The INHIBIT_CHARGE status bit means the battery has reached a
pre-programmed charge limit which is some voltage offset below the
target float voltage. This should be reported as a STATUS_FULL rather
than UNKNOWN, fix it.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20230802-pmi8998-charger-fixes-v1-2-a8f1e8b84c1e@linaro.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
These property were intended to allow the power supply to be treated as a
cooling device, however the cooling device interface has been dropped
from the psy core code. They now just duplicate the CURRENT_NOW and
CURRENT_MAX properties and are generally confusing, drop them.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20230802-pmi8998-charger-fixes-v1-1-a8f1e8b84c1e@linaro.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Due to lack of maintenance and stall of development for a few years now,
and since no new features will ever be added upstream, remove support
for OX810 and OX820 restart feature.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When the power supply device being registered supports a temperature
readout, the core registers a thermal zone for it. The thermal core
would register a hwmon device for that unless told otherwise.
When CONFIG_POWER_SUPPLY_HWMON is enabled, the power supply core creates
a hwmon device. This results in a second entry, one which has a better
name than the one registered through the thermal framework. It could
potentially have readouts other than temperature.
To simplify the result, tell the thermal framework to not register a
hwmon device if CONFIG_POWER_SUPPLY_HWMON is enabled. The result is
one hwmon device with all the readings the device supports.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce a list of generic reset sources and use them to export the
power on reason through sysfs. Update the ABI documentation to describe
this new interface.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[Miquel Raynal: Follow-up on Kamel's work, 4 years later]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't populate the read-only array on the stack, instead make it
static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds a check of the FORCE_20PCT bit when getting the precharge
current value.
According to the bit description for the FORCE_20PCT bit, when
FORCE_20PCT is true, the precharge current target is 50% of
what is configured in the IPRECHG bit field.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
* Add new Qualcomm PMI8998/PM660 SMB2 charger
* bq256xx: support systems without thermistors
* cros_pchg: fix peripheral device status after system resume
* axp20x_usb_power: add support for AXP192
* qcom-pon: add support for pm8941
* at91-reset: prepare to expose reset reason to sysfs
* switch all I2C drivers back to use .probe instead of .probe_new
* convert some more DT bindings to YAML
* misc. cleanups
-----BEGIN PGP SIGNATURE-----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=9vtE
-----END PGP SIGNATURE-----
Merge tag 'for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Add new Qualcomm PMI8998/PM660 SMB2 charger
- bq256xx: support systems without thermistors
- cros_pchg: fix peripheral device status after system resume
- axp20x_usb_power: add support for AXP192
- qcom-pon: add support for pm8941
- at91-reset: prepare to expose reset reason to sysfs
- switch all I2C drivers back to use .probe instead of .probe_new
- convert some more DT bindings to YAML
- misc cleanups
* tag 'for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
MAINTAINERS: add documentation file for Microchip SAMA5D2 shutdown controller
dt-bindings: power: reset: atmel,sama5d2-shdwc: convert to yaml
dt-bindings: power: reset: atmel,at91sam9260-shdwc: convert to yaml
power: reset: at91-reset: change the power on reason prototype
power: reset: qcom-pon: add support for pm8941-pon
dt-bindings: power: reset: qcom-pon: define pm8941-pon
power: supply: add Qualcomm PMI8998 SMB2 Charger driver
dt-bindings: power: supply: qcom,pmi8998-charger: add bindings for smb2 driver
power: supply: rt9467: Make charger-enable control as logic level
power: supply: Switch i2c drivers back to use .probe()
power: reset: add HAS_IOPORT dependencies
dt-bindings: power: supply: axp20x: Add AXP192 compatible
power: supply: axp20x_usb_power: Add support for AXP192
power: supply: axp20x_usb_power: Remove variant IDs from VBUS polling check
power: supply: axp20x_usb_power: Use regmap field for VBUS disabling
power: supply: axp20x_usb_power: Use regmap fields for USB BC feature
power: supply: axp20x_usb_power: Use regmap fields for VBUS monitor feature
power: supply: axp20x_usb_power: Simplify USB current limit handling
power: supply: hwmon: constify pointers to hwmon_channel_info
power: supply: twl4030_madc_battery: Refactor twl4030_madc_bat_ext_changed()
...
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
- New Device Support
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
- New Functionality
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
- Fix-ups
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
- Bug Fixes
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues
-----BEGIN PGP SIGNATURE-----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=9kd5
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
- Add support for TI TPS6594/TPS6593/LP8764 PMICs
- Add support for Samsung RT5033 Battery Charger
- Add support for Analog Devices MAX77540 and MAX77541 PMICs
- New Device Support
- Add support for SPI to Rockchip RK808 (and friends)
- Add support for AXP192 PMIC to X-Powers AXP20X
- Add support for AXP313a PMIC to X-Powers AXP20X
- Add support for RK806 to Rockchip RK8XX
- Removed Device Support
- Removed MFD support for Richtek RT5033 Battery
- Fix-ups
- Remove superfluous code
- Switch I2C drivers from .probe_new() to .probe()
- Convert over to managed resources (devm_*(), etc)
- Use dev_err_probe() for returning errors from .probe()
- Add lots of Device Tree bindings / support
- Improve cache efficiency by switching to Maple
- Use own exported namespaces (NS)
- Include missing and remove superfluous headers
- Start using / convert to the new shutdown sys-off API
- Trivial: variable / define renaming
- Make use of of_property_read_reg() when requesting DT 'reg's
- Bug Fixes
- Fix chip revision readout due to incorrect data masking
- Amend incorrect register and mask values used for charger state
- Hide unused functionality at compile time
- Fix resource leaks following error handling routines
- Return correct error values and fix error handling in general
- Repair incorrect device names - used for device matching
- Remedy broken module auto-loading
-----BEGIN PGP SIGNATURE-----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=EmOj
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for TI TPS6594/TPS6593/LP8764 PMICs
- Add support for Samsung RT5033 Battery Charger
- Add support for Analog Devices MAX77540 and MAX77541 PMICs
New Device Support:
- Add support for SPI to Rockchip RK808 (and friends)
- Add support for AXP192 PMIC to X-Powers AXP20X
- Add support for AXP313a PMIC to X-Powers AXP20X
- Add support for RK806 to Rockchip RK8XX
Removed Device Support:
- Removed MFD support for Richtek RT5033 Battery
Fix-ups:
- Remove superfluous code
- Switch I2C drivers from .probe_new() to .probe()
- Convert over to managed resources (devm_*(), etc)
- Use dev_err_probe() for returning errors from .probe()
- Add lots of Device Tree bindings / support
- Improve cache efficiency by switching to Maple
- Use own exported namespaces (NS)
- Include missing and remove superfluous headers
- Start using / convert to the new shutdown sys-off API
- Trivial: variable / define renaming
- Make use of of_property_read_reg() when requesting DT 'reg's
Bug Fixes:
- Fix chip revision readout due to incorrect data masking
- Amend incorrect register and mask values used for charger state
- Hide unused functionality at compile time
- Fix resource leaks following error handling routines
- Return correct error values and fix error handling in general
- Repair incorrect device names - used for device matching
- Remedy broken module auto-loading"
* tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (51 commits)
dt-bindings: mfd: max77541: Add ADI MAX77541/MAX77540
iio: adc: max77541: Add ADI MAX77541 ADC Support
regulator: max77541: Add ADI MAX77541/MAX77540 Regulator Support
dt-bindings: regulator: max77541: Add ADI MAX77541/MAX77540 Regulator
mfd: Switch two more drivers back to use struct i2c_driver::probe
dt-bindings: mfd: samsung,s5m8767: Simplify excluding properties
mfd: stmpe: Only disable the regulators if they are enabled
mfd: max77541: Add ADI MAX77541/MAX77540 PMIC Support
dt-bindings: mfd: gateworks-gsc: Remove unnecessary fan-controller nodes
mfd: core: Use of_property_read_reg() to parse "reg"
mfd: stmfx: Nullify stmfx->vdd in case of error
mfd: stmfx: Fix error path in stmfx_chip_init
mfd: intel-lpss: Add missing check for platform_get_resource
mfd: stpmic1: Add PMIC poweroff via sys-off handler
mfd: stpmic1: Fixup main control register and bits naming
dt-bindings: mfd: qcom,tcsr: Add the compatible for IPQ8074
mfd: tps65219: Add support for soft shutdown via sys-off API
mfd: pm8008: Drop bogus i2c module alias
mfd: pm8008: Fix module autoloading
mfd: tps65219: Add GPIO cell instance
...
It is quite uncommon to use a driver helper with parameters like *pdev
and __iomem *base. It is much cleaner and close to today's standards to
provide the per-device driver structure and then access its
internals. Let's do this with the helper which returns the power on
reason. While we change the parameters, we can as well rename the
function from at91_reset_status() to at91_reset_reason() to be more
accurate with what the helper actually does, and finally because we don't
really need the pdev argument in this helper besides for printing the
reset reason, we can move the dev_info() call into the probe.
All these modifications prepare the introduction of a sysfs entry to
access this information. This way the diff will be much smaller. Thus,
there is no intended functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
For PM8941 we don't have a defined field to store the reset reason.
Support wrapping pwrkey and resin, but without writing the reset
reason.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a driver for the SMB2 charger block found in the Qualcomm PMI8998
and PM660.
This driver is capable of utilising Qualcomm's Automatic Power Source
Detection (APSD) BC1.2 implementation, as well as Automatic Input
Current Limiting (AICL) to configure the maximum input current
limit of DCP (wall) chargers.
Quick Charge is not currently supported.
Most devices using the smb2 charger have a secondary dedicated charger
chip which is used in parallel to enable faster charger without
overheating. However, not all do, as a result to ensure safety until
these are supported, the maximum current is limited to ~1A via the
FAST_CHARGE_CURRENT_CFG register.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The rt5033-battery fuelgauge can't get a status by itself. The rt5033-charger
can, let's get this value.
To get the charger as a "supplier" from the devicetree, the "of_node" needs
to be initiated.
Additionally, in the probe function replace dev_err() with dev_err_probe(),
this will avoid printing an error for -EPROBE_DEFER when the battery driver
probes before the charger driver.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/a2015d257b145108a3ecdf107a3040362c887fc5.1684182964.git.jahau@rocketmail.com
Move struct rt5033_battery from the mfd header into the battery driver because
it's not used by others.
Within struct rt5033_battery, remove the line "struct rt5033_dev *rt5033;"
because it doesn't get used.
In rt5033.h, remove #include <linux/power_supply.h>, it's not necessary
anymore.
In rt5033_battery.c, remove #include <linux/mfd/rt5033.h>, it's not necessary
anymore either. Instead add #include <linux/regmap.h> and
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/736e1cbee257853cb3d1da6f05c184e9a053263b.1684182964.git.jahau@rocketmail.com
This patch adds device driver of Richtek RT5033 PMIC. The driver supports
switching charger. rt5033 charger provides three charging modes. The charging
modes are pre-charge mode, fast charge mode and constant voltage mode. They
vary in charge rate, the charge parameters can be controlled by i2c interface.
Tested-by: Raymond Hackley <raymondhackley@protonmail.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/9556d4ebb30fd321e37aa0eb343554122e4720c9.1684182964.git.jahau@rocketmail.com
The current coding make 'charger-enable-gpio' control as real hardware
level. This conflicts with the default binding example. For driver
behavior, no need to use real hardware level, just logic level is
enough. This change can make this flexibility keep in dts gpio active
level about this pin.
Fixes: 6f7f70e3a8 ("power: supply: rt9467: Add Richtek RT9467 charger driver")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Merge series from Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>:
A "known issue" during implementation of SE DMA for spi geni driver was
that it does DMA map/unmap internally instead of in spi framework.
Current patches remove this hiccup and also clean up code a bit.
Testing revealed no regressions and results with 1000 iterations of
reading from EC showed no loss of performance.
Results
=======
Before - Iteration 999, min=5.10, max=5.17, avg=5.14, ints=25129
After - Iteration 999, min=5.10, max=5.20, avg=5.15, ints=25153
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
led_blink_set[_oneshot]()'s delay_on and delay_off function parameters
are pass by reference, so that hw-blink implementations can report
back the actual achieved delays when the values have been rounded
to something the hw supports.
This is really only interesting for the sysfs API / the timer trigger.
Other triggers don't really care about this and none of the callers of
led_trigger_blink[_oneshot]() do anything with the returned delay values.
Change the led_trigger_blink[_oneshot]() delay parameters to pass-by-value,
there are 2 reasons for this:
1. led_cdev->blink_set() may sleep, while led_trigger_blink() may not.
So on hw where led_cdev->blink_set() sleeps the call needs to be deferred
to a workqueue, in which case the actual achieved delays are unknown
(this is a preparation patch for the deferring).
2. Since the callers don't care about the actual achieved delays, allowing
callers to directly pass a value leads to simpler code for most callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The logic used for power_supply_is_system_supplied() counts all power
supplies and assumes that the system is running from AC if there is
either a non-battery power-supply reporting to be online or if no
power-supplies exist at all.
The second rule is for desktop systems, that don't have any
battery/charger devices. These systems will incorrectly report to be
powered from battery once a device scope power-supply is registered
(e.g. a HID device), since these power-supplies increase the counter.
Apart from HID devices, recent dGPUs provide UCSI power supplies on a
desktop systems. The dGPU by default doesn't have anything plugged in so
it's 'offline'. This makes power_supply_is_system_supplied() return 0
with a count of 1 meaning all drivers that use this get a wrong judgement.
To fix this case adjust the logic to also examine the scope of the power
supply. If the power supply is deemed a device power supply, then don't
count it.
Cc: Evan Quan <Evan.Quan@amd.com>
Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
CHARGE_INHIBITED bit position of the ChargerStatus register is actually
0 not 1. This patch corrects it.
Fixes: feb583e37f ("power: supply: add sbs-charger driver")
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the AXP192. It is most similar to the AXP202 but
the current limits are different and the USB OTG status register
has a different address (0x04 instead of 0x02).
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use an explicit boolean flag instead of a check based on the
variant ID. Since this is the last use of variant IDs in the
driver, also remove the IDs.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The POWER_SUPPLY_PROP_ONLINE property allows controlling the VBUS
enable state on supported PMICs. Switch to regmap fields to reduce
dependence on variant IDs.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace the use of variant IDs with a regmap field, to reduce
dependence on variant IDs.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use regmap fields to describe the VBUS valid bit and VBUS monitor
enable bit. This allows the driver to easily support other chips,
eg. the AXP192, that have the VBUS valid bit in a different register.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Handle the USB current limit with a lookup table and regmap field,
which minimizes code duplication. Invalid or unlimited values are
denoted by -1 entries, and can't be selected from userspace.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Split rk808 into a core and an i2c part in preparation for
SPI support.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> # for RTC
Tested-by: Diederik de Haas <didi.debian@cknow.org> # Rock64, Quartz64 Model A + B
Tested-by: Vincent Legoll <vincent.legoll@gmail.com> # Pine64 QuartzPro64
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-6-sebastian.reichel@collabora.com
Signed-off-by: Lee Jones <lee@kernel.org>
Reduce the amount of output this dev_dbg() statement emits into logs,
otherwise if system software polls the sysfs entry for data and keeps
getting -ENODATA, it could end up filling the logs up.
This does in fact make systemd journald choke, since during boot the
sysfs power supply entries are polled and if journald starts at the
same time, the journal is just being repeatedly filled up, and the
system stops on trying to start journald without booting any further.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695 ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094d ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use mod_delayed_work() instead of separate cancel_delayed_work_sync() +
schedule_delayed_work() calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.
This is just moving a block of text, no functional changes.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa8118 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c5 ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
twl4030_madc_bat_ext_changed() is a wrapper around
"power_supply_changed(psy);" and it has the same prototype.
Remove it, replacing it with making the external_power_changed
callback directly point to power_supply_changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
max17042_external_power_changed() is a wrapper around
"power_supply_changed(psy);" and it has the same prototype.
Remove it, replacing it with making the external_power_changed
callback directly point to power_supply_changed.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Purism Kernel Team <kernel@puri.sm>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
sc27xx_fgu_external_power_changed() dereferences data->battery,
which gets sets in ab8500_btemp_probe() like this:
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
&fgu_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where sc27xx_fgu_external_power_changed() may get called while
data->battery has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in data->battery,
so sc27xx_fgu_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
After this change sc27xx_fgu_external_power_changed() is reduced to just
"power_supply_changed(psy);" and it has the same prototype. While at it
simply replace it with making the external_power_changed callback
directly point to power_supply_changed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
bq25890_charger_external_power_changed() dereferences bq->charger,
which gets sets in bq25890_power_supply_init() like this:
bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0
<snip>
Call Trace:
<TASK>
__power_supply_get_supplier_property+0x19/0x50
class_for_each_device+0xb1/0xe0
power_supply_get_property_from_supplier+0x2e/0x50
bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger]
__power_supply_changed_work+0x30/0x40
class_for_each_device+0xb1/0xe0
power_supply_changed_work+0x5f/0xe0
<snip>
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Cc: stable@vger.kernel.org
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
fuel_gauge_external_power_changed() dereferences info->bat,
which gets sets in axp288_fuel_gauge_probe() like this:
info->bat = devm_power_supply_register(dev, &fuel_gauge_desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 30abb3d079 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
ab8500_btemp_external_power_changed() dereferences di->btemp_psy,
which gets sets in ab8500_btemp_probe() like this:
di->btemp_psy = devm_power_supply_register(dev, &ab8500_btemp_desc,
&psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where ab8500_btemp_external_power_changed() may get called while
di->btemp_psy has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in di->btemp_psy,
so ab8500_btemp_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
And the same applies to ab8500_fg_external_power_changed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
dev_err_probe() already display the error code. There is no need to
duplicate it explicitly in the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Returning an error code from a remove callback makes the driver core
emit a generic (and so little helpful) error message and after that the
error code is ignored and the device unbound.
As gpio_restart_remove() already emits an error message, suppressing the
generic error is no loss.
Then convert to .remove_new() which is equivalent to returning 0
unconditionally in .remove(). See commit 5c5a7680e6 ("platform:
Provide a remove callback that returns no value") for its rational.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When a stylus is removed (or attached) during suspend, the device detach
(or attach) events can be lost. This patch makes the peripheral device
charge driver retrieve the latest status from the EC on resume.
BUG=b:276414488
TEST=Redrix
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
TS_IGNORE is default off in bq256xx chip. For some HW which doesn't have
the NTC, we need to set TS_IGNORE to 1 to make the charge work. The new
"ti,no-thermistor" is introduced to toggle it.
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- power-supply core support for automatic handling of constant
battery data supplied by firmware
- generic-adc-battery: major cleanup
- axp288_charger: fix ACPI issues on x86 Android tablets
- rk817: cleanup and fix handling for low state of charge
-----BEGIN PGP SIGNATURE-----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=hWo9
-----END PGP SIGNATURE-----
Merge tag 'for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- power-supply core support for automatic handling of constant battery
data supplied by firmware
- generic-adc-battery: major cleanup
- axp288_charger: fix ACPI issues on x86 Android tablets
- rk817: cleanup and fix handling for low state of charge
* tag 'for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (26 commits)
power: supply: rk817: Fix low SOC bugs
power: supply: rk817: Drop unneeded debugging code
power: supply: axp288_charger: Use alt usb-id extcon on some x86 android tablets
power: supply: generic-adc-battery: style fixes
power: supply: generic-adc-battery: improve error message
power: supply: generic-adc-battery: update copyright info
power: supply: generic-adc-battery: add DT support
power: supply: generic-adc-battery: add temperature support
power: supply: generic-adc-battery: simplify read_channel logic
power: supply: generic-adc-battery: use simple-battery API
power: supply: generic-adc-battery: drop memory alloc error message
power: supply: generic-adc-battery: drop charge now support
power: supply: generic-adc-battery: drop jitter delay support
power: supply: generic-adc-battery: fix unit scaling
power: supply: generic-adc-battery: convert to managed resources
power: supply: core: auto-exposure of simple-battery data
dt-bindings: power: supply: adc-battery: add binding
power: supply: bq256xx: Support to disable charger
power: supply: charger-manager: Use of_property_read_bool() for boolean properties
power: reset: qcom-pon: drop of_match_ptr for ID table
...
The summary of the changes for this pull requests is:
* Song Liu's new struct module_memory replacement
* Nick Alcock's MODULE_LICENSE() removal for non-modules
* My cleanups and enhancements to reduce the areas where we vmalloc
module memory for duplicates, and the respective debug code which
proves the remaining vmalloc pressure comes from userspace.
Most of the changes have been in linux-next for quite some time except
the minor fixes I made to check if a module was already loaded
prior to allocating the final module memory with vmalloc and the
respective debug code it introduces to help clarify the issue. Although
the functional change is small it is rather safe as it can only *help*
reduce vmalloc space for duplicates and is confirmed to fix a bootup
issue with over 400 CPUs with KASAN enabled. I don't expect stable
kernels to pick up that fix as the cleanups would have also had to have
been picked up. Folks on larger CPU systems with modules will want to
just upgrade if vmalloc space has been an issue on bootup.
Given the size of this request, here's some more elaborate details
on this pull request.
The functional change change in this pull request is the very first
patch from Song Liu which replaces the struct module_layout with a new
struct module memory. The old data structure tried to put together all
types of supported module memory types in one data structure, the new
one abstracts the differences in memory types in a module to allow each
one to provide their own set of details. This paves the way in the
future so we can deal with them in a cleaner way. If you look at changes
they also provide a nice cleanup of how we handle these different memory
areas in a module. This change has been in linux-next since before the
merge window opened for v6.3 so to provide more than a full kernel cycle
of testing. It's a good thing as quite a bit of fixes have been found
for it.
Jason Baron then made dynamic debug a first class citizen module user by
using module notifier callbacks to allocate / remove module specific
dynamic debug information.
Nick Alcock has done quite a bit of work cross-tree to remove module
license tags from things which cannot possibly be module at my request
so to:
a) help him with his longer term tooling goals which require a
deterministic evaluation if a piece a symbol code could ever be
part of a module or not. But quite recently it is has been made
clear that tooling is not the only one that would benefit.
Disambiguating symbols also helps efforts such as live patching,
kprobes and BPF, but for other reasons and R&D on this area
is active with no clear solution in sight.
b) help us inch closer to the now generally accepted long term goal
of automating all the MODULE_LICENSE() tags from SPDX license tags
In so far as a) is concerned, although module license tags are a no-op
for non-modules, tools which would want create a mapping of possible
modules can only rely on the module license tag after the commit
8b41fc4454 ("kbuild: create modules.builtin without Makefile.modbuiltin
or tristate.conf"). Nick has been working on this *for years* and
AFAICT I was the only one to suggest two alternatives to this approach
for tooling. The complexity in one of my suggested approaches lies in
that we'd need a possible-obj-m and a could-be-module which would check
if the object being built is part of any kconfig build which could ever
lead to it being part of a module, and if so define a new define
-DPOSSIBLE_MODULE [0]. A more obvious yet theoretical approach I've
suggested would be to have a tristate in kconfig imply the same new
-DPOSSIBLE_MODULE as well but that means getting kconfig symbol names
mapping to modules always, and I don't think that's the case today. I am
not aware of Nick or anyone exploring either of these options. Quite
recently Josh Poimboeuf has pointed out that live patching, kprobes and
BPF would benefit from resolving some part of the disambiguation as
well but for other reasons. The function granularity KASLR (fgkaslr)
patches were mentioned but Joe Lawrence has clarified this effort has
been dropped with no clear solution in sight [1].
In the meantime removing module license tags from code which could never
be modules is welcomed for both objectives mentioned above. Some
developers have also welcomed these changes as it has helped clarify
when a module was never possible and they forgot to clean this up,
and so you'll see quite a bit of Nick's patches in other pull
requests for this merge window. I just picked up the stragglers after
rc3. LWN has good coverage on the motivation behind this work [2] and
the typical cross-tree issues he ran into along the way. The only
concrete blocker issue he ran into was that we should not remove the
MODULE_LICENSE() tags from files which have no SPDX tags yet, even if
they can never be modules. Nick ended up giving up on his efforts due
to having to do this vetting and backlash he ran into from folks who
really did *not understand* the core of the issue nor were providing
any alternative / guidance. I've gone through his changes and dropped
the patches which dropped the module license tags where an SPDX
license tag was missing, it only consisted of 11 drivers. To see
if a pull request deals with a file which lacks SPDX tags you
can just use:
./scripts/spdxcheck.py -f \
$(git diff --name-only commid-id | xargs echo)
You'll see a core module file in this pull request for the above,
but that's not related to his changes. WE just need to add the SPDX
license tag for the kernel/module/kmod.c file in the future but
it demonstrates the effectiveness of the script.
Most of Nick's changes were spread out through different trees,
and I just picked up the slack after rc3 for the last kernel was out.
Those changes have been in linux-next for over two weeks.
The cleanups, debug code I added and final fix I added for modules
were motivated by David Hildenbrand's report of boot failing on
a systems with over 400 CPUs when KASAN was enabled due to running
out of virtual memory space. Although the functional change only
consists of 3 lines in the patch "module: avoid allocation if module is
already present and ready", proving that this was the best we can
do on the modules side took quite a bit of effort and new debug code.
The initial cleanups I did on the modules side of things has been
in linux-next since around rc3 of the last kernel, the actual final
fix for and debug code however have only been in linux-next for about a
week or so but I think it is worth getting that code in for this merge
window as it does help fix / prove / evaluate the issues reported
with larger number of CPUs. Userspace is not yet fixed as it is taking
a bit of time for folks to understand the crux of the issue and find a
proper resolution. Worst come to worst, I have a kludge-of-concept [3]
of how to make kernel_read*() calls for modules unique / converge them,
but I'm currently inclined to just see if userspace can fix this
instead.
[0] https://lore.kernel.org/all/Y/kXDqW+7d71C4wz@bombadil.infradead.org/
[1] https://lkml.kernel.org/r/025f2151-ce7c-5630-9b90-98742c97ac65@redhat.com
[2] https://lwn.net/Articles/927569/
[3] https://lkml.kernel.org/r/20230414052840.1994456-3-mcgrof@kernel.org
-----BEGIN PGP SIGNATURE-----
iQJGBAABCgAwFiEENnNq2KuOejlQLZofziMdCjCSiKcFAmRG4m0SHG1jZ3JvZkBr
ZXJuZWwub3JnAAoJEM4jHQowkoinQ2oP/0xlvKwJg6Ey8fHZF0qv8VOskE80zoLF
hMazU3xfqLA+1TQvouW1YBxt3jwS3t1Ehs+NrV+nY9Yzcm0MzRX/n3fASJVe7nRr
oqWWQU+voYl5Pw1xsfdp6C8IXpBQorpYby3Vp0MAMoZyl2W2YrNo36NV488wM9KC
jD4HF5Z6xpnPSZTRR7AgW9mo7FdAtxPeKJ76Bch7lH8U6omT7n36WqTw+5B1eAYU
YTOvrjRs294oqmWE+LeebyiOOXhH/yEYx4JNQgCwPdxwnRiGJWKsk5va0hRApqF/
WW8dIqdEnjsa84lCuxnmWgbcPK8cgmlO0rT0DyneACCldNlldCW1LJ0HOwLk9pea
p3JFAsBL7TKue4Tos6I7/4rx1ufyBGGIigqw9/VX5g0Iif+3BhWnqKRfz+p9wiMa
Fl7cU6u7yC68CHu1HBSisK16cYMCPeOnTSd89upHj8JU/t74O6k/ARvjrQ9qmNUt
c5U+OY+WpNJ1nXQydhY/yIDhFdYg8SSpNuIO90r4L8/8jRQYXNG80FDd1UtvVDuy
eq0r2yZ8C0XHSlOT9QHaua/tWV/aaKtyC/c0hDRrigfUrq8UOlGujMXbUnrmrWJI
tLJLAc7ePWAAoZXGSHrt0U27l029GzLwRdKqJ6kkDANVnTeOdV+mmBg9zGh3/Mp6
agiwdHUMVN7X
=56WK
-----END PGP SIGNATURE-----
Merge tag 'modules-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
"The summary of the changes for this pull requests is:
- Song Liu's new struct module_memory replacement
- Nick Alcock's MODULE_LICENSE() removal for non-modules
- My cleanups and enhancements to reduce the areas where we vmalloc
module memory for duplicates, and the respective debug code which
proves the remaining vmalloc pressure comes from userspace.
Most of the changes have been in linux-next for quite some time except
the minor fixes I made to check if a module was already loaded prior
to allocating the final module memory with vmalloc and the respective
debug code it introduces to help clarify the issue. Although the
functional change is small it is rather safe as it can only *help*
reduce vmalloc space for duplicates and is confirmed to fix a bootup
issue with over 400 CPUs with KASAN enabled. I don't expect stable
kernels to pick up that fix as the cleanups would have also had to
have been picked up. Folks on larger CPU systems with modules will
want to just upgrade if vmalloc space has been an issue on bootup.
Given the size of this request, here's some more elaborate details:
The functional change change in this pull request is the very first
patch from Song Liu which replaces the 'struct module_layout' with a
new 'struct module_memory'. The old data structure tried to put
together all types of supported module memory types in one data
structure, the new one abstracts the differences in memory types in a
module to allow each one to provide their own set of details. This
paves the way in the future so we can deal with them in a cleaner way.
If you look at changes they also provide a nice cleanup of how we
handle these different memory areas in a module. This change has been
in linux-next since before the merge window opened for v6.3 so to
provide more than a full kernel cycle of testing. It's a good thing as
quite a bit of fixes have been found for it.
Jason Baron then made dynamic debug a first class citizen module user
by using module notifier callbacks to allocate / remove module
specific dynamic debug information.
Nick Alcock has done quite a bit of work cross-tree to remove module
license tags from things which cannot possibly be module at my request
so to:
a) help him with his longer term tooling goals which require a
deterministic evaluation if a piece a symbol code could ever be
part of a module or not. But quite recently it is has been made
clear that tooling is not the only one that would benefit.
Disambiguating symbols also helps efforts such as live patching,
kprobes and BPF, but for other reasons and R&D on this area is
active with no clear solution in sight.
b) help us inch closer to the now generally accepted long term goal
of automating all the MODULE_LICENSE() tags from SPDX license tags
In so far as a) is concerned, although module license tags are a no-op
for non-modules, tools which would want create a mapping of possible
modules can only rely on the module license tag after the commit
8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf").
Nick has been working on this *for years* and AFAICT I was the only
one to suggest two alternatives to this approach for tooling. The
complexity in one of my suggested approaches lies in that we'd need a
possible-obj-m and a could-be-module which would check if the object
being built is part of any kconfig build which could ever lead to it
being part of a module, and if so define a new define
-DPOSSIBLE_MODULE [0].
A more obvious yet theoretical approach I've suggested would be to
have a tristate in kconfig imply the same new -DPOSSIBLE_MODULE as
well but that means getting kconfig symbol names mapping to modules
always, and I don't think that's the case today. I am not aware of
Nick or anyone exploring either of these options. Quite recently Josh
Poimboeuf has pointed out that live patching, kprobes and BPF would
benefit from resolving some part of the disambiguation as well but for
other reasons. The function granularity KASLR (fgkaslr) patches were
mentioned but Joe Lawrence has clarified this effort has been dropped
with no clear solution in sight [1].
In the meantime removing module license tags from code which could
never be modules is welcomed for both objectives mentioned above. Some
developers have also welcomed these changes as it has helped clarify
when a module was never possible and they forgot to clean this up, and
so you'll see quite a bit of Nick's patches in other pull requests for
this merge window. I just picked up the stragglers after rc3. LWN has
good coverage on the motivation behind this work [2] and the typical
cross-tree issues he ran into along the way. The only concrete blocker
issue he ran into was that we should not remove the MODULE_LICENSE()
tags from files which have no SPDX tags yet, even if they can never be
modules. Nick ended up giving up on his efforts due to having to do
this vetting and backlash he ran into from folks who really did *not
understand* the core of the issue nor were providing any alternative /
guidance. I've gone through his changes and dropped the patches which
dropped the module license tags where an SPDX license tag was missing,
it only consisted of 11 drivers. To see if a pull request deals with a
file which lacks SPDX tags you can just use:
./scripts/spdxcheck.py -f \
$(git diff --name-only commid-id | xargs echo)
You'll see a core module file in this pull request for the above, but
that's not related to his changes. WE just need to add the SPDX
license tag for the kernel/module/kmod.c file in the future but it
demonstrates the effectiveness of the script.
Most of Nick's changes were spread out through different trees, and I
just picked up the slack after rc3 for the last kernel was out. Those
changes have been in linux-next for over two weeks.
The cleanups, debug code I added and final fix I added for modules
were motivated by David Hildenbrand's report of boot failing on a
systems with over 400 CPUs when KASAN was enabled due to running out
of virtual memory space. Although the functional change only consists
of 3 lines in the patch "module: avoid allocation if module is already
present and ready", proving that this was the best we can do on the
modules side took quite a bit of effort and new debug code.
The initial cleanups I did on the modules side of things has been in
linux-next since around rc3 of the last kernel, the actual final fix
for and debug code however have only been in linux-next for about a
week or so but I think it is worth getting that code in for this merge
window as it does help fix / prove / evaluate the issues reported with
larger number of CPUs. Userspace is not yet fixed as it is taking a
bit of time for folks to understand the crux of the issue and find a
proper resolution. Worst come to worst, I have a kludge-of-concept [3]
of how to make kernel_read*() calls for modules unique / converge
them, but I'm currently inclined to just see if userspace can fix this
instead"
Link: https://lore.kernel.org/all/Y/kXDqW+7d71C4wz@bombadil.infradead.org/ [0]
Link: https://lkml.kernel.org/r/025f2151-ce7c-5630-9b90-98742c97ac65@redhat.com [1]
Link: https://lwn.net/Articles/927569/ [2]
Link: https://lkml.kernel.org/r/20230414052840.1994456-3-mcgrof@kernel.org [3]
* tag 'modules-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux: (121 commits)
module: add debugging auto-load duplicate module support
module: stats: fix invalid_mod_bytes typo
module: remove use of uninitialized variable len
module: fix building stats for 32-bit targets
module: stats: include uapi/linux/module.h
module: avoid allocation if module is already present and ready
module: add debug stats to help identify memory pressure
module: extract patient module check into helper
modules/kmod: replace implementation with a semaphore
Change DEFINE_SEMAPHORE() to take a number argument
module: fix kmemleak annotations for non init ELF sections
module: Ignore L0 and rename is_arm_mapping_symbol()
module: Move is_arm_mapping_symbol() to module_symbol.h
module: Sync code of is_arm_mapping_symbol()
scripts/gdb: use mem instead of core_layout to get the module address
interconnect: remove module-related code
interconnect: remove MODULE_LICENSE in non-modules
zswap: remove MODULE_LICENSE in non-modules
zpool: remove MODULE_LICENSE in non-modules
x86/mm/dump_pagetables: remove MODULE_LICENSE in non-modules
...
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
When the SOC approaches zero, an integer overflows in the columb
counter causing the driver to react poorly. This makes the driver
think it's at (above) the fully charged capacity when in fact it's
zero. It would then write this full capacity to NVRAM which would be
used on boot if the device remained off for less than 5 hours and
not plugged in.
This can be fixed and guarded against by doing the following:
- Changing the type of tmp in rk817_read_or_set_full_charge_on_boot()
to be an int instead of a u32. That way we can account for negative
numbers.
- Guard against negative values for the full charge on boot by setting
the charge to 0 if the system charge reports less than 0.
- Catch scenarios where the battery voltage is below the design
minimum voltage and set the system SOC to 0 at that time and update
the columb counter with a charge level of 0.
- Change the off time value from 5 hours to 30 minutes before we
recalculate the current capacity based on the OCV tables.
These changes allow the driver to operate better at low voltage/low
capacity conditions.
Fixes: 3268a4d9b0 ("power: supply: rk817: Fix unsigned comparison with less than zero")
Fixes: 11cb8da018 ("power: supply: Add charger driver for Rockchip RK817")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some code was left over from debugging the driver while it was in
development. Remove this code as it's not needed.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
x86 ACPI boards which ship with only Android as their factory image may
have pretty broken ACPI tables. This includes broken _AEI ACPI GPIO event
handlers, which are normally used to listen to the micro-USB ID pin and:
1. Switch the USB-mux to the host / device USB controllers
2. Disable Vbus path before enabling the 5V boost (AXP reg 0x30 bit 7)
3. Turn 5V Vboost on / off
On non broken systems where this is not done through an ACPI GPIO event
handler, there is an ACPI INT3496 device describing the involved GPIOs
which are handled by the extcon-intel-int3496 driver; and axp288-charger.ko
listens to this extcon-device and disables the Vbus path when necessary.
On x86 Android boards, with broken ACPI GPIO event handlers, these are
disabled by acpi_quirk_skip_gpio_event_handlers() and an intel-int3496
extcon device is manually instantiated by x86-android-tablets.ko .
Add support to the axp288-charger code for this setup, so that it
properly disables the Vbus path when necessary. Note this uses
acpi_quirk_skip_gpio_event_handlers() to identify these systems,
to avoid the need to add a separate DMI match table for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This does the following code-style changes:
* fix inconsistent indentation in 'struct gab'
* remove unused cable_plugged from 'struct gab'
* remove pointless temporary is_plugged variable
* add gab_ prefix to read_channel
No functionality changes are intended.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add device context and error code to the error messages to make it
useful.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
jz4740-battery.c and s3c_adc_battery.c have been removed
from the tree and after all of my restructuring the driver
is basically no longer based on them.
Thus update the copyright information and switch to SPDX
license identifier while being at it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds full DT support to the driver. Because of the previous
changes just adding a compatible value is enough.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Another typical thing to monitor via an ADC line is
the battery temperature.
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Drop mostly useless gab_prop_to_chan() function by directly
supplying the correct enum value to read_channel().
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Constant battery data is available through power-supply's simple-battery
API. This works automatically, so the manual handling can be removed
without loosing any feature :)
Note, that the POWER_SUPPLY_STATUS_FULL check for the level variable can
be dropped, since the variable is never written. It can be re-introduced
properly once the driver gets functionality to calculate the current
charge level. Apart from that the check must be done fuzzy anyways,
since charge estimation usually is not precise enough to always return
exactly the full charge capacity for a full battery.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Drop CHARGE_NOW support, which requires a platform specific
calculation method.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Drop support for configuring IRQ jitter delay by using big
enough fixed value.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
power-supply properties are reported in µV, µA and µW.
The IIO API provides mV, mA, mW, so the values need to
be multiplied by 1000.
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Convert driver to use managed resources to simplify driver code.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Automatically expose data from the simple-battery firmware
node for all battery drivers.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to control the charging process flexible, we need to able to
disable the charger. This commit will allow to disable the charger by
"echo 1 > /sys/class/power_supply/bq256xx-charger/charge_type"
(1 = POWER_SUPPLY_CHARGE_TYPE_NONE) and enable the charger by set it to
2/3 (POWER_SUPPLY_CHARGE_TYPE_TRICKLE/POWER_SUPPLY_CHARGE_TYPE_FAST)
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Qualcomm SoC power-on driver is specific to ARCH_QCOM which depends
on OF thus the driver is OF-only. It's of_device_id table is built
unconditionally, thus of_match_ptr() for ID table does not make sense.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In da9150_charger_probe, &charger->otg_work is bound with
da9150_charger_otg_work. da9150_charger_otg_ncb may be
called to start the work.
If we remove the module which will call da9150_charger_remove
to make cleanup, there may be a unfinished work. The possible
sequence is as follows:
Fix it by canceling the work before cleanup in the da9150_charger_remove
CPU0 CPUc1
|da9150_charger_otg_work
da9150_charger_remove |
power_supply_unregister |
device_unregister |
power_supply_dev_release|
kfree(psy) |
|
| power_supply_changed(charger->usb);
| //use
Fixes: c1a281e34d ("power: Add support for DA9150 Charger")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/power/supply/bq25890_charger.c:1625:34: error: ‘bq25890_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/power/supply/bq24257_charger.c:1143:34: error: ‘bq24257_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/power/supply/ltc4162-l-charger.c:911:34: error: ‘ltc4162l_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/power/supply/lp8727_charger.c:601:34: error: ‘lp8727_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/power/supply/twl4030_charger.c:1129:34: error: ‘twl_bci_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/power/supply/rt9455_charger.c:1725:34: error: ‘rt9455_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In bq24190_probe, &bdi->input_current_limit_work is bound
with bq24190_input_current_limit_work. When external power
changed, it will call bq24190_charger_external_power_changed
to start the work.
If we remove the module which will call bq24190_remove to make
cleanup, there may be a unfinished work. The possible
sequence is as follows:
CPU0 CPUc1
|bq24190_input_current_limit_work
bq24190_remove |
power_supply_unregister |
device_unregister |
power_supply_dev_release|
kfree(psy) |
|
| power_supply_get_property_from_supplier
| //use
Fix it by finishing the work before cleanup in the bq24190_remove
Fixes: 9777467257 ("power_supply: Initialize changed_work before calling device_add")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Variable 'pirq', which may receive negative value
in platform_get_irq().
Used as an index in a function regmap_irq_get_virq().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This doesn't need to be printed every second as an error:
...
<3>[17438.628385] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17439.634176] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17440.640298] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
...
Reduce priority from ERROR to DEBUG.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The tmp is defined as u32 type, which results in invalid processing of
tmp<0 in function rk817_read_or_set_full_charge_on_boot(). Therefore,
drop the comparison.
drivers/power/supply/rk817_charger.c:828 rk817_read_or_set_full_charge_on_boot() warn: unsigned 'tmp' is never less than zero.
drivers/power/supply/rk817_charger.c:788 rk817_read_or_set_full_charge_on_boot() warn: unsigned 'tmp' is never less than zero.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3444
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- Fix DT binding for Richtek RT9467
- Fix a NULL pointer check in the power-supply core
- Document meaning of absent "present" property
-----BEGIN PGP SIGNATURE-----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=2K3C
-----END PGP SIGNATURE-----
Merge tag 'for-v6.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull more power supply updates from Sebastian Reichel:
- Fix DT binding for Richtek RT9467
- Fix a NULL pointer check in the power-supply core
- Document meaning of absent "present" property
* tag 'for-v6.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
dt-bindings: power: supply: Revise Richtek RT9467 compatible name
ABI: testing: sysfs-class-power: Document absence of "present" property
power: supply: fix null pointer check order in __power_supply_register
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> #mlxsw
Acked-by: Gregory Greenman <gregory.greenman@intel.com> #iwlwifi
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> #power_supply
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> #ahci
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The argument to do_div() is a 32-bit integer, and it was read from a
32-bit register so there is no point in doing a 64-bit division on it.
On 32-bit arm, do_div() causes a compile-time warning here:
include/asm-generic/div64.h:238:22: error: passing argument 1 of '__div64_32' from incompatible pointer type [-Werror=incompatible-pointer-types]
238 | __rem = __div64_32(&(n), __base); \
| ^~~~
| |
| unsigned int *
drivers/power/supply/qcom_battmgr.c:1130:4: note: in expansion of macro 'do_div'
1130 | do_div(battmgr->status.percent, 100);
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv
-----BEGIN PGP SIGNATURE-----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=p6Xp
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
There is an null pointer check order issue here: if we have to
check !desc and !desc->name anyway, check it before dereferencing it in
pr_warn().
Signed-off-by: qinyu <qinyu32@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Highlights:
- AMD PMC: Improvements to aid s2idle debugging
- Dell WMI-DDV: hwmon support
- INT3472 camera sensor power-management: Improve privacy LED support
- Intel VSEC: Base TPMI (Topology Aware Register and PM Capsule Interface) support
- Mellanox: SN5600 and Nvidia L1 switch support
- Microsoft Surface Support: Various cleanups + code improvements
- tools/intel-speed-select: Various improvements
- Miscellaneous other cleanups / fixes
The following is an automated git shortlog grouped by driver:
Add include/linux/platform_data/x86 to MAINTAINERS:
- Add include/linux/platform_data/x86 to MAINTAINERS
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix header inclusion in linux/platform_data/x86/soc.h:
- Fix header inclusion in linux/platform_data/x86/soc.h
HID:
- surface-hid: Use target-ID enum instead of hard-coding values
MAINTAINERS:
- dell-wmi-sysman: drop Divya Bharathi
- Add entry for TPMI driver
Merge tag 'ib-leds-led_get-v6.3' into HEAD:
- Merge tag 'ib-leds-led_get-v6.3' into HEAD
acerhdf:
- Drop empty platform remove function
apple_gmux:
- Drop no longer used ACPI_VIDEO Kconfig dependency
dell-ddv:
- Prefer asynchronous probing
- Add hwmon support
- Add "force" module param
- Replace EIO with ENOMSG
- Return error if buffer is empty
- Add support for interface version 3
dell-smo8800:
- Use min_t() for comparison and assignment
dell-wmi-sysman:
- Make kobj_type structure constant
hp-wmi:
- Ignore Win-Lock key events
int1092:
- Switch to use acpi_evaluate_dsm_typed()
int3472/discrete:
- add LEDS_CLASS dependency
- Drop unnecessary obj->type == string check
- Get the polarity from the _DSM entry
- Move GPIO request to skl_int3472_register_clock()
- Create a LED class device for the privacy LED
- Refactor GPIO to sensor mapping
intel:
- punit_ipc: Drop empty platform remove function
- oaktrail: Drop empty platform remove function
intel/pmc:
- Switch to use acpi_evaluate_dsm_typed()
leds:
- led-class: Add generic [devm_]led_get()
- led-class: Add __devm_led_get() helper
- led-class: Add led_module_get() helper
- led-class: Add missing put_device() to led_put()
media:
- v4l2-core: Make the v4l2-core code enable/disable the privacy LED if present
nvidia-wmi-ec-backlight:
- Add force module parameter
platform:
- mellanox: mlx-platform: Move bus shift assignment out of the loop
- mellanox: mlx-platform: Add mux selection register to regmap
- mellanox: Extend all systems with I2C notification callback
- mellanox: Split logic in init and exit flow
- mellanox: Split initialization procedure
- mellanox: Introduce support of new Nvidia L1 switch
- mellanox: Introduce support for next-generation 800GB/s switch
- mellanox: Cosmetic changes - rename to more common name
- mellanox: Change "reset_pwr_converter_fail" attribute
- mellanox: Introduce support for rack manager switch
platform/mellanox:
- mlxreg-hotplug: Allow more flexible hotplug events configuration
platform/surface:
- Switch to use acpi_evaluate_dsm_typed()
- aggregator: Rename top-level request functions to avoid ambiguities
- aggregator_registry: Fix target-ID of base-hub
- aggregator: Enforce use of target-ID enum in device ID macros
- dtx: Use target-ID enum instead of hard-coding values
- aggregator_tabletsw: Use target-ID enum instead of hard-coding values
- aggregator_hub: Use target-ID enum instead of hard-coding values
- aggregator: Add target and source IDs to command trace events
- aggregator: Improve documentation and handling of message target and source IDs
platform/x86/amd:
- pmc: Add line break for readability
- pmc: differentiate STB/SMU messaging prints
- pmc: Write dummy postcode into the STB DRAM
- pmc: Add num_samples message id support to STB
platform/x86/amd/pmf:
- Add depends on CONFIG_POWER_SUPPLY
platform/x86/intel:
- Intel TPMI enumeration driver
platform/x86/intel/tpmi:
- ADD tpmi external interface for tpmi feature drivers
- Process CPU package mapping
platform/x86/intel/vsec:
- Use mutex for ida_alloc() and ida_free()
- Support private data
- Enhance and Export intel_vsec_add_aux()
- Add TPMI ID
platform_data/mlxreg:
- Add field with mapped resource address
think-lmi:
- Make kobj_type structure constant
- Use min_t() for comparison and assignment
tools/power/x86/intel-speed-select:
- v1.14 release
- Adjust uncore max/min frequency
- Add Emerald Rapid quirk
- Fix display of uncore min frequency
- turbo-freq auto mode with SMT off
- cpufreq reads on offline CPUs
- Use null-terminated string
- Remove duplicate dup()
- Handle open() failure case
- Remove unused non_block flag
- Remove wrong check in set_isst_id()
x86/platform/uv:
- Make kobj_type structure constant
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmPzRpgUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9wYPwf+I6PP0XBg8MrivLc2DHklVojUU0aX
/M0LbCP8gxCDdyisV8swC3e848riaTchYlUGASPZu0ieas1U7KsDvghkiittNvlI
U+0h7TbkOQNymM8oE0oauflH4W5KwCXGrLsJWVkGk0lhJd6WmjXkjWLkruaXazLd
kc5fq0QyzRVzhhCtocQ7qhIgXSZyKYx433VqbDR7/SUi5F2wkC9JbGY02maKWaK3
4lQaoyMKLjGlDr9YVv+UHTwLoXwP0mW/fjlsZ3Xz5lz6WfihQzPuOrl/10mRj0Ez
eP9dlF1Dipee4BYS2FM5dtk5xPpqdVqRlQUX2qKzyDNTSx5wdtJnv8j/cg==
=VoXq
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- AMD PMC: Improvements to aid s2idle debugging
- Dell WMI-DDV: hwmon support
- INT3472 camera sensor power-management: Improve privacy LED support
- Intel VSEC: Base TPMI (Topology Aware Register and PM Capsule
Interface) support
- Mellanox: SN5600 and Nvidia L1 switch support
- Microsoft Surface Support: Various cleanups + code improvements
- tools/intel-speed-select: Various improvements
- Miscellaneous other cleanups / fixes
* tag 'platform-drivers-x86-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (80 commits)
platform/x86: nvidia-wmi-ec-backlight: Add force module parameter
platform/x86/amd/pmf: Add depends on CONFIG_POWER_SUPPLY
platform/x86: dell-ddv: Prefer asynchronous probing
platform/x86: dell-ddv: Add hwmon support
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform: mellanox: mlx-platform: Move bus shift assignment out of the loop
platform: mellanox: mlx-platform: Add mux selection register to regmap
platform_data/mlxreg: Add field with mapped resource address
platform/mellanox: mlxreg-hotplug: Allow more flexible hotplug events configuration
platform: mellanox: Extend all systems with I2C notification callback
platform: mellanox: Split logic in init and exit flow
platform: mellanox: Split initialization procedure
platform: mellanox: Introduce support of new Nvidia L1 switch
platform: mellanox: Introduce support for next-generation 800GB/s switch
platform: mellanox: Cosmetic changes - rename to more common name
platform: mellanox: Change "reset_pwr_converter_fail" attribute
platform: mellanox: Introduce support for rack manager switch
MAINTAINERS: dell-wmi-sysman: drop Divya Bharathi
x86/platform/uv: Make kobj_type structure constant
platform/x86: think-lmi: Make kobj_type structure constant
...
Since this driver can only be built-in, it fails to link when
the I2C layer is in a loadable module:
x86_64-linux-ld: drivers/power/reset/odroid-go-ultra-poweroff.o: in function `odroid_go_ultra_poweroff_get_pmic_device':
odroid-go-ultra-poweroff.c:(.text+0x30): undefined reference to `i2c_find_device_by_fwnode'
Tighten the dependency to only allow enabling
POWER_RESET_ODROID_GO_ULTRA_POWEROFF is I2C is built-in as well.
Fixes: cec3b46b8b ("power: reset: add Odroid Go Ultra poweroff driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of relying on an accidental, transitive inclusion of linux/leds.h
use it directly.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Hardkernel Odroid Go Ultra poweroff scheme requires requesting a poweroff
to its two PMICs in order, this represents the poweroff scheme needed to complete
a clean poweroff of the system.
This implement this scheme by implementing a self registering driver to permit
using probe defer until both pmics are finally probed.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The PMIC GLINK service, running on a coprocessor of modern Qualcomm
platforms, deals with battery charging and fuel gauging, as well as
reporting status of AC and wireless power supplies.
As this is just one of the functionalities provided by the PMIC GLINK
service, this power supply driver is implemented as an auxilirary bus
driver, spawned by the main "pmic glink" driver when the PMIC GLINK
service is detected.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM8350 PDX215
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-MTP & SM8450-HDK
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230207144241.1767973-1-quic_bjorande@quicinc.com
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pass the correct 'ce_gpio' to IS_ERR(), and remove the ce_gpio in
chip data, make it all by SW control only, not to control by HW pin.
Fixes: 4a1a5f6781 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The return value of max77650_charger_disable() is ignored by all but one
caller. That one caller propagates the error code in the platform driver's
remove function. The only effect of that is that the driver core emits
a generic error message (but still removes the device). As
max77650_charger_disable() already emits an error message, this can better
be changed to return zero.
This is a preparation for making struct platform_driver::remove return
void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
RT9467 is a switch-mode single cell Li-Ion/Li-Polymer battery charger
for portable applications.
It integrates a synchronous PWM controller, power MOSFETs,
input current sensing and regulation, high-accuracy voltage regulation,
and charge termination. The charge current is regulated through
integrated sensing resistors.
The RT9467 also features USB On-The-Go (OTG) support. It also integrates
D+/D- pin for USB host/charging port detection.
Co-developed-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the RT9471 3A 1-Cell Li+ battery charger.
The RT9471 is a highly-integrated 3A switch mode battery charger with
low impedance power path to better optimize the charging efficiency.
Co-developed-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL-terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The EDV1/SOC1 flag is set when the battery voltage drops below the
threshold set in EEPROM. From observing the capacity_level reported by
the driver, and reading the datasheet, EDV1 remains set even when
EDVF/SOCF gets set. Thus, bq27xxx_battery_capacity_level() never reaches
the CAPACITY_LEVEL_CRITICAL code path, since CAPACITY_LEVEL_LOW takes
precedence.
This commit fixes the issue by swapping the order in which the flags are
tested. It was tested with bq27200 in the Nokia N900.
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Init the ichg/vbat reg with chip default value instead of the max value
used now. The max value set in driver will result an unsafe case (e.g.
battery is over charging when in a hot environment) if no user space
update the value later.
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Finish the job started by the commit ba940ed832 ("power: supply:
collie_battery: Convert to GPIO descriptors"), i.e. convert the use
of gpio_to_irq() to gpiod_to_irq(). No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The rn5t618 power driver fails to register
a cooling device because POWER_SUPPLY_PROP_CHARGE_CONTROL_LIMIT_MAX
is missing but availability is not checked before registering
cooling device. After improved error checking in the thermal
code, the registration of the power supply fails entirely.
Checking for availability of _MAX before registering cooling device
fixes the rn5t618 problem. But the whole logic feels questionable.
First, the logic is inverted here:
the code tells: max_current = max_cooling but
0 = max_cooling, so there needs to be some inversion
in the code which cannot be found. Comparing with other
cooling devices, it can be found that value for fan speed is not
inverted, value for cpufreq cooling is inverted (similar situation
as here lowest frequency = max cooling)
Second, analyzing usage of _MAX: it is seems that maximum capabilities
of charging controller are specified and not of the battery. Probably
there is not too much mismatch in the drivers actually implementing
that. So nothing has exploded yet. So there is no easy and safe way
to specifify a max cooling value now.
Conclusion for now (as a regression fix) just remove the cooling device
registration and do it properly later on.
Fixes: e49a1e1ee0 ("thermal/core: fix error code in __thermal_cooling_device_register()")
Fixes: 952aeeb3ee ("power_supply: Register power supply for thermal cooling device")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Read new optional device tree property priority for specifying priority
level of reset handler. Default value is 192 as before.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Similar to the target category (TC), the target ID (TID) can be one
value out of a small number of choices, given in enum ssam_ssh_tid.
In the device ID macros, SSAM_SDEV() and SSAM_VDEV() we already use text
expansion to, both, remove some textual clutter for the target category
values and enforce that the value belongs to the known set. Now that we
know the names for the target IDs, use the same trick for them as well.
Also rename the SSAM_ANY_x macros to SSAM_SSH_x_ANY to better fit in.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221202223327.690880-9-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver was used for a couple of Intel PXA and Samsung S3C24xx
based PDAs, but all of those are now removed from the kernel, so
the driver itself is no longer useful.
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: linux-pm@vger.kernel.org
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some devices, such as the Lenovo Yoga Tab 3 Pro (YT3-X90F) have
multiple batteries with a separate bq25890 charger for each battery.
This requires the maximum current the external power-supply can deliver
to be divided over the chargers. The Android vendor kernel shipped
on the YT3-X90F divides this current with a 40/60 percent split so that
batteries are done charging at approx. the same time if both were fully
empty at the start.
Add support for a new "linux,iinlim-percentage" percentage property which
can be set to indicate that a bq25890 charger should only use that
percentage of the external power-supply's maximum current.
So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some devices, such as the Lenovo Yoga Tab 3 Pro (YT3-X90F) have multiple
batteries with a separate bq25890 charger for each battery.
This requires some coordination between the chargers specifically
the main charger needs to put the secondary charger in Hi-Z mode when:
1. Enabling its 5V boost (OTG) output to power an external USB device,
to avoid the secondary charger IC seeing this as external Vbus and
then trying to charge the secondary battery from this.
2. Talking the Pump Express protocol to increase the external Vbus voltage.
Having the secondary charger drawing current when the main charger is
trying to talk the Pump Express protocol results in the external Vbus
voltage not being raised.
Add a new "linux,secondary-charger-name" string device-property, which
can be set to the power_supply class device's name of the secondary
charger when there is a secondary charger; and make the Vbus regulator and
Pump Express code put the secondary charger in Hi-Z mode when necessary.
So far this new property is only used on x86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added
to the existing devicetree-bindings.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The PXA tosa machine is removed, so this driver is no longer
in use.
Cc: linux-pm@vger.kernel.org
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PXA z2 platform is gone, and this driver is now orphaned.
Cc: linux-pm@vger.kernel.org
Cc: Peter Edwards <sweetlilmre@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The majority of all pxa board files has not been touched in a long time,
and no users have spoken up in favor of keeping them around. This leaves
only support for the platforms that were already converted to DT, as
well as the gumstix and spitz/akita/borzoi machines that work in qemu
and can still be converted to DT later.
Cc: Ales Bardorfer <ales@i-tech.si>
Cc: Ales Snuparek <snuparek@atlas.cz>
Cc: Alex Osborne <ato@meshy.org>
Cc: Alex Osborne <bobofdoom@gmail.com>
Cc: Dirk Opfer <dirk@opfer-online.de>
Cc: Ian Molton <spyro@f2s.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Petchkovsky <mkpetch@internode.on.net>
Cc: Nick Bane <nick@cecomputing.co.uk>
Cc: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Tomas Cech <sleep_walker@suse.cz>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The s3c-adc driver is removed along with the s3c24xx platform,
so the battery driver is no longer needed either.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some devices, such as the Lenovo Yoga Tab 3 Pro (YT3-X90F) have
multiple batteries with a separate bq25890 charger for each battery.
This requires the bq25890_charger code to use a unique name per
registered power_supply class device, rather then hardcoding
"bq25890-charger" as power_supply class device name.
Add a "-%d" prefix to the name, allocated through idr in the same way
as several other power_supply drivers are already doing this.
Note this also updates: drivers/platform/x86/x86-android-tablets.c
which refers to the charger by power_supply-class-device-name for
the purpose of setting the "supplied-from" property on the fuel-gauge
to this name.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code to check if F_CONV_RATE has been set, or if a manual ADC
conversion needs to be triggered, as well as the code to set
the initial F_CONV_RATE value at probe both where not taking
HiZ mode into account. Add checks for this.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The recent "power: supply: bq25890: Add HiZ mode support" change
leaves F_CONV_RATE rate unset when disabling HiZ mode (setting
POWER_SUPPLY_PROP_ONLINE to 1) while a charger is connected.
Separate the resetting HiZ mode (when necessary because of a charger
(re)plug event) into its own "if {}" block which runs first.
And fix the setting of F_CONV_RATE rate by adding helper variables for
the old and new F_CONV_RATE state which check both the online and hiz bits
and then compare the helper variables to see if a F_CONV_RATE update is
necessary.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25890 is capable of disconnecting itself from the external supply,
in which case the system is supplied only from the battery. This can be
useful e.g. to test the pure battery operation, or draw no power from
USB port.
Implement support for this mode, which can be toggled by writing 0 or
non-zero to sysfs 'online' attribute, to select either offline or online
mode.
The IRQ handler has to be triggered to update chip state, as switching
to and from HiZ mode does not generate an interrupt automatically.
The IRQ handler reinstates the HiZ mode in case a cable is replugged by
the user, the chip itself clears the HiZ mode bit when cable is plugged
in by the user and the chip detects PG bad-to-good transition.
Signed-off-by: Marek Vasut <marex@denx.de>
[hdegoede@redhat.com: Replace "&" with "&&" in a boolean check]
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull the chip state and ADC conversion update functionality out into
separate function, so it can be reused elsewhere in the driver. This
is a preparatory patch, no functional change.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
A call to platform_get_irq_byname() already prints an error on failure
within its own implementation. So printing another error based on its
return value in the caller is redundant and should be removed. The
clean up also makes if condition block braces and the device pointer
variable dev unnecessary. Remove those as well.
Issue identified using platform_get_irq.cocci coccinelle semantic patch.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As documented in Documentation/filesystems/sysfs.rst the sysfs show()
function should use sysfs_emit() or sysfs_emit_at() to format the
userspace return value. This replaces all sysfs related instances of
sprintf() with sysfs_emit() in the power-supply subsystem.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
[Drop sysfs_emit changes done for code not related to sysfs show
and reword commit message]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As documented in Documentation/filesystems/sysfs.rst the sysfs
show() function should use sysfs_emit() or sysfs_emit_at() to
format the userspace return value. This replaces all instances
of scnprintf() with sysfs_emit() in the power-supply subsystem.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
[reword commit message]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- bq25890: add charge voltage/current support
- bd99954: convert to linear range
- convert all i2c drivers to use probe_new
- misc. fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=xxhs
-----END PGP SIGNATURE-----
Merge tag 'for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- bq25890: add charge voltage/current support
- bd99954: convert to linear range
- convert all i2c drivers to use probe_new
- misc fixes and cleanups
* tag 'for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (51 commits)
power: supply: fix null pointer dereferencing in power_supply_get_battery_info
power: supply: bq25890: Fix usb-notifier probe and remove races
power: supply: bq25890: Ensure pump_express_work is cancelled on remove
power: supply: Fix refcount leak in rk817_charger_probe
power: supply: bq25890: Only use pdata->regulator_init_data for vbus
power: supply: ab8500: Fix error handling in ab8500_charger_init()
power: supply: cw2015: Fix potential null-ptr-deref in cw_bat_probe()
power: supply: z2_battery: Fix possible memleak in z2_batt_probe()
power: supply: z2_battery: Convert to i2c's .probe_new()
power: supply: ucs1002: Convert to i2c's .probe_new()
power: supply: smb347: Convert to i2c's .probe_new()
power: supply: sbs-manager: Convert to i2c's .probe_new()
power: supply: sbs: Convert to i2c's .probe_new()
power: supply: rt9455: Convert to i2c's .probe_new()
power: supply: rt5033_battery: Convert to i2c's .probe_new()
power: supply: max17042_battery: Convert to i2c's .probe_new()
power: supply: max17040: Convert to i2c's .probe_new()
power: supply: max14656: Convert to i2c's .probe_new()
power: supply: ltc4162-l: Convert to i2c's .probe_new()
power: supply: ltc2941: Convert to i2c's .probe_new()
...
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
when kmalloc() fail to allocate memory in kasprintf(), propname
will be NULL, strcmp() called by of_get_property() will cause
null pointer dereference.
So return ENOMEM if kasprintf() return NULL pointer.
Fixes: 3afb50d712 ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are 2 races surrounding the usb-notifier:
1. The notifier, and thus usb_work, may run before the bq->charger
power_supply class device is registered. But usb_work may call
power_supply_changed() which relies on the psy device being registered.
2. usb_work may be pending/running at remove() time, so it needs to be
cancelled on remove after unregistering the usb-notifier.
Fix 1. by moving usb-notifier registration to after the power_supply
registration.
Fix 2. by adding a cancel_work_sync() call directly after the usb-notifier
unregistration.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
