To quote from section 1.3.1 of the data sheet:
The SGTL5000 has an internal reset that is deasserted
8 SYS_MCLK cycles after all power rails have been brought
up. After this time, communication can start
...
1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When SCC work in DSP A mode, the data outputs/inputs are shift out on
falling edge, the frame sync are sample on the rising edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue introduced by:
3684940933 ASoC: tlv320aic3x: Add TDM support
The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.
Fixes: 3684940933 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We need hold lock each time updating shirm registers, otherwise,
we may set unexpected values to them when they are set in
different thread at different time sequence.
The notification work will be scheduled in global work queue,
which won't hold this sst->spinlock itself, so here we need
change to use the lock version to update shim registers.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the I2S specification information as following:
- WS = 0, channel 1 (left)
- WS = 1, channel 2 (right)
So, the start event should be TF/RF falling edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the last subscriber to a "Through" port has been removed, the
subscribed destination ports might still be active, so it would be
wrong to send "all sounds off" and "reset controller" events to them.
The proper place for such a shutdown would be the closing of the actual
MIDI port (and close_substream() in rawmidi.c already can do this).
This also fixes a deadlock when dummy_unuse() tries to send events to
its own port that is already locked because it is being freed.
Reported-by: Peter Billam <peter@www.pjb.com.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do no send MIDI bytes at the full rate at which FireWire packets happen
to be sent, but restrict them to the actual rate of a real MIDI port.
This is required by the specification, and prevents data loss when the
device's buffer overruns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several devices that expect to receive MIDI data only in the
first eight data blocks of a packet. If the driver restricts the data
rate to the allowed rate (as mandated by the specification, but not yet
implemented by this driver), this happens naturally. Therefore, there
is no reason to ever try to use more data packets with any device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We should select FSR also to be driven by McBSP, not only FSX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In soc_new_compress() when rtd->dai_link->dynamic is set, we create the pcm
substreams with this call:
ret = snd_pcm_new_internal(rtd->card->snd_card, new_name, num,
1, 0, &be_pcm);
which passes 0 as capture_count leading to
be_pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream
being NULL, hence when trying to set rtd a few lines below we get an oops.
Fix by using rtd->dai_link->dpcm_playback and rtd->dai_link->dpcm_capture as
playback_count and capture_count to snd_pcm_new_internal().
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There is only one I2S I/F, AD/DA path must operate to the same
format.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the path name for mux to get rid of the following warning:
--->8---
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTR
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTR
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACL
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACL
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACR
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACR
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If asoc_simple_card_probe() fails, asoc_simple_card_unref() may be
called before dev_set_drvdata(), causing a NULL pointer dereference in
asoc_simple_card_unref():
Unable to handle kernel NULL pointer dereference at virtual address 000000d4
...
PC is at asoc_simple_card_unref+0x14/0x48
LR is at asoc_simple_card_probe+0x3d4/0x40c
This typically happens because asoc_simple_card_parse_of() returns
-EPROBE_DEFER, but other failure modes are possible.
devm_snd_soc_register_card()/snd_soc_register_card() may fail either
before or after dev_set_drvdata().
Pass a snd_soc_card pointer instead of a platform_device pointer to
asoc_simple_card_unref() to fix this.
Note that if CONFIG_OF_DYNAMIC=n, of_node_put() is a dummy, and gcc may
optimize away the loop over card->dai_link, never actually dereferencing
card, and thus avoiding the crash...
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: e512e001da ("ASoC: simple-card: Fix the reference count of device nodes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The following crash happens when trying to unload the snd_soc_imx_wm8962 module
while playback is active:
[ 208.666868] Unable to handle kernel paging request at virtc
[ 208.674110] pgd = 80004000
[ 208.676867] [7f06541c] *pgd=4c334811, *pte=00000000, *ppte=00000000
[ 208.683211] Internal error: Oops: 80000007 [#1] SMP ARM
[ 208.688445] Modules linked in: snd_soc_wm8962 snd_soc_fsl_ssi snd_soc_imx_audmux imx_pcm_fiq evbug]
...
In order to avoid such problem, fill the card owner field as suggested by
Lars-Peter Clausen:
"But looking at the source it seems that this is a core feature of ALSA and at
least for the card module itself it will do the ref-counting when a stream is
started/stopped. And we even support setting the owner of a card in ASoC.
It's just that pretty much no ASoC card driver bothers to set the owner field
in the snd_soc_card struct. So this particular problem can be fixed by updating
the imx-wm8962 driver to set the owner field."
By doing as suggested, we no longer see the crash when attempting to unload the
snd_soc_imx_wm8962 module while playback is active:
$ modprobe -r snd_soc_imx_wm8962
modprobe: can't unload module snd_soc_imx_wm8962: Resource temporarily
unavailable
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP programs are listed out of order.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The patch modified the behavior that updates the PLL parameter. It set the
update bit before the PLL power up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2ffa531078 ("ASoC: fsl_ssi: Fix module unbound") changed the way to
retrieve the irq number from irq_of_parse_and_map() to platform_get_irq(), but
missed to updated the irq error check accordingly.
We should test for negative irq number and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not send IPC stream commands to FW when the stream is
NULL, dereference the NULL pointer may also occur without precheck.
Here add NULL pointer checks for these stream APIs.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the 't->length' is a big-endian value, it's used without any
conversion. This means that the driver always uses 'length' parameter.
Fixes: 555e8a8f7f14("ALSA: fireworks: Add command/response functionality into hwdep interface")
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0072 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The probe routine was disabling the clock even
if the system was configured successfully. Add
a return statement to leave clocks enabled.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset of block allocator, ba->offset, should not be changed during
fixed address allocating, for the caller may treat it as the offset of
allocated memory and use it. In the case that we allocate more than 1
blocks, we should make sure this offset is correct.
Here introduces a temp allocator for the later continuous allocating.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ts3a227e does not trigger interrupt to report jack status when system
boots from warm reset because ts3a227e's power remains on during warm reset.
Read jack status at probe to get current jack status.
Note that if system boots from EC reset, then this issue will not
happen.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
stac_store_hints() does utterly wrong for masking the values for
gpio_dir and gpio_data, likely due to copy&paste errors. Fortunately,
this feature is used very rarely, so the impact must be really small.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 897c329bc ("ALSA: usb: caiaq: check for cdev->n_streams > 1")
introduced a safety check to protect against bogus data provided by
devices. However, the n_streams variable is already divided by
CHANNELS_PER_STREAM, so the correct check is 'n_streams > 0'.
Fix this to un-break support for stereo devices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: stable@kernel.org [v3.18+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few fixes for v3.19, a few driver specifics and one core fix which
fixes a boot crash on OMAP if deferred probing kicks in due to
attempting to modify static data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoXnhAAoJECTWi3JdVIfQU98H+wYL3/11DUS+qOhjkHBUzStB
VIIuw4Zf1gfEG+0gPSVI/oE0nTVZyYGGV2qIn01SDPMjOdcCRpC5sdwHDEN/YNXR
v9zpWydtUILkram4xXsUiqyJTznPOeqM7HUVROZu3IkR3IcFZ8eCjoXghZXcNuWo
6RezroZkV3KhUrxSWl0D07cWfl76dJt4XSKrT9a1iFGFg1fMBK9PwquhNbD1vami
n2kR740u95wDPIbxRliBm6yYuJ6D2Fwi5BmCGfp4gml+685tXMBmDZ26+W3nKQdZ
TiZyhMbtcGN3rYEoaKwHEeTCgfQtMxgxoyhcniOIZvbiV9oT3jtTJAl38xnnS5E=
=pFlY
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.19
A few fixes for v3.19, a few driver specifics and one core fix which
fixes a boot crash on OMAP if deferred probing kicks in due to
attempting to modify static data.
The xDC field should have 5 bit width according to Reference Manual.
Thus this patch fixes it.
Signed-off-by: Aurelien BOUIN <a_bouin@yahoo.fr>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The total stream number of Skylake's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implemented separate stream_tag assignment for input and output streams.
According to hda specification stream tag must be unique throughout the
input streams group, however an output stream might use a stream tag
which is already in use by an input stream. This change is necessary
to support HW which provides a total of more than 15 stream DMA engines
which with legacy implementation causes an overflow on SDxCTL.STRM
field (and the whole SDxCTL register) and as a result usage of
Reserved value 0 in the SDxCTL.STRM field which confuses HDA controller.
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since RK3288 DMAC's burst length only support max to 4, here
set maxburst of playback and capture dma data to 4.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to description about "Transmit Data Level",
This bit field controls the level at which a DMA request
is made by the transmit logic.
It is equal to the watermark level.
That is, the dma_tx_req signal is generated when the number
of valid data entries in the TXFIFO
(TXFIFO0 if CSR=00
TXFIFO1 if CSR=01
TXFIFO2 if CSR=10
TXFIFO3 if CSR=11)
is equal to or below this field value.
Different to receive data level, transmit data level does not need
to "-1".
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For block span more than 1 section, when allocate it from
a free block, we need allocate the remain buffers within
the block, and then continue alloc the rest of needed
size buffer.
Here also make sure this free block is moved from free
list to used list, and add it to block_list which may
be used for power gating disabling later.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_kcontrol_chip should return snd_soc_component instead of
snd_soc_codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_sst_bytcr_dpcm_rt5640 doesn't autoload because MODULE_ALIAS doesn't
match with "bytt100_rt5640" platform device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
