The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
smatch warnings:
drivers/crypto/stm32/stm32-crc32.c:108 stm32_crc_get_next_crc() warn:
can 'crc' even be NULL?
Use list_first_entry_or_null instead of list_first_entry to retrieve
the first device registered.
The function list_first_entry always return a non NULL pointer even if
the list is empty. Hence checking if the pointer returned is NULL does
not tell if the list is empty or not.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202311281111.ou2oUL2i-lkp@intel.com/
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202311281111.ou2oUL2i-lkp@intel.com/
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto API's support for alignmasks for ahash algorithms is nearly
useless, as its only effect is to cause the API to align the key and
result buffers. The drivers that happen to be specifying an alignmask
for ahash rarely actually need it. When they do, it's easily fixable,
especially considering that these buffers cannot be used for DMA.
In preparation for removing alignmask support from ahash, this patch
makes the stm32 driver no longer use it. This driver didn't actually
rely on it; it only writes to the result buffer in stm32_hash_finish(),
simply using memcpy(). And stm32_hash_setkey() does not assume any
alignment for the key buffer.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
The driver adapted here suffered from this wrong assumption and had
several error paths resulting in resource leaks.
The check for cryp being non-NULL is harmless. This can never happen as
.remove() is only called after .probe() completed successfully and in
that case drvdata was set to a non-NULL value. So this check can just be
dropped.
If pm_runtime_get() fails, the other resources held by the device must
still be freed. Only clk_disable_unprepare() should be skipped as the
pm_runtime_get() failed to call clk_prepare_enable().
After these changes the remove function returns zero unconditionally and
can trivially be converted to the prototype required for .remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
The driver adapted here suffered from this wrong assumption and had an
error paths resulting in resource leaks.
If pm_runtime_get() fails, the other resources held by the device must
still be freed. Only clk_disable() should be skipped as the
pm_runtime_get() failed to call clk_enable().
After this change the remove function returns zero unconditionally and
can trivially be converted to the prototype required for .remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The stm32 crc32 algorithms set a nonzero alignmask, but they don't seem
to actually need it. Their ->update function already has code that
handles aligning the data to the same alignment that the alignmask
specifies, their ->setkey function already uses get_unaligned_le32(),
and their ->final function already uses put_unaligned_le32().
Therefore, stop setting the alignmask. This will allow these algorithms
to keep being registered after alignmask support is removed from shash.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The callbacks for prepare and unprepare request in crypto_engine
is superfluous. They can be done directly from do_one_request.
Move the code into do_one_request and remove the unused callbacks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
stm32_hash_remove() is only called after stm32_hash_probe() succeeded. In
this case platform_set_drvdata() was called with a non-NULL data patameter.
The check for hdev being non-NULL can be dropped because hdev is never NULL
(or something bad like memory corruption happened and then the check
doesn't help any more either).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If pm_runtime_get() (disguised as pm_runtime_resume_and_get()) fails, this
means the clk wasn't prepared and enabled. Returning early in this case
however is wrong as then the following resource frees are skipped and this
is never catched up. So do all the cleanups but clk_disable_unprepare().
Also don't emit a warning, as stm32_hash_runtime_resume() already emitted
one.
Note that the return value of stm32_hash_remove() is mostly ignored by
the device core. The only effect of returning zero instead of an error
value is to suppress another warning in platform_remove(). So return 0
even if pm_runtime_resume_and_get() failed.
Fixes: 8b4d566de6 ("crypto: stm32/hash - Add power management support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove flag HASH_FLAGS_DMA_READY as it can put the driver in a deadlock
state.
If the DMA automatically set the DCAL bit, the interrupt indicating the
end of a computation can be raised before the DMA complete sequence.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If IP has MDMAT support, set or reset the bit MDMAT in Control Register.
Fixes: b56403a25a ("crypto: stm32/hash - Support Ux500 hash")
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we are sending the data to HASH with the DMA, we send all the data
provided in the scatterlists of the request.
But in some cases (ex : tcrypt performances tests), we should only send
req->nbytes
When iterating through the scatterlist we verify if it is the last
scatterlist or if the number of bytes sent plus the data of the current
scatterlist is superior of the total number of bytes to hash.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We were reading the length of the scatterlist sg after copying value of
tsg inside.
So we are using the size of the previous scatterlist and for the first
one we are using an unitialised value.
Fix this by copying tsg in sg[0] before reading the size.
Fixes : 8a1012d3f2 ("crypto: stm32 - Support for STM32 HASH module")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit "crypto: stm32 - Fix empty message processing" remove the use of
the argument bufcnt in stm32_hash_write_ctrl.
Hence, we can remove it from the function prototype and simplify the
function declaration.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the all SHA-2 (up to 512) and SHA-3 algorithm support.
Update compatible table to add stm32mp13.
Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to commit 890cc39a87 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Crypto API hashing paradigm requires the hardware state to
be exported between *each* request because multiple unrelated
hashes may be processed concurrently.
The stm32 hardware is capable of producing the hardware hashing
state but it was only doing it in the export function. This is
not only broken for export as you can't export a kernel pointer
and reimport it, but it also means that concurrent hashing was
fundamentally broken.
Fix this by moving the saving and restoring of hardware hash
state between each and every hashing request.
Fixes: 8a1012d3f2 ("crypto: stm32 - Support for STM32 HASH module")
Reported-by: Li kunyu <kunyu@nfschina.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change the emptymsg check in stm32_hash_copy_hash to rely on whether
we have any existing hash state, rather than whether this particular
update request is empty.
Also avoid computing the hash for empty messages as this could hang.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The bit HASH_FLAGS_ERRORS was never used. Remove it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Create a new struct stm32_hash_state so that it may be exported
in future instead of the entire request context.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The variable hdev->err is never read so it can be removed.
Also remove a spurious inclusion of linux/crypto.h.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current finup code is unnecessarily convoluted. There is no
need to call update and final separately as update already does
all the necessary work on its own.
Simplify this by utilising the HASH_FLAGS_FINUP bit in rctx to
indicate only finup and use the HASH_FLAGS_FINAL bit instead to
signify processing common to both final and finup.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no need to poll separate for update and final. We could
merge them into do_one_request.
Also fix the error handling so that we don't poll (and overwrite
the error) when an error has already occurred.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CSR registers go from 0 to 53. So the number of registers
should be 54.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Ux500 has a hash block which is an ancestor to the STM32
hash block. With some minor code path additions we can
support also this variant in the STM32 driver. Differences:
- Ux500 only supports SHA1 and SHA256 (+/- MAC) so we split
up the algorithm registration per-algorithm and register
each algorithm along with its MAC variant separately.
- Ux500 does not have an interrupt to indicate that hash
calculation is complete, so we add code paths to handle
polling for completion if the interrupt is missing in the
device tree.
- Ux500 is lacking the SR status register, to check if an
operating is complete, we need to poll the HASH_STR_DCAL
bit in the HASH_STR register instead.
- Ux500 had the resulting hash at address offset 0x0c and
8 32bit registers ahead. We account for this with a special
code path when reading out the hash digest.
- Ux500 need a special bit set in the control register before
performing the final hash calculation on an empty message.
- Ux500 hashes on empty messages will be performed if the
above bit is set, but are incorrect. For this reason we
just make an inline synchronous hash using a fallback
hash.
Tested on the Ux500 Golden device with the extended tests.
Acked-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When calculating the hash using the CPU, right before the final
hash calculation, heavy testing on Ux500 reveals that it is wise
to wait for the hardware to go idle before calculating the
final hash.
The default test vectors mostly worked fine, but when I used the
extensive tests and stress the hardware I ran into this problem.
Acked-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When exporting state we are waiting indefinitely in the same
was as the ordinary stm32_hash_wait_busy() poll-for-completion
function but without a timeout, which means we could hang in
an eternal loop. Fix this by waiting for completion like the
rest of the code.
Acked-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We are passing (rctx->flags & HASH_FLAGS_FINUP) as indicator
for the final request but we already know this to be true since
we are in the (final) arm of an if-statement set from the same
flag. Just open-code it as true.
Acked-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When reading or writing crypto buffers the inner loops can
be replaced with readsl and writesl which will on ARM result
in a tight assembly loop, speeding up encryption/decryption
a little bit. This optimization was in the Ux500 driver so
let's carry it over to the STM32 driver.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds a few small quirks to handle the differences between
the STM32 and Ux500 cryp blocks. The following differences
are handled with special bool switch bits in the capabilities:
- The main difference is that some registers are removed, so we
add register offsets for all registers in the
per-variant data. Then we assign the right offsets for Ux500
vs the STM32 variants.
- The Ux500 does not support the aeads algorithms; gcm(aes)
and ccm(aes). Avoid registering them when running on Ux500.
- The Ux500 has a special "linear" key format and does some
elaborare bit swizzling of the key bits before writing them
into the key registers. This is written as an "application
note" inside the DB8500 design specification, and seems to
be the result of some mishap when assigning the data lines
to register bits. (STM32 has clearly fixed this.)
- The Ux500 does not have the KP "key prepare" bit in the
CR register. Instead, we need to set the KSE bit,
"key schedule encryption" bit which does the same thing
but is in bit 11 rather than being a special "algorithm
type" as on STM32. The algorithm must however be specified
as AES ECB while doing this.
- The Ux500 cannot just read out IV registers, we need to
set the KEYRDEN "key read enable" bit, as this protects
not just the key but also the IV from being read out.
Enable this bit before reading out the IV and disable it
afterwards.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Ux500 cryp and hash drivers are older versions of the
hardware managed by the stm32 driver.
Instead of trying to improve the Ux500 cryp and hash drivers,
start to switch over to the modern and more well-maintained
STM32 drivers.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are a couple of spelling mistakes in dev_err messages. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: nicolas.toromanoff@foss.st.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stm32_crc_remove, so we should fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The include/linux/crypto.h struct crypto_alg field cra_driver_name description
states "Unique name of the transformation provider. " ... " this contains the
name of the chip or provider and the name of the transformation algorithm."
In case of the stm32-crc driver, field cra_driver_name is identical for all
registered transformation providers and set to the name of the driver itself,
which is incorrect. This patch fixes it by assigning a unique cra_driver_name
to each registered transformation provider.
The kernel crash is triggered when the driver calls crypto_register_shashes()
which calls crypto_register_shash(), which calls crypto_register_alg(), which
calls __crypto_register_alg(), which returns -EEXIST, which is propagated
back through this call chain. Upon -EEXIST from crypto_register_shash(), the
crypto_register_shashes() starts unregistering the providers back, and calls
crypto_unregister_shash(), which calls crypto_unregister_alg(), and this is
where the BUG() triggers due to incorrect cra_refcnt.
Fixes: b51dbe9091 ("crypto: stm32 - Support for STM32 CRC32 crypto module")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: <stable@vger.kernel.org> # 4.12+
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Fabien Dessenne <fabien.dessenne@st.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Lionel Debieve <lionel.debieve@st.com>
Cc: Nicolas Toromanoff <nicolas.toromanoff@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-crypto@vger.kernel.org
Acked-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We should not call pm_runtime_resume_and_get where the reference
count is expected to be incremented unconditionally. This patch
reverts these calls to the original unconditional get_sync call.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 747bf30fd9 ("crypto: stm32/cryp - Fix PM reference leak...")
Fixes: 1cb3ad7019 ("crypto: stm32/hash - Fix PM reference leak...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CRYP IP checks the written key depending of the configuration, it's
safer to write the whole configuration to hardware then the key to avoid
unexpected key rejection.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extra crypto manager auto test were crashing or failling due
to 2 reasons:
- block in a dead loop (dues to issues in cipher end process management)
- crash due to read/write unmapped memory (this crash was also reported
when using openssl afalg engine)
Rework interrupt management, interrupts are masked as soon as they are
no more used: if input buffer is fully consumed, "Input FIFO not full"
interrupt is masked and if output buffer is full, "Output FIFO not
empty" interrupt is masked.
And crypto request finish when input *and* outpout buffer are fully
read/write.
About the crash due to unmapped memory, using scatterwalk_copychunks()
that will map and copy each block fix the issue.
Using this api and copying full block will also fix unaligned data
access, avoid early copy of in/out buffer, and make useless the extra
alignment constraint.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fixes the lrw autotest if lrw uses the CRYP as the AES block cipher
provider (as ecb(aes)). At end of request, CRYP should not update the IV
in case of ECB chaining mode. Indeed the ECB chaining mode never uses
the IV, but the software LRW chaining mode uses the IV field as
a counter and due to the (unexpected) update done by CRYP while the AES
block process, the counter get a wrong value when the IV overflow.
Fixes: 5f49f18d27 ("crypto: stm32/cryp - update to return iv_out")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some auto tests failed because driver wasn't returning the expected
error with some input size/iv value/tag size.
Now:
Return 0 early for empty buffer. (We don't need to start the engine for
an empty input buffer).
Accept any valid authsize for gcm(aes).
Return -EINVAL if iv for ccm(aes) is invalid.
Return -EINVAL if buffer size is a not a multiple of algorithm block size.
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Don't erase key:
If key is erased before the crypto_finalize_.*_request() call, some
pending process will run with a key={ 0 }.
Moreover if the key is reset at end of request, it breaks xts chaining
mode, as for last xts block (in case input len is not a multiple of
block) a new AES request is started without calling again set_key().
Fixes: 9e054ec21e ("crypto: stm32 - Support for STM32 CRYP crypto module")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
STM32 CRYP hardware doesn't manage CTR counter bigger than max U32, as
a workaround, at each block the current IV is saved, if the saved IV
lower u32 is 0xFFFFFFFF, the full IV is manually incremented, and set
in hardware.
Fixes: bbb2832620 ("crypto: stm32 - Fix sparse warnings")
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change driver to not print an error message when the device
probe is deferred for a clock resource.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change stm32 CRYP driver to defer its probe operation when
reset controller device is registered but has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch changes the cast in stm32_cryp_check_ctr_counter from
u32 to __be32 to match the prototype of stm32_cryp_hw_write_iv
correctly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
