Connect twl4030 voice DAI to McBSP3 in sdp3430 machine driver.
Voice DAI init function enables corresponding interface by
writting directly to VOICE_IF codec register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a control for selecting the codec operation mode. TWL4030 codec
has two modes:
- Option 1. Audio only (4 audio DACs)
- Option 2. Voice/Audio (2 audio DACs and voice ADC/DAC)
Control is restricted when a stream is ongoing, since codec's
operation mode cannot be changed on-the-fly.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AUXR is selected by bit 2 and not by bit 1 in the ANAMICR register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than managing the bias level of the system based on if there is
an active audio stream manage it based on there being an active DAPM
widget. This simplifies the code a little, moving the power handling
into one place, and improves audio performance for bypass paths when no
playbacks or captures are active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM has always applied any changes to the power state of widgets as soon
as it has determined that they are required. Instead of doing this store
all the changes that are required on lists of widgets to power up and
down, then iterate over those lists and apply the changes. This changes
the sequence in which changes are implemented, doing all power downs
before power ups and always using the up/down sequences (previously they
were only used when changes were due to DAC/ADC power events). The error
handling is also changed so that we continue attempting to power widgets
if some changes fail.
The main benefit of this is to allow future changes to do optimisations
over the whole power sequence and to reduce the number of walks of the
widget graph required to check the power status of widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable TWL4030 VTXL/VTXR and VRX digital filters for uplink
and downlink paths, respectively.
This patch also corrects voice 8/16kHz mode selection bit
(SEL_16K) of CODEC_MODE register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Eliminate direct accesses to the driver_data field.
cf 82ab13b26f15f49be45f15ccc96bfa0b81dfd015
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device *dev;
expression E;
type T;
@@
- dev->driver_data = (T)E
+ dev_set_drvdata(dev, E)
@@
struct device *dev;
type T;
@@
- (T)dev->driver_data
+ dev_get_drvdata(dev)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use default to optimize the switch/case in magicial_playback_hw_params(),
which also fixes the compile warnings below:
sound/soc/pxa/magician.c:89: warning: 'acds' may be used uninitialized in this function
sound/soc/pxa/magician.c:89: warning: 'acps' may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a build fix, resyncing the DaVinci EVM ASoC board code
with the version in the DaVinci tree. That resync includes
support for the DM355 EVM, although that board isn't yet in
mainline.
(NOTE: also includes a bugfix to the platform_add_resources
call, recently sent by Chaithrika U S <chaithrika@ti.com> but
not yet merged into the DaVinci tree.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This resyncs the DaVinci I2S code with the version in the DaVinci
tree. The behavioral change uses updated clock interfaces which
recently merged to mainline. Two other changes include adding a
comment on the ASP/McBSP/McASP confusion, and dropping pdev->id in
order to support more boards than just the DM644x EVM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a buildfix for the DaVinci PCM code, resyncing it with
the version in the DaVinci tree. The notable change is using
current EDMA interfaces, which recently merged to mainline.
(The older interfaces never made it into mainline.)
NOTE: open issue, the DMA should be to/from SRAM; see chip
errata for more info. The artifacts are extremely easy to
hear on DM355 hardware (not yet supported in mainline), but
don't seem as audible on DM6446 hardwaare (which does have
mainline support).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9712 can be configured by resistor strapping GPIO4 to behave like
the WM9713 and default to leaving the AC97 link disabled after cold
reset until a warm reset occurs. In this configuration we need to issue
a warm reset after cold to bring the link up so do so. The warm reset
will be harmless on systems that don't need it.
[Changelog rewritten to document the reasoning. -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pxa2xx_i2s_resume is :
- unconditionnaly setting SACR0_ENB
- unsetting SACR0_ENB in saved SACR0 pxa_i2s.sacr0
fix these.
In pxa2xx_i2s_{resume,suspend}, save/restore registers even
when !dai->active.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
i2s_clk is 'put' for no reason in pxa2xx_i2s_shutdown.
Now we 'get' i2s_clk at probe and 'put' it at driver removal or when
probe fails.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- hw_params enables both RPL and REC functions each time : Enable the
appropriate function in pxa2xx_i2s_trigger.
- pxa2xx_i2s_shutdown disables i2s anytime one of RPL or REC function is
off : Turn it off only when both functions are off.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we are in a know good state at end of probe :
Reset FIFO logic and registers, and make sure REC and RPL functions
along with FIFO service are disabled (SACR0_RST enables REC and RPL).
Resetting loses current settings so remove reset from stream startup.
Now reset occurs only at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Resending the patch after fixing the minor issues.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reset FIFO logic and registers, and make sure REC and RPL functions along
with FIFO service are disabled at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The inputs of the twl4030 codec can be mixed, so we will use the mixer
DAPM for the analog microphone registers(0x05, 0x06), but if we enable
more than one input at the same time, the input impedance of the input
amplifier will be reduced.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the card was not instantiated in snd_soc_instantiate_card, calling
soc-remove will crash because some of codec, cpu_dai and card .remove
methods are called twice.
Fix this by returning from soc_remove immediately.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC uses the standard ALSA data format definitions to specify the wire
format used between the CPU and CODEC. Since the ALSA data formats all
include the endianess of the data but this information is not relevant
by the time the data has been encoded onto the serial link to the CODEC
this means that either all the CODEC drivers need to declare both big and
little endian variants or the core needs to fix up the format constraints
specified by CODEC drivers.
For now take the latter approach - this will need to be revisited if any
CODECs are endianness dependant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC driver for AT91SAM9260-based AFEB9260 board
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Copy-paste error: TWL4030_PRECKL_GAIN >> TWL4030_PRECKR_GAIN
It has not caused problems, since
TWL4030_PRECKL_GAIN == TWL4030_PRECKR_GAIN == 0x30
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the magic 0x80 value with a suitable macro definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the VIBRA output on TWL4030 codec.
The VIBRA output can be driven with audio data or with
local vibrator driver.
Add the needed DAPM elements and routes for the VIBRA output and
controls for the VIBRA driver configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the ASoC side of the board support for the Crossbow
IMB400 daughter board.
Thanks to Crossbow for considerable assistance.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add voice digital loopback (sidetone) to the twl4030
driver. It mixes voice uplink attenuated (by sidetone gain) with
voice downlink when the codec is working in option2 (voice/audio
mode).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voice downlink analog bypass switch. It follows
the same approach as in other analog bypass switches.
DAC switch is moved from 'DAC Voice' to 'Analog Voice Playback Mixer',
that will also allow voice DAC to be powered in digital voice
loopback (sidetone).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mis-typing exist in dapm controller definitions and dapm route definitions,
so happen mis-matched error when snd_soc_dapm_add_routes().
Cc: stable@kernel.org
Signed-off-by: Jinyoung Park <parkjy@mtekvision.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com
The AC97 wire format is completely fixed so CODECs don't have any choice
about the formats they accept but controllers accept a variety of data
formats and render them down onto the bus. Have a shared define so all
the CODEC drivers will interoperate with any of our controller drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't used by anything external and aren't prototyped; if any
users appear they can be exported again for them.
Also report what modes we have a problem with when we encounter invalid
mode configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
