Some irq_chips need to know the state of wakeup mode for
setting the trigger type etc. Reflect it in irq_data state.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_chips, which require to mask the chip before changing the trigger
type should set this flag. So the core takes care of it and the
requirement for looking into desc->status in the chip goes away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Looking through irq_chip implementations I noticed that some of them
have special requirements, like setting the type masked and therefor
fiddle in irq_desc->status. Add a flag field, so the core code can
handle it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
That's the data structure chip functions get provided. Also allow them
to signal the core code that they updated the flags in irq_data.state
by returning IRQ_SET_MASK_OK_NOCOPY. The default is unchanged.
The type bits should be accessed via:
val = irqd_get_trigger_type(irqdata);
and
irqd_set_trigger_type(irqdata, val);
Coders who access them directly will be tracked down and slapped with
stinking trouts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
That's the right data structure to look at for arch code.
Accessor functions are provided.
irqd_is_per_cpu(irqdata);
irqd_can_balance(irqdata);
Coders who access them directly will be tracked down and slapped with
stinking trouts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Its' too ugly and needs to go. The only users are core code and
parisc. Core code does not need it and parisc gets a new check once
IRQ_PER_CPU is reflected in irq_data.state.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The saving of this switch is minimal versus the ifdef mess it
creates. Simple enable PER_CPU unconditionally and remove the config
switch.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
chip implementations need to know about it. Keep status in sync until
all users are fixed.
Accessor function: irqd_is_setaffinity_pending(irqdata)
Coders who access them directly will be tracked down and slapped with
stinking trouts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some chip implementations need to access certain status flags. With
sparse irqs that requires a lookup of the irq descriptor. Add a state
field which contains such flags.
Name it in a way which will make coders happy to access it with the
proper accessor functions. And it's easy to grep for.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need to maintain the flag for now in both fields status and istate.
Add a CONFIG_GENERIC_HARDIRQS_NO_COMPAT switch to allow testing w/o
the status one. Wrap the access to status IRQ_INPROGRESS in a inline
which can be turned of with CONFIG_GENERIC_HARDIRQS_NO_COMPAT along
with the define.
There is no reason that anything outside of core looks at this. That
needs some modifications, but we'll get there.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With the chip.end() function gone we might run into a situation where
a poll call runs and the real interrupt comes in, sees IRQ_INPROGRESS
and disables the line. That might be a perfect working one, which will
then be masked forever.
So mark them polled while the poll runs. When the real handler sees
IRQ_INPROGRESS it checks the poll flag and waits for the polling to
complete. Add the necessary amount of sanity checks to it to avoid
deadlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While rumaging through arch code I found that there are a few
workarounds which deal with the fact that the initial affinity setting
from request_irq() copies the mask into irq_data->affinity before the
chip code is called. In the normal path we unconditionally copy the
mask when the chip code returns 0.
Copy after the code is called and add a return code
IRQ_SET_MASK_OK_NOCOPY for the chip functions, which prevents the
copy. That way we see the real mask when the chip function decided to
truncate it further as some arches do. IRQ_SET_MASK_OK is 0, which is
the current behaviour.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The irq namespace has become quite convoluted. My bad. Clean it up
and deprecate the old functions. All new functions follow the scheme:
irq number based:
irq_set/get/xxx/_xxx(unsigned int irq, ...)
irq_data based:
irq_data_set/get/xxx/_xxx(struct irq_data *d, ....)
irq_desc based:
irq_desc_get_xxx(struct irq_desc *desc)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The mask which filters out the valid bits which can be set via
irq_modify_status() is missing IRQ_NO_BALANCING, which breaks UV.
Add IRQ_PER_CPU as well to avoid another one line patch for 39.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For cases that wish to reserve a single IRQ at a given place simply
provide a wrapper in to the ranged reservation routine.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
LKML-Reference: <20101026071912.GD4733@linux-sh.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the cleanup functions of the dynamic allocator. No need to have
separate implementations.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
irq_2_iommu is now in the x86 code where it belongs. Remove all
leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
sparse irq sets up NR_IRQS_LEGACY irq descriptors and archs then go
ahead and allocate more.
Use the unused return value of arch_probe_nr_irqs() to let the
architecture return the number of early allocations. Fix up all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Mark a range of interrupts as allocated. In the SPARSE_IRQ=n case we
need this to update the bitmap for the legacy irqs so the enumerator
via irq_get_next_irq() works.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current sparse_irq allocator has several short comings due to
failures in the design or the lack of it:
- Requires iteration over the number of active irqs to find a free slot
(Some architectures have grown their own workarounds for this)
- Removal of entries is not possible
- Racy between create_irq_nr and destroy_irq (plugged by horrible
callbacks)
- Migration of active irq descriptors is not possible
- No bulk allocation of irq ranges
- Sprinkeled irq_desc references all over the place outside of kernel/irq/
(The previous chip functions series is addressing this issue)
Implement a sane allocator which fixes the above short comings (though
migration of active descriptors needs a full tree wide cleanup of the
direct and mostly unlocked access to irq_desc).
The new allocator still uses a radix_tree, but uses a bitmap for
keeping track of allocated irq numbers. That allows:
- Fast lookup of a free slot
- Allows the removal of descriptors
- Prevents the create/destroy race
- Bulk allocation of consecutive irq ranges
- Basic design is ready for migration of life descriptors after
further cleanups
The bitmap is also used in the SPARSE_IRQ=n case for lookup and
raceless (de)allocation of irq numbers. So it removes the requirement
for looping through the descriptor array to find slots.
Right now it uses sparse_irq_lock to protect the bitmap and the radix
tree, but after cleaning up all users we should be able convert that
to a mutex and to switch the radix_tree and decriptor allocations to
GFP_KERNEL.
[ Folded in a bugfix from Yinghai Lu ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Arch code sets it's own irq_desc.status flags right after boot and for
dynamically allocated interrupts. That might involve iterating over a
huge array.
Allow ARCH_IRQ_INIT_FLAGS to set separate flags aside of IRQ_DISABLED
which is the default.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Get the data structure from the core and provide inline wrappers to
access the irq_data members.
Provide accessor inlines for irq_data as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Provide a irq_desc.status modifier function to cleanup the direct
access to irq_desc in arch and driver code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
move_irq() has no users. Remove it and simplify the ifdef forrest while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
This option covers now the old chip functions and the irq_desc data
fields which are moving to struct irq_data. More stuff will follow.
Pretty handy for testing a conversion, whether something broke or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The low level irq chip functions want access to irq_desc->irq_data.
Provide new functions which hand down irq_data instead of the irq
number so these functions avoid to call irq_to_desc() which is a radix
tree lookup in case of sparse irq.
This provides all the old functions except one: end(). end() is a
relict of __do_IRQ() and will just go away with the __do_IRQ() code.
The replacement for set_affinity() has an extra argument "bool
force". The reason for this is to notify the low level code, that the
move has to be done right away and cannot be delayed until the next
interrupt happens. That's necessary to handle the irq fixup on cpu
unplug in the generic code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121841.742126604@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Convert all references in the core code to orq, chip, handler_data,
chip_data, msi_desc, affinity to irq_data.*
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Low level chip functions need access to irq_desc->handler_data,
irq_desc->chip_data and irq_desc->msi_desc. We hand down the irq
number to the low level functions, so they need to lookup irq_desc.
With sparse irq this means a radix tree lookup.
We could hand down irq_desc itself, but low level chip functions have
no need to fiddle with it directly and we want to restrict access to
irq_desc further.
Preparatory patch for new chip functions.
Note, that the ugly anon union/struct is there to avoid a full tree
wide clean up for now. This is not going to last 3 years like __do_IRQ()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121841.645542300@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
3 years transition phase is enough. Cleanup the last users and remove
the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Leo Chen <leochen@broadcom.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
This patch adds a cpumask affinity hint to the irq_desc structure,
along with a registration function and a read-only proc entry for each
interrupt.
This affinity_hint handle for each interrupt can be used by underlying
drivers that need a better mechanism to control interrupt affinity.
The underlying driver can register a cpumask for the interrupt, which
will allow the driver to provide the CPU mask for the interrupt to
anything that requests it. The intent is to extend the userspace
daemon, irqbalance, to help hint to it a preferred CPU mask to balance
the interrupt into.
[ tglx: Fixed compile warnings, added WARN_ON, made SMP only ]
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: davem@davemloft.net
Cc: arjan@linux.jf.intel.com
Cc: bhutchings@solarflare.com
LKML-Reference: <20100430214445.3992.41647.stgit@ppwaskie-hc2.jf.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
x86: Fix out of order of gsi
x86: apic: Fix mismerge, add arch_probe_nr_irqs() again
x86, irq: Keep chip_data in create_irq_nr and destroy_irq
xen: Remove unnecessary arch specific xen irq functions.
smp: Use nr_cpus= to set nr_cpu_ids early
x86, irq: Remove arch_probe_nr_irqs
sparseirq: Use radix_tree instead of ptrs array
sparseirq: Change irq_desc_ptrs to static
init: Move radix_tree_init() early
irq: Remove unnecessary bootmem code
x86: Add iMac9,1 to pci_reboot_dmi_table
x86: Convert i8259_lock to raw_spinlock
x86: Convert nmi_lock to raw_spinlock
x86: Convert ioapic_lock and vector_lock to raw_spinlock
x86: Avoid race condition in pci_enable_msix()
x86: Fix SCI on IOAPIC != 0
x86, ia32_aout: do not kill argument mapping
x86, irq: Move __setup_vector_irq() before the first irq enable in cpu online path
x86, irq: Update the vector domain for legacy irqs handled by io-apic
x86, irq: Don't block IRQ0_VECTOR..IRQ15_VECTOR's on all cpu's
...
Keep chip_data in create_irq_nr and destroy_irq.
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
destroy_irq()
dynamic_irq_cleanup() which sets desc->chip_data = NULL
...race window...
desc->chip_data = cfg;
Remove the save and restore code for cfg in create_irq_nr() and
destroy_irq() and take the desc->lock when checking the irq_cfg.
Reported-and-analyzed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Brandon Phililps <bphilips@suse.de>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The documentation says that by default disable() will be
chip->mask but in fact default_disable() is a noop.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
LKML-Reference: <1262698198-30392-1-git-send-email-broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'irq-threaded-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Do not mask oneshot edge type interrupts
genirq: Support nested threaded irq handling
genirq: Add buslock support
genirq: Add oneshot support
The function is supposed to be called from the primary IRQ
handler for a demultiplexing chip so make a protype visible for
them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
LKML-Reference: <1251142084-9852-1-git-send-email-broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Interrupt chips which are behind a slow bus (i2c, spi ...) and
demultiplex other interrupt sources need to run their interrupt
handler in a thread.
The demultiplexed interrupt handlers need to run in thread context as
well and need to finish before the demux handler thread can reenable
the interrupt line. So the easiest way is to run the sub device
handlers in the context of the demultiplexing handler thread.
To avoid that a separate thread is created for the subdevices the
function set_nested_irq_thread() is provided which sets the
IRQ_NESTED_THREAD flag in the interrupt descriptor.
A driver which calls request_threaded_irq() must not be aware of the
fact that the threaded handler is called in the context of the
demultiplexing handler thread. The setup code checks the
IRQ_NESTED_THREAD flag which was set from the irq chip setup code and
does not setup a separate thread for the interrupt. The primary
function which is provided by the device driver is replaced by an
internal dummy function which warns when it is called.
For the demultiplexing handler a helper function handle_nested_irq()
is provided which calls the demux interrupt thread function in the
context of the caller and does the proper interrupt accounting and
takes the interrupt disabled status of the demultiplexed subdevice
into account.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The
bus access needs to sleep and therefor cannot be called in atomic
contexts.
Some of the generic interrupt management functions like disable_irq(),
enable_irq() ... call interrupt chip functions with the irq_desc->lock
held and interrupts disabled. This does not work for such devices.
Provide a separate synchronization mechanism for such interrupt
chips. The irq_chip structure is extended by two optional functions
(bus_lock and bus_sync_and_unlock).
The idea is to serialize the bus access for those operations in the
core code so that drivers which are behind that bus operated interrupt
controller do not have to worry about it and just can use the normal
interfaces. To achieve this we add two function pointers to the
irq_chip: bus_lock and bus_sync_unlock.
bus_lock() is called to serialize access to the interrupt controller
bus.
Now the core code can issue chip->mask/unmask ... commands without
changing the fast path code at all. The chip implementation merily
stores that information in a chip private data structure and
returns. No bus interaction as these functions are called from atomic
context.
After that bus_sync_unlock() is called outside the atomic context. Now
the chip implementation issues the bus commands, waits for completion
and unlocks the interrupt controller bus.
The irq_chip implementation as pseudo code:
struct irq_chip_data {
struct mutex mutex;
unsigned int irq_offset;
unsigned long mask;
unsigned long mask_status;
}
static void bus_lock(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
mutex_lock(&data->mutex);
}
static void mask(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
irq -= data->irq_offset;
data->mask |= (1 << irq);
}
static void unmask(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
irq -= data->irq_offset;
data->mask &= ~(1 << irq);
}
static void bus_sync_unlock(unsigned int irq)
{
struct irq_chip_data *data = get_irq_desc_chip_data(irq);
if (data->mask != data->mask_status) {
do_bus_magic_to_set_mask(data->mask);
data->mask_status = data->mask;
}
mutex_unlock(&data->mutex);
}
The device drivers can use request_threaded_irq, free_irq, disable_irq
and enable_irq as usual with the only restriction that the calls need
to come from non atomic context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
For threaded interrupt handlers we expect the hard interrupt handler
part to mask the interrupt on the originating device. The interrupt
line itself is reenabled after the hard interrupt handler has
executed.
This requires access to the originating device from hard interrupt
context which is not always possible. There are devices which can only
be accessed via a bus (i2c, spi, ...). The bus access requires thread
context. For such devices we need to keep the interrupt line masked
until the threaded handler has executed.
Add a new flag IRQF_ONESHOT which allows drivers to request that the
interrupt is not unmasked after the hard interrupt context handler has
been executed and the thread has been woken. The interrupt line is
unmasked after the thread handler function has been executed.
Note that for now IRQF_ONESHOT cannot be used with IRQF_SHARED to
avoid complex accounting mechanisms.
For oneshot interrupts the primary handler simply returns
IRQ_WAKE_THREAD and does nothing else. A generic implementation
irq_default_primary_handler() is provided to avoid useless copies all
over the place. It is automatically installed when
request_threaded_irq() is called with handler=NULL and
thread_fn!=NULL.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Trilok Soni <soni.trilok@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: m.szyprowski@samsung.com
Cc: t.fujak@samsung.com
Cc: kyungmin.park@samsung.com,
Cc: David Brownell <david-b@pacbell.net>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: arve@android.com
Cc: Barry Song <21cnbao@gmail.com>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t)
have been kept around for migration reasons. The last users are gone,
remove them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq, irq.h: Fix kernel-doc warnings
genirq: fix comment to say IRQ_WAKE_THREAD
Fix kernel-doc warnings in linux/irq.h:
Warning(include/linux/irq.h:201): No description found for parameter 'node'
Warning(include/linux/irq.h:201): Excess struct/union/enum/typedef member 'cpu' description in 'irq_desc'
Warning(include/linux/irq.h:434): No description found for parameter 'node'
Warning(include/linux/irq.h:434): Excess function parameter 'cpu' description in 'alloc_desc_masks'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <4A3467EC.50006@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that we set up the slab allocator earlier, we can get rid of some
alloc_bootmem_cpumask_var() calls in boot code.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
move_irq_desc() will try to move irq_desc to the home node if
the allocated one is not correct, in create_irq_nr().
( This can happen on devices that are on different nodes that
are using MSI, when drivers are loaded and unloaded randomly. )
v2: fix non-smp build
v3: add NUMA_IRQ_DESC to eliminate #ifdefs
[ Impact: improve irq descriptor locality on NUMA systems ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F95EAE.2050903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Try to get irq_desc on the home node in create_irq_nr().
v2: don't check if we can move it when sparse_irq is not used
v3: use move_irq_des, if that node is not what we want
[ Impact: optimization, make MSI IRQ descriptors more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F6559F.7070005@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This simplifies the node awareness of the code. All our allocators
only deal with a NUMA node ID locality not with CPU ids anyway - so
there's no need to maintain (and transform) a CPU id all across the
IRq layer.
v2: keep move_irq_desc related
[ Impact: cleanup, prepare IRQ code to be NUMA-aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49F65536.2020300@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The original feature of migrating irq_desc dynamic was too fragile
and was causing problems: it caused crashes on systems with lots of
cards with MSI-X when user-space irq-balancer was enabled.
We now have new patches that create irq_desc according to device
numa node. This patch removes the leftover bits of the dynamic balancer.
[ Impact: remove dead code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49F654AF.8000808@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CPUMASKS_OFFSTACK is not defined anywhere (it is CPUMASK_OFFSTACK).
It is a typo and init_allocate_desc_masks() is called before it set
affinity to all cpus...
Split init_alloc_desc_masks() into all_desc_masks() and init_desc_masks().
Also use CPUMASK_OFFSTACK in alloc_desc_masks().
[ Impact: fix smp_affinity copying/setup when moving irq_desc between CPUs ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <49F6546E.3040406@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Need to free the old cpumask for affinity and pending_mask.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <49D18FF0.50707@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce helper functions allowing us to prevent device drivers from
getting any interrupts (without disabling interrupts on the CPU)
during suspend (or hibernation) and to make them start to receive
interrupts again during the subsequent resume. These functions make it
possible to keep timer interrupts enabled while the "late" suspend and
"early" resume callbacks provided by device drivers are being
executed. In turn, this allows device drivers' "late" suspend and
"early" resume callbacks to sleep, execute ACPI callbacks etc.
The functions introduced here will be used to rework the handling of
interrupts during suspend (hibernation) and resume. Namely,
interrupts will only be disabled on the CPU right before suspending
sysdevs, while device drivers will be prevented from receiving
interrupts, with the help of the new helper function, before their
"late" suspend callbacks run (and analogously during resume).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
<linux/irq.h> relies on <linux/gfp.h> and <linux/topology.h> having been
included previous. If not, the errors like below will result.
CC arch/mips/mti-malta/malta-int.o
In file included from arch/mips/mti-malta/malta-int.c:25:
include/linux/irq.h: In function ‘init_alloc_desc_masks’:
include/linux/irq.h:444: error: implicit declaration of function ‘cpu_to_node’
include/linux/irq.h:446: error: ‘GFP_ATOMIC’ undeclared (first use in this function)
include/linux/irq.h:446: error: (Each undeclared identifier is reported only once
include/linux/irq.h:446: error: for each function it appears in.)
make[3]: *** [arch/mips/mti-malta/malta-int.o] Error 1
make[2]: *** [arch/mips/mti-malta] Error 2
make[1]: *** [sub-make] Error 2
Fixed by including the two missing headers.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for threaded interrupt handlers:
A device driver can request that its main interrupt handler runs in a
thread. To achive this the device driver requests the interrupt with
request_threaded_irq() and provides additionally to the handler a
thread function. The handler function is called in hard interrupt
context and needs to check whether the interrupt originated from the
device. If the interrupt originated from the device then the handler
can either return IRQ_HANDLED or IRQ_WAKE_THREAD. IRQ_HANDLED is
returned when no further action is required. IRQ_WAKE_THREAD causes
the genirq code to invoke the threaded (main) handler. When
IRQ_WAKE_THREAD is returned handler must have disabled the interrupt
on the device level. This is mandatory for shared interrupt handlers,
but we need to do it as well for obscure x86 hardware where disabling
an interrupt on the IO_APIC level redirects the interrupt to the
legacy PIC interrupt lines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Modify remove_irq() to match setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120551.2926.43942.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add new API
This patch adds a remove_irq() function for releasing
interrupts requested with setup_irq().
Without this patch we have no way of releasing such
interrupts since free_irq() today tries to kfree()
the irqaction passed with setup_irq().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090312120542.2926.56609.sendpatchset@rx1.opensource.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Miller suggested, related to a kstat_irqs related build breakage:
> Either linux/kernel_stat.h provides the kstat_incr_irqs_this_cpu
> interface or linux/irq.h does, not both.
So move them to kernel_stat.h.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix bug where new irq_desc uses old cpumask pointers which are freed.
As Yinghai pointed out, init_copy_one_irq_desc() copies the old desc to
the new desc overwriting the cpumask pointers. Since the old_desc and
the cpumask pointers are freed, then memory corruption will occur if
these old pointers are used.
Move the allocation of these pointers to after the copy.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Impact: reduce memory usage, use new cpumask API.
Replace the affinity and pending_masks with cpumask_var_t's. This adds
to the significant size reduction done with the SPARSE_IRQS changes.
The added functions (init_alloc_desc_masks & init_copy_desc_masks) are
in the include file so they can be inlined (and optimized out for the
!CONFIG_CPUMASKS_OFFSTACK case.) [Naming chosen to be consistent with
the other init*irq functions, as well as the backwards arg declaration
of "from, to" instead of the more common "to, from" standard.]
Includes a slight change to the declaration of struct irq_desc to embed
the pending_mask within ifdef(CONFIG_SMP) to be consistent with other
references, and some small changes to Xen.
Tested: sparse/non-sparse/cpumask_offstack/non-cpumask_offstack/nonuma/nosmp on x86_64
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: virtualization@lists.osdl.org
Cc: xen-devel@lists.xensource.com
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Impact: clean up sparseirq fallout on random.c
Ingo suggested to change some ifdef from SPARSE_IRQ to GENERIC_HARDIRQS
so we could some #ifdef later if all arch support genirq
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
GCC has a bug with __weak alias functions: if the functions are in
the same compilation unit as their call site, GCC can decide to
inline them - and thus rob the linker of the opportunity to override
the weak alias with the real thing.
So move all the IRQ handling related __weak symbols to kernel/irq/chip.c.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix panic on null pointer with sparseirq
Some GCC versions seem to inline the weak global function,
when that function is empty.
Work it around, by making the functions return a (dummy) integer.
Signed-off-by: Yinghai <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
before CONFIG_SPARSE_IRQ age, for_each_irq_desc() sat in irqnr.h and
could be called from generic code.
CONFIG_SPARSE_IRQ breaks this assumption, but SPARSE_IRQ version
for_each_irq_desc() also can move into irqnr.h easily.
Also, this patch unifies CONFIG_SPARSE_IRQ and !CONFIG_SPARSE_IRQ
for_each_irq_desc().
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: improve NUMA handling by migrating irq_desc on smp_affinity changes
if CONFIG_NUMA_MIGRATE_IRQ_DESC is set:
- make irq_desc to go with affinity aka irq_desc moving etc
- call move_irq_desc in irq_complete_move()
- legacy irq_desc is not moved, because they are allocated via static array
for logical apic mode, need to add move_desc_in_progress_in_same_domain,
otherwise it will not be moved ==> also could need two phases to get
irq_desc moved.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Impact: build fix on Alpha
-tip testing found this build failure on the Alpha defconfig:
/home/mingo/tip/fs/proc/stat.c: In function 'show_stat':
/home/mingo/tip/fs/proc/stat.c:48: error: implicit declaration of function 'for_each_irq_desc'
/home/mingo/tip/fs/proc/stat.c:48: error: expected ';' before '{' token
can not use irq_desc() in stat.c on older architectures.
Signed-off-by: Yinghai Lu <yinghai@kernel.orgg>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: new feature
Problem on distro kernels: irq_desc[NR_IRQS] takes megabytes of RAM with
NR_CPUS set to large values. The goal is to be able to scale up to much
larger NR_IRQS value without impacting the (important) common case.
To solve this, we generalize irq_desc[NR_IRQS] to an (optional) array of
irq_desc pointers.
When CONFIG_SPARSE_IRQ=y is used, we use kzalloc_node to get irq_desc,
this also makes the IRQ descriptors NUMA-local (to the site that calls
request_irq()).
This gets rid of the irq_cfg[] static array on x86 as well: irq_cfg now
uses desc->chip_data for x86 to store irq_cfg.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce struct irq_desc size
struct irq_desc: reorder to remove padding on 64bits
shrinks irq_desc to 128 bytes which saves data space & cache lines
On a generic x86_64/SMP build this reduces the reported data size by
64k.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: preserve user-modified affinities on interrupts
Kumar Galak noticed that commit
1840475676 (genirq: Expose default irq
affinity mask (take 3))
overrides an already set affinity setting across a free /
request_irq(). Happens e.g. with ifdown/ifup of a network device.
Change the logic to mark the affinities as set and keep them
intact. This also fixes the unlocked access to irq_desc in
irq_select_affinity() when called from irq_affinity_proc_write()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the irq_desc related iterators out of irq.h, into irqnr.h, also
available via interrupt.h.
This way non-genirq (and even non-hardirq) architectures get the
common definitions and iterators.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no need for irq_desc here. Even for sparse_irq we can
handle this clever in for_each_irq_nr().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This code is not ready, but we need to rip it out instead of rebasing
as we would lose the APIC/IO_APIC unification otherwise.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This has been deprecated for years, the user space irqbalanced utility
works better with numa, has configurable policies, etc...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmai.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also print out irq no in /proc/interrups and /proc/stat in hex, so could
tell bus/dev/func.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when CONFIG_HAVE_SPARSE_IRQ
preallocate some irq_2_iommu entries, and use get_one_free_irq_2_iomm to
get new one and link to irq_desc if needed.
else will use dyn_array or static array.
v2: <= nr_irqs fix
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
change names:
irq_desc() ==> irq_desc_alloc
__irq_desc() ==> irq_desc
Also split a few of the uses in lowlevel x86 code.
v2: need to check if desc is null in smp_irq_move_cleanup
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we could remove some duplicated calling to irq_desc
v2: make sure irq_desc in init/main.c is not used without generic_hardirqs
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are a handful of loops that go from 0 to nr_irqs and use
get_irq_desc() on them. These would allocate all the irq_desc
entries, regardless of the need for them.
Use the smarter for_each_irq_desc() iterator that will only iterate
over the present ones.
v2: make sure arch without GENERIC_HARDIRQS work too
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add an irq_desc accessor that will not allocate any sparse entry
but returns failure if there's no entry present.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
based on Eric's patch ...
together mold it with dyn_array for irq_desc, will allcate kstat_irqs for
nr_irq_desc alltogether if needed. -- at that point nr_cpus is known already.
v2: make sure system without generic_hardirqs works they don't have irq_desc
v3: fix merging
v4: [mingo@elte.hu] fix typo
[ mingo@elte.hu ] irq: build fix
fix:
arch/x86/xen/spinlock.c: In function 'xen_spin_lock_slow':
arch/x86/xen/spinlock.c:90: error: 'struct kernel_stat' has no member named 'irqs'
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
irq_timer_state[] is a NR_IRQS sized array that is a side-by array to
the real irq_desc[] array.
Integrate that field into the (now dynamic) irq_desc dynamic array and
save some RAM.
v2: keep the old way to support arch not support irq_desc
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add CONFIG_HAVE_SPARSE_IRQ to for use condensed array.
Get rid of irq_desc[] array assumptions.
Preallocate 32 irq_desc, and irq_desc() will try to get more.
( No change in functionality is expected anywhere, except the odd build
failure where we missed a code site or where a crossing commit itroduces
new irq_desc[] usage. )
v2: according to Eric, change get_irq_desc() to irq_desc()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Current IRQ affinity interface does not provide a way to set affinity
for the IRQs that will be allocated/activated in the future.
This patch creates /proc/irq/default_smp_affinity that lets users set
default affinity mask for the newly allocated IRQs. Changing the default
does not affect affinity masks for the currently active IRQs, they
have to be changed explicitly.
Updated based on Paul J's comments and added some more documentation.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com>
Cc: pj@sgi.com
Cc: a.p.zijlstra@chello.nl
Cc: tglx@linutronix.de
Cc: rdunlap@xenotime.net
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Uwe Kleine-Koenig has some strange hardware where one of the shared
interrupts can be asserted during boot before the appropriate driver
loads. Requesting the shared irq line from another driver result in a
spurious interrupt storm which finally disables the interrupt line.
I have seen similar behaviour on resume before (the hardware does not
work anymore so I can not verify).
Change the spurious disable logic to increment the disable depth and
mark the interrupt with an extra flag which allows us to reenable the
interrupt when a new driver arrives which requests the same irq
line. In the worst case this will disable the irq again via the
spurious trap, but there is a decent chance that the new driver is the
one which can handle the already asserted interrupt and makes the box
usable again.
Eric Biederman said further: This case also happens on a regular basis
in kdump kernels where we deliberately don't shutdown the hardware
before starting the new kernel. This patch should reduce the need for
using irqpoll in that situation by a small amount.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-and-Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
> Generic code is not supposed to include irq.h. Replace this include
> by linux/hardirq.h instead and add/replace an include of linux/irq.h
> in asm header files where necessary.
> This change should only matter for architectures that make use of
> GENERIC_CLOCKEVENTS.
> Architectures in question are mips, x86, arm, sh, powerpc, uml and sparc64.
>
> I did some cross compile tests for mips, x86_64, arm, powerpc and sparc64.
> This patch fixes also build breakages caused by the include replacement in
> tick-common.h.
I generally dislike adding optional linux/* includes in asm/* includes -
I'm nervous about this causing include loops.
However, there's a separate point to be discussed here.
That is, what interfaces are expected of every architecture in the kernel.
If generic code wants to be able to set the affinity of interrupts, then
that needs to become part of the interfaces listed in linux/interrupt.h
rather than linux/irq.h.
So what I suggest is this approach instead (against Linus' tree of a
couple of days ago) - we move irq_set_affinity() and irq_can_set_affinity()
to linux/interrupt.h, change the linux/irq.h includes to linux/interrupt.h
and include asm/irq_regs.h where needed (asm/irq_regs.h is supposed to be
rarely used include since not much touches the stacked parent context
registers.)
Build tested on ARM PXA family kernels and ARM's Realview platform
kernels which both use genirq.
[ tglx@linutronix.de: add GENERIC_HARDIRQ dependencies ]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
All users are gone, remove definitions and comments referring
to them.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Probing non-ISA interrupts using the handle_percpu_irq as their handle_irq
method may crash the system because handle_percpu_irq does not check
IRQ_WAITING. This for example hits the MIPS Qemu configuration.
This patch provides two helper functions set_irq_noprobe and set_irq_probe to
set rsp. clear the IRQ_NOPROBE flag. The only current caller is MIPS code
but this really belongs into generic code.
As an aside, interrupt probing these days has become a mostly obsolete if not
dangerous art. I think Linux interrupts should be changed to default to
non-probing but that's subject of this patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-and-tested-by: Rob Landley <rob@landley.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add unlocked version for use by irq_chip.set_type handlers which may
wish to change handler to level or edge handler when IRQ type is
changed.
The normal set_irq_handler() call cannot be used because it tries to
take irq_desc.lock which is already held when the irq_chip.set_type
hook is called.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add kernel-doc entry in <linux/irq.h> for:
Warning(linux-2.6.22-git12//include/linux/irq.h:177): No description found for parameter 'last_unhandled'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we handle spurious IRQ activity based upon seeing a lot of
invalid interrupts, and we clear things back on the base of lots of valid
interrupts.
Unfortunately in some cases you get legitimate invalid interrupts caused by
timing asynchronicity between the PCI bus and the APIC bus when disabling
interrupts and pulling other tricks. In this case although the spurious
IRQs are not a problem our unhandled counters didn't clear and they act as
a slow running timebomb. (This is effectively what the serial port/tty
problem that was fixed by clearing counters when registering a handler
showed up)
It's easy enough to add a second parameter - time. This means that if we
see a regular stream of harmless spurious interrupts which are not harming
processing we don't go off and do something stupid like disable the IRQ
after a month of running. OTOH lockups and performance killers show up a
lot more than 10/second
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We noticed a drop in n/w performance due to the irq_desc being cacheline
aligned rather than internode aligned. We see 50% of expected performance
when two e1000 nics local to two different nodes have consecutive irq
descriptors allocated, due to false sharing.
Note that this patch does away with cacheline padding for the UP case, as
it does not seem useful for UP configurations.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux/irq.h uses EINVAL but does not #include linux/errno.h. This results in
the compiler spitting out errors on some files.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces all instances of "set_native_irq_info(irq, mask)"
with "irq_desc[irq].affinity = mask". The latter form is clearer
uses fewer abstractions, and makes access to this field uniform
accross different architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
powerpc gets:
init/main.c: In function `do_basic_setup':
init/main.c:714: warning: implicit declaration of function `init_irq_proc'
but we cannot include linux/irq.h in generic code.
Fix it by moving the declaration into linux/interrupt.h instead.
And make sure all code that defines init_irq_proc() is including
linux/interrupt.h.
And nuke an ifdef-in-C
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that disable_irq() defaults to delayed-disable semantics, the IRQ_DISABLED
flag is not needed anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide funtions to:
- check, whether an interrupt can set the affinity
- pin the interrupt to a given cpu
Necessary for the ability to setup clocksources more flexible (e.g. use the
different HPET channels per CPU)
[akpm@osdl.org: alpha build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a flag so we can prevent the irq balancing of an interrupt. Move the
bits, so we have room for more :)
Necessary for the ability to setup clocksources more flexible (e.g. use the
different HPET channels per CPU)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to be able to get from an irq number to a struct msi_desc.
The msi_desc array in msi.c had several short comings the big one was
that it could not be used outside of msi.c. Using irq_data in struct
irq_desc almost worked except on some architectures irq_data needs to
be used for something else.
So this patch adds a msi_desc pointer to irq_desc, adds the appropriate
wrappers and changes all of the msi code to use them.
The dynamic_irq_init/cleanup code was tweaked to ensure the new
field is left in a well defined state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce desc->name and eliminate the handle_irq_name() hack. Add
set_irq_chip_and_handler_name() to set the flow type and name at once.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Typedef the IRQ flow handler function type.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 8e973fbdf5716b93a0a8c0365be33a31ca0fa351 commit)
Currently msi.c is doing sanity checks that make certain before an irq is
destroyed it has no more users.
By adding irq_has_action I can perform the test is a generic way, instead of
relying on a msi specific data structure.
By performing the core check in dynamic_irq_cleanup I ensure every user of
dynamic irqs has a test present and we don't free resources that are in use.
In msi.c this allows me to kill the attrib.state member of msi_desc and all of
the assciated code to maintain it.
To keep from freeing data structures when irq cleanup code is called to soon
changing dyanamic_irq_cleanup is insufficient because there are msi specific
data structures that are also not safe to free.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because of the nasty way that CONFIG_PCI_MSI was implemented we wound up with
set_irq_info and set_native_irq_info, with move_irq and move_native_irq. Both
functions did the same thing but they were built and called under different
circumstances. Now that the msi hacks are gone we can kill move_irq and
set_irq_info.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the msi support comes a new concept in irq handling, irqs that are
created dynamically at run time.
Currently the msi code allocates irqs backwards. First it allocates a
platform dependent routing value for an interrupt the ``vector'' and then it
figures out from the vector which irq you are on.
This msi backwards allocator suffers from two basic problems. The allocator
suffers because it is trying to do something that is architecture specific in
a generic way making it brittle, inflexible, and tied to tightly to the
architecture implementation. The alloctor also suffers from it's very
backwards nature as it has tied things together that should have no
dependencies.
To solve the basic dynamic irq allocation problem two new architecture
specific functions are added: create_irq and destroy_irq.
create_irq takes no input and returns an unused irq number, that won't be
reused until it is returned to the free poll with destroy_irq. The irq then
can be used for any purpose although the only initial consumer is the msi
code.
destroy_irq takes an irq number allocated with create_irq and returns it to
the free pool.
Making this functionality per architecture increases the simplicity of the irq
allocation code and increases it's flexibility.
dynamic_irq_init() and dynamic_irq_cleanup() are added to automate the
irq_desc initializtion that should happen for dynamic irqs.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently move_native_irq disables and renables the irq we are migrating to
ensure we don't take that irq when we are actually doing the migration
operation. Disabling the irq needs to happen but sometimes doing the work is
move_native_irq is too late.
On x86 with ioapics the irq move sequences needs to be:
edge_triggered:
mask irq.
move irq.
unmask irq.
ack irq.
level_triggered:
mask irq.
ack irq.
move irq.
unmask irq.
We can easily perform the edge triggered sequence, with the current defintion
of move_native_irq. However the level triggered case does not map well. For
that I have added move_masked_irq, to allow me to disable the irqs around both
the ack and the move.
Q: Why have we not seen this problem earlier?
A: The only symptom I have been able to reproduce is that if we change
the vector before acknowleding an irq the wrong irq is acknowledged.
Since we currently are not reprogramming the irq vector during
migration no problems show up.
We have to mask the irq before we acknowledge the irq or else we could
hit a window where an irq is asserted just before we acknowledge it.
Edge triggered irqs do not have this problem because acknowledgements
do not propogate in the same way.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The primary aim of this patchset is to remove maintenances problems caused by
the irq infrastructure. The two big issues I address are an artificially
small cap on the number of irqs, and that MSI assumes vector == irq. My
primary focus is on x86_64 but I have touched other architectures where
necessary to keep them from breaking.
- To increase the number of irqs I modify the code to look at the (cpu,
vector) pair instead of just looking at the vector.
With a large number of irqs available systems with a large irq count no
longer need to compress their irq numbers to fit. Removing a lot of brittle
special cases.
For acpi guys the result is that irq == gsi.
- Addressing the fact that MSI assumes irq == vector takes a few more
patches. But suffice it to say when I am done none of the generic irq code
even knows what a vector is.
In quick testing on a large Unisys x86_64 machine we stumbled over at least
one driver that assumed that NR_IRQS could always fit into an 8 bit number.
This driver is clearly buggy today. But this has become a class of bugs that
it is now much easier to hit.
This patch:
This is a minor space optimization. In practice I don't think this has any
affect because of our alignment constraints and the other fields but there is
not point in chewing up an uncessary word and since we already read the flag
field this should improve the cache hit ratio of the irq handler.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Permit __do_IRQ() to be dispensed with based on a configuration option.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IRQs need refcounting and a state flag to track whether the the IRQ should
be enabled or disabled as a "normal IRQ" source after a series of calls to
{en,dis}able_irq(). For shared IRQs, the IRQ must be enabled so long as at
least one driver needs it active.
Likewise, IRQs need the same support to track whether the IRQ should be
enabled or disabled as a "wakeup event" source after a series of calls to
{en,dis}able_irq_wake(). For shared IRQs, the IRQ must be enabled as a
wakeup source during sleep so long as at least one driver needs it. But
right now they _don't have_ that refcounting ... which means sharing a
wakeup-capable IRQ can't work correctly in some configurations.
This patch adds the refcount and flag mechanisms to set_irq_wake() -- which
is what {en,dis}able_irq_wake() call -- and minimal documentation of what
the irq wake mechanism does.
Drivers relying on the older (broken) "toggle" semantics will trigger a
warning; that'll be a handful of drivers on ARM systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus: "The hacks in kernel/irq/handle.c are really horrid. REALLY
horrid."
They are indeed. Move the dyntick quirks to ARM where they belong.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent interrupt rework introduced bit value conflicts with sparc.
Instead of introducing new architecture flags mess, move the interrupt SA_
flags out of the signal namespace and replace them by interrupt related flags.
This allows to remove the obsolete SA_INTERRUPT flag and clean up the bit
field values.
This patch:
Move the interrupt related SA_ flags out of linux/signal.h and rename them to
IRQF_ . This moves the interrupt related flags out of the signal namespace
and allows to remove the architecture dependencies.
SA_INTERRUPT is not needed by userspace and glibc so it can be removed safely.
The existing SA_ constants are kept for easy transition and will be
removed after a 6 month grace period.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@debian.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Jens Axboe <axboe@suse.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David Howells <dhowells@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
ARM has a couple of really dumb interrupt controllers.
Implement a generic one and fixup the ARM migration. ARM reused
the no_irq_chip for this purpose, but this does not work out
for platforms which are not converted to the new interrupt
type handling model.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up the fastack concept by turning it into fasteoi and introducing the
->eoi() method for chips.
This also allows the cleanup of an i386 EOI quirk - now the quirk is
cleanly separated from the pure ACK implementation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a #define for the mask of the part of IRQ_TYPE that represents the
trigger type. I use that in my in-progress work as I've standardized the
way the irq description in the firmware device-tree get translated to linux
useable things by using those constants. Having this mask to isolate the
"trigger type" part of the flags is useful in a few places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to use the irq-chip and irq-flow abstractions: allow setting
of the chip, the type and provide highlevel handlers for common irq-flows.
[rostedt@goodmis.org: misroute-irq: Don't call desc->chip->end because of edge interrupts]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a fixed up and cleaned up replacement for genirq-msi-fixes.patch,
which should solve the i386 4KSTACKS problem. I also added Ben's idea of
pushing the __do_IRQ() check into generic_handle_irq().
I booted this with MSI enabled, but i only have MSI devices, not MSI-X
devices. I'd still expect MSI-X to work now.
irqchip migration helper: call __do_IRQ() if a descriptor is attached to an
irqtype-style controller. This also fixes MSI-X IRQ handling on i386 and
x86_64.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to disable the automatic enabling of freshly set up irqs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to disable request_irq() for certain interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms that do not have a hardware-assisted hardirq-resend mechanism
to resend them via a softirq-driven IRQ emulation mechanism.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ->retrigger() irq op to consolidate hw_irq_resend() implementations.
(Most architectures had it defined to NOP anyway.)
NOTE: ia64 needs testing. i386 and x86_64 tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the pending_irq_cpumask[NR_IRQS] array and move it into
the irq_desc[NR_IRQS].pending_mask field.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_dir[NR_IRQS] and the smp_affinity_entry[NR_IRQS]
arrays and move them into the irq_desc[] array.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Small cleanups in include/linux/irq.h.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: remove irq_desc_t use from the generic IRQ code, and mark it
obsolete.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i386 defaults to regparm, explicit uses of fastcall are not needed
anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: remove irq_descp() - explicit use of irq_desc[] is shorter and more
readable.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_affinity[NR_IRQS] array and move it into the
irq_desc[NR_IRQS].affinity field.
[akpm@osdl.org: sparc64 build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct the return type of handle_IRQ_event() (inconsistency noticed during
Xen development), and remove redundant declarations. The return type
adjustment required breaking out the definition of irqreturn_t into a
separate header, in order to satisfy current include order dependencies.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On i386, kernel irq balance doesn't work.
1) In function do_irq_balance, after kernel finds the min_loaded cpu but
before calling set_pending_irq to really pin the selected_irq to the
target cpu, kernel does a cpus_and with irq_affinity[selected_irq].
Later on, when the irq is acked, kernel would calls
move_native_irq=>desc->handler->set_affinity to change the irq affinity.
However, every function pointed by
hw_interrupt_type->set_affinity(unsigned int irq, cpumask_t cpumask)
always changes irq_affinity[irq] to cpumask. Next time when recalling
do_irq_balance, it has to do cpu_ands again with
irq_affinity[selected_irq], but irq_affinity[selected_irq] already
becomes one cpu selected by the first irq balance.
2) Function balance_irq in file arch/i386/kernel/io_apic.c has the same
issue.
[akpm@osdl.org: cleanups]
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Uninline some massive IRQ migration functions. Put them in the new
kernel/irq/migration.c.
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thanks to Christoph for doing most of the work.
This allows automatic SMP IRQ affinity assignment other than default "all
interrupts on all CPUs" which is rather expensive. This might be useful if
the hardware can be programmed to distribute interrupts among different
CPUs, like Alpha does.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan's crosscompile page [1] shows, that one regression in 2.6.15-rc is
that the v850 defconfig does no longer compile.
The compile error is:
<-- snip -->
...
CC arch/v850/kernel/setup.o
In file included from /usr/src/ctest/rc/kernel/arch/v850/kernel/setup.c:17:
/usr/src/ctest/rc/kernel/include/linux/irq.h:13:43: asm/smp.h: No such file or directory
make[2]: *** [arch/v850/kernel/setup.o] Error 1
<-- snip -->
The #include <asm/smp.h> in irq.h was intruduced in 2.6.15-rc.
Since include/linux/irq.h needs code from asm/smp.h only in the
CONFIG_SMP=y case and linux/smp.h #include's asm/smp.h only in the
CONFIG_SMP=y case, I'm suggesting this patch to #include <linux/smp.h>
in irq.h.
I've tested the compilation with both CONFIG_SMP=y and CONFIG_SMP=n
on i386.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IRQ_PER_CPU is not used by all architectures. This patch introduces the
macros ARCH_HAS_IRQ_PER_CPU and CHECK_IRQ_PER_CPU() to avoid the generation
of dead code in __do_IRQ().
ARCH_HAS_IRQ_PER_CPU is defined by architectures using IRQ_PER_CPU in their
include/asm_ARCH/irq.h file.
Through grepping the tree I found the following architectures currently use
IRQ_PER_CPU:
cris, ia64, ppc, ppc64 and parisc.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When handling writes to /proc/irq, current code is re-programming rte
entries directly. This is not recommended and could potentially cause
chipset's to lockup, or cause missing interrupts.
CONFIG_IRQ_BALANCE does this correctly, where it re-programs only when the
interrupt is pending. The same needs to be done for /proc/irq handling as well.
Otherwise user space irq balancers are really not doing the right thing.
- Changed pending_irq_balance_cpumask to pending_irq_migrate_cpumask for
lack of a generic name.
- added move_irq out of IRQ_BALANCE, and added this same to X86_64
- Added new proc handler for write, so we can do deferred write at irq
handling time.
- Display of /proc/irq/XX/smp_affinity used to display CPU_MASKALL, instead
it now shows only active cpu masks, or exactly what was set.
- Provided a common move_irq implementation, instead of duplicating
when using generic irq framework.
Tested on i386/x86_64 and ia64 with CONFIG_PCI_MSI turned on and off.
Tested UP builds as well.
MSI testing: tbd: I have cards, need to look for a x-over cable, although I
did test an earlier version of this patch. Will test in a couple days.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Zwane Mwaikambo <zwane@holomorphy.com>
Grudgingly-acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Anyone reporting a stuck IRQ should try these options. Its effectiveness
varies we've found in the Fedora case. Quite a few systems with misdescribed
IRQ routing just work when you use irqpoll. It also fixes up the VIA systems
although thats now fixed with the VIA quirk (which we could just make default
as its what Redmond OS does but Linus didn't like it historically).
A small number of systems have jammed IRQ sources or misdescribes that cause
an IRQ that we have no handler registered anywhere for. In those cases it
doesn't help.
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another rollup of patches which give various symbols static scope
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Chris Wedgwood <cw@f00f.org>
As suggested by Chris, we can make the "just added" method ->release
conditional to UML only (better: to archs requesting it, i.e. only UML
currently), so that other archs don't get this unneeded crud, and if UML
won't need it any more we can kill this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Chris Wedgwood <cw@f00f.org>
Currently UML must explicitly call the UML-specific
free_irq_by_irq_and_dev() for each free_irq call it's done.
This is needed because ->shutdown and/or ->disable are only called when the
last "action" for that irq is removed.
Instead, for UML shared IRQs (UML IRQs are very often, if not always,
shared), for each dev_id some setup is done, which must be cleared on the
release of that fd. For instance, for each open console a new instance
(i.e. new dev_id) of the same IRQ is requested().
Exactly, a fd is stored in an array (pollfds), which is after read by a
host thread and passed to poll(). Each event registered by poll() triggers
an interrupt. So, for each free_irq() we must remove the corresponding
host fd from the table, which we do via this -release() method.
In this patch we add an appropriate hook for this, and remove all uses of
it by pointing the hook to the said procedure; this is safe to do since the
said procedure.
Also some cosmetic improvements are included.
This is heavily based on some work by Chris Wedgwood, which however didn't
get the patch merged for something I'd call a "misunderstanding" (the need
for this patch wasn't cleanly explained, thus adding the generic hook was
felt as undesirable).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
