is set to (by incrementing it).
I needed to bump up the counter size form u8 to u64 to ensure it never
overflows. Otherwise in cases TSC is not written the same number of
times on each vCPU the counter could overflow and incorrectly indicate
some vCPUs as being in the matched set. This scenario seems unlikely
but I'm not sure if it can be disregarded.
Signed-off-by: Tomasz Grabiec <tgrabiec@cloudius-systems.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With commit b6b8a1451f that introduced
vmx_check_nested_events, checks for injectable interrupts happen
at different points in time for L1 and L2 that could potentially
cause a race. The regression occurs because KVM_REQ_EVENT is always
set when nested_run_pending is set even if there's no pending interrupt.
Consequently, there could be a small window when check_nested_events
returns without exiting to L1, but an interrupt comes through soon
after and it incorrectly, gets injected to L2 by inject_pending_event
Fix this by adding a call to check for nested events too when a check
for injectable interrupt returns true
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
